Related
A bit of caution when picking out screen protectors
I had to cut the edges on my AT&T screen protectors due to the nature of the soft back which when pressure is applied to the front causes lifting on the screen protector's 4 corners. The dimensions are fine but the radius is too small for the corners causing them to protrude ... just cut them a little but I would have preferred to have 100% perfect screen protectors instead of half assed ones from AT&T ... why am I not surprised.
sentinel79 said:
A bit of caution when picking out screen protectors
I had to cut the edges on my AT&T screen protectors due to the nature of the soft back which when pressure is applied to the front causes lifting on the screen protector's 4 corners. The dimensions are fine but the radius is too small for the corners causing them to protrude ... just cut them a little but I would have preferred to have 100% perfect screen protectors instead of half assed ones from AT&T ... why am I not surprised.
Click to expand...
Click to collapse
I purchased the same protector. I have the same issue as well. Makes it look really cheap with the corners sticking up.
I had that, plus since I am opening mine a LOT for hacking, the bottom looks like crap.
Looks like I am going to replace the protector within a week of getting the phone.
Just wrap the whole phone in plastic wrap with the back off. Then slip it on.
Bad idea most likely, but it would be funny if it worked well.
same issue. Trimmed the corners. It doesn't look that great, but doesn't peel up when i hit the corner on something. I'm on the third protector already. First one i screwed up the orientation and got dust under it when fixing. second peeled up when i hit one of the corners.
must be those poor quality screen protector. there us not much of an option atm. i would rather get a HTC HD mini screen protector and punch a hole on it.
I just had Ghost Armor put on my iPhone 3G (which I'm handing to my daughter when my Aria comes in). It's pretty nice, but the Aria isn't showing up on their website yet. And you would only really want to get the screen done, since you open up the phone to get to the battery and the SD Card.
Yep, I cut them carefully and used the scotch tape method to get perfect placement.
-------------------------------------
Sent via the XDA Tapatalk App
sentinel79 said:
Yep, I cut them carefully and used the scotch tape method to get perfect placement.
-------------------------------------
Sent via the XDA Tapatalk App
Click to expand...
Click to collapse
Can you elaborate on the "scotch tape method"?
I ordered invisible gadget guard from amazon. Havent put it on yet, but that packaging sure makes it look impressive.
Before separating the films I placed tape to use as handles to apply the protector flat (instead of holding it).
Then after layed down on the screen pulled up and slid tape underneath to attract any particles which cause bubbles. Slide with sticky side face up so it pulls from the protector's sticky film (rarely do the particles stick to the screen itself).
Sent from my HTC Liberty using XDA App
Has anybody noticed the quality of these are not that great?
Have had on for 3 days. There are a LOT of scratches on the protector itself. I usually keep phone in jean pockets with a wallet.
Anybody plan on trying the Amzer ones, although I have heard their quality may be dubious too for the n1.
Shad0wguy said:
I ordered invisible gadget guard from amazon. Havent put it on yet, but that packaging sure makes it look impressive.
Click to expand...
Click to collapse
I ordered this, and it shipped today. I got my 8 GB card in the mail today, too. I kind of wished I had gotten a 16 GB card, since my whole music collection is about 8 GB. But I may pick up another 8 GB as my "backup film roll" at a later time.
Donatron said:
I purchased the same protector. I have the same issue as well. Makes it look really cheap with the corners sticking up.
Click to expand...
Click to collapse
I can't believe I didn't figure out this solution earlier. Obviously, trimming the excess on the corners would solve the issue, but I wasn't comfortable using a razor blade to make the trims. But just 5 minutes ago, it occurred to me to use a nail clipper (while already installed on the phone, and the back plate removed). Worked perfectly, was super easy, and did no damage to the phone.
Yeah that didnt occur to me either. I used small crafting scissors.
Sent from my HTC Liberty using XDA App
Same thing happened to me, just on the bottom corners though, but as soon as I put my case on it covered up those bubbles, cant even see it. Quality of the protector seems to be decent. I used a universal one prior and it was ****!
I ordered the stealth guard though for the phone (full body protection) just now so when that comes I'll let you guys know how that works out as well.
I used the Invisible Gadget Guard that someone else mentioned (got it off ebay though, not amazon, it's the exact same one however). The quality of it is definitely top notch, I've had it on for a little over a month now and it has no scratches/marks that are visible without actually looking for them and even then there are minimal and very minor ones. My one complaint with it is the top two corners did start to peel a bit, I ended up peeling it up a tad and cutting them (with difficulty, this thing is tough!) and reapplying that part and I haven't had a problem since! I do have a few blemishes down the left side due to my clumsiness during the initial applicaton, but the case covers it for the most part
i tried the invisisheild and did not like the rubbery feel, got at t sheild it is a hard plastic and fingers slide much better, yes i had to trim but no big deal there. all you have to do is put the protector on the phone with back cover off, then take a new sharp razor blade at about 50 degree angle to the edge of glass and trim excess off. 3 months now and have not lifted any corners. these are much better than the rubber vinly covers that tend to stretch and need trimming as well.
Okay, I know that everyone wants to protect their beautiful new phone's screen but every screen protector I have come across is such a ***** to put on.
Any recommendations on which are the best and HOW TO INSTALL them the easiest?
I hate bubbles!
Follow me on Twitter
@ShtISeeOnCampus
A chronicle of peculiar things I see on my college campus.
checkthisSH said:
Okay, I know that everyone wants to protect their beautiful new phone's screen but every screen protector I have come across is such a ***** to put on.
Any recommendations on which are the best and HOW TO INSTALL them the easiest?
I hate bubbles!
Follow me on Twitter
@ShtISeeOnCampus
A chronicle of peculiar things I see on my college campus.
Click to expand...
Click to collapse
Dude, I'm pretty sure there is already a thread on this a few posts below... personally, I find eBay has the cheapest, and as long as you're careful in your application, they work great. I got one that reduces glare and doesn't collect fingerprints like the screen used to. They also have privacy screens, mirror screens, and more. Just depends on how much you pay. If you really have to have a perfect application of the screen and have the money, then get a screen protector at one of those little mall kiosks, where they are usually more than happy to put it on for you, the right way. It just tends to cost more than buying online.
Sent from my HTC Glacier using XDA App
You've got to make sure that your screen is absolutely clean and dustless. If there's dust, a bubble will form around the dust particle and no amount of pushing will get rid of the bubble. I use a lint free wipe (the kind sold for cleaning glasses or computer screens) as well as a piece of microfiber cloth to dry the screen off. Then I blow the screen clean with canned air. I make sure my hands are washed and I don't touch the screen protector directly. I find that even if I hold the screen protector by the edge only, I'll leave at least one speck of dust. Instead, I put a piece of scotch tape on the upper surface of the screen protector and use that as a handle to manipulate the protector while I install it.
I've also had luck carefully lifting off the protector with scotch tape and then sticking the corner of a lint free wipe in, sandwiched between the screen and the protector, to pull out that one last dust particle.
Hope this helps. Good luck.
Thanks guys.
I've ruined two so far. Haha.
Got dust all over the adhesive side.
They are probably unsalvageable now aren't they?
You can save them...use clear packing tape and secure it to a table sticky side up.
Take your screen protector that has the dust (the side that sticks to the screen) face down on the sticky take. Keep a hold of the screen protector by using scotch tape or similar...push down and just pull up...and repeat until the protector is clean and reapply to your phone.
Sent from my HTC Glacier using XDA App
Vinsane said:
You can save them...use clear packing tape and secure it to a table sticky side up.
Take your screen protector that has the dust (the side that sticks to the screen) face down on the sticky take. Keep a hold of the screen protector by using scotch tape or similar...push down and just pull up...and repeat until the protector is clean and reapply to your phone.
Sent from my HTC Glacier using XDA App
Click to expand...
Click to collapse
Thats a great idea! Will this also remove finger prints?
I made the mistake of grabbing the sticky side out of frustration and put a nice smudge on it.
Yes it sure will. It will totally clean it off. The only thing that method can't fix are creases or bends.
This way, it'll save you from having to buy more screen protectors since those are still pretty new.
Sent from my HTC Glacier using XDA App
really doesn't matter what type of screen protector it is... I've always found that, Glass Cleaner, blow dryer, and a credit card always work best. Make sure your screen is clean, hold your phone about half of an arms length away, spray the cleaner so there's a light mist of it on the phones screen. Place the screen protector, and the cleaner should give you a bit of play before it's set, get where you want it, use the credit card to remove any air bubbles, and the blow dryer will help dry what little cleaner is left behind the screen protector... Hope this helps
DaMyth said:
really doesn't matter what type of screen protector it is... I've always found that, Glass Cleaner, blow dryer, and a credit card always work best. Make sure your screen is clean, hold your phone about half of an arms length away, spray the cleaner so there's a light mist of it on the phones screen. Place the screen protector, and the cleaner should give you a bit of play before it's set, get where you want it, use the credit card to remove any air bubbles, and the blow dryer will help dry what little cleaner is left behind the screen protector... Hope this helps
Click to expand...
Click to collapse
The glass cleaner won't damage the phone if left under the screen protector?
Wow there is so much I have never thought of!
Haha, thanks guys.
I have had good luck with the real look brand
Sent from my HTC Glacier using XDA App
I've had my Realook on late November. It's still in excellent condition. I occasionally use scotch tape on one corner to lift it up and remove what little dust collects around the edges.
Another trick I know of is to apply the SP in the bathroom after running the shower on hot for a few minutes. It gets a lot of moisture in the air and causes dust to settle for a bit. Combine that with an impeccably clean screen, careful application (with latex or nitrile gloves if you got some), and a good squeegee and you'll be tip-top.
best out there
Dude you can't beat the Zagg protectors plus the lifetime warranty and if you drop it and your ish breaks they buy you a new one.
BRANDENDEUCE said:
Dude you can't beat the Zagg protectors plus the lifetime warranty and if you drop it and your ish breaks they buy you a new one.
Click to expand...
Click to collapse
They provide a warranty on your actual device?
check out the site zagg.com
For those of you with the realook protector, are you having any problems with the proximity sensor on the phone? There's reviews on amazon stating that the realook covers the entire front face of the phone (including the little proximity sensor in the top left). Apparently, this makes it impossible for the phone to tell when it's up to your ear during calls, and subsequently the screen stays dark no matter what you do. Can anyone else confirm this issue, and does your realook screen protector cover just the rectangular lcd screen, or the entire front glass face of the phone?
checkthisSH said:
They provide a warranty on your actual device?
Click to expand...
Click to collapse
no, but they do provide a lifetime warranty on your invisibleshield...if anything happens, you send it back and they'll send you a new one free of charge
I love my invisible shields and i put one on every device I won
iPad, Macbook Pro, MYT4G, my iphone 4, my HD7...everything lol
Jottle said:
There's reviews on amazon stating that the realook covers the entire front face of the phone (including the little proximity sensor in the top left).
Click to expand...
Click to collapse
the invisibleshield has a cutout for the sensor, not sure about the realook one
Jottle said:
For those of you with the realook protector, are you having any problems with the proximity sensor on the phone? There's reviews on amazon stating that the realook covers the entire front face of the phone (including the little proximity sensor in the top left). Apparently, this makes it impossible for the phone to tell when it's up to your ear during calls, and subsequently the screen stays dark no matter what you do. Can anyone else confirm this issue, and does your realook screen protector cover just the rectangular lcd screen, or the entire front glass face of the phone?
Click to expand...
Click to collapse
I have no cut out for the sensors and it covers the entire glass. I've never had problems with the proximity sensor.
However, I do remember reading that they changed their template and that the newer version isn't as good. Might want to look into that before buying.
yeah with ZAGG, you pay a premium, but it also contains the pieces to cover the back and sides of the phone. This + the tmobile clear hard shell case is quite the combo to a protected phone
ive found the screen protectors from BestSkinEver are literally the bestever! haha...but seriously, they are amazing and feel like a soft gel when it completely dries and you'll hafto wait till it completely dries to see how amazing the skin looks. if done carefully (the site provides detailed instructions - water and a tiny bit of soap is needed), you'll have the clearest skin you could want! good luck!
i can't post the url link (since im still a newb) so google bestskinever
I use the xtreme guard protectors off eBay(kinda expensive $4 for just one) but its perfect for me. Absolutely no air bubbles.
Sent from my HTC Glacier using XDA App
I read that the gap between the bezel and the glass is to help with the glass expanding due to heat, but it seems to collect dust a lot and its driving me nuts. Anyone know of a way to prevent this or a slim case that covers the gap so dust does not get in there?
i don't see a problem with my phone, mostly because the case is hiding it all LOL
and even when i do take out the case, i don't see dirt collecting there
i just go blow it off easily with a gasp of air with my mouth
Mine too!!! Have 2 white specs in top left side and don't wanna stick something in there and scratch it... Annoying thing is that my d30 case covers everything up but that little damn corner where the power button is... Ugh
Sent from my SGH-T989 using Tapatalk
I just noticed this dust accumulating in there today. Hrm.
just puff it every now and then to prevent excess accumulation and prevent it from turning into dirt
this is between the bezel and glass .. so not under the glass right? this is a huge problem with my nexus one and don't want another phone where i have to deal with it
I use the body glove case from tmobile when I'm at work. My work enviroment is extremely dirty and very dusty. I mean to the point where you clean the area and by the end of the day there is a pretty thick layer of flux (lets just say dust) everywhere.
When I take my case off on the weekend my bezel is clean
dime079 said:
this is between the bezel and glass .. so not under the glass right? this is a huge problem with my nexus one and don't want another phone where i have to deal with it
Click to expand...
Click to collapse
The SAMOLED screens are fused to the class so there is no gap for dust to collect.
To get rid of the dust I use a stiff lens cloth damp with lens fluid and use a corner to clean. Works perfectly
Sent from my SGH-T989 using xda premium
dime079 said:
this is between the bezel and glass .. so not under the glass right? this is a huge problem with my nexus one and don't want another phone where i have to deal with it
Click to expand...
Click to collapse
dust between the bezel/screen common problem with any phone that has gap between the bezel and screen. like one person said, the digitizer is fused with the actual screen on Super Amoled screens. so dust shouldn't get underneath. However, screen repair cost more due to the fact the whole screen+digitizer has to be replaced instead of one or the other.
to get the dust out,I usually just take a very thin paper,fold it in half,and slide it. I've been doing the same method on my past phones.
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
I use painters tape after I clean the screen (before applying of course) to make sure no other dust or hairs are on the screen. Use a can of air to blow away crap in your work area also.
Sent from my Galaxy Nexus using xda premium
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Kobe_No_Means_No said:
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Click to expand...
Click to collapse
Will this work with SGP Ultra Crystal screen protector? or are they only the non-water applyable?
Can't speak specifically for the sgp but I've been using the wet application method on all my dry application protectors for some time across at least 5 different phone models with no issues. Much easier to apply accurately than dry
Sent from my SGH-T889 using Tapatalk 2
degeneration said:
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
Click to expand...
Click to collapse
I read some where that you should apply it in a bathroom and before you start get a spray bottle and put water in it. A couple sprays in the air before... No dust works for me
Sent from my SGH-T889 using XDA Premium
Well I just got 2 more cheap protectors in the mail, the first one I tried to get perfect, and each time I tried to get rid of a piece of dust it would get worse. The second one I have one bubble and I gave up. Fine. I have a bubble... oh, and they are cheapo reflectors, and supposed to be matte... so now my screen looks pretty horrible. Sigh. Whatever, my screen is protected. I will get an SGP later and figure something out in the mean time... maybe take them to a tmo store since they did it for me last time and it came out perfect somehow. I think my house is just too dusty, and there's no way to change that. I live in the desert, I have cats, the place is old. Sigh.
omg just did both of the note 2's and it took about 30-40 minutes, ridiculous, but afterwards looks nice till today i had the damn T-Mobile protector on it lol i got tired of seeing T-Mobile =P
Here's the trick for me. I got in the bathroom turn on the shower for a good few minutes. (Hot water) because the humidity in the air will get rid of most of the dust. Then you apply your screen protector by 1st.
Positioning it first without taking off the adhesive side (to know where the edges should be)
2nd.
You must not use a credit card to squegee out bubbles that'll scratch the screen, if you are put a microfiber cloth over the credit card so you'll be pushing down with the cloth not the card
Sent From the Van Down by the River
phreshjoker said:
Here's the trick for me. I got in the bathroom turn on the shower for a good few minutes. (Hot water) because the humidity in the air will get rid of most of the dust. Then you apply your screen protector by 1st.
Positioning it first without taking off the adhesive side (to know where the edges should be)
2nd.
You must not use a credit card to squegee out bubbles that'll scratch the screen, if you are put a microfiber cloth over the credit card so you'll be pushing down with the cloth not the card
Sent From the Van Down by the River
Click to expand...
Click to collapse
Well i did it at my dining table and i regretted doing so because I ended up getting a few particles underneath, but all you need to do at that point is take any type of sticker (mine came with 2 stickers which were called Dust Removal stickers, but its truly a regular sticker lol) so I had to use that several times, but the final result is great
I ended up ordering the SGP Ultra Crystal and also ordered MobC from amazon (http://www.amazon.com/gp/product/B009M7TZYO/ref=oh_details_o00_s00_i00) which ended up coming in first, so I am still waiting for the SGP but honestly i do regret ordering them because the MobC are freakin great, crystal clear, and i have no regrets of putting it on!
Kobe_No_Means_No said:
I'm really really good at applying screen protectors (wet application) because I started using Invisible Shield when they first came out about 10 years ago.
The trick is to not use their solution, as they only give you like a tiny vial of solution.
1. Get a plastic cup (I use one of those red beer-pong cups), fill it with warm water to the top, put 2 drops of dish detergent in, swirl your finger in it. That is your solution.
2. Remove the protector from the backing, dip the entire thing into the cup, place it on your screen. You should be able to easily move the protector around the screen to adjust positioning. If you cant, take it off, dip the whole thing in the solution again, and put it on the screen again. Yes, your device will get very wet, but do not worry... it's not a problem at all (I've done this to tons, and I mean tons, of phones/cameras/gps, etc...) Don't worry.
3. Once you're happy with the positioning, use a credit card to squeegee out the water in between. Adjust positioning again to make sure it's perfect, squeegee again. Squeegee a few more times, make sure you've gotten as much water out as possible. If your device has rounded corners (such as the back of the note 2 cover), after you squeegee out all the water the corner will still stick up. Put your finger on each corner for a few seconds, maybe 20-30 seconds if necessary. It will stick.
4. Done. It will be invisible, you will not notice a thing on your phone.
Click to expand...
Click to collapse
degeneration said:
So, screen sizes getting bigger seems to be making it more and more difficult to apply a screen protector without getting any stray cat hairs or dust in between it and the screen. How do you guys do it, or do you just put up with a bit of dust?
I just got a wet application screen protector today since that was the last kind of protector I successfully applied to a phone (long ago), but that was a no go. It seemed fine until I was done and realized that somehow, from some where, a bunch of hairs got under the protector. I tried to use some tape to get them off but it didn't work, and then I dropped the protector and things just got worse from there.
This was in the bathroom after taking a steamy shower as I have read over and over that it's supposed to get most of the crap out of the air.
How do you guys do it? I have looked it up several times, but I just don't get how these people have such an easy time of it.
Click to expand...
Click to collapse
For with app screen protectors...exactly as Kobe mentioned. Couple of drops / 1 part dish washing liquid to 5 parts water (distilled water if your tap water has too much minerals)...just so the solution is slippery enough for the application process. Run your finger nail down the edge of the credit card / tool your going to use to ensure there are no nicks / sharp edges that will damage / crease your wet app screen protector.
Steamed bathroom also helps.
I recommend dry applications for flat surface...wet applications for curved surfaces.
With dry app screen protectors, those clear / ultra clear packs off of eBay usually work well. The only issues I have seen is that the adhesive may get weak over time (if you need to lift protector to remove dust then press down again) and initial cutouts maybe hard to see from pics. Eventually these dry app screen protectors fall to 3/5/? packs per <$1 ???
Position the dry app screen protector then apply / remove film. There will probably be dust, pet hair, etc. Lift up one corner / side / section at a time and slide the shipping tape between the screen protector and screen (sticky side of shipping tape against sticky side of screen protector)...then press dry screen protector down on the shipping tape which will also press against the screen. Carefully lift the corner / section of the screen protector...then flip the shipping tape over and slide back under between the screen protector and screen (sticky side of shipping tape now facing screen) if needed. Usually the particle is on the sticky screen protector side, but sometimes it maybe stuck to the screen side. The idea is to use a shipping tape with strong enough adhesive to remove the particle without ripping off / damaging the screen protector adhesive. Painting tape adhesive maybe too weak in removing any dust / pet hairs...UPS grade shipping tape maybe too strong...I like Staples equivalent shipping / packing tape...it has just enough adhesive strength to remove any dust / pet hairs.
Hope some of this helps.
What works for me:
http://forum.xda-developers.com/showthread.php?t=1988725
Got my spigen... I am probably never buying from anyone else. Well, I dunno, but from the packaging to the application I felt like I was using quality. I thought I had ordered the ultra crystal but I actually went for ultra oleophobic for some reason... and I am crossing my fingers that the surface tension changes after some use (doubt it) but it does do what it says, finger prints do not stick. However the down side is the s pen doesn't feel nice against it (it did feel really nice against the crappy matte protector, felt like a pencil on paper, but I couldn't stand the rainbow effect, maybe I will try a spigen matte in the future). Any way, I used the "hinge" technique I saw somewhere online and it worked pretty well. Got 3 pieces of dust under the screen (1 on the screen, 2 on the bezel) and I used some scotch tape to life the protector and one of the included dust removal stickers to quickly take care of the problems.
the protector is FREAKING INVISIBLE! right now the screen is off and I can see reflections, and I can barely make out where the protector ends.
Thanks for everyone who gave me their tips and tricks, I finally have a screen protector on my note that I am happy with.
Also, for those people going naked, it doesn't affect my screen but I saw I already have 2 minute scratches on my screen. I keep my phone in my pocket on its own, and somehow I managed to scratch the screen already (got on release day). I have wasted a bunch of cash getting a screen protector on that I was happy with, and I might spend more in the future, but at least I know that if anything terrible happens I can replace the little piece of plastic instead of forever having to deal with a scratch.
EDIT: playing around with it some and then wiping it off, I already am fine with how the S pen feels. I think it was actually sticking to whatever they used to apply the outer layer of protection that you remove after applying the protector. A little bit more drag then on the naked glass, but I like that I can now get more of a tactile response of my writing. I am hooked on Spigen.
I do all my screen protectors at the dinning room table in about 2 mins with perfect results every time. I attached a few screenies but they really don't do it justice. It is insanely hard to get a good picture of something clear when using a flash. the specks of dust that are noticable are on top of the protector not underneath. I'm using the spigen oleophobic and love them.
I just installed 3 amFilm Glass Protectors with black borders. Yes, I can vouch for this protector.
Pros:
- Truly edge to edge, with a tiny gap at the edges for case-friendliness
- Does not block any part of the OLED
- Clear, practically looks like a naked screen
- Smooth (wifey said: feels so smooth!)
- Fingerprint-resistant
- Black borders means no visible edges
Cons:
- Can't really think of any. I used Vivid NG gesture app and have to turn increase "Touch Sensitivity" on display settings. No biggie.
- Installation takes longer; more elbow grease to get the bubbles out.
Installation tips:
- Allow at least 15-30 minutes for a good result
- Don't follow the myth of hot shower! That's just a waste water. Seriously.
- Have a roll of masking tape. Use it to clean the screen and sides of phone. Do this by sticking the tape vertically top to bottom starting on the left edge, then peel and move slightly to the right. Repeat until all screen and sides have been 'stripped' of dust specks.
- After placing the protector on the phone, start looking for any remaining specks. Do this by gently squeeging around. Bubbles will move and can be taken care of later. Specks will stay, so you want to spot and remove them now.
- To remove a speck (most likely it would stick to the film and not the screen), fold a length of masking tape in two, so both sides are sticky, then gently lift the closest corner and slide the masking tape underneath. Careful, do not let the masking tape rub the sticky side of the glass film such that it would leave a mark. Once on the right spot, press the film down gently and re-lift it. The speck will stick to the masking tape. Slide out the masking tape and let the film drop down.
- Repeat until all specks have been removed.
- Now squeegee the bubbles out. This takes a while on this screen protector, but you'll be happy with the result!
Ps: I don't use the provided dust stickers. Masking tape works better for me.
Attached are some photos after the installation on the second phone.
Got one of these on the way, hope it installs ok and works nicely with otterbox case. Mine is a work phone and they stipulate the otterbox must stay on. I hate the thing but the S10e is a nice phone.
This supposedly case friendly screen protector had so much potential....
Feel and fit is fantastic but it does NOT classify as case friendly. I cannot get air out of it with my case on. Awesome otherwise.
The case presses on the edges and distorts it, causing some lift.
I had my screen protector installed at a phone shop and the case somehow lifted the top part abit. Couldnt get the airbubble out no matter what so i tried using a hairdryer .. 15 seconds later no more airbubble.
Took mine off. Work insists the otterbox is used so if a screen protector doesn't work with it, too bad. There's no way it was going to fit under the edges of the case.
With a normal TPU type case it should be good though.
It's good enough a fit to even have a naked phone.