Hi, can some one respond to this? perhaps I bricked my Z doing:
I had rooted and S-OFF and I flashed PC10IMG_Vision_TMOUS_1.19.531.1_Radio_12.21.60.09b_26.02.01.15_M2_release_149459_signed.zip"
as I wanted to return to original stock rom. I did it from Goldcard SD card, what I prepared before. By doing this I lost root but remained S-OFF
Than I followed: http://forum.xda-developers.com/wiki/index.php?title=HTC_Vision#Unrooting_and_Returning_to_Stock go to S-ON and I managed this. Everything was going smooth so later when I was non root and S-ON, an OTA update came and I confirmed. Also next OTA update 2.3.3 T-mobile came with 73MB update and I confirmed too later. But the phone stucked after second update to 2.3.3 on HTC Logo and does not boot system.
- Hboot works
- recovery does not work (red attention mark)
- I have working fastboot and adb from PC
- phone is now S-ON and not rooted
... but not sure how to continue
tried flash new recovery but all fastboot end up like this:
Code:
$ fastboot flash recovery recovery-clockwork-3.0.2.4-vision.img
sending 'recovery' (4466 KB)...
OKAY [ 0.770s]
writing 'recovery'...
(bootloader) signature checking...
FAILED (remote: signature verify fail)
finished. total time: 1.261s
I can not flash another PC10IMG.zip as it says, no valid ID.
Really sucked here.
Anyone some good ideas or phone is postmortem?
You flashed a g2 rom on your dz?
I'd say grab the lastest rom from http://www.shipped-roms.com/index.php?category=android&model=Vision
and flash it via ruu mode (fastboot oem rebootRUU, fastboot flash zip nameOfZip.zip)
-Nipqer
Yes I did
I tried now as per your advise, but I have signature errors, tried two zips, same result.
Code:
$ fastboot flash zip Vision_TMOUS_1.12.531.0_Radio_12.18.60.05P_26.01.00.17_M2_144460.zip
sending 'zip' (118430 KB)...
OKAY [ 20.029s]
writing 'zip'...
(bootloader) signature checking...
FAILED (remote: 12 signature verify fail)
finished. total time: 33.034s
Any Ideas?
bump, anyone please?
Flashing any stock rom end up with signature error, the phone is branded to (INFOCID is T-MOB010)
no access to adb
INFOversion: 0.5
INFOversion-bootloader: 0.82.0000
INFOversion-baseband: 26.02.01.15_M2
INFOversion-cpld: None
INFOversion-microp: 0425
INFOversion-main: 1.19.531.1
INFOserialno: SH133RT00363
INFOimei: 352212047598680
INFOproduct: vision
INFOplatform: HBOOT-7230
INFOmodelid: PC1011000
INFOcidnum: T-MOB010
INFObattery-status: good
INFObattery-voltage: 3939mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: dirty-fafe9aa3
INFOhbootpreupdate: 11
INFOgencheckpt: 0
Try a different rom from shipped-roms.
the 1.19.531.1 rom or higher
-Nipqer
Nipqer said:
Try a different rom from shipped-roms.
the 1.19.531.1 rom or higher
-Nipqer
Click to expand...
Click to collapse
thanks. all images and I tried about 6 different including RRU I got from exe and gained from temp dir gives:
Code:
Image verification failed
HBOOT drops back to main menu, recovery says this error message.
any more hints?
Could you join the #G2ROOT irc channel on freenode It'll be easier to try help you there.
-Nipqer
Solved by creating GC by different method. Looks we did not have working GC before.
Can you be a bit more specific?
Sent from my HTC Vision using Tapatalk 2
i started my desire hd today and it got stuck on the splash screen and will not go any further, before i bin it i would like to try and get it going again. i ran adb and the result was this-
INFOversion: 0.5
INFOversion-bootloader: 2.00.0027
INFOversion-baseband: 26.14.04.28_M
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.12.405.1
INFOserialno: HT0ARRX03087
INFOimei: 352668040761130
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: HTC__001
INFObattery-status: low
INFObattery-voltage: 3550mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 743ca94a
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
i think i have found a stock rom that's compatible named- RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1_Radio_12.65.60.29_26.14.04.28_M_release_225512_signed
i can not install this via windows as the phone does not get to the bootloader on start up so i have copied the rom.zip to an sd card and renamed it PD98IMG.zip but the phone does not see it during HBOOT so i am wondering if the file is correct after all.
any help appreciated.
Ok simply run the RUU in Windows, Do not press next after you run it and then type into the run box (Windows Key + R) %temp% then when your in temp directory look for rom.zip once you have found it place some where like the root of c:.
After this boot the phone into Fastboot USB and then type fastboot oem rebootRUU this will reboot it into the right mode.
Then type fastboot flash zip c:\rom.zip
hope this helps.
hacktrix2006 said:
Ok simply run the RUU in Windows, Do not press next after you run it and then type into the run box (Windows Key + R) %temp% then when your in temp directory look for rom.zip once you have found it place some where like the root of c:.
After this boot the phone into Fastboot USB and then type fastboot oem rebootRUU this will reboot it into the right mode.
Then type fastboot flash zip c:\rom.zip
hope this helps.
Click to expand...
Click to collapse
just tried it and it failed, on reboot the phone just sat waiting, the only way to get the file to load was to go into fastboot usb and then i got an error message-
C:\>fastboot flash zip c:\rom.zip
< waiting for device >
sending 'zip' (336097 KB)... OKAY [ 58.150s]
writing 'zip'... INFOadopting the signature contained in this i
mage...
INFOsignature checking...
FAILED (remote: not allowed)
finished. total time: 114.910s
starting to think its a hardware fault rather than software.
doesn't look just confirm that you placed phone into fastboot oem rebootRUU mode which should of put a black screen with Silver HTC Logo?
just tried again, phone re boots but goes straight to a green htc on white background and stays there. adb reports it as ok
C:\>fastboot oem rebootRUU
... OKAY [ 0.166s]
finished. total time: 0.166s
Hi,
I need help with booting loop.
After trying to root and flash custom ROM I can't do anything.
I was using EasyAceRootTool to unlock a boot loader and to get Root access in custom ROM.
After going into recovery I wiped everything and installed cm-7-20130301-NIGHTLY-ace.zip without errors.
After rebooting I see only white screen.
I tried wipe and install again and again...was reading a lot of threads and did everything what I found. Still nothing.. (or I did in wrong way)
I've tried maybe 5 different RUU - all the time errors.
This is what I can see in fastboot:
**UNLOCKED**
ACE PVT SHIP S-ON RL
HBOOT-2.00.0029
MICROP-0438
RADIO-26.14.04.28_M
eMMC-boot
RECOVERY:
ClockworkMOD v5.8.1.5
in the bottom I can see:
E:Can't open / cache/recovery/log
E:Can't mount / cache/recovery/last_log
E:Can't open / cache/recovery/last_log
fastboot getvar all:
version: 0.5
version-bootloader: 2.00.0029
version-baseband: 26.14.04.28_M
version-cpld: None
version-microp: 0438
version-main: 3.13.0.0
serialno: MB141RX12271
imei: 356299047527468
product: ace
platform: HBOOT-7230
modelid: PD9810000
cidnum: HTC__001
battery-status: good
battery-voltage: 4199mV
partition-layout: Generic
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: fcef1579
hbootpreupdate: 11
gencheckpt: 0
region-id: 0
Thanks.
Gedaz said:
Hi,
I need help with booting loop.
After trying to root and flash custom ROM I can't do anything.
I was using EasyAceRootTool to unlock a boot loader and to get Root access in custom ROM.
After going into recovery I wiped everything and installed cm-7-20130301-NIGHTLY-ace.zip without errors.
After rebooting I see only white screen.
I tried wipe and install again and again...was reading a lot of threads and did everything what I found. Still nothing.. (or I did in wrong way)
I've tried maybe 5 different RUU - all the time errors.
This is what I can see in fastboot:
**UNLOCKED**
ACE PVT SHIP S-ON RL
HBOOT-2.00.0029
MICROP-0438
RADIO-26.14.04.28_M
eMMC-boot
RECOVERY:
ClockworkMOD v5.8.1.5
in the bottom I can see:
E:Can't open / cache/recovery/log
E:Can't mount / cache/recovery/last_log
E:Can't open / cache/recovery/last_log
fastboot getvar all:
version: 0.5
version-bootloader: 2.00.0029
version-baseband: 26.14.04.28_M
version-cpld: None
version-microp: 0438
version-main: 3.13.0.0
serialno: MB141RX12271
imei:
product: ace
platform: HBOOT-7230
modelid: PD9810000
cidnum: HTC__001
battery-status: good
battery-voltage: 4199mV
partition-layout: Generic
security: on
build-mode: SHIP
boot-mode: FASTBOOT
commitno-bootloader: fcef1579
hbootpreupdate: 11
gencheckpt: 0
region-id: 0
Thanks.
Click to expand...
Click to collapse
You need to flash boot.img in fastboot. Boot.img can be found in the rom zip files that you flashed earlier.
Sent from my Desire HD using xda premium
yumm91 said:
You need to flash boot.img in fastboot. Boot.img can be found in the rom zip files that you flashed earlier.
Click to expand...
Click to collapse
fastboot flash img boot.img
sending 'img' (2982 KB)...
OKAY [ 0.516s]
writing 'img'...
(bootloader) signature checking...
FAILED (remote: signature verify fail)
finished. total time: 1.001s
Doesn't work ...
If memory serves, you will need to downgrade your hboot first before you can flash a boot.img.
Sent from my Desire HD using xda app-developers app
romuloxiii said:
If memory serves, you will need to downgrade your hboot first before you can flash a boot.img.
Click to expand...
Click to collapse
Thanks for answers,
well I'm not sure how to do this
I have downloaded this RUU
OTA_Ace_Gingerbread_S_TELUS_WWE_2.43.661.1_R-1.84.661.1_R_release_194023aok9iw7hmtj4lilk.zip, Renamed it to PD98IMG.zip and flashed in
fastboot oem rebootRUU
fastboot flash zip OTA_Ace_Gingerbread_S_TELUS_WWE_2.43.661.1_R-1.84.661.1_R_release_194023aok9iw7hmtj4lilk.zip
and still nothing,
fastboot flash zip OTA_Ace_Gingerbread_S_TELUS_WWE_2.43.661.1_R-1.84.661.1_R_release_194023aok9iw7hmtj4lilk.zip
sending 'zip' (102227 KB)...
OKAY [ 17.309s]
writing 'zip'...
(bootloader) zip header checking...
(bootloader) zip info parsing...
FAILED (remote: 24 parsing android-info fail)
finished. total time: 24.653s
please correct me if I did everything wrong
My mistake was
fastboot flash zip boot.img,
after typing
fastboot flash boot boot.img
I got WORKING cm-7.2.0-ace.zip ROM
So far so good :fingers-crossed:
But, I have strange touchscreen behavior it touches not where I'm pressing but like 20mm to the left and none of the 4 buttons are working.
I've tried to download and install same ROM like 10 times but still the same.
On CM11 and CM10 I have only black screen.
Any ideas ?
Now I have CM-10 with touch screen problem.
I found out that for some ROM's I need to boot boot.img manually in fastboot mode because I'm S-on.
I have only touch screen problem now. I don't believe it's hardware problem because before everything it was working really well.
(I found some threads about it as well, but cleaning Dalvik cache or permission fixing didn't help.)
I really need help in here, thanks.
Gedaz said:
Now I have CM-10 with touch screen problem.
I found out that for some ROM's I need to boot boot.img manually in fastboot mode because I'm S-on.
I have only touch screen problem now. I don't believe it's hardware problem because before everything it was working really well.
(I found some threads about it as well, but cleaning Dalvik cache or permission fixing didn't help.)
I really need help in here, thanks.
Click to expand...
Click to collapse
are you already have tried flashing boot.img from fastboot...?
fastboot flash boot boot.img
JJeamy said:
are you already have tried flashing boot.img from fastboot...?
fastboot flash boot boot.img
Click to expand...
Click to collapse
I have solved booting problem like I said.
Before did flash zip boot.img instead of flash boot boot.img.
I don't know what to do with touchscreen, looks like all left side is not working and on the right side I have 2-3cm error to the left side...
Is it possible to get some kind of touch screen driver or video driver zip file to flash from recovery to try restore default value of touch screen ?.
I've flashed
lordmodUEv8.9-CFS-b7-2WCR-TUN.zip kernel from recovery but on the phone I still can see:
Kernel version
2.6.35.14-cyanogenmod-g295e82f
I can navigate on the phone only through androidscreencast.jnlp
Thanks.
Gedaz said:
I have solved booting problem like I said.
Before did flash zip boot.img instead of flash boot boot.img.
I don't know what to do with touchscreen, looks like all left side is not working and on the right side I have 2-3cm error to the left side...
Is it possible to get some kind of touch screen driver or video driver zip file to flash from recovery to try restore default value of touch screen ?.
I've flashed
lordmodUEv8.9-CFS-b7-2WCR-TUN.zip kernel from recovery but on the phone I still can see:
Kernel version
2.6.35.14-cyanogenmod-g295e82f
I can navigate on the phone only through androidscreencast.jnlp
Thanks.
Click to expand...
Click to collapse
i'm not sure is..but what i guest it's looks like a rom problem/bug indeed..
maybe you can try another rom that you sure that is not have major bug indeed..
try like carboon rom for JB and svhd rom for ICS,
but because the phone still s-on..then you must always flashing boot.img (from the rom.zip itself) manual too from fastboot after installing every any new custom rom..
hopefully this can help..
I have an HTC Desire HD.
I unlocked it
s-off
rooted
flashed with cwm recovery
installed from ZIP file on SDCARD
rebooted
stuck on HTC logo regardless of what I attempt.
I have no idea where to go from here.
Any ideas?
Thanks
did you made full wipe?
What ROM?....which version of cwm? These are important factors
ClockworkMod Recovery v 5.8.1.5
I have tried different ROMs, all end up with the same scenario
cm-10.1-20130301-unofficial -ace
cm-JellyTime_R17.zip
I hope this answer helps you help me
Can you access boot loader? If so , go to it and post results of "fastboot getvar all". Maybe running an ruu will get u back on track.
Yest, bootloader is accessible and I attempted an RUU and ended up with the same result.
I will post the results of getvar all when I get home, stuck in traffic now
Thanks
-----------------------------------------
Here is the result of getvar all:-
INFOversion: 0.5
INFOversion-bootloader: 2.00.0029
INFOversion-baseband: 26.14.04.28_M
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.13.0.0
INFOserialno: SH12CRX01945
INFOimei: 356299049756800
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: HTC__Y13
INFObattery-status: good
INFObattery-voltage: 4172mV
INFOpartition-layout: Generic
INFOsecurity: on
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: fcef1579
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.031s
Is this were it stops?
No one has any idea to what it could be, no need for an absolute solution, a mere possible or a reflection as to what I could have done wrong would be appreciated.
LOL
What can i say to you?
As you stated on very first post of yours where you mentioned that your device is S-OFF? then why "INFOsecurity: on" ??
Simply flash any custom rom then extract boot.img from that custom rom .zip file and flash it through fastboot using command "fastboot flash boot boot.img"
Afterwards it should boot normally. Recovery has no issue nor given rom as you've mentioned on your post. Just requires boot.img to be flashed as your device is S-ON! not S-OFF.
I read a little sarcasm in that LOL
Thanks for the valuable info, I will attempt that as soon as I get home.
I will give feedback as to how successful my attempt has been.
I have attempted the proposed solution and I got the following error:
failed (remote: signature verify fail)
I read that could have to do with the fact that my bootloader is locked again. I did run a while back fastbood oem lock.
oem unlock returns an error.
So I attempted with the htcdev unlock code.bin again and unlocked it.
I ran the boot.img as instructed again and this time it was a success although it gave me a scare with the 4 reboots it performed
Thanks for the help, the tip from dr.patron99 was very helpful.
Hi:
In Advantage, thank's for any help.
I get HTC Desire HD with rom:RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1_Radio_12.65.60.29_26.14.04.28_M_release_225512_signed.
I already tried to unlock the sim card but nothing! I inserte a O2 card but i cannot connect and don't ask me to put any code to unlock.
There is any chance someone tell me what i can do, please.
Regards
You can see how to s-off your desire hd with SuperCid and SimUnlock here.
You can also give us more informations about your device by giving the command
Code:
fastboot getvar all
from fastboot mode when you are in bootloader.
Hi:
Many thanks for the replay.
I believe is this that you ask me:
INFOversion: 0.5
INFOversion-bootloader: 2.00.0027
INFOversion-baseband: 26.14.04.28_
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.12.405.1
INFOserialno: HT0BFRX03894
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: 11111111
INFObattery-status: good
INFObattery-voltage: 4189mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: 743ca94a
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
Please i really need help i do know what do more.
Thanks
As I can see you already have S-OFF and SuperCid (11111111).
So the only thing that you will probably need is the radio exploit , a custom recovery and the gfree app.
Just download the tools I give you here and extract them into an empty directory.
Copy "PG98IMG.zip" to your sdcard root directory (It has md5 checksum file if you want to check it).
After that reboot your phone to bootloader and it should prompt you to upgrade radio and recovery.Allow it and let your phone reboot ones.
(After that you have to remove your sdcard in order to reboot to your recovery and run the exploit or you can just delete PG98IMG.zip from your sdcard.)
If you have not access to your rom:
Pull the battery out (just for safety)
Remove your sdcard.
Pull your battery back in.
Go to bootloader and open recovery from the options or use the command
Code:
fastboot reboot recovery
As long as you are in recovery run the commands
Code:
adb push gfree /tmp/
adb shell chmod 775 /tmp/gfree
adb shell /tmp/gfree -f
Reboot to bootloader to check the results...
Code:
adb reboot-bootloader
If you succeed those steps you should be (steel) S-OFFed , SuperCided and SimUnlocked.
After that you can flash any recovery and radio you like using PG98IMG.
** After this process succeed remove PG98IMG.zip from your sdcard before you put it back to your phone because if you don't, every time you boot into bootloader you will be prompted to flash it again**
Also you should never post your INFOserialno INFOimei online.Just leave them blank.
Hi:
Many thanks for replay.
I have copy the zip file but don't start the update. What i do wrong?
I need to downgrade?
Maybe your hboot version does not support direct flash from zip.Check my post here.
Yes you need to dowgrade your radio but in order to do that you should probably upgrade your hboot.If you upgrade it you can unlock your bootloader with htc_devs way too.After htc_devs unlock it should be flashable from fastboot mode without restrictions.(This way it is not nessesary as long as you are S-OFF user and you better take a backup of your data if you deside you unlock your phone by this way.)
Hi Mate:
I'm in same situation, i don't know what to do.
I send you already a private message.
Regards
aranha2222 said:
Hi Mate:
I'm in same situation, i don't know what to do.
I send you already a private message.
Regards
Click to expand...
Click to collapse
I saw your PM too.
1) Do you have a rooted rom?
2) Do you have USB debugging enabled to your phone and the correct adb drivers on your PC in order to use adb tool?
As long as you are S-OFFed you could also use fastboot commands to flash the zips using RUUmode instead of fastboot.
Just try to flash the zip with radio and custom recovery by using the commands
Code:
fastboot oem rebootRUU
fastboot flash zip PG98IMG.zip
You can also update your hboot version using the same method
Code:
fastboot flash zip rom.zip
After the proccess completes you have to use
Code:
fastboot reboot-bootloader
...and check your radio version (It should be different than before).After that get into recovery and follow gfree steps.
Hi:
Many thanks for your time.
But i was tried all morning and i believe i don't know what i'/m already doing.
Do you want i start from begin again or what you thing is better?
Regards
I tried, i flash the zip with radio and custom recovery but i still don't get any network signal.
Please, help me
aranha2222 said:
Hi:
Many thanks for your time.
But i was tried all morning and i believe i don't know what i'/m already doing.
Do you want i start from begin again or what you thing is better?
Regards
I tried, i flash the zip with radio and custom recovery but i still don't get any network signal.
Please, help me
Click to expand...
Click to collapse
You tried to flash the zip.I undestand that.But what way did you use to flash?(fastboot or RUUmode/did you tried both?) and did you succeded or you had some error?
If you are SimLocked you won't have signal until you make the gfree operation anyway.
Please answer me to my previews questions to be able to help you further.
Hi:
Let me explain (sorry i'm not a expert, i believe you already find that).
I get is HtC Desire HD, and coming with rom RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1_Radio_12.65.60.29_26.14.04.28_M_release_225512_signed.
After with tools you give me i use the commands :
fastboot oem rebootRUU
fastboot flash zip PG98IMG.zip
fastboot reboot-bootloader.
And that's it, i don't know what or how to do more.
This is the information:
INFOversion-bootloader: 2.00.0025
INFOversion-baseband: 26.03.02.26_M
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.13.0.0
INFOserialno: HT0BFRX03894
INFOimei:
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: 11111111
INFObattery-status: good
INFObattery-voltage: 4199mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: d065c8e9
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.008s
Many thank's for your support.
Regards
aranha2222 said:
Hi:
Let me explain (sorry i'm not a expert, i believe you already find that).
I get is HtC Desire HD, and coming with rom RUU_Ace_Sense30_S_HTC_WWE_3.12.405.1_Radio_12.65.60.29_26.14.04.28_M_release_225512_signed.
After with tools you give me i use the commands :
fastboot oem rebootRUU
fastboot flash zip PG98IMG.zip
fastboot reboot-bootloader.
And that's it, i don't know what or how to do more.
This is the information:
INFOversion-bootloader: 2.00.0025
INFOversion-baseband: 26.03.02.26_M
INFOversion-cpld: None
INFOversion-microp: 0438
INFOversion-main: 3.13.0.0
INFOserialno: HT0BFRX03894
INFOimei:
INFOproduct: ace
INFOplatform: HBOOT-7230
INFOmodelid: PD9810000
INFOcidnum: 11111111
INFObattery-status: good
INFObattery-voltage: 4199mV
INFOpartition-layout: Generic
INFOsecurity: off
INFObuild-mode: SHIP
INFOboot-mode: FASTBOOT
INFOcommitno-bootloader: d065c8e9
INFOhbootpreupdate: 11
INFOgencheckpt: 0
INFOregion-id: 0
all: Done!
finished. total time: 0.008s
Many thank's for your support.
Regards
Click to expand...
Click to collapse
Yes but you are not answering me.Do you get a success message for those operations or an error message??I mean through flashing the zip.What is the message you can see?
In any case try to flash only the hboot (rom.zip in my forth post) and see if you have hboot 2.00.0029.
Hi:
I tried but give me a error....
"error: cannot determine image filename for 'rom.zip'"
I used the commands:
fastboot oem rebootRUU
fastboot flash rom.zip:
aranha2222 said:
Hi:
I tried but give me a error....
"error: cannot determine image filename for 'rom.zip'"
I used the commands:
fastboot oem rebootRUU
fastboot flash rom.zip:
Click to expand...
Click to collapse
The last command is
Code:
fastboot flash zip rom.zip
Try again and tell me the results.If this doesn't work either just use the commands I am giving on the other post to flash the hboot from your rom.
Hi:
The Results:
C:\Users\GPS\Downloads\Tools_for_S-OFFed_Desire_HD_by_Gatosbil>fastboot flash zi
p rom.zip
sending 'zip' (264 KB)... OKAY [ 0.057s]
writing 'zip'... INFOzip header checking...
INFOshift signature_size for header checking...
INFOzip info parsing...
INFOchecking model ID...
INFOchecking custom ID...
INFOstart image[hboot] unzipping & flushing...
INFO[RUU]UZ,hboot,0
INFO[RUU]UZ,hboot,100
INFO[RUU]WP,hboot,0
INFO[RUU]WP,hboot,100
OKAY [ 10.227s]
finished. total time: 10.284s
Yes! You should have now hboot 2.00.0029!
Now you can try to flash PD98IMG.zip with custom radio and recovery from your sdcard through bootloader.
Use the command
Code:
fastboot reboot-bootloader
to reboot your device to bootloader.
Hi:
I put the file on sdcard but nothing happen....
And i do (see information, please):
C:\Users\GPS\Downloads\Tools_for_S-OFFed_Desire_HD_by_Gatosbil>fastboot
p PG98IMG.zip
sending 'zip' (15793 KB)... OKAY [ 2.619s]
writing 'zip'... INFOzip header checking...
INFOzip info parsing...
INFOchecking model ID...
INFOchecking custom ID...
INFOstart image[recovery] unzipping & flushing...
INFO[RUU]UZ,recovery,0
INFO[RUU]UZ,recovery,23
INFO[RUU]UZ,recovery,47
INFO[RUU]UZ,recovery,70
INFO[RUU]UZ,recovery,95
INFO[RUU]UZ,recovery,100
INFO[RUU]WP,recovery,0
INFO[RUU]WP,recovery,100
INFOstart image[radio] unzipping & flushing...
INFO[RUU]UZ,radio,0
INFO[RUU]UZ,radio,8
INFO[RUU]UZ,radio,16
INFO[RUU]UZ,radio,24
INFO[RUU]UZ,radio,33
INFO[RUU]UZ,radio,41
INFO[RUU]UZ,radio,49
INFO[RUU]UZ,radio,57
INFO[RUU]UZ,radio,62
INFO[RUU]UZ,radio,70
INFO[RUU]UZ,radio,79
INFO[RUU]UZ,radio,86
INFO[RUU]UZ,radio,95
INFO[RUU]UZ,radio,100
INFO[RUU]WP,radio,0
INFO[RUU]WP,radio,6
INFO[RUU]WP,radio,14
INFO[RUU]WP,radio,19
INFO[RUU]WP,radio,27
INFO[RUU]WP,radio,36
INFO[RUU]WP,radio,44
INFO[RUU]WP,radio,100
OKAY [ 35.427s]
finished. total time: 38.046s
C:\Users\GPS\Downloads\Tools_for_S-OFFed_Desire_HD_by_Gatosbil>fastboot
ootloader
rebooting into bootloader... OKAY [ 0.157s]
finished. total time: 0.158s
What i need to do?
aranha2222 said:
Hi:
I put the file on sdcard but nothing happen....
And i do (see information, please):
C:\Users\GPS\Downloads\Tools_for_S-OFFed_Desire_HD_by_Gatosbil>fastboot
p PG98IMG.zip
sending 'zip' (15793 KB)... OKAY [ 2.619s]
writing 'zip'... INFOzip header checking...
INFOzip info parsing...
INFOchecking model ID...
INFOchecking custom ID...
INFOstart image[recovery] unzipping & flushing...
INFO[RUU]UZ,recovery,0
INFO[RUU]UZ,recovery,23
INFO[RUU]UZ,recovery,47
INFO[RUU]UZ,recovery,70
INFO[RUU]UZ,recovery,95
INFO[RUU]UZ,recovery,100
INFO[RUU]WP,recovery,0
INFO[RUU]WP,recovery,100
INFOstart image[radio] unzipping & flushing...
INFO[RUU]UZ,radio,0
INFO[RUU]UZ,radio,8
INFO[RUU]UZ,radio,16
INFO[RUU]UZ,radio,24
INFO[RUU]UZ,radio,33
INFO[RUU]UZ,radio,41
INFO[RUU]UZ,radio,49
INFO[RUU]UZ,radio,57
INFO[RUU]UZ,radio,62
INFO[RUU]UZ,radio,70
INFO[RUU]UZ,radio,79
INFO[RUU]UZ,radio,86
INFO[RUU]UZ,radio,95
INFO[RUU]UZ,radio,100
INFO[RUU]WP,radio,0
INFO[RUU]WP,radio,6
INFO[RUU]WP,radio,14
INFO[RUU]WP,radio,19
INFO[RUU]WP,radio,27
INFO[RUU]WP,radio,36
INFO[RUU]WP,radio,44
INFO[RUU]WP,radio,100
OKAY [ 35.427s]
finished. total time: 38.046s
C:\Users\GPS\Downloads\Tools_for_S-OFFed_Desire_HD_by_Gatosbil>fastboot
ootloader
rebooting into bootloader... OKAY [ 0.157s]
finished. total time: 0.158s
What i need to do?
Click to expand...
Click to collapse
Congratulations!You have flash all the nessesary software.Now you have to go to recovery and give the gfree commands from my second post (If you see a black screen when you boot into recovery it is a good thing)
Hi:
What i have done:
C:\Users\GPS\Downloads\Tools_for_S-OFFed_Desire_HD_by_Gatosbil>adb push gfree /t
mp/
2892 KB/s (722728 bytes in 0.244s)
C:\Users\GPS\Downloads\Tools_for_S-OFFed_Desire_HD_by_Gatosbil>adb shell chmod 7
75 /tmp/gfree
C:\Users\GPS\Downloads\Tools_for_S-OFFed_Desire_HD_by_Gatosbil>adb shell /tmp/gf
ree -f
--secu_flag off set
--cid set. CID will be changed to: 11111111
--sim_unlock. SIMLOCK will be removed
Section header entry size: 40
Number of section headers: 44
Total section header table size: 1760
Section header file offset: 0x00015398 (86936)
Section index for section name string table: 41
String table offset: 0x000151df (86495)
Searching for .modinfo section...
- Section[16]: .modinfo
-- offset: 0x000011cc (4556)
-- size: 0x000000c4 (196)
Kernel release: 2.6.32.21
New .modinfo section size: 196
Attempting to power cycle eMMC... OK.
Write protect was successfully disabled.
Searching for mmc_blk_issue_rq symbol...
- Address: c02db21c, type: t, name: mmc_blk_issue_rq, module: N/A
Kernel map base: 0xc02db000
Kernel memory mapped to 0x40002000
Searching for brq filter...
- Address: 0xc02db21c + 0x34c
- 0x2a000012 -> 0xea000012
Backing up current partition 7 and patching it...
patching secu_flag: 0
Done.
Done, now what i need to do now?
Regards