[Q] the tablet still on no way to turn it off - Galaxy Tab 3 Q&A, Help & Troubleshooting

Hello,
I have a galaxy tab 3.7.0 rootée.
I downloaded and I put it on the external card from my shelf a custom rom. I put my tablet in recovery mode and I made ​​a backup but instead click backup to sdcar1 I chose sdcard0. The backup stopped giving me an error then I immediately reboot the tablet but it hangs logo. I tried turning it off but no way it restarts. I like even put the tablet into recovery mode but the download mode appeared. I flashed the tablet with an official ROM "T210XXAMKE_T210OXXAMK1_XEZ" with Odin307. the flash is done successfully and tablet restarts, update and a tablet is stuck in the logo.
I do not know what to do, help me please. Thank you for reading and responding to my S.O.S
The tablet is still on, no way to turn it off.

hey
imadoid said:
Hello,
I have a galaxy tab 3.7.0 rootée.
I downloaded and I put it on the external card from my shelf a custom rom. I put my tablet in recovery mode and I made ​​a backup but instead click backup to sdcar1 I chose sdcard0. The backup stopped giving me an error then I immediately reboot the tablet but it hangs logo. I tried turning it off but no way it restarts. I like even put the tablet into recovery mode but the download mode appeared. I flashed the tablet with an official ROM "T210XXAMKE_T210OXXAMK1_XEZ" with Odin307. the flash is done successfully and tablet restarts, update and a tablet is stuck in the logo.
I do not know what to do, help me please. Thank you for reading and responding to my S.O.S
The tablet is still on, no way to turn it off.
Click to expand...
Click to collapse
i would recommend flashing the official rom again through Odin but DON'T flash the update.
There must be something in these updates that's broken because i've read quite a few posts like yours.
if anything after you get your tab working again , try to stick with philz advanced recovery, and reasearch
a CUSTOM rom instead of a Samsung update.
hope this helps :good:

moonbutt74 said:
i would recommend flashing the official rom again through Odin but DON'T flash the update.
There must be something in these updates that's broken because i've read quite a few posts like yours.
if anything after you get your tab working again , try to stick with philz advanced recovery, and reasearch
a CUSTOM rom instead of a Samsung update.
hope this helps :good:
Click to expand...
Click to collapse
thank you for your answer.mais I just flashed the tablet with an official ROM. no update. in fact, the tablet is extinguished but does not boot.
I want to know how to put the custom recovery again to be able to reflash. flash it via download only does'nt work . thank you again.

hey
imadoid said:
thank you for your answer.mais I just flashed the tablet with an official ROM. no update. in fact, the tablet is extinguished but does not boot.
I want to know how to put the custom recovery again to be able to reflash. flash it via download only does'nt work . thank you again.
Click to expand...
Click to collapse
okay so, at this point you will need to be as specific as possible in describing the problem and providing the specific
model type/number of your tab.
if i understand you, you are saying you CAN boot into Odin/Download mode BUT when you flash your custom recovery
it fails?

moonbutt74 said:
okay so, at this point you will need to be as specific as possible in describing the problem and providing the specific
model type/number of your tab.
if i understand you, you are saying you CAN boot into Odin/Download mode BUT when you flash your custom recovery
it fails?
Click to expand...
Click to collapse
exactly what happened. i can't put the costom recovery again.
SM-T210
ANDROID 4.1.2
T210XXAMKE
THANK YOU.

hey
imadoid said:
exactly what happened. i can't put the costom recovery again.
SM-T210
ANDROID 4.1.2
T210XXAMKE
THANK YOU.
Click to expand...
Click to collapse
okay so,
get this http://www.androidfilehost.com/?fid=23329332407587567
start odin, put tab in download mode [hold home,power,volume down] when warning screen appears
press appropriate button to enter download mode, connect tab, wait for it to register in odin,
select pda button in odin and navigate to the file above which you just downloaded
be sure that repartition option is NOT CHECKED, and click start.
if odin says md5 sum is invalid when you select the file, rename/remove the .md5 extension then reselect.
hope this helps.

Related

[Q] Boot Reovery Mode

Can anyone assist me with the issue of how to get this SGSIII out of boot recovery mode/
Odin gives a FAIL, PIT Partition not found error! The phone itself gives Odin: Flash read failure
N2PC Tech said:
Can anyone assist me with the issue of how to get this SGSIII out of boot recovery mode/
Odin gives a FAIL, PIT Partition not found error! The phone itself gives Odin: Flash read failure
Click to expand...
Click to collapse
Some more details would help me understand better. What I'd love to know is.
1. What is the current state of the phone ?
2. Is it rooted or Are you trying to root ? If so what process.
3. Are you trying to flash a rom or Recovery or what ?
4. Last but not least. What rom and version you currently have on there ?
Perseus71 said:
Some more details would help me understand better. What I'd love to know is.
1. What is the current state of the phone ? Stuck in "Boot recovery mode"
2. Is it rooted or Are you trying to root ? If so what process. not rooted at all.
3. Are you trying to flash a rom or Recovery or what ? was trying to install stock rom.
4. Last but not least. What rom and version you currently have on there ? I currently have no rom on here at all!
Click to expand...
Click to collapse
N2PC Tech said:
Some more details would help me understand better. What I'd love to know is.
1. What is the current state of the phone ? Stuck in "Boot recovery mode"
2. Is it rooted or Are you trying to root ? If so what process. not rooted at all.
3. Are you trying to flash a rom or Recovery or what ? was trying to install stock rom.
4. Last but not least. What rom and version you currently have on there ? I currently have no rom on here at all!
Click to expand...
Click to collapse
You didn't specify how you got here .What did you try to do, that left you in this state ? Am I assuming correctly that you somehow managed to wipe system partition and have only the stock recovery ?
If the phone is in Recovery mode, Odin will not work. You will need to reboot the phone into Download mode. To do this, you pull the battery out, volume down, home, and power button at the same time until you see the Samsung logo, and then release. You will see a warning message with bright yellow triangle and will say Downloading. Once that is done, connect to the PC.
Using ODIN, first flash a custom recovery such as TWRP. If you want to go back to stock, this is the time you flash Stock rom instead of the recovery.
If you want custom rom, copy the rom zip to the External SD card and then put that in the phone and flash via Custom Recovery.
Perseus71 said:
You didn't specify how you got here .What did you try to do, that left you in this state ? Am I assuming correctly that you somehow managed to wipe system partition and have only the stock recovery ?
If the phone is in Recovery mode, Odin will not work. You will need to reboot the phone into Download mode. To do this, you pull the battery out, volume down, home, and power button at the same time until you see the Samsung logo, and then release. You will see a warning message with bright yellow triangle and will say Downloading. Once that is done, connect to the PC.
Using ODIN, first flash a custom recovery such as TWRP. If you want to go back to stock, this is the time you flash Stock rom instead of the recovery.
If you want custom rom, copy the rom zip to the External SD card and then put that in the phone and flash via Custom Recovery.
Click to expand...
Click to collapse
Sorry.....
the phone was loading that QHSUSB_DLOAD driver on windows every time i plugged into my PC. I then tried to Odin to a Stock TMO Rom, and that was when i got the Boot recovery mode screen. i have been trying to use the buttons to get into download mode, but that doesnt work either!
N2PC Tech said:
Sorry.....
the phone was loading that QHSUSB_DLOAD driver on windows every time i plugged into my PC. I then tried to Odin to a Stock TMO Rom, and that was when i got the Boot recovery mode screen. i have been trying to use the buttons to get into download mode, but that doesnt work either!
Click to expand...
Click to collapse
QHSUSB_DLOAD means your device is hard Bricked. Please follow De-Bricking thread in this sub forum.
Perseus71 said:
QHSUSB_DLOAD means your device is hard Bricked. Please follow De-Bricking thread in this sub forum.
Click to expand...
Click to collapse
Thats how i got it out of hard brick mode. i used the sdcard image method, and that was as far as the phone went: boot recovery mode!:fingers-crossed:
N2PC Tech said:
Thats how i got it out of hard brick mode. i used the sdcard image method, and that was as far as the phone went: boot recovery mode!:fingers-crossed:
Click to expand...
Click to collapse
Then perhaps you should have asked on that thread for next steps. Anyway, if you are still getting the Qsub message when connecting to pc that means its not out of de-brick yet. I'd suggest following there.
Also please first put the phone in download mode and THEN connect to the PC. Tell me what happens in that case.
Perseus71 said:
Then perhaps you should have asked on that thread for next steps. Anyway, if you are still getting the Qsub message when connecting to pc that means its not out of de-brick yet. I'd suggest following there.
Also please first put the phone in download mode and THEN connect to the PC. Tell me what happens in that case.
Click to expand...
Click to collapse
Perhaps not Perseus! AS stated........Its out of the brick mode and is now stuck in boot recovery mode! The method to get it into download mode is null, because it will only go into the boot recovery mode when i push those buttons to try and get it there! NOTE: its now in MSM9860 when plugged into the PC.
N2PC Tech said:
Perhaps not Perseus! AS stated........Its out of the brick mode and is now stuck in boot recovery mode! The method to get it into download mode is null, because it will only go into the boot recovery mode when i push those buttons to try and get it there! NOTE: its now in MSM9860 when plugged into the PC.
Click to expand...
Click to collapse
Please note, the button combo slightly differs for Recovery versus Download mode
Recovery Booting - Power +Home + Volume UP
Download Mode - Power +Home + Volume DOWN
Do you still have the sd setup from the debrick thread? Can you see if you can get back to download mode by booting from that again?
If so, try flashing the Stock firmware again, and if you still end up in the same spot maybe try again, but this time flash CWM or TWRP recovery from Odin, then flash a Rom from recovery.
And I can't remember right off but did you try factory resetting from recovery?
Sent from my SGH-T999N using Tapatalk
Perseus71 said:
Please note, the button combo slightly differs for Recovery versus Download mode
Recovery Booting - Power +Home + Volume UP
Download Mode - Power +Home + Volume DOWN
Click to expand...
Click to collapse
Sorry, but those methods aren't and haven't worked since my phone came out of brick mode! I had already constantly tried that!
N2PC Tech said:
Sorry, but those methods aren't and haven't worked since my phone came out of brick mode! I had already constantly tried that!
Click to expand...
Click to collapse
In that Case boot the phone using the files of the SD Card as per the De-Brick Thread. See if you can into Downloading mode that way.
Perseus71 said:
In that Case boot the phone using the files of the SD Card as per the De-Brick Thread. See if you can into Downloading mode that way.
Click to expand...
Click to collapse
Tried that method also and no luck!
Just to clarify, the boot recovery mode you are referring to, does it have the binary/flash count, system status, etc? Basically what do you see?
It sounds in some ways you are in download mode, but recovery is a very different mode, so just to clear up any confusion.....
Sent from my SGH-T999N using Tapatalk

[Q] Installing custom recovery? New to Samsung phones...

Hi,
This may be a stupid question but I'm new to Samsung phones so I don't know all the details (I've only been using HTC so far).
So I've followed all the steps and got root fine. However, I tried to reboot into recovery afterwards and it's like Clockworkmod has vanished.... It just gets into what looks to me like the stock recovery. Am I doing something wrong or does the phone automatically restore its stock recovery???
Also, can someone explain to me if it is possible to manually flash a recovery from the img file using fastboot like you do on HTC phones?
Oh, and another thing. What's this Odin thing? I never used anything like that with HTC...
Thanks
ovimunt said:
Hi,
This may be a stupid question but I'm new to Samsung phones so I don't know all the details (I've only been using HTC so far).
So I've followed all the steps and got root fine. However, I tried to reboot into recovery afterwards and it's like Clockworkmod has vanished.... It just gets into what looks to me like the stock recovery. Am I doing something wrong or does the phone automatically restore its stock recovery???
Also, can someone explain to me if it is possible to manually flash a recovery from the img file using fastboot like you do on HTC phones?
Oh, and another thing. What's this Odin thing? I never used anything like that with HTC...
Thanks
Click to expand...
Click to collapse
May I ask what variant you are using? GT-i9195?
Then please boot your phone into download mode, this can be done by first switching of your phone completely then holding the power button, home button and volume down button until the download screen appears where you press continue. Once you have done that connect your phone using the usb cable and make sure all drivers have been installed! Once the drivers are installed start up Odin uncheck the f.rest time box and click the AP section and then select the recovery file provided by Sir Arco in the root thread.
If you need more help please ask, If it worked then still reply
Odin is the software used to flash files to Samsung phones.
You will need to catch the first recovery boot after flashing the recovery image, or else the stock recovery will be reflashed once the phone boots up. Just reflash the recovery via Odin and make sure to boot into recovery right after the phone reboots after the flash.
Whosat said:
Odin is the software used to flash files to Samsung phones.
You will need to catch the first recovery boot after flashing the recovery image, or else the stock recovery will be reflashed once the phone boots up. Just reflash the recovery via Odin and make sure to boot into recovery right after the phone reboots after the flash.
Click to expand...
Click to collapse
Thanks for the response. Yeah, I kind of realized that's what's happening. I've managed to boot into the custom recovery right after the flash and did what I had to do in there, but then after I reboot the phone again, the custom recovery is gone. Is there a way to stop stock recovery being reflashed automatically?
Also, if I want to install a custom kernel, how can I backup the current one so that I can restore it at a later date if I need to? I know how to do this on HTC phones but it all seems to be a bit different on Samsung and I don't want to mess up anything.
How did you reboot? If you select the reboot option in the CWM recovery,it should follow with a question on whether you want to continue rebooting with reverting to stock recovery or not.
Whosat said:
How did you reboot? If you select the reboot option in the CWM recovery,it should follow with a question on whether you want to continue rebooting with reverting to stock recovery or not.
Click to expand...
Click to collapse
Umm... yeah, I think it did ask but I just accidentally pressed no before reading what it said... So I guess I'll just have to flash the recovery again and then answer yes to that question.
Thanks
Yes that would be the correct way to do it.
Hope all goes well!

[Q] galaxy w nothing work

my galaxy w turn black and nothing work, its happened after im installing cwm. maybe because im too fast pull out usb wire. :crying: please help me. now im realize why am i doing this, after all im only 15teen. T.T help me.
bashrimuhaiedin said:
my galaxy w turn black and nothing work, its happened after im installing cwm. maybe because im too fast pull out usb wire. :crying: please help me. now im realize why am i doing this, after all im only 15teen. T.T help me.
Click to expand...
Click to collapse
your screen doesn't even turn on ?
can you post sompe picture of that?
if you can go to the download mode (VOL DOWN + HOME + POWER) flash the stock rom through odin
bashrimuhaiedin said:
my galaxy w turn black and nothing work, its happened after im installing cwm. maybe because im too fast pull out usb wire. :crying: please help me. now im realize why am i doing this, after all im only 15teen. T.T help me.
Click to expand...
Click to collapse
Hi, I had a similar problem a day ago, I corupted CWM and couldn't boot into android, When i started my phone a samsung logo appeared and then black screen, I could access download mode ( Power button, Volume - and home button ) So all you do after you enter download mode is download Odin multi downloader, and a flashable ClockworkMOD recovery, ( PM me if you want links ) and flash it into the phone, after that just reboot the phone and you will be just fine.
Press the Thanks button if i helped
Sent from my GT-I8150 using XDA-developers app
MayB4ck said:
Hi, I had a similar problem a day ago, I corupted CWM and couldn't boot into android, When i started my phone a samsung logo appeared and then black screen, I could access download mode ( Power button, Volume - and home button ) So all you do after you enter download mode is download Odin multi downloader, and a flashable ClockworkMOD recovery, ( PM me if you want links ) and flash it into the phone, after that just reboot the phone and you will be just fine.
Press the Thanks button if i helped
Sent from my GT-I8150 using XDA-developers app
Click to expand...
Click to collapse
I tried the above method, i got the attached screen. However, i can't start my phone till now. Please advise.
mohamed_fattoh said:
I tried the above method, i got the attached screen. However, i can't start my phone till now. Please advise.
Click to expand...
Click to collapse
Hey, it's seem your setting wrong, uncheck reset time.
hinfamous said:
Hey, it's seem your setting wrong, uncheck reset time.
Click to expand...
Click to collapse
I did this but, still not succeeded. Do you suggest to try to download the stock ROM instead of the CWM?
I'm trying to download the CWM not the stock ROM.
Thank you guys.
mohamed_fattoh said:
I did this but, still not succeeded. Do you suggest to try to download the stock ROM instead of the CWM?
I'm trying to download the CWM not the stock ROM.
Thank you guys.
Click to expand...
Click to collapse
Hey,
First put your phone into download mode and plug it in to your PC and make sure Odin recognizes it, then add Ancora.ops in the OPS window and the recovery.tar.md5 in the One package window. Also make sure that One package , Auto reboot and Protect OPS are checked, you should uncheck reset time because i've hear that it is causing some problems. Then just click the " Start " button and sit back, you phone will be back on in few minutes.
Just a question : Did you have any android installed when you corrupted the recovery? If yes, after you flashed the recovery the phone will reboot and will boot into android, if not then just flash the rom file if you already have one in your sdcard/internal storage.
Your phone is soft-bricked, don't worry, it will be back and running again :laugh:
I just corrupted my recovery on my phone on purpose to try if the cwm recovery works. And yes, it worked, so it should work on your phone too.
Good luck flashing your recovery, Please answer back because I want to know if this method worked.
Here are the files, just extract the rar file
Finally i have KitKat!!
Finally Solved!!!!!!!!!!!!!!!!!!!!!!!
After long days and hundred tries, it works finally. The story is as below:
1- I failed to download the CWM 6.0.4.5 directly in this state using ODIN,
2- I downloaded the stock (Yes old 2.3.6 ginger bread ROM) using ODIN. However this version keep rebooting and never completed the start up.
3- With ROM installed now (even it's not booting), i tried to download older version of CWM using ODIN (CWM 5.0.4). It was successful!!
4- I tried to do the restore for my old system, but it failed as i did backup with newer version.
5- I flashed Monster ROM (4.2.2), it works wonderful.
6- I downloaded the CWM 6.0.4.5 finally using ODIN.
7- Now i'm using 4.4.2 on my mobile finally.
Advice: Never do a flashing to your mobile when you are not fully concentrating what you are doing. Also, make sure to download the right tool and ROM for your device.
Thank you for everyone who tried to help me.
Muhammad

Soft-brick solution issue

I have left my phone off for 2 days and when i go ahead to start it up it is stuck on the "Samsung galaxy s4"
Logo. I cannot enter recovery, only download mode. I flashed .tar stock file and still that doesn't work. Can anyone help me,?
Subzero000 said:
I have left my phone off for 2 days and when i go ahead to start it up it is stuck on the "Samsung galaxy s4"
Logo. I cannot enter recovery, only download mode. I flashed .tar stock file and still that doesn't work. Can anyone help me,?
Click to expand...
Click to collapse
Flash it twice. Boot into download - Flash once. Remove Battery. Boot into download - Flash again. Don't try to boot between flashes.
Also, get your .tar from here:
http://forum.xda-developers.com/galaxy-s4-tmobile/general/firmwares-official-mdl-mk2-nb4-t2816508
Rob
rlichtefeld said:
Flash it twice. Boot into download - Flash once. Remove Battery. Boot into download - Flash again. Don't try to boot between flashes.
Also, get your .tar from here:
http://forum.xda-developers.com/galaxy-s4-tmobile/general/firmwares-official-mdl-mk2-nb4-t2816508
Rob
Click to expand...
Click to collapse
Ive tried this process a million times and ive tried it again. It isnt working, and can only go into download mode. When i try to boot into recovery it just shows the blue saying "recovery booting..." but never goes into recovery, nor does it boot. Maybe a PIT file would work? Even though i think i dont need one, idk
Subzero000 said:
Ive tried this process a million times and ive tried it again. It isnt working, and can only go into download mode. When i try to boot into recovery it just shows the blue saying "recovery booting..." but never goes into recovery, nor does it boot. Maybe a PIT file would work? Even though i think i dont need one, idk
Click to expand...
Click to collapse
Try a different computer to flash it, or it is done for. Does ODIN indicate that there was an error flashing?
There is nothing else we can do for you on this forum, if it won't flash the stock firmware. That is the last resort. The firmware has everything you should need to be able to get it back working, if it is software related. It could be hardware.
Rob
rlichtefeld said:
Try a different computer to flash it, or it is done for. Does ODIN indicate that there was an error flashing?
There is nothing else we can do for you on this forum, if it won't flash the stock firmware. That is the last resort. The firmware has everything you should need to be able to get it back working, if it is software related. It could be hardware.
Rob
Click to expand...
Click to collapse
The stock firmware is what i have been flashing and it Odin does say 'Successful'. Since it has everything i need then i guess the phone is done for i opened the phone to checke the hardware, it seems the battery is a bit swelled, do u think that may play a role in this? And when i plug it in to charge the phone doesnt show battery status picture instead, it just keeps vibrating as if i were to plug in and remove the charger. The charger is brand new btw. I really appreciate ur help Rob.
rlichtefeld said:
Try a different computer to flash it, or it is done for. Does ODIN indicate that there was an error flashing?
There is nothing else we can do for you on this forum, if it won't flash the stock firmware. That is the last resort. The firmware has everything you should need to be able to get it back working, if it is software related. It could be hardware.
Rob
Click to expand...
Click to collapse
I'm getting somewhere, it seems as if only CWM recovery and PhilZ recovery work. Twrp does not work. I installed 3 custom roms and still didnt work, i tried restoring a back up and the phone restarts in the middle of it making as if it crashes. I went into the root of the phone and i realized the only folder that DOES NOT open is the 'boot' which now i am thinking when i flash anything the boot isnt sticking. Do u know if there is a boot tar file or zip that i can flash?
Subzero000 said:
I'm getting somewhere, it seems as if only CWM recovery and PhilZ recovery work. Twrp does not work. I installed 3 custom roms and still didnt work, i tried restoring a back up and the phone restarts in the middle of it making as if it crashes. I went into the root of the phone and i realized the only folder that DOES NOT open is the 'boot' which now i am thinking when i flash anything the boot isnt sticking. Do u know if there is a boot tar file or zip that i can flash?
Click to expand...
Click to collapse
If it is the boot partition, you'll need to update the firmware, not just the ROM. You'll have to do that with ODIN and a PC, not CWM nor PhilZ. TWRP works fine as long as you use v2.8.4.0 or earlier. The v2.8.7.0 has bugs.
If you are flashing different recoveries, you should be able to flash the firmware. Again, you HAVE to flash twice in a row for it to stick. Flash with ODIN. Remove battery. Flash again. Then, boot the phone.
Rob
rlichtefeld said:
If it is the boot partition, you'll need to update the firmware, not just the ROM. You'll have to do that with ODIN and a PC, not CWM nor PhilZ. TWRP works fine as long as you use v2.8.4.0 or earlier. The v2.8.7.0 has bugs.
If you are flashing different recoveries, you should be able to flash the firmware. Again, you HAVE to flash twice in a row for it to stick. Flash with ODIN. Remove battery. Flash again. Then, boot the phone.
Rob
Click to expand...
Click to collapse
I tried the oldest twrp and doesnt work, maybe ill try 2.8.4.0. I did that with odin. As soon as it installs and vibrates and shuts the screen i remove the battery and put it back in and go back into download mode and flashed again. It still did not stick. Or should i flash, then as soon it reboots i hold down volume to enter download mode, rather than remove battery?
Subzero000 said:
I tried the oldest twrp and doesnt work, maybe ill try 2.8.4.0. I did that with odin. As soon as it installs and vibrates and shuts the screen i remove the battery and put it back in and go back into download mode and flashed again. It still did not stick. Or should i flash, then as soon it reboots i hold down volume to enter download mode, rather than remove battery?
Click to expand...
Click to collapse
Uncheck the Reboot box on ODIN. Don't let it reboot. That is the problem. '
In ODIN. Load the .tar. Uncheck Reboot.
Boot into Download mode and Flash. DO NOT REBOOT.
Pull the battery.
Wait a few minutes.
Put the battery back in.
Boot into Download Mode. Flash.
Then reboot.
There are several threads about how to do this on this section of the forum and on the General section.
Rob
rlichtefeld said:
Uncheck the Reboot box on ODIN. Don't let it reboot. That is the problem. '
In ODIN. Load the .tar. Uncheck Reboot.
Boot into Download mode and Flash. DO NOT REBOOT.
Pull the battery.
Wait a few minutes.
Put the battery back in.
Boot into Download Mode. Flash.
Then reboot.
There are several threads about how to do this on this section of the forum and on the General section.
Rob
Click to expand...
Click to collapse
I did exactly that, i waited 10 minutes with the battery removed and redid process again. Not working ? why is it only cwm working and not twrp? I wonder whats making it work...
Subzero000 said:
I did exactly that, i waited 10 minutes with the battery removed and redid process again. Not working ? why is it only cwm working and not twrp? I wonder whats making it work...
Click to expand...
Click to collapse
At this point, I have no idea. But, IIRC when you flash the firmware, it should be replacing your custom Recovery (CWM) with the Stock Recovery.
So, are you flashing CWM after you are flashing the firmware? Or, are you trying to use CWM to flash the firmware? If so, that is the issue. You have to use ODIN with a computer to flash the firmware.
CWM, Philz and TWRP are for flashing ROMs, kernels, etc, not firmware.
Rob
rlichtefeld said:
At this point, I have no idea. But, IIRC when you flash the firmware, it should be replacing your custom Recovery (CWM) with the Stock Recovery.
So, are you flashing CWM after you are flashing the firmware? Or, are you trying to use CWM to flash the firmware? If so, that is the issue. You have to use ODIN with a computer to flash the firmware.
CWM, Philz and TWRP are for flashing ROMs, kernels, etc, not firmware.
Rob
Click to expand...
Click to collapse
No, i am not flashing anything after i flash the firmware. I am using odin to flash the stock firmware. Even stock revovery doesn't work. When u flash and it attempts to boot ,it shows the blue letters 'recovery booting' with the galaxy s4 logo and stays stuck there. At this point i am very lost. Do you think it's a power button issue?
Subzero000 said:
No, i am not flashing anything after i flash the firmware. I am using odin to flash the stock firmware. Even stock revovery doesn't work. When u flash and it attempts to boot ,it shows the blue letters 'recovery booting' with the galaxy s4 logo and stays stuck there. At this point i am very lost. Do you think it's a power button issue?
Click to expand...
Click to collapse
I would not think it is the power button, since you say it does turn on. And, it does seem the Volume rocker works, since it tries to get into Recovery and does get into Download mode.
Which version of the firmware are you trying to flash?
Depending on the version of the bootloader/modems, etc. you can't downgrade versions of the firmware. You can only flash the same version or higher.
Are you flashing the 4.4.4 from here?
http://forum.xda-developers.com/galaxy-s4-tmobile/general/firmwares-official-mdl-mk2-nb4-t2816508
Are you sure you have a SGH-M919 version of the S4? If you look under the battery, it should have a sticker with that model number.
rlichtefeld said:
I would not think it is the power button, since you say it does turn on. And, it does seem the Volume rocker works, since it tries to get into Recovery and does get into Download mode.
Which version of the firmware are you trying to flash?
Depending on the version of the bootloader/modems, etc. you can't downgrade versions of the firmware. You can only flash the same version or higher.
Are you flashing the 4.4.4 from here?
http://forum.xda-developers.com/galaxy-s4-tmobile/general/firmwares-official-mdl-mk2-nb4-t2816508
Are you sure you have a SGH-M919 version of the S4? If you look under the battery, it should have a sticker with that model number.
Click to expand...
Click to collapse
I tried the firmware from that posting and dkd not work so, i went and got it from sammobile.com and still didnt work. I had this phone for 2 years and yes it is Sgh-m919 4.4.4 i had on it. And i flashed a i9505 custom rom on it through twrp and worked flawlessley. The phone was off for 2 days and i turned it on and this happened :/
rlichtefeld said:
I would not think it is the power button, since you say it does turn on. And, it does seem the Volume rocker works, since it tries to get into Recovery and does get into Download mode.
Which version of the firmware are you trying to flash?
Depending on the version of the bootloader/modems, etc. you can't downgrade versions of the firmware. You can only flash the same version or higher.
Are you flashing the 4.4.4 from here?
http://forum.xda-developers.com/galaxy-s4-tmobile/general/firmwares-official-mdl-mk2-nb4-t2816508
Are you sure you have a SGH-M919 version of the S4? If you look under the battery, it should have a sticker with that model number.
Click to expand...
Click to collapse
Sir, i after following the procedure and didnt work i left the phone battery out and phone off for 3-4 days. I put the battery in today, literally just now and it somehow worked amd booted normally... it instantly sent goosebumps throughout my body because it just seemed so odd and unexpected with no reasoning for it to work now. Do u have any idea of what it may have been?
Subzero000 said:
Sir, i after following the procedure and didnt work i left the phone battery out and phone off for 3-4 days. I put the battery in today, literally just now and it somehow worked amd booted normally... it instantly sent goosebumps throughout my body because it just seemed so odd and unexpected with no reasoning for it to work now. Do u have any idea of what it may have been?
Click to expand...
Click to collapse
I have no idea. Just thank the gods of electronics and carry on.
But, it could be some sort of hardware connection that is sometimes connected and sometimes not. You may want to start looking for a backup or spare.
Rob
rlichtefeld said:
I have no idea. Just thank the gods of electronics and carry on.
But, it could be some sort of hardware connection that is sometimes connected and sometimes not. You may want to start looking for a backup or spare.
Rob
Click to expand...
Click to collapse
Id like to thank you a lot as u are an outstanding helper on xda. I warmly appreciate your kindness to guide me through the issue. Best wishes to you

[Solved] Samsung logo keeps looping. I screwed up. Pleaaase help!

Hi good people! thanks in advance, I had a problem for about a month now where my phone (Note2) used to take about 15 min to boot, after trying many solutions, I read somewhere to delete ODEX files and after trying that in many ways I went to system/apps and deleted ODEX files there with Root Explorer which turned out to be a biiig mistake, it just stucks at the Samsung Logo for a few seconds before it starts again (only the logo, the phone doesn't reboot) and it stays like that forever. I'm in hell right now, I have some files I don't want to lose so I was afraid of factory reseting but after I was told that it won't delete them, I did but that didn't solve anything, I can't access download mode, I can access recovery mode however (not custom) I tried flashing a custom ROM but I just get "E: failed to verify whole-file signature" please help ! I'll be really thankful ! thank you !
EDIT: I hope this helps someone else, after trying everything, what eventually worked for me was the USB Jig, I was able to enter download mode and install a new ROM from there. good luck!
Landross said:
Hi good people! thanks in advance, I had a problem for about a month now where my phone (Note2) used to take about 15 min to boot, after trying many solutions, I read somewhere to delete ODEX files and after trying that in many ways I went to system/apps and deleted ODEX files there with Root Explorer which turned out to be a biiig mistake, it just stucks at the Samsung Logo for a few seconds before it starts again (only the logo, the phone doesn't reboot) and it stays like that forever. I'm in hell right now, I have some files I don't want to lose so I was afraid of factory reseting but after I was told that it won't delete them, I did but that didn't solve anything, I can't access download mode, I can access recovery mode however (not custom) I tried flashing a custom ROM but I just get "E: failed to verify whole-file signature" please help ! I'll be really thankful ! thank you !
Click to expand...
Click to collapse
If you know your rom load, flash it back on to your device without any wiping. It should load the needed files back on your system. Though any system mods will be lost.
The other option is to go into aroma from your custom recovery and grab your needed files over to your extsd card
gooberdude said:
If you know your rom load, flash it back on to your device without any wiping. It should load the needed files back on your system. Though any system mods will be lost.
The other option is to go into aroma from your custom recovery and grab your needed files over to your extsd card
Click to expand...
Click to collapse
Thanks for the reply, the problem is that I don't have a custom recovery and when I try to flash a new ROM it tells me "E: failed to verify whole-file signature" ...
Well the only option is download mode and try loading the same factory rom you have on your device. Or a newer version, if available. Some different regions have updates.
Can't use stock recovery to flash a custom rom.
You have access to a USB jig? What happens when you try to enter download mode?
gooberdude said:
Well the only option is download mode and try loading the same factory rom you have on your device. Or a newer version, if available. Some different regions have updates.
Click to expand...
Click to collapse
so sorry replying late I just saw your reply the probem is I can't access download mode I tried so many times but couldn't, I can access recovery mode however
audit13 said:
Can't use stock recovery to flash a custom rom.
You have access to a USB jig? What happens when you try to enter download mode?
Click to expand...
Click to collapse
thank you, sorry I'm replying late I just saw your reply. no I don't have access to it unfortunately, and when I try to enter download mode the phone just boots normally to the Samsung logo (where I get the usual problem)
thank you !
Remove the battery for a few seconds, replace the battery and quickly hold down the home and volume down button.
audit13 said:
Remove the battery for a few seconds, replace the battery and quickly hold down the home and volume down button.
Click to expand...
Click to collapse
Thanks ! already tried that aswell and it didn't work. tried a new battery and nothing
A USB jig may work.
audit13 said:
A USB jig may work.
Click to expand...
Click to collapse
I don't think I can get one atm I'm far away.
any help guys ?? please! I've looked everywhere still can't find a solution
Without being able to enter download mode means you can't flash a stock rom via Odin. Maybe order a jig from eBay or try yo make your own. Either way, a jig us a good tool to have when flashing Samsung phones.
audit13 said:
Without being able to enter download mode means you can't flash a stock rom via Odin. Maybe order a jig from eBay or try yo make your own. Either way, a jig us a good tool to have when flashing Samsung phones.
Click to expand...
Click to collapse
Is there any other way to fix this problem without a USB jig. ADB or something
Not sure that adb will allow you to side load a rom.
audit13 said:
Not sure that adb will allow you to side load a rom.
Click to expand...
Click to collapse
oh okay, Is installing a new ROM the only solution there is ? if it is, is the USB jig the only way to flash it? thank you !
Installation of a custom ROM but that requires a custom recovery. The easiest method would be to flash TWRP with Odin or possibly TWRP via flashify. Problem is that the phone can't enter download mode or boot the ROM.
I recommend buying or making a USB jig. If you don't want to wait, you could take the phone to a repair shop and have it flashed via jtag.
audit13 said:
Installation of a custom ROM but that requires a custom recovery. The easiest method would be to flash TWRP with Odin or possibly TWRP via flashify. Problem is that the phone can't enter download mode or boot the ROM.
I recommend buying or making a USB jig. If you don't want to wait, you could take the phone to a repair shop and have it flashed via jtag.
Click to expand...
Click to collapse
I'm gonna try to make a USB jig if that doesn't work I'll take it to a repair shop even. Can I flash a stock ROM from TWRP ? or only cutom ones ?
Thank you so much
Only custom can be installed via twrp.
audit13 said:
Only custom can be installed via twrp.
Click to expand...
Click to collapse
thank you for the help. I'll get back to you on whatever happens

Categories

Resources