I find that 9 time out of 10 when I look at my watch, the screen is black. So the one thing this watch is no good for is telling time.
Is there a way to increase the sensitivity so that the watch lights up easier? I shouldn't have to use 2 hands to operate a watch.
Do you wear your watch on the bottom of your wrist? Or do you wear it on your right hand? I've found that it is almost perfect at detecting when I want it to wake, only when it is on the top of my left wrist.
Have you tried restarting the watch? The watch should wake up whenever you turn your wrist to look at it
So I've finally had the chance to play with one of these watches extensively, and I am baffled by ambient mode.
It's not that it still turns off sometimes; that makes perfect sense. What's wrong with it is that it doesn't actually update even when the screen is on.
Test it yourself. Use the default watch face, enable ambient mode, and go in a completely dark room. You can leave the watch still or move it about, just don't let it act as if you're raising your arm and brighten the display.
Watch it for two or three minutes, and you'll notice that even though the screen remains on, it never updates -- the minute hand never moves, and so it doesn't actually show the right time very quickly after it dims. (This is with the official, default watch face, a just-rest watch, the latest firmware installed, and plenty of battery remaining.)
When the screen turns on from a raise or tap in ambient mode, you can actually see the minute hand jump forward several minutes in one go. Even with ambient mode disabled, the watch still turns on automatically with the raise gesture, and it takes no longer to do so than it does in ambient mode.
That implies there is no reason to use it other than vanity. After all, in the brief time before the backlight comes on the watch shows the wrong time, and it doesn't actually show the right time any faster than it would have.
But it's not really a vanity mode either, because except in a very dark place, the dimmed screen is indistinguishable from a powered off one to those standing near you. So you're wasting power, but still look like you have a blank screen on your wrist.
So what, precisely, is the point? It seems to me to add no benefit, just to waste battery. I'm baffled.
Sent from my Nexus 10 using Tapatalk
I played with Ambient Mode a little before the recent update, but battery life just wasn't sufficient to keep it on. After the update, battery life improved enough for Ambient Mode, so I switched it on. I dealt with it a couple days, then ultimately turned it off for this very reason. It just seemed clunky to me, and as you stated, I'd often glance at my wrist only to see the wrong time until suddenly the watch came fully on and updated.
I was excited for Ambient mode, but like you, I no longer see the point. I'd rather just have a user-controllable setting for "fully on" sensitivity. If I could make my 360 just a little more sensitive to my raising my wrist action, it'd be perfect without Ambient Mode.
I wish I could have the screen on all the time in some cases.. like if you go to someplace classy, i would have the face on all the time displaying the watch face. Thats just me.
I've seen the screen update while it was dim. I do think that it is too dim to use outside like you mentioned.
I noticed this as well. Surely just a bug or an issue with android wear that will be fixed at some point. I'm also sure they will provide a lot more features to regulate screen controls, on, off, brightness, etc in future updates. It's just a matter of time.
I look at it this way... the sensor is kind of future proof if anything. Might not be very useful now, but could have a lot of potential in the next few months or once custom ROM's start rolling out.
Android wear is still in the early stages. It can only get better. Just be patient, we are early adopters on first generation hardware.
tlxxxsracer said:
I wish I could have the screen on all the time in some cases.. like if you go to someplace classy, i would have the face on all the time displaying the watch face. Thats just me.
Click to expand...
Click to collapse
Here is a way you can set the screen on all the time:
http://forum.xda-developers.com/showthread.php?p=55311726
knoxploration said:
So I've finally had the chance to play with one of these watches extensively, and I am baffled by ambient mode.
It's not that it still turns off sometimes; that makes perfect sense. What's wrong with it is that it doesn't actually update even when the screen is on.
Test it yourself. Use the default watch face, enable ambient mode, and go in a completely dark room. You can leave the watch still or move it about, just don't let it act as if you're raising your arm and brighten the display.
Watch it for two or three minutes, and you'll notice that even though the screen remains on, it never updates -- the minute hand never moves, and so it doesn't actually show the right time very quickly after it dims. (This is with the official, default watch face, a just-rest watch, the latest firmware installed, and plenty of battery remaining.)
When the screen turns on from a raise or tap in ambient mode, you can actually see the minute hand jump forward several minutes in one go. Even with ambient mode disabled, the watch still turns on automatically with the raise gesture, and it takes no longer to do so than it does in ambient mode.
That implies there is no reason to use it other than vanity. After all, in the brief time before the backlight comes on the watch shows the wrong time, and it doesn't actually show the right time any faster than it would have.
But it's not really a vanity mode either, because except in a very dark place, the dimmed screen is indistinguishable from a powered off one to those standing near you. So you're wasting power, but still look like you have a blank screen on your wrist.
So what, precisely, is the point? It seems to me to add no benefit, just to waste battery. I'm baffled.
Sent from my Nexus 10 using Tapatalk
Click to expand...
Click to collapse
Just watched mine move the minutes hand just fine in ambient mode... this is with the classic Motorola face.
https://www.youtube.com/watch?v=HsTpDpgYwFY
I have started using ambient mode for the first time in a bright office environment and noticed that at random times the display completely turns off. It turns back on once I move my hand ever so slightly. For me Ambient Mode should always be on regardless of lighting condition and watch orientation.
zarks said:
I have started using ambient mode for the first time in a bright office environment and noticed that at random times the display completely turns off. It turns back on once I move my hand ever so slightly. For me Ambient Mode should always be on regardless of lighting condition and watch orientation.
Click to expand...
Click to collapse
I thought it would stay on the dimmed mode the whole time too... but like you said it turns on with even the slightest rotation of the wrist now, and that means we can finally glance at the watch and see the time!
:good:
The minuets do update in real time so idk what you're seeing?
This observation definitely needs to be settled because we have 2 conflicting reports here. Some of you are claiming the watch does not update the time even when the screen is on unless you fully wake the screen. Others are saying it updates just fine, so what gives?
FYI my G watch always displays the correct time, even when dimmed, so I dont think it's an Android Wear problem. Sounds kinda like additional battery conservation steps by Moto. They are essentially sleeping the CPU so that there is just enough juice remaining to keep the screen on for 16+ hours. I just dont understand how some of you are experiencing this and others are not.
for me, in ambient mode, the screen still turns off after a while. but it turns back on much quicker than with ambient mode off. it often takes an exaggerated bring-up-arm movement to turn on the screen with ambient off. i used to resort to tapping the screen instead. with ambient on the battery still last me a "work day". off charger at 7AM and dies around 10PM or so...battery lasts longer with stock faces compared to Facer faces...
Most developer purposes.
My ambient mode used to stay on all the time now it turns off the screen..
ws6kid said:
My ambient mode used to stay on all the time now it turns off the screen..
Click to expand...
Click to collapse
I just started using it and noticed the screen stays on if you keep it flat horizontal, but if you turn your wrist past 45 degrees it turns off.
Maybe they added that with the update, did ambient mode used to stay on even when that watch is sideways?
Ambient is so useless for me, the screen is almost off all the time... So frustrating coming from a g watch
RunNgun42 said:
This observation definitely needs to be settled because we have 2 conflicting reports here. Some of you are claiming the watch does not update the time even when the screen is on unless you fully wake the screen. Others are saying it updates just fine, so what gives?
FYI my G watch always displays the correct time, even when dimmed, so I dont think it's an Android Wear problem. Sounds kinda like additional battery conservation steps by Moto. They are essentially sleeping the CPU so that there is just enough juice remaining to keep the screen on for 16+ hours. I just dont understand how some of you are experiencing this and others are not.
Click to expand...
Click to collapse
For me, I believe I have seen my watch 'get stuck' maybe once or twice where the time on the dim screen wasn't the same as I had on my computer. This could just be a difference in the clocks, as whenever I check both my phone and my dim watch together, they are the same. Like RunNgun42 said, I think it might be a thing where the proc is in sleep mode to try and save power and isn't keeping up the time as accurately as it could. Once you shake it though and the screen lights up again, the proc will come out of sleep and maintain more accurate timekeeping.
Isn't there a screen always on option in the android wear app?
And yes ambient mode still turns off when the watch is at an angle consistent with being down at your side or is completely still.
SilentAce07 said:
Isn't there a screen always on option in the android wear app?
Click to expand...
Click to collapse
No, you can't keep the screen on at all times out of the box, but some 3rd party software can do it...
Ambient mode is a lot quicker to wake up and react than non-ambient, it's a lot more accurate (non-ambient often stays off when I turn my arm to look at the time), it's easier to see what time it is, and it acts a lot more like a conventional watch- the display is on when you need it.
Battery drain is not a biggie, I get through the day, every day.
1) Can i disable the functions of "cardiac activity" "pedometer" ?!
2) Battery life is very bad, what can I do to optimize it?
3) On reminders and alarm clocks, it doesn't vibrate, why?
nothing?
up
I just got mine and the performance was horrible. I had to let the software update to 5.x from 4.x and after that was done I deleted it from my phone and then did a factory reset on the watch. After I did all that I used a moto watchface and had 36 hours.
On optimising battery life:
Turn off gestures (tilt to wake, etc), ambient mode (the display doesn't need to be on all the time, press the side button or tap the screen), and wifi. I also turn mine off every night when I go to sleep (I never wear a watch to bed, anyway) and I can usually get 3-4 days out of mine, with decent use of the actual smartwatch features (voice texting, media control, responding to notifications).
tygerchylde said:
On optimising battery life:
Turn off gestures (tilt to wake, etc), ..........
Click to expand...
Click to collapse
Although it rear tilt to wake option is disabled, the watch lights up when it turned up in the display.
Probably something else causing it to light up, but I'm not sure now what.
If there is a clock faces that have settings for this, those in the WatchMaker Premium application do not have this option to turn off tilt to wake up for reduce the battery consumation.
Monipeev said:
Although it rear tilt to wake option is disabled, the watch lights up when it turned up in the display.
Probably something else causing it to light up, but I'm not sure now what.
If there is a clock faces that have settings for this, those in the WatchMaker Premium application do not have this option to turn off tilt to wake up for reduce the battery consumation.
Click to expand...
Click to collapse
The Android Wear app is the only place that I know of where the tilt to wake option is located.
I don't use either Facer or Watchmaker Premium, so I'm not sure about that option under either app.
Using either app can cause extra battery drain, since the watch communicates with the phone constantly (or at least frequently) to update the watch face.
tygerchylde said:
The Android Wear app is the only place that I know of where the tilt to wake option is located.
I don't use either Facer or Watchmaker Premium, so I'm not sure about that option under either app.
Using either app can cause extra battery drain, since the watch communicates with the phone constantly (or at least frequently) to update the watch face.
Click to expand...
Click to collapse
You're right. I probably had in mind the possibility of stopping this option from the watch itself, which does not happen until you stop the application Android Wear, as you mentioned.
Alternatively, it is talking about is removing dim off the clock.
Thanks for your guidance.
Hello,
My huwawei smartwatch sometimes turns off its screen automatically to full black, not the screens saver mode. So I need to touch my watch again to get the display on again.
What can I do about it?
Thank you for reading,
Genezing
This is a new energy saving feature. It will switch off the display if the watch doesn't move for a certain time. I also experience this sometimes, especially when playing with my Playstation. I usually rest my arms and mainly move only my fingers while playing. This causes my watch to go to sleep.
Unfortunately, there is nothing you can do about it. But it should not happen during normal activities, when you move your arm from time to time at least a little.
Happens to me when playing games, I figured it had to be some energy saving tech., glad to hear confirmation.