Hey all,
So I received a notification for a system update to 4.4.3, and I had survival mode in SuperSU checked, so I went ahead and followed the procedure. Turns off, then reboots into TWRP. From there I reboot again using the TWRP option, and it boots into android just fine. Notification is gone, still with root. But then I go to settings >> about to find that I'm still running on 4.4.2. Manually check for update, says there isn't one available. Give it a day or so and the notification comes up again. Repeat, and same thing. I'm stuck with the notification again.
So, how do I get rid of the notification, or more preferably, how to I update to 4.4.3 keeping the root? Thanks.
UnfriendlyTurtle said:
Hey all,
So I received a notification for a system update to 4.4.3, and I had survival mode in SuperSU checked, so I went ahead and followed the procedure. Turns off, then reboots into TWRP. From there I reboot again using the TWRP option, and it boots into android just fine. Notification is gone, still with root. But then I go to settings >> about to find that I'm still running on 4.4.2. Manually check for update, says there isn't one available. Give it a day or so and the notification comes up again. Repeat, and same thing. I'm stuck with the notification again.
So, how do I get rid of the notification, or more preferably, how to I update to 4.4.3 keeping the root? Thanks.
Click to expand...
Click to collapse
You can't update the "normal way" like that with a custom recovery. When you try to do that, it tries to boot into the stock recovery to update, but since you have a custom recovery, it will fail everytime if you do it that way. What you have to do is flash the OTA zip using TWRP. You can find the OTA zip in /cache on your device. Or you can just download the update zip from these forums.
UnfriendlyTurtle said:
Hey all,
So I received a notification for a system update to 4.4.3, and I had survival mode in SuperSU checked, so I went ahead and followed the procedure. Turns off, then reboots into TWRP. From there I reboot again using the TWRP option, and it boots into android just fine. Notification is gone, still with root. But then I go to settings >> about to find that I'm still running on 4.4.2. Manually check for update, says there isn't one available. Give it a day or so and the notification comes up again. Repeat, and same thing. I'm stuck with the notification again.
So, how do I get rid of the notification, or more preferably, how to I update to 4.4.3 keeping the root? Thanks.
Click to expand...
Click to collapse
Since 4.4.4 is out, just download the full firmware package from Google and flash system, boot. Only those two.
If you don't know how to do that, the Nexus 5 forums has some great stickies that are mostly relevant to this device.
charesa39 said:
You can't update the "normal way" like that with a custom recovery. When you try to do that, it tries to boot into the stock recovery to update, but since you have a custom recovery, it will fail everytime if you do it that way. What you have to do is flash the OTA zip using TWRP. You can find the OTA zip in /cache on your device. Or you can just download the update zip from these forums.
Click to expand...
Click to collapse
Right, thanks for the information. So I repeated and booted into TWRP again. Tapped 'Install', navigated to /cache, saw a couple of folders named 'back up', 'lost+found', and then a file name of a large string of letters followed by the recognisable "razor KTU70 from KOT49H", so I went ahead and flashed the latter, checking 'verify signature'. Runs through a few commands and in a few seconds comes back as failed, so I reboot into the OS.
Any ideas?
Aerowinder said:
Since 4.4.4 is out, just download the full firmware package from Google and flash system, boot. Only those two.
If you don't know how to do that, the Nexus 5 forums has some great stickies that are mostly relevant to this device.
Click to expand...
Click to collapse
I think I have an idea, but I'll check just to be sure. Thanks for the direction.
Exactly the same for me. Installing the ota sent me to my TWRP recovery. Reboot - > still in 4.4.2.
Reading this thread, I went to TWRP recovery, installed the update from cache and like you, it failed.
Any suggestions? Did your idea work?
Where do I find the 4.4.4 mentioned here and how do I flash it in TWRP? Is install the same as flash in TWRP?
Thanks.
Anderson2 said:
Exactly the same for me. Installing the ota sent me to my TWRP recovery. Reboot - > still in 4.4.2.
Reading this thread, I went to TWRP recovery, installed the update from cache and like you, it failed.
Any suggestions? Did your idea work?
Where do I find the 4.4.4 mentioned here and how do I flash it in TWRP? Is install the same as flash in TWRP?
Thanks.
Click to expand...
Click to collapse
If it fails look to see what the specific error is. It would help to know that. If you pulled it from your cache then I assume it was downloaded by itself and should be the correct OTA. I do NOT have the "Zip file signature verification." box checked or "Enable MD5 verification of backup files." but I am extremely careful to flash/install the correct files. The OTA installed fine for me two days ago using TWRP 2.7.1.0. The 4.4.4 mentioned earlier is the factory image. You will need adb and fastboot installed on your computer to flash the factory image or any image that is pulled from inside the factory image. Wug's toolkit will work also, I think, but I've never used any toolkits. Eventually there will be a stock 4.4.4 rom that you can flash/install in TWRP but I'm not aware of one right now.
You can take the normal updates with root and TWRP (I did), but a custom kernel will prevent them from installing.
I retried to install the downloaded ota file from cache, but this time I checked zip file verification and got the error message that zip verification failed.
File name was
df43279bcf6bb6a0ae403249c3e6f314d0a7eb77.signed-razor-KTU84L-from-KOT49H.df43279b.zip
So it seems the downloaded ota file may be corrupted. How do I get my Nexus 7 2013 to re-download a new one?
(The ota download for my Nexus 5 installed with no problems - but I think it didn't go through TWRP even though TWRP is installed there too).
Thanks
---------- Post added at 04:05 AM ---------- Previous post was at 03:59 AM ----------
Further
I renamed the ota file and in settings checked for system update and got a response that my system is upto date. But it is still 4.4.2.
Need to re-download the ota. How?
Changed the system date to 2 weeks earlier and succeeded in re-downloading the ota file.
So I retried installing it and it again took me to my TWRP recovery screen. I again installed the ota from cache and again the zip verification failed : 1
And the update failed again.
Still on 4.4.2
Did not change any system files as far as I know.
Need help.
Why don't you guys download the stock firmware from Google (link in my signature), and use fastboot to flash system.img, boot.img (DO NOT run the batch file)? If it's a lack of knowledge, all you need do is ask, and I or someone else would be happy to teach you how to use it (fastboot). If you're going to be modifying your Nexus device, you need to learn fastboot. You guys have got to learn the proper way to do things.
You've put forth so much effort to fix a system that is not meant for modified (rooted, customized) phones. You can't fix it, stop trying. Just do it the proper way. And do not use a toolkit. They don't teach you anything, they spoon-feed.
Aerowinder said:
Why don't you guys download the stock firmware from Google (link in my signature), and use fastboot to flash system.img, boot.img (DO NOT run the batch file)? If it's a lack of knowledge, all you need do is ask, and I or someone else would be happy to teach you how to use it (fastboot). If you're going to be modifying your Nexus device, you need to learn fastboot. You guys have got to learn the proper way to do things.
You've put forth so much effort to fix a system that is not meant for modified (rooted, customized) phones. You can't fix it, stop trying. Just do it the proper way. And do not use a toolkit. They don't teach you anything, they spoon-feed.
Click to expand...
Click to collapse
I don't use a toolkit and would be happy to flash the system.Img and boot.img but need instructions on how to do it. You said the stock firmware link is in your signature but it isn't.
I would like to skip 4.4.3 and go directly from 4.4.2 to 4.4.4. I'm talking about a nexus 7 2013 wifi.
So I need the following information to proceed .
1. The Link to download system.img and boot.img for the nexus 7 2013 wifi. Which files exactly?
2. I have fastboot and adb installed on my windows 7 laptop because I used them (once) to root but I don't remember how I used them that one time. How exactly do I use fastboot to flash 4.4.4 ?
3. I presume I will lose root. How do I regain it after the above.
Thank you.
Anderson2 said:
I don't use a toolkit and would be happy to flash the system.Img and boot.img but need instructions on how to do it. You said the stock firmware link is in your signature but it isn't.
I would like to skip 4.4.3 and go directly from 4.4.2 to 4.4.4. I'm talking about a nexus 7 2013 wifi.
So I need the following information to proceed .
1. The Link to download system.img and boot.img for the nexus 7 2013 wifi. Which files exactly?
2. I have fastboot and adb installed on my windows 7 laptop because I used them (once) to root but I don't remember how I used them that one time. How exactly do I use fastboot to flash 4.4.4 ?
3. I presume I will lose root. How do I regain it after the above.
Thank you.
Click to expand...
Click to collapse
1. The Google firmware link in my signature is the one you want. You say you have the 2013 wifi model, aka flo, aka razor. "Factory Images "razor" for Nexus 7 [2013] (Wi-Fi)" is the proper section for you. You want 4.4.4 (KTU84P), and that's at the bottom of the razor section. Click the link to download.
2. Download the most up to date ADB/Fastboot from the link in my signature (19.0.2 (API 19)). Don't extract it yet.
3. You will lose root. Download SuperSU from my signature. 2.00 is the current version. After you download that, you can put it on your device so you can flash it in recovery in a few minutes.
The firmware you downloaded is razor-ktu84p-factory-b1b2c0da.tgz. This is a compressed archive, and you will need to extract it. If you don't know how, 7-Zip should work.
So, you've extracted the files. Delete flash-all.bat, flash-all.sh, flash-base.sh (so you don't accidentally run them).
Now, all you have left is bootloader-flo-flo-04.02.img and image-razor-ktu84p.zip.
Extract image-razor-ktu84p.zip to the current directory, so you will now have bootloader-flo-flo-04.02.img, boot.img, cache.img, recovery.img, system.img, userdata.img, android-info.txt, image-razor-ktu84p.zip in your folder.
Delete userdata.img, flashing this on accident will wipe your data. Delete image-razor-ktu84p.zip, android-info.txt, cache.img, recovery.img (this is stock recovery, you want TWRP).
Now you have boot.img, bootloader-flo-flo-04.02.img, system.img.
Remember the ADB & Fastboot zip you downloaded from my signature? Extract it to the directory with bootloader-flo-flo-04.02.img, boot.img, system.img. All 4 files. This directory now contains 7 files.
Back out of the razor-ktu84p folder. Just one step back. Now, hold shift the right-click the razor-ktu84p folder. Select Open command window here.
Reboot your device to bootloader mode. Do so by shutting it down. Then while the power is off, hold volume down and press the power button. Release these buttons when you see the big green Android.
In your command window, type the command: fastboot devices
Your device with it's serial number should show up on the list. If it does not there is a problem and you need to stop here.
If the device shows up, let's update it.
fastboot flash bootloader bootloader-flo-flo-04.02.img
<wait for it to finish>
fastboot reboot-bootloader
<wait for it to reboot>
fastboot flash system system.img
<wait for it to finish>
fastboot flash boot boot.img
<wait for it to finish>
fasboot reboot-bootloader
Done with fastboot.
At this point, enter recovery (TWRP) and wipe cache and Dalvik under advanced wipe.
Remember the SuperSU you downloaded earlier and put on your device for later? Flash that now.
Reboot, all done. Most of this is just juggling files around. If you have any questions ask.
You are wonderful aerowinder. This is just what I needed to go ahead. Thank you so much.
About your signature, it doesn't show the links when viewed in my Tapatalk version, but I went to the Web view and got it from there. (just FYI if others ask about your links).
is it possible to just flash the system img in fastboot? It's still the same bootloader, not updated? Could I just flash the whole zip by sideloading in adb and TWRP? Just a lottle confused. Thanks!
droider137 said:
is it possible to just flash the system img in fastboot? It's still the same bootloader, not updated? Could I just flash the whole zip by sideloading in adb and TWRP? Just a lottle confused. Thanks!
Click to expand...
Click to collapse
If you were already on 4.4.3, all you need to do is fastboot flash system.img, that is correct.
No, you can't flash that firmware zip in recovery.
thanks
Hi Aerowinder
Thanks again for the excellent instructions. Everything went like clockwork until it didn't ?......
I got to the point where I issued the command fastboot devices which did show the tablet serial number. But my next command to flash the bootloader img gave me the error:
Cannot open 'bootloader-flo-flo-04.02.img
(I had copy pasted the command from your instructions).
The subdirectory below the command window contains that file (one of 7 files)
Sorry. What should I do?
In case you need the info, the device screen showed
Fastboot mode
Product name - flo
Variant - flo 32G
Hw version - rev_e
Bootloader version - flo-04.02
Carrier info = none
Serial number - xxxx
Signing - yes
Secure boot enabled
Lock state - unlocked
Thanks again.
Aerowinder, you are not only an expert but an excellent teacher. Your instructions above should be a sticky.
I'm all done. Everything is fine.
The problem I had above was a file path problem. Not sure why you told me to open the command window in the parent folder. When I opened it in the folder containing the seven files all your commands worked fine. (Except for your last one where you had a spelling mistake: fasboot instead of fastboot).
Thank you very much.
Related
Hi, I was wondering if someone could make a stock img file of ww 2.13.40.13. I seem to get system errors with the pre-rooted version and it stops me from flashing back to stock with the downloaded stock files (they come as a zip file).
Even if you could send me in the right direction to make one myself, that would be helpful.
Fixed it without the image file.
Just to let others know how,
Connected via ADB and erased system, boot.img and droid_boot.img then reflashed WW versions... All working fine now but was a few hours of frustration and hair pulling... Honestly, I look like Lex Luthor...
Same problem but didn't understand your procedure
Thank you for your solution but I didn't understand
I had the same problem : I rooted my phone by flashing pre-rooted system.img. It worked but now I want to be able to update OTA. So I need to replace pre-rooted system.img with stock one.
Can you please explain how you "erased system, boot.img and droid_boot.img then reflashed WW versions"?
I tried the following : fastboot erase system, fastboot erase cache, and then adb sideload UL-Z00A-WW-2.13.40.13-user.zip with official firmware downloaded from asus.com. But now my phone is blocked on black boot screen "ASUS in search of incredible, powered by android". I can only boot to recovery. Can you repair my phone without wiping data? Thank you.
Not even any clue
So after hours of searches, the only solution I found was to flash a pre-rooted system.img back. My phone boots again normally.
But I don't have any solution to my first problem.
When I try to flash official firmware, I do:
1. In phone recovery menu : apply adb update
2. In PC terminal : adb sideload UL-Z00A-WW-2.13.40.13-user.zip
3. At around 52% transfer, error displayed on phone :
Can't install this package (Wed Apr 1 00:14:20 CST 2015) over newer build (Fri May 29 00:14:18 CST 2015)
E:Error in sideload/package.zip
(Status 7)
Installation aborted.
Has anyone succeeded in getting back to a stock system after flashing a pre-rooted one? I searched in many thread and did not found any solution.
remidem said:
So after hours of searches, the only solution I found was to flash a pre-rooted system.img back. My phone boots again normally.
But I don't have any solution to my first problem.
When I try to flash official firmware, I do:
1. In phone recovery menu : apply adb update
2. In PC terminal : adb sideload UL-Z00A-WW-2.13.40.13-user.zip
3. At around 52% transfer, error displayed on phone :
Can't install this package (Wed Apr 1 00:14:20 CST 2015) over newer build (Fri May 29 00:14:18 CST 2015)
E:Error in sideload/package.zip
(Status 7)
Installation aborted.
Has anyone succeeded in getting back to a stock system after flashing a pre-rooted one? I searched in many thread and did not found any solution.
Click to expand...
Click to collapse
Apparently you can unroot through supersu. This should then allow OTA updates...
Already tried
ultramag69 said:
Apparently you can unroot through supersu. This should then allow OTA updates...
Click to expand...
Click to collapse
No I already tried to unroot via supersu, I have the same issue. As said in thread
http://forum.xda-developers.com/zenfone2/general/asus-zenfone-2-flashing-recovery-mode-t3096596
"If you root via*METHOD 1*you can update SuperSu app as well as update binaries but*PLEASE DON'T apply any OTA updateas the phone*WILL GET STUCK IN A BOOTLOOP...Manually flash the firmware via adb..."
But it is not written how to revert METHOD 1 root.
remidem said:
No I already tried to unroot via supersu, I have the same issue. As said in thread
http://forum.xda-developers.com/zenfone2/general/asus-zenfone-2-flashing-recovery-mode-t3096596
"If you root via*METHOD 1*you can update SuperSu app as well as update binaries but*PLEASE DON'T apply any OTA updateas the phone*WILL GET STUCK IN A BOOTLOOP...Manually flash the firmware via adb..."
But it is not written how to revert METHOD 1 root.
Click to expand...
Click to collapse
From what I did, the pre-root.img was fine to OTA with as long as you don't update supersu... I flashed a pre-root.img on then applied the OTA through a 32gb or FAT32 formatted sd card and it worked fine, also took out root so you will need to put back in there if you want it....
Impossible to update with sdcard
ultramag69 said:
From what I did, the pre-root.img was fine to OTA with as long as you don't update supersu... I flashed a pre-root.img on then applied the OTA through a 32gb or FAT32 formatted sd card and it worked fine, also took out root so you will need to put back in there if you want it....
Click to expand...
Click to collapse
Thank you for your reply. I tried OTA update with sdcard:
1) In Settings/About/Software information, my current version is 2.13.40
2) I dowloaded, from http://forum.xda-developers.com/zenfone2/general/ota-links-stock-rom-t3093999 update from 2.13 to 2.14
3) Copied to external sd, in root folder, and renamed zip to MOFD_SDCARD.zip
4) Rebooted in recovery
5) Update failed. Here is my log:
Finding update package...
I:Update location: /sdcard/MOFD_SDUPDATE.zip
Opening update package...
E:file path:/sdcard/MOFD_SDUPDATE.zip
Installing update...
script aborted: Package expects build fingerprint of asus/WW_Z00A/Z00A:5.0/LRX21V/2.13.40.13_20150401_8390_user:user/release-keys or asus/WW_Z00A/Z00A:5.0/LRX21V/2.14.40.19_20150415_9660_user:user/release-keys; this device has asus/WW_Z00A/Z00A:5.0/LRX21V/2.18.40.12_20150529_9543_user:user/release-keys.
Package expects build fingerprint of asus/WW_Z00A/Z00A:5.0/LRX21V/2.13.40.13_20150401_8390_user:user/release-keys or asus/WW_Z00A/Z00A:5.0/LRX21V/2.14.40.19_20150415_9660_user:user/release-keys; this device has asus/WW_Z00A/Z00A:5.0/LRX21V/2.18.40.12_2015
E:Error in /sdcard/MOFD_SDUPDATE.zip
(Status 7)
SD Installation aborted.
This is because the version of system.img is 2.18 and the fimware version is 2.13.
Indeed I have 2 choices:
- override system with a system.img in version 2.13, but I cannot find any.
- try to apply OTA update 2.17 to 2.18 or 2.18 to 2.19 but it seems risky.
Finally I found!!! I think that a version of the firmware is tagged in system partition and another version (classically the same) is tagged in data partition (this is the one you see in Parameters -> About -> Firmware version). When I wanted to flash a firmware the same version as the one written in parameters (2.13), my phone refused to downgrade because the version of system was higher (2.18). So I had to format the system partition, apply update with official 2.18 firmware. And it worked! My phone was unrooted and I could apply method 3 root.
My issue occurred because I made the following:
1) bought a phone with a 2.13 firware
2) used it for months, applied OTA updates until 2.18
3) flashed a 2.18 pre-rooted system.img
4) used it for weeks until a made an update of supersu
5) my phone couldn't boot any more, so I wiped data (I could avoid that, if I knew!). It made a factory reset, ie get back firmware to 2.13, but system was still in 2.18
Here is the procedure to revert a phone flashed with a pre-rooted system.img (to sell it, send back to warranty, or root with another method):
1) Download official firmware from asus website in the same or higher version of your pre-rooted system.img. Do not rely on version in Parameters -> About -> Firmware version. Or simply download the latest version.
2) In your phone bootloader, enter the following commands with your PC:
fastboot erase system (I'm not sure it is necessary)
fastboot format system
3) With your phone, go into recovery menu, then to "Update with adb"
4) With your PC, go to the directory where you downloaded the firmware as zip, and enter the following command: adb sideload nom_du_fichier_teléchargé.zip
5) It takes about an hour
6) You can reboot
After that I used method 3 to root again, so that I can now OTA update exactly the same way I used to do before rooting. Moreover, I think I can update supersu as well.
tried this method, and it fails with a /sideload/package.zip error using the .18 zip. Trying to unlock as i took the .22 update... root works fine though
wrecklesswun said:
tried this method, and it fails with a /sideload/package.zip error using the .18 zip. Trying to unlock as i took the .22 update... root works fine though
Click to expand...
Click to collapse
Someone said you need to use fastboot to flash droidboot.img, boot.img, system.img and recovery.img to go back to an older version. Not sure if this works as I unlocked bootloader when I had the chance.
If you can't then you might have to wait for the "Official" unlock tool but ASUS will know and you will be out of warranty.
ultramag69 said:
Hi, I was wondering if someone could make a stock img file of ww 2.13.40.13. I seem to get system errors with the pre-rooted version and it stops me from flashing back to stock with the downloaded stock files (they come as a zip file).
Even if you could send me in the right direction to make one myself, that would be helpful.
Fixed it without the image file.
Just to let others know how,
Connected via ADB and erased system, boot.img and droid_boot.img then reflashed WW versions... All working fine now but was a few hours of frustration and hair pulling... Honestly, I look like Lex Luthor...
Click to expand...
Click to collapse
Can you please post the complete steps for the fix! Stuck here for hours, you wouldn't want to look let Lex Luthor
kamranyusuf said:
Can you please post the complete steps for the fix! Stuck here for hours, you wouldn't want to look let Lex Luthor
Click to expand...
Click to collapse
VERY IMPORTANT - Make sure you have checked the MD5 checksum on the boot, droid_boot and recovery image files as these are definitely needed to boot phone. If these are corrupt then you can brick your phone... You have been warned...
Download firmware from here-http://forum.xda-developers.com/zenfone2/orig-development/rom-pre-root-img-t3079590
It is pre-rooted but the other files needed are included in the folder.
2. Put phone in fastboot mode and erased droid_boot.img, boot.img, recovery.img and system.img using command "fastboot erase (put choice here)"
3. Flash the files I just erased back on using fast boot - "
fastboot flash recovery recovery.img
fastboot flash boot boot.img
fastboot flash fastboot droidboot.img
fastboot flash system system.img
This got me the pre-rooted 2.13.40.13. As the supersu has been inserted it is fine to use OTA to update, just make sure you don't update supersu before the OTA flash.
Good luck....
And may you retain a strand or 3 of hair like Homer Simpson....
I upgraded my phone to android EMUI8 and tried to install the RR 8.1 ROM but my device wouldn't boot up. Then I tried to reflash the stock system.img but it won't let me. I don't have TWRP on my phone but I can acces fastboot. Does anyone know what to do? Thanks in advance :^l
jetzecazemier said:
I upgraded my phone to android EMUI8 and tried to install the RR 8.1 ROM but my device wouldn't boot up. Then I tried to reflash the stock system.img but it won't let me. I don't have TWRP on my phone but I can acces fastboot. Does anyone know what to do? Thanks in advance :^l
Click to expand...
Click to collapse
What is it you mean , it won't let you. Does it give a message. Failed?
Are you at frp locked?
mrmazak said:
What is it you mean , it won't let you. Does it give a message. Failed?
Are you at frp locked?
Click to expand...
Click to collapse
Well when I try to flash the stock 8.0 system.img it gives me a "Invalid sparse file format at header magi" and when I try to flash TWRP it gives me a "FAILED (remote: partition length get error) I am frp unlocked by the way.
jetzecazemier said:
Well when I try to flash the stock 8.0 system.img it gives me a "Invalid sparse file format at header magi" and when I try to flash TWRP it gives me a "FAILED (remote: partition length get error)
Click to expand...
Click to collapse
Ok, that does not seem too bad, yet.
I suppose you are using system.img downloaded from web.
That image has given many that same error.
Best to use your system.img.
And the error flashing twrp, is common when using the nougat command or nougat recovery on Oreo.
Solutions.
Find your firmware on pro-teammt
http://pro-teammt.ru/firmware-database/?firmware_model=Bnd-&firmware_page=0
Then download update.zip
Extract files.
Get hauwei update extractor.
https://www.google.com/url?sa=t&sou...FjAAegQIARAB&usg=AOvVaw0xkKEyI85nY9x4Fjr1AWJl
Extract the system.img
Then fastboot flash it.
Recovery:
Oreo command== fastboot flash recovery_ramdisk twrp_ramdisk
Twrp name depends on version used. I use build 4 from here
https://forum.xda-developers.com/p10-lite/development/recovery-twrp-3-2-1-0-t3783447
mrmazak said:
Ok, that does not seem too bad, yet.
I suppose you are using system.img downloaded from web.
That image has given many that same error.
Best to use your system.img.
And the error flashing twrp, is common when using the nougat command or nougat recovery on Oreo.
Solutions.
Find your firmware on pro-teammt
http://pro-teammt.ru/firmware-database/?firmware_model=Bnd-&firmware_page=0
Then download update.zip
Extract files.
Get hauwei update extractor.
https://www.google.com/url?sa=t&sou...FjAAegQIARAB&usg=AOvVaw0xkKEyI85nY9x4Fjr1AWJl
Extract the system.img
Then fastboot flash it.
Recovery:
Oreo command== fastboot flash recovery_ramdisk twrp_ramdisk
Twrp name depends on version used. I use build 4 from here
https://forum.xda-developers.com/p10-lite/development/recovery-twrp-3-2-1-0-t3783447
Click to expand...
Click to collapse
Okay so I've downloaded the latest firmware for my model but when I try to extract the update.app inside of the update.zip file the huawei zip extractor gives me "RECOVERY_RAMDIS.img: Invalid header crc - Expected: 15200 Got: 44917
jetzecazemier said:
Okay so I've downloaded the latest firmware for my model but when I try to extract the update.app inside of the update.zip file the huawei zip extractor gives me "RECOVERY_RAMDIS.img: Invalid header crc - Expected: 15200 Got: 44917
Click to expand...
Click to collapse
yes there is a bug either in the extractor or the update files. they all do it. Go to the settings tab and take check mark off verify header.
mrmazak said:
yes there is a bug either in the extractor or the update files. they all do it. Go to the settings tab and take check mark off verify header.
Click to expand...
Click to collapse
I flashed the system.img but now the phone bootloops. It could be possible I got the wrong system.img because I don't know exactly what firmware my phone was on before I messed up. I only know it was EMUI8. Is there a way to completely reflash everything?
jetzecazemier said:
I flashed the system.img but now the phone bootloops. It could be possible I got the wrong system.img because I don't know exactly what firmware my phone was on before I messed up. I only know it was EMUI8. Is there a way to completely reflash everything?
Click to expand...
Click to collapse
Yes. I have guide thread here for that.
https://forum.xda-developers.com/honor-7x/how-to/guide-honor-7x-flash-oreo-update-t3781649
But also wipe in factory reset from stock recovery may solve the bootloop.
mrmazak said:
Yes. I have guide thread here for that.
https://forum.xda-developers.com/honor-7x/how-to/guide-honor-7x-flash-oreo-update-t3781649
But also wipe in factory reset from stock recovery may solve the bootloop.
Click to expand...
Click to collapse
Alright, I'll try that before I have a look at that thread
mrmazak said:
Yes. I have guide thread here for that.
https://forum.xda-developers.com/honor-7x/how-to/guide-honor-7x-flash-oreo-update-t3781649
But also wipe in factory reset from stock recovery may solve the bootloop.
Click to expand...
Click to collapse
I tried rebooting to stock recovery in order to factory reset but it only shows me the update, power off and reboot options so no factory reset possibility. I read through the entire thread you linked here but I'm very confused as to what to do with the full OTA file. I'm on a broken EMUI8 that bootloops and I'd like to clean flash EMUI8 again so I can flash an AOSP Oreo rom after that. What do I do?
jetzecazemier said:
I tried rebooting to stock recovery in order to factory reset but it only shows me the update, power off and reboot options so no factory reset possibility. I read through the entire thread you linked here but I'm very confused as to what to do with the full OTA file. I'm on a broken EMUI8 that bootloops and I'd like to clean flash EMUI8 again so I can flash an AOSP Oreo rom after that. What do I do?
Click to expand...
Click to collapse
Just made updates to guide last night. I think it is worded simple now.
Download my update "package" from step E
Extract it to a folder on your PC.
You are on emui8, so copy the HWOTA folder from the extracted zip to your sdcard
Also put hwota-update-7-8-auto.zip on sdcard.
Put the three (3) update files from pro-teammt.ru in the HWOTA8 folder on your sdcard
Put card into phone
Boot into twrp
Select install
Choose sdcard as source
Install hwota-update-7-8-auto.zip
mrmazak said:
Just made updates to guide last night. I think it is worded simple now.
Download my update "package" from step E
Extract it to a folder on your PC.
You are on emui8, so copy the HWOTA folder from the extracted zip to your sdcard
Also put hwota-update-7-8-auto.zip on sdcard.
Put the three (3) update files from pro-teammt.ru in the HWOTA8 folder on your sdcard
Put card into phone
Boot into twrp
Select install
Choose sdcard as source
Install hwota-update-7-8-auto.zip
Click to expand...
Click to collapse
So far so good but the FULLOTA update file I got from that website only has one file (update.zip) Do I need to extract that? And if so, what 3 files do I put on my sdcard?
jetzecazemier said:
So far so good but the FULLOTA update file I got from that website only has one file (update.zip) Do I need to extract that? And if so, what 3 files do I put on my sdcard?
Click to expand...
Click to collapse
No do not extract it.
On that site, next to link for update file, is "file list"
Click this. It gives links for all three files.
Put those three zip files into hwota folder
mrmazak said:
No do not extract it.
On that site, next to link for update file, is "file list"
Click this. It gives links for all three files.
Put those three zip files into hwota folder
Click to expand...
Click to collapse
Alright, I got it! Now I need to flash TWRP but the executable to install TWRP says my adb drivers are outdated. I have the minimal fastboot and adb installation from XDA.
jetzecazemier said:
Alright, I got it! Now I need to flash TWRP but the executable to install TWRP says my adb drivers are outdated. I have the minimal fastboot and adb installation from XDA.
Click to expand...
Click to collapse
That should be fine.
Usually means you have other adb also , probably from other tool.
If you have twrp , not need to use the terp recovery installer
mrmazak said:
That should be fine.
Usually means you have other adb also , probably from other tool.
If you have twrp , not need to use the terp recovery installer
Click to expand...
Click to collapse
Well the problem is I don't have TWRP and none of the versions i've tried to install work. The installer doesn't work either, it says closing adb daemon and stays on that.
jetzecazemier said:
Well the problem is I don't have TWRP and none of the versions i've tried to install work. The installer doesn't work either, it says closing adb daemon and stays on that.
Click to expand...
Click to collapse
Each step of the tool I put pause.
So it stopped on command and not closed.
Press spacebar
mrmazak said:
Each step of the tool I put pause.
So it stopped on command and not closed.
Press spacebar
Click to expand...
Click to collapse
Dude, you're the man! I got my device up and running again. I'll probably stay on EMUI8 since it's more stable than the current AOSP rom. I wanna root it tho so can I just use the lazy recovery tool to install twrp and simply install magisk?
jetzecazemier said:
Dude, you're the man! I got my device up and running again. I'll probably stay on EMUI8 since it's more stable than the current AOSP rom. I wanna root it tho so can I just use the lazy recovery tool to install twrp and simply install magisk?
Click to expand...
Click to collapse
Yes.
The lazy tool has recovery with encryption working
I got it working on EMUI8 but I decided to flash the aosp rom cuz i prefer stock android. Can't seem to get twrp to install tho. I keep getting "1 was unexpected at this time"
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page "just a sec..."
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me!!!
I try to install stock recovery and twrp with adb and huawei multi tools but it didn't work.
it shows:
"FAILED (remote: partition length get error)"
I try to unbrick my phone too but it shows same message that "FAILED (remote: partition length get error)"
Helllllp lpeaeaeaeaeaseeee!!!
Mohammadreza76646 said:
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page "just a sec..."
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me!!!
I try to install stock recovery and twrp with adb and huawei multi tools but it didn't work.
it shows:
"FAILED (remote: partition length get error)"
I try to unbrick my phone too but it shows same message that "FAILED (remote: partition length get error)"
Helllllp lpeaeaeaeaeaseeee!!!
Click to expand...
Click to collapse
Doing the update second time is fine, and best way to restore full stock. But you needed to use Oreo version of no-check recovery and the Oreo partition to flash it to.
So if still able to get into twrp, can try with correct no-check recovery and correct partition it's flashed to.
Also
With multi tool , make sure you put check mark on emui 8. Up in upper right corner. That way it uses Oreo partition names and file not nougat.
The partition length over message usually means nougat file or partition name used on Oreo system
mrmazak said:
Doing the update second time is fine, and best way to restore full stock. But you needed to use Oreo version of no-check recovery and the Oreo partition to flash it to.
So if still able to get into twrp, can try with correct no-check recovery and correct partition it's flashed to.
Also
With multi tool , make sure you put check mark on emui 8. Up in upper right corner. That way it uses Oreo partition names and file not nougat.
The partition length over message usually means nougat file or partition name used on Oreo system
Click to expand...
Click to collapse
Thank you for your answer.
But I try to extract update.app (oreo version) but its failed! huawei update extractor cant open it and 7zip cant extract it with (unexpected error...)!
And unfortunately my TWRP dos not work anymore
Mohammadreza76646 said:
Thank you for your answer.
But I try to extract update.app (oreo version) but its failed! huawei update extractor cant open it and 7zip cant extract it with (unexpected error...)!
And unfortunately my TWRP dos not work anymore
Click to expand...
Click to collapse
I give my phone to a friend to work on it. If he can't fix it I try new multi tools version to flash phone.
Mohammadreza76646 said:
Thank you for your answer.
But I try to extract update.app (oreo version) but its failed! huawei update extractor cant open it and 7zip cant extract it with (unexpected error...)!
And unfortunately my TWRP dos not work anymore
Click to expand...
Click to collapse
On the extractor app. On options tab uncheck the verify header option, it should extract then.
Then perhaps first do these three partitions.
Kernel.img
Ramdisk.img
Then
twrp_ramdisk or for stock use recovery_ramdisk
Mohammadreza76646 said:
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page "just a sec..."
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me!!!
I try to install stock recovery and twrp with adb and huawei multi tools but it didn't work.
it shows:
"FAILED (remote: partition length get error)"
I try to unbrick my phone too but it shows same message that "FAILED (remote: partition length get error)"
Helllllp lpeaeaeaeaeaseeee!!!
Click to expand...
Click to collapse
I ever have similiar problem with you dude, but it's solved now, if you always stuck on " its OK but when my phone want to start its stuck on google page "just a sec...", its call google accont verification, i'll by bypass with this script, save as to .bat and put on adb folder
adb devices
adb shell content insert --uri content://settings/secure --bind name:s:user_setup_complete --bind value:s:1
adb shell am start -n com.google.android.gsf.login/
adb shell am start -n com.google.android.gsf.login.LoginActivity
pause
in fastboot type:
fastboot -w
after all it's works to me to bypass google account verification
and if now your problem is
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
i solve with re-flash system from this
https://androidfilehost.com/?fid=673956719939830152
fastboot flash system system.img
and doing TWRP Flashing
https://forum.xda-developers.com/devdb/project/?id=25826#downloads
fastboot flash recovery_ramdisk complete_twrp_ramdisk.img
and voila my problem solved..
mrmazak said:
On the extractor app. On options tab uncheck the verify header option, it should extract then.
Then perhaps first do these three partitions.
Kernel.img
Ramdisk.img
Then
twrp_ramdisk or for stock use recovery_ramdisk
Click to expand...
Click to collapse
Hello again dude.
Finally I flashed my phone and I got the system installed.
But now my phones IMEI is lost. and I cant put sim on it!!!
what should I do now???
FRP is locked! (
Mohammadreza76646 said:
Hello again dude.
Finally I flashed my phone and I got the system installed.
But now my phones IMEI is lost. and I cant put sim on it!!!
what should I do now???
FRP is locked! (
Click to expand...
Click to collapse
So now is locked frp. Does phone have twrp or stock now.?
I think when you tried to install the oreo update for second time, you followed same tutorial as the first time. And that made you problem worse. The tutorial has you flash no-check recovery to 2 partition by block number. 22 & 29. On nougat that is "recovery" and "recovery2". On Oreo partion table it is "reserved2" & "erecovery_vendor"
I don't know how to fix imei. Have hope that if to ucan have a full ota install , maybe can be fixed.
There is available a "service rom" (used to fix most all problem) for Europe region with l21.
I can share link to site with service rom if you want , but I have not used it myself so not gonna be much help with it.
Link is to rusian language page. Google should translate for you.
https://4pda.ru/forum/index.php?showtopic=879524&view=findpost&p=73818595
mrmazak said:
So now is locked frp. Does phone have twrp or stock now.?
I think when you tried to install the oreo update for second time, you followed same tutorial as the first time. And that made you problem worse. The tutorial has you flash no-check recovery to 2 partition by block number. 22 & 29. On nougat that is "recovery" and "recovery2". On Oreo partion table it is "reserved2" & "erecovery_vendor"
I don't know how to fix imei. Have hope that if to ucan have a full ota install , maybe can be fixed.
There is available a "service rom" (used to fix most all problem) for Europe region with l21.
I can share link to site with service rom if you want , but I have not used it myself so not gonna be much help with it.
Link is to rusian language page. Google should translate for you.
https://4pda.ru/forum/index.php?showtopic=879524&view=findpost&p=73818595
Click to expand...
Click to collapse
It have stock recovery.
Mohammadreza76646 said:
It have stock recovery.
Click to expand...
Click to collapse
in summery. because i have been going back and forth in multiple different groups, multiple problem, i cant remember it all.
you have broken system, from failed root attempt, followed by failed update.
device condition is as follows.
--system not booting
--stock recovery loads
--fastboot/bootloader loads, but is in frp lock status
options are limited, at best.
I think "dload" method with service rom is best.
other option is maybe paid service like dc-unlock. But I can recall some note on there service about frp-unlock, that can only be used on device with working system. (of course if was working system, wouldn't need dc-unlock)
mrmazak said:
in summery. because i have been going back and forth in multiple different groups, multiple problem, i cant remember it all.
you have broken system, from failed root attempt, followed by failed update.
device condition is as follows.
--system not booting
--stock recovery loads
--fastboot/bootloader loads, but is in frp lock status
options are limited, at best.
I think "dload" method with service rom is best.
other option is maybe paid service like dc-unlock. But I can recall some note on there service about frp-unlock, that can only be used on device with working system. (of course if was working system, wouldn't need dc-unlock)
Click to expand...
Click to collapse
No. System boot successfully!
I will send you screenshot:
Mohammadreza76646 said:
No. System boot successfully!
I will send you screenshot:
Click to expand...
Click to collapse
here you are
Mohammadreza76646 said:
here you are
Click to expand...
Click to collapse
what about the "about phone" screen
what does it show for version?
If is all stock you should be able to go into deveolper options and enable "oem unlock". If it is greyed out and cannot switch it. Try First to remove google account (all accounts ). and reboot. See if can change then. If not, try Second to do "fastboot oem relock [enter your bootloader code here]
after relock and rebooted oem switch should be enabled again.
****RELOCK IS ONLY ADVISED IF 100% STOCK ROM****
otherwise relock could make more trouble.
Still not sure how to get IMEI back even if unlocked frp though.
**And please stop posting in other threads , the same problem , because you are getting help here.
your post in recovery thread is off topic to that thread and just makes the forum harder to maintain.
mrmazak said:
what about the "about phone" screen
what does it show for version?
If is all stock you should be able to go into deveolper options and enable "oem unlock". If it is greyed out and cannot switch it. Try First to remove google account (all accounts ). and reboot. See if can change then. If not, try Second to do "fastboot oem relock [enter your bootloader code here]
after relock and rebooted oem switch should be enabled again.
****RELOCK IS ONLY ADVISED IF 100% STOCK ROM****
otherwise relock could make more trouble.
Still not sure how to get IMEI back even if unlocked frp though.
**And please stop posting in other threads , the same problem , because you are getting help here.
your post in recovery thread is off topic to that thread and just makes the forum harder to maintain.
Click to expand...
Click to collapse
Thanks )
I'm so sorry for my posts, it's because I don't have a stable connection and I can't see notification of my thread.
I gave my phone to friend an he fix IMEI (I don't know how)
But OEM is steel lock.
I think he did it with using special box.
Mohammadreza76646 said:
Hi
I have a problem with my Honor 7X L21.
Because online update dose not work for this model I decided to updated my smartphone offline.
I downloaded Oreo update file
Unlock my phone
install twrp
update phone
every thing is going well until here
then I decided to root my phone but I saw there is no twrp on my phone
I search and I found a thread here that show how install twrp with adb use recovery ramdisk.
I install twrp on recovery ramdisk and try to root my phone. its OK but when my phone want to start its stuck on google page "just a sec..."
I boot my device on twrp and I did factory reset but the problem was still exist.
then I decided to flash update again.
I copy update file on SD card and wright code on twrp
but at the end when I reboot the recovery, twrp except stock recovery came up and my stock recovery was gone.
I reboot the system but Its loop on this page that says:
ERROR MODE
Attention!
Please update system again.
Error!
Func NO : 11 (recovery image)
Error NO : 2 (load failed!)
Please help me!!!
I try to install stock recovery and twrp with adb and huawei multi tools but it didn't work.
it shows:
"FAILED (remote: partition length get error)"
I try to unbrick my phone too but it shows same message that "FAILED (remote: partition length get error)"
Helllllp lpeaeaeaeaeaseeee!!![/QUOTE
Are u able.to boot into twrp ?
Click to expand...
Click to collapse
Hello I have a Huawei Mate-SE (with bootloader unlocked and rooted with magisk v16). I have been using the android custom rom RRO v6 (RR-O-v6.0.0-20180401-bnd-OpenKirin) for around a month now. I got this exact same problem about the White Screen saying "ERROR MODE Attention...." since I updated the Magisk to latest version (from the installed application) and rebooted my phone. SInce I rebooted I am getting that same error which makes the phone loops into it for a few times and then it loads the Huawei eRecovery that offers me some options that I am not sure what would do to my phone.
I have been trying to connect to adb tools/fastboot but it doesn't detect the phone and im pretty sure I have the device drivers installed on my computer since nothing have changed in my pc for a month now since I flashed RRO on it.
Is there any other mode besides recovery that would allow me to connect adb/fastboot to it? Or does anyone knows how should I proceed?
IonDEfeso said:
Hello I have a Huawei Mate-SE (with bootloader unlocked and rooted with magisk v16). I have been using the android custom rom RRO v6 (RR-O-v6.0.0-20180401-bnd-OpenKirin) for around a month now. I got this exact same problem about the White Screen saying "ERROR MODE Attention...." since I updated the Magisk to latest version (from the installed application) and rebooted my phone. SInce I rebooted I am getting that same error which makes the phone loops into it for a few times and then it loads the Huawei eRecovery that offers me some options that I am not sure what would do to my phone.
I have been trying to connect to adb tools/fastboot but it doesn't detect the phone and im pretty sure I have the device drivers installed on my computer since nothing have changed in my pc for a month now since I flashed RRO on it.
Is there any other mode besides recovery that would allow me to connect adb/fastboot to it? Or does anyone knows how should I proceed?
Click to expand...
Click to collapse
I have seen where the magisk update screwed up and patches the kernel intead of the ramdisk.
Power off , long press power button.
Hold volume down and plug in USB from PC.
This should cause it to boot into fastboot mode.
Then flash the stock kernel. And the stock or first patched ramdisk. (From earlier root)
mrmazak said:
I have seen where the magisk update screwed up and patches the kernel intead of the ramdisk.
Power off , long press power button.
Hold volume down and plug in USB from PC.
This should cause it to boot into fastboot mode.
Then flash the stock kernel. And the stock or first patched ramdisk. (From earlier root)
Click to expand...
Click to collapse
Hi thank you I was able to finally detect the device now. I am unsure about the kernel is that the recovery.img or system.img files I downloaded (i saved every file i used when I installed the rom) or do I need to look for the kernel somewhere else? I do have the complete_twrp_ramdisk.img file though.
Edit, I did more research and found the stock kernel is withing the boot.img file which I dont have so I looked up for the official BND-L34 oreo update and im currently downloading to extract the stock boot.img from the update.zip and flash it. Since that download was going to take me a while anyway i tried flashing the twrp recovery file without success (didn't changed anything) so i guess I should follow the instructions you gave me by flashing the kernel first then the twrp recovery.
mrmazak said:
I have seen where the magisk update screwed up and patches the kernel intead of the ramdisk.
Power off , long press power button.
Hold volume down and plug in USB from PC.
This should cause it to boot into fastboot mode.
Then flash the stock kernel. And the stock or first patched ramdisk. (From earlier root)
Click to expand...
Click to collapse
Do you know what the boot.img files name is after extraction?
I have extracted all 3 update zips and cannot find anything called boot.img
By the way, thank you.. After updating magisk I have been dealing with failed recovery and failed boot for over a week and this is the first reply anywhere that looks promising
IonDEfeso said:
Hi thank you I was able to finally detect the device now. I am unsure about the kernel is that the recovery.img or system.img files I downloaded (i saved every file i used when I installed the rom) or do I need to look for the kernel somewhere else? I do have the complete_twrp_ramdisk.img file though.
Edit, I did more research and found the stock kernel is withing the boot.img file which I dont have so I looked up for the official BND-L34 oreo update and im currently downloading to extract the stock boot.img from the update.zip and flash it. Since that download was going to take me a while anyway i tried flashing the twrp recovery file without success (didn't changed anything) so i guess I should follow the instructions you gave me by flashing the kernel first then the twrp recovery.
Click to expand...
Click to collapse
if you were on oreo. then there is not a boot.img, instaed there is seperate ramdisk.img and kernel.img.
i have all the files already extracted for oreo and a backup from nougat as well.
https://androidfilehost.com/?w=files&flid=265998
make sure you know what you are doing before flashing.
for example. on oreo the boot and recovery share one kernel image. SO if kernel is messed up you will not be able to boot "boot" or "recovery"
So after you unlocked the boot loader ( see my previous post)
you can start rooting with magisk manager / patching the boot.img from the original firmware
I used this thread in order to get root ; i modified the contents so it would fit the moto phone a bit better:, but thnx goes to Ibolito over at the pixel 3 forums
1 ) Download the latest Android factory image for your device ("see this guide on where to find it.
2 ) Extract the "boot.img" file from the downloaded image and copy it to your phone.
Warning! Make absolutely sure the firmware is exactly the same as the installed one. If not, you might loose touch.
Be aware that LMSA will download the latest firmware, even if it is not yet installed. That might break your touchscreen
Click to expand...
Click to collapse
3 ) Download latest Magisk Manager application on your phone and install it :
Link
4 )Press on the Install Magisk button (the one on the top, not the Magisk Manager), then Install > Select and Patch a File and now select the Boot.img file you extracted earlier. When the process is done, just put the patched boot.img file on your computer in the same folder as your ADB and FASTBOOT tools, the file's name is magisk_patched.img
edit: i received a comment that the name might be something like Magisk_patched_somerandomletters_.img since the latest magisk update
5 ) Enable adb debugging on your phone and connect it to your computer via USB.
Open a command prompt on your computer and migrate to the folder where the ADB and Fastboot tools are located.
(for exemple, for me it's : cd C:\adb).
7 ) Reboot your phone to fastboot by typing adb reboot bootloader
8 ) Flash the Boot.img you just patched with magisk by typing fastboot flash boot magisk_patched.img
extra: You could test a single boot with that image by typing "fastboot boot magisk_patched.img"
if it boots fine you should have root for this single boot / magisk would show as installed.
9 ) When it's done, reboot by typing fastboot reboot
10 ) Open your Magisk Manager app and check if everything is good, and it should be
extra info:
I did worry a bit because the original boot.img is 64 megs , while the patched version is only 12
but i went with it, and it was fine.
good luck to you all
Edit: rewritten entire post so it would look more like a guide, and extra warning because a lot of people seem to loose touch if they don't have the exact same firmware downloaded as on their phone.
Thanks for posting this. I unlocked my bootloader and would like to root like you did.
Do you install magisk first on your phone, then get the magisk_patched file from your phone? Or is the magisk_patched file obtained somewhere else?
testtubebaby said:
Thanks for posting this. I unlocked my bootloader and would like to root like you did.
Do you install magisk first on your phone, then get the magisk_patched file from your phone? Or is the magisk_patched file obtained somewhere else?
Click to expand...
Click to collapse
You need to install the magisk manager
In magisk manager you can click on "install (magisk)"--> "by patching a file"
then you select the file to be patched ( extracted from the original rom )
after that you can copy the patched file from your phone back to the pc and install it via fastboot.
After that magisk is installed
i hope you succeed
pjottrr said:
You need to install the magisk manager
In magisk manager you can click on "install (magisk)"--> "by patching a file"
then you select the file to be patched ( extracted from the original rom )
after that you can copy the patched file from your phone back to the pc and install it via fastboot.
After that magisk is installed
i hope you succeed
Click to expand...
Click to collapse
The firmware I see is the EU firmware. I don't see the GB firmware in the link you posted (it's RETGB). Any idea where I can find the correct firmware?
Sorry, no idea, i found the provided link via google,
testtubebaby said:
The firmware I see is the EU firmware. I don't see the GB firmware in the link you posted (it's RETGB). Any idea where I can find the correct firmware?
Click to expand...
Click to collapse
https://mirrors.lolinet.com/firmware/moto/sofiar/official/
zuggi_m said:
https://mirrors.lolinet.com/firmware/moto/sofiar/official/
Click to expand...
Click to collapse
@zuggi_m , how does posting the same url help?
i don't see a retgb here ....
Maybe someone with more dev experience can tell if you need the exact same firmware or if the version numbers are the same it is ok to use that file ?
No fastbootd?
One Hyper needs fastbootd in order to flash boot and root
mingkee said:
No fastbootd?
One Hyper needs fastbootd in order to flash boot and root
Click to expand...
Click to collapse
i don't really understand the question i guess,
a magisk patched boot is flashed via fastboot. after that you have magisk installed and root access.
pjottrr said:
i don't really understand the question i guess,
a magisk patched boot is flashed via fastboot. after that you have magisk installed and root access.
Click to expand...
Click to collapse
Yours should be G8 Power (9)
Native Android 10 uses fastbootd to flash boot, dtbo, and recovery
mingkee said:
Yours should be G8 Power (9)
Native Android 10 uses fastbootd to flash boot, dtbo, and recovery
Click to expand...
Click to collapse
maybe i'm missing your point here, my description is just so people who have to figure it out can just use my steps to get root, it is indeed based on fastboot flashing . so i'm not sure what you are trying to say, or am i misinterpreting something?
https://forum.xda-developers.com/motorola-one-hyper/development/rom-omnirom-t4044405
I did root on One Hyper (shipped with Android 10) using fastbootd method
Used old method soft brick my One Hyper
That's why I'd like to know
pjottrr said:
so after you unlocked the boot loader ( see my previous post)
you can start rooting with magisk manager / patching the boot.img from the original firmware
I used this thread in order to get root
you need to download the firmware for our device,
That can be found here;
https://mirrors.lolinet.com/firmware/moto/sofiar/official/RETEU/
after that, extract, patch, fastboot install patched version, done.
I did have some issues with the current magisk manager ( from highonandroid, i did find another source, installed version 7.5.1 of the magisk manager from this source
and that one was able to patch the boot.img
I did worry a bit because the original boot.img is 64 megs , while the patched version is only 12
but i went with it, and it was fine.
good luck to you all
Click to expand...
Click to collapse
There's a head up
US version: Sofia
The rest: Sofiar
I will buy US G Power in May and let's the fun begin
Check out One Hyper general to install Dolby Atmos and it can be toggle on/off.
Has anyone tried copying something to the root of the phone or making build.prop edits? I have the Stylus and have achieved root using the same method, however there is something not quite right with the permissions. I cannot make changes to any root files.
CCivale said:
Has anyone tried copying something to the root of the phone or making build.prop edits? I have the Stylus and have achieved root using the same method, however there is something not quite right with the permissions. I cannot make changes to any root files.
Click to expand...
Click to collapse
So you should know G Stylus ROM is Sofiap.
Be aware the way Android 10 flashing is different.
Download and install the latest ADB in order to access fastbootd (fastboot reboot fastboot) and flash boot, recovery, dtbo, vbmeta, and super
Hmmmm, I will have to read more about fastbootd in your other thread.
I did use the boot.img for the sofiap.
Hello,
I followed all the instructions in the first post and was able unlock the bootloader, install magisk, and use it to make the magisk_patched.img file from a boot.img file.
The only variation, was that I got my boot.img file from mirrors.lolinet.com/firmware/moto/sofia/official/RETUS/XT2041-4_SOFIA_RETUS_10_QPM30.80-13-2_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip since my phone is a US retail model.
After flashing, the phone boots up properly but the touchscreen does not work.
The side buttons do work and I was able to reboot into recovery. In recovery, the build on the phone is indicated as QPM30.80-51. The build in the above indicated file is QPM30.80-13-2. Could this be the source of the problem?
I have tried flashing the original boot.img (from the file above) back and the touchscreen still does not work. I have also tried “wipe data/factory reset” in recovery.
hazd said:
Hello,
I followed all the instructions in the first post and was able unlock the bootloader, install magisk, and use it to make the magisk_patched.img file from a boot.img file.
The only variation, was that I got my boot.img file from mirrors.lolinet.com/firmware/moto/sofia/official/RETUS/XT2041-4_SOFIA_RETUS_10_QPM30.80-13-2_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip since my phone is a US retail model.
After flashing, the phone boots up properly but the touchscreen does not work.
The side buttons do work and I was able to reboot into recovery. In recovery, the build on the phone is indicated as QPM30.80-51. The build in the above indicated file is QPM30.80-13-2. Could this be the source of the problem?
I have tried flashing the original boot.img (from the file above) back and the touchscreen still does not work. I have also tried “wipe data/factory reset” in recovery.
Click to expand...
Click to collapse
maybe try with the "correct" firmware? ( not sure if the minor diference changes anything, but you could try....
i found it here:
https://rsdsecure-cloud.motorola.co...ubsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
pjottrr said:
maybe try with the "correct" firmware? ( not sure if the minor diference changes anything, but you could try....
i found it here:
rsdsecure-cloud.motorola.com/download/SOFIA_RETAIL_QPM30.80-51_subsidy-DEFAULT_regulatory-DEFAULT_CFC.xml.zip
Click to expand...
Click to collapse
Thanks for finding this link.
Unfortunately i am not able to download this for some reason. I get an access denied error message.
edit:
I was able to find the most recent firmware here:
github.com/AndroidDumps/motorola_sofia_dump/tree/sofia_retail-user-10-QPM30.80-51-bd0b4-release-keys
I downloaded just the boot.img file and flashed it. That fixed the touchscreen issue. I then used magisk to batch the boot.img and I now have root.
Just to be clear, this worked on a US retail moto g power purchased unlocked from best buy. The phone model number is XT2041-4.
Hope this helps.
hazd said:
Thanks for finding this link.
Unfortunately i am not able to download this for some reason. I get an access denied error message.
edit:
I was able to find the most recent firmware here:
github.com/AndroidDumps/motorola_sofia_dump/tree/sofia_retail-user-10-QPM30.80-51-bd0b4-release-keys
I downloaded just the boot.img file and flashed it. That fixed the touchscreen issue. I then used magisk to batch the boot.img and I now have root.
Just to be clear, this worked on a US retail moto g power purchased unlocked from best buy. The phone model number is XT2041-4.
Hope this helps.
Click to expand...
Click to collapse
I downloaded the kernel and waiting for the unit.
I can flash full ROM with fastboot and fastbootd, but just flashing kernel would be much faster.
Moreover, check One Hyper general to get Dolby Atmos because you can turn on and off anytime you want.
Since you are rooted, you probably found out the OTA update won’t install.
after 3 % it crashes, and no update is installed.
So this is what I did to get the latest update:
step 1: remove root access;
- reboot and hold volume down to get into fastboot mode
- connect to pc, and load original boot.img , I checked if that was the proper one by using “fastboot boot
boot.img” ( I checked if magisk was no longer installed, this was merely to find out if I used the proper boot.img, I knew
chances the update would install were slim, I tried… but no luck as expected…. )
- I connected to LMSA, to make a backup, and download the new rom.
- I went to fastboot mode again and flashed the boot by using the command “fastboot flash boot boot.img ( the “old/current” one, not the one from the downloaded new image”
“fastboot reboot”
Step 2:
so the phone booted, and I ran the update again. This time I had no issues installing it.
Step 3:
i extracted the new Boot.img from the rom downloaded by LMSA
I re patched the new boot.img with magisk, rebooted again, and and the update was complete.
this was done on the eu g8 power , for update qpe30.79.124 , but i guess this will work on all versions since the process is the same ...
for people reading this, and don’t have root / want root, just read this thread:
Confirming success with this. I downloaded the whole ZIP, extracted boot.img and used Magisk App's built-in feature to mod the boot img. Afterward, I reflashed boot partition via fastboot. Thanks, all!
Success on Sophia RETUS 80-51-5. Flashed 80-51-3 stock boot with fastboot, took update, extracted BOOT from 80-51-5, modified with Magisk and flashed the mod with fastboot. Back up and running.
I have twrp installed. Will this work?
No, I don't believe so.
3dekstron said:
I have twrp installed. Will this work?
Click to expand...
Click to collapse
As far as I know you will also have to flash the stock recovery before updating... not sure if the recovery has to match the stock rom build, like the boot.img does. You could also flash the entire latest stock rom using LMSA to update.
pjottrr said:
Since you are rooted, you probably found out the OTA update won’t install.
after 3 % it crashes, and no update is installed.
So this is what I did to get the latest update:
step 1: remove root access;
- reboot and hold volume down to get into fastboot mode
- connect to pc, and load original boot.img , I checked if that was the proper one by using “fastboot boot
boot.img” ( I checked if magisk was no longer installed, this was merely to find out if I used the proper boot.img, I knew
chances the update would install were slim, I tried… but no luck as expected…. )
- I connected to LMSA, to make a backup, and download the new rom.
- I went to fastboot mode again and flashed the boot by using the command “fastboot flash boot boot.img ( the “old/current” one, not the one from the downloaded new image”
“fastboot reboot”
Click to expand...
Click to collapse
What does this mean (from above) and what results are to be expected?
I checked if that was the proper one by using “fastboot boot
boot.img” ( I checked if magisk was no longer installed, this was merely to find out if I used the proper boot.img, I knew
chances the update would install were slim, I tried… but no luck as expected…. )
Click to expand...
Click to collapse
I'm guessing that a fail is expected since original boot.img is no longer installed (ie, rather the patched version is installed). Hopefully someone can elaborate
Also in the case of the Magisk systemless root method, will OTA announcements occur even though they can't be installed without first unrooting?
I wonder if there is not a few steps that could be cut off and streamlined this method, for example why isnt uninstalling magisk enough, since magisk restores the boot.img, also it backs up the original boot.img so instead of going through the whole LMSA thing it can be just copied to storage and flashed in fastboot, right?
TaZeR369 said:
I wonder if there is not a few steps that could be cut off and streamlined this method, for example why isnt uninstalling magisk enough, since magisk restores the boot.img, also it backs up the original boot.img so instead of going through the whole LMSA thing it can be just copied to storage and flashed in fastboot, right?
Click to expand...
Click to collapse
I just did that with a sofia retus phone on Android 11 for the new security update.
RPM31.Q1-54-13 to RPMS31.Q1-54-13-2.
1. Uninstall all Magisk modules and reboot
2. Uninstall Magisk and hit restore image
3. Uninstall Magisk completely and phone reboots
4. Accept OTA update (nervously)
5. Patch boot image with Magisk
6. Flash patched image with minimal adb and fastboot
7. Success!
this process does replace vanced youtube with factory youtube and youtube music, but it's easy to just replace them again in vanced manager.