I've seen a few post regarding the 4.3V at 100% thing, but they're too old and haven't really given me much information.
My main issue is that I'm experiencing unusually rapid battery drops after my phone reaches 12% charge, it'd drop to 0% in just a few seconds. I downloaded a few battery calibration apps thinking that it might be a calibration issue. In that process, I noticed that the voltage read by these apps (and even in the *#*#4636#*#* menu) when fully charge is 4,38 volts. It was my understanding that Li-Po batteries should be fully charged at 4.2 volts and that charging past that point is harmful for the battery.
I also noticed that if at this point (charged at 4.38 volts - 100%) I unplugg the charger, the battery indicator would show 100% for a while, until the voltage drops below 4.2V, at that point the porcentage would change to 99%, so it seems that the device is set recognize 4,2V as fully charge, but it continues charging after that point. Also, the green light turns on at 90%, is this normal?
I tried calibrating using this app but with no results. I'm trying the manual calibration now. What is going on here? Could this be a clibration issue or do I have a faulty battery?
I think it is not normal. My P6 drops even a little bit slower from 10%. current my P6 is on 6% and 3,627V. (Edit: Turn off: 3,55V / After charge 100%: 4,32V)
Next time i will charge, then i post the Voltage at 100% for you.
To calibrate the accu you don't need any app. Use P6 until it is automatic power off. Now turn it on so often until it will not start anymore, and only show a red accu on screen. Now charge to 100%, turn on, unplug charger. Now your accu is calibrated.
heross said:
I think it is not normal. My P6 drops even a little bit slower from 10%. current my P6 is on 6% and 3,627V. (Edit: Turn off: 3,55V / After charge 100%: 4,32V)
Next time i will charge, then i post the Voltage at 100% for you.
To calibrate the accu you don't need any app. Use P6 until it is automatic power off. Now turn it on so often until it will not start anymore, and only show a red accu on screen. Now charge to 100%, turn on, unplug charger. Now your accu is calibrated.
Click to expand...
Click to collapse
Thanks, heross. So apparently the >4.2V @ 100% is not so unusual. Does your phone remain at 100% for a relatively long time and drops to 99 after the voltage is below 4.2V? Mine does that, and it also turns the led green when it reaches 90%.
I'm sure the dropping from 12% o 0% in seconds cannot be normal, but I'm wondering if the above is a symptom that something is wrong or
if it's normal.
EDIT: Ok, the phone just turned off by itself, the quick drop hapenned as usual (12% to 0% in less than a minute) and the voltage fluctuated between 3,1 and 3,3 volts in the process, maybe even less than 3.1 V, but I'm not sure. I took a series of screen shots 2 seconds apart, I'll post them when I turn the phone on again, I'll let it charge as you suggested.
Yes LED green at 90% is normal. My P6 drops to 99% after 1-2minutes screen on or after a boot without charger.
12% to 0% in seconds is definitely not normal. Normal it goes down very slowly to 3% then it comes a Info and after 30sec it power off.
Hi
heross said:
Yes LED green at 90% is normal. My P6 drops to 99% after 1-2minutes screen on or after a boot without charger.
12% to 0% in seconds is definitely not normal. Normal it goes down very slowly to 3% then it comes a Info and after 30sec it power off.
Click to expand...
Click to collapse
Finished charging.
I've turned the phone on and it has been sitting at 100% for about 25 minutes at 4,348V with the screen on. (I even played a video with full brightess). After that it droped to 99% and 4,079V[/B]. That can't be normal.
I saw that the P6 battery is rated 4,35 volts, so i'm not too worried anymore abut that voltage and everyone else seems to have the same values, but this quick drop with 12% and the fact that it stays for so long at 100% does worries me.
The screenshots were taken 2 or 3 seconds apart. It doesn't give me a low battery warning at 15% like most phones, but at 8%
I'm still having this extremely annoying problem. The goddamn battery goes from 12-13% to 0% in a blink of an eye. I just plugged the charger at 8% and it show 0% right after and started charging from there. Voltages are strange too, it shows ~3,6 volts when it started dropping quickly. It has charged ~20% in less than ten minutes. Look at this behavior: sudden voltage drops, never went below 3,3V and dies at 3,6V (almost nominal voltage)
I've tried calibrating several with several methods a few times, I'd prefer to stop doing that since I know it stresses the battery.
Has anyone had this issue? Can someone please shed some light on WTH is wrong with this troublesome phone?
Saw this post now. I have the same problem but it is from 9% to 0% . I don't think it is the battery, i think it is how android reads your battery info. I managed to calibrate mine by charging it when off from 0% to 100%-didn't last for long, the problem appeared once again.
It stays to much at 100% after charging, so we have the same battery life. Might be the kernel, don't know. I home when emui 3.0 is relased comes with a new kernel as well.
mcgyani said:
Saw this post now. I have the same problem but it is from 9% to 0% . I don't think it is the battery, i think it is how android reads your battery info. I managed to calibrate mine by charging it when off from 0% to 100%-didn't last for long, the problem appeared once again.
It stays to much at 100% after charging, so we have the same battery life. Might be the kernel, don't know. I home when emui 3.0 is relased comes with a new kernel as well.
Click to expand...
Click to collapse
I also managed to fix it once, I don't remember exactly what I did (I've tried so many things) but it didn't last long either, it discharged normally one time, but the next time dropped from 12% to 0% again in seconds. When will EMUI 3.0 be released?
They said emui 3.0 will be released in the middle of november for p6 but they also said that it will be available for p7 since october -they kept their word and it is available but only for the chinese versions of p7. So i would expect emui 3.0 for p6 in december for the international version.
mcgyani said:
They said emui 3.0 will be released in the middle of november for p6 but they also said that it will be available for p7 since october -they kept their word and it is available but only for the chinese versions of p7. So i would expect emui 3.0 for p6 in december for the international version.
Click to expand...
Click to collapse
Ok, I think I managed to calibrate it, I'm not sure yet, I will update once the battery is drained so I can see how it behaves at low charge, but there are indications that it's working.
If you're experiencing the same problem as me, then you've probably noticed that after your phone drops quickly from 9% (in your case) to 0% and you plug the charger, the battery will charge up to 9% also very quickly. If this happens, then Android is not reading the battery info right and you'll get a 100% reading before it's actually fully charged, and will keep on charging past that point (which I believe is why it stays at 100% for such a long time). It'll obviously drain from 9% to 0% again once it's discharged - because it's not really at 9%, it's much lower.
So, if we can manage to get Android to display normal charging speeds at low charge, then the battery should be calibrated. This is what I've managed to do.
Here's how:
1. Get a Battery Monitoring App (I use Battery Monitor Widget) and set the update intervals to 1 minute
2. Let your battery drain and your phone turn irself off until you can't turn it on
3. Plug the charger and turn the phone on. Watch how the charge increases in this process, it'll most likely charge too quickly (See graph screenshot - blue arrow: a steep slope indicates quick, abnormal charging speed readings)
4. Wait 5 minutes or until it reaches 10-12%
5. Unplug the charger and let the battery drain again. Watch how it discharges, if it charged too quickly in step 3, it'll most likely discharge quickly too here (You can see in the graph screenshot that the discharging slope in this process is also very steep)
6. When it says it's going to turn itself off in 30 seconds, plug in the charger (don't let it turn off).
7. If the 'turning off' message appeared, say, at 2%, your phone will probably display 0% after you plug the charger (i know this makes no sense, but it happens like that)
8. Let it charge and watch how it's charging.
After doing this my battery charged at a normal rate (Graph screenshot - red arrow) and it behaved normally approaching full charge (current started decreasing approaching 100% - green arrow). It didn't stay for ages in 100% after unplugging the charger either, just 1 hour in deep sleep (2nd and 3rd screenshots), which I think is fine because I used to unplugg the charger at night and wake up to a 100% battery, so it seems Android is reading battery info correctly now.
I hope this works for you too, mate (And that it will last more than one charge cycle).
I'll update tonight with low charge behaviour, but I'm pretty sure it'll discharge normally.
EDIT: It didn't actually eliminate the problem, but it got a little better, it now drops from 7% to 4% (instead of 12-13%) and stays at 4 for a while.
Related
Here are my observations.
1) While charging with the phone power off. I notice I won't get a full charge (95% show when I have my phone on) Then the power will drop very rapidly. 4 hours standby and i am on 90%
2) Charging with the phone On, by in sleep mode. Same issue. Green light on and my phone show around 98%, and after 4 hours of use. drop to around 90% ish.
3) Method 1 or 2, Then i unplug the USB and plug in again. Phone will charge for around 10min. Battery indicator show 100% full charge. I manage to use the phone for:
- 58 hours standby
- 2 hours of talk time
- 5 hours of device operation
The device configuration is the same. Programs are install the same.
Anyone having the same issue?
I noticed with mine if i plug it in at night when i sleep it will charge fully then die while charged. Example. i will charge it from like 5% then ill wake up at like 4 am and see its 100% but ill leave it plugged in then in the morning when i get up it will be between 89%-95%.
You are using the battery patch. But it isn't fully accurate so it's hard to make any conclusions
My 2nd test result.
With the method of just leaving the phone charge overnight and unplug in the morning without topping the battery back to 100%. the result is
Standby: 41 hours and 40 min
Talk Time: 42min
Device Usage: 3 hours and 36min
Let me charge it again tonight and top up to 100% in the morning before i use the device. see if the usage time be better.
What I have noticed is that after the phone reaches 100% it stops using mains power and switches to battery.
So if I plug it in at 10pm, and it reaches 100% by say midnight. It will be running off battery from midnight, so when I wake up it is often down to 90-95%. The charge light still shows green.
This is backed up by the info in power section of the settings, which shows the "last full charged reached" or similar section.
So in summary, even if it is still plugged into the wall, after hitting 100% it will switch to battery (even though the phone indicates charging).
Anyone got a solution for this?
Last full charge was on 8th August. 3G ON 24/7 for Push E-mails
Standby time - 30hrs and 6mins
Device Usage - 3hours and 11mins
and I still have 60% battery left.
powersquad said:
Last full charge was on 8th August. 3G ON 24/7 for Push E-mails
Standby time - 30hrs and 6mins
Device Usage - 3hours and 11mins
and I still have 60% battery left.
Click to expand...
Click to collapse
Jeez, mine wont last more than 8 hours with gprs and push email..
Does anybody elses TP2 switch to battery power once 100% charge is reached?
And anyway we can fix this?
Very annoying to wake up to a phone at 90% charge even thought it is plugged into the wall.
Hi all,
I've been having issues with my phone lasting nowhere as long as my girlfriends identical one,
I installed Quick System Info on both phones, Killed all tasks.. Not only is my display duller than hers on the lowest setting using the power control widget but the voltage on my battery is 3737mV while hers is 4071mV..
Is this cause for concern?
Update, forgot to mention, this is from a full charge on both handsets.
Sounds like your battery is fu#ked!
There seems to be an issue with the way android reports the battery voltage. If I leave my phone on the charger until the light goes green and the indicator says 100%, the voltage will often report between 4.146v - 4.156v.
Upon unplugging the phone would drop to 99% and 4.125v almost immediately.
I noticed the other day that after leaving the battery on the charger overnight the voltage was reporting as 4.206v and I was able to use the phone for over 15min before it dropped to 99% from 100%.
Minimum voltage before your phone powers off is around 3.6v - 3.650v. So 3.737 is pretty close to the cut-off point. The OS is may report 100% charge but your battery is not holding charge.
I had a battery on a different device that was like this. The battery had collapsed. I could charge it for 24hrs and it would not make a difference. Within 30min of use or 1 phone call it would die.
Does your battery have any bugles, bumps or protrusions? This is often a sign of a collapsed battery.
Edit: Don't write when you're tired, silly things come out of your fingers! Soz!
have you tried to swap batteries between the two phones. That will exclude either your phone or the battery from being faulty.
Yes, after scratching my head for a few days I did eventualy come up with the genius idea of putting the battery from the other phone into my phone!! and after charging it up, set it down for an hour and then checked and the battery was on 98% !!
So it looks like there is something wrong with my battery, This morning I woke up and my phone had been charging for 7 hours and was fully charged, I looked at the battery meter and it said 100%, I turned the phone off then back on and checked again.. 90% ???? WTF ??? just from turning the phone off and on?
Hi all
Just after an opinion really, also see if anyone else is having a similar problem with there battery??
I've had my desire now since April, and recently been having issues with the battery. When charging it, the Orange LED charge light will turn green at around 94% charge and still climb to 100%. Then when its charged (for a whole night) I unplug it, battery states 100% charge for about a minute, then drops straight to 93%. I've tried it with a few roms now, standard Rom, froyo, now on pays bravesoul release, and they all do the same...
I've tried resetting battery charge status in recovery console too, but made no difference...
Surely the standard battery can't be on its way out already??
*edit*
Info in my Sig is a bit out of date, so ignore what it says lol! Running latest pays bravesoul release as mentioned, not done any tweaks to this Rom yet!
Install JuicePlotter and then monitor the usage
report back
it should show whats using the battery when it takes a huge decrease
AFAIK the charging stops after reaching 100% (probably as safety measure)
and there doesn't seem to be a trickle charge function to keep it at 100%. This is actually a good thing 'cause Li-ion and Li-poly batteries don't like to stay in the highest or lowest regions too long.
So...charging stops at 100% and after that you're running on battery. Try charging it and unplug the charger when 100% is reached (look at the actual %, not the LED. You will notice it'll go down at the same rate it always does and no jump to 93%.
I think it charges to 100%, then allows itself to drop back to 90% (the phone still shows 100% though) and when you unplug the phone from the wall, it will drop back to the "actual charge".
If you plug it back in, it should start to charge back to 100%.
Hi fellas..
Maybe you've noticed the messages I've sent to Unofficial BravoS thread of Coolexe's (http://forum.xda-developers.com/showthread.php?t=1200517&page=51) which is the ROM I use.
The issue is, the battery discharges rapidly. Actually, if you check mV values, it doesn't discharge rapidly, but if you look at percentages, there is a huge inconsistency. I used Battery Monitor Widget to log the battery performances last night, and saw these horrible results:
Code:
2011/09/19|04:59:49|-515mA|37%|3581mV|40.2ºC|1|0
2011/09/19|05:00:51|-465mA|36%|3576mV|40.2ºC|1|0
2011/09/19|05:01:49|-460mA|36%|3576mV|40.2ºC|1|0
2011/09/19|05:02:50|-462mA|35%|3517mV|40.2ºC|1|0
2011/09/19|05:03:49|-477mA|35%|3517mV|40.2ºC|1|0
2011/09/19|05:04:50|-471mA|34%|3449mV|40.3ºC|1|0
2011/09/19|05:06:06|-478mA|0%|3415mV|40.5ºC|1|0
2011/09/19|05:06:08|-478mA|0%|3415mV|40.5ºC|1|0
These are the last lines of the log, before the phone shuts down. As you can see, the phone gone to 0% from 34% in one minute! No low battery warnings or whatsoever..
Funny thing is, this doesn't happen in StarBurst ROM (which is a Froyo based one). Do you reckon this is a GingerBread issue or something? I saw some other people complaining about their phone shutting down at 20% as well.
So, what do you suggest?
when you look at the voltage there isnt that much drain, so its only a displaying problem
wipe battery stats and maybe recalibrate the battery
but first one should fix it
cheers
ps: i just checked, my desire is at 18% with 3.693mV, now you see the differance
crendot said:
when you look at the voltage there isnt that much drain, so its only a displaying problem
wipe battery stats and maybe recalibrate the battery
but first one should fix it
cheers
ps: i just checked, my desire is at 18% with 3.693mV, now you see the differance
Click to expand...
Click to collapse
This is what I've done so far:
Drained battery to 0% (log above) and charged it a little bit while powered off (like 20%). Turned on the phone, and obtained those logs (last lines only):
Code:
2011/09/19|14:41:25|-268mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:42:25|-267mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:43:25|-270mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:44:25|-269mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:45:25|-267mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:46:25|-268mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:47:25|-266mA|8%|3644mV|38.1ºC|1|0
2011/09/19|14:48:25|-267mA|8%|3644mV|38.1ºC|1|0
2011/09/19|14:49:25|-269mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:50:25|-267mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:51:25|-266mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:52:25|-267mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:53:25|-267mA|6%|3640mV|38.0ºC|1|0
2011/09/19|14:54:25|-267mA|6%|3640mV|38.0ºC|1|0
2011/09/19|14:55:25|-267mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:56:25|-266mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:57:25|-267mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:58:25|-268mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:59:25|-268mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:00:25|-319mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:01:25|-268mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:02:25|-270mA|3%|3610mV|38.1ºC|1|0
2011/09/19|15:03:25|-269mA|3%|3610mV|38.1ºC|1|0
2011/09/19|15:04:25|-270mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:05:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:06:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:07:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:08:25|-289mA|1%|3513mV|38.3ºC|1|0
2011/09/19|15:09:25|-290mA|1%|3513mV|38.3ºC|1|0
2011/09/19|15:09:51|-290mA|0%|3464mV|38.3ºC|1|0
It seems more "smooth" discharge now. Right now, I'm charging my phone off; going to turn on phone once it reaches "green light" with charger on, and plug it off once phone booted. Maybe then, it can know what's maximum and minimum.
So far, I tried to charge my phone to full and erase batterystats.bin but, as you can see at the first post, it didn't work well.. On the other hand, the phone charged-discharged only once in this ROM, you think it could be better if I've given a "second chance"?
i dont know much about that "battery calibrating" and reseting stuff, you have to search in the forum
only thing i want to say is, dont do that deep drains!
recharge at least 5%! you kill your battery, lithium-ion batterys get serious damage from deep drains
crendot said:
i dont know much about that "battery calibrating" and reseting stuff, you have to search in the forum
only thing i want to say is, dont do that deep drains!
recharge at least 5%! you kill your battery, lithium-ion batterys get serious damage from deep drains
Click to expand...
Click to collapse
I know, but when phone thinks it's 30% and not warn me, how can I do it?
In order to calibrate the battery meter - FYI the battery itself cannot be calibrated, as Li-Ion batteries have a very low memory compared to old Ni-Cd etc. batteries - you have to go through the following procedure:
1) charge the battery to 100%;
2) let the battery discharge until the phone shuts itself down;
3) plug the wall charger into the phone, boot the phone up then charge the battery to 100% without interruptions.
If the above procedure does not yield the expected results, you can try fully charging the phone (LED showing green) with it completely turned off (after completely draining it). Again, the charging procedure should not be interrupted.
Source: personal experience - had to do this twice after installing new ROMs, as the phone was shutting down at ~14% (working like a charm now).
Regarding the matter of battery wear because of complete discharges, Li-Ion batteries do indeed have a lower cycle count than old-school batteries, but the standard charge/discharge number a Li-Ion battery can take is ~350, so you can't damage the battery pack by doing a full cycle per month (required to keep the battery meter accurate).
Good luck!
TVTV said:
In order to calibrate the battery meter - FYI the battery itself cannot be calibrated, as Li-Ion batteries have a very low memory compared to old Ni-Cd etc. batteries - you have to go through the following procedure:
1) charge the battery to 100%;
2) let the battery discharge until the phone shuts itself down;
3) plug the wall charger into the phone, boot the phone up then charge the battery to 100% without interruptions.
If the above procedure does not yield the expected results, you can try fully charging the phone (LED showing green) with it completely turned off (after completely draining it). Again, the charging procedure should not be interrupted.
Source: personal experience - had to do this twice after installing new ROMs, as the phone was shutting down at ~14% (working like a charm now).
Regarding the matter of battery wear because of complete discharges, Li-Ion batteries do indeed have a lower cycle count than old-school batteries, but the standard charge/discharge number a Li-Ion battery can take is ~350, so you can't damage the battery pack by doing a full cycle per month (required to keep the battery meter accurate).
Good luck!
Click to expand...
Click to collapse
Thanks for your answer...
Today I realized that it my concern was a quick one. Today, I discharged battery to 0 percent, plugged the AC charger while it's OFF and charged it for around 2h22m until Led-green-full; then turned on the phone with charger plugged and plugged it off just after the boot process. After that, I let the phone to discharge (I helped it a little )
I actually saw "Plug your charger" warning this time, and according to Bat. Mon. Widget, it gone down until 13%! If I do compare the mV values with the old ones, I can see that somehow the phone does learn which mV value correspond to which percentage better.
Even though it gone from 13% to 0% in two minutes, it's at least better than 30% to 0%.. Also, when I check the readings after I plugged in, I saw that percentage-voltage matching is slightly higher, showing that the phone now shows lower percentage for the same voltage - which shows that it learns percentage better.
After one or two charge-discharge cycle, I think it'll learn absolute 0
BTW; the battery says 3.4V 1400mAh and my maximum voltage is 4160mV (100%) and minimum is 3415mV (0%). Are these values normal, you think?
PS: What I'd recommend from anyone who loves flashing ROMs as much as I do is: AFTER YOU FLASHED A NEW ROM, CHARGE YOUR BATTERY TO FULL (100%) AND ERASE THE BATTERY STATS. AFTER THIS, NEVER, I SAY, NEVER ERASE YOUR BATTERY STATS FOR LONG TIME IN ORDER FOR YOUR PHONE TO LEARN STATS BETTER! Erase after long time, say 3 months for wear effects to be accounted, but well, I think you should be fine even after you don't do this
Maybe you did already know that, but, well, I learned it hard way
EDIT: Phone shutdown at 13% after this, but I think it'll do better in time..
Can't Calibrate the Widget
I am having a similar issue with my htc aria. Problem is that it gets to about 78% and then won't go any higher. It even shows (in Battery Monitor Widget)
"Discharging" and "AC plugged". I have let it sit plenty long enough to be fully charged and then completely discharged it (until it shut itself down, which was not 0%) and recharged until it reaches 78% again and stops charging. I'm guessing it is so far out of whack that it says I'm at 78% but I am really at 100%.
The widget says to charge to 100% and then drain completely to 0% to calibrate. I can't do either from what I can tell. So what to do?
theGanymedes said:
Today, I discharged battery to 0 percent, plugged the AC charger while it's OFF and charged it for around 2h22m until Led-green-full; then turned on the phone with charger plugged and plugged it off just after the boot process.
Click to expand...
Click to collapse
Quick tip - let the phone charge for another hour or so after the light goes green (when charging it while powered off). I've read that the light goes green at about 95%. It takes another hour for the phone to really charge to 100%. That's because Li-Ion batteries use two stages to charge: a fast one and a slow one. More details here.
Glad i could help.
P.S. - It also took me two complete charge/discharge cycles to fully calibrate my battery meter after switching from FroYo to Gingerbread.
@vkyjackie - Try fully charging the phone while powered off. If it still doesn't fully charge (LED green), then you might have an issue with either the battery pack or the wall charger.
I've noticed that my 2 XL battery drains very fast after full charge, but then settles to acceptable drain rates from about 90%. I'd say it takes less than an hour to drop from 100 to 90% without basically any use. Often I can't even hit 100% when charging. More like 99/98% max. If it does charge to 100%, it stays there for a couple minutes tops, even if just on standby. Which leads me to my next issue...
This prompted me to calibrate my battery which seemed to help somewhat, but I found that I cannot monitor the charge rate when charging while the device is turned off. What is shown is just what "looks like" a full battery charged icon at all times, and the screen does not dim at any point during charge. It actually seems that the phone is frozen during charging when turned off, and needs a very long power button press to turn the phone on. I actually have two Pixel 2 XLs in front of me and they both do this! Is this a known issue?
In general I am getting 5-6 hours screen-on time per charge which seems about right from what I've read. But that initial fast drain and "freezing" while charging when turned off is puzzling. Any common experiences or insight?
nobaddreams said:
I've noticed that my 2 XL battery drains very fast after full charge, but then settles to acceptable drain rates from about 90%. I'd say it takes less than an hour to drop from 100 to 90% without basically any use. Often I can't even hit 100% when charging. More like 99/98% max. If it does charge to 100%, it stays there for a couple minutes tops, even if just on standby. Which leads me to my next issue...
This prompted me to calibrate my battery which seemed to help somewhat, but I found that I cannot monitor the charge rate when charging while the device is turned off. What is shown is just what "looks like" a full battery charged icon at all times, and the screen does not dim at any point during charge. It actually seems that the phone is frozen during charging when turned off, and needs a very long power button press to turn the phone on. I actually have two Pixel 2 XLs in front of me and they both do this! Is this a known issue?
In general I am getting 5-6 hours screen-on time per charge which seems about right from what I've read. But that initial fast drain and "freezing" while charging when turned off is puzzling. Any common experiences or insight?
Click to expand...
Click to collapse
It may be that the battery is not fully charged when the phone is telling you it is 100%. When using Accubattery to manually benchmark the battery, I found that my phones were still taking a low charge current (as measured by AB) for 45 minutes to sometimes even one hour after the phone was reading 100%. AB will register 100% when the phone's charging circuit cuts off to zero (and notify you). Using AB for a while will also give you a very close approximation of the remaining capacity of your battery relative to a new battery. When my 2XL was new, I was getting just over 100% (~103%). A year later, it is in the high 90's.
Thanks for the tip on Accubattery. I am going to give that a try for a while. So have you been charging up to 100% regularly in spite of what's recommended by this app?
nobaddreams said:
Thanks for the tip on Accubattery. I am going to give that a try for a while. So have you been charging up to 100% regularly in spite of what's recommended by this app?
Click to expand...
Click to collapse
Yes, I turn the 80% alarm crap off and leave it on the charger all night. It is fully charged before I go to bed but I leave it on the charger all night. I use AB for bench marking my battery's capacity and it's real good at that... if you start from when AB says your battery is full. You will see it converge to a % capacity after only 2-3 full discharges. I'm just guessing but I think you are not completely filling the battery to it's full capacity. At least using AB for a while will a) provide you with your battery's true capacity wrt a new battery, and b) will rule out you not charging up fully as your mystery 100-90% quick-drop. Please do report back. :good: