Related
I'm having issues with a bootloop on the incredible after rooting using unrevoked 3 and making the mistake of choosing cyanogenmod as the recovery because I'm incredibly new at this. Now granted this isn't an issue, I have root access now and I'm able to assign superuser and the phone boots to what looks like the stock rom. However, I wanted to flash cyanogen 7 rc2 and it's giving me a lot of issues when I try to access the clockworkmod recovery screen. I downloaded the rommanager from the market and flashed the recovery to clockworkmod 3.0.0.8 as per a wiki online and tried to boot to recovery. from there it hits the HTC incredible screen, then flashes every 3 seconds rather than showing the green text it's supposed to show.
I still have S-on and unrevoked won't run properly again. Tried running the factory reset and it's another bootloop. I tried going through the steps for a "manual recovery file flash via cyanogen's wiki, but I'm running into errors.
Summary:
unrevoked 3.32 completed successfully even using the cyanogenmod rom as the recovery file.
Have root access, S-on, radio version ~.7.28
Can't flash back to stock due to bootloop
Can't factory reset due to bootloop
Can't get to clockworkmod recovery screen due to bootloop
phone able to boot to main screen with original
Ideal solution: get to clockworkmod recovery screen and install C7RC2
Any help appreciated!
Why do you think using ClockworkMod was a mistake? It's one of the better AOSP ROMs out there.
It sounds to me like you're probably going to have to download one of the stock RUUs to completely revert your phone to stock. You might have a corrupted recovery. You can't flash ClockworkMod or an alternative recovery via RomManager?
oh don't get me wrong, my huge problem here is that I can't get into recovery, and I didn't load clockworkmod initally, but it is (as rom manager says) my recovery image and it's just not working at all.
I tried going with a RUU and it wouldn't get into bootloader properly (just shows HTC on the screen till the the ruu times out) I'll try on a 32 bit machine when I get home. I was originally able to flash on that and unrevoked was giving me issues till I did a 32 bit xp attempt. Thanks for the response!
whoops, forgot to address your last point. Tried another version of clockwork and the RA_GNM 1.8.1 and neither stopped it from bootlooping rather than recovery screen.
HTCP2newb said:
I'm having issues with a bootloop on the incredible after rooting using unrevoked 3 and making the mistake of choosing cyanogenmod as the recovery because I'm incredibly new at this. Now granted this isn't an issue, I have root access now and I'm able to assign superuser and the phone boots to what looks like the stock rom. However, I wanted to flash cyanogen 7 rc2 and it's giving me a lot of issues when I try to access the clockworkmod recovery screen. I downloaded the rommanager from the market and flashed the recovery to clockworkmod 3.0.0.8 as per a wiki online and tried to boot to recovery. from there it hits the HTC incredible screen, then flashes every 3 seconds rather than showing the green text it's supposed to show.
I still have S-on and unrevoked won't run properly again. Tried running the factory reset and it's another bootloop. I tried going through the steps for a "manual recovery file flash via cyanogen's wiki, but I'm running into errors.
Summary:
unrevoked 3.32 completed successfully even using the cyanogenmod rom as the recovery file.
Have root access, S-on, radio version ~.7.28
Can't flash back to stock due to bootloop
Can't factory reset due to bootloop
Can't get to clockworkmod recovery screen due to bootloop
phone able to boot to main screen with original
Ideal solution: get to clockworkmod recovery screen and install C7RC2
Any help appreciated!
Click to expand...
Click to collapse
Did you try getting to recovery manually power off the phone while its off press power and volume down at the same time you should be in hboot use the volume button to scroll down boot into recovery.....
Sent from my Incredible using XDA App
I don't think unrevoked finish all The way because you should be s-off did you wait until it said "done"..... or did you stop when it said "this is a triumph"
Sent from my Incredible using XDA App
Okay, from a 32 bit system has resolved the flashing back to a stock rom, I will update as to whether I can get into recovery and will wait until I am told "triumphant" this time around.
Will post an update in a bit if this was all that was necessary to fix the issue. Thank you all to have posted so far, please post if you think I'm missing something else.
HTCP2newb said:
Okay, from a 32 bit system has resolved the flashing back to a stock rom, I will update as to whether I can get into recovery and will wait until I am told "triumphant" this time around.
Will post an update in a bit if this was all that was necessary to fix the issue. Thank you all to have posted so far, please post if you think I'm missing something else.
Click to expand...
Click to collapse
No you need to wait till it says done sorry you misunderstood me......let it go till it says done and it stops completely..... because the last thing it does is flash the recovery
Sent from my Incredible using XDA App
Did you try flashing a recovery through hboot?
Sent from my ADR6300 using XDA App
Okay, problem totally resolved. basically what happened was that there was an incomplete unrevoked process for whatever reason or another. I repaired by downloading the RUU off the HTC website and flashing back to stock. That generated an error of "your firmware is too new" which is available elsewhere in XDA, basically solved by going into hboot and factory resetting.
Once I had the factory reset completed, I used a 32 bit system to unrevoke the phone (after setting debugging to on in applications > developer settings >debugging on) then I was able to properly boot into recovery. I recommend Clockworkmod update to 3.0.0.8 in Rom manager, but I used 2.5 and didn't have much of an issue. I backed up and the wiped the memory and cache and installed 7r2 without an issue.
The phone is WAY more stable now (thanks to all the hard work at Cyanogen! Thank you also to everyone who posted here!) Pandora doesn't randomly cut songs in half and battery life seems to have improved. Whether that was verizon's crap or I went market-crazy and had waaaay too many apps syncing... I can't say.
Thank you everyone again!
I accidentally flashed the kernel for my old SGS II International to my Epic 4G Touch, but I managed to get it back to stock eventually. Everything was fine for the past couple months, and today I finally decided to install the system update(which I just put off for awhile despite all the prompts). Then it gave me that white triangle and when I rebooted into recovery mode. Now it just stays in recovery mode no matter what I do. Reboot option? Reboots back into recovery? Factory reset option? Boots back into recovery.
The ok button should be the power button right? This is a bit different from my old SGS
i would try pulling the battery and attempting to boot into download
yea, try & get into download mode... power off>vol dn+power until download mode is on the screen. then use ODIN/HEIMDALL to flash a stock tar file.
I should have mentioned that I did remove the battery and leave it out for a few minutes several times. It just kept booting back into recovery. I did eventually find the jig I made which was able to force it into download mode. But heimdall just keeps giving me this "ERROR: Claiming interface failed!" message even though it can detect the phone.
So no one has any idea what to do about this?
Did you try odin? If that fails put a rom(.zip) in sd card and flash from revovery.
Edit: if you are goin to switch from heimdall to odin you have to unistall heimdalls drivers. There are instructions on how to do this in heimdalls readme file.
javi_emma said:
Did you try odin? If that fails put a rom(.zip) in sd card and flash from revovery.
Edit: if you are goin to switch from heimdall to odin you have to unistall heimdalls drivers. There are instructions on how to do this in heimdalls readme file.
Click to expand...
Click to collapse
No, I didn't try Odin because I'm using OS X. I guess I'm going to have to make a windows boot partition. sigh
Well I guess I'll try to flash a rom from recovery first.
Well this is odd. It won't let me write anything to the sd card I normally use in it. It says it's read only. But uh....it always copied things fine if it was IN either this phone or my SGS II International when I tried to copy things.
I should just be able to put the rom on any micro SD card right? I have another 4 GB laying around here I can use if so.
Correct any sd should work!
Sent from my SPH-D710 using Tapatalk
And once again I highlight "apply update from sdcard" and hit the power button...just reboots into recovery mode for the millionth time without doing anything.
Gradius said:
And once again I highlight "apply update from sdcard" and hit the power button...just reboots into recovery mode for the millionth time without doing anything.
Click to expand...
Click to collapse
You may have to go the route of installing Odin and flashing a full stock tar that includes ROM, kernel, and modem so it overwrites everything in that one flash. I don't think it is something you can do by flashing in a recovery
Sent from my Nexus S 4G using xda premium
Gradius said:
And once again I highlight "apply update from sdcard" and hit the power button...just reboots into recovery mode for the millionth time without doing anything.
Click to expand...
Click to collapse
You have the stock recovery. That why. U can't flash an unsigned from from there. You are gonna have to Odin something. Either a full tar or maybe a kernel with cwm to flash something.
Sent from my Nexus S 4G using xda premium
Well anyone want to recommend/link me a tar? I'm making a windows partition right now so I can run Odin.
And yeah I figured it was because I put it back to stock that it wasn't working. But if it's back on stock why am I still getting the white triangle with the orange exclamation?
In fact if it's back to stock the past couple months and been working fine then why did it decide to screw up when I tried to install the OS update?
Gradius said:
In fact if it's back to stock the past couple months and been working fine then why did it decide to screw up when I tried to install the OS update?
Click to expand...
Click to collapse
The OTA updates are not always perfect. It is possible that there was something lingering from before. Let me try to find a link to a one click stock restore for you ...
Sent from my SPH-D710 using xda premium
Here is sfhub's EL29 full stock Gingerbread restore ...
http://forum.xda-developers.com/showthread.php?t=1433101
Sent from my SPH-D710 using xda premium
Haha, double post, haha
Sent from my SPH-D710 using Tapatalk
Hey guys I'm new to the forum so please tolerate my lack of knowledge. I've already flashed a few s3's with roms, so I'm familiar with process. I bought another s3, installed cwm recovery with odin, and then went into recovery and flashed su. Rebooted and made sure it was rooted.
I then did something different, which was updated to newer cwm recovery using rom manager. I rebooted into recovery using rom manager. I went through all steps and flashed darthstalker v3 (I've already flashed this on other s3's successfully many times). I rebooted system, but instead of booting into rom it keeps booting back into recovery (cwm, not android recovery). I can get into download mode and flash stock rom with odin. I tried repeating process and used twrp instead of cwm, but still can't boot into rom. It keeps rebooting into recovery (cwm or twrp). Any suggestions? Thanks in advance!
Sent from my SGH-T999 using Tapatalk 2
Does it do it with only that rom?
Sent from my SGH-T999
Have you tried clearing cache/davlik/data?
elmatador1973 said:
Hey guys I'm new to the forum so please tolerate my lack of knowledge. I've already flashed a few s3's with roms, so I'm familiar with process. I bought another s3, installed cwm recovery with odin, and then went into recovery and flashed su. Rebooted and made sure it was rooted.
I then did something different, which was updated to newer cwm recovery using rom manager. I rebooted into recovery using rom manager. I went through all steps and flashed darthstalker v3 (I've already flashed this on other s3's successfully many times). I rebooted system, but instead of booting into rom it keeps booting back into recovery (cwm, not android recovery). I can get into download mode and flash stock rom with odin. I tried repeating process and used twrp instead of cwm, but still can't boot into rom. It keeps rebooting into recovery (cwm or twrp). Any suggestions? Thanks in advance!
Sent from my SGH-T999 using Tapatalk 2
Click to expand...
Click to collapse
Try completely wiping your phone then PC Odin using root66 in download mode. Afterwards, let the phone sit for 15 minutes. Reboot the phone then download and install GooManager from the Play Store. Open the application and press the menu button to access the options. Press 'install openrecovery' and go through the installation process. You should now have no issue with your device.
Sent from my SGH-T999 using xda app-developers app
chrisram88 said:
Does it do it with only that rom?
Sent from my SGH-T999
Click to expand...
Click to collapse
I haven't tried it with a different rom, but I've repeated this process with different roms on several s3's. Only thing I did different was install cwm from rom manager. Thnx
se1000 said:
Have you tried clearing cache/davlik/data?
Click to expand...
Click to collapse
Yes, before and after rom installation. Problem remains.
Noobiologist said:
Try completely wiping your phone then PC Odin using root66 in download mode. Afterwards, let the phone sit for 15 minutes. Reboot the phone then download and install GooManager from the Play Store. Open the application and press the menu button to access the options. Press 'install openrecovery' and go through the installation process. You should now have no issue with your device.
Sent from my SGH-T999 using xda app-developers app
Click to expand...
Click to collapse
Will try that tomorrow. I got hasty and hardbricked it ((. Foolishly flashed exitrecovery.zip, not realizing it was only for LG! Getting it unbricked tomorrow, and will try your suggestion. Thnx.
I have a rooted Galaxy S3 that is running the ATT Jelly Bean update.
Last night, while looking at ROM manager I got a popup saying there is a newer version of CWM and did I want to install it.
After installing it, the phone will only boot into recovery. I cannot get it to start. And when I tried to restore from a backup that I have used successfully before, I got an error while restoring data.
At this point, I am thinking that I might have bricked this phone. Searching on the ATT Galaxy S3 forum hasn't turned up anything relevant.
Does anyone have an idea what I can try next?
Thanks
northstar7 said:
I have a rooted Galaxy S3 that is running the ATT Jelly Bean update.
Last night, while looking at ROM manager I got a popup saying there is a newer version of CWM and did I want to install it.
After installing it, the phone will only boot into recovery. I cannot get it to start. And when I tried to restore from a backup that I have used successfully before, I got an error while restoring data.
At this point, I am thinking that I might have bricked this phone. Searching on the ATT Galaxy S3 forum hasn't turned up anything relevant.
Does anyone have an idea what I can try next?
Thanks
Click to expand...
Click to collapse
If you a can boot into recovery than you aren't bricked.
You can do a factory reset that might clear it up.
Worst case go into download mode and use Odin to reinstall the stock ROM.
Sent from my SGH-I747 using xda app-developers app
northstar7 said:
I have a rooted Galaxy S3 that is running the ATT Jelly Bean update.
Last night, while looking at ROM manager I got a popup saying there is a newer version of CWM and did I want to install it.
After installing it, the phone will only boot into recovery. I cannot get it to start. And when I tried to restore from a backup that I have used successfully before, I got an error while restoring data.
At this point, I am thinking that I might have bricked this phone. Searching on the ATT Galaxy S3 forum hasn't turned up anything relevant.
Does anyone have an idea what I can try next?
Thanks
Click to expand...
Click to collapse
Im assuming you powered down, did a battery pull and powered back up? Factory reset?
What error message is displayed when trying to restore a backup?
The latest cwm release is 6.0.2.8. If you came from 6.0.2.3, I would download a cwm flashable zip of that recovery and flash that. Perhaps try a reboot then. If it's still a no-go, try restoring a backup with the cwm you had just downloaded and flashed to see if it will restore without an error message
Different CWM
xBeerdroiDx said:
Im assuming you powered down, did a battery pull and powered back up? Factory reset?
What error message is displayed when trying to restore a backup?
The latest cwm release is 6.0.2.8. If you came from 6.0.2.3, I would download a cwm flashable zip of that recovery and flash that. Perhaps try a reboot then. If it's still a no-go, try restoring a backup with the cwm you had just downloaded and flashed to see if it will restore without an error message
Click to expand...
Click to collapse
Thanks very much for the advice.
For the record, my phone is displaying "ClockworkMod Recovery v6.0.2.9"
I just has this happen to me as well. I just put the s3 in download mode and used Odin to re flash cwm. I'm using the same version cwm.
Sent from my SAMSUNG-SGH-I747 using xda premium
I as well. Tried everything and no go. Will try ODIN and see if it works.
Domoo said:
I just has this happen to me as well. I just put the s3 in download mode and used Odin to re flash cwm. I'm using the same version cwm.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
stranglely pressing the recovery button combo fixed it and im back in CM10.1 #lolwut?
In the end I got the phone working again
For whatever reason, after getting that update to ClockworkMod, the phone would not boot.
I followed the Beginners' Guide to Rooting the Galaxy S3 forum. When I was finished I immediately got an OTA update from ATT.
So now the phone is running again, but I've lost most of my customization and personal data.
What is with this CWM "upgrade?" Or is the problem with ROM Manager?
More likely is that I did something wrong.
At least I can make calls now.
Same here, stay away from that update! Bad things!
This also happened to me. Cwm is showing up as .9 instead of .8. I flashed a previous version of twrp and it still proceeded to go into recovery mode after selecting reboot. I did a factory reset and re flashed aokp and also cm10.1 (along with gapps of course) and it still did it. So I pulled the battery and put it into download mode and reset it from there. That's the only way to get the phone to boot up. From what I see here, is the basic fix for this problem flashing an older cwm in Odin?
Having the same issue, version .9 No amount of clearing data/wipe/reflash/restore will do anything for me either. So much for a lunchtime AOKP update...
I've looked in several different forums on xda and the general fix seems to be flashing a previous version of cwm. No need to reset your phone and flash roms all day long.
Download prior cwm release (.tar)
pull battery and replace
boot to download mode
connect to pc and flash cwm
Disconnect, pull battery, reboot
Here's the 6.0.2.3 release. You can grab the .8 in the Android dev section if you wish
https://www.dropbox.com/s/sfkjtndn7k0urmh/recovery-clockwork-6.0.2.3-d2att.tar
Let me know if this does not work. If your device is not recognized by your pc, you can try flashing this cwm zip in recovery itself (if you have a micro sd card):
http://d-h.st/8qP
I flashed with the same version of cwm I had previously before this issue (6.0.28). It seems to be an issue with 6.0.29 if so many people have this same issue.
Sent from my SAMSUNG-SGH-I747 using xda premium
xBeerdroiDx said:
I've looked in several different forums on xda and the general fix seems to be flashing a previous version of cwm. No need to reset your phone and flash roms all day long.
Download prior cwm release (.tar)
pull battery and replace
boot to download mode
connect to pc and flash cwm
Disconnect, pull battery, reboot
Here's the 6.0.2.3 release. You can grab the .8 in the Android dev section if you wish
https://www.dropbox.com/s/sfkjtndn7k0urmh/recovery-clockwork-6.0.2.3-d2att.tar
Let me know if this does not work. If your device is not recognized by your pc, you can try flashing this cwm zip in recovery itself (if you have a micro sd card):
http://d-h.st/8qP
Click to expand...
Click to collapse
I flashed the CMW-recovery_ATT-6.0.2.3_zip directly from the external sd card to the phone and the phone is now working. but I did have to reboot phone twice. the first time it stayed in recovery.
THANK YOU!!
xBeerdroiDx said:
I've looked in several different forums on xda and the general fix seems to be flashing a previous version of cwm. No need to reset your phone and flash roms all day long.
Download prior cwm release (.tar)
pull battery and replace
boot to download mode
connect to pc and flash cwm
Disconnect, pull battery, reboot
Here's the 6.0.2.3 release. You can grab the .8 in the Android dev section if you wish
https://www.dropbox.com/s/sfkjtndn7k0urmh/recovery-clockwork-6.0.2.3-d2att.tar
Let me know if this does not work. If your device is not recognized by your pc, you can try flashing this cwm zip in recovery itself (if you have a micro sd card):
http://d-h.st/8qP
Click to expand...
Click to collapse
I believe this can even be simplified a bit more. At least for me, some people may find Odin to be the simple way to do things. So you're stuck at recovery:
Hold the power button for 10 seconds to power off.
Boot to download mode by holding volume down and home. The phone will probably start to boot right away after releasing the power button. If it doesn't go to download, then your timing is off, try again.
Hold the power button for 10 seconds to power off and reboot.
It should boot regularly now.
Flash a new recovery. You can download CWM 6.0.2.8 or use this as an opportunity to move to TWRP. Once you have the img file on your phone, go to a terminal and (after su, if needed) run dd if=/sdcard/recovery.img of=/dev/block/mmcblk0p18 (replace "/sdcard/recovery.img" with the path and name of the img file you downloaded. You can also flash the recovery using whatever other on-phone method you prefer.
The CWM download page is now showing that 6.0.2.8 is the newest version for many of the S3 variants, so they've certainly noticed the bug.
J M L said:
I believe this can even be simplified a bit more. At least for me, some people may find Odin to be the simple way to do things. So you're stuck at recovery:
Hold the power button for 10 seconds to power off.
Boot to download mode by holding volume down and home. The phone will probably start to boot right away after releasing the power button. If it doesn't go to download, then your timing is off, try again.
Hold the power button for 10 seconds to power off and reboot.
It should boot regularly now.
Flash a new recovery. You can download CWM 6.0.2.8 or use this as an opportunity to move to TWRP. Once you have the img file on your phone, go to a terminal and (after su, if needed) run dd if=/sdcard/recovery.img of=/dev/block/mmcblk0p18 (replace "/sdcard/recovery.img" with the path and name of the img file you downloaded. You can also flash the recovery using whatever other on-phone method you prefer.
The CWM download page is now showing that 6.0.2.8 is the newest version for many of the S3 variants, so they've certainly noticed the bug.
Click to expand...
Click to collapse
How is this simpler? There are left out bits and errors all through your instructions. My steps were for odin so I'm not sure why you thought they were not.
Hello all,
Quick background - my wife's T-Mobile S4 went kaput on our honeymoon last night, but I was at least able to save some of her data. The problem now goes to installing a new ROM on her device.
I have wiped EVERYTHING and formatted the data, but when I install ANY ROM (I've tried multiple), I always get the E: Unable to mount '/data" error. Normally, I would just ODIN the stock tar, then install a custom recovery again and then the ROM, but I only have my work computer for the rest of my honeymoon and I don't have administrative access to run ODIN (you might not think it requires it, but if you're only a standard user then you cannot bypass UAC to run it).
Does anyone have any ideas on how to get this to mount? The phone will not boot past the "Samsung Galaxy S4" screen. I've tried going into TWRP and mounting Data but it will not work.
Any help is greatly appreciated! Please keep in mind that I don't have access to ODIN!
- Taxmaster
Taxmaster said:
Hello all,
Quick background - my wife's T-Mobile S4 went kaput on our honeymoon last night, but I was at least able to save some of her data. The problem now goes to installing a new ROM on her device.
I have wiped EVERYTHING and formatted the data, but when I install ANY ROM (I've tried multiple), I always get the E: Unable to mount '/data" error. Normally, I would just ODIN the stock tar, then install a custom recovery again and then the ROM, but I only have my work computer for the rest of my honeymoon and I don't have administrative access to run ODIN (you might not think it requires it, but if you're only a standard user then you cannot bypass UAC to run it).
Does anyone have any ideas on how to get this to mount? The phone will not boot past the "Samsung Galaxy S4" screen. I've tried going into TWRP and mounting Data but it will not work.
Any help is greatly appreciated! Please keep in mind that I don't have access to ODIN!
- Taxmaster
Click to expand...
Click to collapse
Sounds like a twrp issue. Try grabbing the cwm flash able zip and adb push to the sd card and then use twrp to install it. I've read so many issues about twrp. I recommend staying away from it. Philz touch recovery is really awesome too.
Sent from my SGH-M919 using Tapatalk 2
elesbb said:
Sounds like a twrp issue. Try grabbing the cwm flash able zip and adb push to the sd card and then use twrp to install it. I've read so many issues about twrp. I recommend staying away from it. Philz touch recovery is really awesome too.
Sent from my SGH-M919 using Tapatalk 2
Click to expand...
Click to collapse
Hello! I actually downloaded Philz touch recovery in both .zip and in .md5, so that is what I intend to go with. The issue is how I push it using adb, as I believe I need to install something in order to do so, but I don't have any administrative privileges! This is what's preventing me from running ODIN in the first place!
Can you confirm that I can push using adb without installing anything?
Thank you! - Taxmaster
I had this issue. Odin flashing and then booting into "STOCK RECOVERY" after flashing and then a factory reset in the stock recovery followed by a fresh re-flash from Odin worked to get my phone back up and running again.
I don't know how you are going to be able to fix it by just flashing a recovery. I tried for hours and could not get it to boot from just recovery alone.
Monkz said:
I had this issue. Odin flashing and then booting into "STOCK RECOVERY" after flashing and then a factory reset in the stock recovery followed by a fresh re-flash from Odin worked to get my phone back up and running again.
I don't know how you are going to be able to fix it by just flashing a recovery. I tried for hours and could not get it to boot from just recovery alone.
Click to expand...
Click to collapse
What you noted would be my plan if I had admin rights to my computer, but since I cannot get ODIN, I'm screwed at the moment. I'm hoping someone can assist with the "adb" proposal, however I'm not sure one can download/run adb without installation or prompt from UAC
Taxmaster said:
What you noted would be my plan if I had admin rights to my computer, but since I cannot get ODIN, I'm screwed at the moment. I'm hoping someone can assist with the "adb" proposal, however I'm not sure one can download/run adb without installation or prompt from UAC
Click to expand...
Click to collapse
I don't believe admin is required for adb... You could always try it... worst thing that could happen would be nothing.
lordcheeto03 said:
I don't believe admin is required for adb... You could always try it... worst thing that could happen would be nothing.
Click to expand...
Click to collapse
Using ADB does not require admin privelages, however, if your computer does not have the necessary drivers to detect the device in recovery, then you will have to install the drivers, which then yes UAC is required. HOWEVER, if you have another phone or device that supports MicroSD cards, you can just pop in the MicroSD into a working device and transfer the zip that way, then transfer back the sd card and flash
elesbb said:
Using ADB does not require admin privelages, however, if your computer does not have the necessary drivers to detect the device in recovery, then you will have to install the drivers, which then yes UAC is required. HOWEVER, if you have another phone or device that supports MicroSD cards, you can just pop in the MicroSD into a working device and transfer the zip that way, then transfer back the sd card and flash
Click to expand...
Click to collapse
I did exactly what's noted above --> took out the SDcard, put it in another phone, transferred over the .zip, put it back in her phone, went to TWRP, wiped everything on the device, installed the .zip, and rebooted into recovery from TWRP, and then the new recovery booted! I did another wipe/factory reset and then installed a ROM, but when I hit reboot, it didn't reboot past the Samsung Galaxy S4 splash screen , and to make matters worse, when I go to enter recovery pressing home+up+power, it says "Recovery Booting ...." in the top left corner but it won't boot into recovery!!!
Thoughts?
If someone could strip administrative privileges off of a version of ODIN v3 for me, that would be great! I don't see how else to get around this now!
-Taxmaster
Taxmaster said:
I did exactly what's noted above --> took out the SDcard, put it in another phone, transferred over the .zip, put it back in her phone, went to TWRP, wiped everything on the device, installed the .zip, and rebooted into recovery from TWRP, and then the new recovery booted! I did another wipe/factory reset and then installed a ROM, but when I hit reboot, it didn't reboot past the Samsung Galaxy S4 splash screen , and to make matters worse, when I go to enter recovery pressing home+up+power, it says "Recovery Booting ...." in the top left corner but it won't boot into recovery!!!
Thoughts?
If someone could strip administrative privileges off of a version of ODIN v3 for me, that would be great! I don't see how else to get around this now!
-Taxmaster
Click to expand...
Click to collapse
Out of curiosity, are you flashing a ROM for the T-Mobile S4? If no, are you using a T-Mobile kernel? I only ask because a kernel for a different device will normally cause you to not be able to pass the initial Galaxy S4 screen... Also, as far as TWRP goes, sometimes it doesn't go right into recovery. If it fails to enter recovery after a reasonable amount of time, just hold power to turn it off and try again. I've had to do it 2-3 times at least just to successfully enter TWRP.
lordcheeto03 said:
Out of curiosity, are you flashing a ROM for the T-Mobile S4? If no, are you using a T-Mobile kernel? I only ask because a kernel for a different device will normally cause you to not be able to pass the initial Galaxy S4 screen... Also, as far as TWRP goes, sometimes it doesn't go right into recovery. If it fails to enter recovery after a reasonable amount of time, just hold power to turn it off and try again. I've had to do it 2-3 times at least just to successfully enter TWRP.
Click to expand...
Click to collapse
I am installing a T-Mobile S4 ROM that uses a custom kernel. The ROM before was the same ROM just a lower revision, same kernel.
With respect to TWRP, I thought it was all gone now that I installed the CWM touch version. I've tried doing it a million times and cannot get back into either TWRP or CWM. At this point, the only thing I can do is turn on the device to see the "Samsung Galaxy S4" screen, attempt booting into recovery but never make it past the screen saying "Recovery Booting", or enter Download Mode but I cannot use it since I can't run ODIN on my work laptop .... stupid admin privileges!
Taxmaster said:
I am installing a T-Mobile S4 ROM that uses a custom kernel. The ROM before was the same ROM just a lower revision, same kernel.
With respect to TWRP, I thought it was all gone now that I installed the CWM touch version. I've tried doing it a million times and cannot get back into either TWRP or CWM. At this point, the only thing I can do is turn on the device to see the "Samsung Galaxy S4" screen, attempt booting into recovery but never make it past the screen saying "Recovery Booting", or enter Download Mode but I cannot use it since I can't run ODIN on my work laptop .... stupid admin privileges!
Click to expand...
Click to collapse
Not sure what happened there.. very strange. But seems as if you have no recovery xD lol Maybe heimdall will work. Never used it not sure if it needs UAC to work. But dont use TWRP anymore
As far as your situation goes, maybe if you have the time and fast enough internet, see if you can download a linux distro (i recommend fedora as it is small and light) then make a bootable USB from that distro (if you have a flash drive) then use Heimdall in linux to flash the tar image.
Or just wait to get home. not sure how long your honeymoon is xD
elesbb said:
Not sure what happened there.. very strange. But seems as if you have no recovery xD lol Maybe heimdall will work. Never used it not sure if it needs UAC to work. But dont use TWRP anymore
As far as your situation goes, maybe if you have the time and fast enough internet, see if you can download a linux distro (i recommend fedora as it is small and light) then make a bootable USB from that distro (if you have a flash drive) then use Heimdall in linux to flash the tar image.
Or just wait to get home. not sure how long your honeymoon is xD
Click to expand...
Click to collapse
I think I just need to accept that fact that I have been had and that the only thing I can do is wait until I'm home to use ODIN. Absolutely asinine in my opinion, however it seems the only logical conclusion at this point.
If anyone else cares to chime in with suggestions, please let me know!
-Taxmaster
I have had the same problem several times. The only way I have been able to boot up is to completely format data and either restore from backup or reflash a new ROM. If I wipe the dalvik cache after doing so however, it will not boot (hangs at the galaxy s4 screen like you said) and I will have to reflash or restore a 2nd time. (I'm using twrp too, but will switch to cwm if this happens again)
I m curious. Have you run into this problem again? Seems like every time my phone shuts off and tries to boot I have to restore from a backup that is days or weeks old. Super annoying. The first time this happened I restored to stock from Odin and did not use any backups in the hope that it would solve my problem and prevent it from happening again. No such luck.
coolastar said:
I have had the same problem several times. The only way I have been able to boot up is to completely format data and either restore from backup or reflash a new ROM. If I wipe the dalvik cache after doing so however, it will not boot (hangs at the galaxy s4 screen like you said) and I will have to reflash or restore a 2nd time. (I'm using twrp too, but will switch to cwm if this happens again)
I m curious. Have you run into this problem again? Seems like every time my phone shuts off and tries to boot I have to restore from a backup that is days or weeks old. Super annoying. The first time this happened I restored to stock from Odin and did not use any backups in the hope that it would solve my problem and prevent it from happening again. No such luck.
Click to expand...
Click to collapse
I ended up having to wait until I got home to use ODIN. I ODIN'd up the stock .tar and then installed Philz touch recovery (CWM-based), then I did a full wipe of everything and installed a ROM. Problem solved.
With that noted, I abandoned TWRP and am now only using CWM on my wife's phone.
Taxmaster said:
I ended up having to wait until I got home to use ODIN. I ODIN'd up the stock .tar and then installed Philz touch recovery (CWM-based), then I did a full wipe of everything and installed a ROM. Problem solved.
With that noted, I abandoned TWRP and am now only using CWM on my wife's phone.
Click to expand...
Click to collapse
Same, TWRP just has too many problems.
CWM is much more reliable.
Sent from my SGH-M919 using xda premium
Taxmaster said:
I ended up having to wait until I got home to use ODIN. I ODIN'd up the stock .tar and then installed Philz touch recovery (CWM-based), then I did a full wipe of everything and installed a ROM. Problem solved.
With that noted, I abandoned TWRP and am now only using CWM on my wife's phone.
Click to expand...
Click to collapse
If you were using TWRP 2.6.0, that could have been the problem. I reverted back to 2.5.0.2 and like many others, have had no issues. If you had a TWRP backup, that might have fixed it early on.