I edited /system/etc/mixer_paths_qcwcn.xml to make the volume louder, and I forgot to change the permissions back, so now it's stuck on a bootloop.
What are my options now to get the phone back ? I'd rather now reset, wouldn't that make me lose stuff on the built in 16gb partition ? (i.e photos)
I'm running a UK D855 16GB and I was on v10a-EUR-xx , which was bought in carphone warehouse (but on o2 with no branding)
Am I stuck having to install a kdz with the LG tool ? and if so, which one should I use for this model ? and should I go to a higher version ? I saw 10g was available, but I'm not sure whether to go straight to that or not.
Is it possible to get in and repair the permissions ??
mjb152 said:
I edited /system/etc/mixer_paths_qcwcn.xml to make the volume louder, and I forgot to change the permissions back, so now it's stuck on a bootloop.
What are my options now to get the phone back ? I'd rather now reset, wouldn't that make me lose stuff on the built in 16gb partition ? (i.e photos)
I'm running a UK D855 16GB and I was on v10a-EUR-xx , which was bought in carphone warehouse (but on o2 with no branding)
Am I stuck having to install a kdz with the LG tool ? and if so, which one should I use for this model ? and should I go to a higher version ? I saw 10g was available, but I'm not sure whether to go straight to that or not.
Is it possible to get in and repair the permissions ??
Click to expand...
Click to collapse
Yes, u can do it lg g2 flash rom stock instruction. It's tha same, if u choose normal flash it will fix the permission.
yossitay1 said:
Yes, u can do it lg g2 flash rom stock instruction. It's tha same, if u choose normal flash it will fix the permission.
Click to expand...
Click to collapse
I struggled to find the right kdz file , so I ended up with the LG pc tools, I typed in my IMEI and S/N and stuck the phone in download mode. It detected it, and then upgraded my firmware from 10a to 10e, so now I'm upgraded and it boots fine. Just got to apply ioroot now and then not make that stupid mistake again !
mjb152 said:
I edited /system/etc/mixer_paths_qcwcn.xml to make the volume louder, and I forgot to change the permissions back, so now it's stuck on a bootloop.
What are my options now to get the phone back ? I'd rather now reset, wouldn't that make me lose stuff on the built in 16gb partition ? (i.e photos)
I'm running a UK D855 16GB and I was on v10a-EUR-xx , which was bought in carphone warehouse (but on o2 with no branding)
Am I stuck having to install a kdz with the LG tool ? and if so, which one should I use for this model ? and should I go to a higher version ? I saw 10g was available, but I'm not sure whether to go straight to that or not.
Is it possible to get in and repair the permissions ??
Click to expand...
Click to collapse
This just happened to me.. Good thing I made a backup before.. If you did also or still have a rom on your SD card follow these instructions for the future..
Power off your device and wait for 5-10 seconds until the device is fully switched off or do a battery pull.
Press and hold ‘Volume Down + Power’ buttons together and release them as soon as you see the LG logo on your phone’s screen.
Now immediately press and hold the ‘Volume Down + Power’ buttons again until you see the ‘Hard reset screen’
Go down to yes on hard reset... Press power button once, and then again to confirm hard reset. If you have a custom recovery installed, your phone won’t hard reset and will boot into recovery mode.
If I had a custom recovery I would have made a backup, trouble is I'm on a European 855 with a locked bootloader, so waiting that be unlocked before i get twrp on there. I know there is a tethered method, but I'm in 2 minds whether to go down that route.
Related
after i press power button + vol+ button, it show "download mode is disabled by killswitch", i just put the correct pin to Mcafee but it still show the same message, please help, thank you
F400S
4.4.2 (can not update to 5.0 by OTA / PC Suite:crying
Have you tried to root your phone and remove McAfee completely? That was the first thing that I did on my F400S and F460S.
nothing to cheer up
i also have the same model and "it" also does not go into recovery , i am though able to get it into download, - first load your lg driver and make sure your port is 41 under device manager, once in 41 you can use the flashtool to upload but ONLY A KDZ FILE , that's as much as i got from this site. (btw there is a lollipop kdz file for the k400 floating around, you can use it to flash lollipop but it isn't rooted - i can find the link and if you're successfull at getting lollipop to root with these 2 files, i will really appreciate you help - email me)
the volume down + power just don't work
try pressing volume down + power + volume up and when logo shows up let go volume up for less than a second and let me know if you can decipher the korean page.
this korean page has 3 options but all of them lead to Reboot System., i don't read korean and no one volunteered help.
Also with the phone working i loaded CWM recovery and with it running i was able to flash a lollipop zip file for F400 but this file is not rooted and i couldn't root it so i reflashed back to an older kitkat version
if you're luckier than me, i would appreciate you letting me know how you were able to load the lollipop and root it afterward.
sincerely
poorpoorpoor said:
after i press power button + vol+ button, it show "download mode is disabled by killswitch", i just put the correct pin to Mcafee but it still show the same message, please help, thank you
F400S
4.4.2 (can not update to 5.0 by OTA / PC Suite:crying
Click to expand...
Click to collapse
Pilz said:
Have you tried to root your phone and remove McAfee completely? That was the first thing that I did on my F400S and F460S.
Click to expand...
Click to collapse
i tried stump root and activate su, however the system do not allow to remove Mcafee even rooted, maybe my procedure is wrong as i am a newbie on this :laugh:
exlaval said:
i also have the same model and "it" also does not go into recovery , i am though able to get it into download, - first load your lg driver and make sure your port is 41 under device manager, once in 41 you can use the flashtool to upload but ONLY A KDZ FILE , that's as much as i got from this site. (btw there is a lollipop kdz file for the k400 floating around, you can use it to flash lollipop but it isn't rooted - i can find the link and if you're successfull at getting lollipop to root with these 2 files, i will really appreciate you help - email me)
the volume down + power just don't work
try pressing volume down + power + volume up and when logo shows up let go volume up for less than a second and let me know if you can decipher the korean page.
this korean page has 3 options but all of them lead to Reboot System., i don't read korean and no one volunteered help.
Also with the phone working i loaded CWM recovery and with it running i was able to flash a lollipop zip file for F400 but this file is not rooted and i couldn't root it so i reflashed back to an older kitkat version
if you're luckier than me, i would appreciate you letting me know how you were able to load the lollipop and root it afterward.
sincerely
Click to expand...
Click to collapse
Thank you for your help, i tried flashtool already but it doesn't work, the phone reboot during the updating , it show "the message" and go back to normal boot after that, i tried many times already:crying:
Hi there...i got a problem with my lg..what actually i hve done is that i switched my mobile in recovery mode and i wiped data,chache and also go to mount menu then does my mechanicy i dont knw what to do nw... its not taking start now
i think i need to chng its software nw
ZaibShah said:
Hi there...i got a problem with my lg..what actually i hve done is that i switched my mobile in recovery mode and i wiped data,chache and also go to mount menu then does my mechanicy i dont knw what to do nw... its not taking start now
i think i need to chng its software nw
Click to expand...
Click to collapse
Um, if its not starting at all (no boot logo etc) then that would be a hard brick. Google should bring up plently of results. It may be a softbrick (can easily be fixed by restoring to stock firmware using lg flash tool or a back up). So does it display the lg logo?
Did you install the Rom after wiping? What is the exact process you were going through and what was your intended end result?
Today I was trying to install a custom rom, but I messed it up and had to reset it to stock rom.
After that I reseted it back to stock rom, I rooted my phone with Kingroot and used this app: https://play.google.com/store/apps/details?id=b007.autorecd855 to install recovery. After that I powered off my phone and now it won't turn on. Already removed battery a plenty of times, when putting in the charger nothing happens, pc won't see it also.
The only moment when my phone lights up is when I remove my battery and put it in the charger, then it basically says that it's charging but with no battery in it. Also when removing the battery and connecting to my pc it only sees it as a unrecognizable device.
Suggestions on what I can do? IF not, poor me, gonna buy a new smartphone then.
Btw, I still have some garanty. Maybe it's worth sending it to the support services.
Extra info:
g3 d855
You used wrong autorec install LP recovery to MM. Download MM version autorec from LG G3 Xda forum. Try flash back to stock or something else. Instructions are in LG G3 Xda forum if you search more. Sorry.
pjadec said:
You used wrong autorec install LP recovery to MM. Download MM version autorec from LG G3 Xda forum. Try flash back to stock or something else. Instructions are in LG G3 Xda forum if you search more. Sorry.
Click to expand...
Click to collapse
Hmm, I was really sure that I used the right one.
Anyway, how can I flash it again if I can't even get the lg logo to show, neither get him in download mode or that my pc recognises him?
Btw, I still have some garanty. Maybe it's worth sending it to lg.
If you have no access to any recovery mode, Fastboot or download mode.then use the method of Qualcomm 9008.btw your warranty is void because you have rooted device and messed with it.
RobinHood_3 said:
Hmm, I was really sure that I used the right one.
Anyway, how can I flash it again if I can't even get the lg logo to show, neither get him in download mode or that my pc recognises him?
Btw, I still have some garanty. Maybe it's worth sending it to lg.
Click to expand...
Click to collapse
I also had same issue and I'm also sure that I used the correct Autorec version.
I sent the phone to LG because the warranty is still valid.
I know how to fix this
RobinHood_3 said:
Today I was trying to install a custom rom, but I messed it up and had to reset it to stock rom.
After that I reseted it back to stock rom, I rooted my phone with Kingroot and used this app: https://play.google.com/store/apps/details?id=b007.autorecd855 to install recovery. After that I powered off my phone and now it won't turn on. Already removed battery a plenty of times, when putting in the charger nothing happens, pc won't see it also.
The only moment when my phone lights up is when I remove my battery and put it in the charger, then it basically says that it's charging but with no battery in it. Also when removing the battery and connecting to my pc it only sees it as a unrecognizable device.
Suggestions on what I can do? IF not, poor me, gonna buy a new smartphone then.
Btw, I still have some garanty. Maybe it's worth sending it to the support services.
Extra info:
g3 d855
Click to expand...
Click to collapse
i remember after 1 day of having this phone this happened this was likely caused by having the latest boot loader i remember this because i fresh installed the marshmallow kdz after that i installed autorec mm it told me to restart and my phone died there, however after spending 8 hours straight i found a solution the smart boot diagnostics tool can write an older version of the boot loader understand that your phone must be in the qdloader9008 mode, if your PC doesn't detect the phone make sure you install the drivers in the zip from the download install the 32 bit if on 32 bit system or install 64 bit on 64 bit system. Hey if you need assistance on doing this Download team viewer and i'll be more than welcome to help unbrick our d855
http://www.4shared.com/postDownload/jACBEo-zba/SmartBootDiagv131_Oversea_SVC_.html
Hello, (complete n00b here)
Several days ago I've tried to flash a 6.0 MM (from 5.1) to my LG G4 H815 phone. There was no option to do it automatically so I proceded to do it manually via flashboot.
I hard-bricked it to oblivion as in black screen, no response whatsoever.
While investigating @ the internet I've managed to understand I could get it fixed via quadcomm drivers (mode 9008).
Tried various "fixes" for H815 but was getting safari download errors. For some reason I tried a LS991 fix and it worked. When I started the phone it showed no logo but just a secure booting error 1006.
Still, could enter firmware download so I began to flash a lot of KDZ firmwares with no success.
LGUP shows my model : H81510H.
While in fastboot mode there is a note below (wasn't there the first time) with codes : 633 B46 or something like that.
While flashing anything it ALWAYS STOPS at 9% with a tot anti-rollback error. While flashing the code changes briefly where one can read smth like : LGLS991ZVA ver. 6.0
Managed to download some KDZ for that exact model, SAME ERROR. Tried to find / flash LS991ZVA with no success in finding a TOT file.
Also, managed to get ADB drivers up and it shows unauthorized in listing (LS991). Fastboot does not detect my device even in fastboot mode @ phone.
Please HELP!
Longbranch said:
Hello, (complete n00b here)
Several days ago I've tried to flash a 6.0 MM (from 5.1) to my LG G4 H815 phone. There was no option to do it automatically so I proceded to do it manually via flashboot.
I hard-bricked it to oblivion as in black screen, no response whatsoever.
While investigating @ the internet I've managed to understand I could get it fixed via quadcomm drivers (mode 9008).
Tried various "fixes" for H815 but was getting safari download errors. For some reason I tried a LS991 fix and it worked. When I started the phone it showed no logo but just a secure booting error 1006.
Still, could enter firmware download so I began to flash a lot of KDZ firmwares with no success.
LGUP shows my model : H81510H.
While in fastboot mode there is a note below (wasn't there the first time) with codes : 633 B46 or something like that.
While flashing anything it ALWAYS STOPS at 9% with a tot anti-rollback error. While flashing the code changes briefly where one can read smth like : LGLS991ZVA ver. 6.0
Managed to download some KDZ for that exact model, SAME ERROR. Tried to find / flash LS991ZVA with no success in finding a TOT file.
Also, managed to get ADB drivers up and it shows unauthorized in listing (LS991). Fastboot does not detect my device even in fastboot mode @ phone.
Please HELP!
Click to expand...
Click to collapse
H81510h is os version it is still at 5.1 I think....what may help is plug your phone in with lgup and drop the battery out of it then closes of LG up put battery back in and start LG up and find kdz that matchs your phone and make sure that it doesn't have anti rollback.....
stinka318 said:
H81510h is os version it is still at 5.1 I think....what may help is plug your phone in with lgup and drop the battery out of it then closes of LG up put battery back in and start LG up and find kdz that matchs your phone and make sure that it doesn't have anti rollback.....
Click to expand...
Click to collapse
Hello and thx for reply. I tried to do what u've said. It did something (I was looking for a while back). When I plug the cable back in, my windows 7 immediately installs quadcomm hs-usb driver (9008) and my phone acts as if it was dead. LGUP cannot find it in that state. I've been trying to QFIL the "proper" soft but it continues to pop different errors (using different QFIL versions). Either saharafail or some sort of download fail.
LGUP still presents an error (if I decide to "fastboot" it) @ 9% 0x2000, TOT antirollback version is smaller than device version.
How can I make sure I've got the proper KDZ without ANTI-ROLLBACK?
Longbranch said:
Hello and thx for reply. I tried to do what u've said. It did something (I was looking for a while back). When I plug the cable back in, my windows 7 immediately installs quadcomm hs-usb driver (9008) and my phone acts as if it was dead. LGUP cannot find it in that state. I've been trying to QFIL the "proper" soft but it continues to pop different errors (using different QFIL versions). Either saharafail or some sort of download fail.
LGUP still presents an error (if I decide to "fastboot" it) @ 9% 0x2000, TOT antirollback version is smaller than device version.
How can I make sure I've got the proper KDZ without ANTI-ROLLBACK?
Click to expand...
Click to collapse
This may help........
https://forum.xda-developers.com/lg-g5/development/uppercut-lgup-loader-g5-variants-t3511295
stinka318 said:
This may help........
https://forum.xda-developers.com/lg-g5/development/uppercut-lgup-loader-g5-variants-t3511295
Click to expand...
Click to collapse
Thx again. Uppercut shows H81510H as LGUP did. Is it possible that it's somehow write-protected?
It confuses me, since during the firmware update on my phone, I get this small box below the picture showing wierd codes : 633A Bxx and when I'm trying to flash my phone, the code gets longer with LS991ZVA v6.0 and more other. It then stops.
Funny thing is, when I got the phone I couldn't even connect to the LG bridge to update it at all. I've managed to do it bugging the MTP protocol but THAT on the other hand prevented me from copying stuff / FLASH my phone to MM 6.0. Had to factory reset it back then and all went back to "normal" = LG couldnt detect my device but I could copy photos or stuff from it.
NOW, when my phone is bricked, LGbridge DETECTS my phone (in fastboot), downloads the newest KDZ update BUT cannot install it (same thing as in LGUP). Hence my question : is it somehow write-protected?
Longbranch said:
Thx again. Uppercut shows H81510H as LGUP did. Is it possible that it's somehow write-protected?
It confuses me, since during the firmware update on my phone, I get this small box below the picture showing wierd codes : 633A Bxx and when I'm trying to flash my phone, the code gets longer with LS991ZVA v6.0 and more other. It then stops.
Funny thing is, when I got the phone I couldn't even connect to the LG bridge to update it at all. I've managed to do it bugging the MTP protocol but THAT on the other hand prevented me from copying stuff / FLASH my phone to MM 6.0. Had to factory reset it back then and all went back to "normal" = LG couldnt detect my device but I could copy photos or stuff from it.
NOW, when my phone is bricked, LGbridge DETECTS my phone (in fastboot), downloads the newest KDZ update BUT cannot install it (same thing as in LGUP). Hence my question : is it somehow write-protected?
Click to expand...
Click to collapse
Have you tried to eset it by pushing power and volume own then when you see bootsplash then release power button and hen quickly push the power button again....
But in your case push power and volume down within the count or 20 then release power then push power button again and see what happens and then try the same thing on volume up......
Thanks for the reply.
I did what u've said. Despite no logo I tried to release power button for a second just after the screen's brightness goes up (I also get a small vibration @ start). Everytime I get secure booting error 1006 after a few seconds.
On the other hand when I did that with volume UP button there was no error but there was nothing aswell until I release power button in which case I got the secure booting error. All of the above tries were done with no USB connection with anything.
Longbranch said:
Thanks for the reply.
I did what u've said. Despite no logo I tried to release power button for a second just after the screen's brightness goes up (I also get a small vibration @ start). Everytime I get secure booting error 1006 after a few seconds.
On the other hand when I did that with volume UP button there was no error but there was nothing aswell until I release power button in which case I got the secure booting error. All of the above tries were done with no USB connection with anything.
Click to expand...
Click to collapse
Do try with usb s well it may do something r do nothing......
Can't tell atm since I gave it to professionals. I'll wait and see how it'll turn up. Thx for all the effort tho, was nice to tinker with a lil help
@Longbranch did you solve this problem ? I'm in the same state but my phone model is H810, everything else is the same as yours.
Nope, not really. I gave it back to the reseller and my money got returned luckily.
The professionals I refer to above did install a specific firmware for the ls991 type. Firmware ZVB I think. The only one appliable apparently. Anyways, as I suspected the ls991 type is for the US and therefore it didn't work in my country in EU. My sim card wouldnt work with it. Besides, without the sim card, the phone decided to freeze and die after several minutes every time I turn it on. Swapped for LG G5 and it's working flawlessly up until this day.
good for you, what i don't understand is that it's a h810 model but now identify as ls991 does that mean you can convert it just by a Qfil flash? I may try another model flash if can't find a suitable Rom for it
Longbranch said:
Nope, not really. I gave it back to the reseller and my money got returned luckily.
The professionals I refer to above did install a specific firmware for the ls991 type. Firmware ZVB I think. The only one appliable apparently. Anyways, as I suspected the ls991 type is for the US and therefore it didn't work in my country in EU. My sim card wouldnt work with it. Besides, without the sim card, the phone decided to freeze and die after several minutes every time I turn it on. Swapped for LG G5 and it's working flawlessly up until this day.
Click to expand...
Click to collapse
Chebhou said:
good for you, what i don't understand is that it's a h810 model but now identify as ls991 does that mean you can convert it just by a Qfil flash? I may try another model flash if can't find a suitable Rom for it
Click to expand...
Click to collapse
Yes! That's what I and neutrondev telling everyone :
do not use qfil without the knowledge about the result!
The only working firehose file available out there is for the ls991 and that means if you use it it will turn your device into a ls991 without any way to get back to your previous device model!!
.
Sent from my LG-H815 using XDA Labs
@steadfasterX since I have done it already is there any way to get it working even as an LS991 ?
here is what i did till now
the reason for using Qfill is that it went dead after flashing an H810 rom .
after that when it's in download mode it doesn't allow me to flash the ls911ZV5 ls911ZV6 ls911ZV6_12 roms that i found ( it says LS991ZVA )
so i went in fastboot and flashed boot/aboot/recovery....img extracted from the ls911ZV6 rom then it accepted the rom in download mode
but it is stuck in a hard bootloop ( reboots when it is getting in recovery but still has download mode yet no fastboot as before)
any thoughts ?
Chebhou said:
@steadfasterX since I have done it already is there any way to get it working even as an LS991 ?
here is what i did till now
the reason for using Qfill is that it went dead after flashing an H810 rom .
after that when it's in download mode it doesn't allow me to flash the ls911ZV5 ls911ZV6 ls911ZV6_12 roms that i found ( it says LS991ZVA )
so i went in fastboot and flashed boot/aboot/recovery....img extracted from the ls911ZV6 rom then it accepted the rom in download mode
but it is stuck in a hard bootloop ( reboots when it is getting in recovery but still has download mode yet no fastboot as before)
any thoughts ?
Click to expand...
Click to collapse
Yes it's possible. You can boot a h811 H815 or any other rom you like. Even LOS!!
Great right? BUT you are bounded to the ls991 modem and so you need to be in a sprint network to use telephony. That means the phone is now useless outside the US .
And you wrote you tried ls911 ROMs? I hope you meant ls991
I work on a fully working experience on every network though. Checkout my proof of concept for unlocking the bootloader thread
I can go into details on IRC if you like.
..
Sent from my LG-H815 using XDA Labs
@steadfasterX thank you for keeping up with me ! ( btw what room on IRC ?)
for now I have used Qfill again and got fastboot working again and flashed TWRP ( not sure where ! ) so when the phone is off and i plug the usb it boots to twrp ( but it doesn't in recovery )
normal boot will show "secure boot error 1002"
then i flashed twrp img to recovery partition using twrp but it didn't work in recovery ( still reboots after showing Recovery Mode loading screen )
also tried to load some roms on the device to try them but I got error "file too large for filesystem " when copying them .
atm I don't know the state I'm in and what should be next ?
btw here are the recovery log and dmesg
Chebhou said:
@steadfasterX thank you for keeping up with me ! ( btw what room on IRC ?)
for now I have used Qfill again and got fastboot working again and flashed TWRP ( not sure where ! ) so when the phone is off and i plug the usb it boots to twrp ( but it doesn't in recovery )
normal boot will show "secure boot error 1002"
then i flashed twrp img to recovery partition using twrp but it didn't work in recovery ( still reboots after showing Recovery Mode loading screen )
also tried to load some roms on the device to try them but I got error "file too large for filesystem " when copying them .
atm I don't know the state I'm in and what should be next ?
btw here are the recovery log and dmesg
Click to expand...
Click to collapse
Np we can bring you back to life but as already said without cell service. That's the price for the firehose and unlocked feeling you have now.
Did you found and read my thread here?
https://forum.xda-developers.com/g4/general/bl-unlock-unlock-bootloader-proof-t3648288
There you will find some more info and also the IRC details how you can find me. I'm online from Monday to Friday mainly.
It's much easier to talk in chat then here. once all the details are known I will provide a full guide.
.
Sent from my LG-H815 using XDA Labs
Hi Everyone.
I'm in a big mess.
My LG G4 showed as H815 in device information (But it was F500L) . It had 5.1 (LP).
To update it to 7.0 (N) I flashed the TOT file for N with version H815 thru LG UP.
Now it did complete to 100%. The phone rebooted and showed error like " Central App not loded" or something like this.
I tried again to Flash the TOT file thru LG Up. It went till 21% then shoed error command not recognized.
I triedLG bridge. It shows device as F500L.
Although LG Bridge says update available, it could not update either.
So the problem is I flashed wrong version. My phone is F500L and its showing "firmware update" when plugged into USB with PC.
In LG Up it shows as H81510H
Please guide friends....
frend2001 said:
Hi Everyone.
I'm in a big mess.
My LG G4 showed as H815 in device information (But it was F500L) . It had 5.1 (LP).
To update it to 7.0 (N) I flashed the TOT file for N with version H815 thru LG UP.
Now it did complete to 100%. The phone rebooted and showed error like " Central App not loded" or something like this.
I tried again to Flash the TOT file thru LG Up. It went till 21% then shoed error command not recognized.
I triedLG bridge. It shows device as F500L.
Although LG Bridge says update available, it could not update either.
So the problem is I flashed wrong version. My phone is F500L and its showing "firmware update" when plugged into USB with PC.
In LG Up it shows as H81510H
Please guide friends....
Click to expand...
Click to collapse
Why u flashed the tot file?
For your Location (Korea ? ) there is an official Update to 7....
Look here: https://lg-firmwares.com/lg-f500l-firmwares/
or this Link: https://lg-kdz-firmware.com/
You should use LGUP again and flash back with stock 5.1 or 6.0 kdz, follow the link.
Hope will helps you otherwise reply
Foto-AG said:
Why u flashed the tot file?
For your Location (Korea ? ) there is an official Update to 7....
You should use LGUP again and flash back with stock 5.1 or 6.0 kdz, follow the link.
Hope will helps you otherwise reply
Click to expand...
Click to collapse
Thanks for your response
LG UP now shows my device as H815. I tried flashing L500F kdz but got error at 11% "Invalid command response"
Now what to do ?
frend2001 said:
Thanks for your response
LG UP now shows my device as H815. I tried flashing L500F kdz but got error at 11% "Invalid command response"
Now what to do ?
Click to expand...
Click to collapse
Okay, that Sounds good Yes really..
I think the Probelm is in LGUP´s dll, you must replace the LGUP_8994.dll with the L500F kdz from.
Download the Tool LG Firmware extract, Link from my GDrive:
https://drive.google.com/file/d/1NTzwI-qLBpIgTov5PC4THZJWbAOhJDO3/view?usp=sharing
Start the tool and load the kdz in, then you see some files in the tool. Mark the lgup8994.dll and extract it, close the tool.
The dll can find now in the Folder of LG Firmware extract tool, rename it to LGUP_8994.dll
Copy that new dll and put into C:\Program Files\LG Electronics\LGUP\model\8994
The old LGUP_8994.dll remove to desktop and put the new dll in here and start again with LGUP.
Please point LGUP to Refurbish and NOT to Upgrade. The old dll that was in the Folder is for the Nougat tot file and the H81520p kdz only.
Hopefully thats will works for you, normaly it should !
Foto-AG said:
Okay, that Sounds good Yes really..
I think the Probelm is in LGUP´s dll, you must replace the LGUP_8994.dll with the L500F kdz from.
Download the Tool LG Firmware extract, Link from my GDrive:
https://drive.google.com/file/d/1NTzwI-qLBpIgTov5PC4THZJWbAOhJDO3/view?usp=sharing
Start the tool and load the kdz in, then you see some files in the tool. Mark the lgup8994.dll and extract it, close the tool.
The dll can find now in the Folder of LG Firmware extract tool, rename it to LGUP_8994.dll
Copy that new dll and put into C:\Program Files\LG Electronics\LGUP\model\8994
The old LGUP_8994.dll remove to desktop and put the new dll in here and start again with LGUP.
Please point LGUP to Refurbish and NOT to Upgrade. The old dll that was in the Folder is for the Nougat tot file and the H81520p kdz only.
Hopefully thats will works for you, normaly it should !
Click to expand...
Click to collapse
Well this is not working.
LG UP recognizes my phone as H81529a. So it doesn;t let me flash F500L rom.
When I extracted 3994 DLL from F500L KDZ and replace in LGUP folder and start LG UP. It shouts wrong version DLL.
Is there any way I can make LG UP to recognize my device as F500L and Not H81529a.
LG Bridge recognizes it as F500L though but it doesn't update my phone either.
Please help n guide
frend2001 said:
Well this is not working.
LG UP recognizes my phone as H81529a. So it doesn;t let me flash F500L rom.
When I extracted 3994 DLL from F500L KDZ and replace in LGUP folder and start LG UP. It shouts wrong version DLL.
Is there any way I can make LG UP to recognize my device as F500L and Not H81529a.
LG Bridge recognizes it as F500L though but it doesn't update my phone either.
Please help n guide
Click to expand...
Click to collapse
Hmmmmmm
Okay, the H81529a Header says LGUP that is a G4 H815 with Anroid 7 ( 29a) on it. Okay, the LGUP_3994.dll wont work for your F500L kdz. By the Way..wich kdz you try to flash? is it a MM one or the Korean Nougat ?
On my H815 i had the 29a after flashing the Nougat tot file too and came back to MM ONLY with H81520p_00_0314.kdz other kdz for my H815 did fail too.
This Problem with LGUP is only the dll file...so you must find a working dll for LGUP.
Maybe you download the Korean Nougat kdz and extract the dll like the last posting before and flash the Korean Nougat, i think the Korean Nougat has 29a too, so LGUP should work.....
Or find a F500L20p kdz file...
I don´t know what to do yet. Sorry.
Foto-AG said:
Hmmmmmm
Okay, the H81529a Header says LGUP that is a G4 H815 with Anroid 7 ( 29a) on it. Okay, the LGUP_3994.dll wont work for your F500L kdz. By the Way..wich kdz you try to flash? is it a MM one or the Korean Nougat ?
On my H815 i had the 29a after flashing the Nougat tot file too and came back to MM ONLY with H81520p_00_0314.kdz other kdz for my H815 did fail too.
This Problem with LGUP is only the dll file...so you must find a working dll for LGUP.
Maybe you download the Korean Nougat kdz and extract the dll like the last posting before and flash the Korean Nougat, i think the Korean Nougat has 29a too, so LGUP should work.....
Or find a F500L20p kdz file...
I don´t know what to do yet. Sorry.
Click to expand...
Click to collapse
Well...
I have been able to sucessfully flash H81520p_00_0314.kdz on it.
It starts but no signal / network.
I'm from India so I think the version I flashed doesn't match with Indian Band.
Now what to do ?
In India following works :
2G network GSM 850 / 900 / 1800 / 1900 MHz
3G network HSDPA 850 / 900 / 1900 / 2100|TD-SCDMA
4G network LTE band 1(2100), 3(1800), 7(2600), 38(2600), 39(1900), 40(2300), 41(2500)
Data GPRS,EDGE,HSDPA,HSUPA,HSPA,HSPA+,LTE
frend2001 said:
Well...
I have been able to sucessfully flash H81520p_00_0314.kdz on it.
It starts but no signal / network.
I'm from India so I think the version I flashed doesn't match with Indian Band.
Now what to do ?
In India following works :
2G network GSM 850 / 900 / 1800 / 1900 MHz
3G network HSDPA 850 / 900 / 1900 / 2100|TD-SCDMA
4G network LTE band 1(2100), 3(1800), 7(2600), 38(2600), 39(1900), 40(2300), 41(2500)
Data GPRS,EDGE,HSDPA,HSUPA,HSPA,HSPA+,LTE
Click to expand...
Click to collapse
For my undstanding....
1) You have still H81520p_00_0314.kdz running on your Phone ? but no Indian Band ?
2) What Header is LGUP showing now?
If you have H81520p_00_0314.kdz on it, you are able to Downgrade to ever Version you want, H81520p_00_0314.kdz make it possible only !
So, find out your Rom for your Location and flash it with LGUP. Keep the 8994 dll it comes from H81520p_00_0314.kdz in the folder and flash.
After downgrade with LGUP (Refurbish Mod ) do a Over the Air update on your Phone or via LG Bridge and do "correct update Error" instead of "Search for Updates" and normaly its works.
Follow this Links for the Roms
http://storagecow.eu/index.php?dir=Xda/
https://lg-kdz-firmware.com/
If you are unsure what rom you must get, go to https://lg-firmware-rom.com/
and type your IMEI in and watch for the results.
Greetings....
Well
Problems just dont seem to end.
I hooked it up with LG bridge.
It showed model as "G4".
No version no code just G4.
I started to update it (thats before I read your msg)
Update stopped in between and phone turned off. I unplugged it and pulled out the battery. Restarted.
It showed LG logo and agained turned off.
I tried to reset by pressing Down vol n power button.
Options came to reset n I reset it.
Now again turned on. It showed optimizing android.
Stopped at 4 of 32 app and screen went blank.
Now LG bridge reads it as L500F at place of G4.
Hooked up again in download mode and LG UP disnt recognize it. Again restarted.
LG up recognized as H81520p.
I reflashed thr H815 20 p kdz.
Completed successfully.
But the problem is again same. It shows optimizing android and screen goes blank after 3 of 32 app or 4 of 32 app.
Have I messed up the recovery ?
I am able to go into download mode and LG up reads it as H81520p.
Plz guide
Foto-AG said:
For my undstanding....
1) You have still H81520p_00_0314.kdz running on your Phone ? but no Indian Band ?
2) What Header is LGUP showing now?
If you have H81520p_00_0314.kdz on it, you are able to Downgrade to ever Version you want, H81520p_00_0314.kdz make it possible only !
So, find out your Rom for your Location and flash it with LGUP. Keep the 8994 dll it comes from H81520p_00_0314.kdz in the folder and flash.
After downgrade with LGUP (Refurbish Mod ) do a Over the Air update on your Phone or via LG Bridge and do "correct update Error" instead of "Search for Updates" and normaly its works.
Follow this Links for the Roms
http://storagecow.eu/index.php?dir=Xda/
https://lg-kdz-firmware.com/
If you are unsure what rom you must get, go to https://lg-firmware-rom.com/
and type your IMEI in and watch for the results.
Greetings....
Click to expand...
Click to collapse
Plz read above happenings.
What do you think ?
Plz guide
Thanks
frend2001 said:
Well
Problems just dont seem to end.
I hooked it up with LG bridge.
It showed model as "G4".
No version no code just G4.
I started to update it (thats before I read your msg)
Update stopped in between and phone turned off. I unplugged it and pulled out the battery. Restarted.
It showed LG logo and agained turned off.
I tried to reset by pressing Down vol n power button.
Options came to reset n I reset it.
Now again turned on. It showed optimizing android.
Stopped at 4 of 32 app and screen went blank.
Now LG bridge reads it as L500F at place of G4.
Hooked up again in download mode and LG UP disnt recognize it. Again restarted.
LG up recognized as H81520p.
I reflashed thr H815 20 p kdz.
Completed successfully.
But the problem is again same. It shows optimizing android and screen goes blank after 3 of 32 app or 4 of 32 app.
Have I messed up the recovery ?
I am able to go into download mode and LG up reads it as H81520p.
Plz guide
Click to expand...
Click to collapse
I will do my Best my Friend.
I don't understand why the optimizing Process stops....
Maybe there is something blocking the process.
My only idea now is to flash Twrp on it and wipe all chaches. Davlik,Data and Cache and let the phone boot up and see what is going on. This is the working TWRP for G4 on H81520p
https://drive.google.com/file/d/1sOsVDs1vZzuvirWQ0ByFPZv9BC9Eu4yH/view?usp=sharing
But for twrp flashing the Bootloader must be unlocked. You can do this on lg developer page ( https://developer.lge.com/resource/mobile/RetrieveBootloader.dev ), type in your IMEI and you get a unlock.bin via email.
I think you know the process for Bootloader unlocking otherwise i will guide you.
Greetings from Germany
Foto-AG said:
I will do my Best my Friend.
I don't understand why the optimizing Process stops....
Maybe there is something blocking the process.
My only idea now is to flash Twrp on it and wipe all chaches. Davlik,Data and Cache and let the phone boot up and see what is going on.
But for twrp flashing the Bootloader must be unlocked. You can do this on lg developer page, type in your IMEI and you get a unlock.bin via email.
I think you know the process for Bootloader unlocking otherwise i will guide you.
Greetings from Germany
Click to expand...
Click to collapse
Hi
Can bootloader be unlocked in LG G4 MM ?
Initially when i flashed nougat TOT on it, the firmaware update page was either in korean or chinese then after nougat TOT flash ot became in english.
Could it be that the recovery is also overwritten ?
Plz point me to bootloader unlock for it.
Many thanks from India
frend2001 said:
Hi
Can bootloader be unlocked in LG G4 MM ?
Initially when i flashed nougat TOT on it, the firmaware update page was either in korean or chinese then after nougat TOT flash ot became in english.
Could it be that the recovery is also overwritten ?
Plz point me to bootloader unlock for it.
Many thanks from India
Click to expand...
Click to collapse
Hey.
Yes you can unlock Bootloader in MM too.
After the bootloader is unlocked, the Phone will reboot and do a Hardreset itself, you can´t do anything to block the Hardreset.
Notice: After flashing in any Versions the Recovery will be deleted too !! Example, if you have TWRP on the Phone and flashing any kind of firmware, the Recovery with TWRP in it will be deleting..thats normal in the flashing process.
BUT you CAN´T unlock the Bootloader yet ! You must enable the Developer Mod in the Phone first and set OEM unlock.
Your Phone does not boot up correctly at this moment, this Problem MUST be solved first !!
Did you try a Hardreset ?
Switch Phone off, pull Battery and place it back. Press the Volume down Button and keep hold and press Power Button and keep pressed, after LG Logo is showing up, release the Power Button for 1 secound but still keep Volume down pressed. Press Powerbutton again and hold pressed until the Green Android thing is showing up, release both buttons now.
In short: After Battery was pulled and replaced..
Press and hold VOL -
Press and hold Power
after LG Logo is showing up
Release Power 1 Sec. and press again and hold until Android puppy is showing, release both Buttons.
Now the Phone should boot up and do the optimazion process correctly.
If not, then i have no more ideas. Maybe flash a MM 5.0 Version over the MM 6.0 via REFURBISH option in LGUP
Hopefully something works for you.
Foto-AG said:
Hey.
Yes you can unlock Bootloader in MM too.
After the bootloader is unlocked, the Phone will reboot and do a Hardreset itself, you can´t do anything to block the Hardreset.
Notice: After flashing in any Versions the Recovery will be deleted too !! Example, if you have TWRP on the Phone and flashing any kind of firmware, the Recovery with TWRP in it will be deleting..thats normal in the flashing process.
BUT you CAN´T unlock the Bootloader yet ! You must enable the Developer Mod in the Phone first and set OEM unlock.
Your Phone does not boot up correctly at this moment, this Problem MUST be solved first !!
Did you try a Hardreset ?
Switch Phone off, pull Battery and place it back. Press the Volume down Button and keep hold and press Power Button and keep pressed, after LG Logo is showing up, release the Power Button for 1 secound but still keep Volume down pressed. Press Powerbutton again and hold pressed until the Green Android thing is showing up, release both buttons now.
In short: After Battery was pulled and replaced..
Press and hold VOL -
Press and hold Power
after LG Logo is showing up
Release Power 1 Sec. and press again and hold until Android puppy is showing, release both Buttons.
Now the Phone should boot up and do the optimazion process correctly.
If not, then i have no more ideas. Maybe flash a MM 5.0 Version over the MM 6.0 via REFURBISH option in LGUP
Hopefully something works for you.
Click to expand...
Click to collapse
SO Finally it's dead.
I tried to hard reset and the puppy appeared and then it rebooted. Again went to optimizing apps. Stuck at 14 of 32.
Became unresponsive.
I pulled out the battery and reinserting after 20 sec.
Nothing.
After several battery removal and reinserts, I managed to get it in download mode.
I was trying to Flash H815 20p KDZ again as it was working initially. But at 50% process of flashing, it shows error of USB Disconnected and phone screen went blank.
Since then it was neither starting nor getting in download mode. Tried everything.
It doesn't even show after connecting to PC.
Dead as dodo.
I looked at it with more attention. Removed the battery cover saw the model on mobile body,
it has model no H811
On box the model no is H815
LG Bridge recognized it as F500L.
IMEI No search says its F500L.
So basically it looks to either a refurbished phone or a fake.
I bought it thru eBay on 18th Jan 18. So I had to claim refund against a faulty product.
I suppose I'll get a refund, I will skip replacement as it's likely that the seller might again push a refurbished / fake phone.
End of the story till then.
If I dont get a refund I'll revive the thread.
Thanks to FOTO AG and XDA for support n advice.
frend2001 said:
SO Finally it's dead.
I tried to hard reset and the puppy appeared and then it rebooted. Again went to optimizing apps. Stuck at 14 of 32.
Became unresponsive.
I pulled out the battery and reinserting after 20 sec.
Nothing.
After several battery removal and reinserts, I managed to get it in download mode.
I was trying to Flash H815 20p KDZ again as it was working initially. But at 50% process of flashing, it shows error of USB Disconnected and phone screen went blank.
Since then it was neither starting nor getting in download mode. Tried everything.
It doesn't even show after connecting to PC.
Dead as dodo.
I looked at it with more attention. Removed the battery cover saw the model on mobile body,
it has model no H811
On box the model no is H815
LG Bridge recognized it as F500L.
IMEI No search says its F500L.
So basically it looks to either a refurbished phone or a fake.
I bought it thru eBay on 18th Jan 18. So I had to claim refund against a faulty product.
I suppose I'll get a refund, I will skip replacement as it's likely that the seller might again push a refurbished / fake phone.
End of the story till then.
If I dont get a refund I'll revive the thread.
Thanks to FOTO AG and XDA for support n advice.
Click to expand...
Click to collapse
Sorry to hear that Mate.
Hopefully you get a christall clear G4 one Day. Maybe you get an other Model in the Future, a Samung or similar,who knows.
Wish you all the Best !
maybe a hint for you, pls watch this
https://www.youtube.com/watch?v=dj5TDjvqv54
Greets
You should have hexedited a F500L tot(wich is your motherboard version) and changed the LGX to H815, saved the file and then flashed. That could been solved your issue and turned your phone back to F500 with a functional and booting system