I updated my Xperia Ion last night. Unfortunately, my phone was shut down by itself and then it've got bootloop but it s quite different from general bootloop because, when to Sony logo appear, it takes about 20 second and slowly disappear and reboot again about 6-7 times.
I've tried to carge it and i get the red led. However, it turns on automatically and everthing happen again. So, i tried to hard reset (3 vibrate) and do wall charging but it's still the same. After that, i've tried to use rubber band for flash mode while it was charging in red LED, but my laptop can't access my phone in flash mode and it's turned on by itself again. What should i do? Thank you in advance. :crying:
Naisamui99 said:
I updated my Xperia Ion last night. Unfortunately, my phone was shut down by itself and then it've got bootloop but it s quite different from general bootloop because, when to Sony logo appear, it takes about 20 second and slowly disappear and reboot again about 6-7 times.
I've tried to carge it and i get the red led. However, it turns on automatically and everthing happen again. So, i tried to hard reset (3 vibrate) and do wall charging but it's still the same. After that, i've tried to use rubber band for flash mode while it was charging in red LED, but my laptop can't access my phone in flash mode and it's turned on by itself again. What should i do? Thank you in advance. :crying:
Click to expand...
Click to collapse
ok...do this...once in bootloop...vol+ and power button.....then connect in flashmode...make sure you are doing it correctly...vol down/up+power button...if phone connects and disconnects then problem with drivers....install drivers and start over again
Dark Wraith said:
ok...do this...once in bootloop...vol+ and power button.....then connect in flashmode...make sure you are doing it correctly...vol down/up+power button...if phone connects and disconnects then problem with drivers....install drivers and start over again
Click to expand...
Click to collapse
I got the blue LED after that Flashtool told me that i need the driver. After that, my laptop installed the driver automatically and then Flashtool informed that my device connected with not debugging mode and MTP mode. now, i see just black screen and nothing happen and i can't reset or hard reset.
Naisamui99 said:
I got the blue LED after that Flashtool told me that i need the driver. After that, my laptop installed the driver automatically and then Flashtool informed that my device connected with not debugging mode and MTP mode. now, i see just black screen and nothing happen and i can't reset or hard reset.
Click to expand...
Click to collapse
it should be green led.blue led is fastboot mode i think. you need flashmode
and a little more details. what were you trying to update before your phone got into bootloop?got an unlocked B/L or locked?
One more thing. Go to flashtool folder>driver folder>drivers.exe(or something like that). Install drivers for your device first. then go to the bottom of the list. select flashmode and fastboot drivers and install those as well
Dark Wraith said:
it should be green led.blue led is fastboot mode i think. you need flashmode
and a little more details. what were you trying to update before your phone got into bootloop?got an unlocked B/L or locked?
One more thing. Go to flashtool folder>driver folder>drivers.exe(or something like that). Install drivers for your device first. then go to the bottom of the list. select flashmode and fastboot drivers and install those as well
Click to expand...
Click to collapse
Oh, I see. But I'm also trying to access the flashmode (down volume) but it still bootloop again. Anyway, I was installing custom rom in CMW and my ION is still Locked.
P.S. I can get i nfastboot mode but not for flashmode.
Naisamui99 said:
Oh, I see. But I'm also trying to access the flashmode (down volume) but it still bootloop again. Anyway, I was installing custom rom in CMW and my ION is still Locked.
P.S. I can get i nfastboot mode but not for flashmode.
Click to expand...
Click to collapse
you have CWM>???(CWM for locked Bl i guess)
Did you take a backup???
if not...check if ROM was meant for unlocked B/L. If not,wipe cache and dalvik cache..wipe data and try...
if yes, then u have only one option. Using flashmode(green led) use flashtools to flash stock firmware
Dark Wraith said:
you have CWM>???(CWM for locked Bl i guess)
Did you take a backup???
if not...check if ROM was meant for unlocked B/L. If not,wipe cache and dalvik cache..wipe data and try...
if yes, then u have only one option. Using flashmode(green led) use flashtools to flash stock firmware
Click to expand...
Click to collapse
yup, i used CMW for locked BL
and Yes,i did.
But, my phone doesn't respond me to get into flashmode
Naisamui99 said:
yup, i used CMW for locked BL
and Yes,i did.
But, my phone doesn't respond me to get into flashmode
Click to expand...
Click to collapse
if you can get into cwm just restore the backup.
Dark Wraith said:
if you can get into cwm just restore the backup.
Click to expand...
Click to collapse
For now, i can't access CMW anymore.
Naisamui99 said:
For now, i can't access CMW anymore.
Click to expand...
Click to collapse
Then switch it off completely...Put it to charge...(one hour or so)..open flashtool...now if fastboot mode is getting connected then flashboot would also work...search in google how to enter flash mode(which key combinations)..now initialize flashing and wen it asks to plug...plug it in flash mode(make sure u are not pressing power button)..it should be vol+/- only while plugging in....and tell me what does your log say after that...
Dark Wraith said:
Then switch it off completely...Put it to charge...(one hour or so)..open flashtool...now if fastboot mode is getting connected then flashboot would also work...search in google how to enter flash mode(which key combinations)..now initialize flashing and wen it asks to plug...plug it in flash mode(make sure u are not pressing power button)..it should be vol+/- only while plugging in....and tell me what does your log say after that...
Click to expand...
Click to collapse
Actually, I've done like this before. But I stuck in fastboot mode and i can't restart it. Is there anyway to enter flashmode from fastboot? I searched it but i can't find.
Naisamui99 said:
Actually, I've done like this before. But I stuck in fastboot mode and i can't restart it. Is there anyway to enter flashmode from fastboot? I searched it but i can't find.
Click to expand...
Click to collapse
do a reset again...vol plus + power button.... and then try
Dark Wraith said:
do a reset again...vol plus + power button.... and then try
Click to expand...
Click to collapse
That way give me enter in fastboot mode (Blue LED) :crying:
Naisamui99 said:
That way give me enter in fastboot mode (Blue LED) :crying:
Click to expand...
Click to collapse
search in xda for ion...for xperia s buttons might be different
Dark Wraith said:
search in xda for ion...for xperia s buttons might be different
Click to expand...
Click to collapse
I know how to enter Flash mode in Xperia Ion but, i can't reach that mode.
Naisamui99 said:
I know how to enter Flash mode in Xperia Ion but, i can't reach that mode.
Click to expand...
Click to collapse
Ok one by one.. Tell me can you switch off the phone completely?
Dark Wraith said:
Ok one by one.. Tell me can you switch off the phone completely?
Click to expand...
Click to collapse
Yes! because i've tried for 2 ways. The first way; Let its battery die because of bootloop. And the second is use the hard reset and let the battery die.
Related
I was installing cyanogen mod 10 via CWM and everything went fine until I rebooted after installing. The phone would not reboot in to android.
The phone is stuck on a black screen with no power light showing - it vibrates if I try a hard reboot but that is the limit of what it's doing. When it was plugged in via USB the computer installed a couple of drivers but that's it as far as any form of life goes.
Does anyone have any ideas ?
Is your bootloader unlocked?
CM10 only works on unlocked bootloader.
If your bootloader is locked, use PCC or Update Service to repair your phone.
ss002d6252 said:
I was installing cyanogen mod 10 via CWM and everything went fine until I rebooted after installing. The phone would not reboot in to android.
The phone is stuck on a black screen with no power light showing - it vibrates if I try a hard reboot but that is the limit of what it's doing. When it was plugged in via USB the computer installed a couple of drivers but that's it as far as any form of life goes.
Does anyone have any ideas ?
Click to expand...
Click to collapse
Do this -
1. Download stock ics ftf and prepare to flash it using Flashtool by androxyde
2. Press and hold the power and volume up combination until you get 3 vibrations
3. Now holding the volume down key, attach the usb cable and allow the flashing to get completed
4. Turn on your phone normally after the flashing and enjoy
Thanks.
I used the sony update service to get up and running again. As far as I was aware the bootloader was unlocked but presumably it was not which caused the problems ?
ss002d6252 said:
Thanks.
I used the sony update service to get up and running again. As far as I was aware the bootloader was unlocked but presumably it was not which caused the problems ?
Click to expand...
Click to collapse
It happened because you have not unlocked your boot loader properly.
Sent from my Xperia S using xda app-developers app
abcdjdj said:
It happened because you have not unlocked your boot loader properly.
Sent from my Xperia S using xda app-developers app
Click to expand...
Click to collapse
So how to fix that? IT seems that I have do the same, and now im stuck at bootloop. Cant even turn it off permanently.
Boshe said:
So how to fix that? IT seems that I have do the same, and now im stuck at bootloop. Cant even turn it off permanently.
Click to expand...
Click to collapse
To turn it off completely, press and hold the volume up + power combination until you get 3 vibrations. At this point, your device will be completely turned off. Now in order to unlock your bootloader, kindly follow this guide - http://unlockbootloader.sonymobile.com/instructions
Good luck
abcdjdj said:
To turn it off completely, press and hold the volume up + power combination until you get 3 vibrations. At this point, your device will be completely turned off. Now in order to unlock your bootloader, kindly follow this guide - http://unlockbootloader.sonymobile.com/instructions
Good luck
Click to expand...
Click to collapse
Thanks for the answer. Already find that and solve my problem.
xperia s totally bricked don't know what to do?
:crying::crying: i accidentally flashed cwm touch 6.0.4 touch and now it is bricked .....when i left it for charging the red light appears but as i unplug it red light go away. dont know what to do plz help....phone not detected by flash tool or emma or pc companion.
iknoxforu said:
:crying::crying: i accidentally flashed cwm touch 6.0.4 touch and now it is bricked .....when i left it for charging the red light appears but as i unplug it red light go away. dont know what to do plz help....phone not detected by flash tool or emma or pc companion.
Click to expand...
Click to collapse
Try the rubber band method from here.
Mirhawk said:
Try the rubber band method from here.
Click to expand...
Click to collapse
tried it kept it like this overnight but nothing happens
iknoxforu said:
tried it kept it like this overnight but nothing happens
Click to expand...
Click to collapse
It sometimes takes longer time to work. Did You get any sort of error on flashtool? Like error while flashing loader.sin? Also, does the phone get warm on the back side?
Mirhawk said:
It sometimes takes longer time to work. Did You get any sort of error on flashtool? Like error while flashing loader.sin? Also, does the phone get warm on the back side?
Click to expand...
Click to collapse
no error the phone is not booting to flashmode at all. neither it getting warm.
Hey guys I recently updated from FXP 320 to 323 and my device is Not TURNING ONN, It just gives a heptic feed back (vibrate) and sometime it doesnt even vibrate when I press and hold power button.. Just LED blicks 3 times in RED colour when I try to power onn device..
When I connect the charger the LED turns RED and it remains red even if I charger it for 3 hours or more. When I connect in FLASHBOOT or FASTBOOT MODE THE LED SHOWS RED and the pc doesnt detedt my device. What to do now? Is my device soft bricked or hard bricked? Is there any way to bring it back to life? Plz someone help me.
It's okay, it's just soft brick. Try to re-flash bro
Vroyaloko said:
It's okay, it's just soft brick. Try to re-flash bro
Click to expand...
Click to collapse
but how bhai? When I connect my device to PC, it doesnt detect
syedafzal.shah said:
but how bhai? When I connect my device to PC, it doesnt detect
Click to expand...
Click to collapse
Maybe the kernel is not compatible with the rom. Have you tried to change the kernel with fastboot? I had the same probleb with an xpreria mini and sola but after 6-7 tries it worked on fastboot, and then with the cwm i flashed via sd card the new rom.
syedafzal.shah said:
but how bhai? When I connect my device to PC, it doesnt detect
Click to expand...
Click to collapse
just go to flashtool folder the click on the drivers and open the program then tick flashmode and fastboot and click install wait till the driver installation finishes then connect your phone to pc..
Sent from my C1905 using Tapatalk 4
alexiskap said:
Maybe the kernel is not compatible with the rom. Have you tried to change the kernel with fastboot? I had the same probleb with an xpreria mini and sola but after 6-7 tries it worked on fastboot, and then with the cwm i flashed via sd card the new rom.
Click to expand...
Click to collapse
ok I will try that.
haresh311999 said:
just go to flashtool folder the click on the drivers and open the program then tick flashmode and fastboot and click install wait till the driver installation finishes then connect your phone to pc..
Sent from my C1905 using Tapatalk 4
Click to expand...
Click to collapse
ok. I will try this and get back to you as soon as I can
If you look at the fxp change log, they've integrated the latest Sony kernel.
Sent from my C1905 using XDA Free mobile app
syedafzal.shah said:
Hey guys I recently updated from FXP 320 to 323 and my device is Not TURNING ONN, It just gives a heptic feed back (vibrate) and sometime it doesnt even vibrate when I press and hold power button.. Just LED blicks 3 times in RED colour when I try to power onn device..
When I connect the charger the LED turns RED and it remains red even if I charger it for 3 hours or more. When I connect in FLASHBOOT or FASTBOOT MODE THE LED SHOWS RED and the pc doesnt detedt my device. What to do now? Is my device soft bricked or hard bricked? Is there any way to bring it back to life? Plz someone help me.
Click to expand...
Click to collapse
it really sound like a hard bricked to mee
if u can't enter fastboot or flashmode then there's nothing u can do
now the way is to take it to a sony service centre to repair it
you need to boot repair using flashing toolbox
i heard riff box will support xperia m from july.....
anyway best of luck:good:
ManzzaShahi said:
it really sound like a hard bricked to mee
if u can't enter fastboot or flashmode then there's nothing u can do
now the way is to take it to a sony service centre to repair it
you need to boot repair using flashing toolbox
i heard riff box will support xperia m from july.....
anyway best of luck:good:
Click to expand...
Click to collapse
No, Its not hard bricked if it was hard bricked It won't Vibrate also.
Sent from my C1905 using Tapatalk 4
haresh311999 said:
No, Its not hard bricked if it was hard bricked It won't Vibrate also.
Sent from my C1905 using Tapatalk 4
Click to expand...
Click to collapse
he can't enter fastboot mode as well as flashmode
and when he connects led turns red all time
if phone is alright then led gets green when battery is full
his device is not fully dead but cannot be recovered by using a usb cable or a flashtool which can be said as a hard bricked
the only way is to repair boot using flashing toolbox which can be done only in sony repair centre..
u can try this and report..
http://forum.xda-developers.com/showthread.php?t=1849170
Sent from my C1905 using Tapatalk 4
nice thread
but my device is working great so i don't need to try that
so let the op tries the tricks and share what he gets in result :good::good:
I connected my device in flashboot mode by holdig volume up button and the LED turned blue then I extracted the boot.img file from fxp 323 and flashed it by "fastboot flash boot boot.img" and it resulted " okay
, flashing boot
finished , total time 1.953s but when i disconnect the device and try to powewr onn the LED blinks 3 times in red and the device doesnt power on? what to do now?
haresh311999 said:
u can try this and report..
http://forum.xda-developers.com/showthread.php?t=1849170
Sent from my C1905 using Tapatalk 4
Click to expand...
Click to collapse
I connected my device in flashboot mode by holdig volume up button and the LED turned blue then I extracted the boot.img file from fxp 323 and flashed it by "fastboot flash boot boot.img" and it resulted " okay
, flashing boot
finished , total time 1.953s but when i disconnect the device and try to powewr onn the LED blinks 3 times in red and the device doesnt power on? what to do now?
ManzzaShahi said:
nice thread
but my device is working great so i don't need to try that
so let the op tries the tricks and share what he gets in result :good::good:
Click to expand...
Click to collapse
I connected my device in flashboot mode by holdig volume up button and the LED turned blue then I extracted the boot.img file from fxp 323 and flashed it by "fastboot flash boot boot.img" and it resulted " okay
, flashing boot
finished , total time 1.953s but when i disconnect the device and try to powewr onn the LED blinks 3 times in red and the device doesnt power on? what to do now?
and when i connect my device using volume down button, the led blinks in red and green colour just for a second and it goes off
syedafzal.shah said:
I connected my device in flashboot mode by holdig volume up button and the LED turned blue then I extracted the boot.img file from fxp 323 and flashed it by "fastboot flash boot boot.img" and it resulted " okay
, flashing boot
finished , total time 1.953s but when i disconnect the device and try to powewr onn the LED blinks 3 times in red and the device doesnt power on? what to do now?
Click to expand...
Click to collapse
first remove your battery from mobile for few minutes then insert again
then press and hold power on button for more than 10 seconds
then remove battery again from mobile and reinsert again and now try to connect to pc in flashboot mode
and flash full firmware wiping all cache and datas
if u can enter fastboot then u can access flashboot mode as well using volume down
try and report..
---------- Post added at 06:28 PM ---------- Previous post was at 06:21 PM ----------
syedafzal.shah said:
and when i connect my device using volume down button, the led blinks in red and green colour just for a second and it goes off
Click to expand...
Click to collapse
if led blinks green and off then you are in flashmode
so first make sure flashtool is running and your firmware is ready
press flash button in flashtool and flashtool will start preparing the files
when flashtool will say connect your device
then that time you hold volume down button and connect to pc
it will detect and start to flash
:laugh::laugh:
ManzzaShahi said:
first remove your battery from mobile for few minutes then insert again
then press and hold power on button for more than 10 seconds
then remove battery again from mobile and reinsert again and now try to connect to pc in flashboot mode
and flash full firmware wiping all cache and datas
if u can enter fastboot then u can access flashboot mode as well using volume down
try and report..
Click to expand...
Click to collapse
How to flash full firmware? can I install fxp323 using flashtool? how?
ManzzaShahi said:
first remove your battery from mobile for few minutes then insert again
then press and hold power on button for more than 10 seconds
then remove battery again from mobile and reinsert again and now try to connect to pc in flashboot mode
and flash full firmware wiping all cache and datas
if u can enter fastboot then u can access flashboot mode as well using volume down
try and report..
---------- Post added at 06:28 PM ---------- Previous post was at 06:21 PM ----------
if led blinks green and off then you are in flashmode
so first make sure flashtool is running and your firmware is ready
press flash button in flashtool and flashtool will start preparing the files
when flashtool will say connect your device
then that time you hold volume down button and connect to pc
it will detect and start to flash
:laugh::laugh:
Click to expand...
Click to collapse
Where should i paste FXP 323?
i have Xperia M C1905 and already updated to 15.4.A.1.9
and i want to boot into recovery mode
after code
fastboot reboot
Click to expand...
Click to collapse
the light notif turn become pink, but when i press volume up, my phone doesnt even reboot or anything its just stuck and the light become blue again like in fastboot mode, after that i tried pressing power mode and it vibrate and vibrate again but nothing happen, i tried removing my battery but nothing happen
can anyone help me?
sorry for my bad english
Meiruna said:
i have Xperia M C1905 and already updated to 15.4.A.1.9
and i want to boot into recovery mode
after code
the light notif turn become pink, but when i press volume up, my phone doesnt even reboot or anything its just stuck and the light become blue again like in fastboot mode, after that i tried pressing power mode and it vibrate and vibrate again but nothing happen, i tried removing my battery but nothing happen
can anyone help me?
Click to expand...
Click to collapse
Try to flash again the CWM recovery using flashtool,it happens when you upgrade it to the latest firmware.
prejudyce said:
Try to flash again the CWM recovery using flashtool,it happens when you upgrade it to the latest firmware.
Click to expand...
Click to collapse
solved, looks like im missing adb in flashtool, and that way phone not detected, after that flashing again work for me
thanks
Meiruna said:
solved, looks like im missing adb in flashtool, and that way phone not detected, after that flashing again work for me
thanks
Click to expand...
Click to collapse
It's my pleasure bro
Hi i have flash my phone with a miui firmware and everything was ok.
i have update the firmware for error and phone power off. the bootloader was open and i have a custom recovery.
now i cant go in recovery and flashmode and flashtool doesnt see it, when i press power and volume + the phone vibrate for 3-4 times and appears a light blue led and then it power off..
i connected the phone to the pc and i press volume+ and blue led appear, is it fast mode?
how can i do?
the users of this forum are the best
Sorry for my bad english
thanks :_(
That sounds like what happened to me recently. Basically, there are two modes the phone can go in when it's booting up and the USB is connected. One is fastboot mode, where you view the blue LED, which is what you are seeing. The other one, attained by pressing the other volume key, will get you into flash mode with a green LED and will allow you to use the flashtool to re-flash a stock firmware. I'm not entirely sure, but I think it's only if your bootloader is unlocked, but you should be able to try anyway.
festizzio said:
That sounds like what happened to me recently. Basically, there are two modes the phone can go in when it's booting up and the USB is connected. One is fastboot mode, where you view the blue LED, which is what you are seeing. The other one, attained by pressing the other volume key, will get you into flash mode with a green LED and will allow you to use the flashtool to re-flash a stock firmware. I'm not entirely sure, but I think it's only if your bootloader is unlocked, but you should be able to try anyway.
Click to expand...
Click to collapse
I try to go in flashmode but i cant do it flash tool doesnt see it when i try volume - and connected the green led doesnt appear
how can i do?
for solve your problem what did u do?
Thanks
Laquari95 said:
I try to go in flashmode but i cant do it flash tool doesnt see it when i try volume - and connected the green led doesnt appear
Click to expand...
Click to collapse
If there is activity in the flashtool when you connect then it doesn't matter about the led being lit.
XperienceD said:
If there is activity in the flashtool when you connect then it doesn't matter about the led being lit.
Click to expand...
Click to collapse
flash tool recognized the phone but says "connected debug off" after i try to go in flashmode and the led become red and than becomes green but for a secondo after the led turn off
Laquari95 said:
flash tool recognized the phone
Click to expand...
Click to collapse
Then you're good to go.
XperienceD said:
Then you're good to go.
Click to expand...
Click to collapse
yes now the phone is recognized but when it appears the window with the rules for flashong the device the z1c's led becames green but the flashing doesnt start how can i do?
Laquari95 said:
yes now the phone is recognized but when it appears the window with the rules for flashong the device the z1c's led becames green but the flashing doesnt start how can i do?
Click to expand...
Click to collapse
Watch some flashtool videos.
fickeo very
XperienceD said:
Watch some flashtool videos.
Click to expand...
Click to collapse
Now the phone isnt recognized oh sh^t, when i connected to the pc compaire led red, than turn it off, pink led and it turn it off...
yesterday was recognized :_(
try sony update service
XperienceD said:
Watch some flashtool videos.
Click to expand...
Click to collapse
the step that i do:
open flas toll
open the thunder
select the firmware to flash
click flash
says preparing flashinf
it open a window with the rules of flash mode
i press volume - and plug the cable, the led is red after its becames green for one second and it turn it off but the program doesnt start to flash
what wrong i do?
Thanks
Laquari95 said:
what wrong i do?
Click to expand...
Click to collapse
Put it on charge for an hour and try again, and don't let go of the volume button until it starts flashing.
XperienceD said:
Put it on charge for an hour and try again, and don't let go of the volume button until it starts flashing.
Click to expand...
Click to collapse
thanks my phone is reborn you are crazy you are the BEST i have vharge it and i dont release the volume- button and everything go right
I have put thanks to all your post
THANKS!!!!!!!!!!!
Laquari95 said:
thanks my phone is reborn you are crazy you are the BEST i have vharge it and i dont release the volume- button and everything go right
I have put thanks to all your post
THANKS!!!!!!!!!!!
Click to expand...
Click to collapse
:good:
thanks, that helped me to get my soft brick working again!
I tried to install CM11 on my xperia m. But after using the commands , fastboot flash boot boot.img and fastboot reboot.
After this the phone just displays "SONY" and then nothing happens. I am able to access the fastboot. Is there a way of doing a factory reset from the fastboot. If not then please tell me how i can make the phone to work ?
chotumotu11 said:
I tried to install CM11 on my xperia m. But after using the commands , fastboot flash boot boot.img and fastboot reboot.
After this the phone just displays "SONY" and then nothing happens. I am able to access the fastboot. Is there a way of doing a factory reset from the fastboot. If not then please tell me how i can make the phone to work ?
Click to expand...
Click to collapse
can you still get to flash mode in flashtool? or pc companion? just try it with pc companion first or with flash mode in flashtool? i think you can still fix your ohine?
Thanks a lot
Nicklas Van Dam said:
can you still get to flash mode in flashtool? or pc companion? just try it with pc companion first or with flash mode in flashtool? i think you can still fix your ohine?
Click to expand...
Click to collapse
Thank you for your help.
The cyanogenmod wiki has a mistake(or software bug in CM11) in its installation instruction for xperia m. To go to the clockworkmod menu I had to press the volume rockers after the light at the bottom turned pink and stop pressing them when the light turns light blue(a bit greenish). If I keep pressing the volume before that then it seems that the phone goes into a bootloop .
How ever i was not able to recover the official rom of sony.But i did manage to install the nightly build for CM11 .
But the phone now seems to be a little bit warmer than it used to be while using wifi. Is it ok?
Thanks again in advance.
chotumotu11 said:
Thank you for your help.
The cyanogenmod wiki has a mistake(or software bug in CM11) in its installation instruction for xperia m. To go to the clockworkmod menu I had to press the volume rockers after the light at the bottom turned pink and stop pressing them when the light turns light blue(a bit greenish). If I keep pressing the volume before that then it seems that the phone goes into a bootloop .
How ever i was not able to recover the official rom of sony.But i did manage to install the nightly build for CM11 .
But the phone now seems to be a little bit warmer than it used to be while using wifi. Is it ok?
Thanks again in advance.
Click to expand...
Click to collapse
ok you're welcome:laugh: