Solved - T-Mobile Samsung Galaxy S 4

My phone had many issue after upgrading to 4.3 , I tried to odin M919UVUEMK2_M919TMBEMK2_TMB.zip stock to fix it , now Odin fails everytime. Tried downloading new SW in case it was corrupt and using different ports same result. It also fails at different points , sometimes it fails right away and sometimes it goes all the way to the end then fails
knox 0x1
also said something about seandroid kernal
Any Ideas

re: flashing stock firmware
ransome7 said:
My phone had many issue after upgrading to 4.3 , I tried to odin M919UVUEMK2_M919TMBEMK2_TMB.zip stock to fix it , now Odin fails everytime. Tried downloading new SW in case it was corrupt and using different ports same result. It also fails at different points , sometimes it fails right away and sometimes it goes all the way to the end then fails
knox 0x1
also said something about seandroid kernal Any Ideas
Click to expand...
Click to collapse
The issue you are having has nothing to do with KNOX.
What I would do is to uninstall all samsung drivers as
well as kies from your computer.
Then reboot the computer and install the latest Samsung usb drivers.
Here is the direct download link for the samsung usb drivers:
https://www.dropbox.com/s/k7ut088zsc5g0un/Samsung USB Drivers.zip
Good luck!

Misterjunky said:
The issue you are having has nothing to do with KNOX.
What I would do is to uninstall all samsung drivers as
well as kies from your computer.
Then reboot the computer and install the latest Samsung usb drivers.
Here is the direct download link for the samsung usb drivers:
https://www.dropbox.com/s/k7ut088zsc5g0un/Samsung USB Drivers.zip
Good luck!
Click to expand...
Click to collapse
Did as you said uninstalled all samsung drivers including kies , reinstalled , reran odin same result
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUEMK2_M919TMBEMK2_M919UVUEMK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!

Odin will work if I do a recovery , but will not load the stock firmware to completion, just run it again and this time it went further before fail
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUEMK2_M919TMBEMK2_M919UVUEMK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sbl2.mbn
<ID:0/004> NAND Write Start!!
<ID:0/004> sbl3.mbn
<ID:0/004> rpm.mbn
<ID:0/004> aboot.mbn
<ID:0/004> tz.mbn
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img.ext4
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/004> Removed!!
<ID:0/004> Added!!

This time the green bar was all the way done and failed at 99%
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUEMK2_M919TMBEMK2_M919UVUEMK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl2.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl3.mbn
<ID:0/005> rpm.mbn
<ID:0/005> aboot.mbn
<ID:0/005> tz.mbn
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> modem.bin
<ID:0/005> NON-HLOS.bin
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!

ransome7 said:
This time the green bar was all the way done and failed at 99%
<ID:0/005> Added!!
<ID:0/005> Removed!!
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> M919UVUEMK2_M919TMBEMK2_M919UVUEMK2_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> sbl2.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl3.mbn
<ID:0/005> rpm.mbn
<ID:0/005> aboot.mbn
<ID:0/005> tz.mbn
<ID:0/005> boot.img
<ID:0/005> recovery.img
<ID:0/005> system.img.ext4
<ID:0/005> modem.bin
<ID:0/005> NON-HLOS.bin
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
<ID:0/005> Removed!!
<ID:0/005> Added!!
Click to expand...
Click to collapse
Try using a different usb port and/or cable, that has helped me in the past with random flash failures, both through ODIN and fastboot (for nexus devices).

klebs89 said:
Try using a different usb port and/or cable, that has helped me in the past with random flash failures, both through ODIN and fastboot (for nexus devices).
Click to expand...
Click to collapse
It was the cable , used a different samsung cable went though first time. Thanks for the input that was the nudge I needed

Related

Note 2 brick - Can't flash anything

Hey all,
I've a little Problem with my Note 2.
I got various Crashs in the last days so i decided to flash another Rom. Same Random Crashes.
So I said, okay, lets try Stock.
I used this guide: http://forum.xda-developers.com/showpost.php?p=31801046&postcount=1
and this Rom from that guide: N7100XXDMC3 N7100DBTDMB1 (till now i tried 5 or so ).
If i flash it via Odin, everything seems okay, but at reboot it goes straight into TWRP again. It seems it doesn't flash anything (even if it is working for Minutes...)
TWRP says cant mount '/data' so i cant flash anything from there so for now, i have a 500$ chopping Board
And because of DownloadMode showing Custom i cant send it to Samsung.
I'm sad
Any idea for i reason why odin can't flash anything?
My last to tries:
DBTDME2 from Sammobile.com
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXDME6_N7100DBTDME2_N7100XXDME4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> tz.img
<ID:0/004> system.img
<ID:0/004> boot.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> recovery.img
<ID:0/004> modem.bin
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
No change, still shows TWRP Logo on normal boot and on recovery boot twrp but cant mount data oder ext sd
So i tried to flash another Recovery , philz_touch_5.08.5.
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_5.08.5-n7100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
No change, TWRP all over.
pilzkopf92 said:
Any idea for i reason why odin can't flash anything?
My last to tries:
DBTDME2 from Sammobile.com
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXDME6_N7100DBTDME2_N7100XXDME4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> tz.img
<ID:0/004> system.img
<ID:0/004> boot.img
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> recovery.img
<ID:0/004> modem.bin
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
No change, still shows TWRP Logo on normal boot and on recovery boot twrp but cant mount data oder ext sd
So i tried to flash another Recovery , philz_touch_5.08.5.
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> philz_touch_5.08.5-n7100.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> recovery.img
<ID:0/004> NAND Write Start!!
<ID:0/004> RQT_CLOSE !!
<ID:0/004> RES OK !!
<ID:0/004> Completed..
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 1 / failed 0)
<ID:0/004> Removed!!
No change, TWRP all over.
Click to expand...
Click to collapse
Being unable to mount Data partition in most case means that it is corrupted. Have you tried Full Wipe from Recovery to format Data and Cache partitions? The next thing is to flash PIT file in Odin to completely reformat filesystem(s) - here is the file http://d-h.st/Dlv from this thread.
It's like takin a hammer to kill a fly but it should work (be mindefull it's for N7100 and not N7105).
mat9v said:
[...]to flash PIT file in Odin to completely reformat filesystem(s) [..] but it should work
Click to expand...
Click to collapse
Thanks but Sadly... it doesnt
Here is what odin Tells me:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXDME6_N7100DBTDME2_N7100XXDME4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Any Ideas? Searched at XDA and Google but nothin related
That looks like you have the SDS bug... Not all the emmc is corrupt in your case, since you have access to download mode... On which android version did you experience your first crashes? 4.1.1 or 4.1.2?
pilzkopf92 said:
Thanks but Sadly... it doesnt
Here is what odin Tells me:
Code:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXDME6_N7100DBTDME2_N7100XXDME4_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Set PIT file..
<ID:0/004> DO NOT TURN OFF TARGET!!
<ID:0/004> Get PIT for mapping..
<ID:0/004>
<ID:0/004> There is no PIT partition.
<ID:0/004> Added!!
<OSM> All threads completed. (succeed 0 / failed 1)
Any Ideas? Searched at XDA and Google but nothin related
Click to expand...
Click to collapse
Flash .pit file with the firmware, not alone make sure re-partition is ticked. Also, it may be a strange question, but are U using Download Mode or Odin Download Mode? Try on another computer with fresh drivers installation and no Kies or other Samsung stuff running.

[Q] Odin flash fails Note 2

<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUFNL1_N7100ODDFNI1_N7100DDUFND1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> tz.img
<ID:0/005> system.img
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
:crying::crying::crying::crying::crying::crying:
plzz help
im flashing it with 4.4.2
007skhan said:
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> N7100XXUFNL1_N7100ODDFNI1_N7100DDUFND1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Added!!
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> sboot.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> tz.img
<ID:0/005> system.img
<ID:0/005> boot.img
<ID:0/005> cache.img
<ID:0/005> hidden.img
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
:crying::crying::crying::crying::crying::crying:
plzz help
im flashing it with 4.4.2
Click to expand...
Click to collapse
change the usb cable?
Probably you have the stock recovery now.
Reboot in to Recovery, Format your device.
Flash your rom using ODIN again.

Flashing my Note 4 back to 4.4

Model: SM-N910A
This is what I get from ODIN.
<ID:0/007> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_ATT_N910AUCU1ANIE_N910AATT1ANIE_CL2774708_QB2373670_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/007> Odin v.3 engine (ID:7)..
<ID:0/007> File analysis..
<ID:0/007> SetupConnection..
<ID:0/007> Initialzation..
<ID:0/007> Set PIT file..
<ID:0/007> DO NOT TURN OFF TARGET!!
<ID:0/007> Get PIT for mapping..
<ID:0/007> Firmware update start..
<ID:0/007> SingleDownload.
<ID:0/007> aboot.mbn
<ID:0/007> NAND Write Start!!
<ID:0/007> sbl1.mbn
<ID:0/007> rpm.mbn
<ID:0/007> FAIL! (Auth)
<ID:0/007>
<ID:0/007> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
No matter what I do. I have tried using two different MD5's but no joy.
Any suggestions?
Thank you
I'm literally having the same exact issue. I'm on ATT. If you figure out whats wrong i'd appreciate it.
Here's my error code (i think identical to yours):
<ID:0/005> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> ALL_ATT_N910AUCU1ANIE_N910AATT1ANIE_CL2774708_QB2373670_REV00_user_low_ship_MULTI_CERT.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin v.3 engine (ID:5)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Set PIT file..
<ID:0/005> DO NOT TURN OFF TARGET!!
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> aboot.mbn
<ID:0/005> NAND Write Start!!
<ID:0/005> sbl1.mbn
<ID:0/005> rpm.mbn
<ID:0/005> FAIL! (Auth)
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
If you took the latest update, YOU CAN NOT ROLL BACK. I believe it is OCD5.
thepoetlives89 said:
If you took the latest update, YOU CAN NOT ROLL BACK. I believe it is OCD5.
Click to expand...
Click to collapse
Ughhhhhh!!!!!!! That sucks man.
Did you get it to work?
Hey guys
I'm in the same boat as you. Been trying all morning to flash using several different odins and images. By chance did you guys figure out a solution?
NO luck
facing same problem. Latest update messed up my network. Any SIM CARD not working,..

FAIL! flashing stock fiirmware 5.0.2, sm-t805 with odin 3.10

hi guys
i flashed stock firmware but odin failed midway... tab s shows the yellow triangle and "encountering an issue". i couldnt recover with kies. it also fails.
there's odin's log:
<ID:0/004> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T805XXU1BOCC_T805VFG1BOC4_T805XXU1BOC1_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/004> Odin v.3 engine (ID:4)..
<ID:0/004> File analysis..
<ID:0/004> SetupConnection..
<ID:0/004> Initialzation..
<ID:0/004> Get PIT for mapping..
<ID:0/004> Firmware update start..
<ID:0/004> SingleDownload.
<ID:0/004> sboot.bin
<ID:0/004> NAND Write Start!!
<ID:0/004> boot.img
<ID:0/004> recovery.img
<ID:0/004> system.img
<ID:0/004> modem.bin
<ID:0/004> cache.img
<ID:0/004> hidden.img
<ID:0/004> FAIL!
<ID:0/004>
<ID:0/004> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
i can access download mode. i can't download another rom cuz it took a week to download this one!! anyone can help me?
This is common when you flash a firmware not for your region. Easy fix, just boot to recovery and wipe cache then reboot. Everything should be fine after that.

Need Help!! Flash Fail SM-T111

Hi, my Samsung Galaxy Tab 3 Lite SM-T111 stuck at bootloop and keep restarting. So, I planed to do it myself. I downloaded the SM-T111 firmware and tried to flash it via Odin but fail. Below is the result :
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> T111XXUANF3_T111OLBANF3_T111XXUANF3_HOME.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/005> Odin engine v(ID:3.1005)..
<ID:0/005> File analysis..
<ID:0/005> SetupConnection..
<ID:0/005> Initialzation..
<ID:0/005> Get PIT for mapping..
<ID:0/005> Firmware update start..
<ID:0/005> SingleDownload.
<ID:0/005> timh.bin
<ID:0/005> NAND Write Start!!
<ID:0/005> obm.bin
<ID:0/005> DTim.Recovery
<ID:0/005> FAIL!
<ID:0/005>
<ID:0/005> Complete(Write) operation failed.
<OSM> All threads completed. (succeed 0 / failed 1)
Need help for this matter

Categories

Resources