I need help please, i have just upgrade my Note 2 to omega V19 now i have the following issues:
- My wifi is not working i dont know how to use odin to flash the fix.
- I reboot into recovery and i select the option to disable the stock recovery, now i dont have root access-
Please help me!! i need wifi and root!!
Read around the forum how to flash, then flash philz recovery using odin, and then flash Wi-Fi patch by Dr. Ketan from recovery.
Sent from my GT-N7100 using Tapatalk
Don't panic friend
Here what you should do:
1. Download ODIN 3.09
2. Download Dr.Ketan WiFi patch
3. Download PhilZ recovery in tar.md5 format (its available in developer post)
4. Download your favorite ROM (Dr.Ketan's v5 or DN3 v3 are my recommendations)
Now
5. Power off your phone
6. Enter in Download mode (Vol down+Home+Power)
7. Connect your phone with PC through USB cable
8. Put PhilZ recovery tar file in PDA column of ODIN 3.09 and hit START (make sure it is showing your device as added)
9. Don't remove your phone from cable till ODIN shows PASS
Do the same for WiFi patch after step 10 (flashing your ROM)
10. Enter in to Recovery (Volume UP + Home + Power) and flash your favourite ROM
Enjoy !!!
Good Luck !!!
Related
Rooting Indtruction
SINCE SUPERSU.ZIP DOES NOT WORK ON ALL DEVIVES THE BEST OPTION TO ROOT RIGHT NOW :
1ST: ROOT BY OPTION 2
2ND : FLASH CUSTOM CWM VIA PC ODIN OR MOBILE ODIN ( PLAY STORE )
Option 1: CWM + SuperSU .
1. download cwm6-recovery-n7100-121014.tar : http://www.mediafire.com/?mouxvj4og7azcow
OR Download cwm recovery V6.0.2.5 .tar: http://www.mediafire.com/?oyv15gidjxd6c23 . Big thank to Dr.Ketan&KoushThis CWM will not support EXFAT Card
2.download CWM SUPERSU V0.99 installable ZIP: I took off download link until further notice. From Chainfire " SUPERSU. ZIP does not work on all devices, needs fix. Note that if you are already rooted, installing through Market is by far the easiest way to install SuperSU !". More infor here http://forum.xda-developers.com/showthread.php?t=1538053
3.Download PC Odin : http://d-h.st/SdH
4.Open Odin and select PDA tab
5.Point to extracted file cwm6-recovery-n7100-121014.tar
6.Now switch off device and reboot in download modeby:
press Vol down + Home +Power, And then, press Volume UP button in Warning Page to enter the Download Mode
7.Connect device to PC and wait till device successfully added to com port (it will turn light blue)
8.Hit ‘Start’ to flash
9.Once it flashed successfully, you can see 'PASS' in table above the ID :COM, you can disconnect device from PC
10.Now reboot into CWM by :Switch off device and press Vol Up + Home +Power hold about 5 second
11.Install SuperSu.
12.Reboot.Done
Option 2 : Only Root
Download this CF Auto Root from here http://download.chainfire.eu/264/CF-Root/CF-Auto-Root/CF-Auto-Root-t03g-gtn7100.zip
and extract it to .tar
Procedure :
1.Open Odin and select PDA tab
2.Point to extracted file CF-Auto-Root-SGN2.tar
3.Now switch off device and reboot in download mode
press Vol down + Home +Power, And then, press Volume UP button in Warning Page to enter the Download Mode
4.Connect device to PC and wait till device successfully added to com port (it will turn light blue)
5.Hit ‘Start’ to flash
6.Once it flashed successfully, you can see 'PASS' in table above the ID :COM, you can disconnect device from PC
7.Reboot device and you will have superSU in application drawer.
Option 3 : Root with Exynos Abuse Apk
3.Root with apk No counter reset needs, Easiest - Credit goes to Chainfire, alephzain
1.Download latest from chainfire's here http://forum.xda-developers.com/showpost.php?p=35512626&postcount=1
2.Install application as routine apk installation and open it.
3.Open Exynos Abuse application from App drawer
4. Select Root Device
6.Now your device is rooted, for security purpose you can disable Exploit.
( Note : This may break camera, but unchecking disable exploit make it working again )
7. Open SuperSU & Update binary.
How to unroot Exploit :
Open Exynos Abuse app, uncheck disable explot & Disable Exploit on boot then select Unroot device
Restart device and wait for 10 min. and then you can check status.
Since Chainfire support our note now . if you want reset counter for warranty then download TRIANGLE AWAY from play store which will do the job.Still dont know what is it, go here for more infor http://forum.xda-developers.com/showthread.php?t=1494114.
If you want to unroot for some reason :
From stock rom and root by Chainfire method all you need to do : Triangle Away app ,SuperSU / setting/ full unroot. Reboot into Recovery / Factory reset.
From custom rom : reflash stock image via Odin .reroot by CF auto root,reset counter with Triangle Away App,SuperSU/Setting/Full unroot . Recovery / Factory reset.
Can find stock firmware from here http://www.sammobile.com/firmware/ search for T889
Stock T889UVALJ1 & T889UVALK8 (Post 51) http://forum.xda-developers.com/showthread.php?t=1969551 ( Thank , TeshXX)
Stock + root http://forum.xda-developers.com/showthread.php?t=1975560 ( Thank , Mr.Robinson )
How to flash rom via Odin :
Make sure you have installed Kies OR Samsung USB driver
Open up the ODIN
1. Enable the check mark by click on the following options(default Option)
- Auto Reboot, and F. Reset Time
- Download TAR ROM
- Check PDA, and point to TAR ROM file
2. Now switch off device and Enter into Download Mode
- Enter into Download Mode by pressing Volume Down button, Home Key and
Power Button simultaneously. And then, press Volume UP button in Warning Page to enter the Download Mode.
3. Connect the device to PC via Data Cable.
Make sure that the one of communication port [ID:COM] box is highlighted in
light blue. The device is now connected with the PC and ready to download the
binary file into the device.
4. Start downloading binary file into the device by clicking Start Button on the screen.
the green colored "PASS!" sign will appear on the upper-left box if the binary file
has been successfully downloaded into the device.
5. Disconnect the device from the Data cable.
6.Done
Common question about reseting counter
I have reset counter but system status still 'custom'
You should have stock recovery (Opton 2)
If you already have stock recovery(CF Auto root) then reset counter first
then wipe cache + wipe data(factory reset) + re wipe cache
You should now have system status 'official'
I have rest counter but after reboot again it goes to 1
This happen if you have rooted with CUSTOM RECOVERY(Opton 1)
This is neither error of recovery nor triangle away. This happens due to new bootloader which have auto checksum for recovery, when you reboot to custom recovery count will raise.
To prevent this you need to have play version of Triangle away, and you should check (enable) 'Auto reset at boot'. Again this feature depends on kernel/recovery is supported or no
How to Backup EFS : http://forum.xda-developers.com/showthread.php?t=1922473
Flash tool for Linux user : http://forum.xda-developers.com/showthread.php?p=33074572
Special thank to Dr.Ketan , Chainfire , Chenlu ,Koush, Alephzain , Mr.Robinson , TeshXX.
---------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
If you think my post was useful please hit thank consider like small donation.
Awesome, thanks for the info, getting mine this weekend!!
Where did you buy yours? TMO or wirefly??
your links are not working.
That my dear children, is not how you do copy paste.
the files are:
cwm6
https://hotfile.com/dl/176065007/332cffb/cwm6-recovery-n7100-121014.tar.html
and
CWM SUPERSU installable ZIP
http://forum.xda-developers.com/showthread.php?t=1538053
iamfightaa said:
your links are not working.
Click to expand...
Click to collapse
reupload.
B.Jay said:
"How to root" and similar threads do NOT belong into the Development boards!
Moved into General.
Next time watch where you post.
Thank you.
Click to expand...
Click to collapse
my bad.
simplelife said:
I had very easy method to flash which i did try by myself and work perfect with T889:
1. download cwm6-recovery-n7100-121014.tar : http://www.mediafire.com/?mouxvj4og7azcow
2.download CWM SUPERSU installable ZIP:http://www.mediafire.com/?w3i20sr6r58r8ah ( copy this file into your EXcard )
3.Download PC Odin : http://d-h.st/6Er
4.1.Open Odin and select PDA tab
2.Point to extracted file cwm6-recovery-n7100-121014.tar
3.Now switch off device and reboot in download modeby:
press Vol down + Home +Power, And then, press Volume UP button in Warning Page to enter the Download Mode
4.Connect device to PC and wait till device successfully added to com port (it will turn light blue)
5.Hit ‘Start’ to flash
6.Once it flashed successfully, you can see 'PASS' in table above the ID :COM, you can disconnect device from PC
7.Now reboot into CWM by :Switch off device and press Vol Up + Home +Power hold about 5 second
8.Install SuperSu.
9.Reboot.Done
Take about 5 min to do.Special thank to Dr.Ketan , Chainfire , Chenlu..
Click to expand...
Click to collapse
This method works 100%..I did it last night.
Sent from my SGH-T889 using Tapatalk 2
B.Jay said:
"How to root" and similar threads do NOT belong into the Development boards!
Moved into General.
Next time watch where you post.
Thank you.
Click to expand...
Click to collapse
Weird, I guess the development forums for 150 other phones must be wrong then. Their moderators must be slacking.
p.s.-no root, no development.
p.s.s-you must be a toolkit user
lowandbehold said:
Weird, I guess the development forums for 150 other phones must be wrong then. Their moderators must be slacking.
p.s.-no root, no development.
p.s.s-you must be a toolkit user
Click to expand...
Click to collapse
Yeah, the reason I put my thread in origin dev because i seen every forum do the same ,all I do is try to help but I guest moderator want to keep dev thread at NEVER so let it be. Toolkit is good but complicated if you choose wrong option then will be problem thats why I come up with this solution which easy to root and with out any issue .
jshaw06 said:
This method works 100%..I did it last night.
Sent from my SGH-T889 using Tapatalk 2
Click to expand...
Click to collapse
I glad someone confirm work
Can also confirm it works and please thank the OP for posting "How to" ... This however does not belong in Development, How to belong in General.. Thanks Mod for not slacking..
ellac49 said:
Can also confirm it works and please thank the OP for posting "How to" ... This however does not belong in Development, How to belong in General.. Thanks Mod for not slacking..
Click to expand...
Click to collapse
Yes, you are right! It belongs in the general section and not stickied in the dev section (like every other phone) so it can get lost on page 8 and more people **** up their phone.
Seriously. Go in the dev section of 20 different phones and tell me what percentage have a root method stickied right at the top.
I also was able to root my phone with this method.
Back to Stock?
Hi,
Are we able to bring it back to stock just in case?
Thanks
CLopez92868 said:
Hi,
Are we able to bring it back to stock just in case?
Thanks
Click to expand...
Click to collapse
should be in matter of time
The zip root. This only installs cwm recovery still need a rooted rom.
Sent from my SGH-T889 using xda premium
confirming that this method worked on my Note 2. :good:
this should be stickied.
tuffCookie said:
confirming that this method worked on my Note 2. :good:
this should be stickied.
Click to expand...
Click to collapse
Did the SU zip work for u?
Sent from my SGH-T889 using xda premium
VIIRU§ said:
Did the SU zip work for u?
Sent from my SGH-T889 using xda premium
Click to expand...
Click to collapse
yup
tuffCookie said:
yup
Click to expand...
Click to collapse
Can u link me the zip your using cause I flashed and it went thru but just didnt give me root. But I do have a custom recovery.
Sent from my SGH-T889 using xda premium
CWM v6.0.5.1 recovery for S3 Neo
---------------------------------------------------------------------------------------------------------------------------------------------------------
Installation:
1st Method ( Flashable ZIP )
1. Download CWM flashable zip for S3 Neo and transfer it to your phone
2. Boot your device into recovery ( Vol Up + Home+ Power )
3. Install TWRP flashable zip
4. Now you have TWRP recovery on your device ( Boot with vol up + home + power )
2nd Method ( Odin method )
1. Download recovery.tar.md5
2. Download ODIN and Samsung USB drivers
3. Boot device in download mode ( Vol down + home + power )
4. Press volume up ( continue ) and connect phone with PC
5. Make sure Odin recognizes your phone ( There should write somethiing like "0:[COM11]" in first box and it will be yellow )
6. Press PDA and navigate to recovery.tar.md5
7. Make sure Re-partition is unchecked
8. Press "Start" and wait few seconds
9. Device will reboot and you will have CWM recovery on your device ( Boot with vol up + home + power )
3rd method ( Terminal emulator - requires rooted device )
1. Download cwm.img and transfer it to your phone ( i will use /sdcard but it is optional)
2. Download Terminal Emulator from playstore
3. Open Teminal emulator and type
NOTE: It is VERY IMPORTANT to write this correctly because you are risking to hard brick your device if you mistype number, double check before pressing enter
Code:
su
dd if=/sdcard/cwm.img of=/dev/block/mmcblk0p15
or to be 100% sure you can write this, effect is same
Code:
su
dd if=/sdcard/cwm.img of=/dev/block/platform/msm_sdcc.1/by-name/recovery
Note: You can change path to recovery.img to your optional
4. Now you have TWRP recovery on your device ( Boot with vol up + home + power )
Enjoy!
---------------------------------------------------------------------------------------------------------------------------------------------------------
If you want to support my work you can donate me coffe. Use "Send payment" option on paypal ( [email protected] ) because "Donate" option is not available in my contry. Thanks.
---------------------------------------------------------------------------------------------------------------------------------------------------------
thanks work fine for me good job :good::good::good:
good job Rox and thank you
download link is broken
uzzo85 said:
download link is broken
Click to expand...
Click to collapse
tested just now link are work
spawk said:
tested just now link are work
Click to expand...
Click to collapse
thanks man, right now it work!!
I'm sorry but...although I have 11 posts, I still can't see the flashable zip link...
nicese said:
I'm sorry but...although I have 11 posts, I still can't see the flashable zip link...
Click to expand...
Click to collapse
+1
Sent from my GT-I9301I
There is no flashable zip file, only image file (3rd method) via adb/terminal emulator or via flashify & co.
Thanks, the 3rd method didn't work but I solved with Flashify :good:
Updated link in 3rd method, now cwm recovery is flashing and wiping faster ! And it can be installed on both variants ( GT-I9300I AND GT-I9301I )
thanks it worked perfectly and easily installed .
edit : damn it , flashing is realy fast
Now you can flash CWM using odin
Rox said:
CWM v6.0.5.1 recovery for S3 Neo
---------------------------------------------------------------------------------------------------------------------------------------------------------
Installation:
2nd Method ( Odin method )
1. Download recovery.tar
2. Download ODIN and Samsung USB drivers
3. Boot device in download mode...
---------------------------------------------------------------------------------------------------------------------------------------------------------
Click to expand...
Click to collapse
The recovery.tar link is dead. Can you reapload, please?
Edit: I think this is the new link
does it work for I9301I
Odin fails.
If I try to flash with odin the recovery.tar, it fails. I'm using GT-I9301I. Please help! Thanks!
I will check it...
Odin Stuck in Recovery.img using the recovery.tar given in the method 2.
Sorry for bother again Rox, but I can't install this CWM on my device. Odin fails
Odin file updated now, there shouldnt be troubles with odin flashing anymore
For anyone who wants root / twrp and to get phone to deep sleep (saves battery). This is what to do. hope it helps.
Link to put s6 edge drivers on computer
--------------------
http://androiddrivers.net/samsung-android-drivers/galaxy-s6-s6-edge-windows-drivers/
Link to download odin
--------------------
http://highonandroid.com/download-odin-v3-10-6/
Link to root/stock recovery/twrp/kernel files
https://www.dropbox.com/sh/c9fpn30htvmk9lx/AADzxyu1OBb7oFui9YCXYLoKa?dl=0
Credits go to @eousphoros for his hard work to bring us a great working version of twrp and his custom kernel
How to put phone in download mode:
- turn phone off
- hold power/home button/volume down until you are in download mode
- press Volume up to continue
You are now in download mode for Odin
To flash files in Odin use the AP tab in the Odin program
Instructions
---------------------
-Boot to download mode and Odin this CF-Auto-Root-zerofltetmo-zerofltetmo-smg920t.tar.md5
-Reboot
-Go back to download mode and Odin recovery.tar.md5
-Reboot
-Put twrp-2.8.6.0v2-zeroltetmo.img and newbootv3.img to your phone.
-On your phone, download Flashify from google play
-Open Flashify and flash the twrp-2.8.6.0v2-zeroltetmo.img (flash as recovery)
-Reboot
-Go back to Flashify and flash newbootv3.img. (flash as boot)
-Reboot
-Done
I did not write this up so I don't take any credit for it. Here is the link I copied it from. I just wanted to post it to where it is easy to find.
http://forum.xda-developers.com/showthread.php?p=60325927
credits go to @dungtran88 for the instructions ?
How to go back to stock video
https://youtu.be/kKU7otLN8N4
Stock file download
http://stockroms.net/file/GalaxyS6Edge/SM-G925T/SM-G925T_1_20150327095252_d1ygbqk7km.zip
I'm interested.
Please kindly elaborate how flashing a custom recovery helps with the deep sleep issue?
Regards
dnkeyhnter said:
For anyone who wants root / twrp and to get phone to deep sleep (saves battery). This is what to do. hope it helps.
Link to download odin
--------------------
http://highonandroid.com/download-odin-v3-10-6/
Links to needed files
---------------------
http://1drv.ms/1yWGCsq
How to put phone in download mode:
- turn phone off
- hold power/home button/volume down until you are in download mode
- press Volume up to continue
You are now in download mode for Odin
Instructions
---------------------
-Boot to download mode and Odin this CF-Auto-Root-zerofltetmo-zerofltetmo-smg920t.tar.md5
-Reboot
-Go back to download mode and Odin recovery.tar.md5
-Reboot
-Put twrp-2.8.6.0v2-zeroltetmo.img and newbootv2.img to your phone.
-On your phone, download Flashify from google play
-Open Flashify and flash the twrp-2.8.6.0v2-zeroltetmo.img (flash as recovery)
-Reboot
-Go back to Flashify and flash newbootv2.img. (flash as boot)
-Reboot
-Done
I did not write this up so I don't take any credit for it. Here is the link I copied it from. I just wanted to post it to where it is easy to find.
http://forum.xda-developers.com/showthread.php?p=60325927
Click to expand...
Click to collapse
The rooting method will make you lose stock recovery causing the issue. You must flash the stock recovery back for things to be right again. Flashing the custom recovery doesn't necessarily help with the deep sleep issue. But if you do want the custom recovery you must flash things in this order so you do not lose the phones ability to go into deep sleep mode.
For those who don't want custom recovery can just skip that step in flashify. Everything should still be fine since after you root, you boot back to Odin to flash the stock recover which fixed the sleep issue.
Sent from my SM-G925T using XDA Premium HD app
Stock download link added to OP / v3 kernel added
Please quick answer !!!
http://forum.xda-developers.com/galaxy-note-10-2014/general/root-root-stock-kernel-t3240218
And could someone explain to me step by step how to upload the root and recovery ? Because I too unknown to android .
kacper12897 said:
And could someone explain to me step by step how to upload the root and recovery ? Because I too unknown to android .
Click to expand...
Click to collapse
You can find how to root here. FULL CREDITS GO TO Zionator as he wrote up the instructions.
Easy Guide to Root :
1. Go to Rooting Guide - http://forum.xda-developers.com/gala...6#post63637426
Download only the P605 modded boot IMG and then come back here. Move the tar to tablet. "In my opinion that guide is very confusing" This is much more simple...
2. Go to TWRP (download version 2.8.7.0) - https://dl.twrp.me/lt03wifiue/
Download the img.tar This file you keep on pc to flash via Odin.
3. Go to SuperSU v2.52 Beta - https://download.chainfire.eu/743/Su...erSU-v2.52.zip
Download the zip. Move the zip to tablet.
4. Reboot the tablet into download mode and open Odin on the PC then connect the tablet to PC. In Odin click AP tab and locate the TWRP and uncheck Auto-Reboot then hit start. When done hold the power button + vol up button "the vol button furthest from power button" + home button til you see red writing on top right hand corner. This can take a while so don't panic just wait.
5. When finished booting into TWRP pull Spen and click Install then find modded boot img "remember to switch between IMG & ZIP mode in the lower left hand corner" Now flash the boot img. Do not reboot just go back and switch back to ZIP mode and flash SuperSU when done reboot.
6. Wait for the boot to finish. You are now rooted.
I hope this makes it easy for you!!!
thank you for the guide buhohitr.
worked perfectly for me
buhohitr said:
You can find how to root here. FULL CREDITS GO TO Zionator as he wrote up the instructions.
Easy Guide to Root :
1. Go to Rooting Guide - http://forum.xda-developers.com/gala...6#post63637426
Download only the P605 modded boot IMG and then come back here. Move the tar to tablet. "In my opinion that guide is very confusing" This is much more simple...
2. Go to TWRP (download version 2.8.7.0) - https://dl.twrp.me/lt03wifiue/
Download the img.tar This file you keep on pc to flash via Odin.
3. Go to SuperSU v2.52 Beta - https://download.chainfire.eu/743/Su...erSU-v2.52.zip
Download the zip. Move the zip to tablet.
4. Reboot the tablet into download mode and open Odin on the PC then connect the tablet to PC. In Odin click AP tab and locate the TWRP and uncheck Auto-Reboot then hit start. When done hold the power button + vol up button "the vol button furthest from power button" + home button til you see red writing on top right hand corner. This can take a while so don't panic just wait.
5. When finished booting into TWRP pull Spen and click Install then find modded boot img "remember to switch between IMG & ZIP mode in the lower left hand corner" Now flash the boot img. Do not reboot just go back and switch back to ZIP mode and flash SuperSU when done reboot.
6. Wait for the boot to finish. You are now rooted.
I hope this makes it easy for you!!!
Click to expand...
Click to collapse
404 Page Not Found
Oh snap! Something broke! A genius monkey has been alerted.
Until he fixes it, use our glorious search tool to find ROMs, apps, tools, and other sweet mods for your phone.
haha.... http://forum.xda-developers.com/gala...ernel-t3240218
can anyone here tell me how to downgrade from 5.1 lollipop to kitkat? i tried downloading the kitkat firmware from sammobile and flashing it via odin but it fails
Go into recovery, select wipe, advanced wipe and then check cache, dalvik cache, data, internal storage(make a backup) and system. When that's done, power down your device, boot into download mode and flash stock kitkat rom via Odin. I hope this helps
First do a factory reset if you are not rooted
If you have root and twrp installed do as follows : go in twrp (power + vol up + home) select Wipe > advanced wipe and wipe everything except external sd
1. Go to this link http://www.sammobile.com/firmwares/database/SM-N7505/ and select your country then download a firmware 4.1.1 version.
>Note: Create a free account on the samsung page to get full download speed as provided by your ISP. Mine is 100 kpbs
2. Then download odin from here > http://odindownload.com/download/#.VxKXaVRxeFU > Scroll down and click Download now button which is blue color.
3. After you have downloaded your firmware extract it to your desktop, then extract odin
4. Run Odin3 v3.10.7 then click AP then browse where you extracted the firmware and select it and click open.
5. Wait for it as Odin will says not responding but patience.
6. After it fully loads then Switch off your phone,
boot in download mode ( Hold power and vol - and home )
then press vol + to continue
plug usb cable in phone and pc. see msg added in odin
then click start on odin. wait till your phone reboots. do not unplug until its fully booted.
7. Now you have kitkat again.