Recovering an Acer A200 and sharing - Upgrading, Modifying and Unlocking

Even being a SW and HW developer for a long time, I did had to spend some time to learn all the buzzwords in the "Android rooting" world to recover my Acer A200 tablet, so I'm sharing to save other people time:
My kid tried to guess the gesture password to play in my tablet, I don't know how many times, locking my Acer A200.
I tried google recovery, but the WiFi was off (and I could'nt turn on as the tablet was locked), so I went to the web to find a solution.
Factory reset seemed like a good one (turn device ON pressing power+down vol and switching the orientation key), it boots, then shows 'erasing user data', then hangs with an error:
Code:
Unrecoverable bootloader error (0x19000008)
Now the device is not booting, it get stuck on Acer logo after animation...
So I tried to use ADB to revert the damage, as indicated in one forum, but USB debug mode was not active when I did the factory reset.
ADB installation itself is unecessarily complicated, and as I cannot find a way to list the device in linux+adb ($>platform-tools/adb devices), even adding it to: /etc/udev/rules.d/51-android.rules (obtained with lsusb)
Code:
#Acer
SUBSYSTEM=="usb", ATTR{idVendor}=="0502", ATTR{idProduct}=="337d", MODE="0666", GROUP="plugdev"
It seems android isn't even booting to enable the debug bridge.
So I went to the "fastboot" as last resource (reboot using power+vol.down+switch.toggle), and did the command:
Code:
android-sdk-linux> platform-tools/fastboot oem unlock
I selected the "open lock" image and rebooted, now it shows: Bootloader v0.03.06-ICS(UnlockMode), but hangs in the same point.
So I downloaded a stock image from:
acertabletforum/stock-ics-recovery-image
Burned it using:
Code:
$> platform-tools/fastboot flash recovery /home/gaglocal/backup/acer/stockrecovery.img
sending 'recovery' (6144 KB)...
OKAY [ 1.882s]
writing 'recovery'...
OKAY [ 2.689s]
finished. total time: 4.571s
Same status after reboot.
So I've downloaded 'stock ROMs' from:
4shared/AcerStockROM
But when I try to write using fastboot:
Code:
error: update package has no android-info.txt or android-product.txt
So it seems this ROM is just for SDcard update (ie.: place the zip file as update.zip in the root of a fat32 sdcard, then boot using power+vol.down to perform the recovery process with it) but it fails and shows a dead android with a red triangle in the belly, not funny.
As the error that shows up when trying to issue the factory reset is after "erasing user data" I decided to do:
Code:
platform-tools/fastboot erase data
erasing 'data'...
FAILED (remote: (00030003))
finished. total time: 0.167s
This indicates this tablet has some HW misconfiguration issue. As some posted, I repeated the proccess a few times - no luck.
So I wrote the CWM 5.5.0.4 image from this forum, rebooted, and performed the sdcard recovery method again.
Same dead droid icon...
Finally I decided to erase the flash again, starting with the cache partition, using fastboot:
Code:
platform-tools/fastboot erase cache
erasing 'cache'...
OKAY [ 1.452s]
finished. total time: 1.453s
Finally, rebooted with the "factory reset" again and it worked!
At least i learned a lot without having to go to the Nvidia very-low level flashing process

A200 dead
gabriel_agm said:
Even being a SW and HW developer for a long time, I did had to spend some time to learn all the buzzwords in the "Android rooting" world to recover my Acer A200 tablet, so I'm sharing to save other people time:
My kid tried to guess the gesture password to play in my tablet, I don't know how many times, locking my Acer A200.
I tried google recovery, but the WiFi was off (and I could'nt turn on as the tablet was locked), so I went to the web to find a solution.
Factory reset seemed like a good one (turn device ON pressing power+down vol and switching the orientation key), it boots, then shows 'erasing user data', then hangs with an error:
Code:
Unrecoverable bootloader error (0x19000008)
Now the device is not booting, it get stuck on Acer logo after animation...
So I tried to use ADB to revert the damage, as indicated in one forum, but USB debug mode was not active when I did the factory reset.
ADB installation itself is unecessarily complicated, and as I cannot find a way to list the device in linux+adb ($>platform-tools/adb devices), even adding it to: /etc/udev/rules.d/51-android.rules (obtained with lsusb)
Code:
#Acer
SUBSYSTEM=="usb", ATTR{idVendor}=="0502", ATTR{idProduct}=="337d", MODE="0666", GROUP="plugdev"
It seems android isn't even booting to enable the debug bridge.
So I went to the "fastboot" as last resource (reboot using power+vol.down+switch.toggle), and did the command:
Code:
android-sdk-linux> platform-tools/fastboot oem unlock
I selected the "open lock" image and rebooted, now it shows: Bootloader v0.03.06-ICS(UnlockMode), but hangs in the same point.
So I downloaded a stock image from:
acertabletforum/stock-ics-recovery-image
Burned it using:
Code:
$> platform-tools/fastboot flash recovery /home/gaglocal/backup/acer/stockrecovery.img
sending 'recovery' (6144 KB)...
OKAY [ 1.882s]
writing 'recovery'...
OKAY [ 2.689s]
finished. total time: 4.571s
Same status after reboot.
So I've downloaded 'stock ROMs' from:
4shared/AcerStockROM
But when I try to write using fastboot:
Code:
error: update package has no android-info.txt or android-product.txt
So it seems this ROM is just for SDcard update (ie.: place the zip file as update.zip in the root of a fat32 sdcard, then boot using power+vol.down to perform the recovery process with it) but it fails and shows a dead android with a red triangle in the belly, not funny.
As the error that shows up when trying to issue the factory reset is after "erasing user data" I decided to do:
Code:
platform-tools/fastboot erase data
erasing 'data'...
FAILED (remote: (00030003))
finished. total time: 0.167s
This indicates this tablet has some HW misconfiguration issue. As some posted, I repeated the proccess a few times - no luck.
So I wrote the CWM 5.5.0.4 image from this forum, rebooted, and performed the sdcard recovery method again.
Same dead droid icon...
Finally I decided to erase the flash again, starting with the cache partition, using fastboot:
Code:
platform-tools/fastboot erase cache
erasing 'cache'...
OKAY [ 1.452s]
finished. total time: 1.453s
Finally, rebooted with the "factory reset" again and it worked!
At least i learned a lot without having to go to the Nvidia very-low level flashing process
Click to expand...
Click to collapse
Could you list the steps you took for the last successful attempt?
I tried all method but stuck at recovery.
Also does following;
"fastboot flash:raw boot boot.img-kernel boot.img-ramdisk.gz
fastboot flash recovery recovery.img"
unable to recover stock.
My bootloader is unlocked
Before Rooting ROM:
Kernel version: 2.6.39.4+
Image version : Acer_AV041_A200_RV10RC02_WW_GEN1
Build No. : Acer_AV041_A200_1.076.00_WW_GEN1

Related

Bootlooping KF, can't access recovery

So I got my Kindle Fire a few months ago, already rooted. I went from TWRP to a CWM-based recovery, and I've been installing ROMs ever since without any issues. I'm currently running a CM9-based ROM, and I decided to play around with the softkeys, because I was tired of the bland white look. So I found some custom softkeys and flashed the .zip. I made sure to make a Nandroid before flashing, of course.
Upon rebooting from the flash, my KF got stuck in a bootloop. No biggie, this has happened before. I shut it down and rebooted to recovery, to restore the backup. But when it boots into recovery, it automatically reflashes the softkeys zip, and then reboots into the never-ending bootloop.
So the KF isn't necessarily bricked, I just can't get into recovery without it flashing a corrupted zip. I've tried two different unbricking tools, neither had any effect on it. Any ideas?
Can you mount SD card in Recovery and delete the Zip file through your PC?
linktohack said:
Can you mount SD card in Recovery and delete the Zip file through your PC?
Click to expand...
Click to collapse
I only wish I could. As soon as I boot into recovery, it flashed the zip, then reboots into the bootloop. I suspect this happens because I used ROM Manager to flash the zip, and recovery hasn't reset itself because the device isn't booting up all the way. So every time I try to access recovery, it performs the last action I gave it, which was to flash the zip.
I hope you aren't using Hashcode's (older) CWMR or you might be looking at a much larger problem.
http://forum.xda-developers.com/showthread.php?t=1651413
I'm not sure what's going on with your device, but the only way I know to get the recovery to do something on start up is to create a /cache/recovery/command file. That file should be a one time use command and get deleted after use, so your report of it happening each time you boot into recovery is puzzling.
If you want to take that out of the equation, I think you should either get to a shell prompt and delete the file manually or erase the cache partition entirely. Try getting to fastboot mode, boot a copy of the TWRP image, and hopefully it won't reboot on you automatically so you can use adb shell. Alternatively, erase the cache partition entirely with fastboot. If you do the latter, you'll probably need to remake the ext4 filesystem on the cache partition. Here are some fastboot references to get you started...
http://forum.xda-developers.com/showthread.php?t=1668159
http://forum.xda-developers.com/showpost.php?p=23747804&postcount=3
kinfauns said:
I hope you aren't using Hashcode's (older) CWMR or you might be looking at a much larger problem.
http://forum.xda-developers.com/showthread.php?t=1651413
I'm not sure what's going on with your device, but the only way I know to get the recovery to do something on start up is to create a /cache/recovery/command file. That file should be a one time use command and get deleted after use, so your report of it happening each time you boot into recovery is puzzling.
If you want to take that out of the equation, I think you should either get to a shell prompt and delete the file manually or erase the cache partition entirely. Try getting to fastboot mode, boot a copy of the TWRP image, and hopefully it won't reboot on you automatically so you can use adb shell. Alternatively, erase the cache partition entirely with fastboot. If you do the latter, you'll probably need to remake the ext4 filesystem on the cache partition. Here are some fastboot references to get you started...
http://forum.xda-developers.com/showthread.php?t=1668159
http://forum.xda-developers.com/showpost.php?p=23747804&postcount=3
Click to expand...
Click to collapse
Thanks for all that, but I managed to fastboot into it, and then wipe system and data. Then I rebooted to recovery and restored my backup. Never fastbooted into a device before, or done anything with adb commands, so it was a fun experience.
same symptoms: KF bootlooping, no recovery
Hi there,
I have a rooted/modded KF with MIUI, FFF 1.4a and TWRP.
After I gave it away to someone, who only "used it", it is now stuck in a bootloop.
I can get into fastboot via fastboot.exe and re-flashed FFF and TWRP, but no change: KF boots with the white/blue logo, I can press the powerbutton to get into recovery, but TWRP doesn´t show up. When I boot normally, it looks the same: Black screen after a few seconds.
I read about the battery issues, so I booted the KF with a fastboot command waiting to the device. The white/blue KF logo showd up and I left the device at the USB port at my PC for a complete night: no change
I tried to set another bootmode via fastboot.exe but the code doesn´t seem to make any difference.
I have a second KF which runs just fine (now with AOKP M5.1).
Is it bricked now?
Elviz42 said:
Hi there,
I have a rooted/modded KF with MIUI, FFF 1.4a and TWRP.
After I gave it away to someone, who only "used it", it is now stuck in a bootloop.
I can get into fastboot via fastboot.exe and re-flashed FFF and TWRP, but no change: KF boots with the white/blue logo, I can press the powerbutton to get into recovery, but TWRP doesn´t show up. When I boot normally, it looks the same: Black screen after a few seconds.
I read about the battery issues, so I booted the KF with a fastboot command waiting to the device. The white/blue KF logo showd up and I left the device at the USB port at my PC for a complete night: no change
I tried to set another bootmode via fastboot.exe but the code doesn´t seem to make any difference.
I have a second KF which runs just fine (now with AOKP M5.1).
Is it bricked now?
Click to expand...
Click to collapse
I'm not an expert on the KF, but from what you've described, I don't think it's bricked. Have you tried fastboot wiping system and data?
Mardenator said:
I'm not an expert on the KF, but from what you've described, I don't think it's bricked. Have you tried fastboot wiping system and data?
Click to expand...
Click to collapse
I just did:
D:\root>tools\fastboot erase system
erasing 'system'... OKAY [ 51.245s]
finished. total time: 51.246s
D:\root>tools\fastboot erase data
erasing 'data'... FAILED (remote: : partition doesn't exist)
finished. total time: 0.002s
D:\root>tools\fastboot erase userdata
erasing 'userdata'... OKAY [108.555s]
finished. total time: 108.577s
D:\root>tools\fastboot reboot
rebooting...
finished. total time: 0.001s
D:\root>​
I tried to get into Recovery but no change.
Maybe it's a problem with TWRP. Have you tried fastboot flashing a CWM-based recovery?
Doesnt sound like you have twrp installed or its broken just resend twrp it should overwrite whatever is there
Thepooch said:
Doesnt sound like you have twrp installed or its broken just resend twrp it should overwrite whatever is there
Click to expand...
Click to collapse
He might want to fastboot erase recovery and then reflash TWRP.
I tried CWM:
D:\root>tools\fastboot flash boot recovery\fff.bin
sending 'boot' (243 KB)... OKAY [ 0.065s]
writing 'boot'... OKAY [ 0.052s]
finished. total time: 0.117s
D:\root>tools\fastboot flash recovery recovery\cwm.img
sending 'recovery' (5198 KB)... OKAY [ 1.321s]
writing 'recovery'... OKAY [ 1.418s]
finished. total time: 2.740s
D:\root>tools\fastboot oem idme bootmode 5001
... OKAY [ 0.667s]
finished. total time: 0.668s
D:\root>tools\fastboot reboot
rebooting...
finished. total time: 0.002s
D:\root>​
No change, same behavior: Starts with white/blue letters and than "off". Entering recovery is not working.
Are you pushing the power button several times quickly when you see the white kindle blue fire and selecting recovery?
---------- Post added at 11:51 AM ---------- Previous post was at 11:49 AM ----------
You need to select with the power button or the new fff will just tell it to boot normal also twrp is better if you intend to flash anything ics related
Thepooch said:
Are you pushing the power button several times quickly when you see the white kindle blue fire and selecting recovery?
Click to expand...
Click to collapse
Yes. I also tried to enter recovery just by setting bootmode to 5001 with fastboot. This didn´t work either.
Try setting the bootmode to normal then use the power button to toggle to recovery after reflashing twrp also how your flashing them is incorrect
---------- Post added at 12:09 PM ---------- Previous post was at 12:00 PM ----------
fastboot -i 0x1949 flash recovery <file path> <name of recovery>
fastboot -i 0x1949 flash bootloader<file path><name of bootloader>
not fff.bin to recovery as you are doing but to bootloader
D:\root>tools\fastboot flash boot recovery\fff.bin
sending 'boot' (243 KB)... OKAY [ 0.065s]
writing 'boot'... OKAY [ 0.052s]
finished. total time: 0.117s
this one is really wrong your flashing the bootloader to the recovery partition dunno your doing something strange and thats your issue
you may wanna use firekit to get your bootloader and recovery correctly sent to avoid further issues http://forum.xda-developers.com/showthread.php?t=1430038
or like this leaving the id out
fastboot flash bootloader \path\to\fff.bin
fastboot flash recovery \path\to\twrp.img
Hi,
i did flash fff.img to boot(loader) , and after that CWM.img to recovery. But the image is in a folder called "recovery", perhaps this was confusing.
you wrote that you flashed it to boot not bootloader but yes its confusing
try again after an erase I guess
fastboot erase bootloader
fastboot erase recovery
or with the id -i 0x1949
Did that, no success:
D:\root>tools\fastboot getvar product
< waiting for device >
product: kindle
finished. total time: 0.000s
D:\root>tools\fastboot erase bootloader
erasing 'bootloader'... OKAY [ 0.511s]
finished. total time: 0.512s
D:\root>tools\fastboot erase recovery
erasing 'recovery'... OKAY [ 2.429s]
finished. total time: 2.429s
D:\root>tools\fastboot flash bootloader recovery\fff.bin
sending 'bootloader' (243 KB)... OKAY [ 0.065s]
writing 'bootloader'... OKAY [ 0.052s]
finished. total time: 0.117s
D:\root>tools\fastboot flash recovery recovery\openrecovery-twrp-blaze-2.1.1.img
sending 'recovery' (5568 KB)... OKAY [ 1.404s]
writing 'recovery'... OKAY [ 0.543s]
finished. total time: 1.947s
D:\root>tools\fastboot reboot
rebooting...
finished. total time: 0.001s
D:\root>​
ok unplug it then hold your power button down for 1 min then power it on use power button to toggle to recovery option in boot menu see what you get if that doesnt work redownload twrp img and send that again without erase also there is a small chance you could be remaining in fastboot but I doubt it try select reset bootmode as well but you have no system at this point so getting to recovery is imperative
What does "fastboot boot twrp.img" do for you?

Format partitions in fastboot mode

Hi, my kf2 is stucked at fastboot, i'm not able to boot into recovery or system, i have succesfully installed fff-1.4a using a factory cable (because it was bricked with the stock bootloader) and have installed the otter2-twrp-2.4.4.0-recovery.img from hashcode..
It boots and i see the blue kindle logo, and have a menu, but when i select recevery it just turns on the amber light and stays there, i have left it for about 5 minutes waiting to see if it get to revery with no luck.
I tried this:
Code:
sudo fastboot -i 0x18d1 getvar product
< waiting for device >
product: kindle
finished. total time: 0.000s
sudo fastboot -i 0x18d1 oem format
...
OKAY [ 0.068s]
finished. total time: 0.068s
Then
Code:
sudo fastboot -i 0x18d1 flash boot fff-u-boot_v1.4a.bin
< waiting for device >
sending 'boot' (243 KB)...
OKAY [ 0.065s]
writing 'boot'...
OKAY [ 0.051s]
finished. total time: 0.115s
sudo fastboot reboot
rebooting...
sudo fastboot -i 0x18d1 flash boot fff-u-boot_v1.4a.bin
< waiting for device >
sending 'boot' (243 KB)...
OKAY [ 0.065s]
writing 'boot'...
OKAY [ 0.051s]
finished. total time: 0.115s
It succeed as you can see, it has the fff bootloader and twrp recovery is installed!!
Then i tried
Code:
sudo fastboot -i 0x18d1 flash zip cm-10.1-20130704-NIGHTLY-otter2.zip
< waiting for device >
sending 'zip' (155204 KB)...
OKAY [ 38.806s]
writing 'zip'...
FAILED (remote: partition does not exist)
finished. total time: 38.813s
It seem like a partition table problem maybe because i'm trying to install Cyanogenmod and not a stock image...
I think maybe i must reformat the partitions but i only have access to fastboot and i have read the documentation of Android Fastboot in OmapPedia but i'm not sure it's a "generic" information and don't want to mess up things more.
I have read many trheads in the forum but all of them use adb and there's not a thread with instructions about it..
Or maybe i need to flash all the images (system, kernel, etc..) with fastboot but i don't know where to get it, the main problem is that i'm not able to boot into recovery and maybe that point to the real problem
Any help is appreciated !!
Thank's
You can't write CyanogenMod from fast boot.
Sounds like somewhere in there you formatted the system partition. You need the stack file on the system partition in order to boot into recovery.
Restore to stock using fast boot and try again.
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
How?
mindmajick said:
You can't write CyanogenMod from fast boot.
Sounds like somewhere in there you formatted the system partition. You need the stack file on the system partition in order to boot into recovery.
Restore to stock using fast boot and try again.
Sent from my SAMSUNG-SGH-I727 using Tapatalk 2
Click to expand...
Click to collapse
Maybe it is the problem as fastboot oem format seems to do the job...
I have downloaded the stock update-kindle-6.3.2_D01E_4110520.bin, please can you point to the thread explainig how to do that using fastboot or it's just as easy as rename the file to update.zip and flash it directly?
Edited: also i'm not completely sure it's a kf2 and can't get a hint on how to discover it without knowing the is version :banghead: I've looked one the motherboard and is a MB0090 F3F.
I've downloaded the stock bin for the kf2 too...
Thank' for your quick reply
Well. If you have a kf2... The update you downloaded is wrong. IT'S FOR THE ORIGINAL KINDLE FIRE.
Without knowing what device u have u better slow down a sec. Any advice i give COULD permabrick u of you're on the wrong device.
What color was the BOX it came in? What is the model# on the back? (Same for kf1 AND 2 BUT NOT THE KF HD 7" OR 8").
Be advised- this device is EASY TO BRICK. BE CAREFUL.
--
Sent from my mind to your screen.
---------- Post added at 02:48 AM ---------- Previous post was at 02:40 AM ----------
Also. The correct update file wont work either.
You can only flash image files from fastboot.
--
Sent from my mind to your screen.
It's apparent you have a KF1 and not a KF2. The command "fastboot -i 0x18d1..." would not work on the KF2 because it still has the stock bootloader (unless something miraculous happened while I was AFK). The stock bootloader has a VID of 1949, and will not answer to commands using a different VID. 18d1 is Goggle's VID and is indicative of having FFF installed (KF1 only).
BTW, the "-i 0x18d1" part is completely unnecessary on FFF.
That's not your biggest problem though....
Code:
sudo fastboot -i 0x18d1 flash boot fff-u-boot_v1.4a.bin
That command is completely wrong. What you're doing there is flashing the bootloader (fff-u-boot_v1.4a.bin) to the boot (kernel) partition. Obviously, there is no way that could possibly would work out for you. After the "fastboot" portion of the command, you need to specify what you want done with the image in question: flash or boot. "Flash" is persistent, "boot" is for one boot only. In the next part of the command, you need to specify which partition the image in question goes to; bootloader, recovery, boot, etc.
What you need to do is get an actual recovery.img and flash it to your recovery partition before you can even think of accessing said recovery to flash a ROM and get your device working again.
soupmagnet said:
It's apparent you have a KF1 and not a KF2. The command "fastboot -i 0x18d1..." would not work on the KF2 because it still has the stock bootloader (unless something miraculous happened while I was AFK). The stock bootloader has a VID of 1949, and will not answer to commands using a different VID. 18d1 is Goggle's VID and is indicative of having FFF installed (KF1 only).
BTW, the "-i 0x18d1" part is completely unnecessary on FFF.
That's not your biggest problem though....
Code:
sudo fastboot -i 0x18d1 flash boot fff-u-boot_v1.4a.bin
That command is completely wrong. What you're doing there is flashing the bootloader (fff-u-boot_v1.4a.bin) to the boot (kernel) partition. Obviously, there is no way that could possibly would work out for you. After the "fastboot" portion of the command, you need to specify what you want done with the image in question: flash or boot. "Flash" is persistent, "boot" is for one boot only. In the next part of the command, you need to specify which partition the image in question goes to; bootloader, recovery, boot, etc.
What you need to do is get an actual recovery.img and flash it to your recovery partition before you can even think of accessing said recovery to flash a ROM and get your device working again.
Click to expand...
Click to collapse
Well you are completely right!! Didn't realize I was flashing it to the kernel partition, I bought this on eBay and it was already bricked, when I used the factory cable first time I got a lab26 device, and it was a 1949 so, if I'm right it's a kf2.
I've already flashed a twrp recovery but it won't boot.. I'll try sintering else and post the results here
Sent from my SPH-D710 using xda premium
LUC4X said:
when I used the factory cable first time I got a lab26 device, and it was a 1949 so, if I'm right it's a kf2.
I've already flashed a twrp recovery but it won't boot.. I'll try sintering else and post the results here
Click to expand...
Click to collapse
No. The stock bootloader on all generations and variants of Kindle Fires have vendor IDs of 1949. The fact that your device responds to the "fastboot -i 0x18d1..." clearly means you have a custom bootloader installed in its place. If you have an actual custom bootloader installed (not 2nd bootloader) then you clearly cannot possibly have a KF2.
In this thread, you say you have installed recovery twice, but the information given seems to suggest otherwise.
So to try and get to the root of the problem, what is the exact command you used to install custom recovery, and what custom recovery (version) did you install?
Glad you are here soupmagnet!
I didn't even look at the commands he was using but i definitely learned stuff from your posts. Thanks again
--
Sent from my mind to your screen.
Commands used
soupmagnet said:
No. The stock bootloader on all generations and variants of Kindle Fires have vendor IDs of 1949. The fact that your device responds to the "fastboot -i 0x18d1..." clearly means you have a custom bootloader installed in its place. If you have an actual custom bootloader installed (not 2nd bootloader) then you clearly cannot possibly have a KF2.
In this thread, you say you have installed recovery twice, but the information given seems to suggest otherwise.
So to try and get to the root of the problem, what is the exact command you used to install custom recovery, and what custom recovery (version) did you install?
Click to expand...
Click to collapse
Sorry guys i was out of town...
These are the commands (bootloader & recovery) i've used till now:
sudo fastboot -i 0x18d1 flash bootloader fff-u-boot_v1.4a.bin
< waiting for device >
sending 'bootloader' (243 KB)...
OKAY [ 0.065s]
writing 'bootloader'...
OKAY [ 0.083s]
finished. total time: 0.148s
sudo fastboot -i 0x18d1 flash recovery otter2-twrp-2.4.4.0-recovery.img
sending 'recovery' (8153 KB)...
OKAY [ 2.042s]
writing 'recovery'...
OKAY [ 2.705s]
finished. total time: 4.748s
Click to expand...
Click to collapse
Also tryed the twrp from teamw's site in both versions (otter & blaze) just to make sure, by issuing the following commands:
sudo fastboot -i 0x18d1 flash recovery openrecovery-twrp-2.5.0.0-blaze.img
< waiting for device >
sending 'recovery' (6144 KB)...
OKAY [ 1.540s]
writing 'recovery'...
OKAY [ 1.514s]
finished. total time: 3.054s
Click to expand...
Click to collapse
With this, when i reboot and select the recovery it turns on the amber light for 2 seconds and shuts down.
Then when i install the other recovery version (blaze from teamw):
sudo fastboot -i 0x18d1 flash recovery openrecovery-twrp-2.5.0.0-otter.img
< waiting for device >
sending 'recovery' (6144 KB)...
OKAY [ 1.540s]
writing 'recovery'...
OKAY [ 0.684s]
finished. total time: 2.224s
Click to expand...
Click to collapse
When select recovery i get the same result: amber light for 2 seconds and turns off.
And with hashcode otter2-twrp-2.4.4.0-recovery.img:
sudo fastboot -i 0x18d1 flash recovery otter2-twrp-2.4.4.0-recovery.img
< waiting for device >
sending 'recovery' (8153 KB)...
OKAY [ 2.042s]
writing 'recovery'...
OKAY [ 0.894s]
finished. total time: 2.937s
Click to expand...
Click to collapse
It hangs on amber light and i have to manually turn it off holding the power buttom for 10 seconds...
So you think it is a kf1 based on the device id?, it shows that id after i installed the fff-u-boot_v1.4a.bin from hashcode that i intended for the kf2...
Well, based on that i have installed a kf1 bootloader:
Downloaded the Kindle Fire Utility v0.9.9.zip from http://forum.xda-developers.com/showthread.php?t=2192818
Unzipped it (as i'm GNU/Linux)
"Grepped" recursively till find the web address to download files from
Downloaded fff-u-boot_v1.4a.bin
Downloaded openrecovery-twrp-2.4.4.0-blaze.img
Followed the install procedure
Same result !!, still can't get it to boot into recovery...
Really i hope someone here can point me to the right direction to fix this tablet, can't figure out what's wrong with kf(?)
LUC4X said:
So you think it is a kf1 based on the device id?, it shows that id after i installed the fff-u-boot_v1.4a.bin from hashcode that i intended for the kf2...
Well, based on that i have installed a kf1 bootloader:
Downloaded the Kindle Fire Utility v0.9.9.zip from http://forum.xda-developers.com/showthread.php?t=2192818
Unzipped it (as i'm GNU/Linux)
"Grepped" recursively till find the web address to download files from
Downloaded fff-u-boot_v1.4a.bin
Downloaded openrecovery-twrp-2.4.4.0-blaze.img
Followed the install procedure
Same result !!, still can't get it to boot into recovery...
Really i hope someone here can point me to the right direction to fix this tablet, can't figure out what's wrong with kf(?)
Click to expand...
Click to collapse
Lets get a few things clear right off the bat. The file named fff-u-boot_v1.4a.bin is the custom bootloader for the KF1. The bootloader flashed in the KF2 2nd bootloader installation is named otter2-u-boot-prod-10.2.4.bin. If you flash the fff-u-boot_v1.4a.bin (FFF1.4a) onto a KF2, you would end up with something that is slightly less useful than a doorstop.
Why you re-installed it is a mystery to me. You already had FFF1.4a installed. I know this (as I explained earlier) by the fact that your commands, using the "-i 0x18d1" switch, were successful. If you had a stock bootloader, no commands containing that particular vendor ID would work at all. If you had a KF2, there is absolutely NO WAY you would have a device that responds to fastboot commands using "-i 0x18d1". Even with a modified KF2, with 2nd bootloader installed, the vendor ID would still be 1949 and all fastboot commands must include "-i 0x1949" or they will not work. You can confirm the fact that you have FireFireFire installed by entering a fastboot command without adding "i- 0x18d1". With FireFireFire (KF1 only), the commands will still work because it is unnecessary to specify the vendor ID.
That being said, I'm not entirely sure what's going on with TWRP using both "otter" and "blaze" for the board name (I think it has something to do with Goo Manager?), but anything you get from the TWRP website should work for the KF1 (for the time being at least). Anything you get from Hashcode will be for the 2nd generation KFs.
I would suggest, to avoid complicating things any further, that you download Cannibal Open Touch recovery, confirm that the MD5sums match after downloading, and flash it to recovery in fastboot. COTR only works for the KF1 (not made for the 2nd Generation devices yet) so there is "practically" no way you can get the wrong one. If that works and you still want to try TWRP, download the one for Blaze, check the MD5 (as you should with everything), and try flashing it in recovery again.
If you still can't get your device to boot into recovery, try the command again, but replace the word "flash" with the word "boot" and leave out the partition (i.e. 'fastboot boot openrecovery-twrp-2.4.4.0-blaze.img'). If the device boots into recovery, then you know you have the right one and you may have bad blocks in your recovery partition preventing it from booting, but you won't know for sure without checking a few things out first.
Followed your instructions and get the same result...
Maybe i should install a complete system from fastboot and let it try to boot, but where can i get those files?
What do you think?
soupmagnet said:
Lets get a few things clear right off the bat. The file named fff-u-boot_v1.4a.bin is the custom bootloader for the KF1. The bootloader flashed in the KF2 2nd bootloader installation is named otter2-u-boot-prod-10.2.4.bin. If you flash the fff-u-boot_v1.4a.bin (FFF1.4a) onto a KF2, you would end up with something that is slightly less useful than a doorstop.
Why you re-installed it is a mystery to me. You already had FFF1.4a installed. I know this (as I explained earlier) by the fact that your commands, using the "-i 0x18d1" switch, were successful. If you had a stock bootloader, no commands containing that particular vendor ID would work at all. If you had a KF2, there is absolutely NO WAY you would have a device that responds to fastboot commands using "-i 0x18d1". Even with a modified KF2, with 2nd bootloader installed, the vendor ID would still be 1949 and all fastboot commands must include "-i 0x1949" or they will not work. You can confirm the fact that you have FireFireFire installed by entering a fastboot command without adding "i- 0x18d1". With FireFireFire (KF1 only), the commands will still work because it is unnecessary to specify the vendor ID.
That being said, I'm not entirely sure what's going on with TWRP using both "otter" and "blaze" for the board name (I think it has something to do with Goo Manager?), but anything you get from the TWRP website should work for the KF1 (for the time being at least). Anything you get from Hashcode will be for the 2nd generation KFs.
I would suggest, to avoid complicating things any further, that you download Cannibal Open Touch recovery, confirm that the MD5sums match after downloading, and flash it to recovery in fastboot. COTR only works for the KF1 (not made for the 2nd Generation devices yet) so there is "practically" no way you can get the wrong one. If that works and you still want to try TWRP, download the one for Blaze, check the MD5 (as you should with everything), and try flashing it in recovery again.
If you still can't get your device to boot into recovery, try the command again, but replace the word "flash" with the word "boot" and leave out the partition (i.e. 'fastboot boot openrecovery-twrp-2.4.4.0-blaze.img'). If the device boots into recovery, then you know you have the right one and you may have bad blocks in your recovery partition preventing it from booting, but you won't know for sure without checking a few things out first.
Click to expand...
Click to collapse
Followed your instructions and get the same result...
Maybe i should install a complete system from fastboot and let it try to boot, i've found you uploaded a system.img to androidfilehost...
What do you think?
I posted that ages ago. I'm not even sure what device it's for.
Check the file size. If it's around 350MB go ahead. If it's closer to 500MB then it's probably for the HD.
I can't imagine why you couldn't load recovery using the 'fastboot boot recovery.img' command. Did you receive any errors when trying?
soupmagnet said:
I posted that ages ago. I'm not even sure what device it's for.
Check the file size. If it's around 350MB go ahead. If it's closer to 500MB then it's probably for the HD.
I can't imagine why you couldn't load recovery using the 'fastboot boot recovery.img' command. Did you receive any errors when trying?
Click to expand...
Click to collapse
There's not error message, this is the output:
Code:
sudo fastboot boot CannibalOpenTouch-v2.1_otter.img
< waiting for device >
downloading 'boot.img'...
OKAY [ 1.394s]
booting...
OKAY [ 0.004s]
finished. total time: 1.398s
But it never boots up and stays off.
I'm seriously thinking it may be a hardware failure but i wont give up until i'm completely sure about it.. that's why i though i should reformat partitions at the first time but the fastboot oem format command "seems" to work, perhaps it takes very short time to execute 0.068s and it is a very short time, so i though maybe it isn't really formatting anything, is it a "normal time"?
Right now i'm downloading the file it's 380MB maybe something good could happen!!
I'll try the following and will post the results:
Code:
fastboot flash system system.img
fastboot erase userdata
fastboot erase cache
fastboot reboot
LUC4X said:
There's not error message, this is the output:
Code:
sudo fastboot boot CannibalOpenTouch-v2.1_otter.img
< waiting for device >
downloading 'boot.img'...
OKAY [ 1.394s]
booting...
OKAY [ 0.004s]
finished. total time: 1.398s
But it never boots up and stays off.
I'm seriously thinking it may be a hardware failure but i wont give up until i'm completely sure about it.. that's why i though i should reformat partitions at the first time but the fastboot oem format command "seems" to work, perhaps it takes very short time to execute 0.068s and it is a very short time, so i though maybe it isn't really formatting anything, is it a "normal time"?
Right now i'm downloading the file it's 380MB maybe something good could happen!!
I'll try the following and will post the results:
Code:
fastboot flash system system.img
fastboot erase userdata
fastboot erase cache
fastboot reboot
Click to expand...
Click to collapse
The command 'fastboot oem format' will only make sure the partition layout is stock, it does not format the partitions themselves. The information within the limits of the partitions will remain untouched, so it won't do you much good in this situation. The only way to properly format any partition is with recovery (or 'parted' which is usually run from recovery anyway). Your situation is rather unique because the "fastboot boot' command doesn't write anything to the recovery partition. It loads the disk image you choose, into active memory, as if your computer were a separate partition on which that image is stored. There shouldn't be any reason for it to not work properly.
Try to flash the system partition you downloaded and see how it goes. I would also suggest that you make absolutely sure the md5sums match before installing any image to your device, including the recovery images you downloaded before.
soupmagnet said:
The command 'fastboot oem format' will only make sure the partition layout is stock, it does not format the partitions themselves. The information within the limits of the partitions will remain untouched, so it won't do you much good in this situation. The only way to properly format any partition is with recovery (or 'parted' which is usually run from recovery anyway). Your situation is rather unique because the "fastboot boot' command doesn't write anything to the recovery partition. It loads the disk image you choose, into active memory, as if your computer were a separate partition on which that image is stored. There shouldn't be any reason for it to not work properly.
Try to flash the system partition you downloaded and see how it goes. I would also suggest that you make absolutely sure the md5sums match before installing any image to your device, including the recovery images you downloaded before.
Click to expand...
Click to collapse
Code:
sudo fastboot flash system system.img
sending 'system' (389120 KB)...
OKAY [ 97.308s]
writing 'system'...
OKAY [ 36.819s]
finished. total time: 134.131s
sudo fastboot erase userdata
erasing 'userdata'...
OKAY [116.935s]
finished. total time: 116.935s
sudo fastboot erase cache
erasing 'cache'...
OKAY [ 29.189s]
finished. total time: 29.189s
sudo fastboot reboot
rebooting...
finished. total time: 0.000s
Must be hardware, it's sad... if it where a SMD flash memory i would try to changed it but it's a tyni BGA chip...
Thank you very much for your help
I wouldn't give up just yet. You can still try to usbboot, using the shorting trick.
soupmagnet said:
I wouldn't give up just yet. You can still try to usbboot, using the shorting trick.
Click to expand...
Click to collapse
I'll try tonight !!
Sent from my SPH-D710 using xda premium
soupmagnet said:
I wouldn't give up just yet. You can still try to usbboot, using the shorting trick.
Click to expand...
Click to collapse
./usb_fix_parts_and_install_fff_twrp
Loading FFF through USB...
?
waiting for OMAP44xx device...
sending 2ndstage to target...
waiting for 2ndstage response...
sending image to target...
Fixing partitions...
< waiting for device >
... OKAY
Installing x-loader...
sending 'xloader' (128 KB)... OKAY
writing 'xloader'... OKAY
Flash FFF...
sending 'bootloader' (211 KB)... OKAY
writing 'bootloader'... OKAY
Flash TWRP...
sending 'recovery' (5260 KB)... OKAY
writing 'recovery'... OKAY
Resetting bootmode to standard boot...
... OKAY
Loading TWRP...
downloading 'boot.img'... OKAY
booting... OKAY
Click to expand...
Click to collapse
Same as before, it won't reboot after sending the boot to recovery command and if try to get into recovery it turns off after an amber light..
LUC4X said:
Followed your instructions and get the same result...
Maybe i should install a complete system from fastboot and let it try to boot, but where can i get those files?
What do you think?
Click to expand...
Click to collapse
At the begining i saw you were using "fastboot flash zip...." that's wrong command.. should be "fastboot flash update xxxx.zip"
so if you find the totally package, youcan use it.
also you has mixture the boot.img and bootloader.bin..
recovery is not needed if you can flash the right bootloader and boot.:laugh:

[Q] TIFU going from GPE5.1 Back to Sense, Please help :)

So, the instructions are below pulled out of the Back to Sense thread.(http://forum.xda-developers.com/showthread.php?t=2733523) got to the end of what i've pasted no problems......
Flash 1.54.401.5 firmware from Here
Fastboot Method
Boot device into FASTBOOT mode either by adb reboot bootloader or Vol down & Power (device should show FASTBOOT USB)
Make sure the firmware file to be flashed is in your android folder
Open a command prompt from the folder where fastboot resides. (Hold shift key/right click in the dir to get menu - left click on Open Command Prompt here.)
Run the following commands:
fastboot oem rebootRUU (this will reboot the device into RUU mode in preparation for zip flashing)
fastboot flash zip 1.54.401.5-W_Splash.zip (the name of the zip should EXACTLY match the name of the file you're flashing)
It will fail the first time. Run the same command AGAIN until you see it has flashed successfully.
I repeat - Run the same command TWICE until you see it has flashed successfully.
Once complete, type fastboot reboot-bootloader The hyphen is required.
Everything went well until the after that... I stuffed up royally.. my failure is below...
PS C:\adb> fastboot reboot-bootloader
rebooting into bootloader...
OKAY [ 0.014s]
finished. total time: 0.014s
PS C:\adb> fastboot flash recovery TWRP_Recovery_2.8.6.2_M8_CPTB.img
target reported max download size of 1830711296 bytes
sending 'recovery' (16804 KB)...
OKAY [ 1.515s]
writing 'recovery'...
OKAY [ 0.940s]
finished. total time: 2.455s
fastboot boot TWRP_Recovery_2.8.6.2_M8_CPTB.img
I realize i skipped the below steps...
Boot into stock recovery
Factory reset
Reboot into bootloader
It would seem that what i've gone and done is flashed TWRP into the Boot Partition or something? now whenever i boot up, it won't show the fastboot screen, it goes straight to "entering recovery" and sits there forever.... one thing worth noting, i can see the internal storage(well some of it) the device is recognized in windows and then internal storage is 10.5gb free out of 10.6gb, Navigating to the internal directory shows 3 directories: 0, obb, and TWRP. 0 is a neverending folder. every 3rd layer deep click it shows the root directory again...
Help would be very very much appreciated!
cheers!
EDIT: Sorted! It turns out i'm an idiot and wasn't pushing volume down fast enough to get into bootloader. Sorry guys!!!!
Cameltoemcgee said:
It would seem that what i've gone and done is flashed TWRP into the Boot Partition or something? now whenever i boot up, it won't show the fastboot screen, it goes straight to "entering recovery" and sits there forever....
EDIT: Sorted! It turns out i'm an idiot and wasn't pushing volume down fast enough to get into bootloader. Sorry guys!!!!
Click to expand...
Click to collapse
If the bootloader was overwritten, damaged or corrupted, the phone would be bricked, and the screen would not come on at all.
This is the second post on the first page where the OP solved their own issue. You guys are getting good at fixing your own problems.

Help - I've stuffed my Pixel C up and cant get beyond recovery

Hi everyone,
I was in the process of unlocking my bootloader, flashing a recovery and rooting my Pixel C with the Skipsoft Toolkit when something went wrong.
The bootloader unlocked (30 sec screen and chirp) and I flashed TWRP but it got stuck there.
TWRP kept asking for the password to decrypt data, and now everytime I start my Pixel C it goes straight there again.
I've tried different options in the Skipsoft Toolkit but nothing seems to work and goes back to the 'Mount Decrypt Data' TWRP screen.
A few things that Ive tried are listed below.
Any help with me getting back to stock and having the Pixel C working again would be greatly appreciated.
Thankyou
4. Root/UnRoot/Disable Encryption/Flash Stock Boot/Check Root Status [ADB Mode]
7. Unroot, Uninstall Busybox and Restore Stock Boot/Recovery [ADB Mode]
1. Push file, reboot to Custom Recovery and install manually [simplest method]
Working out the best location to set for Internal Storage..
Waiting for Adb Mode ...
Device mode detected [recovery adb]
Android Version Detected: 7.1.2 Serial Number:
Pushing Unroot-SuperSU.zip to: /sdcard/
root\Unroot-SuperSU.zip: 1 file pushed. 0.1 MB/s (3574 bytes in 0.064s)
File/s pushed successfully
Device mode detected [recovery adb]
Device Serial Number:
Rebooting to Fastboot Mode and continuing..
Device mode detected: Fastboot Mode
Device Serial Number:
Device Bootloader State: Locked
Booting TWRP recovery-twrp-3.1.1.1-ryu.img ..
creating boot image...
creating boot image - 13051904 bytes
downloading 'boot.img'...
OKAY [ 0.323s]
booting...
FAILED (remote: image verification failed)
finished. total time: 0.328s
An Error Occured
Press any key to return to the Main Menu..
5. Rename Recovery Restore Files [Fix system flashing stock recovery on boot]
Device Bootloader State: Locked
Booting TWRP recovery-twrp-3.1.1.1-ryu.img ..
creating boot image...
creating boot image - 13051904 bytes
downloading 'boot.img'...
OKAY [ 0.331s]
booting...
FAILED (remote: image verification failed)
finished. total time: 0.331s
An Error Occured
Press any key to return to the Main Menu..
9. Download/Extract/Flash Google Factory Stock Image [Flash Part or Whole Rom]
2. Flash Google Stock Image [in the put_google_factory_image_here\device folder]
image-ryu-opm1.171019.015.zip
ryu-opm1.171019.015-factory-64c65be2.zip
Are you ready to proceed? Type y[yes] or n[no]:
Google Stock Image found [.zip format] in the correct folder.
Filename of image to flash: ryu-opm1.171019.015-factory-64c65be2.zip
Processing archive: put_google_factory_image_here\GooglePixelC\image-ryu-opm1.171019.015.zip
Extracting android-info.txt
Extracting boot.img
Extracting cache.img
Extracting recovery.img
Extracting system.img
Extracting vendor.img
Everything is Ok
Starting Flash Process..
Flashing Bootloader Image..
target reported max download size of 268435456 bytes
sending 'bootloader' (16384 KB)...
OKAY [ 0.416s]
writing 'bootloader'...
FAILED (remote: unsupported command)
finished. total time: 0.431s
An error occured when flashing the image
Try rebooting the device manually back to fastboot mode:
1. Unplug the usb cable
2. Stand the tablet in landscape mode [power button on top] and Press and Hold the
Power and Volume Down buttons for 10-15 seconds until it reboots to Bootloader
mode. Then select 'Switch to fastboot mode' using the volume button and press
the power button. The device will say 'Waiting for fastboot command...'
From the main menu in the Toolkit choose the Download/Extract/Flash menu, then
select Flash previously downloaded image.
Sometimes there is a glitch in the flash process and doing it again will fix it.
You can skip the password and change data file system partition to ext3. Then install custom systems like lineage os.
rhmanoa said:
You can skip the password and change data file system partition to ext3. Then install custom systems like lineage os.
Click to expand...
Click to collapse
Hi and thanks for the response.
How do I change data file system partition to ext3?
I can skip the decrypt password screen in TWRP and go into the general settings, but I dont know how to convert the system partition to ext3.
Thanks
Go to wipe data/cache then advanced wipe then change partition setting select data partition change to ext3.

HELP! Pixel 2 XL may be bricked

Long story short, I attempted to flash the first 9.0.0 factory image and now my phone is seemingly bricked. I keep getting errors that say that fastboot can't detect the current slot. When I try to manually select the slot with --set-active=a/b it returns with my device doesn't support slots. If I try to flash anything individually like the bootloader/radio cmd/powershell just sits there with the "_" underscore blinking for all eternity. TWRP is already flashed and when I try to boot to it it sits on the splash screen indefinitely. I can't fastboot boot TWRP either because I can't flash anything. Deuce's script did the same thing. I tried 3 different cables and am using a brand new computer and latest Platform Tools.
Should I contact google for a warranty replacement? I don't have the order # but that should be irrelevant I think since this phone is still under a year old.
Any ideas????
fastboot: error: Failed to identify current slot
rebooting into bootloader OKAY [ 0.003s]
Finished. Total time: 0.003s
fastboot: error: Failed to identify current slot
rebooting into bootloader OKAY [ 0.004s]
Finished. Total time: 0.004s
extracting android-info.txt (0 MB) to RAM...
--------------------------------------------
Bootloader Version...: TMZ12g
getvar:version-baseband FAILED (remote: unknown command)
fastboot: error: requirements not met!
Press any key to exit...
Update: I installed Android Studio and subsequently, the USB drivers from the SDK manager and somehow I got the phone to boot again. I still cannot flash anything though, I still get the "unable to identify current slot error above.
I hate the the windows Powershell. I always open a command window and work from that.
Make sure you have the most current drivers, and that USB debugging is turned on.
From the horror stories I've read, i always always always do an adb or fastboot devices before i do anything.
If you flash a factory image, don't unzip the file inside the factory image. The flash all.bat file expects that zip to be there.
I've also gotten into the habit of booting the phone that has just been flashed before I root it.
Have you wiped the cache's? Done a reset?
Just throwing things out there...
Good luck I hope you get it all sorted out.

Categories

Resources