[Q] Can not write to gnex NAND at all. - Samsung Galaxy Nexus

I'm trying to wipe and restore an unlocked maguro Galaxy Nexus. No custom recovery, no root, stock ROM. But I can't wipe it at all. Recovery Mode factory reset doesn't work, it just reboots, and boots up as if it wasn't wiped at all. fastboot doesn't work, it gives the error 'remote: Wipe Failed'
Code:
fastboot -w
erasing 'userdata'...
OKAY [ 0.007s]
formatting 'userdata' partition...
Creating filesystem with parameters:
Size: 15961423872
Block size: 4096
Blocks per group: 32768
Inodes per group: 8192
Inode size: 256
Journal blocks: 32768
Label:
Blocks: 3896832
Block groups: 119
Reserved block group size: 951
Created filesystem with 11/974848 inodes and 103467/3896832 blocks
sending 'userdata' (137971 KB)...
writing 'userdata'...
FAILED (remote: Write Fail)
finished. total time: 264.655s
Even ODIN won't wipe, it fails with and without NAND Erase All. Not even ODIN can wipe the thing.
Without erasing NAND
Code:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> odin.takju.jwr66y.4.3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> bootloader.img
<ID:0/003> radio.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003> Complete(Write) operation failed.
Erasing NAND
Code:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> odin.takju.jwr66y.4.3.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Erase...
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
I'm starting to think that it's a hardware problem with the NAND itself. I've been looking all over the web and I can't find anyone who has the same problems as I. Where should I go from here?

Lock your bootloader if its still unlocked after doing that your nand is fried.
Sent from my Nexus 10 using XDA Free mobile app

mrgnex said:
Lock your bootloader if its still unlocked after doing that your nand is fried.
Sent from my Nexus 10 using XDA Free mobile app
Click to expand...
Click to collapse
Once its unlocked and it reboots, it relocks

blabdude said:
Once its unlocked and it reboots, it relocks
Click to expand...
Click to collapse
Your nand has been fried. Sucks man..
Sent from my Galaxy Nexus using XDA Free mobile app

Related

E:failed to mount tried uroot and unbricking didnt work fail

yesterday I wrote to find a solution to E failed to mount/system invalid argument cant mount system I was reffered to wwjosdew video and also went onto viperboy thread on how to unbrick phones I did everything shown in the video and what viperboy said but when odin was running the file it failed and gave me this
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> SPH-L900_L900VPALJ1_L900VPALJ1_L900SPTALJ1.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> cache.img
<ID:0/003> hidden.img
<ID:0/003> modem.bin
<ID:0/003> param.bin
<ID:0/003> recovery.img
<ID:0/003> sboot.bin
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
can anynone help me out with this problem been working on this for hours I have wiped and reset the phone already and I also downloaded the toolkit and the kit recognizes my phone and serial is rcognized.........
S boot is going to fail when loading a Older tar ....it won't allow you to go back to a older boot loader ... use this and next time search it has been ask plenty of timeshttp://forum.xda-developers.com/showthread.php?t=2086769
Sent from my SPH-L900 using Xparent BlueTapatalk 2

[Q] Stuck in bootloop after flashing Android_Revolution_HD-Note2_20.1

Hi,
A brief background...I downloaded and flashed Android_Revolution_HD-Note2_20.1 successfully...
After completing all the things I was checking SU and tried updating it when it asked me i choose TWRP/CWM and the phone restart with bootloop... and can't enter recovery...
What should I do now...I am stuck badly!!! Please help
Thanks in advance
Cheers
additional info
I tried to flash stock rom and it failed
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100DDUEML4_N7100ODDEML2_N7100DDEMK1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> tz.img
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> system.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Please help!!!

[Q] [Help] NAND Write Start!!

I was on T889UVALL4, use Odin to flash root66_TMO_T889UVUCMK7_2.tar.md5, got PASS, phone stuck in boot loop, can not get into recovery mode, so I try flashing again and got the following error. ( i flash KIES_HOME_T889UVALL4_T889TMBALL4_598701_REV04_user _low_ship.tar.md5 with the same result)
Please help.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
here is the Odin log for stock firmware:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_T889UVALL4_T889TMBALL4_598701_REV04_user _low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My question is: Can this be fix with Odin? or do I need to fix a shop that can repair the EMMC? if it is the latter, does anyone know where to find a trust worthy shop with in the San Francisco bay area?
Thanks
onqq said:
I was on T889UVALL4, use Odin to flash root66_TMO_T889UVUCMK7_2.tar.md5, got PASS, phone stuck in boot loop, can not get into recovery mode, so I try flashing again and got the following error. ( i flash KIES_HOME_T889UVALL4_T889TMBALL4_598701_REV04_user _low_ship.tar.md5 with the same result)
Please help.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> root66_TMO_T889UVUCMK7_2.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
here is the Odin log for stock firmware:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> KIES_HOME_T889UVALL4_T889TMBALL4_598701_REV04_user _low_ship.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
My question is: Can this be fix with Odin? or do I need to fix a shop that can repair the EMMC? if it is the latter, does anyone know where to find a trust worthy shop with in the San Francisco bay area?
Thanks
Click to expand...
Click to collapse
I found a pit file and try flashing with Odin, here is the output:
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Set PIT file..
<ID:0/003> DO NOT TURN OFF TARGET!!
<ID:0/003>
<ID:0/003> Re-Partition operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Does that mean my EMMC is corrupted and needs repairing? :crying:
Boot into recovery and Factory/Data Reset
See if that helps
Double0EK said:
Boot into recovery and Factory/Data Reset
See if that helps
Click to expand...
Click to collapse
unfortunately, I can't get into recovery.
when I press volume up+home+power button, I just get a flashing Samsung Galaxy 2 logo (aka boot loop hell)
onqq said:
unfortunately, I can't get into recovery.
when I press volume up+home+power button, I just get a flashing Samsung Galaxy 2 logo (aka boot loop hell)
Click to expand...
Click to collapse
Get the tar file for the most recent TWRP and Odin that. Boot into recovery and factory reset. Try booting normally. If that fails try to Odin the UVALJ1 tar by MrRobinson. (2-3 times). Try booting normally. Once you can boot normally go ahead and try the MK7 tar.

flash grand i9082 failing

Hey guys!
Im trying to flash the stock rom, but I just wont work.
Logs:
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I9082XXUBMGA_I9082OXEBMGA_I9082XXUBMGA_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> vc-firmware.img
<ID:0/003> NAND Write Start!!
<ID:0/003> boot.img
<ID:0/003> recovery.img
<ID:0/003> BcmCP.img
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
I get failure are BcmCP.img
I am using a Odin 3.04
Still getting error, tried different USB ports, different cables, plenty different things
Can someone help? My phone is unusable

Noob in distress!

Update!! Please delete this tread. problem solved. im an idiot sorry.
Hello everyone! So i have softbricked my SM-T210 (without the R). I had it running perfectly with CWM recovery with AICP Nougat. I'm not sure what i broke but it won't boot into Recovery or System. I tried using Odin to reflash the custom recovery which Odin marked as successful (first CWM then when that wouldn't boot i did TWRP). After that I tracked down the stock rom and attempted to Odin flash that which came back as a fail.
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T210XXBOA3_T210BTUBOA2_Home.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> PBL.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Productive assistance would be greatly appreciated! thanks for reading.

Categories

Resources