[Q] LG Flashtool back to stock PROBLEMS!!! - Sprint LG G2

I have used all drivers and two different tot files, and it works to reboot, then it fails when I try to get past the first welcome screen... Does it make a difference if the sim card is in or out???
It makes it to preactivation and set phone name, then a second or two later goes back into the reboot stage.
I made it to the settings screen and phone info, and all areas were UNKNOWN

pitbull8265 said:
I have used all drivers and two different tot files, and it works to reboot, then it fails when I try to get past the first welcome screen... Does it make a difference if the sim card is in or out???
It makes it to preactivation and set phone name, then a second or two later goes back into the reboot stage.
I made it to the settings screen and phone info, and all areas were UNKNOWN
Click to expand...
Click to collapse
I don't know what went wrong but since you don't have a reply I'll say this... I would start from scratch. Download the tot file AND dll again to a new place on your PC (like desktop). Run LG flash tool again and browse to those 2 files (flash tools likes to remember previous settings). Flash again and let us know the result. Sim card doesn't make a difference.
http://downloads.codefi.re/autoprime/LG/LG_G2/LS980/Stock_Firmware if you need it, always flashed reliably for me.

...
scottdanpor said:
I don't know what went wrong but since you don't have a reply I'll say this... I would start from scratch. Download the tot file AND dll again to a new place on your PC (like desktop). Run LG flash tool again and browse to those 2 files (flash tools likes to remember previous settings). Flash again and let us know the result. Sim card doesn't make a difference.
http://downloads.codefi.re/autoprime/LG/LG_G2/LS980/Stock_Firmware if you need it, always flashed reliably for me.
Click to expand...
Click to collapse
Ive done this.. no luck

pitbull8265 said:
Ive done this.. no luck
Click to expand...
Click to collapse
Did you get anywhere with this? Under status, is your IMEI listed as unknown? This seems like your efs partition might be messed up. Did you make a backup of it?

scottdanpor said:
Did you get anywhere with this? Under status, is your IMEI listed as unknown? This seems like your efs partition might be messed up. Did you make a backup of it?
Click to expand...
Click to collapse
I just read elsewhere that if you used ioroot you may have a backup anyways. On the computer in ioroot. You may find a couple files called, modem st1, and modem st2.
Hopefully they will speak of it. Watch this thread..,.
http://forum.xda-developers.com/showthread.php?p=51932057
@scottdanpor for the info and hopefully how to use it.
pitbull8265 said:
Ive done this.. no luck
Click to expand...
Click to collapse
Sent from my Nexus 7 using Tapatalk

secret.animal said:
I just read elsewhere that if you used ioroot you may have a backup anyways. On the computer in ioroot. You may find a couple files called, modem st1, and modem st2.
Hopefully they will speak of it. Watch this thread..,.
http://forum.xda-developers.com/showthread.php?p=51932057
@scottdanpor for the info and hopefully how to use it.
Sent from my Nexus 7 using Tapatalk
Click to expand...
Click to collapse
Yeah but he has basically access to download mode and fastboot it seems. I haven't found a way to push files without at least recovery
Well, if he has access to stock recovery should be able to push files that way through ADB

NOPE
scottdanpor said:
Yeah but he has basically access to download mode and fastboot it seems. I haven't found a way to push files without at least recovery
Well, if he has access to stock recovery should be able to push files that way through ADB
Click to expand...
Click to collapse
it just hangs and reboots still... cant access fastboot.. tried every file available nothing is working

rrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrrr
scottdanpor said:
Yeah but he has basically access to download mode and fastboot it seems. I haven't found a way to push files without at least recovery
Well, if he has access to stock recovery should be able to push files that way through ADB
Click to expand...
Click to collapse
I have a recovery I made using twrp saved to my pc, and I chose the option to backup my efs, so all of my info is on my pc in the backup file.
HOW can I use adb sideload or ADB to push it to my phone???
HAS TO BE DONE FROM STOCK RECOVERY ADB, as i cant even get into the ui long enough to activate usb debugging

pitbull8265 said:
I have a recovery I made using twrp saved to my pc, and I chose the option to backup my efs, so all of my info is on my pc in the backup file.
HOW can I use adb sideload or ADB to push it to my phone???
HAS TO BE DONE FROM STOCK RECOVERY ADB, as i cant even get into the ui long enough to activate usb debugging
Click to expand...
Click to collapse
It will take a bit of reading but you will learn a lot!
Here's a guide with some commands, you just need to tailor it to your needs/paths, it says Samsung but all you need are the commands.
http://forum.xda-developers.com/showthread.php?t=2141817
If you have ioroot on your computer you have ADB. Plug in your phone in recovery mode and check device manager. It's probably under "unknown" as LG-LS980. You need to right-click and select "update driver", then manually select driver. From the list, you should be able to find something like Android composite ADB device. Select that one and it should then be recognized as ADB.
Hold Shift and right click on the ioroot folder and select "Open command window here", then in cmd type "adb devices". If all is good you will get a serial number as it detects your device. Once you got this you are ready to enter commands, check that guide for the right command to push the file to: /dev/block/platform/msm_sdcc.1/by-name/
as stated by Autoprime here: http://forum.xda-developers.com/showthread.php?t=2451390
I hope that's enough info to get you going. You should type "adb shell" first in ADB so you have access to root.
---------- Post added at 09:12 AM ---------- Previous post was at 09:03 AM ----------
Oh crap... I just re-read that. I don't think this will work if your backup is from TWRP. That needs to be restored from TWRP. Do you not have a backup from ioroot? That contains the img files you need.
---------- Post added at 09:18 AM ---------- Previous post was at 09:12 AM ----------
Ok, I found this...
"Even though all TWRP backup files carry the extension .win, they are either tar archives or filesystem images. System, data, cache and .android_secure are backed up as tar archives or gnu-zipped tar archives if compression is enabled. You can rename those .win files to .tar (.tar.gz if compressed) and extract them like a regular archive. Boot and recovery partitions are backed up as .img files using dd"
from: http://forum.xda-developers.com/showthread.php?t=1694617
I couldn't find out if TWRP backs up EFS to .tar or .img. Once you figure that out you should be able to rename them to modemst1.img and modemst1.img. I just verified on mine that the files are the same size, so I would guess they are actually img files and not compressed. They should be 3MB in size.
There's a lot more info in that thread by Autoprime that should help.

Related

Speed bump in Rooting process...

Hey guys, I am in the process of rooting my evo 4g using this method http://htcevohacks.com/htc-evo-hacks/how-to-root-htc-evo-4g-on-hboot-2-18-with-s-off/ since I have 2.18 hboot version. I have unzipped all the files from RootEvo4GNew, and the file recovery-RA-supersonic-v2.3.img does not have the .img extension on it when I unzip it to the correct folder, and when I try to flash that in the cmd prompt it says
unknown partition 'recovery-RA-supersonic-v2.3.img'
error: cannot determine image filename for 'recovery-RA-supersonic-v2.3.img
I am assuming it can't find the file because it doesn't have the extendion .img on it once extracted. Any ideas? The icon next to the file looks like a zip file and can't be opened by 7zip
See it looks like a winzip file instead of a image file
Ok so I uninstalled winzip and now just have 7zip and it now shows the file as an .img file but I am still getting the same error message when in the command prompt. What am I doing wrong? Here's another image to show you what I mean
furrycnorm said:
Ok so I uninstalled winzip and now just have 7zip and it now shows the file as an .img file but I am still getting the same error message when in the command prompt. What am I doing wrong? Here's another image to show you what I mean
Click to expand...
Click to collapse
Download one of these,it has install instructions and a few different custom recoveries to choose from,creds to Smelkus of course..... http://forum.xda-developers.com/showthread.php?t=2171460
Diablo67 said:
Download one of these,it has install instructions and a few different custom recoveries to choose from,creds to Smelkus of course..... http://forum.xda-developers.com/showthread.php?t=2171460
Click to expand...
Click to collapse
I downloaded and followed instructions, isn't working for me. It looks like the phone doesn't see the file when in bootloader, not sure if I renamed it right.
furrycnorm said:
I downloaded and followed instructions, isn't working for me. It looks like the phone doesn't see the file when in bootloader, not sure if I renamed it right.
Click to expand...
Click to collapse
Follow this http://windows.microsoft.com/en-US/windows-vista/show-or-hide-file-name-extensions to make sure the file extensions show correctly, and make sure you didn't dupe the extension.
sent from a jb ROM..... cause I'm likely testing.
Wambo_Bomb said:
Follow this http://windows.microsoft.com/en-US/windows-vista/show-or-hide-file-name-extensions to make sure the file extensions show correctly, and make sure you didn't dupe the extension.
sent from a jb ROM..... cause I'm likely testing.
Click to expand...
Click to collapse
Thanks for the advice, I think this may work as I did have one extension duped. Problem is when I run the recovery it says it's an older version than what I already have installed and asks if I want to restart the device. I also still can't get the phone to flashboot recovery recovery-RA-supersonic-v2.3.img and it still says unrecognized partition in the command prompt. Is there a way to flash this from the sc card or anything else you can think of to try?
furrycnorm said:
Thanks for the advice, I think this may work as I did have one extension duped. Problem is when I run the recovery it says it's an older version than what I already have installed and asks if I want to restart the device. I also still can't get the phone to flashboot recovery recovery-RA-supersonic-v2.3.img and it still says unrecognized partition in the command prompt. Is there a way to flash this from the sc card or anything else you can think of to try?
Click to expand...
Click to collapse
Are you trying to fastboot flash the recovery .img file to your phone? If so you need to use the command "fastboot flash recovery *insert file name here*" (without quotation marks or asterisks). The recovery img file has to be in your ADB tools folder, alstherwise, put the recovery PC36IMG.zip file in the root folder of your SD card, make sure it's named PC36IMG.zip with no extra .zip extension, and reboot your bootloader. Follow the on-screen prompts to update your recovery.
Sent from my EVO using xda premium
FinZ28 said:
Are you trying to fastboot flash the recovery .img file to your phone? If so you need to use the command "fastboot flash recovery *insert file name here*" (without quotation marks or asterisks). The recovery img file has to be in your ADB tools folder, alstherwise, put the recovery PC36IMG.zip file in the root folder of your SD card, make sure it's named PC36IMG.zip with no extra .zip extension, and reboot your bootloader. Follow the on-screen prompts to update your recovery.
Sent from my EVO using xda premium
Click to expand...
Click to collapse
wow I am retarded, my problem the whole time was that I was typing this:
fastboot flash recovery-RA-supersonic-v2.3.img
when I should have typed this:
fastboot flash recovery recovery-RA-supersonic-v2.3.img
Thank you so much for the help, on to the next step and hopefully this works!
Ok, successfully rooted with s-off! I have read through all the guides, and am still a bit confused because most of them are from 2010 and 2011. I need to flash a rom that will work with metro-pcs. Can you guys help me with which steps I need to take? I tried to download metrodroid v4 but the download link isn't working. Will aall of the roms in this thread work with metro pcs or do I need a specific one? http://forum.xda-developers.com/showthread.php?t=2318070
Also, once I have a rom flashed, do I have to go in to a metro pcs store to get it activated (I do not currently have a metro pcs account or other metro phone) or can I get the esn activated online or by calling there 800 number?

Stucked at TMobile 4G LTE Screen (settings.db mess)

Hello,
I was trying to edit my note 3 settings.db file to add the MobileData toggle at the notification panel.
After I edited the file, I rebooted the phone and Now I am stucked at the Tmobile 4G lte screen.
I have saved the original settings.db file so I can replace the modified one but the problem is that now that the phone doesn't turn on I can't replace it.
Is there anyway to fix this without installing everything from zero again???
Thank You
P.s
I tried to boot in safe mode but the phone doesn't boot even like this.
I tried to wipe cache, but nothing changed
As for the recovery mode, I can boot there
Boot to recovery and use adb console from your pc to swap the files. Learn some Linux command line commands if you don't know how. Primarily you will use cp target.file destination . file. Make a backup if you want via mv.
Sent from my SM-N900T using Tapatalk
howetechnical said:
Boot to recovery and use adb console from your pc to swap the files. Learn some Linux command line commands if you don't know how. Primarily you will use cp target.file destination . file. Make a backup if you want via mv.
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
Any help will be very appreciated as I never worked with Linux.
My original files are located at Downloads folder of my device.
and the files that I changed are located at /data/data/com.android.providers.settings/databases/
What command should I use to copy settings.db from downloads to the databases location
Thnx again for your reply
Cheers
I am trying something like this:
adb push /sdcard/downloads/settings.db sdcard/data/data/com.android.providers.settings/databases/
But I am getting error:closed
Maybe I am entering the paths on the wrong way
howetechnical said:
Boot to recovery and use adb console from your pc to swap the files. Learn some Linux command line commands if you don't know how. Primarily you will use cp target.file destination . file. Make a backup if you want via mv.
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
Another question, as I am not managing to over pass this error close message from adb.
If I install 4.4.2 again from download mode will I lose my settings, applications and everything else that I have installed before???
Odin doesn't wipe anything, but the re install would overwrite much of your personalizations. Boot into recovery, do a nandroid backup, then boot into download and Odin and restore. When you're up again, download nandroid manager from play store and select what you want to restore from your nandroid backup you made. Be sure to save it in a persistent partition, external SD if possible.
Sent from my SM-N900T using Tapatalk
howetechnical said:
Odin doesn't wipe anything, but the re install would overwrite much of your personalizations. Boot into recovery, do a nandroid backup, then boot into download and Odin and restore. When you're up again, download nandroid manager from play store and select what you want to restore from your nandroid backup you made. Be sure to save it in a persistent partition, external SD if possible.
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
Before I try this, another idea that came to my mind.
Is there any program that I can install to my computer and allows me to browse my phone files even when it is in recovery mode???
Adb, like I suggested first. Look on YouTube if you're not sure how to use it.
Sent from my SM-N900T using Tapatalk
howetechnical said:
Adb, like I suggested first. Look on YouTube if you're not sure how to use it.
Sent from my SM-N900T using Tapatalk
Click to expand...
Click to collapse
THNX for your help.
I was forced to do a factory reset through recovery mode and right now phone is up and running.
Just did a restore from kies but it was an old backup that didnt have everything, so trying to install the other tolls that I need.
Thnx again for you help
Cheers

f*cked up phone

first of all i want to say that I almost know nothing about rooting and stuff.
I rooted my phone with the all-in-one toolkit and actually didn't know what I was doing. I was just clicking next and did what the screen told me to do. Everything went great and i had no problems until know. I downloaded and flashed the venom dotview tweak but it didn't work and the normal dot view which I reinstalled also didnt work so I decided to do a recovery from the settings app. it was really stupid to do that beacause my softkeys and statusbar are gone know and the flashed apps are still there. Is there a way to have my phone like it was when I bought it? I don't need a root anymore, I just want my phone getting to work normal.
Thanks
CrankyPants said:
first of all i want to say that I almost know nothing about rooting and stuff.
I rooted my phone with the all-in-one toolkit and actually didn't know what I was doing. I was just clicking next and did what the screen told me to do. Everything went great and i had no problems until know. I downloaded and flashed the venom dotview tweak but it didn't work and the normal dot view which I reinstalled also didnt work so I decided to do a recovery from the settings app. it was really stupid to do that beacause my softkeys and statusbar are gone know and the flashed apps are still there. Is there a way to have my phone like it was when I bought it? I don't need a root anymore, I just want my phone getting to work normal.
Thanks
Click to expand...
Click to collapse
Restore you stock ROM nandroid. Look for it in here COLLECTION of Stock backup's seeing as you really didn't bother to provide us with the relevant and more important information such as the CID and Main software version you were on before you decided to mess your phone up and I doubt you made a backup of your device before doing it.
Is your phone still recognized by a pc?
If so, just load another ROM on your sd card.. Wipe everything and flash through recovery. You'll lose all your data, but your phone will be back.
Since you are new to this - CONGRATS! You just learned the most important rule of flashing. Always make a backup first!
Good luck man. It's an easy fix.
I guess I will be the "bad guy" but why are you messing with your phone when you have no clue what you are doing?
Everyone starts somewhere. Im sure we all learned a lot of what we know now by making lots of stupid mistakes. This logic rings true for life... not just phones.
lucas.scott said:
Is your phone still recognized by a pc?
If so, just load another ROM on your sd card.. Wipe everything and flash through recovery. You'll lose all your data, but your phone will be back.
Since you are new to this - CONGRATS! You just learned the most important rule of flashing. Always make a backup first!
Good luck man. It's an easy fix.
Click to expand...
Click to collapse
yes and no, my pc sees him but the phone folder is empty en htc manager gives an error. any idee how to put a rom on the phone?
CrankyPants said:
yes and no, my pc sees him but the phone folder is empty en htc manager gives an error. any idee how to put a rom on the phone?
Click to expand...
Click to collapse
Unlock bootloader,install a custom recovery via adb then download a custom rom of your choice then move it to ext/internal sd.you may use otg.Then go to the custom recovery(TWRP/Cwm/philz) wipe then install zip through the location.
Jyotirdeb said:
Unlock bootloader,install a custom recovery via adb then download a custom rom of your choice then move it to ext/internal sd.you may use otg.Then go to the custom recovery(TWRP/Cwm/philz) wipe then install zip through the location.
Click to expand...
Click to collapse
How to install a custom recovery via adb and what is adb?
sorry I don't know anything
CrankyPants said:
How to install a custom recovery via adb and what is adb?
sorry I don't know anything
Click to expand...
Click to collapse
This is why you shouldn't use all in one toolkits, you don't learn anything like that and if you're not willing to learn then you probably shouldn't mess around with these things in the first place, expect others to then fix the problems for you. I'm not trying to be mean here, just stating fact.
Download the Android SDK
After downloading, extract the .zip file. Then go into folder inside the sdk folder you'll find a folder named "platform-tools" right click that folder and copy it on your desktop(Ease of access). Inside that platform-tools folder you'll find the applications adb and fastboot.
Download HTC Sync Manager in order to install the drivers(If you haven't done so already and just to be sure).
Download custom recovery, either Philz CWM Recovery or TWRP Recovery . Place the downloaded .img recovery file inside the platform-tools folder.
Make sure your phone has USB-Debugging enabled, if you don't have developer mode on phone. Go to Settings > About > Software Information > More > Tap 7times on Build Number. This will enable developer options. Go back to Settings and scroll down to Developer Options, open it and enable USB Debugging.
Connect your phone to the PC, make sure to accept any prompts that might appear on the phone then inside the platform-tools folder, hold shift then right click, then select "Open Command prompt here". Type adb devices if adb picks up your device it'll show you your devices serial number. Next type adb reboot bootloader to boot into bootloader mode then type fastboot devices again just to make sure the device is connected and being picked up by the prompt. Type fastboot flash recovery name_of_recovery_you_downloaded.img MAKE SURE you type in the correct name for the recovery, exactly the same!!!
When it's done, flash ROM of your choice.
I'm a beginner too, but I learnt loads from watching videos from a channel called Sakitech on YouTube. I watched them over a few times to understand the process before doing anything.
Unlook bootloader:
https://www.youtube.com/watch?v=rEVSfwXsx-c&index=3&list=PLRt6ru-Tz2f4tMLvv9wm9yyiW9mTeVIGA
Turn S-Off:
https://www.youtube.com/watch?v=--Hlms1BuPg&list=PLRt6ru-Tz2f4tMLvv9wm9yyiW9mTeVIGA&index=4
Install a custom recovery and root your phone
https://www.youtube.com/watch?v=WuHFcGvUjwA&feature=youtu.be
Install a custom rom:
https://www.youtube.com/watch?v=t4KeVs5axtM
Remember to backup before you put your phone under serious surgery!
https://www.youtube.com/watch?v=eda67mn-oXc
Hope this helps.
leongwengheng said:
I'm a beginner too, but I learnt loads from watching videos from a channel called Sakitech on YouTube. I watched them over a few times to understand the process before doing anything.
Unlook bootloader:
https://www.youtube.com/watch?v=rEVSfwXsx-c&index=3&list=PLRt6ru-Tz2f4tMLvv9wm9yyiW9mTeVIGA
Turn S-Off:
https://www.youtube.com/watch?v=--Hlms1BuPg&list=PLRt6ru-Tz2f4tMLvv9wm9yyiW9mTeVIGA&index=4
Install a custom recovery and root your phone
https://www.youtube.com/watch?v=WuHFcGvUjwA&feature=youtu.be
Install a custom rom:
https://www.youtube.com/watch?v=t4KeVs5axtM
Remember to backup before you put your phone under serious surgery!
https://www.youtube.com/watch?v=eda67mn-oXc
Hope this helps.
Click to expand...
Click to collapse
Good choice on the videos, these days reading is a bit to tedious for most people. Heck, they don't even read "STOP" on the STOP signs anymore, just drive straight past
I have a super short attention span so I need YouTube to learn anything in life lol.
Sent from my HTC One_M8 using XDA Free mobile app
leongwengheng said:
I have a super short attention span so I need YouTube to learn anything in life lol.
Sent from my HTC One_M8 using XDA Free mobile app
Click to expand...
Click to collapse
Good luck at school then and later on in your job
Lucky boy having such a commited community here. You could've quite easily ended up with a £600 paper weight. Might want to show some appreciation to everyone holding your hand through a process that you should've read about before doing anything. Must admit, I did like the 'I just kept hitting next without knowing what I was doing', that's probably the best thing I've read lol lol.
Sent from my HTC One_M8 using XDA Premium 4 mobile app
BerndM14 said:
This is why you shouldn't use all in one toolkits, you don't learn anything like that and if you're not willing to learn then you probably shouldn't mess around with these things in the first place, expect others to then fix the problems for you. I'm not trying to be mean here, just stating fact.
Download the Android SDK
After downloading, extract the .zip file. Then go into folder inside the sdk folder you'll find a folder named "platform-tools" right click that folder and copy it on your desktop(Ease of access). Inside that platform-tools folder you'll find the applications adb and fastboot.
Download HTC Sync Manager in order to install the drivers(If you haven't done so already and just to be sure).
Download custom recovery, either Philz CWM Recovery or TWRP Recovery . Place the downloaded .img recovery file inside the platform-tools folder.
Make sure your phone has USB-Debugging enabled, if you don't have developer mode on phone. Go to Settings > About > Software Information > More > Tap 7times on Build Number. This will enable developer options. Go back to Settings and scroll down to Developer Options, open it and enable USB Debugging.
Connect your phone to the PC, make sure to accept any prompts that might appear on the phone then inside the platform-tools folder, hold shift then right click, then select "Open Command prompt here". Type adb devices if adb picks up your device it'll show you your devices serial number. Next type adb reboot bootloader to boot into bootloader mode then type fastboot devices again just to make sure the device is connected and being picked up by the prompt. Type fastboot flash recovery name_of_recovery_you_downloaded.img MAKE SURE you type in the correct name for the recovery, exactly the same!!!
When it's done, flash ROM of your choice.
Click to expand...
Click to collapse
I have one problem. Since I don't have the notification bar anymore, the phone doesn't notificate me. How will I get the USB notification to work?
CrankyPants said:
I have one problem. Since I don't have the notification bar anymore, the phone doesn't notificate me. How will I get the USB notification to work?
Click to expand...
Click to collapse
If there's a pop up it'll show on screen, have you tried the adb devices command to see if your phone gets picked up?
Out of curiousity though, when you used the toolkit didn't you have to enable USB Debugging anyway? I'm not familiar with the toolkit, don't use it myself...? If you already enabled it then it's fine, as long as adb devices picks up your device then you're good to go.
BerndM14 said:
If there's a pop up it'll show on screen, have you tried the adb devices command to see if your phone gets picked up?
Out of curiousity though, when you used the toolkit didn't you have to enable USB Debugging anyway? I'm not familiar with the toolkit, don't use it myself...? If you already enabled it then it's fine, as long as adb devices picks up your device then you're good to go.
Click to expand...
Click to collapse
My device is already wiped so I have no configurations anymore.
I have no softkeys and no statusbar anymore since I recovered my phone with the settings app. So no statusbar means no pop-ups.
The adb devices command sees my device in the list of devices but next to it, it says 'offline'. when normaly it has to say 'device'.
CrankyPants said:
My device is already wiped so I have no configurations anymore.
I have no softkeys and no statusbar anymore since I recovered my phone with the settings app. So no statusbar means no pop-ups.
The adb devices command sees my device in the list of devices but next to it, it says 'offline'. when normaly it has to say 'device'.
Click to expand...
Click to collapse
You see it's supposed to throw a small pop up on the screen of the phone where it wants you to accept the RSA key to connect it to PC. It doesn't have anything to do with the softkeys or the notification bar on the top, it's supposed to be on the screen. I take it you probably can't even get into app drawer anymore in order to go to settings. Doesn't give any pop up on the screen... I think you really did f*** up your device
Did you use Hasoon2000's all in one toolkit? If so you probably had to have flashed a custom recovery, it's like the very next thing to do after you unlock bootloader?
BerndM14 said:
You see it's supposed to throw a small pop up on the screen of the phone where it wants you to accept the RSA key to connect it to PC. It doesn't have anything to do with the softkeys or the notification bar on the top, it's supposed to be on the screen. I take it you probably can't even get into app drawer anymore in order to go to settings. Doesn't give any pop up on the screen... I think you really did f*** up your device
Did you use Hasoon2000's all in one toolkit? If so you probably had to have flashed a custom recovery, it's like the very next thing to do after you unlock bootloader?
Click to expand...
Click to collapse
les us assume he is in stock.So he should have a stock recovery.now Boot into fastboot get the details fastboot getvar all.you will find the mid of your choice.download international fw's ruu open the zip there will be an android-info.txt file.edit the file with your mid(change 0P6B10000 to 0P6BXXXXX) where XXXXX represents your mid.then flash the ruu via recovery.Since he connects his device adb will at least detect it (i hope).
Also open toolkit on the right side it is written "next flash a recovery". Connect your phone and simply select twrp and press flash recovery.this should do it.For more details ask hasoon.
Jyotirdeb said:
les us assume he is in stock.So he should have a stock recovery.now Boot into fastboot get the details fastboot getvar all.you will find the mid of your choice.download international fw's ruu open the zip there will be an android-info.txt file.edit the file with your mid(change 0P6B10000 to 0P6BXXXXX) where XXXXX represents your mid.then flash the ruu via recovery.Since he connects his device adb will at least detect it (i hope).
Also open toolkit on the right side it is written "next flash a recovery". Connect your phone and simply select twrp and press flash recovery.this should do it.For more details ask hasoon.
Click to expand...
Click to collapse
To get getvar all you'll need fastboot commands, will fastboot commands even work if he MIGHT not have enabled USB Debugging or for that matter haven't accepted the RSA key?
That's why I asked about the recovery as well though. I saw that on hasoon's toolkit the flashing of a custom recovery was like the next step on the process which means that this guy should at least have a custom recovery already installed.

--[FIX]--SkyDragon G3 USB Fix

Like many of you new flashers, I have flashed the SkyDragon ROM and have noticed that there is no connectivity to the computer whatsoever, so I did a little digging. I went back and forth between 2 Nandroid backups and kept flashing parts of them until I could narrow down where this problem was coming from. I found out that it comes from the specific folder - data/property
There is a missing file called persist.sys.usb.config ,13B in size, and I have no idea what it does (maybe some of you could enlighten me) but throwing the old file into that folder, changing the permissions to rw-------- and rebooting worked like a charm.
I apologize for not sticking this into the development thread, however I'm a lurker with no input! :victory:
Without further ado,
I TAKE NO RESPONSIBILITY FOR ANY BORKEN DEVICES. IF YOU DON'T KNOW WHAT YOU'RE DOING, DON'T DO IT!
1. Download Root Browser and RB Text Editor
2. Navigate to /data/property
3. On the bottom bar, tap the "New" button
4. Click on "New file"
5. Enter the file name as follows:
persist.sys.usb.config
6. Click the file you just made and hit "Open as..."
7. Hit "Text file"
8. Click RB Text editor
9. Delete whatever is there and enter as follows:
auto_conf,adb
No spaces or caps!
10. Save the file by clicking the save button on the top right corner.
11. Reboot your phone
12.Profit
----------------------------------------------------------------------------------------------------------------------------------------
Steal this information, spread it around, someone post it to the development thread and make this ROM better!
If you're having any problems, don't hesitate to ask
i could just drop this in the proper location before flashing the rom yes ??
CheesyNutz said:
i could just drop this in the proper location before flashing the rom yes ??
Click to expand...
Click to collapse
Only if you're going to dirty flash it, but at that point, I'd just dirty flash it anyways. The file should already be there if you're on a ROM that can recognize your phone. I also do recommend a clean flash. I'm sorry if I made this difficult. When flashing the rom, it'll format /data which is where the file is held so if you had the file there already, it would just wipe it.
88keys6strings said:
Only if you're going to dirty flash it, but at that point, I'd just dirty flash it anyways. The file should already be there if you're on a ROM that can recognize your phone. I also do recommend a clean flash. I'm sorry if I made this difficult. When flashing the rom, it'll format /data which is where the file is held so if you had the file there already, it would just wipe it.
Click to expand...
Click to collapse
i was talking from a clean install
drop file in the proper location then wipe phone flash rom with new file and them proceed to set up the phone
CheesyNutz said:
i was talking from a clean install
drop file in the proper location then wipe phone flash rom with new file and them proceed to set up the phone
Click to expand...
Click to collapse
As long as it's after the wipe then yes. If you opened up the zip that contains the ROM, you could head into /data then create a new folder called property and throw the file in there then zip it back up and flash it. But you MUST put the file in /data/property AFTER you flash the ROM. You could drop the file into a downloads or media folder because those don't get touched then flash the rom then move it and change permissions then reboot as well.
So no, you cannot drop the file in it's PROPER location before you wipe, otherwise it'll get deleted. However, you can copy/paste it into say, mnt/sdcard/Download, via your root browser, beforehand then follow my instructions
I'll try when I get home in about six hours.
partylikeaninjastar said:
I'll try when I get home in about six hours.
Click to expand...
Click to collapse
For sure! Will await results
I hope the developers get to see this for the next update
I tried creating my own file as per the instructions (came to 13b size for the file too), but my phone isn't being recognized in android file transfer.
Then again, it wasn't recognized either when I was on stock rom (prior to flashing anything).
On my phone, the file already existed. Its contents read....
Code:
boot,adb,mtp
I changed it accordingly based on your instructions, reboot and nothing.
I found that if you turn USB debugging off, then on again, the file will get overwritten with the original code...boot,adb,mtp.
Could it be that this command simply enables USB debugging? That's what my testing showed. I turned off debugging, made the file change, reboot and debugging was enabled. Disable debugging and the file gets overwritten. Rinse, repeat. If I delete the file, it is recreated when enabling USB debugging....boot,adb,mtp.
Just a preliminary finding. I'm not well versed enough to explain or troubleshoot it any further. It did nothing to cure my USB problem.
Cablespider said:
On my phone, the file already existed. Its contents read....
Code:
boot,adb,mtp
I changed it accordingly based on your instructions, reboot and nothing.
I found that if you turn USB debugging off, then on again, the file will get overwritten with the original code...boot,adb,mtp.
Could it be that this command simply enables USB debugging? That's what my testing showed. I turned off debugging, made the file change, reboot and debugging was enabled. Disable debugging and the file gets overwritten. Rinse, repeat.
Just a preliminary finding. I'm not well versed enough to explain it further. It did nothing to cure my USB problem.
Click to expand...
Click to collapse
I may have overlooked something. I deleted some usb portion of the build.prop. Didn't change anything so i didnt think about it. If you make a backup then edit it deleting the usb part, then reboot that might get it to work.If you need specifics, I'll be next to a computer in about an hour and a half
Can someone just post the file here?
Sent from my LG-D851
---------- Post added at 10:44 PM ---------- Previous post was at 10:36 PM ----------
I copied one of the persist.sys files from that folder to my sdcard and edited it with Rom Toolbox Pro. I opened it as a text file and deleted what was there, then added the stuff in the OP and saved. I then renamed the file to persist.sys.usb.config and added it to that folder and changed permissions and rebooted. Worked fine.
Sent from my LG-D851
Skizzy034 said:
Can someone just post the file here?
Sent from my LG-D851
---------- Post added at 10:44 PM ---------- Previous post was at 10:36 PM ----------
I copied one of the persist.sys files from that folder to my sdcard and edited it with Rom Toolbox Pro. I opened it as a text file and deleted what was there, then added the stuff in the OP and saved. I then renamed the file to persist.sys.usb.config and added it to that folder and changed permissions and rebooted. Worked fine.
Sent from my LG-D851
Click to expand...
Click to collapse
Awesome! Glad it worked for you
This is from my stock rom with the modified skydragon kernel. place in root\data\property. let me know if this works. just rename it and drop the .zip part.
Cablespider said:
On my phone, the file already existed. Its contents read....
Code:
boot,adb,mtp
I changed it accordingly based on your instructions, reboot and nothing.
I found that if you turn USB debugging off, then on again, the file will get overwritten with the original code...boot,adb,mtp.
Could it be that this command simply enables USB debugging? That's what my testing showed. I turned off debugging, made the file change, reboot and debugging was enabled. Disable debugging and the file gets overwritten. Rinse, repeat. If I delete the file, it is recreated when enabling USB debugging....boot,adb,mtp.
Just a preliminary finding. I'm not well versed enough to explain or troubleshoot it any further. It did nothing to cure my USB problem.
Click to expand...
Click to collapse
Jephre said:
I tried creating my own file as per the instructions (came to 13b size for the file too), but my phone isn't being recognized in android file transfer.
Then again, it wasn't recognized either when I was on stock rom (prior to flashing anything).
Click to expand...
Click to collapse
partylikeaninjastar said:
I'll try when I get home in about six hours.
Click to expand...
Click to collapse
CheesyNutz said:
i was talking from a clean install
drop file in the proper location then wipe phone flash rom with new file and them proceed to set up the phone
Click to expand...
Click to collapse
UPDATED
Much easier now. Just tested it with a Nand that didn't work at all and followed the instructions and it worked flawlessly. Let me know if you have any more issues
aclegg2011 said:
This is from my stock rom with the modified skydragon kernel. place in root\data\property. let me know if this works. just rename it and drop the .zip part.
Click to expand...
Click to collapse
It should work just fine as long as you didn't actually compress it lol. Thank you for the upload!
ALSO
THIS IS MY 10TH POST!!! DEV SECTION HERE I COME!! :victory:
88keys6strings said:
1. Download Root Browser and RB Text Editor
2. Navigate to /data/property
3. On the bottom bar, tap the "New" button
4. Click on "New file"
5. Enter the file name as follows:
persist.sys.usb.config
6. Click the file you just made and hit "Open as..."
7. Hit "Text file"
8. Click RB Text editor
9. Delete whatever is there and enter as follows:
auto_conf,adb
No spaces or caps!
10. Save the file by clicking the save button on the top right corner.
11. Reboot your phone
12.Profit
Click to expand...
Click to collapse
I can now confirm that this does work. I now have working MTP again.
You guys could try adding "persist.sys.usb.config=mtp,adb" to the build.prop and see if that works.

[Q] everybody~need the I467 4.4.2 NI2 STOCK RECOVERY file! PLZ!!!!!

My I467 because I wanted ROOT. I was in a state with ODIN 4.4.2 NI2 4.1.2MF1 firmware upgrade
Now the plate could not be activated ..
I find all posts
Only find NI2 the boot.img file .. Is there NI2 official reocvery file?
If there is an official RECOVERY .... flat NI2 should be able to seek to live together!
Posts NI2 boot file in the http://forum.xda-developers.com/showpost.php?p=57025810&postcount=18
Request @muniz_ri help! PLZ !!!!!
!!nobody?!
lovehuiping said:
!!nobody?!
Click to expand...
Click to collapse
How would one pull a Recovery/img? I'll gladly help in any way
K1979C20 said:
How would one pull a Recovery/img? I'll gladly help in any way
Click to expand...
Click to collapse
Need root to pull image. We ain't got no root.
TMartin said:
Need root to pull image. We ain't got no root.
Click to expand...
Click to collapse
Well crap. If we need root in order to pull those, how would we give chainfire the recovery.img so he can make a root?
---------- Post added at 05:12 PM ---------- Previous post was at 04:54 PM ----------
Sorry to double post, but I believe using adb in ubuntu I can pull the recovery.img. Just need to know where to look/file name. Searching "recovery" pulls up quite a number of files. any suggestions?
Recovery partition is located on this block "/dev/block/mmcblk0p10" so if u can pull the block and convert into an img format your good!!! Plus you might wanna pull "/system/etc/recovery-resource.dat" and rename it "recovery-resource.zip
RootSuperSU said:
Recovery partition is located on this block "/dev/block/mmcblk0p10" so if u can pull the block and convert into an img format your good!!! Plus you might wanna pull "/system/etc/recovery-resource.dat" and rename it "recovery-resource.zip
Click to expand...
Click to collapse
I literally had just discovered that mmcblk0p10 is the recovery. Although adb pull of that file fails, it will allow me to adb backup that file. But when it says backup complete on my tablet, the file is nowhere to be found on my computer. not sure where to go from here. Maybe I'm not doing adb backup correctly? Here is the script I entered:
adb backup /dev/block/platform/dw_mmc/mmcblk0p10 C:\backup.ab
But no dice. Backup.ab does not exist in C:/
Edit: found backup.ab after a very long search of my C:\.
Now I just need to find a way to "decrypt" it and convert it.
K1979C20 said:
I literally had just discovered that mmcblk0p10 is the recovery. Although adb pull of that file fails, it will allow me to adb backup that file. But when it says backup complete on my tablet, the file is nowhere to be found on my computer. not sure where to go from here. Maybe I'm not doing adb backup correctly? Here is the script I entered:
adb backup /dev/block/platform/dw_mmc/mmcblk0p10 C:\backup.ab
But no dice. Backup.ab does not exist in C:/
Edit: found backup.ab after a very long search of my C:\.
Now I just need to find a way to "decrypt" it and convert it.
Click to expand...
Click to collapse
Thank every reply, and now can only wait for it?
lovehuiping said:
Thank every reply, and now can only wait for it?
Click to expand...
Click to collapse
Sorry, not sure I understand your question.
Update on my back up file....
I managed to soft brick my laptop while installing Ubuntu. Cant boot into ubuntu, or windows. Also, the power supply on my PC took a dirt nap. So im at a stand still until I can get one of these machines up.and running again.
K1979C20 said:
Sorry, not sure I understand your question.
Update on my back up file....
I managed to soft brick my laptop while installing Ubuntu. Cant boot into ubuntu, or windows. Also, the power supply on my PC took a dirt nap. So im at a stand still until I can get one of these machines up.and running again.
Click to expand...
Click to collapse
thank you,,,PLZ give me links..
TMartin said:
Need root to pull image. We ain't got no root.
Click to expand...
Click to collapse
You can use KingoRoot to root the Note 8.0 i467.

Categories

Resources