[Q] Tab 3 10.1" Reboot Loop - Galaxy Tab 3 Q&A, Help & Troubleshooting

So I have a ~week old Tab which I havn't used, I played around with it last night and flashed CWM using Odin and that worked fine. I went and flashed the rooted stock firmware, and it seemed to have flashed fine, except now the tablet is in a reboot loop, it restarts about 3 times and then automatically boots into recovery. I've flashed all the ROMs I can find for the 10.1" and it happens with all of them, last resort is flashing stock recovery then taking it back to the place I bought it from and to play dumb, but I'd rather not. Anyone got any suggestions?
TL;DR Tablet stuck in reboot loop, won't boot ROM, recovery & download mode work fine.

You might have done it, but have you tried flashing back the stock firmware ?
try it and post back please

Agree, I had the same issues with a few of the custom roms. I went back to stock rom and have had no issues. My issue was flashing from a SD card. For some reason it would not work. I put the rom on the device in the download folder and flashed from there. Most roms did flash correctly but I found them to be of little use. Did you by chance do a backup before you started playing around with other roms? Hope so. Then at least you can recover back to factory condition.

Nitro_123 said:
You might have done it, but have you tried flashing back the stock firmware ?
try it and post back please
Click to expand...
Click to collapse
I have, I tried reinstalling my backup, as well as both of the stock roms here, although both times I didn't have a microsd card available, so I sideloaded both of the ROMs (which apparently worked fine, verified etc). I've just gone and bought one, so when I get home tonight I'm going to have another play around and see if I can get something working.
Brian D said:
Agree, I had the same issues with a few of the custom roms. I went back to stock rom and have had no issues. My issue was flashing from a SD card. For some reason it would not work. I put the rom on the device in the download folder and flashed from there. Most roms did flash correctly but I found them to be of little use. Did you by chance do a backup before you started playing around with other roms? Hope so. Then at least you can recover back to factory condition.
Click to expand...
Click to collapse
Interesting, I haven't tried that, I shall, thanks
I might also try flashing the ROM through Odin instead of a recovery.

I do believe that stock roms MUST be uploaded via ODIN. They cannot reside on the device. The stock rom is around 1.9gb (XAR-P5210UEUAMK1). So you will use that file (or whatever stock rom you wish to use). If you are loading one of the other roms developed here then you can put it on the device and load from there (via the recovery app CWM or TWRP)

Brian D said:
I do believe that stock roms MUST be uploaded via ODIN. They cannot reside on the device. The stock rom is around 1.9gb (XAR-P5210UEUAMK1). So you will use that file (or whatever stock rom you wish to use). If you are loading one of the other roms developed here then you can put it on the device and load from there (via the recovery app CWM or TWRP)
Click to expand...
Click to collapse
Oh, damn, really? That would explain quite a lot then, thanks, hopefully I'll be home in a couple hours and can report back

My bad I didn't make myself clear. Yes I meant flashing back a stock ROM via ODIN as that is the best way to restore it to stock. Thanks to @Brian D for pointing that out

Nitro_123 said:
My bad I didn't make myself clear. Yes I meant flashing back a stock ROM via ODIN as that is the best way to restore it to stock. Thanks to @Brian D for pointing that out
Click to expand...
Click to collapse
Haha thanks, I'm downloading a stock rom now, hopefully I'll be able to report back in about 30

Holy ****, thanks guys! Managed to get the stock ROM flashed with Odin, silly me for the not realising. Anyone know what would have caused the boot loop? I really don't want to run the stock rom with all the samsung crap (I guess I can root and remove everything)

I think what you did was called a dirty flash. You had bits and pieces of the original rom on the device when you tried to load another rom. The two mixed like vinegar and oil. You have to wipe your system clean before you can load a new flash. Before proceeding please do a backup of what you have right now. Load either CWM or TWRP and do the backup. My preference is TWRP. I like the look and feel of how it works.
I found the best instruction set to be http://forum.xda-developers.com/showpost.php?p=49715684&postcount=172. I had the same boot loop as you but when I followed these instructions I finally loaded the rom. But like I said, to me I gained nothing by using it. But this is me. After much reading I found that if I just delete bloatware then I should be ok. I used an app called bloatfree from the play store. Worked just great but one has to be careful about what one removes. That is why I always backup before doing anything. I must have had 20 backup files at one time. LOL
Good luck!

Related

Stuck on boot animation after flashing rom

Got my brand new nexus today, rooted it using toolkit, then i wanted to install a rom. Everything went fine, flashed eagle blood, everything went fine. Then i downloaded an app and it took for ever to download so i rebooted my phone, then i was stuck with the dreaded animation lock. Now no matter what i do, i cant get past the animation. Still have access to CWM, tried a factory reset/cache wipe...but no success...
Any idead?
P.S. It's not me, it's my friends nexus! I got skyrocket!
Flash the stock ROM on the phone. You have access to recovery so use it then after you verify you can boot with the stock ROM then try flashing another ROM on again.
Personally as it is your friends phone if (s)he doesn't know how to flash ROMs then I would leave the phone stock.
No idea what caused you from being able to boot to this issue but this is my advice.
by that you mean to what??? because on the skyrocket flashing to stock rom is quite simple, via ODIN + Stock TAR...but how to do it on nexus?
Personally as it is your friends phone if (s)he doesn't know how to flash ROMs then I would leave the phone stock.
Click to expand...
Click to collapse
everybody has to start somewhere...you werent the android dev youself the first time you flashed. I brocked my skyrocket the first hour i got it because of a flailed flash...but today, 2 months later i can do anything with it
polish_pat said:
by that you mean to what??? because on the skyrocket flashing to stock rom is quite simple, via ODIN + Stock TAR...but how to do it on nexus?
everybody has to start somewhere...you werent the android dev youself the first time you flashed. I brocked my skyrocket the first hour i got it because of a flailed flash...but today, 2 months later i can do anything with it
Click to expand...
Click to collapse
Go into cwm, do a wipe and also go into advanced and wipe dalvik. You should then be able to reflash your custom rom to fix your boot loop. If thats successful then go back to cwm and make a NANDROID backup so they have a restore point if anything goes wrong in the future.
If you want to flash back to stock its quite simple and can all be done from my ToolKit. Its basically going to http://code.google.com/android/nexus/images.html and downloading the latest factory rom for your model, moving it to the correct folder in the ToolKit and then selecting option 8 from the ToolKit to extract the images and flash it.
Mark.
polish_pat said:
Got my brand new nexus today, rooted it using toolkit, then i wanted to install a rom. Everything went fine, flashed eagle blood, everything went fine. Then i downloaded an app and it took for ever to download so i rebooted my phone, then i was stuck with the dreaded animation lock. Now no matter what i do, i cant get past the animation. Still have access to CWM, tried a factory reset/cache wipe...but no success...
Any idead?
P.S. It's not me, it's my friends nexus! I got skyrocket!
Click to expand...
Click to collapse
I've run into the same issue tonight going back to Apex 1.0.2 from the 4.0.4 leak. I'm trying the suggestion below to wipe and re-flash the ROM. I'll report back when I'm finished.
Edit: Yep, it worked!

Really weird problems.

This has become quite infuriating.
I was on The Hybrid 1.3 when by phone was randombly freezing. I needed to pull the battery to reset it. This caused ALL of my apps to lose their data. (Facebook was logged out, netflix was logged out, Titanium backup lost its direction to the folder on my SD card)
I thought this was odd, so I downloaded another ROM to try and fix the problem. I downloaded the new rom and went into recovery. Flashed new rom, cleared cache, cleared dalvik, but then as I tried to do a factory reset in CWM my phone resets and comes back to recovery. This happens every single time I try to do it in CWM.
ROM booted fine but has many wierd problems (probably that go with being unable to factory reset)
So i downloaded TWRP and tried flashing that by odin, only to get an unfixable bootloop.
So odin'd back to CWM, factory reset problem still persists.
So at this point I decided to go back to stock and turn this phone in because there is no reason it should be doing this.
And now my frustration about trying to get back to the stock ROM. WHY THE HELL IS THERE NOT AN ODIN FLASHABLE STOCK ROM?! Or any rom for that matter.
In CWM i have to put all .zips on my external SD, because the internal one REFUSES to mount.
The .zip from HERE is not working for me at all. I try to flash it and it says it completes in about a second. I reboot and it just stays at the samsung screen and never goes any further.
I remember back with my Captivate, if anything went wrong as long as you got back into download mode, you could one click odin your way back to normal and start all over. It's like every thread in this devices forum is purposefully vague and confusing, things are not explained well at all and people talk about mysterious version of files and things without ever actually providing a link.
This is becoming a real pain in the ass to try and get my phone back to stock or even useable again. Does anyone have any ideas?
I just tried looking for you and wow, i didn't realize that we really don't have a flashable ODIN stock rom....
best thing i found was...
http://forum.xda-developers.com/showthread.php?t=1992303
Use this toolkit to go back to a stock att galaxy note 2.....http://forum.xda-developers.com/showthread.php?t=2052779
lmike6453 said:
I just tried looking for you and wow, i didn't realize that we really don't have a flashable ODIN stock rom....
best thing i found was...
http://forum.xda-developers.com/showthread.php?t=1992303
Click to expand...
Click to collapse
We do have ODIN flashable stock firmware...(stock rom, kernel, modem, recovery). go the Android DEV forum.. STICKY "One Stop Shop for Note2". In there you'll find everything you need. Look under section 5 "FIRMWARE". You can also go to SamMobile.com website... under "Firmware", and in the search box, type "I317". The downloads are "zip", but those are not flashable zip... download that file and use 7-ZIP to extract the tar (xxxxxx.tar.md5"). Use that tar in Odin. Follow instructions in sticky for how to load file/use Odin if not familiar.

[Q] [SOLVED] T-Mobile Samsung Galaxy S4 (SGH-M919) Soft-bricked

Hi all, hope you are doing well (I also hope that you can help me ).
I just recently got a replacement phone because my other one had a faulty speaker (crackling, etc.). The other one was rooted (via CF-AutoRoot) and had TWRP on it, and I made a complete nandroid backup of it onto my MicroSD card.
I rooted the new phone using CF-AutoRoot via Odin and installed TWRP on it as well (also via Odin). Then I swapped the SD card and SIM card and restored the complete backup to the new phone.
It took a while, but the phone booted up and I had two working clones, the only way to tell which was which was by changing the volume and hearing the crackling on the old one.
So the new phone worked all day (was able to make calls and everything, and the GUI that was customized with Wanam Xposed even looked good), however when I restarted it to put in my backup battery, I didn't have root for some reason. I tried and tried to get it back (reinstalled SuperSU, tried the TWRP method) to no avail.
I re-flashed CF-AutoRoot just to see, and the phone booted up but and for some reason SuperSU was gone (and I didn't have root). When I restarted, I got a boot loop and could not even get back into a recovery.
I got tired of this and wanted a fresh start, so I just flashed the stock ROM via ODIN and did a factory reset. However now if I try to boot, the Samsung logo will flash and just shut down, and I won't be able to get into the recovery no matter what. If I flash a recovery (CWM, TWRP or even stock), the recovery will work until I try to actually try to boot the phone. I've tried taking the battery out for a good 5 minutes and retrying (also tried swapping batteries), I've tried doing complete resets galore from all three recoveries mentioned with no success. Obviously Download mode still works so I know it's not completely bricked, but I am getting a little scared.
Any and all help is extremely appreciated as I would prefer not to have such an expensive paper-weight.
Thanks a bunch!
I would suggest going all the way back stock on stock firmware via Odin. Then re-root, TWRP, and re-download the rom of your choice. Dont restore the backup. Just start fresh.
I Think My S4 Is Insane
SICK MADE DEVELOPMENT
alloycowboy said:
I would suggest going all the way back stock on stock firmware via Odin
Click to expand...
Click to collapse
Thanks for the reply.
And okay, I tried that.
I flashed stock using the T-Mobile ROM I found here: galaxys4root_(dot)_com/galaxy-s4-stock-firmware/
This is the same ROM file I used to completely restore the phone I had to return, and that worked fine.
But it still won't boot up or go into recovery mode (just shows the Samsung logo for a split second before shutting down).
One thing I did do on the other phone was flash a kernel which had set-MUID to off so I could WiFi tether, but I thought flashing the stock ROM would revert that back as well. Do you think that's the reason it messed up so badly? I restored the backup from the other phone with a different kernel? Right after I restored the backup to the new phone and everything was working, I remember checking the kernel info in the About Phone section of the settings, and it was in fact the kernel I'd installed on the other phone.
TLDR: Tried flashing stock ROM to no avail. Download mode still works but can't enter recovery mode or boot.
Are you doing a factory reset after flashing stock firmware?
I Think My S4 Is Insane
SICK MADE DEVELOPMENT
I'd flash a stock rooted ROM. Get that root and recovery back. The konane tar file from the stickies, perhaps.
Sent from my SGH-M919 using xda app-developers app
alloycowboy said:
Are you doing a factory reset after flashing stock firmware?
Click to expand...
Click to collapse
Yeah, as soon as it finished installing I went into stock recovery and did a factory reset.
Karakoram2 said:
I'd flash a stock rooted ROM. Get that root and recovery back. The konane tar file from the stickies, perhaps.
Click to expand...
Click to collapse
Alright, I'll try that.
Is the konane tar an actual ROM? And what do you mean in the stickies?
Sorry, not very familiar with XDA forums.
Samsung GT-I9500 flashes n switches off!
BallisticallySimilar said:
Hi all, hope you are doing well (I also hope that you can help me ).
I just recently got a replacement phone because my other one had a faulty speaker (crackling, etc.). The other one was rooted (via CF-AutoRoot) and had TWRP on it, and I made a complete nandroid backup of it onto my MicroSD card.
I rooted the new phone using CF-AutoRoot via Odin and installed TWRP on it as well (also via Odin). Then I swapped the SD card and SIM card and restored the complete backup to the new phone.
It took a while, but the phone booted up and I had two working clones, the only way to tell which was which was by changing the volume and hearing the crackling on the old one.
So the new phone worked all day (was able to make calls and everything, and the GUI that was customized with Wanam Xposed even looked good), however when I restarted it to put in my backup battery, I didn't have root for some reason. I tried and tried to get it back (reinstalled SuperSU, tried the TWRP method) to no avail.
I re-flashed CF-AutoRoot just to see, and the phone booted up but and for some reason SuperSU was gone (and I didn't have root). When I restarted, I got a boot loop and could not even get back into a recovery.
I got tired of this and wanted a fresh start, so I just flashed the stock ROM via ODIN and did a factory reset. However now if I try to boot, the Samsung logo will flash and just shut down, and I won't be able to get into the recovery no matter what. If I flash a recovery (CWM, TWRP or even stock), the recovery will work until I try to actually try to boot the phone. I've tried taking the battery out for a good 5 minutes and retrying (also tried swapping batteries), I've tried doing complete resets galore from all three recoveries mentioned with no success. Obviously Download mode still works so I know it's not completely bricked, but I am getting a little scared.
Any and all help is extremely appreciated as I would prefer not to have such an expensive paper-weight.
Thanks a bunch!
Click to expand...
Click to collapse
The same thing has happened to me! Did you find any solustion for this?? Please help!! This was my first attempt and i have no idea wats going on!
Here are the stickies for our forum: http://forum.xda-developers.com/showthread.php?t=2419828
Sent from my SGH-M919 using XDA Premium 4 mobile app
What I did to unbrick my T-Mobile S4 (SGH-M919)
killerwolf2121 said:
The same thing has happened to me!
Did you find any solutions for this? Please help if you can; this was my first attempt and I have to idea what's going on.
Click to expand...
Click to collapse
Well, for the first problem, flashing the stock ROM did it for me. I followed this tutorial.
For the second issue of not booting up after displaying the Samsung logo; my battery just simply was too dead and didn't have enough juice to start. You have no idea how stupid I felt.
Let your phone charge from the wall cable for a good while before trying all this again; then see if that works. It did it for me. If it doesn't, I'm not sure what else to try.
After that (if it works), if you still want root, just flash CF-Auto-Root and then a custom recovery if you want (like ClockworkMod Recovery (click the little version link, not the "Download ROMs" button) or TWRP via GooManager) (I use TWRP)
All the best and let me know how it went!
Keep in mind that I did this on an SGH-M919 (T-Mobile S4) running Android 4.2.2, so if you don't have that, I have no idea if any of the above will work for you. Also I'm pretty sure if you do have 4.3, you will ruin your warranty forever due to the Knox restriction they added (if you haven't already).
Android_Monsters said:
Here are the stickies for our forum: http://forum.xda-developers.com/showthread.php?t=2419828
Click to expand...
Click to collapse
Thanks
BallisticallySimilar said:
Well, for the first problem, flashing the stock ROM did it for me. I followed this tutorial.
For the second issue of not booting up after displaying the Samsung logo; my battery just simply was too dead and didn't have enough juice to start. You have no idea how stupid I felt.
Let your phone charge from the wall cable for a good while before trying all this again; then see if that works. It did it for me. If it doesn't, I'm not sure what else to try.
After that (if it works), if you still want root, just flash CF-Auto-Root and then a custom recovery if you want (like ClockworkMod Recovery (click the little version link, not the "Download ROMs" button) or TWRP via GooManager) (I use TWRP)
All the best and let me know how it went!
Keep in mind that I did this on an SGH-M919 (T-Mobile S4) running Android 4.2.2, so if you don't have that, I have no idea if any of the above will work for you. Also I'm pretty sure if you do have 4.3, you will ruin your warranty forever due to the Knox restriction they added (if you haven't already).
Thanks
Click to expand...
Click to collapse
I am on 4.3 and yes, flashing the stock rom worked for me too! relief thanks a ton!
Having trouble unbricking M919 T-Mobile
Hi, I'm trying to unbrick my M919 through Odin. I have all the updated software, but I keep getting a fail message. Any help would be appreciated.

[Q] So I Dove Into Rooting

so i recently dove into rooting my s4 after first spending a lot of time reading this great board, thought i had a handle on it, thought things were going very well, but i've hit a snag, which came while attempting my first restore - i'm hopeful someone will give me a little help,
a little background:
1. before rooting i backed up my phone with titanium, also backed it up by copying all of its contents to my pc.
2. i followed the excellent "[SGH-M919] CF-Auto-Root" instructions and it worked without a hitch, it was a quick and easy process, no surprises.
3. confirmed that i was rooted using "root checker", all systems were go.
4. once the root was done i made another backup using titanium and sms backup. i also made a full system backup using online nandroid pro and, to be extra safe, i also backed up efs using efs backup tool.
5. i then moved some folders and files to my external card and once again backed up my phone as before, including to my pc.
6. feeling confident that i could now restore my system to its rooted stock state if things went south, i decided to flash my first rom with cwm, i went with cm11 m7 4.4.3 - i saved the cm11 and gapps zips to my external card using rom tool box pro, rebooted into cwm recovery, selected the two files, and flashed. i also did a data and cache wipe before doing so.
6. needless to say i was thrilled when cm11 loaded perfectly, it worked great, and it was just what i was hoping for.
7. having been bitten by the apparent ease of flashing roms, i decided to restore my system to it's pre cm11 state, to it's rooted stock rom state, and try another rom, rather than just flash another rom from cm11 - i wanted to make sure that returning to my rooted stock rom state would be a simple matter.
and that's where i've run into problems.
1. as i mentioned i made two system backups of my stock rom before flashing cm11, one right after i rooted my phone, and one after moving some folders and files to the external card.
2. after doing a wipe, i chose to restore the second backup, the one i made after moving files and folders, and it didn't quite work out - everything appeared to restore perfectly, but my device was immediately inundated with pop up warnings about stopped apps, i also got a persistent warning that the system had stopped responding as well, prompting me to choose between "wait" or "stop it". not only was the restored backup mired in popup screens, but it was impossibly slow, impossibly "laggy".
3. so i decided to restore the other stock backup, the one i made before i moved folders and files, and the results were the same, pop screens for apps not working, system warnings, severe lags, etc., identical to the first backup.
then i panicked.
1. i decided to flash my phone with the "[SGH-M919] CF-Auto-Root" file again, again with odin, hoping that it would put me where i started - i didn't stop to think that my phone was already rooted, that the file was was for unrooted phones.
2. not only did the reflash not work (my phone just booted as normal, as if the flash didn't get a chance to finish), but cwm recovery in boot mode was gone, replaced by what appears to be the andorid stock recovery screen, a screen with an animated dying/collapsing robot, - the screen was titled: "android system recovery <3e> and asked for an "update" from the external storage or cache.
3. not knowing what "update" it was looking for, i selected a backed system files (the first rooted stock rom backup i made, the second rooted stock backup i made, and even the cm11 file) - none worked.
4. i then downloaded a clean stock rom from cwm's website, converted it from zip to tar, and tried to flash it using odin with my device in upload mode, it didn't work either.
so how badly did i mess up my phone? any help would be greatly appreciated.
aeneas1 said:
so i recently dove into rooting my s4 after first spending a lot of time reading this great board, thought i had a handle on it, thought things were going very well, but i've hit a snag, which came while attempting my first restore - i'm hopeful someone will give me a little help,
a little background:
1. before rooting i backed up my phone with titanium, also backed it up by copying all of its contents to my pc.
2. i followed the excellent "[SGH-M919] CF-Auto-Root" instructions and it worked without a hitch, it was a quick and easy process, no surprises.
3. confirmed that i was rooted using "root checker", all systems were go.
4. once the root was done i made another backup using titanium and sms backup. i also made a full system backup using online nandroid pro and, to be extra safe, i also backed up efs using efs backup tool.
5. i then moved some folders and files to my external card and once again backed up my phone as before, including to my pc.
6. feeling confident that i could now restore my system to its rooted stock state if things went south, i decided to flash my first rom with cwm, i went with cm11 m7 4.4.3 - i saved the cm11 and gapps zips to my external card using rom tool box pro, rebooted into cwm recovery, selected the two files, and flashed. i also did a data and cache wipe before doing so.
6. needless to say i was thrilled when cm11 loaded perfectly, it worked great, and it was just what i was hoping for.
7. having been bitten by the apparent ease of flashing roms, i decided to restore my system to it's pre cm11 state, to it's rooted stock rom state, and try another rom, rather than just flash another rom from cm11 - i wanted to make sure that returning to my rooted stock rom state would be a simple matter.
and that's where i've run into problems.
1. as i mentioned i made two system backups of my stock rom before flashing cm11, one right after i rooted my phone, and one after moving some folders and files to the external card.
2. after doing a wipe, i chose to restore the second backup, the one i made after moving files and folders, and it didn't quite work out - everything appeared to restore perfectly, but my device was immediately inundated with pop up warnings about stopped apps, i also got a persistent warning that the system had stopped responding as well, prompting me to choose between "wait" or "stop it". not only was the restored backup mired in popup screens, but it was impossibly slow, impossibly "laggy".
3. so i decided to restore the other stock backup, the one i made before i moved folders and files, and the results were the same, pop screens for apps not working, system warnings, severe lags, etc., identical to the first backup.
then i panicked.
1. i decided to flash my phone with the "[SGH-M919] CF-Auto-Root" file again, again with odin, hoping that it would put me where i started - i didn't stop to think that my phone was already rooted, that the file was was for unrooted phones.
2. not only did the reflash not work (my phone just booted as normal, as if the flash didn't get a chance to finish), but cwm recovery in boot mode was gone, replaced by what appears to be the andorid stock recovery screen, a screen with an animated dying/collapsing robot, - the screen was titled: "android system recovery <3e> and asked for an "update" from the external storage or cache.
3. not knowing what "update" it was looking for, i selected a backed system files (the first rooted stock rom backup i made, the second rooted stock backup i made, and even the cm11 file) - none worked.
4. i then downloaded a clean stock rom from cwm's website, converted it from zip to tar, and tried to flash it using odin with my device in upload mode, it didn't work either.
so how badly did i mess up my phone? any help would be greatly appreciated.
Click to expand...
Click to collapse
If it boots at all you didn't kill it.
Not sure what rom you got from the CWM site. They do recoveries, not roms. The ROM manager app does allow you to download roms, but you can't just convert those from zip to tar. That doesn't make them flashable in Odin.
Here's what you do. Get the stock ROM from either here on XDA (use the search feature to find it) or from Sammobile.com.
Flash that in Odin.
Then you can start over.
---OR---
If you want to try to fix what you've got now, download CWM or TWRP RECOVERY (nor ROM) and flash that in Odin. Boot to recovery, wipe data and system, and flash any other rom you want. That will start you over with a fresh rom of your choice.
Skipjacks said:
f it boots at all you didn't kill it.
Click to expand...
Click to collapse
hallelujah!
Skipjacks said:
Not sure what rom you got from the CWM site. They do recoveries, not roms.
Click to expand...
Click to collapse
my apologies, i meant that i downloaded recovery files from the cwm website, not a rom files - i got them from https://www.clockworkmod.com/rommanager - i downloaded both (touch & non-touch) s4 t-mobile versions (6.0.4.7). i'm assumed those were recovery files?
Skipjack" said:
The ROM manager app does allow you to download roms, but you can't just convert those from zip to tar. That doesn't make them flashable in Odin.
Click to expand...
Click to collapse
again, my apologies - i meant that i downloaded *.img files, not zips, and converted them to tars for odin use. i used a batch file to convert them from img to tar, found at xda, here: http://forum.xda-developers.com/showthread.php?t=2281287 - it seemed to do the job, odin ran and reported success. wrong files? wrong conversion?
Skipjack said:
Here's what you do. Get the stock ROM from either here on XDA (use the search feature to find it) or from Sammobile.com.
Flash that in Odin.
Then you can start over.
---OR---
If you want to try to fix what you've got now, download CWM or TWRP RECOVERY (nor ROM) and flash that in Odin. Boot to recovery, wipe data and system, and flash any other rom you want. That will start you over with a fresh rom of your choice.
Click to expand...
Click to collapse
given a choice, i'd like to do what's bolded in red - but that's what i thought i was doing by flashing the cwm file i downloaded from the cwm website - but after the flash attempt it wouldn't boot into cwm, it would just boot into (i'm assuming") the stock rom i restored, which was a mess. i also unchecked auto-boot to see if that helped - but when i manually booted it didn't boot into cwm, it booted into the stock recovery, with the animated android.
i'll try downloading cwm from the sources you provided, and see if that does the trick. btw, why do you think i was able to flash the cm11 rom with (seemingly) perfect success, but wasn't able to restore either one of the full system (android) backups i made after i rooted my phone?
anyway Skipjack, thanks a ton for your assistance and i'll report back after i give your sources a try. fwiw, it sure is a great charge when a newbie like me sees a custom rom load for the first time, displaying a new ui as it boots, fun stuff.
Just download the ready yo flash tar files. Cwm has them. Twrp has them.
success Skipjack thanks to your generous time and assistance!
i ended up downloading the latest odin zip i could find and philz_touch_6.08.9-jfltetmo.tar.md5... my first try didn't take, with auto-reboot checked, my phone simply rebooted into the same problematic rom i had restored. i then tried it with auto-boot unchecked and manually booted when odin reported pass/success, and it worked. what struck me as odd was how long it took to flash, to report pass/success, around 3-5 minutes if i had to guess, a big difference compared to when i first used odin to root my phone with the["SGH-M919] CF-Auto-Root *.tar.md5 file - i'm guessing that's why it didn't work with auto-boot checked, just took too long?
anyway once i booted into philz_touch recovery i executed the wipe data/factory reset > clean to install a new rom command and then flashed the cm11 m7 (snapshot) rom, which i had flashed once before, right before i attempted to restore the stock rom it had replaced. and as was the case the first time around, it installed without a hitch and is running smooth and fast.
however now when i boot the phone, as soon as the cyanogen logo appears, very tiny text appears in the upper left hand corner which reads (i had to use a magnifying glass!) - it doesn't seem to effect the performance of he device but i'd like to get to the bottom of it, i've already searched and it appears to be a rather common issue.
kernel is not seandroid enforcing
set warranty bit: kernel
btw, i forgot to mention, when i purchased my sgh-m99 it already had 4.3 installed - when i flashed my first rom (cm11 m7) it included kitkat 4.4.2... could this be what caused my problems? did trying to go back to (restore) a 4.3 rom after flashing a 4.4.2 rom screw things up? can this even be done successfully?
and finally, at the risk of bugging the heck out of you, what roms do you prefer for your s4, assuming you have an s4? do you like aosp roms or touchwiz? does one type have a better reputation of being more stable? the primary reason i wanted to rot my phone was to get rid of a bunch of t-mobile / samsung bloatware, which i thought i could do by installing a lean custom rom. any suggestions, which are your favorites? thanks again Skipkack.
ouhned after
re the two lines of text i now get in the upper left hand corner of the screen whenever i boot, the kernel message:
kernel is not seandroid enforcing
set warranty bit: kernel
well after a lot of searching and reading, including coming across dozens of "fixes" and "solutions" that didn't seem to work for many folks, these two responses seemed to make some sense, what do you think?
eclpsues said:
I'm not an expert in Android OS but I think this is not an error. It is more of a notification that the STOCK KERNEL has been change to a CUSTOM one.
Click to expand...
Click to collapse
Joku1981 said:
You are right.
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=2594483
aeneas1 said:
re the two lines of text i now get in the upper left hand corner of the screen whenever i boot, the kernel message:
kernel is not seandroid enforcing
set warranty bit: kernel
well after a lot of searching and reading, including coming across dozens of "fixes" and "solutions" that didn't seem to work for many folks, these two responses seemed to make some sense, what do you think?
http://forum.xda-developers.com/showthread.php?t=2594483
Click to expand...
Click to collapse
The tiny text on the boot screen is basically telling you that Knox has been tripped. You are right. It does not affect the performance of the phone.
Skipjacks said:
The tiny text on the boot screen is basically telling you that Knox has been tripped. You are right. It does not affect the performance of the phone.
Click to expand...
Click to collapse
thanks skipjack... btw i'm really liking the cm11 m7 rom but, via the learning curve process, i've discovered it does not support wifi calling, something that apparently all aosp rom lack, guess i'll have to go with a touchwiz rom even tho the selection seems to be few and far between. also, is it possible to revert back to 4.3 once 4.4.2 has been flashed? seems like there's a lot of mixed opinions on this, altho in terms of those opinions it's hard for me tell who the pros are that should believed, and who the other guys are that really don't know. thanks again.
aeneas1 said:
thanks skipjack... btw i'm really liking the cm11 m7 rom but, via the learning curve process, i've discovered it does not support wifi calling, something that apparently all aosp rom lack, guess i'll have to go with a touchwiz rom even tho the selection seems to be few and far between. also, is it possible to revert back to 4.3 once 4.4.2 has been flashed? seems like there's a lot of mixed opinions on this, altho in terms of those opinions it's hard for me tell who the pros are that should believed, and who the other guys are that really don't know. thanks again.
Click to expand...
Click to collapse
Once you are rooted you can flash any custom ROM 4.3, 4.4, 4.2, etc. and then go back to stock 4.3. And only TW ROMs allow wifi calling
Sent from my SGH-M919 using XDA Premium 4 mobile app
Kriptik210 said:
Once you are rooted you can flash any custom ROM 4.3, 4.4, 4.2, etc. and then go back to stock 4.3. And only TW ROMs allow wifi calling.
Click to expand...
Click to collapse
very interesting... i guess i misunderstood the posts i read on the subject, maybe they were discussing whether or not you could revert to 4.3 from 4.4.2 on non-rooted phones, which i'm guessing isn't possible. anyway, as i mentioned previously, i fist rooted my 4.3 phone, did a full system backup (using online nandroid), flashed a 4.4.2 rom which worked perfectly, then tried to restore my 4.3 backup only to encounter a bunch of problems, thought going from 4.4.2 back to 4.3 may have caused the problems but i guess not?
so if i'm using a 4.4.2 custom rom and want to restore a 4.3 backup i should be able to boot into recovery and restore from there? or would i need to do a 4.3 flash first, before restoring a 4.3 backup?
aeneas1 said:
very interesting... i guess i misunderstood the posts i read on the subject, maybe they were discussing whether or not you could revert to 4.3 from 4.4.2 on non-rooted phones, which i'm guessing isn't possible. anyway, as i mentioned previously, i fist rooted my 4.3 phone, did a full system backup (using online nandroid), flashed a 4.4.2 rom which worked perfectly, then tried to restore my 4.3 backup only to encounter a bunch of problems, thought going from 4.4.2 back to 4.3 may have caused the problems but i guess not?
Click to expand...
Click to collapse
Did you wipe before you restored? And do not misunderstand this, you cannot downgrade firmwares once you go 4.3 and up, but you can downgrade the system, which is what you did with your backup
serio22 said:
Did you wipe before you restored? And do not misunderstand this, you cannot downgrade firmwares once you go 4.3 and up, but you can downgrade the system, which is what you did with your backup
Click to expand...
Click to collapse
thanks very much for the clarification, i was under the impression that firmware and system were somewhat synonymous in this context, i.e. if you upgraded firmware you were in effect upgrading the system, but i see that's not the case, again thanks. and yes i did do a full wipe before trying to restore the backup, was i not supposed to?
aeneas1 said:
thanks very much for the clarification, i was under the impression that firmware and system were somewhat synonymous in this context, i.e. if you upgraded firmware you were in effect upgrading the system, but i see that's not the case, again thanks. and yes i did do a full wipe before trying to restore the backup, was i not supposed to?
Click to expand...
Click to collapse
Updating firmware does update the system. Based on your previous comment the only thing you did was update the system by flashing a ROM which only contains the system, data, and kernel, so you can still flash the 4.3 firmware. Firmware consists of bootloader, recovery, modem, and system, what you cannot downgrade is the bootloader, the flash will fail every time because it will try to downgrade it. And you should not experience any issues restoring your back up. What were this problems?
btw serio22, do you have a favorite tw rom?
Yea serio22, what is your favorite TW ROM?
Sent from my SGH-M919 using XDA Premium 4 mobile app
serio22 said:
Based on your previous comment the only thing you did was update the system by flashing a ROM which only contains the system, data, and kernel, so you can still flash the 4.3 firmware.
Click to expand...
Click to collapse
but the cm11 rom zip i flashed included 4.4.2, before flashing i was using 4.3 - so didn't i update (or change) both the system and firmware?
btw, fwiw, - now that i'm up and running thanks to skipjacks help, i decided to try restoring my 4.3 backup again. when i tried this in the past it would restore to the same state as it was before but it was virtually unusable because of severe lags and multiple app not working popups that made navigating almost impossible. well now when i try to restore it fails and i get the following message:
checking md summs...
md5 mismatch
serio22 said:
Based on your previous comment the only thing you did was update the system by flashing a ROM which only contains the system, data, and kernel, so you can still flash the 4.3 firmware.
Click to expand...
Click to collapse
but the cm11 rom zip i flashed included 4.4.2, before flashing i was using 4.3 - so didn't i update (or change) both the system and firmware?
btw, fwiw, - now that i'm up and running thanks to skipjacks help, i decided to try restoring my 4.3 backup again. as i mentioned, when i tried this in the past it would restore to the same state as it was before but it was virtually unusable because of severe lags and multiple "app not working" popups that made navigating almost impossible. but now when i try to restore the 4.3 backup it fails and i get the following message:
checking md summs...
md5 mismatch
update:
well it looks like the *.md5 file was pointing to my internal drive rather than external which is where i had moved the 4.3 backup (and apparently the *.md5 file didn't update or account for the move), anyway i copied the backup to my internal drive and, viola, no more md5 mismatch errors. more importantly, it restored the 4.3 backup perfectly, in the exact same state as before, without all of lagging and pop up issues i was having before, so i'm one happy camper! not sure what i did the first time around, but all is good now, for he time being, sure wish i knew what i mucked up to cause the problems in the first place, i really have no idea, other than being a newbie at this. also, fwiw, the tiny text in the upper left hand corner that appears during boot (kernal message) no longer appears now that i have restored the 4.3 system backup... fwiw2, i'm liking the philz_touch_recovery but it sure has taken some getting used to, the commands are so close together and the thing is so sensitive, very easy to accidentally select the wrong option, and some of the wrong options aren't too friendly if it wasn't what you had intended to select.
aeneas1 said:
but the cm11 rom zip i flashed included 4.4.2, before flashing i was using 4.3 - so didn't i update (or change) both the system and firmware?
Click to expand...
Click to collapse
Read my previous post more closely below. Good to see you up and running though! And no I don't have a favorite tw Rom
serio22 said:
Updating firmware does update the system. Based on your previous comment the only thing you did was update the system by flashing a ROM which only contains the system, data, and kernel, so you can still flash the 4.3 firmware. Firmware consists of bootloader, recovery, modem, and system, what you cannot downgrade is the bootloader, the flash will fail every time because it will try to downgrade it.
Click to expand...
Click to collapse

[Q] Multiple problems after flashing Stock

Hello everyone,
After a long fight to try and get this phone back to normal, everything seemed good,
except not really
I started on a buggy CM11 version. Sick of it, I downloaded a 4.4.4 stock rom. I had to disable firewall and defender, but I got Odin to flash my md5. I got through everything and it booted successfully. After signing in and all that jazz, I find out that my WiFi isn't working. After a few reboots, My 4G finally works and everything seems to be steady.
Then, after exploring the rest of the phone I find out that all my apps from last ROM are still there. I know that you are supposed to wipe before flashing, but I was told that Odin will take care of that. It obviously didn't.
After THAT, I try to boot into Recovery as the next sensible step is to try to wipe my data and cache. I turn the phone off and press (Vol up + Home + Pwr) and the first boot screen shows for a moment. It says in blue "RECOVERY BOOTING" in the corner. Right after, it disappears and in another second it does the same screen without the "RECOVERY BOOTING". And as presumed, it does a regular boot.
What did I miss? How can I wipe my phone from recovery? How can I fix my problem with Wifi?
Reflash in Odin.
Make sure you have the correct stock rom. If you flash the "md5" you may have flashed the wrong thing. The md5 is not tge firmware, that is just the code that verifies your firmware file is not corrupted.
If your old apps were still there, you flashed the wrong thing. There is no way to flash stock firmware in odin and not wipe the data partition.
You are correct then
Yeah, I flashed a tar.md5 in Odin. It gave me a new ROM but all my apps are there. After all that, I still can't go to recovery. I tried using the terminal and ROM Toolbox to go there, both didn't work. Can I just leave it as it is and find a way to recovery or is the only way to go to bootloader and flash a correct file to get to recovery?
Flash twrp and see if it will reboot into recovery, then factory reset and flash latest firmware with Odin right after. Odin will NOT wipe data. It has to be done manually
serio22 said:
Flash twrp and see if it will reboot into recovery, then factory reset and flash latest firmware with Odin right after. Odin will NOT wipe data. It has to be done manually
Click to expand...
Click to collapse
It depends on what you ate flashing.
If you are flashing a full stock factory image it will wipe user data. If you are just flashing a system partition it won't.
Essem G said:
Hello everyone,
After a long fight to try and get this phone back to normal, everything seemed good,
except not really
I started on a buggy CM11 version. Sick of it, I downloaded a 4.4.4 stock rom. I had to disable firewall and defender, but I got Odin to flash my md5. I got through everything and it booted successfully. After signing in and all that jazz, I find out that my WiFi isn't working. After a few reboots, My 4G finally works and everything seems to be steady.
Then, after exploring the rest of the phone I find out that all my apps from last ROM are still there. I know that you are supposed to wipe before flashing, but I was told that Odin will take care of that. It obviously didn't.
After THAT, I try to boot into Recovery as the next sensible step is to try to wipe my data and cache. I turn the phone off and press (Vol up + Home + Pwr) and the first boot screen shows for a moment. It says in blue "RECOVERY BOOTING" in the corner. Right after, it disappears and in another second it does the same screen without the "RECOVERY BOOTING". And as presumed, it does a regular boot.
What did I miss? How can I wipe my phone from recovery? How can I fix my problem with Wifi?
Click to expand...
Click to collapse
Fkash twrp and format system, data, cache and preload and install a deodexed stock os
g7755725 said:
Fkash twrp and format system, data, cache and preload and install a deodexed stock os
Click to expand...
Click to collapse
Also this. This gives you more control over the whole process
Skipjacks said:
Also this. This gives you more control over the whole process
Click to expand...
Click to collapse
How do I know whatever I download is deodexed? And I went to a page of ROMs someone gave me and I downloaded the NK2 version, which also gave me a tar.md5. If I want the correct thing to flash, what should I flash?
Essem G said:
How do I know whatever I download is deodexed? And I went to a page of ROMs someone gave me and I downloaded the NK2 version, which also gave me a tar.md5. If I want the correct thing to flash, what should I flash?
Click to expand...
Click to collapse
The first post of any customized stock rom will tell you if its deodexed. If it doesn't say it...its not.
@Essem G:
Any updates for us? I'm following this thread because I have similar problems with my WiFi not working after upgrading from 4.2.2.
Any luck getting TWRP flashed?
Also I believe that the stock firmwares do come as tar.md5's, as in the file: M919UVUFNK2_M919TMBFNK2_M919UVUFNK2_HOME.tar.md5 from ShinySide's stock firmware thread.
As for the WiFi issue, from the hours of reading I've done it looks like this problem occurs when you upgrade your firmware, but it no longer matches the bootloader. Such as bootloader (Baseband) showing MDL, but Build Number showing NH7, NK2, etc. What does your show?
This thread may be of use to you when you get back to a working ROM. Good luck!
@RavenMind1
Everyone has been saying different answers and i've put off fixing my device for a while. I'm just afraid i'll brick it forever and have another nightmare after this current one. So no, there has been no progress. I think i'm gonna try to flash Philz and format my system, then flash a deodexed rom. @g7755725 said that you can flash TWRP, but I usually use Philz. It appears to be that I have lost root access because no root features work and SuperSU won't recognize it. Will everything work or am I setting my self up for disaster?
Edit: Where can I find a deodexed rom? I desperately need one, thanks
Essem G said:
@RavenMind1
Everyone has been saying different answers and i've put off fixing my device for a while. I'm just afraid i'll brick it forever and have another nightmare after this current one. So no, there has been no progress. I think i'm gonna try to flash Philz and format my system, then flash a deodexed rom. @g7755725 said that you can flash TWRP, but I usually use Philz. It appears to be that I have lost root access because no root features work and SuperSU won't recognize it. Will everything work or am I setting my self up for disaster?
Edit: Where can I find a deodexed rom? I desperately need one, thanks
Click to expand...
Click to collapse
Look in the forums for deodexed rom theirs a bunch and untouched as well i had philz but it eoukdnt boot my s4 so i had to switch to twrp because it does better then any recovery
g7755725 said:
Look in the forums for deodexed rom theirs a bunch and untouched as well i had philz but it eoukdnt boot my s4 so i had to switch to twrp because it does better then any recovery
Click to expand...
Click to collapse
Thanks for the support so far, but has this problem occured before? do you think the steps i've listed will solve this? Im just trying to make sure that I know exactly what to do before I go in. Thanks
Essem G said:
Thanks for the support so far, but has this problem occured before? do you think the steps i've listed will solve this? Im just trying to make sure that I know exactly what to do before I go in. Thanks[/Q] it should
Click to expand...
Click to collapse
@g7755725 I downloaded a deodexed rom from the SkipJacks guy (different page than what you sent me) and it's a little under 9MB... how could this possibly be a ROM?
Essem G said:
@g7755725 I downloaded a deodexed rom from the SkipJacks guy (different page than what you sent me) and it's a little under 9MB... how could this possibly be a ROM?
Click to expand...
Click to collapse
Have you tried my gamerrom Ultimate 1 its basically stock touchwiz of if Official NK2 M919UVUFNK2 with stweaks and no bloatware here is the thread gru 1 is in.the botyom of the thread http://forum.xda-developers.com/galaxy-s4-tmobile/development/stock-os-gamerrom-ultimate-2-touchwiz-t3078467
Sounds cool but i would have been interested a few months ago. I'm trying to sell the phone so I need to get it back to stock. Appreciate all the help and I think it's cool that you make ROMs
Essem G said:
Sounds cool but i would have been interested a few months ago. I'm trying to sell the phone so I need to get it back to stock. Appreciate all the help and I think it's cool that you make ROMs
Click to expand...
Click to collapse
If you're trying to go back to complete stock then just Odin NK2 firmware. http://forum.xda-developers.com/galaxy-s4-tmobile/general/firmwares-official-mdl-mk2-nb4-t2816508 I used the NK2 from here about 2 days ago to go back to stock.

Categories

Resources