Develop Bugs

Mobile Wi-Fi router stopped working

So I've been using the Tom coding package that installs the mobile Wi-Fi router with no problems until last night... now it keeps trying to connect to ISP.Cingular and then stops... it basically doesn't work now. I've tried to uninstall and reinstalled it dozens of times with no luck.
And yet... the 3G connection works because I can browse through Opera. So...?

OhI might add that I can turn on the Wi-Fi and connect to my in-house router just fine and do what on the internet through the phone. SO... it is definitely something specific with wireless internet sharing.
???
Someone please he me I use internet sharing DAILY

You need to make sure that it is connecting to the correct address. At the bottom of the App, it should have a few different choices of connections to use. Try another one and see if it works. You may have to set up a new connections for this to work properly. Keep in mind that tethering/mobile hotspot is not covered by AT&T's wireless data plan. It is a separate monthly charge. You should be careful when using it too much at a time, so they don't block or throttle your connection.

The device I am trying to connect with to my Tilt 2 is a Samsung Galaxy Tab, and apparently it doesn't like ad-hoc, whatever that is exactly. I was told on the Galaxy Tab section of this forum that this is the case, and that I need some kind of "mobile ap", although again I do not understand what that exactly means. ???

Ah, see that's much better information. So, no, you probably won't be able to connect without another app doing so. Ad-hoc is, simply put, a connection to another device other than a router which is allowing you access to its Internet connection. If the device you're trying to connect with doesn't allow ad-hoc connections, then the Wifi Router app won't do you any good, as that is the type of connection it uses. Most mobile devices do not natively support this, however. The problem, therefore, is with the Galaxy Tab you have, not with the TP2. Find an app or mod that allows for ad-hoc connections and you'll be all set.

Well is there an apparently for the WM phone side of things that will do non ad-hoc??

No. Ad-hoc is a connection between two devices. Unless you use a router, that's how it's going to be no matter if you are using WM, a laptop, iOS, Android, et cetera. The connection type is determined by the device sending the signal. If it comes from a device, then it is ad-hoc. It is not a problem with the software. That is how wifi was designed to work in the first place. The problem, again, is with the Tab, not the WM application.

Well apparently there is a solution for the Tab that allows it to see ad-hoc networks, so I will try that and let you guys know how it went.

Can no longer connect to Ad-Hoc with Tilt 2
I have been using both the CM Internet Sharing program and the WMWifiRouter with no issues for over a year now on my AT&T Tilt 2.
One day a couple weeks ago I had been using CM to connect my laptop to the internet. everything was just fine as usual.
At some point, I had disconnected and tried to reconnect, and since then I can no longer use either of these programs.
What happens is this...I turn them on and the phone will no longer hold a connection to the ad-hoc network that is created. Up in the status bar I see the icon showing WiFi trying to connect but it will not stick anymore.
I can connect to my office and/or home wifi router still. It just will not connect to the ad-hoc network any longer.
This makes no sense to me at all, since it has always worked and was even working earlier in the day when it stopped working.
I use the tethering frequently and really need to get this solved. Any help would be greatly appreciated.

Bt Home Hub 2 Problems

Hey
I've got some severe wifi problems with the BT infinity Home Hub 2.0:
1. Sometimes I cannot connect to the hub and the phone cannot get passed "obtaining ip address"
2. On rare occasions I can connect to the hub but no data is transferred and to make matters worse it takes down the wifi network for others (Other devices remain connected but no data is transferred) To get things working again I have to reset the hub!
If I try connecting to BT Fon or BT Openzone on my network the same problems occur. (Other BT broadband users will understand what I'm talking about there)
What I've tried to fix the issues:
I've tried setting a manual ip address with no luck
I've tried a full reset of the hub
Changed the wifi channel of the hub
Turned on best performance in wifi settings on the One X
I've tried a variety of roms and am currently on Viper
I experience these issues when connecting to other BT Home Hubs and other random hotspots. But at the same time I have no issues issues connecting to other wifi hotspots such as hotel ones and public hotspots.
At the moment at home I've got an old voyager 2100 bridged to the hub and I can connect through that with no problems, but as you can understand I don't really want two routers running at the same time when it shouldn't be necessary.
If anybody has any suggestions it would be greatly appreciated!
Thanks :cyclops:

Working perfect on my HH2. I say perfect, but as well as the HH2 will work, you'll get what I mean.

blackalice said:
Working perfect on my HH2. I say perfect, but as well as the HH2 will work, you'll get what I mean.
Click to expand...
Click to collapse
Looks like my phone is in need of repairing..

chattyuk said:
Looks like my phone is in need of repairing..
Click to expand...
Click to collapse
Just noticed you have the infinity version, which I assume is totally different.
Sorry about that!
(however, I'm stuck on sub 8mb (2mb, ish) in the country, I'd put up with dodgy wifi for your connection )

blackalice said:
Just noticed you have the infinity version, which I assume is totally different.
Sorry about that!
(however, I'm stuck on sub 8mb (2mb, ish) in the country, I'd put up with dodgy wifi for your connection )
Click to expand...
Click to collapse
It's pretty much identical but I've had the same issues on other normal home hub 2s

I had the same problem whereby every time my One X connected to my Home Hub, it would cause the network to become unresponsive for all connected devices! I eventually found that changing my hub settings from 802.11 b/g/n to just 802.11 b/g did the trick.
Go here: 192.168.1.254
then: Settings --> Advanced Settings --> Wireless --> Wireless interface type.

apwb said:
I had the same problem whereby every time my One X connected to my Home Hub, it would cause the network to become unresponsive for all connected devices! I eventually found that changing my hub settings from 802.11 b/g/n to just 802.11 b/g did the trick.
Go here: 192.168.1.254
then: Settings --> Advanced Settings --> Wireless --> Wireless interface type.
Click to expand...
Click to collapse
Thanks! I'll give this a go when I get home, I wonder what the underlining issue is here that's causing all of these problems

i don't think its the phone, id blame the router, mine does similar sometimes, works after a reboot of the router though

Hi,
I encountered this issue just recently. I have a Galaxy S3 and a HomeHub2 with Infinity. I tried setting a manual IP address, rebooting router and phone, changing wifi channel etc, but none of that worked. I later noticed that the dhcp table on the router was full of expired leases for the same device. I clicked the "refresh" button on the HH2's dhcp page and it refreshed showing a list of different mac address - weird - but this time showng them with an "andriod" prefix. I manually deleted a few of the expired entries - one at a time (pita) and that seemed to fix it, i.e. I was able to reconnect and get an IP address assigned on my S3 again. I've since selected the option to "always use this ip address" on the dhcp table entry details page (just click one of the items in the list to view). I guess there must be a bug/conflict/glitch between andriod and the hh2's dhcp service which perhaps prevents expired ip address assignments from being dropped and reused. I have a few other devices that are wireless and use dhcp (ps3, iphones, ipad, ipod touch, wii, samsung smart tv, wifi printer, microwave, fridge... ok i'm kidding about those last two , and none of those have multiple expired sessions.
Hope this helps someone get round the problem.
Jeremy
PS: Great noob vid.

Funny this is here. I had this exact issue its frikking irritating. I went through the hassle of unlocking the hub to work on talk talk...I had my nexus then and it flew..I know the nexus is like that though lol. So got the x was a nightmare on WiFi.coverage wise also in the kitchen..it went below a bar. So changed to b and g only. Works okay but still is slow ans doesn't do well. Annoying seeing the hub is capable of n
Sent from my HTC One X using xda app-developers app

chattyuk said:
Hey
I've got some severe wifi problems with the BT infinity Home Hub 2.0:
1. Sometimes I cannot connect to the hub and the phone cannot get passed "obtaining ip address"
2. On rare occasions I can connect to the hub but no data is transferred and to make matters worse it takes down the wifi network for others (Other devices remain connected but no data is transferred) To get things working again I have to reset the hub!
If I try connecting to BT Fon or BT Openzone on my network the same problems occur. (Other BT broadband users will understand what I'm talking about there)
What I've tried to fix the issues:
I've tried setting a manual ip address with no luck
I've tried a full reset of the hub
Changed the wifi channel of the hub
Turned on best performance in wifi settings on the One X
I've tried a variety of roms and am currently on Viper
I experience these issues when connecting to other BT Home Hubs and other random hotspots. But at the same time I have no issues issues connecting to other wifi hotspots such as hotel ones and public hotspots.
At the moment at home I've got an old voyager 2100 bridged to the hub and I can connect through that with no problems, but as you can understand I don't really want two routers running at the same time when it shouldn't be necessary.
If anybody has any suggestions it would be greatly appreciated!
Thanks :cyclops:
Click to expand...
Click to collapse
Turn off 802.11n - That is the problem with the Home Hub 2.0. It's buggy as f00k.
Sent from my HTC One X using xda premium

Yeah after I wrote this plugged my old Thomson in..all sweet again now just need a new n router again
Sent from my HTC One X using xda app-developers app

I'm having the exact same problem but with the homehub 3, I was convinced it was a faulty router and have been pestering bt for a new one. I realized it was the phone whenever the same problem happened at the father in laws house (he has a hh3 also). I have been using cyanogenmod for a a few months and this prob only occoured when I started using mike1986's Rom... Maybe someone should tell him

I'm having issues with my One X and my HH3 , it's only started since i went to jellybean. It was fine before now when my HOX is conneced to the router all wireless devices (Ipad and laptops-win7/ubuntu) will drop out and back in of connection. Sometimes the router will drop it's broadband connection then come straight back up.
It's driving me mad.

[Q] More Wifi questions...

I have a N7100 and I am also having wifi connectivity issues
I read the old wifi connectivity thread but my issue doesn't seem to be the same.
.I have a broadband wifi router which I also use an iPad, win Xp laptop, HTC Wildfire S and Motorola defy through, all of which have been fine (using WEP encryption)
)Unfortunately the note II seems to connect but then doesn't access the Internet.
The phone's wifi page shows connection. It connects then receives and IP address but then the alert comes up that there is no Internet access. I also use fing which says that there is no wifi network.
I''ve downloaded the apps wifi manager and wifi analyser to try and get to the bottom of it but they both say I have good signal strength and are connected.
Wifi analyser showed there was a bit of crossover from another AP router next door so I changed the channel to give clear air between us. I then reconnected all the devices and they all work -apart from my new Note.
My question so are 1)is there any more i can do to fix it. 2)where should I look to find the logs which might let me diagnose it a bit better . I should add that sometimes it just works and can browse and download as normal, but most of the time it doesn't.

I started to have trouble connecting to wifis few days ago, it says that signal is very strong i even see full bars and it stops on "containing IP adress" and then shows up window that signal is poor and doesnt connect, but wifi is working my friend next to me was connected, its in a bar and like 2 weeks ago i was able to connect to that very same wifi, very disappointing, no clue what could be wrong

P600 wifi connectivity

I'm having an issue where my WiFi connection drops. Tab still says connected but I get no throughput. All other wireless devices still work. I have to toggle the wifi on the tab on and off to reconnect. Router is an actiontec C1000A.
I've read other threads where people had similar issues and exchanged tablets for new ones only to have them do the same. Router is good, it works with all my other devices without issue. What good is a WiFi only tablet if the WiFi sucks eggs?

squabeggz said:
I'm having an issue where my WiFi connection drops. Tab still says connected but I get no throughput. All other wireless devices still work. I have to toggle the wifi on the tab on and off to reconnect. Router is an actiontec C1000A.
I've read other threads where people had similar issues and exchanged tablets for new ones only to have them do the same. Router is good, it works with all my other devices without issue. What good is a WiFi only tablet if the WiFi sucks eggs?
Click to expand...
Click to collapse
Well my wifi has been brilliant, the only issue I had was that although my wifi router was working with every other device and even my Note 10.1 it didnt want to play youtube videos on it. So I changed connection to my other broadband and it worked a treat so even though your router works with other devices it doesn't mean the tablet is faulty just that the router and tablet don't like each other.
Best way to try this is go to a friends house and try their connection or go to a coffee shop where they have free wifi and hopefully you will see wifi doesn't suck eggs lol. Anyways hope your problem gets sorted.

squabeggz said:
I'm having an issue where my WiFi connection drops. Tab still says connected but I get no throughput. All other wireless devices still work. I have to toggle the wifi on the tab on and off to reconnect. Router is an actiontec C1000A.
I've read other threads where people had similar issues and exchanged tablets for new ones only to have them do the same. Router is good, it works with all my other devices without issue. What good is a WiFi only tablet if the WiFi sucks eggs?
Click to expand...
Click to collapse
Are you just complaining or are you asking for help?............ If your asking for help please tell us if you are using 2.5 or 5ghz, b, g, n, ac, channel #. Many things can cause wifi issues and sometime a monitoring app from the play store like "Wifi analyzer" can help narrow down whats really going on.

Im asking for help by complaining. I'll get some more detailed info on my network and post it up later.

My modem/router was set to auto detect... I used wifi analyzer to set it to a less crowded fixed channel. I also turned off 802.11n. It had b, g and n simultaneously... Now it's just b and g. So that's 2.4 GHz? I don't have super Internet, so no real need for "n". I'll report back after I see if this changes anything. The security is WPA2-Personal...don't know if that has any effect. Any other ideas are appreciated.

Unable to detect wifi network...!!!

I am using D-Link 2750U ADSL router, the issue I am facing is quite weird. My Phone, Laptop, Nexus 7 Tab can see Wi-Fi Network in range but Samsung Galaxy Tab 3 (10.1) cannot see Wi-Fi network. I tried connecting it manually by providing SSID, it says Network not in range. Interestingly, Samsung tab connects to Wi-Fi network in my office without any issues. So I am clueless as to where the problem is – is it with Router or Tab? Can someone help please

heeemz said:
I am using D-Link 2750U ADSL router, the issue I am facing is quite weird. My Phone, Laptop, Nexus 7 Tab can see Wi-Fi Network in range but Samsung Galaxy Tab 3 (10.1) cannot see Wi-Fi network. I tried connecting it manually by providing SSID, it says Network not in range. Interestingly, Samsung tab connects to Wi-Fi network in my office without any issues. So I am clueless as to where the problem is – is it with Router or Tab? Can someone help please
Click to expand...
Click to collapse
crash your router, try again
access your router, check your settings,history
try unsecuring your wifi, seemif it picks up, then resecure
tab does 80211 abgn, check you're setmfor wpa2-passkey
in your tab if always scan is enabled, toggle it
check system/etc/wifi/nvram* - if present
it's most likely the router and the tab.

Issue resolved (hopefully) by setting channel to fixed number rather than using auto option in router wifi settings.
Interesting aspect is my phone, which is also samsung (s4) and laptop had no issues.

@heeemz
channel!, Uhhh, weird,
My best guess is that you have a router with Full open channels like for Europe or Japan and that the TAB3 is an American version. So as American Wifi is not allowed to transmit on EU/Japan extended frequencies?

r2d23cpo said:
@heeemz
channel!, Uhhh, weird,
My best guess is that you have a router with Full open channels like for Europe or Japan and that the TAB3 is an American version. So as American Wifi is not allowed to transmit on EU/Japan extended frequencies?
Click to expand...
Click to collapse
This looks like best possibility...
Sent from my GT-P5210 using XDA Free mobile app

I have ATT 7 inch and it has similar issues on my home wifi... also a dlink router... I have 3 cellphones, wifi tv and 2 other tablets on the wifi and no issues.
I will check my channels.