Develop Bugs

eastlink sghm919v Canadian s4 keeps failing when flashing stock Rom.

Hey fellow sgh-m919v owners in Canada!
Need some help here!
I am trying to Flash my eastlink wireless sigh-m919v back to stock and uproot it but it keeps failing in different times depending on the Rom I'm flashing.
On the older firmware I downloaded from sammobile.com it almost finishes then gets to modem.bin and says fail(auth) with a big red fail sign. On the phone it says secure check fail:mdm
When I try the newest one it doesn't even want to start. Odin starts then fails right away stating. Fail at sbl2.Mbn and Secure check fail: sbl2 on the phone.
Note when I go into download mode it does state that my phone is a sghm919v, current binary custom, system status custom, csb-oem_config_lbs:0x38 or 0x30. Too small to tell.
Note. I'm able to install custom roms and recoveries fine but not stock roms.
What am I doing wrong? Can someone give me step by step instructions? I'm using a Partially installed stock Rom and want it to be fully installed.
Any help is appreciated

Are you sure you are using the correct Rom...???
There is always the possibility the OS (operating system) you are attempting to install is not the correct one, and thus producing a conflict, and also a negative out come.
Can you post your Model, Make and Carrier, possibly the weblink where you are getting you update from.
Just to get a second opinion, and rule out that you are indeed getting the right download. As each Carrier is hardware sensitive, as to the type of Android OS it supports...

Well im not 100% sure im using the right one but 98% sure I am using the right one.
My phones downlosd mode says its a sgh-m919v. Canadian model of t mobile m919
I got the roms from sammobile.com
I used the firmware ending in esk thinking that meant eastlink but yesterday I doenloaded the wind, mobilicity and videotron versions of samr ftimware to see if yheres any differrnce.
Have yet to try. Will try soon

mikeogden198181 said:
Well im not 100% sure im using the right one but 98% sure I am using the right one.
My phones downlosd mode says its a sgh-m919v. Canadian model of t mobile m919
I got the roms from sammobile.com
I used the firmware ending in esk thinking that meant eastlink but yesterday I doenloaded the wind, mobilicity and videotron versions of samr ftimware to see if yheres any differrnce.
Have yet to try. Will try soon
Click to expand...
Click to collapse
Try to see if you can get your product code
http://forum.xda-developers.com/wik..._Galaxy_S_Series#How_To_Find_Product_Codes.3F

baseballfanz said:
Try to see if you can get your product code
http://forum.xda-developers.com/wik..._Galaxy_S_Series#How_To_Find_Product_Codes.3F
Click to expand...
Click to collapse
download mode states that my product code is a sgh-m919v

just tried flashing the other m919v firmwares from wind, mobilicity and videotron, no luck - fails at modem.bin. whats going on why does it keep failing. very frustrated

this is where it always fails:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919VVLUAMDJ_M919VYVLAMDJ_M919VVLUAMDJ_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Added!!
<ID:0/003> Removed!!
<ID:0/003> Added!!
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> SingleDownload.
<ID:0/003> boot.img
<ID:0/003> NAND Write Start!!
<ID:0/003> recovery.img
<ID:0/003> persdata.img.ext4
<ID:0/003> system.img.ext4
<ID:0/003> modem.bin
<ID:0/003> FAIL! (Auth)
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

bump! any help would be greatly appreciated guys!

Same issue
mikeogden198181 said:
bump! any help would be greatly appreciated guys!
Click to expand...
Click to collapse
I have the same issue... any resolution?... Need some help here... is our bootloader locked?

ryanmillet said:
I have the same issue... any resolution?... Need some help here... is our bootloader locked?
Click to expand...
Click to collapse
It might be all possible that you just have a simple hardware issue.
Instead of trying the latest, can you humor the conversation by trying the first update on the SamMobile site...!!!
Anything but the last or latest, try to roll back as far as you can...!!!

modem.bin is the radio file. does your phone boot into android and work fine after failing at modem.bin or it does not boot.
You can also try different version of Odin say 3.04 or a different usb port or both.
edit
could also be that the firmware file is not fully downloaded.can you check the md5 on the file to be same as that from sammobile.

munchy_cool said:
modem.bin is the radio file. does your phone boot into android and work fine after failing at modem.bin or it does not boot.
You can also try different version of Odin say 3.04 or a different usb port or both.
edit
could also be that the firmware file is not fully downloaded.can you check the md5 on the file to be same as that from sammobile.
Click to expand...
Click to collapse
Nice reply, munchy_cool...!!!
Sent from my SGH-M919 using XDA Premium 4 mobile app

Getting somewhere...
grassy-sneakers said:
It might be all possible that you just have a simple hardware issue.
Instead of trying the latest, can you humor the conversation by trying the first update on the SamMobile site...!!!
Anything but the last or latest, try to roll back as far as you can...!!!
Click to expand...
Click to collapse
OK... so Odin flashing just doesn't work...
the latest based firmware MG1 stops almost instantly with an Sb2 error....
the oldest based firmware MDJ stops at modem install "secure check fail mdm"
I am however able to flash any custom recovery and from there install anything I want via CWM
Now... I was interested in flashing an alternative modem on my M919V (as my research leads me to understand that LTE is disabled on my device) I really wanted to just flash the M919 Modem...
so I searched and searched for a way to flash the modem to another one... all of reading said not to do it... it's too risky, ect.... BUT... some said it can be done and claimed success.... so I gave it a try...
Odin flash of ANY modem gives an error... same "secure check fail mdm" No CWM modem flash exists... I did find some other devices that had CWM modems to flash but flashing them gave a Baseband "unknown" IMEI "unknown"... so that was super scary... until I repacked the CWM modem zip with my device modem and I was back in business....
Long story short... you can't flash anything Via Odin in this phone really except a recovery... everything else pretty much fails which leads me to think either it was something to do with the partition scheme or the bootloader... I'm unsure as I really am not a developer just a daring competent xda rom addict...
IF you are on M919V and wish to flash modems (granted you will want to only flash a modem specific to M919V) examples would be the MG1 or MDJ... I have found a method that works everytime... you will need to have root via CF-ROOT or a custom rom which has root (that you flashed via CMW after to odin flashed a recovery)
here is the link to the instructions...
http://www.alliance-rom.com/communi...-non-hlos-bin-temporary-flashing-method.8676/
I hope this will shed some more light on our device... I really just wish I could convert my device fully to a M919 as this device (M919V) seems to have some weird issues... OR... better yet... a 9505G :highfive:
---------- Post added at 10:07 PM ---------- Previous post was at 10:02 PM ----------
munchy_cool said:
modem.bin is the radio file. does your phone boot into android and work fine after failing at modem.bin or it does not boot.
You can also try different version of Odin say 3.04 or a different usb port or both.
edit
could also be that the firmware file is not fully downloaded.can you check the md5 on the file to be same as that from sammobile.
Click to expand...
Click to collapse
Tried with 3.04 (instead of 3.09) here is my log - on the device it says "secure check fail: mdm"
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> modem.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003>
<ID:0/003> Receive Response from boot-loader
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)

munchy_cool said:
could also be that the firmware file is not fully downloaded.can you check the md5 on the file to be same as that from sammobile.
Click to expand...
Click to collapse
I still want to see if it is not a software issue by trying or playing around with OFFICIAL firmware, before I assume it is just faulty hardware refusing to corporate with your attempts to restore your Canadian Phone.
Again, munchy_cool, Thank you...!!!
Also have you called Samsung, and explained to them and I quote "That your phone failed during an OS update, and you tried to roll back using a download file from SamMobile, and even then you have experienced no success...!!!", just to see if they have on record of the same issues...???
--Just a though..., as I would hate to keep beating around the bush.
---------- Post added at 09:10 PM ---------- Previous post was at 09:04 PM ----------
Also I notice you have multiple choices to download, what one do you say is your version.
-SamMobile-
SGH-M919V - Canadian Firmware

ryanmillet said:
Tried with 3.04 (instead of 3.09) here is my log - on the device it says "secure check fail: mdm"
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> modem.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> Transmission Complete..
<ID:0/003> Now Writing.. Please wait about 2 minutes
<ID:0/003>
<ID:0/003> Receive Response from boot-loader
<ID:0/003> Complete(Write) operation failed.
<ID:0/003> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Click to expand...
Click to collapse
means the modem is invalid for this phone, as mentioned a few posts above there are multiple firmwares for your s4 , you need to know which carrier your s4 is ..there might be checks in the firmware to stop it from being flashed onto another carriers phone even if model number is same.

munchy_cool said:
there might be checks in the firmware to stop it from being flashed onto another carriers phone even if model number is same.
Click to expand...
Click to collapse
Thus the concern of a hardware conflict/issue with being successful in your flash using Odin.
Android devices are not all the same, they change depending on what country you are in especially if you are using a STOCK ROM. Every country has a different setup requirement when it comes to establishing a valid connection, so thus the hardware/software conflict.
Sent from my SGH-M919 using XDA Premium 4 mobile app
---------- Post added at 12:21 PM ---------- Previous post was at 12:12 PM ----------
grassy-sneakers said:
Thus the concern of a hardware conflict/issue with being successful in your flash using Odin.
Android devices are not all the same, they change depending on what country you are in especially if you are using a STOCK ROM. Every country has a different setup requirement when it comes to establishing a valid connection, so thus the hardware/software conflict.
Sent from my SGH-M919 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
Besides that I cannot tell which is yours (meaning Firmware - SamMobile) your post suggest EastLink...??? Is this East Canada...? In East Canada what Carriers to they provide you...?, and what Model# is your phone...?
Maybe we can help to narrow down your Firmware you need...???

If you can also provide your OS - BASEBAND version, under Settings - More - About - Baseband Version.
You should be able to get this from a Custom Rom as well...!
Sent from my SGH-M919 using XDA Premium 4 mobile app

grassy-sneakers said:
If you can also provide your OS - BASEBAND version, under Settings - More - About - Baseband Version.
You should be able to get this from a Custom Rom as well...!
Sent from my SGH-M919 using XDA Premium 4 mobile app
Click to expand...
Click to collapse
My baseband has been flashed as I described in my earlier post... M919VVLUAMDJ.... My Carrier is unknown as I bought this phone unlocked for cheap on kijiji... but the guy said he worked for samsung and it was a spare... (Eastlink was the intended carrier...) although this model has 4 carriers it could potentially be... Eastlink, Wind mobile, ect.... The Op has the EXACT same model number and the EXACT same issue as me... he also has tried flashing literally EVERY firmware available on Sammobile website...

ryanmillet said:
My baseband has been flashed as I described in my earlier post... M919VVLUAMDJ.... My Carrier is unknown
Click to expand...
Click to collapse
(Eastlink was the intended carrier...) although this model has 4 carriers it could potentially be... Eastlink, Wind mobile, ect....
Click to expand...
Click to collapse
The Op has the EXACT same model number and the EXACT same issue as me... he also has tried flashing literally EVERY firmware available on Sammobile website...
Click to expand...
Click to collapse
I have confirmed that M919VVLUAMDJ, is the correct firmware for Canadian model phones, still at a miss, is this is a hardware description, given it is specifically found, i.e. provided visually in the OS.
and you say you have tried EVERY firmware...???
Have you read this yet...???
RUN OTHER CARRIER ROMs on AT&T/TMO/Canadian S4 devices

grassy-sneakers said:
I have confirmed that M919VVLUAMDJ, is the correct firmware for Canadian model phones, still at a miss, is this is a hardware description, given it is specifically found, i.e. provided visually in the OS.
and you say you have tried EVERY firmware...???
Have you read this yet...???
RUN OTHER CARRIER ROMs on AT&T/TMO/Canadian S4 devices
Click to expand...
Click to collapse
I'm downloading all the other firmware for my phone to see what one matches.... I'll let you know the results

Galaxy S3 Major Root Confusion Update!

Hello Please if possible be very Noob friendly with your instructions, thanks
Ok I have a rooted Samsung Galaxy S3 AT&T on Firmware 4.3
So I noticed the 4.4.2 Update came out and i really want to update to it but I couldn't OTA because it would say update failed later discovered this is because my S3 is rooted
Now I am in the middle of trying to unroot my galaxy s3 and am very confused i tried doing backup and reset obviously that didnt work i am very confused on how this Odin software works so if you someone could give me very noob specific directions it would be greatly appreciated!
Thanks in Advance

Just open the SuperSU app and select Full Unroot. Let it do its thing and you're unrooted.
Or follow enewman17's thread for how to update.

I believe unrooting will only be successful if none of the AT&T apps were removed from the device. I forgot about that point and I had to flash the 4.3 stock image in order to successfully install the OTA update to 4.4.2. The OTA will try to patch all that ATT bloat during installation; if its not there it will fail.

DocHoliday77 said:
Just open the SuperSU app and select Full Unroot. Let it do its thing and you're unrooted.
Or follow enewman17's thread for how to update.
Click to expand...
Click to collapse
Yah i already did that but it would still fail the update at 24%

mwrobe1 said:
I believe unrooting will only be successful if none of the AT&T apps were removed from the device. I forgot about that point and I had to flash the 4.3 stock image in order to successfully install the OTA update to 4.4.2. The OTA will try to patch all that ATT bloat during installation; if its not there it will fail.
Click to expand...
Click to collapse
Could you please give me a download link or something to the 4.3 stock image for odin?
Everytime i download one it always some weird files that i do not know how to utilize through odin
So if you could give me a stock 4.3 that would be great thanks

nkhaira said:
Could you please give me a download link or something to the 4.3 stock image for odin?
Everytime i download one it always some weird files that i do not know how to utilize through odin
So if you could give me a stock 4.3 that would be great thanks
Click to expand...
Click to collapse
I used this method in post #1 to go back to stock 4.3: http://forum.xda-developers.com/showthread.php?t=2565972
Contrary to other posts...I only had Auto Reboot checked and that worked for me.
This will also wipe all data from your device...make sure you backup pics/vids/contacts/etc. before you do this.
After you take the OTA update, I can also confirm that TowelRoot will successfully root the ATT GS3 running KitKat. Although the documentation says no reboot is required...I needed a reboot after rooting with towelroot.

mwrobe1 said:
I used this method in post #1 to go back to stock 4.3: http://forum.xda-developers.com/showthread.php?t=2565972
Contrary to other posts...I only had Auto Reboot checked and that worked for me.
This will also wipe all data from your device...make sure you backup pics/vids/contacts/etc. before you do this.
After you take the OTA update, I can also confirm that TowelRoot will successfully root the ATT GS3 running KitKat. Although the documentation says no reboot is required...I needed a reboot after rooting with towelroot.
Click to expand...
Click to collapse
But isnt that for the Sprint Galaxy s3
I have the SGH-i747 AT&T LTE USA Version?

nkhaira said:
But isnt that for the Sprint Galaxy s3
I have the SGH-i747 AT&T LTE USA Version?
Click to expand...
Click to collapse
My sincerest apologies. Correct. I used that link for you because the instructions were clear and concise. The firmware download should be good from here: http://stockroms.net/file/GalaxyS3/SGH-I747/StockROMS.net-SGH-I747_ATT_1_20120522193451.zip

mwrobe1 said:
My sincerest apologies. Correct. I used that link for you because the instructions were clear and concise. The firmware download should be good from here: http://stockroms.net/file/GalaxyS3/SGH-I747/StockROMS.net-SGH-I747_ATT_1_20120522193451.zip
Click to expand...
Click to collapse
Just to make sure this is the file i put in odin so i can go back to stock 4.3 update (non rooted) and update OTA to 4.4.2 right?

nkhaira said:
Just to make sure this is the file i put in odin so i can go back to stock 4.3 update (non rooted) and update OTA to 4.4.2 right?
Click to expand...
Click to collapse
Correct...make sure you put your phone in download mode as well (Hold down Volume Down, Center Home, and Power buttons together for about 10 seconds...When your screen turns off, let go of the Power button but keep holding down Volume Down and Center Home buttons....When you see the warning screen, hit Volume Up button...Connect a microUSB cable from your phone to computer...Run Odin...click on “PDA”, then choose the file you downloaded...click on Start once Odin "loads" the file...wait 10-15 minutes for the flash too occur...after coming back from a reboot you should be on stock 4.3)

mwrobe1 said:
Correct...make sure you put your phone in download mode as well (Hold down Volume Down, Center Home, and Power buttons together for about 10 seconds...When your screen turns off, let go of the Power button but keep holding down Volume Down and Center Home buttons....When you see the warning screen, hit Volume Up button...Connect a microUSB cable from your phone to computer...Run Odin...click on “PDA”, then choose the file you downloaded...click on Start once Odin "loads" the file...wait 10-15 minutes for the flash too occur...after coming back from a reboot you should be on stock 4.3)
Click to expand...
Click to collapse
Thank you for being responsive and helpful
I have started the file download i have slow internet speed at my house but it should download in 30 minutes and in a hour i will update this thread if it worked thanks!

mwrobe1 said:
Correct...make sure you put your phone in download mode as well (Hold down Volume Down, Center Home, and Power buttons together for about 10 seconds...When your screen turns off, let go of the Power button but keep holding down Volume Down and Center Home buttons....When you see the warning screen, hit Volume Up button...Connect a microUSB cable from your phone to computer...Run Odin...click on “PDA”, then choose the file you downloaded...click on Start once Odin "loads" the file...wait 10-15 minutes for the flash too occur...after coming back from a reboot you should be on stock 4.3)
Click to expand...
Click to collapse
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCALEM_I747ATTALEM_I747UCALEM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
That is the error message i am getting.. when i am trying this

nkhaira said:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> I747UCALEM_I747ATTALEM_I747UCALEM_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> aboot.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<OSM> All threads completed. (succeed 0 / failed 1)
That is the error message i am getting.. when i am trying this
Click to expand...
Click to collapse
I'll try to locate the exact MD5 I used and give you a link later today/this week. Sorry for the trouble.

mwrobe1 said:
I'll try to locate the exact MD5 I used and give you a link later today/this week. Sorry for the trouble.
Click to expand...
Click to collapse
Ok As soon as possible would be appreciated currently this is my only phone and i need to use it and I factory reset it yesterday thinking it would get rid of the root i would like to install all my apps and everything as soon as possible thanks

Your Odin flash failed because you tried to flash a much older firmware. LEM. You need to flash the 4.3 firmware. You can use this thread. http://forum.xda-developers.com/showthread.php?t=2722660
Enewman17 has one too I think. Not sure where exactly right now though.

DocHoliday77 said:
Your Odin flash failed because you tried to flash a much older firmware. LEM. You need to flash the 4.3 firmware. You can use this thread. http://forum.xda-developers.com/showthread.php?t=2722660
Enewman17 has one too I think. Not sure where exactly right now though.
Click to expand...
Click to collapse
Thanks for your reply So since this in too many different files what do i do to combine them (noob)? i know its something to the extent of extracting them into one folder?
Could you give me instructions on that

DocHoliday77 said:
Your Odin flash failed because you tried to flash a much older firmware. LEM. You need to flash the 4.3 firmware. You can use this thread. http://forum.xda-developers.com/showthread.php?t=2722660
Enewman17 has one too I think. Not sure where exactly right now though.
Click to expand...
Click to collapse
Ok i got all the files combined now i see a csc a AP file and alot of the file catergories from Odin do i only need the AP file for PDA or do i need to insert each corresponding file into each corresponding category in Odin?

I don't have this device so its apparently a little different than I'm used to in this regard. Check post 13 of that thread to see if that helps. Otherwise someone more familiar with that particular process will need to chime in.

DocHoliday77 said:
I don't have this device so its apparently a little different than I'm used to in this regard. Check post 13 of that thread to see if that helps. Otherwise someone more familiar with that particular process will need to chime in.
Click to expand...
Click to collapse
Thank You So much!!
Sorry for late reply but the download you sent me worked and after 10 minutes i was on stock 4.3 upgraded to 4.4.2 without any problems!!!
THANKS!!!

[Q] GALAXY S4 SGH-M919 Soft brick fix?

It all started when my phone got wet from me jumping into a pool and realizing my phone was in my pocket afterwards, then I put it in rice for 24 hours, battery off the phone of course, then I proceeded to open the phone, dry the motherboard, open the cards and dab them with alcohol and dry them again. THAT, gave my phone life.
THEN, it's stuck on Samsung boot screen, it does not go into recovery and it does go into download mode.
I tried a pda on odin3 v1.85 and this is what I got
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUAMDL_M919TMBAMDL_M919UVUAMDL_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sbl2.mbn
<ID:0/003> NAND Write Start!!
<ID:0/003> sbl3.mbn
<ID:0/003> rpm.mbn
<ID:0/003> aboot.mbn
<ID:0/003>
<ID:0/003> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Any suggestions on what I can do to solve this soft brick type of issue? I was on KitKat btw.

You have to flash a KitKat stock ROM. Can't flash earlier version like MDL.
Sent from my SGH-M919 using Tapatalk

If flashing NB4 firmware won't work, I'm afraid something may have been fried and won't be fixable by firmware flash even if it does turn on and go into download mode

Frankenscript said:
You have to flash a KitKat stock ROM. Can't flash earlier version like MDL.
Sent from my SGH-M919 using Tapatalk
Click to expand...
Click to collapse
I will try to do that now..

YoungCNYC said:
I will try to do that now..
Click to expand...
Click to collapse
i cant do it because my phone doesnt go into recovery, by any chance, do you know how to flash a rom through odin?

Isn't using ODIN what you posted in the first post in this thread?
If you can't get into download mode, you may have a deeper problem. Since you couldn't get into "recovery" I'm guessing one of your buttons isn't working.
If you do get it to download mode, I recommend Odin 3.07 or 3.09 (I use 3.09).

Frankenscript said:
Isn't using ODIN what you posted in the first post in this thread?
If you can't get into download mode, you may have a deeper problem. Since you couldn't get into "recovery" I'm guessing one of your buttons isn't working.
If you do get it to download mode, I recommend Odin 3.07 or 3.09 (I use 3.09).
Click to expand...
Click to collapse
yeah I use odin, but idk how to flash a ROM through it i use 1.85

I'm on my phone at work without easy access to links, but if you Google "flash phone ROM with Odin" you will get many walkthroughs.
You were probably almost there with what you did in your first post. However you used an older version of the stock firmware than was on your phone so it failed. Get the KitKat firmware (NB4) and do what you originally tried.
I also recommend using at least Odin 3.07 though I know 3.09 works because I use it.
Basically boot phone to download mode, attach USB cable, let it recognize phone, open Odin, select your proper stock firmware in I think the second of the four places where you can specify the file, press start. Reboot when done.
Sent from my SGH-M919 using Tapatalk
---------- Post added at 12:10 PM ---------- Previous post was at 12:07 PM ----------
See here ... My attempt to post the link from tapatalk... Sorry if doesn't work...
http://forum.xda-developers.com/showthread.php?t=2816508
Sent from my SGH-M919 using Tapatalk

Frankenscript said:
I'm on my phone at work without easy access to links, but if you Google "flash phone ROM with Odin" you will get many walkthroughs.
You were probably almost there with what you did in your first post. However you used an older version of the stock firmware than was on your phone so it failed. Get the KitKat firmware (NB4) and do what you originally tried.
I also recommend using at least Odin 3.07 though I know 3.09 works because I use it.
Basically boot phone to download mode, attach USB cable, let it recognize phone, open Odin, select your proper stock firmware in I think the second of the four places where you can specify the file, press start. Reboot when done.
Sent from my SGH-M919 using Tapatalk
---------- Post added at 12:10 PM ---------- Previous post was at 12:07 PM ----------
See here ... My attempt to post the link from tapatalk... Sorry if doesn't work...
http://forum.xda-developers.com/showthread.php?t=2816508
Sent from my SGH-M919 using Tapatalk
Click to expand...
Click to collapse
That was great but the link of the thread doesn't work

You flash firmware in Odin, not ROMs.. Don't know if you guys are getting mixed up in this.. All you do is boot to download mode, connect to PC, open Odin, go to PDA, select your firmware and click start

Frankenscript said:
I'm on my phone at work without easy access to links, but if you Google "flash phone ROM with Odin" you will get many walkthroughs.
You were probably almost there with what you did in your first post. However you used an older version of the stock firmware than was on your phone so it failed. Get the KitKat firmware (NB4) and do what you originally tried.
I also recommend using at least Odin 3.07 though I know 3.09 works because I use it.
Basically boot phone to download mode, attach USB cable, let it recognize phone, open Odin, select your proper stock firmware in I think the second of the four places where you can specify the file, press start. Reboot when done.
Sent from my SGH-M919 using Tapatalk
---------- Post added at 12:10 PM ---------- Previous post was at 12:07 PM ----------
See here ... My attempt to post the link from tapatalk... Sorry if doesn't work...
http://forum.xda-developers.com/showthread.php?t=2816508
Sent from my SGH-M919 using Tapatalk
Click to expand...
Click to collapse
serio22 said:
You flash firmware in Odin, not ROMs.. Don't know if you guys are getting mixed up in this.. All you do is boot to download mode, connect to PC, open Odin, go to PDA, select your firmware and click start
Click to expand...
Click to collapse
I already did that and it doesnt go past the samsung boot screen, it doesnt go to recovery either, he might be right but the links of the mega website wont let me download the NB4

YoungCNYC said:
I already did that and it doesnt go past the samsung boot screen, it doesnt go to recovery either, he might be right but the links of the mega website wont let me download the NB4
Click to expand...
Click to collapse
Search for fenny's fixed NB4 firmware and flash that

[Q] Stock international lte version rom

Hi guys, i just purchased the at&t samsung galaxy tab s and got it unlocked. I'm loving it so far, however one thing annoy me is att get rid of the stock phone call and messaging feature. So i wonder if the international lte rom has that option, so i can make phone call and text?

BADBOY1412 said:
Hi guys, i just purchased the at&t samsung galaxy tab s and got it unlocked. I'm loving it so far, however one thing annoy me is att get rid of the stock phone call and messaging feature. So i wonder if the international lte rom has that option, so i can make phone call and text?
Click to expand...
Click to collapse
if you have the 10.5 LTE, I have uploaded latest stock T805 firmware here:
http://forum.xda-developers.com/showthread.php?t=2902557
just flash using ODIN.
Tapatalked from my GALAXY S5

[email protected] said:
if you have the 10.5 LTE, I have uploaded latest stock T805 firmware here:
http://forum.xda-developers.com/showthread.php?t=2902557
just flash using ODIN.
Tapatalked from my GALAXY S5
Click to expand...
Click to collapse
Thanks, will it be compatible with my tablet? I dont want to brick it, also do i need root before flashing the rom?

BADBOY1412 said:
Thanks, will it be compatible with my tablet? I dont want to brick it, also do i need root before flashing the rom?
Click to expand...
Click to collapse
what tablet do you have? no you don't need root.
here is a guide that you can use
http://androidxda.com/flash-samsung-stock-rom-using-odin
ODIN: https://www.google.se/url?sa=t&rct=...=RK0ekg44IHkrmWq59-3jkg&bvm=bv.77648437,d.bGQ

[email protected] said:
what tablet do you have? no you don't need root.
here is a guide that you can use
I have the AT&t version of the galaxy tab s 4gLTE, modelSM- T807A.So i can just flash the T805 rom on top of my existing rom?
Click to expand...
Click to collapse

BADBOY1412 said:
[email protected] said:
what tablet do you have? no you don't need root.
here is a guide that you can use
I have the AT&t version of the galaxy tab s 4gLTE, modelSM- T807A.So i can just flash the T805 rom on top of my existing rom?
Click to expand...
Click to collapse
well it should work, same Exynos 5420 SoC, so just flash it
turn off your tablet, put it on download mode by holding down the home button + volume down and power until you see download mode.
Click to expand...
Click to collapse

[email protected] said:
BADBOY1412 said:
well it should work, same Exynos 5420 SoC, so just flash it
turn off your tablet, put it on download mode by holding down the home button + volume down and power until you see download mode.
Click to expand...
Click to collapse
i tried to flash it with oDin but it failed,i think it has something to do with the MD5,it fail. The status is Leave CS after check MD5,and then fail when i clicked start
Click to expand...
Click to collapse

BADBOY1412 said:
[email protected] said:
i tried to flash it with oDin but it failed,i think it has something to do with the MD5,it fail. The status is Leave CS after check MD5,and then fail when i clicked start
Click to expand...
Click to collapse
hmm, strange, I used it yesterday and flashed my T805, do you choose PDA in ODIN? also do you get the message that your tablet is added in ODIN?
also your quotes looks ****ed up
you can also try to re-download the file again.
Click to expand...
Click to collapse

so you flash your t805 tablet with the t805 rom? i think it failed bc of the different variant. My tab s is t807a so maybe the MD5 doesnt match. Thanks alot for your effort though

BADBOY1412 said:
so you flash your t805 tablet with the t805 rom? i think it failed bc of the different variant. My tab s is t807a so maybe the MD5 doesnt match. Thanks alot for your effort though
Click to expand...
Click to collapse
yes, but try to download the ROM again and see if it works.

[email protected] said:
yes, but try to download the ROM again and see if it works.
Click to expand...
Click to collapse
<ID:0/003> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T805XXU1ANH1_T805XEF1ANH1_T805XXU1ANF6_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/003> Odin v.3 engine (ID:3)..
<ID:0/003> File analysis..
<ID:0/003> SetupConnection..
<ID:0/003> Initialzation..
<ID:0/003> Get PIT for mapping..
<ID:0/003> Firmware update start..
<ID:0/003> sboot.bin
<ID:0/003> NAND Write Start!!
<ID:0/003> FAIL!
<OSM> All threads completed. (succeed 0 / failed 1)
Thats the message i received

hmm, it seems that something is blocking it from flashing, maybe there is something with the T807A that don't allow other stock ROMs to be flashed

[SOLVED] Working link for M919VVLUAMDJ stock rom? (Wind S4)

I need just the modem from this rom, but I would take the whole thing. It's AWOL on Sammobile, usenet, and the wider internet seems devoid of it too. Any help would be greatly appreciated.
Thanks!

Do you want the modem to sim unlock the phone using regionlockaway? If yes, you could try the modem from a mobilicity ROM. Wind/Freedom and Mobilicity used the same model #.

audit13 said:
Do you want the modem to sim unlock the phone using regionlockaway? If yes, you could try the modem from a mobilicity ROM. Wind/Freedom and Mobilicity used the same model #.
Click to expand...
Click to collapse
I get an error in Odin when I tried to flash the T-mobile modem. That said, I've also tried to get the mobilicity rom and same thing - it seems to have disappeared from the internet.
The Wind one is on rapidgator; and I've tried numerous times to download but it always fails partway through.

Are you flashing the entire rom in Odin?

audit13 said:
Are you flashing the entire rom in Odin?
Click to expand...
Click to collapse
No, just the modem. And yes, it's for the purpose of SIM unlock
Thanks.

What is the Odin error? Are you using the original Samsung USB cable?

audit13 said:
What is the Odin error? Are you using the original Samsung USB cable?
Click to expand...
Click to collapse
Original Samsung yes, and here's the log. I've flashed this phone many times with the same cable, same Odin and never had a problem.
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> Modem_UVUAMDL.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> modem.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> FAIL! (Auth)
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)

Look here: http://forum.xda-developers.com/showpost.php?p=70078427&postcount=11

audit13 said:
Look here: http://forum.xda-developers.com/showpost.php?p=70078427&postcount=11
Click to expand...
Click to collapse
Thanks, but that's the same t-mobile modem giving the errors above...

Here y'all go!
Modem Only: M919V_GLW_M919VVLUAMDJ (SGH-M919V Wind/Freedom)
https://www.dropbox.com/s/iqewmm2zr6sgt9u/modem.bin?dl=0
I'll leave it there for a year or so.

it will work on a T-mobile SGH-M919? (not m919V)
---------- Post added at 04:11 PM ---------- Previous post was at 03:52 PM ----------
it will work with a SGH-M919? (not a M919V)
Thanks

Here's a thread about the sgh-m919: http://forum.xda-developers.com/galaxy-s4-tmobile/help/downgrade-4-4-4-to-4-4-2-t3509077

Grievous74 said:
it will work on a T-mobile SGH-M919? (not m919V)
---------- Post added at 04:11 PM ---------- Previous post was at 03:52 PM ----------
it will work with a SGH-M919? (not a M919V)
Thanks
Click to expand...
Click to collapse
No it won't. The T-Mobile modems for M919 are all over the internet though, you can find them anywhere.

Obscenic said:
No it won't. The T-Mobile modems for M919 is all over the internet though, you can find it anywhere.
Click to expand...
Click to collapse
Thanks..
I have the latest M919UVUFOK3
From what I recall the M919V version have newer modem drivers and I was hopping they will work.

Hi, could you please post the link again, its not working anymore.
thanks a ton

sdfjkss said:
Hi, could you please post the link again, its not working anymore.
thanks a ton
Click to expand...
Click to collapse
I may have gotten rid of it. Will check in a few hours when I'm back at my computer.