Related
Initial instructions can be found here. but i will detail them out further.
Disclamer: these files are meant specifically for the Samsung Galaxy Discover(SCH-R740C). Use on any other device will result in an instant brick of device. Use these files at your peril, you assume any responsibility for loss or damage that may result from use of these files or procedures.
You have been warned.
now to the goodies.....
List of supplies:
1. Phone (SCH-R740C)
2. USB cord that syncs with the PC
3. USB drivers installed for the phone
4. Files from this location. click here
HOW TO UPDATE DEVICE FROM 4.0.4 TO 4.1.2
easiest method is to use simple upgrade tool from here or here under downloads then software.
the simple upgrade tool will update the device if like mine, the OTA method failed.
ROOTING
NOTE:this method only works for devices already running 4.1.2. for rooting 4.0.4, use kingoroot which can be found here
before starting, please make sure you have "UPDATE-SuperSU.zip" copied to the root of your external SD card which you can download from here
+++to install CWM:
Follow these steps very carefully, or you might brick your phone.
1. Download Odin package and CWM-recovery-amazing3gcri-eng.tar.md5 from here Extract Odin to a known location and copy the tar.md5 files to the same location
2. Right click on the .exe file inside of the odin folder and select “Run as Administrator”
3. Now that odin is running:
4. Place you galaxy discover in download mode:
4a. With phone off hold vol - and power button
4b. Wait for the phone to present it warning menu release vol - and power
4c. press Vol +
5. CLICK ON THE PDA BUTTON
6. Browse to the appropriate sub directory and select "CWM-recovery-amazing3gcri-eng.tar.md5"
7. Press Start.
DO NOT DISCONNECT, UNPLUG, PLAY WITH ANY BUTTONS, OR CLICK ANYTHING ON EITHER THE PHONE OR COMPUTER UNTIL ODIN HAS FINISHED FLASHING CLOCKWORK RECOVERY ON YOUR PHONE.
8. To boot into recovery, turn off the phone, now press and hold the volume up button, press and hold the power button, wait for phone to boot to recovery, release both buttons. ignore the triangle at the bottom of the screen, that will get fixed later
9. Now highlight "Install ZIP". select "choose from sdcard"
10. Scroll to "UPDATE-SuperSU.zip", and select using power button. another menu will pop up with "- - Yes Install UPDATE-SuperSU-v1.94.zip" use power button to select it.
11. Wait for the magic.....
12. Once it is done, go ahead and pull battery and reboot device.
+++At this point, your device if the steps above have been followed to a T, should be fully functional(rooted) and running 4.1.2.
TO INSTALL NEAR-STOCK DEODEXED 4.1.2
1. Download "deodexednearstock4.1.2SCH-R740C.zip" from here. and put it onto the root of your external SD card.
2.reboot phone into CWM recovery
3.(recommended but can be skipped if on 4.1.2)once in recovery, use the volume keys to highlight wipe data/factory reset. use the power button to select it.
3a. use volume keys again to highlight " Yes - Wipe all user data". and use the power button to select it. wait until it is done
4.highlight "Install ZIP. select "choose from sdcard"
5. scroll to "deodexednearstock4.1.2SCH-R740C.zip", and select using power button. another menu will pop up with "- - Yes Install deodexednearstock4.1.2SCH-R740C.zip" use power button to select it.
6. wait for the magic.....
7. once it is done, go ahead and pull battery and reboot device. it may take about up to 10 minutes or so to get into the device itself to get it set back up.
+++at this point you should be on stock(except for launcher and browser) deodexed 4.1.2
just a word of warning, you'll have to install a web browser into it. when i first installed NakedRom from it's original form, it did not come with one. And to get Google Voice Search to work, just let it update from the Play Market.
TO REMOVE TRIANGLE ON BOOT
1. Go into download mode again (volume down + power and then volume up)
2. Plug in the phone.
3 Open Odin and select PDA and open "stock_recovery.tar.md5"
4. Make sure phone recognizes, and hit start.
4a. Again, same as last time, do not touch device until it says complete.
5. When it's done, pull battery and reboot device.
+++At this point the triangle should have gone away but just to make sure.....
6. download and install triangle away from chainfire. here's the link
7. follow these instructions here. it's a youtube video about an S3 but the way you work the application should be really close to what's shown. run the application and let it do it's thing.
now device is completely stock (except the ADW launcher and root)
credits/ kudos; thanks to cowboyenvy for providing the initial tutorial.
chainfire for his wonderful softwares. and the gentleman who ported NakedRom to this device (to which this is all based off of).
just a word of warning, you'll have to install a web browser into it. when i first installed NakedRom from it's original form, it did not come with one. And to get google voice search to work, just let it update from the market.
the rom is fully deodexed so you should see a little bit of a speed improvement.
please feel free to let me know if there's any issues with this release and i will fix them as they are found for now as this device is the one i primarily use as of right now.
REriginal post
will have files in their respective locations in less than 20 minute from this post
schizoidd said:
will have files in their respective locations in less than 20 minute from this post
Click to expand...
Click to collapse
ignore this quote. everything's ready
no longer developing on....
I am no longer Deving on this device. I have a HTC Desire 510 now that I have been working on an will release things for it as needed
But I will be keeping links alive until cricket stops CDMA support in July of this year
warnings
just an FYI, maxing out the processor speed not only greatly reduces battery life of the device but also shortens the usable life of the device even after changing the battery
by the end of my device's life, it was only good for making calls, surfing the internet, sending texts, etc. but I couldn't play even the simplest of games (like 2048) without my device freezing
SAMSUNG GALAXY NOTE 2
SOLUTION/FIXING/RESOLUTION/RECOVERY TO BOOTLOOP/ERROR: CAN’T WRITE TO PARTITION/ODIN FAILUREDownload following files:
1. PC Odin latest version.
2. .PIT file for Your Device Version (GT N7100/7105 etc.)
3. Stock firmware of your choice.
4. Samsung Kies.
Procedure:
1. Install Samsung KIES on your PC.
2. Run Odin on your PC.
3. Remove memory and sim card (if available) from your device reinstall battery.
4. Reboot your device to download mode for this PRESS AND HOLD VOL DOWN+POWER+HOME BUTTONS SIMULTANEOUSLY that will display warning (do not fear) now press VOL DOWN AGAIN.
5. Connect your device to PC.
6. On ODIN window, click on AP and browse downloaded stock firmware (will take a minute to load). Then Click on PIT and browse downloaded “.PIT” file for your device specifically. And check/tick “Full NAND Erase”. DO NOT CHANGE (CHECK OR UNCHECK) ANY OTHER OPTIONS ON ODIN
7. Click on start and sit back leaving device, PC and cables untouched.
8. After completion of flashing your will reboot automatically. Now disconnect your device from PC.
9. If it gets stuck on boot logo then pull out battery and reinstall. Then go to recovery mode (BY PRESSING VOL UP+ POWER+HOME AT THE SAME TIME) and clean cache.
10. Then Reboot your device and enjoy.
DISCLAIMER: IT HELPED ME AND MANY MORE BUT AT THE SAME THIS INFORMATION MAY NOT HELP EVERYONE SO RESPONOSIBILITY FOR BRICKING/DAMAGING/LOOSING YOUR DEVICE ENTIRELY LIES ON YOU.
Hi friends today I am going to tell you how to root note3neo lollipop stock rom. Plz follow all steps. I have successfully rooted without any problem but I have heard that some are loosing their imei. So make a backup as soon as you are in twrp. Now the process as follows.
Do it at your own risk.
First Download the below file. It contains all the files including the USB drivers.
Link -: https://mega.nz/#!C99gxYDR!wkIse-u4wfCKIn-p3iH-6QSjtZ74p8Zom82-uRjqdcY
Now follow the steps below.
Installation
1.)Turn on usb debugging in developer option.
Tap the Settings option.
Tap the About Phone option.
Keep tapping the Build Number option (seven times) until it says you are a developer.
Tap the new Developer Options menu that appears.
Make sure that the USB Debugging option is checked.
2.)Power off your device, press and hold Volume Down + Home + Power buttons at the same time until you see a Warning with a Yellow Triangle.
3.)Now press Volume Up button. Your phone now is in ODIN MODE (Download Mode).
4.)Open Odin on PC. ( Odin is available in the link zip file )
5.)UNTICK everything
6.)Connect Phone to PC using USB Cable.(You will see added message on Odin)
7.)On Odin click on PDA(till version 3.07) OR click on AP(after version 3.09)
8.)Select the twrp.tar.md5
9.)Press on start.
10.)Remove battery quickly after Odin says pass before it boots up.
11.)Insert battery again. Press Power + Volume Up + Home button, and hold till you see the Samsung logo.
12. Next it will boot into twrp. Now first I suggest you to make a backup.
13. Now flash the SuperSU.zip file which I have provided in the zip.
Done. Your mobile is now rooted.
. Please Thank me If Helped
Now this is for the people who want xposed.
Download the file below and extract it.
https://mega.nz/#!uw8hRJQL!lnFobDr36EzNZhH15ibnIejnn9TsIIkYGDMPCOilfnA
You will find 2 file. One of apk and other is of zip.
Install the apk file. Next reboot to recovery and flash the 2nd file which is of zip.
Reboot will take some time.
Done
thanx bro
THIS MIGHT WORK FOR YOUR DEVICE BUT IF ANY DAMAGE IS DONE TO YOUR DEVICE I AM NOT RESPONSIBLE! AND THIS WILL ONLY WORK ON A10. [SM-A105, SM-A107 AND MORE]
1. You need to install the exact firmware for your model onto your PC. [I recommend a website called updato or install samware and get the firmware there.]
2. Install Odin 3.14.1. If you already have it go to the next step.
3. Unlock your bootloader. If you have done this please go to the next step but if not please go to 3.a
3a. !UNLOCKING YOUR BOOTLOADER WILL FACTORY RESET YOUR DEVICE! - Go to settings and go to about phone, then tap the build number until a message comes on the bottom of the screen saying "You are now a developer!" or something close to that. Go to developer settings by going back to the settings menu and scrolling all the way down to see it. After going to developer options turn on "OEM Unlocking" and tap allow. Also just in case turn on USB Debugging. After that turn off your device. After your phone is turned off press "Volume Up"+ "Volume Down" and plug in a USB from your PC simultaneously, you should see a splash screen with a warning. Hold "Volume Up" for until 7 seconds or less and you should see another warning to confirm you want to unlock the bootloader. Press "Volume Up". You will get a warning when you boot up the phone, just press "Power".
4. After the phone booted up, do the normal setup. Then go to Chrome and download Magisk Manager.
5. Then, go to your pc, and locate the firmware you have downloaded and copy the AP tar file onto your phone.
6. Open magisk manager, tap install, and tap "Select and Patch a File".
7. Select the AP tar file you copied from your PC and wait for the process to be done.
8. You should see a new file called "magisk_patched.tar" and transfer the file to your PC.
9. Open Odin on your PC, and turn off your device and turn it on using "Volume Up", "Volume Down" and USB combination.
10. You should see the same warning sign. Just press "Volume Up" once. Do not hold it just press it once.
11. Your PC will make a sound alerting you that the phone has connected.
12. On the BL section on Odin, open your firmware location and select the file with BL in front of it.
13. On the AP section on Odin, open the "magisk_patched.tar" file you had transferred from the phone.
14. On the CP section on Odin, open your firmware location and select the file with CP in front of it.
15. On the CSC section on Odin, open your firmware location and select the file with CSC in front of it.
16. On Odin, look for a section called Options on the left-hand side. Click options, and turn off auto restart.
17. Click start and wait for the process to finish.
18. After the process is finished, please take the USB out.
19. !!THIS IS THE HARD PART!! - You need to hold down "Volume Down" and "Power". After the screen goes black immediately hold "Volume Up" and "Power". This will direct you to the stock recovery of the phone.
20. If the recovery says, "NO SYSTEM FOUND", don't worry as for then your phone is not A/B partitioned and that's okay and you will need to skip 21 for now and select Reboot System and do the normal setup. But if you can see options in the recovery, please use the "Volume keys" to scroll and "Power" to select. Select Wipe Data and confirm.
21. After the erasing process, just let the phone boot up, and do the setup.
22. Install Magisk Manager if your phone hasn't already downloaded it.
23. !!!FOR THE NON A/B PARTITIONED IF YOU ARE A/B PARTITIONED THEN PLEASE GO TO THE NEXT STEP!!! If you boot up normally - (System without magisk)
Booting up with "Volume Up" and "Power" - (System with magisk)
24. Enjoy Magisk!
If you have any questions please comment them down below!
Thanks to Topjohnwu for creating the method and MAKING magisk.
Downaroo said:
THIS MIGHT WORK FOR YOUR DEVICE BUT IF ANY DAMAGE IS DONE TO YOUR DEVICE I AM NOT RESPONSIBLE! AND THIS WILL ONLY WORK ON A10 ONLY [SM-A105xx].
1. You need to install the exact firmware for your model onto your PC. [I recommend a website called updato or install samware and get the firmware there.]
2. Install Odin 3.14.1. If you already have it go to the next step.
3. Unlock your bootloader. If you have done this please go to the next step but if not please go to 3.a
3a. !UNLOCKING YOUR BOOTLOADER WILL FACTORY RESET YOUR DEVICE! - Go to settings and go to about phone, then tap the build number until a message comes on the bottom of the screen saying "You are now a developer!" or something close to that. Go to developer settings by going back to the settings menu and scrolling all the way down to see it. After going to developer options turn on "OEM Unlocking" and tap allow. Also just in case turn on USB Debugging. After that turn off your device. After your phone is turned off press "Volume Up"+ "Volume Down" and plug in a USB from your PC simultaneously, you should see a splash screen with a warning. Hold "Volume Up" for until 7 seconds or less and you should see another warning to confirm you want to unlock the bootloader. Press "Volume Up". You will get a warning when you boot up the phone, just press "Power".
4. After the phone booted up, do the normal setup. Then go to Chrome and download Magisk Manager.
5. Then, go to your pc, and locate the firmware you have downloaded and copy the AP tar file onto your phone.
6. Open magisk manager, tap install, and tap "Select and Patch a File".
7. Select the AP tar file you copied from your PC and wait for the process to be done.
8. You should see a new file called "magisk_patched.tar" and transfer the file to your PC.
9. Open Odin on your PC, and turn off your device and turn it on using "Volume Up", "Volume Down" and USB combination.
10. You should see the same warning sign. Just press "Volume Up" once. Do not hold it just press it once.
11. Your PC will make a sound alerting you that the phone has connected.
12. On the BL section on Odin, open your firmware location and select the file with BL in front of it.
13. On the AP section on Odin, open the "magisk_patched.tar" file you had transferred from the phone.
14. On the CP section on Odin, open your firmware location and select the file with CP in front of it.
15. On the CSC section on Odin, open your firmware location and select the file with CSC in front of it.
16. On Odin, look for a section called Options on the left-hand side. Click options, and turn off auto restart.
17. Click start and wait for the process to finish.
18. After the process is finished, please take the USB out.
19. !!THIS IS THE HARD PART!! - You need to hold down "Volume Down" and "Power". After the screen goes black immediately hold "Volume Up" and "Power". This will direct you to the stock recovery of the phone.
20. If the recovery says, "NO SYSTEM FOUND", don't worry as for then your phone is not A/B partitioned and that's okay and you will need to skip 21 for now and select Reboot System and do the normal setup. But if you can see options in the recovery, please use the "Volume keys" to scroll and "Power" to select. Select Wipe Data and confirm.
21. After the erasing process, just let the phone boot up, and do the setup.
22. Install Magisk Manager if your phone hasn't already downloaded it.
23. !!!FOR THE NON A/B PARTITIONED IF YOU ARE A/B PARTITIONED THEN PLEASE GO TO THE NEXT STEP!!! If you boot up normally - (System without magisk)
Booting up with "Volume Up" and "Power" - (System with magisk)
24. Enjoy Magisk!
If you have any questions please comment them down below!
Click to expand...
Click to collapse
What about Samsung Galaxy A10s can you tell me please
Ragheb Aloqab said:
What about Samsung Galaxy A10s can you tell me please
Click to expand...
Click to collapse
I am sure you can, but before trying this method please take a full backup
works for a105m bit 5?
daniromerohn said:
works for a105m bit 5?
Click to expand...
Click to collapse
should work, but keep a backup just incase
Downaroo said:
THIS MIGHT WORK FOR YOUR DEVICE BUT IF ANY DAMAGE IS DONE TO YOUR DEVICE I AM NOT RESPONSIBLE! AND THIS WILL ONLY WORK ON A10. [SM-A105, SM-A107 AND MORE]
1. You need to install the exact firmware for your model onto your PC. [I recommend a website called updato or install samware and get the firmware there.]
2. Install Odin 3.14.1. If you already have it go to the next step.
3. Unlock your bootloader. If you have done this please go to the next step but if not please go to 3.a
3a. !UNLOCKING YOUR BOOTLOADER WILL FACTORY RESET YOUR DEVICE! - Go to settings and go to about phone, then tap the build number until a message comes on the bottom of the screen saying "You are now a developer!" or something close to that. Go to developer settings by going back to the settings menu and scrolling all the way down to see it. After going to developer options turn on "OEM Unlocking" and tap allow. Also just in case turn on USB Debugging. After that turn off your device. After your phone is turned off press "Volume Up"+ "Volume Down" and plug in a USB from your PC simultaneously, you should see a splash screen with a warning. Hold "Volume Up" for until 7 seconds or less and you should see another warning to confirm you want to unlock the bootloader. Press "Volume Up". You will get a warning when you boot up the phone, just press "Power".
4. After the phone booted up, do the normal setup. Then go to Chrome and download Magisk Manager.
5. Then, go to your pc, and locate the firmware you have downloaded and copy the AP tar file onto your phone.
6. Open magisk manager, tap install, and tap "Select and Patch a File".
7. Select the AP tar file you copied from your PC and wait for the process to be done.
8. You should see a new file called "magisk_patched.tar" and transfer the file to your PC.
9. Open Odin on your PC, and turn off your device and turn it on using "Volume Up", "Volume Down" and USB combination.
10. You should see the same warning sign. Just press "Volume Up" once. Do not hold it just press it once.
11. Your PC will make a sound alerting you that the phone has connected.
12. On the BL section on Odin, open your firmware location and select the file with BL in front of it.
13. On the AP section on Odin, open the "magisk_patched.tar" file you had transferred from the phone.
14. On the CP section on Odin, open your firmware location and select the file with CP in front of it.
15. On the CSC section on Odin, open your firmware location and select the file with CSC in front of it.
16. On Odin, look for a section called Options on the left-hand side. Click options, and turn off auto restart.
17. Click start and wait for the process to finish.
18. After the process is finished, please take the USB out.
19. !!THIS IS THE HARD PART!! - You need to hold down "Volume Down" and "Power". After the screen goes black immediately hold "Volume Up" and "Power". This will direct you to the stock recovery of the phone.
20. If the recovery says, "NO SYSTEM FOUND", don't worry as for then your phone is not A/B partitioned and that's okay and you will need to skip 21 for now and select Reboot System and do the normal setup. But if you can see options in the recovery, please use the "Volume keys" to scroll and "Power" to select. Select Wipe Data and confirm.
21. After the erasing process, just let the phone boot up, and do the setup.
22. Install Magisk Manager if your phone hasn't already downloaded it.
23. !!!FOR THE NON A/B PARTITIONED IF YOU ARE A/B PARTITIONED THEN PLEASE GO TO THE NEXT STEP!!! If you boot up normally - (System without magisk)
Booting up with "Volume Up" and "Power" - (System with magisk)
24. Enjoy Magisk!
If you have any questions please comment them down below!
Thanks to Topjohnwu for creating the method and MAKING magisk.
Click to expand...
Click to collapse
Does this work on the SM-A102U? Or is there any custom recovery for it?
Tyreethetruth said:
Does this work on the SM-A102U? Or is there any custom recovery for it?
Click to expand...
Click to collapse
Should work with any Samsung galaxy a10, so if it works, enjoy!
Odin keeps crashing when it is nearly complete
I have done this yet however it crashes when I follow your steps with a text box like "Odin Downloader has stop working". I have even gone to the extent where I have turned the magisk_patched.tar into a .tar.md5 file and still the same old error. How do I fix it?
If you require more info, I have a sm-a105fn/ds running android 9. Whenever it is on the "userdata" stage in odin, it crashes. I am using Odin 3 v3.13.1
error in boot and go back to download mode
Not working
I tried and once the flashing was done it rebooted to Download Mode instead and says "error verifying vbmeta image ok_not_signed (3)"
Bad Thread..
My older thread is way mor organized, and doesnt have the 16gb issue that you have... you just copied afanehs thread and made it look bad..
cmz6996 said:
Bad Thread..
My older thread is way mor organized, and doesnt have the 16gb issue that you have... you just copied afanehs thread and made it look bad..
Click to expand...
Click to collapse
I'm sorry, I wasn't copying as I thought of it myself but you're right it has the same steps as afanehs thread. Your thread is more organized and mine doesn't fix the 16gb issue that i had. I'm sorry for the inconvenience
Downaroo said:
I'm sorry, I wasn't copying as I thought of it myself but you're right it has the same steps as afanehs thread. Your thread is more organized and mine doesn't fix the 16gb issue that i had. I'm sorry for the inconvenience
Click to expand...
Click to collapse
No worries, I was abit rough, but try and fix it up. GL In the future!
What to do if it is stuck in recovery in odin. Help me please
.
I have a samsung galaxy a10e sm-a102u and I don't have oem unlocking as an option. Please help
TWRP v3.5.0 for Samsung Galaxy A50. I JUST UPGRADED IT to v3.5.0 based on TWRP v3.4.0 One UI 2.5 BTL1 firmware by mohitmallick17
Tested install GSI and Custom rom FreshROMs by TenSeventy7 ( recommended custom rom to try ). Tested rooting SM-A505F BTL1 firmware. Please tell us if it works for other models.
Flash TWRP Instructions:
Make sure the bootloader are unlocked, OEM unlock option is grey out
Enter Download Mode : Turn Power Off. Press and hold Volume Up + Volume Down key together, while pressing these keys, connect the phone to computer, then press volume up once.
Open ODIN, IMPORTANT!: Uncheck “Auto Reboot” in Options!
Flashing TWRP_v3.5.0_A505_BTL1_Magisk.tar as AP in ODIN, then click start.
Magisk is now successfully flashed to your device! Several steps before you can properly use the device.
DO NOT SKIP THIS STEP! Press and hold Volume Down + Power Key, when the screen blank quickly press and hold Volume Up + Power key, when Samsung Logo appears release Power key only, keep pressing Volume Up key until TWRP Recovery Mode Appears.
Select Wipe -> Format data, type 'yes' and confirm
Select Install - select multidisabler-samsung-2.6.zip Swipe to confirm Flash
Select Reboot to System
When SAMSUNG logo appears wait for a few minutes or more then press and hold volume down + power key until the screen blank
Setup the phone
Rooting if necessary
First time Restart or Power off, make sure the OEM unlocking options is grey out
Enter TWRP recovery : Turn Power Off. Press and hold Volume Up key + Power Key, When SAMSUNG logo appears release Power Key only, keep pressing Volume Up key until TWRP recovery appears.
Select Reboot to - Recovery
Install Magisk Manager
Connect to Internet
Open Magisk Manager, it will ask to do additional setups. Let it do its job and the app will automatically reboot your device.
Done!
DOWNLOAD
Download TWRP_v3.5.0_A505_BTL1.tar, use this if you want to install TWRP only
Download TWRP_v3.5.0_A505_BTL1_Magisk.tar, use this if you want to root - Magisk v21.2 patched
Credit to mohitmallick17
Nice job
this will work with BTK5 fw?
I managed to root Successfully but after additional setup the phone rebooted after 5 secs, it was on but still asked for additional setup, suddenly after updating from Magisk v8.0.5 to Magisk v22 I lost root now I tried to boot device it failed to turn on but now in download mode with error VBmeta: No sign info
Bros! are this supposed to work on SM-A505Fn? cuz i tried it and soft bricked my phone -_-
PetiHun08 said:
Bros! are this supposed to work on SM-A505Fn? cuz i tried it and soft bricked my phone -_-
Click to expand...
Click to collapse
UPDAAAATE. Reflashed everytrhing tried again and works on btl3+ sm-a505fn/ds eu model
shoosterjonesr said:
I managed to root Successfully but after additional setup the phone rebooted after 5 secs, it was on but still asked for additional setup, suddenly after updating from Magisk v8.0.5 to Magisk v22 I lost root now I tried to boot device it failed to turn on but now in download mode with error VBmeta: No sign info
Click to expand...
Click to collapse
U need to flash multidisaabler
Will this work on an A50 witn the Android 11/ OneUI 3.1 update? Because I got nothing but errors and bootloops trying to root that, while I had no problems with an Android 10 version.
IF i dont have an sd card can i sideload
redymedan said:
TWRP v3.5.0 for Samsung Galaxy A50. I JUST UPGRADED IT to v3.5.0 based on TWRP v3.4.0 One UI 2.5 BTL1 firmware by mohitmallick17
Tested install GSI and Custom rom FreshROMs by TenSeventy7 ( recommended custom rom to try ). Tested rooting SM-A505F BTL1 firmware. Please tell us if it works for other models.
Flash TWRP Instructions:
Make sure the bootloader are unlocked, OEM unlock option is grey out
Enter Download Mode : Turn Power Off. Press and hold Volume Up + Volume Down key together, while pressing these keys, connect the phone to computer, then press volume up once.
Open ODIN, IMPORTANT!: Uncheck “Auto Reboot” in Options!
Flashing TWRP_v3.5.0_A505_BTL1_Magisk.tar as AP in ODIN, then click start.
Magisk is now successfully flashed to your device! Several steps before you can properly use the device.
DO NOT SKIP THIS STEP! Press and hold Volume Down + Power Key, when the screen blank quickly press and hold Volume Up + Power key, when Samsung Logo appears release Power key only, keep pressing Volume Up key until TWRP Recovery Mode Appears.
Select Wipe -> Format data, type 'yes' and confirm
Select Install - select multidisabler-samsung-2.6.zip Swipe to confirm Flash
Select Reboot to System
When SAMSUNG logo appears wait for a few minutes or more then press and hold volume down + power key until the screen blank
Setup the phone
Rooting if necessary
First time Restart or Power off, make sure the OEM unlocking options is grey out
Enter TWRP recovery : Turn Power Off. Press and hold Volume Up key + Power Key, When SAMSUNG logo appears release Power Key only, keep pressing Volume Up key until TWRP recovery appears.
Select Reboot to - Recovery
Install Magisk Manager
Connect to Internet
Open Magisk Manager, it will ask to do additional setups. Let it do its job and the app will automatically reboot your device.
Done!
DOWNLOAD
Download TWRP_v3.5.0_A505_BTL1.tar, use this if you want to install TWRP only
Download TWRP_v3.5.0_A505_BTL1_Magisk.tar, use this if you want to root - Magisk v21.ifpatched
Credit to mohitmallick17
Click to expand...
Click to collapse
if i have no sdcard can i sideload multidisabler?
PetiHun08 said:
IF i dont have an sd card can i sideload
if i have no sdcard can i sideload multidisabler?
Click to expand...
Click to collapse
after format data just copy multidisabler to internal storage
Ok with mtp obviously. Thank u
redymedan said:
TWRP v3.5.0 for Samsung Galaxy A50. I JUST UPGRADED IT to v3.5.0 based on TWRP v3.4.0 One UI 2.5 BTL1 firmware by mohitmallick17
Tested install GSI and Custom rom FreshROMs by TenSeventy7 ( recommended custom rom to try ). Tested rooting SM-A505F BTL1 firmware. Please tell us if it works for other models.
Flash TWRP Instructions:
Make sure the bootloader are unlocked, OEM unlock option is grey out
Enter Download Mode : Turn Power Off. Press and hold Volume Up + Volume Down key together, while pressing these keys, connect the phone to computer, then press volume up once.
Open ODIN, IMPORTANT!: Uncheck “Auto Reboot” in Options!
Flashing TWRP_v3.5.0_A505_BTL1_Magisk.tar as AP in ODIN, then click start.
Magisk is now successfully flashed to your device! Several steps before you can properly use the device.
DO NOT SKIP THIS STEP! Press and hold Volume Down + Power Key, when the screen blank quickly press and hold Volume Up + Power key, when Samsung Logo appears release Power key only, keep pressing Volume Up key until TWRP Recovery Mode Appears.
Select Wipe -> Format data, type 'yes' and confirm
Select Install - select multidisabler-samsung-2.6.zip Swipe to confirm Flash
Select Reboot to System
When SAMSUNG logo appears wait for a few minutes or more then press and hold volume down + power key until the screen blank
Setup the phone
Rooting if necessary
First time Restart or Power off, make sure the OEM unlocking options is grey out
Enter TWRP recovery : Turn Power Off. Press and hold Volume Up key + Power Key, When SAMSUNG logo appears release Power Key only, keep pressing Volume Up key until TWRP recovery appears.
Select Reboot to - Recovery
Install Magisk Manager
Connect to Internet
Open Magisk Manager, it will ask to do additional setups. Let it do its job and the app will automatically reboot your device.
Done!
DOWNLOAD
Download TWRP_v3.5.0_A505_BTL1.tar, use this if you want to install TWRP only
Download TWRP_v3.5.0_A505_BTL1_Magisk.tar, use this if you want to root - Magisk v21.2 patched
Credit to mohitmallick17
Click to expand...
Click to collapse
Hmm... Another a505fn but ds model. Im stuck on boootloader warning. Can somebody help? (i flashed multidisabler and rebooted to system
PetiHun08 said:
Hmm... Another a505fn but ds model. Im stuck on boootloader warning. Can somebody help? (i flashed multidisabler and rebooted to system
Click to expand...
Click to collapse
Got back to stock rom. Plz help
PetiHun08 said:
Got back to stock rom. Plz help
Click to expand...
Click to collapse
I think boot.img isthe problem. Maybe can i fiish if i flash twrp with no magsk?(btw my phone has no ramdisk)
Still waitin
Will this work for A50s FN ?
Right now it is flashed with TWRP 3.3.0, but I want to upgrade to Android 11 and is looking for suitable TWRP upgrade. It's my main phone so I can't risk have it bootloop
Hi,I unlocked bootloader,but canot install Twrp.in odin,it always failed.Help ?
What error
PetiHun08 said:
What error
Click to expand...
Click to collapse
In odin it faild,I realise,I'm on exynis version,but cenot finde exynos version of twrp.
I have exynos a50 and mine is forking fine. Ehat error do odin gives you?