Related
For those of you who keep getting stuck on the splash screen after trying to restart your phone after installing a 4.3 ROM.
My steps were (and I take no credit for this, I can't remember who had said to do this and I wasn't logged in so I couldn't click the thank you button):
*Note* If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone. The Stock ROM contains the Bootloader which should never be downgraded. Fyi: the Bootloader is not the Baseband, the Baseband is just what Modem you're using.
1. Use Odin to flash the latest stock ROM
2. Enter the stock recovery and do a factory reset and clear the cache (I did both twice just to make sure)
3. Use Odin to flash the stock rooted ROM.
4. Enter the stock recovery and do a factory reset and clear the cache. (This might not be necessary but I did anyways just to make sure)
5. Use Odin to flash a custom recovery (TWRP 2.6.0.0 was the newest recovery when I did this last week)
6. Enter the custom recovery and wipe everything, then flash whatever 4.3 based ROM and then flash GApps if you want.
*Note* It seemed like the phone was hanging on the splash screen after either the initial boot or the first restart (I can't remember which, it's been a week) but it did boot and reboot fine.
I hope this helps out some people since I found it to be quite irritating that I could install a 4.3 ROM and set everything up but when I went to restart it would hang at the splash screen (going into the recovery and clearing the cache/dalvik cache wasn't helping).
Are you basically saying to revert back to stock settings and redo the entire root process again?
Sent from my SGH-I747 using xda app-developers app
bullet2binary said:
Are you basically saying to revert back to stock settings and redo the entire root process again?
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Yeah, from what I had read that seemed to be necessary since I had used Odin to update the bootloader (MF1 since my phone is the M variant) by itself when the newest Stock ROM had come out a while ago. I still flashed the newest Stock ROM (same MF1 bootloader for the M variant) but the first time I did it I forgot to enter the Stock Recovery to do a Factory Reset and Clear the Cache and ended up stuck on the splash screen of a 4.3 ROM after flashing a custom recovery. So I needed to reflash back to stock and start over.
Going into the Stock Recovery and doing a Factory Reset and Clearing Cache is necessary and doesn't take much time at all so you may as well do it just to be sure. I also recommend backing up your IMEI if you haven't done it yet.
spongdangly said:
Yeah, from what I had read that seemed to be necessary since I had used Odin to update the bootloader (MF1 since my phone is the M variant) by itself when the newest Stock ROM had come out a while ago. I still flashed the newest Stock ROM (same MF1 bootloader for the M variant) but the first time I did it I forgot to enter the Stock Recovery to do a Factory Reset and Clear the Cache and ended up stuck on the splash screen of a 4.3 ROM after flashing a custom recovery. So I needed to reflash back to stock and start over.
Going into the Stock Recovery and doing a Factory Reset and Clearing Cache is necessary and doesn't take much time at all so you may as well do it just to be sure. I also recommend backing up your IMEI if you haven't done it yet.
Click to expand...
Click to collapse
This seems to have done the job. Running PAC 4.3 right now. I've rebooted successfully once so far.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Exactly what I ended up doing after nothing else was working. After getting it hanging the first time, even flashing 4.2 roms was giving me boot issues. After reverting back to stock and reflashing I'm now running the 9/1 Pac nightly and the 8/31 kt747 kernel.
I'm probably 10+ reboots in without issue and I flashed the kernel separately!
bullet2binary said:
This seems to have done the job. Running PAC 4.3 right now. I've rebooted successfully once so far.
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
exodus454 said:
Exactly what I ended up doing after nothing else was working. After getting it hanging the first time, even flashing 4.2 roms was giving me boot issues. After reverting back to stock and reflashing I'm now running the 9/1 Pac nightly and the 8/31 kt747 kernel.
I'm probably 10+ reboots in without issue and I flashed the kernel separately!
Click to expand...
Click to collapse
I'm glad to hear that this seems to be the proper fix. That's odd that you were having trouble with 4.2 ROMs, but then again I'd been running 4.2 ROMs on my phone since they first started rolling out. It's kind of annoying that everyone's S3 seems to be slightly different then the next.
Yeah this was a weird one all right. Just glad this post had a solution
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
glad i found this otherwise my first noob post would have truly been a noob move. Thanks wouldn't have guessed that fix for a few days at least.
verified it works. but it did require some weird time dealing with a bootloop issue on stock recoveries. had to find a .tar version of CWM to flash via odin for the final result.
Still Stuck at Splash Screen after trying to upgrade to 4.3
Background:
I had been running task's rom since 4.1.x. Upgraded to 4.2 with not problems and I kept the rom current. Tried to upgrade to 4.3 and that is where the problems started. It appeared to work, saw that Google was updating a number of apps but then then I kept getting error messages regarding various about various processes stopping unexpectedly. Rebooted the phone and it came up with Task's kernel splash screen where it remains frozen.
I can get into TWRP (v2.3.3.1) recovery and into Download mode.
I have tried wiping Cache and Dalvik Cache
I have wiped System
I have done a Factory Reset
I have Formatted Data
I have used Odin twice to get back to stock (I747UCDLK3) and both times it says "passed."
When I try to reboot it, however, it comes back to Task's Kernel splash screen (I do not see the Samsung screen)
Any help or suggestions would be great.
UPDATED: Found an older update from April and was able to restore it. Still wondering why 4.3 wouldn't take.
This Works
I was skeptical, but this actually works! Now running Task's 4.3 on my bell i747m without any problems!
Thanks for the tip OP :good:
spongdangly said:
For those of you who keep getting stuck on the splash screen after trying to restart your phone after installing a 4.3 ROM.
My steps were (and I take no credit for this, I can't remember who had said to do this and I wasn't logged in so I couldn't click the thank you button):
1. Use Odin to flash the latest stock ROM
2. Enter the stock recovery and do a factory reset and clear the cache (I did both twice just to make sure)
3. Use Odin to flash the stock rooted ROM.
4. Enter the stock recovery and do a factory reset and clear the cache. (This might not be necessary but I did anyways just to make sure)
5. Use Odin to flash a custom recovery (TWRP 2.6.0.0 was the newest recovery when I did this last week)
6. Enter the custom recovery and wipe everything, then flash whatever 4.3 based ROM and then flash GApps if you want.
*Note* It seemed like the phone was hanging on the splash screen after either the initial boot or the first restart (I can't remember which, it's been a week) but it did boot and reboot fine.
I hope this helps out some people since I found it to be quite irritating that I could install a 4.3 ROM and set everything up but when I went to restart it would hang at the splash screen (going into the recovery and clearing the cache/dalvik cache wasn't helping).
I hope I posted this in the right section but apologies if it's not.
Click to expand...
Click to collapse
If this works you're a life saver! I've been posting around 4.3 threads about this for weeks and no one came up with a decent answer....
Tried reflashing stock with root but didn't work... i'll try your way, see if that works
Gonna try this tonight!!!
Thanks!
I posted in the CM thread about this, but thought I would pass it along.. I didn't have to go back to stock non-rooted. What I did:
I odin'd Mr. Robinson's LK3 rooted
Factory reset from the 3e recovery
Rebooted
Odin'd twrp
Restored nandroid of CM
Good to go.
Solved
Thanks, also works for i727 skyrocket
wont this brick people phones flashing back 4.1.1 stock ? im on stock 4.3 stuck on samsung galaxy s3 logo meaning flashing back to latest stock rom using odin 4.1.2? 4.3 stock rom or 4.3 custom roms?
Kastro1784 said:
wont this brick people phones flashing back 4.1.1 stock ? im on stock 4.3 stuck on samsung galaxy s3 logo meaning flashing back to latest stock rom using odin 4.1.2? 4.3 stock rom or 4.3 custom roms?
Click to expand...
Click to collapse
spongdangly said:
1. Use Odin to flash the latest stock ROM
Click to expand...
Click to collapse
If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone.
I'll add a note to the OP about not attempting to downgrade to an older Stock ROM though.
spongdangly said:
If you were already on the Stock 4.3 ROM you do not want to flash the 4.0.4, 4.1.1 or 4.1.2 Stock ROM since you will brick your phone.
I'll add a note to the OP about not attempting to downgrade to an older Stock ROM though.
Click to expand...
Click to collapse
what framware did you flash to get 4.3 back working ? a leaked 4.3 Rom with no root ? thien reflash the stock 4.3 ?
Kastro1784 said:
what framware did you flash to get 4.3 back working ? a leaked 4.3 Rom with no root ? thien reflash the stock 4.3 ?
Click to expand...
Click to collapse
When I had done this back in August, I flashed the Rogers 4.1.2 Stock ROM since that was the latest stock firmware at the time and I have a Canadian S3.
If you had already flashed or been on the Stock AT&T 4.3 ROM, I'd recommend reflashing the latest Stock AT&T 4.3 ROM and following the instructions in the OP. Just make sure that you don't attempt to flash an older version of the Stock ROM that you were already on since you will brick your phone. The Stock ROM contains the bootloader and that cannot be downgraded. I don't have an American S3 since I'm Canadian so I don't know which 4.3 bootloader is the newest although I'm sure a quick search would answer that for you.
spongdangly said:
When I had done this back in August, I flashed the Rogers 4.1.2 Stock ROM since that was the latest stock firmware at the time and I have a Canadian S3.
If you had already flashed or been on the Stock AT&T 4.3 ROM, I'd recommend reflashing the latest Stock AT&T 4.3 ROM and following the instructions in the OP. Just make sure that you don't attempt to flash an older version of the Stock ROM that you were already on since you will brick your phone. The Stock ROM contains the bootloader and that cannot be downgraded. I don't have an American S3 since I'm Canadian so I don't know which 4.3 bootloader is the newest although I'm sure a quick search would answer that for you.
Click to expand...
Click to collapse
There is no latest Stock AT&T 4.3 ROM right now to reflash if you're already on the Stock AT&T 4.3 ROM. We cannot keep telling people this. If so, tell us how, because no one has, as of yet.
I've seen entirely too many posts telling people who are having trouble or phone is soft bricked on the Stock AT&T 4.3 ROM to flash or Odin back to stock. Then when asked how, the discussion ends.
That's also one of the reasons why I refuse to upgrade to 4.3 right now. At least I can still Odin back to stock as an option if something does goes wrong, but who am I to tell anyone to stay away from the latest toy, I mean update?
shortydoggg said:
There is no latest Stock AT&T 4.3 ROM right now to reflash if you're already on the Stock AT&T 4.3 ROM. We cannot keep telling people this. If so, tell us how, because no one has, as of yet.
I've seen entirely too many posts telling people who are having trouble or phone is soft bricked on the Stock AT&T 4.3 ROM to flash or Odin back to stock. Then when asked how, the discussion ends.
That's also one of the reasons why I refuse to upgrade to 4.3 right now. At least I can still Odin back to stock as an option if something does goes wrong, but who am I to tell anyone to stay away from the latest toy, I mean update?
Click to expand...
Click to collapse
I'm sorry that I'm unable to help. As I had mentioned I have a Canadian Rogers phone (since I'm in Canada) so I don't know what's going on with the AT&T Stock 4.3 ROMs other then the fact that lots of people are having problems.
If you never flashed or did an OTA update to 4.3 then I'd suggest flashing the Stock 4.1.2 ROM. That or try what Ozark_8125 did since it saves you a couple steps (just make sure that LK3 isn't an older ROM than the one you were on).
If you're unsure what bootloader is currently on your phone and your phone is rooted I'd highly recommend downloading one of the many Root Check apps from the Play Store to verify which bootloader you're currently on.
*Note* I don't know which bootloader is for the 4.1.2 AT&T ROM nor do I know which bootloader came with the 4.3 ROMs. I'm sure a simple search would answer that for you.
Ozark_8125 said:
I posted in the CM thread about this, but thought I would pass it along.. I didn't have to go back to stock non-rooted. What I did:
I odin'd Mr. Robinson's LK3 rooted
Factory reset from the 3e recovery
Rebooted
Odin'd twrp
Restored nandroid of CM
Good to go.
Click to expand...
Click to collapse
Samsung fixed my phone free thanks for the help
Sent from my SAMSUNG-SGH-I747 using Tapatalk
Hello. I just ordered my galaxy note 2 N7100 Int. version(not the n7105 lte one). I live in Greece and the phone should have arrived by 15-20 January. Even though I'm not an android noob and im using android for 2-3 years and made my own ROMs as well, I have no clue how Samsung phones work. So I would like a detailed guide please about the steps I'm will mention:
*What is the latest official firmware I can install on my N7100? How can I do that?(I'm not familiar with OTA's)
*How can I root that firmware? What is the best option for rooting it?(chainfire etc but give details on how to do it with those methods)
*Do I need to unlock my bootloader to install custom recovery and flash a rom?If so how can I do that?
*Is Philz recovery fully working and compatible with 4.4+ ROMs? If so how can I install it? If not whats the best recovery with support for 4.4+ ROMs?
*What is the best ROM with the features of Note 3?(stable no bugs good for gaming) How can I install that ROM?
*What is the best 4.4 ROM?(stable no bugs good for gaming) How can I install that ROM?
*How do I backup my IMEI?
*What is the procedure to install a ROM?(on my old phone it was : 1)Backup 2)Factory reset 3)Wipe cache,dalvik cache, system, data, and again format cache 4)Install ROM 5)Install GAPPS and reboot. Done. Are there any differences here?
I wont buy a new phone for the next 1-2 years at least so I wont my new phone to be safe when playing with custom ROMs. If you are about to comment without a detailed guide or at least telling me where to look for that guide dont comment at all, it wont help me.Thanks in advance and sorry for the trouble.
Too many questions to answer and therefore I recommend to go to the Development section for further information. Each Rom has its own install instructions, just read there and learn more about your device :good:
You can't get spoonfed here, sorry mate.
To try to answer just a few... really too many questions, you need to read a bit before posting so many questins
*What is the latest official firmware I can install on my N7100? How can I do that?(I'm not familiar with OTA's)
MKD - Indian, MK9 - european, ML3 - asian. They all work on any int 7100 model.
*Do I need to unlock my bootloader to install custom recovery and flash a rom?If so how can I do that?
You just have to root.
*What is the best ROM with the features of Note 3?(stable no bugs good for gaming) How can I install that ROM?
Most popular are DN3 and Phoenix (also maybe DR Ketan's custom ROM, but it isn't developed anymore). I personaly use Criskelo which is really stable and smooth.
*What is the procedure to install a ROM?(on my old phone it was : 1)Backup 2)Factory reset 3)Wipe cache,dalvik cache, system, data, and again format cache 4)Install ROM 5)Install GAPPS and reboot. Done. Are there any differences here?
In Phils's recovery (I recommend v 5.15, not v 6.x - because of Aroma bug) you do "prepare for ROM flashing" and then flash ROM. Erasing dalvik/system/cache etc can't hurt but is not necessary, all is done in one go. From ODIN - go to download mode, connect to PC, run ODIN and select md5 file to flash.
dalanik said:
To try to answer just a few... really too many questions, you need to read a bit before posting so many questins
*What is the latest official firmware I can install on my N7100? How can I do that?(I'm not familiar with OTA's)
MKD - Indian, MK9 - european, ML3 - asian. They all work on any int 7100 model.
*Do I need to unlock my bootloader to install custom recovery and flash a rom?If so how can I do that?
You just have to root.
*What is the best ROM with the features of Note 3?(stable no bugs good for gaming) How can I install that ROM?
Most popular are DN3 and Phoenix (also maybe DR Ketan's custom ROM, but it isn't developed anymore). I personaly use Criskelo which is really stable and smooth.
*What is the procedure to install a ROM?(on my old phone it was : 1)Backup 2)Factory reset 3)Wipe cache,dalvik cache, system, data, and again format cache 4)Install ROM 5)Install GAPPS and reboot. Done. Are there any differences here?
In Phils's recovery (I recommend v 5.15, not v 6.x - because of Aroma bug) you do "prepare for ROM flashing" and then flash ROM. Erasing dalvik/system/cache etc can't hurt but is not necessary, all is done in one go. From ODIN - go to download mode, connect to PC, run ODIN and select md5 file to flash.
Click to expand...
Click to collapse
Hey @dalanik thanks for your quick answer. I have some more questions for you. First of all, are 4.4+ roms stable for this phone for daily use and gaming? Is Philz recovery 5.15 compatible with 4.4+ roms? How do I root my device(latest official firmware) and how do I use ODIN(why is odin needed, what is odin doing)?What about backing up my IMEI? Thanks in advance.
I haven't tried 4.4 ROMs so I don't knpw. As for rooting just have a look at the forum there are several threads on rooting. Odin flashes ROMs.
Sent from my GT-N7100 using xda premium
dalanik said:
I haven't tried 4.4 ROMs so I don't knpw. As for rooting just have a look at the forum there are several threads on rooting. Odin flashes ROMs.
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
What should I use to flash roms, odin or recovery(twrp, cwm etc)?
Actually Odin can be used to flash I.e. bootloader which recovery can't. Odon is used to flash official Samsung stock ROMs in md5 format while recovery is used fir custom ROMs mostly with the Aroma installer.
Sent from my GT-N7100 using xda premium
dalanik said:
Actually Odin can be used to flash I.e. bootloader which recovery can't. Odon is used to flash official Samsung stock ROMs in md5 format while recovery is used fir custom ROMs mostly with the Aroma installer.
Sent from my GT-N7100 using xda premium
Click to expand...
Click to collapse
So to flash Phoenix ROM or DN3 or any KK ROM I dont need ODIN correct?
I think if youre on 4.1.2 you need to flash new bootloader. Each rom has instructions so hav3 a look at rom thread
Sent from my GT-N7100 using xda premium
First when arrives your phone see the firmware version, if it has 4.3 and flash custom recovery firmware etc you loose your warranty and for the moment is not possible to take warranty back. If your firmware is 4.1.2 the things are more simple you can flash everything (except 4.3 official bootloader also 4.3 official firmware witch includes bootloader) and have when you need your warranty back.
All your answers are in the forum search for start dr.ketan threads. You can start from here (old thread but very good writed for 4.1.2 there are some differences with 4.3 you have to check before act for example mobile Odin trigger the warranty at 4.3 also triangle away cannot affect knox etc etc)
http://forum.xda-developers.com/showthread.php?t=1896696
he has plenty of guides solutions etc and I think you will find many answers for your questions. Now if your phone is at 4.1.2 firmware and you want to flash 4.3, root etc or 4.3 custom rom (not all) repost to guide you how to flash and also have your warranty back.
Kaloriziko.
Sent from my GT-N7100 using Tapatalk 2
vagsvag said:
First when arrives your phone see the firmware version, if it has 4.3 and flash custom recovery firmware etc you loose your warranty and for the moment is not possible to take warranty back. If your firmware is 4.1.2 the things are more simple you can flash everything (except 4.3 official bootloader also 4.3 official firmware witch includes bootloader) and have when you need your warranty back.
All your answers are in the forum search for start dr.ketan threads. You can start from here (old thread but very good writed for 4.1.2 there are some differences with 4.3 you have to check before act for example mobile Odin trigger the warranty at 4.3 also triangle away cannot affect knox etc etc)
http://forum.xda-developers.com/showthread.php?t=1896696
he has plenty of guides solutions etc and I think you will find many answers for your questions. Now if your phone is at 4.1.2 firmware and you want to flash 4.3, root etc or 4.3 custom rom (not all) repost to guide you how to flash and also have your warranty back.
Kaloriziko.
Sent from my GT-N7100 using Tapatalk 2
Click to expand...
Click to collapse
Hello @dalanik, @vagsvag I just got my Note 2(Italy version) GT-N7100. Here's the details from the settings menu
*Android 4.1.2(gives me the ability to update to 4.3)
*Baseband N7100XXDMF1
*Kernel 3.0.31-1071214
*Build number JZO54K.N7100XXDME6
The phone is COMPLETELY stock, no root no custom recovery nothing. Can you please give me full instructions on how to install this ROM please?
About 4.4 ROMs, i have tried them.
Things that don't work:
- Bluetooth ear piece???
- Camera is not 100% stable
- I don't have sound when recording videos (Could be just me, no one else is mentioning it )
- Bad FPS in games (tried many kernels and governors, still bad. AGAIN, could be just me, no one else is mentioning it )
And that's it.
For DN3
- Root
- Flash recovery (TWRP my choice)
- Full wipe (data,system,internal storage,cache)
- Flash DN3 (you will now get a bootloop)
- Flash it ONE MORE TIME,
There is something wrong with AROMA installer, if you look closely it doesn't install the ROM for the 1st time, hence the bootloop.
Also, you DON'T NEED TO FLASH the new bootloader. I'm on the DMG1 bootloader and i'm running DN3.
If you don't flash the bootloader, you have to flash the Wi-Fi fix, to get the Wi-Fi working.
You may also experience a reboot once in a week or 2 weeks, it's random.
I personally don't want to flash the BL, because i'm terrified of ODIN. I have a bad history with it :laugh:
Mashed_Potatoes said:
About 4.4 ROMs, i have tried them.
Things that don't work:
- Bluetooth ear piece???
- Camera is not 100% stable
- I don't have sound when recording videos (Could be just me, no one else is mentioning it )
- Bad FPS in games (tried many kernels and governors, still bad. AGAIN, could be just me, no one else is mentioning it )
And that's it.
For DN3
- Root
- Flash recovery (TWRP my choice)
- Full wipe (data,system,internal storage,cache)
- Flash DN3 (you will now get a bootloop)
- Flash it ONE MORE TIME,
There is something wrong with AROMA installer, if you look closely it doesn't install the ROM for the 1st time, hence the bootloop.
Also, you DON'T NEED TO FLASH the new bootloader. I'm on the DMG1 bootloader and i'm running DN3.
If you don't flash the bootloader, you have to flash the Wi-Fi fix, to get the Wi-Fi working.
You may also experience a reboot once in a week or 2 weeks, it's random.
I personally don't want to flash the BL, because i'm terrified of ODIN. I have a bad history with it :laugh:
Click to expand...
Click to collapse
@Mashed_Potatoes thanks for your reply but please make things a little bit more detailed..
- Root -- how can I root my device? Link?
- Flash recovery (TWRP my choice)? I want Philz recovery. How do I flash it? Is there any problems with flashing DN3 with Philz recovery?
-What are the prerequisites to get DN3 ROM to work FULLY? Have you noticed any important bugs while using it? What bootloader do I have to flash to get DN3 ROM to work? How can I flash that bootloader? Remember I'm on stock 4.1.2
-How can I access Recovery on this phone?
NickVXD said:
@Mashed_Potatoes thanks for your reply but please make things a little bit more detailed..
- Root -- how can I root my device? Link?
- Flash recovery (TWRP my choice)? I want Philz recovery. How do I flash it? Is there any problems with flashing DN3 with Philz recovery?
-What are the prerequisites to get DN3 ROM to work FULLY? Have you noticed any important bugs while using it? What bootloader do I have to flash to get DN3 ROM to work? How can I flash that bootloader? Remember I'm on stock 4.1.2
-How can I access Recovery on this phone?
Click to expand...
Click to collapse
You need to use the search option.
http://forum.xda-developers.com/showthread.php?t=2143479 - How to root
http://www.youtube.com/watch?v=RKfURLDlCRg - How to flash recovery
I don't know about Philz i had it before TWRP but that was before DN3 existed =D
I found no bugs in DN3, its a bit slower than 4.1.2 and the ram usage is higher
You flash the bootloader through ODIN too but i cant help you about that i don't know
Once you root your phone download an app called Quick Boot which will allow you to access Download and Recovery modes with one click
Hey guys I need a little bit more help.
@Androidwizzard @dalanik @vagsvag
I successfully rooted my device with CF and ODIN and now I installed latest Philz recovery as well.
One last question.. I'm now on official 4.1.2(again xD)and like I have said again I want to install DN3 ROM.. What bootloader do I need to flash to get DN3 to work?How do I know what bootloader Im using right now?
What I think the procedure is
1)Install 4.3 bootloader while running 4.1.2
2)Make a backup with Philz recovery
3)Full wipe and install 4.3 DN3 ROM.
Is this correct? Dont forget to answer the other things I asked you!! Thanks in advance!!
NickVXD said:
Hey guys I need a little bit more help.
@Androidwizzard @dalanik @vagsvag
I successfully rooted my device with CF and ODIN and now I installed latest Philz recovery as well.
One last question.. I'm now on official 4.1.2(again xD)and like I have said again I want to install DN3 ROM.. What bootloader do I need to flash to get DN3 to work?How do I know what bootloader Im using right now?
What I think the procedure is
1)Install 4.3 bootloader while running 4.1.2
2)Make a backup with Philz recovery
3)Full wipe and install 4.3 DN3 ROM.
Is this correct? Dont forget to answer the other things I asked you!! Thanks in advance!!
Click to expand...
Click to collapse
There is only ONE bootloader you can flash that is KNOX-Free, and that is MJ5. All other bootloaders have KNOX. Do not use Wi-Fi fix as that will fix your Wi-fi but may introduce instability, reboots, etc. Well, not the Fix, the fix is fine, but the rest of the old bootloader. Just flash MJ5.
I'd do backup FIRST and then flash bootloader.
dalanik said:
There is only ONE bootloader you can flash that is KNOX-Free, and that is MJ5. All other bootloaders have KNOX. Do not use Wi-Fi fix as that will fix your Wi-fi but may introduce instability, reboots, etc. Well, not the Fix, the fix is fine, but the rest of the old bootloader. Just flash MJ5.
I'd do backup FIRST and then flash bootloader.
Click to expand...
Click to collapse
What is KNOX? If I flash MJ5 while running 4.1.2 and then flash DN3 are there going to be any problems?(instabilities wifi issues etc)Also how do I backup my bootloader? And what bootloader am I running now?
NickVXD said:
Hey guys I need a little bit more help.
I successfully rooted my device with CF and ODIN and now I installed latest Philz recovery as well.
One last question.. I'm now on official 4.1.2(again xD)and like I have said again I want to install DN3 ROM.. What bootloader do I need to flash to get DN3 to work?How do I know what bootloader Im using right now?
What I think the procedure is
1)Install 4.3 bootloader while running 4.1.2
2)Make a backup with Philz recovery
3)Full wipe and install 4.3 DN3 ROM.
Is this correct? Dont forget to answer the other things I asked you!! Thanks in advance!!
Click to expand...
Click to collapse
FIRST of ALL: Don't use the latest Philz, RUN 5.15 is the best way to flash 4.3 custom roms with Aroma installer!
As mentioned: You got to take MJ5 if you ever want to go back to stock 4.1.2 at any time, besides you won't have wifi issue.
Only way to change bootloader: PC Odin.
Befor starting to install a custom rom read the instructions on the OP of the desired rom. There you find all necessary wipes to do :good:
Androidwizzard said:
FIRST of ALL: Don't use the latest Philz, RUN 5.15 is the best way to flash 4.3 custom roms with Aroma installer!
As mentioned: You got to take MJ5 if you ever want to go back to stock 4.1.2 at any time, besides you won't have wifi issue.
Only way to change bootloader: PC Odin.
Befor starting to install a custom rom read the instructions on the OP of the desired rom. There you find all necessary wipes to do :good:
Click to expand...
Click to collapse
@Androidwizzard so to flash DN3 ROM this is what I have to do:
1)Flash Philz 5.15 recovery with ODIN
2)Flash MJ5 bootloader while running official 4.1.2
3)Make a backup of current with recovery
4)Make the necessary wipes with recovery and flash DN3 ROM
Is everything I mentioned above correct?
Also how do I go back COMPLETELY stock if I ever want?
And btw is DN3 ROM good for games? I play lots of heavy games like GTA:SA etc..
Thanks A LOT guys for helping me, I know I'm annoying but I'm really new to Samsung and this all seems really strange
NickVXD said:
@Androidwizzard so to flash DN3 ROM this is what I have to do:
1)Flash Philz 5.15 recovery with ODIN
2)Flash MJ5 bootloader while running official 4.1.2
3)Make a backup of current with recovery
4)Make the necessary wipes with recovery and flash DN3 ROM
Is everything I mentioned above correct?
Also how do I go back COMPLETELY stock if I ever want?
And btw is DN3 ROM good for games? I play lots of heavy games like GTA:SA etc..
Thanks A LOT guys for helping me, I know I'm annoying but I'm really new to Samsung and this all seems really strange
Click to expand...
Click to collapse
Here you find all you need from the godfather Dr Ketan:
http://forum.xda-developers.com/showpost.php?p=48032704&postcount=4753
There are several links and guides, :good:
Hello, I recently just updated my Rogers SGH-i317M to 4.3, which then downloaded a system update which put it at 4.4. I was running Jedi X20, which is based on 4.1.2, when I first tried updating, I flashed the "4.3param_tz" file in odin, and was left with an error screen saying I need to recover using Kies, so I downloaded the official release, flashed via odin, and thats how I got to where I am now. I want to try the "Ditto Note 3" rom, "Sky Note Air 4.3", "Mean Bean" and "Beanstalk". My main question is, can I just start flashing these roms like I was before on 4.1.2, or do I need to use the specific kernel listed on their page? Before you needed a specific kernel to run a touchwiz rom or an aosp rom, so is it still the same? Or can I use my stock 4.4 kernel and try both aosp and tw roms now? If so could you point out the kernels I would need? And educate me on anything else I should know about before flashing 4.3 and 4.4 roms, (I'm not worried about warranty), this would be greatly appreciated. Thanks for your time in reading this and helping me out, much appreciated!!
Regardless of where u are, I'd Odin to Rogers stock KK 4.4.2. Then Odin Twrp recovery, boot into twrp recovery and flash SU v.1.99. Finally choose your rom and flash away. This way you are on the lastest KK 4.4.2 Bootloader and KK Modem/Baseband.
just_visiting said:
Regardless of where u are, I'd Odin to Rogers stock KK 4.4.2. Then Odin Twrp recovery, boot into twrp recovery and flash SU v.1.99. Finally choose your rom and flash away. This way you are on the lastest KK 4.4.2 Bootloader and KK Modem/Baseband.
Click to expand...
Click to collapse
I did all that except flash SU 1.99, so I tried flashing SKynote Air and it didnt work, upon restarting my phone it said no os is available. So I tried restoring from the backup I made of the official 4.4.2 Samsung rom in twrp, didn't work. Tried Odin, didn't work. Then I tried flashing the Skynote rom again and it worked. So I'm afraid of flashing any other roms now.
Hi guys, i have a very strange problem with my Note 2 when trying to upgrade from Hurricane 4.3 to Phantom 4.4.2. or Dr Ketan Custom ROMV8 4.4.2.
No matter if i use TWRP latest or Phils latest recovery it just stop at Samsung logo.
I have tried with both Mj5 and Nd3 bootloader, both compatible with 4.4.2 and i do all the wiping needed before i flash.
Md5 is checked on all files.
I have tried this atleast 10 times but always ending up with nandroid back to Hurricane.
nobad said:
Hi guys, i have a very strange problem with my Note 2 when trying to upgrade from Hurricane 4.3 to Phantom 4.4.2. or Dr Ketan Custom ROMV8 4.4.2.
No matter if i use TWRP latest or Phils latest recovery it just stop at Samsung logo.
I have tried with both Mj5 and Nd3 bootloader, both compatible with 4.4.2 and i do all the wiping needed before i flash.
Md5 is checked on all files.
I have tried this atleast 10 times but always ending up with nandroid back to Hurricane.
Click to expand...
Click to collapse
In that case flash 4.4.2 stock rom , root it and then flash custom rom.
Sent from my GT-N7100 using Tapatalk
Just to be precise: Flash stock rom 4.4.2 as suggested and afterwards a custom recovery, both using Odin, no need to root. Then you can flash any rom you like :good:
Androidwizzard said:
Just to be precise: Flash stock rom 4.4.2 as suggested and afterwards a custom recovery, both using Odin, no need to root. Then you can flash any rom you like :good:
Click to expand...
Click to collapse
Thank you for your answer, can i flash any 4.4.2 ROM since no NEE (nordic countrys) out yet, France or Gremany per exemple?
nobad said:
Thank you for your answer, can i flash any 4.4.2 ROM since no NEE (nordic countrys) out yet, France or Gremany per exemple?
Click to expand...
Click to collapse
Yes you can.Only the modem version might be different so you might have to change that if you you experience slow data speeds and weak signal.But France has ND3 modem which i am using in India and no issues with network or data speeds so you should be okay too.
singhpratik87 said:
Yes you can.Only the modem version might be different so you might have to change that if you you experience slow data speeds and weak signal.But France has ND3 modem which i am using in India and no issues with network or data speeds so you should be okay too.
Click to expand...
Click to collapse
It did work, dont know why but now i could install any 4.4.2 ROMs :laugh:
U guys did a great job helping me out here, i really appreciate it, many thanks :good:
hey can anyone help me? i've recently reverted my note 2 back to stock via odin and everything seemed fine. When the phone booted and i went through the setup process it always hangs. No matter what i do it always hangs. I've tried reflashing it and rebooting it over and over again but it always hangs. anyone know why this keeps happening?
Are you flashing the latest stock ROM? You're performing a factory reset before booting the ROM for the first time?
audit13 said:
Are you flashing the latest stock ROM? You're performing a factory reset before booting the ROM for the first time?
Click to expand...
Click to collapse
Yup latest stock rom, and before i flashed via odin i deleted my previous rom via twrp and formatted internal storage so its 100% clean
I've downgraded a Note 2 sgh-i317m to 4.1.1 from 4.4.2 by flashing a stock 4.1.1 ROM from sammobile.com in order to network unlock the phone. Flashing the stock 4.1.1 ROM tripped knox and could be installed via Odin because the 4.1.1 ROM from sammobile.com did not contain a 4.1.1 bootloader so I wound up with a stock 4.1.1 ROM on a 4.4.2 bootloader. After unlocking, I flashed the stock 4.4.2 ROM again and the the phone worked as it should.
I'm not sure which phone you have and I'm not sure downgrading and upgrading will work in your case but it's something you may want to look into.
audit13 said:
I've downgraded a Note 2 sgh-i317m to 4.1.1 from 4.4.2 by flashing a stock 4.1.1 ROM from sammobile.com in order to network unlock the phone. Flashing the stock 4.1.1 ROM tripped knox and could be installed via Odin because the 4.1.1 ROM from sammobile.com did not contain a 4.1.1 bootloader so I wound up with a stock 4.1.1 ROM on a 4.4.2 bootloader. After unlocking, I flashed the stock 4.4.2 ROM again and the the phone worked as it should.
I'm not sure which phone you have and I'm not sure downgrading and upgrading will work in your case but it's something you may want to look into.
Click to expand...
Click to collapse
I've managed to get the phone working (N7100) and it seems to run fine on Nougat. I did some testing and indeed it would always crash on setup with kitkat roms. I wonder why this is the case....
It is strange that kit kat causes a problem.
Have you tried using a different version of twrp to wipe the system before flashing with Odin? Can't think of anything else that may solve the problem.