Has anyone tried one of these qi receiver tags that plugs into your Micro USB port?
http://www.ebay.com/itm/Universal-Q...S_Cell_Phone_PDA_Chargers&hash=item27e5adb896
http://www.ebay.com/itm/Universal-Q...l_Phone_PDA_Chargers&var=&hash=item2c83141608
I know they aren't optimal, but I figured if it works it would be a good hold over until good ones come out for the G3 specific.
I will let you know when my phone gets in, I have one left over from my LG G2. I don't see why it shouldn't work though.
Charsher47 said:
I will let you know when my phone gets in, I have one left over from my LG G2. I don't see why it shouldn't work though.
Click to expand...
Click to collapse
Thanks. Any idea which one I should look at getting? Haven't seen a good enough shot of the micro USB port to make sure I get one facing the right direction. I've got Amazon Prime so I'll probably get one from there to test.
http://www.amazon.com/Universal-Wireless-Charging-Receiver-micro-USB/dp/B00H7FJX7M/
That one is on Amazon, Prime, and has 2 different models. Anyone seen a close enough photo to know which one we'd need? Port A or Port B?
I'm going to try to find one with a metal plug instead of this plastic one.
This one has tons of different options. Less than $11 on prime.
http://www.amazon.com/Universal-Wireless-Charging-micro-USB-narrow-interface/dp/B00I1D4DWO/
Sorry for the multiple posts, I thought it would collapse them.
From what I saw in pictures, it should be this one correct?
Universal QI Wireless Charging Receiver film for micro-USB of All Android Mobile (middle/narrow-interface Up)
Click to expand...
Click to collapse
If so I'll pick one up today so its here for testing when my phone arrives.
Yes I got one and didn't work.
Didn't charge at all? Can you give us some specifics?
No didn't even register on the phone. It was only $7. I ended up ripping out the Quick Circle charging coil and putting it in my phone. Works a treat!
Thanks. Do you know exactly which one you used (perhaps a link to where you purchased) so those of us that want to test other ones skip it?
RED ZMAN said:
Thanks. Do you know exactly which one you used (perhaps a link to where you purchased) so those of us that want to test other ones skip it?
Click to expand...
Click to collapse
Yes sorry can't remember where I bought it from. I think eBay? This is it...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Im using this one; http://www.amazon.com/gp/product/B00HI8JYFE/ref=oh_details_o00_s00_i00?ie=UTF8&psc=1
No problems after all. Working OK with my F400K
So now its working? Awesome! Buying 2 right now.
Mine works as well, I have this one: http://www.amazon.com/gp/product/B00IQ2GUFI/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
BUT it only works if i have the receiver stuck on the back of the phone in between it and the phone case. If I have it on top of the battery the signal doesn't make it through.. perhaps because of the curved nature of the phone and the NFC receiver on the inside of the back cover.
I was always under the impression that NFC and wireless charging interfered with each other unless it was one integrated unit. That's probably why yours only works that way.
Well I got mine and tried it out, and while it does work, kind of, I'm sending them back. The cable ribbon is so thin it feels like it is going to rip, it would also need you to bend it at a bad angle to get it inside a case or inside the back. I can't get a GOOD charging connection with my TYLT VU chargers, so it is going back.
RED ZMAN said:
Well I got mine and tried it out, and while it does work, kind of, I'm sending them back. The cable ribbon is so thin it feels like it is going to rip, it would also need you to bend it at a bad angle to get it inside a case or inside the back. I can't get a GOOD charging connection with my TYLT VU chargers, so it is going back.
Click to expand...
Click to collapse
The cable ribbon is probably thin because you need to bend it at weird/sharp angles and it has to fit in the cracks of the back or case. As long as you're not constantly pulling on it, there's really no risk of tearing. Connections are fine with my $20 chargers, I can drop it on pretty much anywhere in the vicinity of the receiver and it'll charge.
Charge rate depends on which receiver you go with. Most, including the ones posted here, are 500mA which is kind of slow. I should be getting an 800mA one soon so hopefully that'll pick up the pace. IMO, these are still better than switching to PMA.
Its not so much the thin that bothers me, it is how flimsy it is. I mean it could have some reinforcement of some kind you'd think. And it leaves the pad really low on the phone, probably part of the reason it doesn't connect well even with a QI pad a good as the TYLT VU. Just removing the thing to root my device was scary, I thought the USB plug was going to tear off and stay in.
I just bought 2 battery covers with integrated Qi/NFC for $23 each on ebay (my wife got a G3 also) so that should fix the issues for me. Not sure what the VU charges at, but with my Nexus 5 it was always great, for a heavy user like me, I was satisfied (Qi dock in my car too).
What kind of qi car dock do you have? I love the wireless charging and have seen a few posts you put on XDA. I ordered that back plate from eBay, hopefully it works OK and I had ordered the sticker from China but it seems like a pain in the ass ripping off the old one.
Sent from my VS985 4G using XDA Free mobile app
Let me find a link for you. Been really happy with it. Glad my posts are helping folks!
RED ZMAN said:
Its not so much the thin that bothers me, it is how flimsy it is. I mean it could have some reinforcement of some kind you'd think. And it leaves the pad really low on the phone, probably part of the reason it doesn't connect well even with a QI pad a good as the TYLT VU. Just removing the thing to root my device was scary, I thought the USB plug was going to tear off and stay in.
I just bought 2 battery covers with integrated Qi/NFC for $23 each on ebay (my wife got a G3 also) so that should fix the issues for me. Not sure what the VU charges at, but with my Nexus 5 it was always great, for a heavy user like me, I was satisfied (Qi dock in my car too).
Click to expand...
Click to collapse
Do you have a link to the ones you bought? Also could you post some pictures when you receive and install them?
Related
Looks pretty good and has room to charge another battery while your phone is docked and charging.
http://cgi.ebay.com/USB-Battery-Dock-Charger-Cradle-HTC-Thunderbolt-4G-/300540578121?pt=PDA_Accessories&hash=item45f99d4949#ht_2490wt_952
Hm.. nice find. That is tempting. I wish it was a bit cheaper.
I'll probably pick one up anyways to use at work. Looks like it won't fit a tbolt with a case.
eleazar123 said:
Hm.. nice find. That is tempting. I wish it was a bit cheaper.
I'll probably pick one up anyways to use at work. Looks like it won't fit a tbolt with a case.
Click to expand...
Click to collapse
Yeah looks like the TB will have to be naked to fit in this dock. Please post your review as soon as you get it.
If you wait a bit, I'm certain you'll be able to find it cheaper on ebay. You should start seeing other chineese companies selling them for much less, but shipped from China (slower to get here though).
I have the Incredible dock that is similar, and hacked it up to hold the phone with a case on it (doesn't look pretty, but it DOES work).
yep i bought one from amazon...listed that its for the merge but it fits....its tight but it fits...also it has to be naked..which sucks, but the for the price its a good deal
http://www.amazon.com/gp/product/B004JX1FOY
92slammer said:
yep i bought one from amazon...listed that its for the merge but it fits....its tight but it fits...also it has to be naked..which sucks, but the for the price its a good deal
http://www.amazon.com/gp/product/B004JX1FOY
Click to expand...
Click to collapse
When you plug the TB in, does sense rotate to landscape like the car dock?
Sent from my Thunderbolt using Tapatalk
gadget! said:
When you plug the TB in, does sense rotate to landscape like the car dock?
Sent from my Thunderbolt using Tapatalk
Click to expand...
Click to collapse
Virus rom does rotates without the dock.
gadget! said:
When you plug the TB in, does sense rotate to landscape like the car dock?
Sent from my Thunderbolt using Tapatalk
Click to expand...
Click to collapse
no it doesnt .....and scratch this off your list....it stopped working this morning....the usb charger part for the phone died....returning to amazon now!
was it the adapter that died or the connected cord or plug set in the dock? would love to buy this, especially for the price.
jacobk said:
was it the adapter that died or the connected cord or plug set in the dock? would love to buy this, especially for the price.
Click to expand...
Click to collapse
not sure....it just stopped charging the phone...would charge the spare battery fine though
Thanks for the Amazon link, been looking for a dock with spare battery charger for cheap.
i was going to buy this but not now since it stopped working for you
92slammer said:
not sure....it just stopped charging the phone...would charge the spare battery fine though
Click to expand...
Click to collapse
I had that problem on my charger for the DInc, and it ended up the actual USB plug housing had split apart, and the plug was sliding back into the housing. I ended up fixing it (mine came from china, so no recourse there), and it still works fine. Just curious if that was the problem with your unit or not.
Also looks like you can get it cheaper on ebay now. As with anything from China, you take a gamble on quality... I might pick one up and see if it works with my pop case, although the USB header might be a tad too short to reach and some plastic will definitely have to be shaved off to get it to fit the back.
Anyone find a charger without the big extra battery back?
heffe2001 said:
Also looks like you can get it cheaper on ebay now.
Click to expand...
Click to collapse
I just ordered it...I will give an update when I receive it.
loztboy said:
Yeah looks like the TB will have to be naked to fit in this dock. Please post your review as soon as you get it.
Click to expand...
Click to collapse
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Yes, it has to be naked in order to fit into the dock.
I have 23 of these in stock... tested one and it works great.
Any questions let me know.
I ordered one too - figured not too big of a risk for that $$ and my TB will be staying naked anyway. $25 shipped on Ebay vs $60(!) for the official one.
Edit:
Funny, as soon as I posted this, the dock arrived - FAST shipping! The dock is not bad, works fine. The only complaint I have is that the phone is held almost completely vertical, no angle at all really. So that makes it a little awkward for watching video but not too bad. Charges fine, USB works fine, insertion and removal is easy. As stated before, you cannot use a case with this dock, it is a snug fit. Slot on the back for charging a second battery.
Time will tell with the durability, but it serves my needs well - easy place to plug in and charge at my office desk. Recommended especially considering the price. If the HTC dock has HDMI (I doubt it) then maybe it will be worth $60. In the meantime this is shipping and shipping fast!
I'd buy one of these if the extended battery would fit on the dock :/
boingboingbilly said:
The only complaint I have is that the phone is held almost completely vertical, no angle at all really. So that makes it a little awkward for watching video but not too bad.
Click to expand...
Click to collapse
I ordered one as well, and your complaint is the same as mine...
The phone is almost vertical when docked.
I will not be using it.
In fact if anyone wants it, I'd sell it for 20 bucks shipped (US only).
FWIW Newegg has them for $28, but they are out of stock right now....
Dock
Just found these desktop docks at Mobile Fun:
Standard
http://www.mobilefun.com/35463-samsung-galaxy-s3-case-compatible-charging-dock.htm
Dual Charge
http://www.mobilefun.com/35464-samsung-galaxy-s3-case-compatible-dual-charging-dock.htm
Anyone use one of these? They look like they would hold the phone more securely than the Samsung dock, and they're fairly cheap as well.
One thing I'm curious about - With my old Nexus One, I used to be able to set the phone in the dock, and it would automatically switch into home mode. This mode would display the clock and weather, and then switch to a dim alarm clock at night. Anyone know if the S3 behaves the same way, or if any of the after market docks support this feature?
Update: I bought the standard version of this, in black. Here's some thoughts...
It takes a few weeks to receive one of these, since they are shipped from overseas, even if you order it from the .us version of their site.
The Galaxy S3 does not recognize this as a dock, so the phone doesn't automatically switch to desktop dock mode. This XDA thread has info on DIY hacking to address this. It's also been suggested NFC might be a good workaround for this.
The dock is fairly solid, and holds the phone securely. It's very light, but the footprint makes it pretty stable and unlikely to tip over if bumped.
It has a small pop out piece that allows docking the phone even when using a slim fitting case. I have the Rock Quicksand case, and it's a little bit loose, so something slightly thicker than that should still fit.
This is a good looking dock with a glossy black face and flat black sides, but unlike the pictures on the website, there's a white KiDiGi logo on the front of it. This logo is screenprinted on, and I'm not sure if there is any way to remove this without damaging the finish.
It has a standard micro usb connecter on the back of the dock, so any of your typical charging or syncing options should work. It also ships with a standard usb to micro usb cable, instead of the UK mains to micro usb cable as originally stated on their website. Perhaps they've changed this for the US market.
Overall, this is a pretty nice dock for the price.
It looks like it can be docked while the S3 is in a case. I wonder how thick the case can be?
I was usedto the one from captivate so I ordered 2 of these
http://cgi.ebay.ca/ws/eBayISAPI.dll?ViewItem&item=310404943509
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I just ordered the kidigi dual dock - I'll let you know what I think once it gets here from HK.
Apparently the maker (kidigi) has a white version.. I can't find it onsale anywhere yet.
Diznario said:
Just found these desktop docks at Mobile Fun:
Standard
http://www.mobilefun.com/35463-samsung-galaxy-s3-case-compatible-charging-dock.htm
Dual Charge
http://www.mobilefun.com/35464-samsung-galaxy-s3-case-compatible-dual-charging-dock.htm
Anyone use one of these? They look like they would hold the phone more securely than the Samsung dock, and they're fairly cheap as well.
One thing I'm curious about - With my old Nexus One, I used to be able to set the phone in the dock, and it would automatically switch into home mode. This mode would display the clock and weather, and then switch to a dim alarm clock at night. Anyone know if the S3 behaves the same way, or if any of the after market docks support this feature?
Click to expand...
Click to collapse
I really like how there's no logo on the front. I don't mind saving a few bucks by getting a non-Samsung brand, but I don't like seeing the name of some obscure brand plastered across the front of the dock (like this one)
As for the part about the home mode... I suspect you could maybe accomplish this with an NFC tag. There appears to be enough flat real estate on the dock to fit a square on there. I don't know how well it would line up with the receiving part of the phone, which I imagine is more towards the center? Definitely some testing would need to be done before sticking it on.
EDIT: I just noticed in the item description it says it comes with a "UK AC Power Adaptor." Spelling mistake aside, I'm a bit bummed by that.
Excellent point on the NFC tag. That dock in particular does seem to have the perfect spot for it.
I bet that UK power adapter goes to micro USB, which then plugs into the back of the dock. That's how my last dock was. If that's the case, then you should be able to use any other micro USB power you have handy. but yeah, that is sort of a bummer.
There is another dock like this for sale on ebay too. The ebay one has an LED on the front of it though:
http://www.ebay.com/itm/USB-Sync-2n...713864?pt=PDA_Accessories&hash=item2c6668ee88
cweemin said:
Apparently the maker (kidigi) has a white version.. I can't find it onsale anywhere yet.
Click to expand...
Click to collapse
Totally gunna wait for this version to come out. Was gunna pre order a mugen one but white would look so sweet with the white phone. Extra battery slot and charges phone.
Sent from my SPH-L710 using xda premium
I just ordered one of these:
http://www.amazon.com/gp/product/B008AFSSRE/ref=oh_details_o01_s00_i00
should be here in a few days
z0phi3l said:
I just ordered one of these:
http://www.amazon.com/gp/product/B008AFSSRE/ref=oh_details_o01_s00_i00
should be here in a few days
Click to expand...
Click to collapse
ME TOO!
I figured for $12 it was worth a try...and from a review I saw of one that looked identical but had a branding on it I felt it was a good option.
Plus from what I have read/watched it appears it may be a little nicer to play with a TPU case where I am not sure the Kidigi will work with most TPU Cases...though slim cases like the Rok case and others that more cover the back and sides but don't have the face lip appear they will work fine with the Kidigi with the insert out.
inningsdefeat500 said:
I was usedto the one from captivate so I ordered 2 of these
http://cgi.ebay.ca/ws/eBayISAPI.dll?ViewItem&item=310404943509
Click to expand...
Click to collapse
I like having it sideways like this for a night stand clock. Does it go into clock mode when you dock it?
I like the sideways too, too bad the default OS doesn't go sideways on desktop view...
Just an update, I bought a spare charger from RND Power Solutions.....looks exactly the same as the Kidigi/Mugen charger posted on the first page. Unfortunately it will not charge batteries to 100 percent.....they only get to about 85% or so. This seems to be the issue with most of the aftermarket spare chargers out there right now. According to RND, this is because of the different voltage the S3 uses for overcharge protection and the manufacturer is working on a solution.
I'd stay away from these chargers till they get it fixed.
Man, I just want some good ones on Amazon with prime ;/
just FYI, mobilefun US and UK seems to be the same company, but all their US orders are believed to be sent from their UK location, this is not something that is stated on their US site. i ordered a case from their US site on july 8th and just received it today on the 18th, and the shipping address on the package is from their UK location.
Just got mine today. I've updated the original post with my thoughts.
I want to know if this would work with the Incipio Silicrylic two-piece case. Based on the OP's comments it sounds like it would but I'd rather not throw away $30 if it didn't.
I've had one of these stands, works with any type of phone. very very very very sturdy. I've had this for quite some time. Worked with my evo and my touchpro2:
http://www.thoughtout.biz/products/PED3.html
I ordered one and it said it was shipped on 7/3 and it's 7/22 and I still have not received it. I contacted their customer service and they've been slow to respond. Hopefully I'll be able to get my money back.
Sent from my SCH-I535 using xda app-developers app
Just looking to get an opinion if something is due-able or not. The only thing i miss on my nexus 4 to my Htc one is wireless charging (qi charging) So i have been thinking of making a qi charging case for the htc one. This shouldnt be too hard... buy a mico usb male plug
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
solder the + and - connectors to that of the NFC charging coil card (http://www.amazon.co.uk/Wireless-Ch...1&keywords=QI+Wireless+Charging+Receiver+Coil) for example and install it into a case.
Thoughts?
chambers7867 said:
Just looking to get an opinion if something is due-able or not. The only thing i miss on my nexus 4 to my Htc one is wireless charging (qi charging) So i have been thinking of making a qi charging case for the htc one. This shouldnt be too hard... buy a mico usb male plug (/snip)
solder the + and - connectors to that of the NFC charging coil card (http://www.amazon.co.uk/Wireless-Ch...1&keywords=QI+Wireless+Charging+Receiver+Coil) for example and install it into a case.
Thoughts?
Click to expand...
Click to collapse
You may encounter trouble because of the One's all-metal body. Your case will need to completely isolate the coil from the body for this to work, if memory serves me right. Admittedly, it is aluminum, so I'm not altogether certain it will be an issue.
chambers7867 said:
Just looking to get an opinion if something is due-able or not. The only thing i miss on my nexus 4 to my Htc one is wireless charging (qi charging) So i have been thinking of making a qi charging case for the htc one. This shouldnt be too hard... buy a mico usb male plug
solder the + and - connectors to that of the NFC charging coil card (http://www.amazon.co.uk/Wireless-Ch...1&keywords=QI+Wireless+Charging+Receiver+Coil) for example and install it into a case.
Thoughts?
Click to expand...
Click to collapse
I would really like to see something like this. A couple of challenges I think would be keeping the plug area on the bottom to as thin as possible and second would be to keep the case as thin and small as possible.
I wish you luck!
MG
I know this is a bit of an old post now, but I just got one of these and its working well!
http://www.ebay.com/itm/New-Wireles...Cell_Phone_PDA_Cases&var=&hash=item257fdbe5bb
how much bigger does that case make the phone?
how much bigger does that case make the phone?
Acill said:
I know this is a bit of an old post now, but I just got one of these and its working well!
http://www.ebay.com/itm/New-Wireles...Cell_Phone_PDA_Cases&var=&hash=item257fdbe5bb
Click to expand...
Click to collapse
It is Qi compatible? What charger are you using it with? It doesn't have any mention in the ad, so I'd like to make sure.
Thanks!
Acill said:
I know this is a bit of an old post now, but I just got one of these and its working well!
http://www.ebay.com/itm/New-Wireles...Cell_Phone_PDA_Cases&var=&hash=item257fdbe5bb
Click to expand...
Click to collapse
Post pics of it on the phone and let us know what kind of charger your using. It looks like you could rip off that coil and place it in any case if it's thin .
Definitely report on results. I tried to make something like this for my One XL, and while it worked as far as charging went, it was unpredictable and seemed to make the phone unstable, though I could never figure out why. I suspect it's not just the charging current but that the phone's charging circuits and drivers need to be tuned for wireless.
Qi-compatible wireless backplate
planning to replace my housing so wanted to see if while im doing that, i could use something like this inside the case or will it not work at all due to the metal?
http://www.fasttech.com/products/0/...ductive-wireless-charging-upgrade-kit-for-sam
wireless Universal Charger receiver pad Coil with Micro USB
I just received this http://www.ebay.com/itm/261348107126
you need the Type b for the HTC One, it seems to work but as it's only 500mA at 5V the charging is
going to be fairly slow
It is very slim and unnoticeable behind a tpu case, the connected usb does not stick out that far either
(about 3mm)
As it came from China it took awhile to arrive but the price is right
bexwhitt said:
I just received this http://www.ebay.com/itm/261348107126
you need the Type b for the HTC One, it seems to work but as it's only 500mA at 5V the charging is
going to be fairly slow
It is very slim and unnoticeable behind a tpu case, the connected usb does not stick out that far either
(about 3mm)
As it came from China it took awhile to arrive but the price is right
Click to expand...
Click to collapse
Thanks for letting us know about this. I'd not seen that, but it looks like just what I'd like to try and fit between my phone and case. The lack of wireless charging was the biggest reason I held off switching from my DNA to the One. I love the convenience of just plopping my phone on the orb charger during the day. The "type b" info is a big help. Much appreciated!
kit available
Anyone tried this ....
http://www.amazon.co.uk/Aftermarket...2317&sr=1-1&keywords=wireless+charger+htc+one
http://www.ebay.co.uk/itm/Type-B-Mi...lePhonesCasesPouches&var=&hash=item3a87e872ad
iOStoAndroid said:
Anyone tried this ....
http://www.amazon.co.uk/Aftermarket...2317&sr=1-1&keywords=wireless+charger+htc+one
http://www.ebay.co.uk/itm/Type-B-Mi...lePhonesCasesPouches&var=&hash=item3a87e872ad
Click to expand...
Click to collapse
I saw them but they were more expensive than the one I picked up from ebay and still come from China
they are supposedly 750mA so should be a bit quicker to charge than the 500mA one I picked up
I just received this
http://www.ebay.de/itm/111186469984...eName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
Works good, put it between my hardshell-case and the phone. Looks like the amazon-solution above is roughly the same
edit: Yeah, same as mentioned a few posts above... sorry for that. So, I can at least second that it fits quite well and doesn´t stick out much on the USB-Port
any idea how to use these universal receivers on my THL W8S?
my camera and my micro-usb port are in the same side, so the wire will cover my camera.
does anyone knows about an item that has longer wire so i can bend it around my camera?
this may not sound like the most logical idea, but isn't it possible to somehow use NFC for wireless charging, since NFC is about near field communication after all?
alireza_simkesh said:
this may not sound like the most logical idea, but isn't it possible to somehow use NFC for wireless charging, since NFC is about near field communication after all?
Click to expand...
Click to collapse
Nfc doesn't connect to the battery of the phone and the coil is not inductive as it is a derivative of close range rfid
A quick tip for the add on qi pads with the HTC one, as the USB is not in the middle you can't position the pad straight up or the curved back makes it hard to get a connection. Put it on a bit of a diagonal so the pad is in the centre of the back
Sent from my Nexus 7 using XDA Premium 4 mobile app
A lot of cool, useful information in this thread. Thanks everyone!
Hi all
I've been looking for a really cheap wireless charging pad for this amazing tablet cause they about $140 in the store by me in South Africa. I found this one but I was wondering if anyone has had experiance with it. How well does it work and how does it connect to the wall as we use different plugs in South Africa and we also work at 220v.
Basically I wanna know if it would be compatible with the tablet and with South Africa's systems?
I live in New York, USA. I bought one but it's shipping from China so it'll take a while to get to me. However, I will report back once I get it and try it out.
I'll tell you my experience but I have absolutely no idea if it'll work with South African systems / utilities / electric configurations or not.
It is powered by a USB cable. Thus, if you have a power brick that's compatible to power USB devices I'm sure it'll work fine.
P.S. As a little FYI the white version is slightly cheaper if that matters for anyone.
TheAltruistic said:
I live in New York, USA. I bought one but it's shipping from China so it'll take a while to get to me. However, I will report back once I get it and try it out.
I'll tell you my experience but I have absolutely no idea if it'll work with South African systems / utilities / electric configurations or not.
It is powered by a USB cable. Thus, if you have a power brick that's compatible to power USB devices I'm sure it'll work fine.
P.S. As a little FYI the white version is slightly cheaper if that matters for anyone.
Click to expand...
Click to collapse
Thanks man, the price makes a difference to me. I'm already like $300 over budget so $3 less for that helps. if its usb then im sorted. Please report on it when you get it. Thanks
Blade Zero (W1nst0n) said:
Thanks man, the price makes a difference to me. I'm already like $300 over budget so $3 less for that helps. if its usb then im sorted. Please report on it when you get it. Thanks
Click to expand...
Click to collapse
Took exactly 7 Business days for it to arrive to me (Ordered Aug 11th evening arrived Aug 20th). Right now it's charging my Nexus 7 (2013). It's maintaining charge rate even with the screen on the entire time (using instant messaging / texting); I'm not really using anything too battery intensive.
So far so good. I'll put it through the wringer for the next week so we'll see if it acts funny or stops working. However, for the past 30 minutes it's been okay.
What case are you using with it?
Edit: nvm, saw your other post, can you recommend a case similar to it in the same price range
Blade Zero (W1nst0n) said:
What case are you using with it?
Edit: nvm, saw your other post, can you recommend a case similar to it in the same price range
Click to expand...
Click to collapse
Yeah I'm looking for another case or possibly a sleeve. I'm seeing what turns out in a thread about the Poetic and the Moko
For those who are interested in this topic the case Blade Zero was referring to that I have was the rooCASE Dual-View which does NOT work with the CHOE Qi charger.
Blade Zero (W1nst0n) said:
Thanks man, the price makes a difference to me. I'm already like $300 over budget so $3 less for that helps. if its usb then im sorted. Please report on it when you get it. Thanks
Click to expand...
Click to collapse
So after using it for a few days, it's pretty good. I've used the CHOE with my Samsung Galaxy S III (i747) with the Qi receiver and my Nexus 7 2013
One minor annoyance is that the CHOE device itself has a blinking blue LED to indicate when it's charging. I don't know if that's something other people would like, but personally I find it redundant since my devices will say on their screen if they're charging or with an LED indicator themselves. This matters for me for 2 reasons: a) My phone blinks with a blue LED to indicate when I've received a new text message, so this throws me off there, and b) I am an energy Nazi at times, and when I see that blinking blue LED go off when I hook it up to my solar panels, I feel like that's energy not going into my battery reserves or in my phone / Nexus's battery.
The Nexus 7 2013 does charge at a decent rate, but during energy intensive operations (streaming with ChromeCast, IM chatting on Skype, and browsing the web), it did lose charge faster than it was gaining through Qi, which didn't happen under the same system demands when charging through USB cable. However, under normal use, without excessive abuse as previously mentioned, the CHOE Qi charger was able to charge up to par.
Only complaint I have is that I wish the surface of the device was some sort of rubber instead of hard plastic, because if my devices aren't on a flat surface they can easily slip out of place (or completely off the device) and discontinue charging. I've done a splendid job by jury rigging the device with rubber bands!!! :laugh: to prevent my devices from slipping off.
For a budget Qi Charger I'd say it was definitely worth it, and probably going to be harder to find a deal. It also came with a USB micro B cable with the Charger, with a length of about that of the stock Nexus 7 2013 cable.
My current Nexus 4 qi mat works perfect with my new nexus 7. Worth a look if you use multiple Android wireless charging capable devices.
http://www.gadgets4geeks.com.au/product/qi-wireless-charging-mat-pad-for-asus-google-nexus-7
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Blade Zero (W1nst0n) said:
Hi all
I've been looking for a really cheap wireless charging pad for this amazing tablet cause they about $140 in the store by me in South Africa. I found this one but I was wondering if anyone has had experiance with it. How well does it work and how does it connect to the wall as we use different plugs in South Africa and we also work at 220v.
Basically I wanna know if it would be compatible with the tablet and with South Africa's systems?
Click to expand...
Click to collapse
Look for the Morceo TX-5600. It is the EXACT same 10,000mah wireless charger as the Choe one, as they are both made by the same manufacturer.
Shipping is fast from Choe, I had mine within a week, just know that the black one has a GOLD band around the side, it is not mat or bronze like it looks in the pics, it is GOLD. At any rate, mine from China arrived in a weeks time via Amazon. The Morceo version (Identical) is on Amazon & ships from Amazon, for $60.00.
zulugod said:
My current Nexus 4 qi mat works perfect with my new nexus 7. Worth a look if you use multiple Android wireless charging capable devices.
http://www.gadgets4geeks.com.au/product/qi-wireless-charging-mat-pad-for-asus-google-nexus-7
Click to expand...
Click to collapse
That's an extraordinarily high price when you can pick up the same thing from Ebay for less than $20! My Nexus 7 goes on this one each night, with its Asus case fitted, and is fully charged by next morning:
http://www.ebay.co.uk/itm/261275119...eName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649
It's plugged into the charger that came with the Nexus.
Use Wireless charging with Slimport
Has anyone used a wireless charger with a slimport connected and outputting to a TV? The stock charger connected to the device doesn't charge my Nexus 7. It slowly discharges instead. I wanted to know if I can keep the Device on a wireless charging pad while connected to slimport.
if anyone has both the hardware, can u please try it and out provide your review.
Thanks
GSLEON3 said:
the black one has a GOLD band around the side, it is not mat or bronze like it looks in the pics, it is GOLD.
Click to expand...
Click to collapse
PIMT! I ordered the black one, as even though I like the idea of white electronics, I feel like they're too "attention-grabbing". Also, I think the black one was cheaper when I ordered it.
So I'm really missing wireless charging after having stuffed it into my GS3 and the Nexus 4 obviously having it built in. So... being that I still had 2 chargers and 2 pads left over, I've decided to begin modding the Moto X after seeing there was quite a bit of room in the bottom of the phone under the battery cover when I was replacing the woven black with a MotoMaker back. Here's the pre-fitting photos. I had to trim some of the foam away at the bottom, and still need to trace where exactly to place the wires for the charging. I'm guessing I'll have to solder directly to the back of the USB port. Where it sits will be a perfect angle, and should not interfere with NFC at all (Yay google wallet!)
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
I'll be posting periodically with updates, although I don't know when I'll have more time as I have 2 infant daughters that demand much attention.
Awesome!
I've been missing qi charging as well, hopefully you get this to work.
Sent from my XT1058 using Tapatalk
icase81 said:
I'll be posting periodically with updates, although I don't know when I'll have more time as I have 2 infant daughters that demand much attention.
Click to expand...
Click to collapse
Curious to see how this goes. Even though I am quite sure the results will be positive.
Sub'd
I hope you don't abandon the idea and keep us updated. Seems like a worthy project!
Go OP! I can't wait to see success with this, so that I may be able to do this mod myself as well.
Exactly what I was hoping someone would do. Hopefully this works out and is simple enough to do. :good:
Looks awesome, OP!
On a side note - where did you get the MotoMaker back? I'd like to change my back to a custom-colored one eventually too, but I haven't been able to find any backs online.
terabyte128 said:
Looks awesome, OP!
On a side note - where did you get the MotoMaker back? I'd like to change my back to a custom-colored one eventually too, but I haven't been able to find any backs online.
Click to expand...
Click to collapse
You can get them on ebay now. Been eyeing getting one but waiting for the wood backs.
Well this is awesome man...!!!!! :good:
Wow, god speed. I don't yet have a Moto X (still holding out for a wood back) but I'm so used to using those Palm wireless chargers on my current phone (SGS)! I have one at work and one at home on my nightstand. It's a perfect angle of inclination for my preference and the wireless charging works great. Are you having any problems putting the phone back together? I know they don't leave much room in there for something as thick as one of these chargers. And I guess if I eventually get the wood back that probably wouldn't make for an easy time getting it off :-/
I'd like to do this too, which coil receiver do you recommend?
Thanks,
Danny
dhoppy said:
I'd like to do this too, which coil receiver do you recommend?
Thanks,
Danny
Click to expand...
Click to collapse
The one he is using in the images uses the Palm Touchstone charger, you can find a bunch of applicable coils on ebay: http://www.ebay.com/bhp/palm-wireless-charging I am fairly certain that this coil will only work on that Touchstone and is not compatible with QI or Powermat.
edit: I also highly recommend buying some tiny magnets (I bought 1/4" by 1/32" circular ones) instead of the metal disks that are included so you can get it to snap a lot better to the stand.
thanks
Anyone trying this should aim to have the charging coil as close to the camera as possible, the antennas are all in the lower back of the unit and you won't want to block them at all.
I have been looking at some wireless charging options myself. One of them is a small pad that should fit under most soft cases, it has a thin ribbon cable with a very low profile micro usb connector on the end. The better option is something like that but integrated internally. I haven't opened a Moto X yet to see how much space there is. What is the maximum thickness we can hope to have, is there anywhere near 1mm if we remove the silicone pad?
Everything I am looking at is Qi compatible.
I have also been studying high-res pictures of the inside of the Moto X looking for possible solder points for power, doesn't look too friendly at this point.
Steve-x said:
Anyone trying this should aim to have the charging coil as close to the camera as possible, the antennas are all in the lower back of the unit and you won't want to block them at all.
I have been looking at some wireless charging options myself. One of them is a small pad that should fit under most soft cases, it has a thin ribbon cable with a very low profile micro usb connector on the end. The better option is something like that but integrated internally. I haven't opened a Moto X yet to see how much space there is. What is the maximum thickness we can hope to have, is there anywhere near 1mm if we remove the silicone pad?
Everything I am looking at is Qi compatible.
I have also been studying high-res pictures of the inside of the Moto X looking for possible solder points for power, doesn't look too friendly at this point.
Click to expand...
Click to collapse
There is plenty of room towards the bottom and the silicone is maybe a mm in the thickest area. Insofar as blocking the antenna, I've never had issues with my sgs3 or note 2 with putting the coil over the antenna. However, with regards to solder points, you are right. This is not going to be easy without fully disassembling and finding either the microUSB solder points or the charging circuits entry points from the microUSB. I may be abandoning this if that's the case.
Sent from my XT1060 using Tapatalk
Has anyone tried this (for the qi standard)? Thinking about giving it a shot.
http://www.ebay.com.au/itm/Universa...faultDomain_15&var&hash=item27db52d3fa&_uhb=1
the green man said:
Has anyone tried this (for the qi standard)? Thinking about giving it a shot.
http://www.ebay.com.au/itm/Universa...faultDomain_15&var&hash=item27db52d3fa&_uhb=1
Click to expand...
Click to collapse
That looks like it would be perfect to slip between the phone and a case, would bending it to conform to the back of the phone affect it's charging ability though? Or would it even be able to be bent?
"There is plenty of room towards the bottom and the silicone is maybe a mm in the thickest area. Insofar as blocking the antenna, I've never had issues with my sgs3 or note 2 with putting the coil over the antenna. However, with regards to solder points, you are right. This is not going to be easy without fully disassembling and finding either the microUSB solder points or the charging circuits entry points from the microUSB. I may be abandoning this if that's the case."
Click to expand...
Click to collapse
So how would one check to see which of the 4 prongs connected to the ribbon going to the battery are the correct +/- terminals. I've been studying over the iFixIt.com images to come up with a plan and I think if I can get a random wireless charging coil from eBay then cut that ribbon to fit into the 2 needed ports for the battery ribbon, then the only thing would be size/fitment under the back cover.
alk195 said:
That looks like it would be perfect to slip between the phone and a case, would bending it to conform to the back of the phone affect it's charging ability though? Or would it even be able to be bent?
Click to expand...
Click to collapse
It shouldn't matter. As long as the plug is in, and the pad is near the wireless charger.
This is kinda smart; can't believe this isn't widely known. I've never seen something like this.
alk195 said:
That looks like it would be perfect to slip between the phone and a case, would bending it to conform to the back of the phone affect it's charging ability though? Or would it even be able to be bent?
Click to expand...
Click to collapse
Someone has to be the guinea pig on this.. I would love to be able to slide this under a case.