Hi,
Just brought my note II three days ago, and looking to update on 4.3. Phone was rooted, Philz installed, stock rom installed (this on : http://forum.xda-developers.com/showthread.php?t=2605464).
After boot I didn't have wifi, so I follow the instructions to install the bootloader, and after that impossible to boot and impossible to flash again.
I don't know if it's because the bootloader is locked or the NAND is corrupted.
I tried to flash with original stock to fix, but same result, always the same result.
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUEMK8_N7100OXAEMK1_N7100XXUEMJ9_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
[COLOR="DarkOrange"][B]<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL![/B][/COLOR]
<OSM> All threads completed. (succeed 0 / failed 1)
There are two things You can try.... Flashing using hemdall recovery or else try flashing the firmware along with the modem file. It worked for me. Do try this after re-installing the Samsung USB driver.
Sent from my GT-N7100 using XDA Premium 4 mobile app
I will look for thx.
Do you have a link for the firmware + modem you installed please.
The modem is integrate the TAR I downloaded I guess (got it from sammobile).
Since my S2, it's first time I have a problem, usually I found the answer on the forum or internent, but not this time.
Zubair1024 said:
There are two things You can try.... Flashing using hemdall recovery or else try flashing the firmware along with the modem file. It worked for me. Do try this after re-installing the Samsung USB driver.
Sent from my GT-N7100 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Yes you find the modem you were using and flash it with the rom in Odin. Next time if Wi-Fi doesn't turn on don't flash the bootloader instead Flash Dr ketan's Wi-Fi patch zip file in recovery. It worked for me.
Sent from my GT-N7100 using xda premium
Code:
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> modem.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
[B][COLOR="DarkOrange"]<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<ID:0/003> FAIL![/COLOR][/B]
<OSM> All threads completed. (succeed 0 / failed 1)
That didn't work u.u
I tried to flash Stock ROM + MODEM, MODEM alone, always the same problem. (I used odin3.07)
I will try with the other soft, but I have to look for the tar.gz or change my tar.md5 to tar.gz (...but not with windows, i'm not confident in it for that -_-)
A friend of mine bought a refurb note 2 a while ago and im trying to help her fix her phone. The problem is it's stuck on tmobile bootscreen and it wont boot to recovery mode for some reason. Although it can boot to download mode and I doubt its rooted cause knox warranty says 0, I could be wrong though. Has anyone had this problem? Any help/suggestions would be greatly appreciated.
EDIT: I just tried premiatul's suggestion earlier but odin gave me an error.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I used the 4.3 JB Stock Rom and it didn't work. Now I'm back to square one
Flash this with ODIN:
http://forum.xda-developers.com/showthread.php?t=1975560
Sent from my SGH-T889 using xda premium
premiatul said:
Flash this with ODIN:
http://forum.xda-developers.com/showthread.php?t=1975560
Sent from my SGH-T889 using xda premium
Click to expand...
Click to collapse
Should I flash it with 4.3 jelly bean? Idk what version she has but does it matter?
premiatul said:
Flash this with ODIN:
http://forum.xda-developers.com/showthread.php?t=1975560
Sent from my SGH-T889 using xda premium
Click to expand...
Click to collapse
I just tried premiatul's suggestion earlier but odin gave me an error.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I used the 4.3 JB Stock Rom and it didn't work. Now I'm back to square one
Anyone? I'm not sure If I'm even flashing the right ROM cause I don't even know the phone's firmware version.
Bump!
Hi guys,
after a lot of problem with my s4mini now the phone doesn't call and doesn't active the wifi connection. I've tried to flash all the modem i found, but every time the process is concluded with a fail (in odin)...
So i don't know i can i do.
Thanks to all
Atlantis
Try flashing a complete new firmware with Odin.
RoyaLKurTx3 said:
Try flashing a complete new firmware with Odin.
Click to expand...
Click to collapse
I tried many times but evrytime the process ends with a fail... Odin lets me flash only te recoverys...
atlantis87 said:
I tried many times but evrytime the process ends with a fail... Odin lets me flash only te recoverys...
Click to expand...
Click to collapse
Tell me all the steps that you are doing. And if you can, provide me some screenshots.
RoyaLKurTx3 said:
Tell me all the steps that you are doing. And if you can, provide me some screenshots.
Click to expand...
Click to collapse
Everything starts wit a mistake. I had CM snapshot 12 and i tried to flash the stock rom. Probably i wrong the version of the stock firmware. When the process ends with a fail the phone was softbriccked... I tried many things (exactly i don't remeber every thing i done...) and at the end th only way i found was to flash a new recovery. After that i flash CM12 but when i turn on the phone all the mobile connection (network and wifi) don't work... I tried to flash a lot of different modem but no one works...
I attach the screenshot of the dowload mode...
Thanks
atlantis87 said:
Everything starts wit a mistake. I had CM snapshot 12 and i tried to flash the stock rom. Probably i wrong the version of the stock firmware. When the process ends with a fail the phone was softbriccked... I tried many things (exactly i don't remeber every thing i done...) and at the end th only way i found was to flash a new recovery. After that i flash CM12 but when i turn on the phone all the mobile connection (network and wifi) don't work... I tried to flash a lot of different modem but no one works...
I attach the screenshot of the dowload mode...
Thanks
Click to expand...
Click to collapse
hi man try this :1 instal a custom CWM....2 enter to recovery mode 3-wipe data factory and wipe cach..3 format dalvik cach 4 format system and format modem...5 enter to odin mode 6 flach your stock rom 7 enjoy
Hi man. I have already tried step 1 2 3. Do you know how can i format statemi and modem? Thanks
atlantis87 said:
Hi man. I have already tried step 1 2 3. Do you know how can i format statemi and modem? Thanks
Click to expand...
Click to collapse
ok men 1 go to recovery 2 go to mounts and storage 3 format system 4 format modem 5 fomat cache.and after this flash your stock rom
ok, i tried and....
nothing
when i try to flash something odin answer the row below...
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
But... a question... in the download mode the last row is "WRITE PROTECTION: ENABLED"... Can influence somthing this thing??
Thanks
Be careful when you format system, it's dangerous and the only fix for it is flashing a ROM.
Try these:
1. Download this and extract the files in the ZIP: http://www.sammobile.com/firmwares/download/40040/I9195XXUCNK4_I9195OXXCNK5_SEE.zip/
2. You should get 2 files;
I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5
SS_DL.dll
Ignore the SS_DL.dll. You will use the other file.
3. Go to Odin and thick only 'Auto Reboot' and 'F. Reset Time'. Now Insert the .tar.md5 I named above in the AP place.
4. Turn off your phone and boot into recovery. Clear data and cache. Now restart to download mode.
5. If you are asked to continue or to cancel and restart phone, choose continue.
6. Keep your phone like that and check that you have this (or similar) layout in Odin;
Now press start and wait until everything have finished and your phone boots (May take 8-11 minutes) If you followed these steps and you got a fail, then you must have done something wrong or your phone has something wrong in terms of hardware. Good Luck mate.
atlantis87 said:
ok, i tried and....
nothing
when i try to flash something odin answer the row below...
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
But... a question... in the download mode the last row is "WRITE PROTECTION: ENABLED"... Can influence somthing this thing??
Thanks
Click to expand...
Click to collapse
put your rom file in odin in (ap)....you can download your rom from sammobile.and try again try the metode up
RoyaLKurTx3 said:
Be careful when you format system, it's dangerous and the only fix for it is flashing a ROM.
Try these:
1. Download this and extract the files in the ZIP: http://www.sammobile.com/firmwares/download/40040/I9195XXUCNK4_I9195OXXCNK5_SEE.zip/
2. You should get 2 files;
I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5
SS_DL.dll
Ignore the SS_DL.dll. You will use the other file.
3. Go to Odin and thick only 'Auto Reboot' and 'F. Reset Time'. Now Insert the .tar.md5 I named above in the AP place.
4. Turn off your phone and boot into recovery. Clear data and cache. Now restart to download mode.
5. If you are asked to continue or to cancel and restart phone, choose continue.
6. Keep your phone like that and check that you have this (or similar) layout in Odin;
Now press start and wait until everything have finished and your phone boots (May take 8-11 minutes) If you followed these steps and you got a fail, then you must have done something wrong or your phone has something wrong in terms of hardware. Good Luck mate.
Click to expand...
Click to collapse
Hi,
i tried also this... Odin says:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
... i'm little bit disperate...
You inserted a modem.tar.md5 not the file I told you.
atlantis87 said:
Hi,
i tried also this... Odin says:
<ID:0/003> Removed!!
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> modem.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> NON-HLOS.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003> Receive Response from boot-loader
<OSM> All threads completed. (succeed 0 / failed 1)
... i'm little bit disperate...
Click to expand...
Click to collapse
dont be afraid my friend this is simple...so dont put the file in the modem pit it at (ap) colone...try a difirent odin v 3.09 okey ..dont missed to extract the zip file for your file rom okey and gry again
RoyaLKurTx3 said:
You inserted a modem.tar.md5 not the file I told you.
Click to expand...
Click to collapse
Sorry, i wrongly paste the odin row... The follow row are the correct...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
atlantis87 said:
Sorry, i wrongly paste the odin row... The follow row are the correct...
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9195XXUCNK4_I9195OXXCNK5_I9195XXUCNK4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> sbl1.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl2.mbn
<ID:0/003> sbl3.mbn
<ID:0/003> aboot.mbn
<ID:0/003> rpm.mbn
<ID:0/003> tz.mbn
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img.ext4
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Try everything again on a different computer, if you can.
RoyaLKurTx3 said:
Try everything again on a different computer, if you can.
Click to expand...
Click to collapse
Ok, thanks... i made all these trial on a macbook using vmware fusion with windows 8. I can try on another mac (with vmware and windows 8)... Do you think that can be work with another mac or is necessary to try with a pc?
atlantis87 said:
Ok, thanks... i made all these trial on a macbook using vmware fusion with windows 8. I can try on another mac (with vmware and windows 8)... Do you think that can be work with another mac or is necessary to try with a pc?
Click to expand...
Click to collapse
Try using windows.
RoyaLKurTx3 said:
Try using windows.
Click to expand...
Click to collapse
i tried and.... it works! However wifi and mobile network don't work. Do you have any other suggestion?
Thanks
RoyaLKurTx3 said:
Try using windows.
Click to expand...
Click to collapse
Maybe i found something... My IMEI is null... and i don't have a backup...
Our daughter deleted all of the pics on my wife's phone. She tried to use Dr. Fone, but someone told us that it failed because her phone wasn't rooted. So I tried to root it from this post on cnet:
It failed during the root. Now it says "Firmware upgrade encountered an issue. Please select recovery mode in Kies and try again. Which I tried and also failed.
After a lot of heart ache and hours working on it, i have what a friend told me was the right tar file. I have attached the error in Odin.
When I run the tar file in Odin here is what the output screen shows:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCDLK3_I747ATTDLK3_I747UCDLK3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> aboot.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Then my phone screen show this:
SW REV CHECK FAIL : Fused 3 > Binary 0
Not really my area of expertise at all. Any help would be appreciated!!
Thanks,
Brian
You cannot flash that tar file onto your phone. It is failing because that file is trying to downgrade the bootloader.
I recommend not flashing anymore files until you know the bootloader version of your phone.
I recommend you flash the latest Philz Touch custom recovery using desktop Odin from here:https://goo.im/devs/philz_touch/CWM_Advanced_Edition/d2lte/
Use Philz to flash the latest CM11 and Gapps. Then install the Samsung Phone Info app from the play store to verify your bootloader.
Once you know your bootloader, let us know the version.
I've searched high, and I've search low for firmware for my phone (only to be led to sites whose download speed is atrocious).
My phone model is: SM-N910P
I've been searching for the .tar files for the firmware updates. The MD5 is either not valid by Odin's standard or something else.
Can someone point me along to a link of the latest Note 4 Stock Firmware update from a site that doesn't take all day to download from? Thanks Kindly.
P.s. Yes, I have gone through website and threads posting link to the correct firmware but all of them have not been MD5 correct or worked at all.
I'm also experiancing frequent crashes/restarts on the phone.
I got this phone from a family friend and its been acting weird in ways that are outside my comphrenension. It's rooted and they need it to factory state but all theses errors, problems, slow downloads, are making it near impossible.
Try downloading stock tar from this thread with your PC. You can and should verify the md5 before flashing in Odin when md5 is provided.
http://forum.xda-developers.com/showthread.php?p=63868221
Sent from my SM-N930P using Tapatalk
I flashed the file you linked to and this is what i got in Odin
<ID:0/009> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/009> Odin engine v(ID:3.1101)..
<ID:0/009> File analysis..
<ID:0/009> SetupConnection..
<ID:0/009> Initialzation..
<ID:0/009> Get PIT for mapping..
<ID:0/009> Firmware update start..
<ID:0/009> SingleDownload.
<ID:0/009> aboot.mbn
<ID:0/009> NAND Write Start!!
<ID:0/009> sbl1.mbn
<ID:0/009> rpm.mbn
<ID:0/009> tz.mbn
<ID:0/009> sdi.mbn
<ID:0/009> NON-HLOS.bin
<ID:0/009> boot.img
<ID:0/009> recovery.img
<ID:0/009> system.img.ext4
<ID:0/009> FAIL! (Write)
<ID:0/009>
<ID:0/009> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
gordonfrohman said:
I flashed the file you linked to and this is what i got in Odin
Added!!
Enter CS for MD5..
Check MD5.. Do not unplug the cable..
Please wait..
Checking MD5 finished Sucessfully..
Leave CS..
Odin engine v(ID:3.1101)..
File analysis..
SetupConnection..
Initialzation..
Get PIT for mapping..
Firmware update start..
SingleDownload.
aboot.mbn
NAND Write Start!!
sbl1.mbn
rpm.mbn
tz.mbn
sdi.mbn
NON-HLOS.bin
boot.img
recovery.img
system.img.ext4
FAIL! (Write)
Complete(Write) operation failed.
All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
Questions:
Which stock tar did you flash? (see end of this post)
Does the phone frequently reboot or boot to download mode (reporting) failure to normal boot? Any eMMC failures reported?
Things to check or try if non applicable:
Factory reset in stock recovery if no OS is installed. If you can boot OS, make sure that Settings/Security/reactivation lock is disabled and enable developer mode and enable USB debugging.
Verify correct Samsung driver installed on PC or uninstall and reinstall from Samsung support for Note 4.
Use original Samsung Note 4 cable or replace. A good quality USB data cable should work but if replacing, use OEM replacement.
Run Odin in administrative mode. Try the suggested Odin version (3.10.7 or 3.10.6) or latest version from here: http://forum.xda-developers.com/showpost.php?p=51767811&postcount=1
(Odd reported issues sometimes result in one of these reported as successful where various others weren't).
Try another USB port, cable or PC
Edit: All KIES and Smart Switch sessions should be killed prior to starting Odin session.
Do not Odin older stock tars; usable stock tars start at OG5 and up.
Sent from my SM-N930P using Tapatalk