Xperia ion soft brick just follow my steps 100% guranteed - Sony Xperia S, Acro S, Ion

Hello everybody , to all mates who bricked their phones by upgrading or using custom roms
I had soft brick my phone 3 times before and i read all soft brick methods here in our lovely forum, if u can my steps you will recover your phone 100%.
Note: remove your sd card and put it in PC and upload a custom rom in it, then bring it back to phone.
Lets go
1-]first of all these for unlocked boot loader.
2- after your phone die, connect to wall charger, at first will be no response (no red led) its OK don't be afraid.
3- charge it till red led on (it may takes many hours first time it need from me 22 hours, but usually need 10-15 hours).
4- now boot loops will start , its OK you are almost done believe me, prepare flash-tool in PC but do not select any thing.
5- while phone boot loop connect phone to your PC and do soft reset, ie hold power bottom and up volume bottom your phone will vibrate once now let power bottom and keep pushing up volume bottom (the phone is connected to PC as we said), blue led will appear which mean you are in fast-boot mode.
6- in flash tool select fast boot mode, a dialogue will appear select now (Select kernel To Flash), a window will appear choose from it JB_211_Kernel_twrp2.5.elf kernel or any CWM support kernel and flash it.
7- you will see the dialogue of flashing which till you that flashing is OK..
8 - now select reboot system from flash tool, your phone will restart.
9- enter recovery and select wipe all (advanced) system, data, cash and davlik cash, only leave internal memory and sd card
10- now select back and choose install and select any custom rom you have put in sd card and install it, after that select reboot system and you will go :laugh: its working believe me the phone will boot.
11- if you want to flash it with stock rom, after you boot recovery select power option and select power off (do not choose reboot) your phone will turn off, now prepare flash tool in PC and select your stock rom, wait till a pop up message appear to connect phone, connect your phone in flash mode ( volume down key and connect phone to PC) and flash stock rom .
Guys it really works do not ever give up try and try and you will recover your phone.
Please guys any one try this tell me the result I will help as I can.

A HUGE Thank you
Thank you sooo much... none of other method works but this did..... and finally resurrect my xperia Ion now, trying everything after two days.
TBH.. i had ignored this method for two days... and now i had to say oh yes i should do this before rather than waisting 2 days :laugh: :good: :victory:

HDilawari said:
Thank you sooo much... none of other method works but this did..... and finally resurrect my xperia Ion now, trying everything after two days.
TBH.. i had ignored this method for two days... and now i had to say oh yes i should do this before rather than waisting 2 days :laugh: :good: :victory:
Click to expand...
Click to collapse
I am so happy to hear that from you thanks my friend

Hello again
Hello again i have bricked my ion again..bootloader unlocked..
this time, when i flashed kernel with twrp... it is success.. i did wipe all things you said but after flashing, it was success too but on reboot it shows only sony logo then Exclamation mark in triangle phone beneath it.....
plz help me i this case.. my phone is just a year old..

Please help me..
After a long research of my phone, i found that whole os is removed form my Ion..
therefore, if you have your ion please send me a backup of OS asap.. (link where you can upload file of backup)
thanks in advance.

hello friends i have sony xperia ion
latest jelly bean software
root unlock
bootloader unlocked
debug off
unkown application on
i installed a software root switcher then choose the font then
software asked for reboot i pressed yes then it goes off
then sony loop is going on
so i hold the power off button + volume up for 3 vibration
after that my phone never goes on for 24 hour then i charged it then tried to installed kernel in fastboot mode i can see the new kernal when i start my phone but after writing sony it get freez
now my phone condition is when i charge it after some time in screen flash sony then get freez
i can do it soft reset 1 vibration but no hard reset 3 vibration
i dont have recovery and its custom jelly bean
and not getting into fastboot mode onlt flash mode for a while but without debug no success
so any one can help me
---------- Post added at 02:55 AM ---------- Previous post was at 02:07 AM ----------
well i did one thing in flash mood i reinstalled software lot of time because fast boot was not working
and after connecting to flash tool i hold the power button + volume up button then a window popup in flashtool to select ur phone then i click to my phone name and log say mobile doesnt reconize this action then i left my phone for some time connected my phone just turned on that means
i installed my software without debug in flash mood then in flashmood i softboot it holding power button + volume up and left it for some time connected in pc that was enough
so i fill lucky
---------- Post added at 03:05 AM ---------- Previous post was at 02:55 AM ----------
moiassar78 said:
Hello everybody , to all mates who bricked their phones by upgrading or using custom roms
I had soft brick my phone 3 times before and i read all soft brick methods here in our lovely forum, if u can my steps you will recover your phone 100%.
Note: remove your sd card and put it in PC and upload a custom rom in it, then bring it back to phone.
Lets go
1-]first of all these for unlocked boot loader.
2- after your phone die, connect to wall charger, at first will be no response (no red led) its OK don't be afraid.
3- charge it till red led on (it may takes many hours first time it need from me 22 hours, but usually need 10-15 hours).
4- now boot loops will start , its OK you are almost done believe me, prepare flash-tool in PC but do not select any thing.
5- while phone boot loop connect phone to your PC and do soft reset, ie hold power bottom and up volume bottom your phone will vibrate once now let power bottom and keep pushing up volume bottom (the phone is connected to PC as we said), blue led will appear which mean you are in fast-boot mode.
6- in flash tool select fast boot mode, a dialogue will appear select now (Select kernel To Flash), a window will appear choose from it JB_211_Kernel_twrp2.5.elf kernel or any CWM support kernel and flash it.
7- you will see the dialogue of flashing which till you that flashing is OK..
8 - now select reboot system from flash tool, your phone will restart.
9- enter recovery and select wipe all (advanced) system, data, cash and davlik cash, only leave internal memory and sd card
10- now select back and choose install and select any custom rom you have put in sd card and install it, after that select reboot system and you will go :laugh: its working believe me the phone will boot.
11- if you want to flash it with stock rom, after you boot recovery select power option and select power off (do not choose reboot) your phone will turn off, now prepare flash tool in PC and select your stock rom, wait till a pop up message appear to connect phone, connect your phone in flash mode ( volume down key and connect phone to PC) and flash stock rom .
Guys it really works do not ever give up try and try and you will recover your phone.
Please guys any one try this tell me the result I will help as I can.
Click to expand...
Click to collapse
thanks

Related

[Q] Stuck on sony logo

Hi,
My phone is stuck at sony logo, after install a custom rom (RomAur). I have locked BL, and I put my phone into fastboot mode and im tryng to fix it with flashtool (pc recognize the phone). Can I flash a rom in fastboot? it doesn´t work into flashmode. Any help? (As you can see im new in this topics...)
Did you try download stock ftf - run flashtool - choose the ftf, when ask for the phone ... push the off button for 5s (behind the phone next to sd slot), then put the phone in flash mode (vol. down) - connect your usb, phone should flash.
Sent from my C6506 using Tapatalk 2
Pablo256 said:
Hi,
My phone is stuck at sony logo, after install a custom rom (RomAur). I have locked BL, and I put my phone into fastboot mode and im tryng to fix it with flashtool (pc recognize the phone). Can I flash a rom in fastboot? it doesn´t work into flashmode. Any help? (As you can see im new in this topics...)
Click to expand...
Click to collapse
Every ZL/Z is meant to work in Flash Mode, just reset the phone by holding the OFF button on the back panel where the SD-card and SIM card are placed. Disconnect your phone from the computer, hold the OFF button until it vibrates THREE times (hold it for 3 seconds it vibrates twice (hard restart), hold for 5 it vibrates thrice(forced flashmode)) soon after plug in the phone into your computer (along with the proper drivers installed from Flashtool in (or wherever you installed it) C:/FlashTools/Drivers (these drivers are SOE-blah, ADB, and fast boot mainly located at the bottom.) Once you've accomplished this, head on over to the Android Development section download a FTF file and restore. If you wish to keep all your data try reinstalling RomAur with proper installation instructions, due to my lack of experience with that rom I cannot give you the best advice other than if you have CWM installed it's an option to constantly flash other roms/zips to possibly fix your scenario. Good luck!
I'll give you more details now, about my problem.
1.- My phone was OK (rooted and with CWM) running Hackit custom rom.
2.- I install RomAur, then on reboot the phone got stuck on sony logo (it means, sony logo, and then reboot, sony logo and then reboot, infinite loop). Pressing OFF button (back next to the SD) it restarts the phone but the infinite loop continues.
3.- I installed flashtool (drivers, etc)
4.- I run the phone and then pressing VOL DOWN and plugin the usb cable at the same time it puts on yellow light (i dont know what mode it is). Infinite loops stops, phone is off and battery charging icon is displayed.
5.- On yellow light then i disconnect the phone and then pressing VOL DOWN and reconnecting flashtool recognize it ("28/024/2013 20:24:13 - INFO - Device connected in flash mode"). No light on the phone. If i do the same but with VOL UP it runs fastboot (blue light).
6.-On flashmode, I press the flash device button (black beam icon), it ask for mode, i choose flashmode. Then i select the ftf. and flashtool displays
28/043/2013 20:43:29 - INFO - Preparing files for flashing
28/044/2013 20:44:07 - INFO - Device disconnected
And the infinite loop returns...
If i pressthe powe off button nothing happens, it vibrates only one time, every restart on the loop
HELP! and thanks for your answers
From your comments, get to your step 5. Meaning get your phone off. Run flashtool choose stock ftf when it asked for the phone. Holding Vol.Down plug in usb - this should reset your phone and get you going.
Sent from my C6506 using Tapatalk 2

[Q] Xperia Ion Lt28At Bootloop

Hello all.
I hate to post this, but I cannot find an answer anywhere. I've scoured the web for 4 days now, and cannot find an answer.
I have an Lt28at that had Cwm on it. I flashed a rom (which I later found out was a Jellybean rom) and needless to say, I'm in a bootloop.
I power on my phone, it displays the Sony logo, black screen, reboots back to the Sony logo, and so on. Cwm is gone, I've tried powering on while holding back, while holding Volume Down, while holding Volume Up, and even trying Cwm again.
I've read where people talk about flashmode, but I can't seem to get access to this if the Lt28at has it.
There seems to be no working method for me and I think I may have a paperweight.
If anyone happens to know what to do, I'm all ears.
Thanks!
~Preston556
I'm having the exact problem as you with the same phone. The thing is even when you hard reset the phone, when it starts charging again, eventually will start boot looping again and its impossible to put the ION in flashmode that way.
Can you take apart your phone and disconnect the battery from the mainboard? I just bought the tools for that I'm and waiting for them to ship. I don't think I'll have any luck for what I said before though.
What might actually works is charge the battery outside the phone (A ultra pain) and then use SEUS to recover the phone. I have not tried to see if SEUS recognizes my phone when it's boot looping. I will install Windows XP on a spare partition and try that out.
Will subscribe this thread, please help us people!
Try This
Dude,
I have bootlooped loads of phones in my time and its easy to sort out.
How to fastboot flash boot img
1) Download from XDA minimal fastboot and ADB drivers – from here http://forum.xda-developers.com/showthread.php?p=42407269
2) Install and run as admistrator – this will open a command window
3) Connect phone in fastboot mode, turn off the device, hold volume up and then connect your usb cable, the phone should he be in fastboot mode
4) In the command window enter the following – fastboot devices – this will show if your phone is connect by returning something like the image attached
5) Now you need to extract the boot img file from the rom you want to install, do this using winzip which can be downloaded from the internet.
6) You then need to open the location of your fastboot file and paste in the boot img file
7) Enter the following command into the command window – fastboot flash boot boot.img
8) Then use the command – fastboot reboot
9) Your phone should now boot up correctly with no error.
Our bootloaders are blocked thanks to AT&T, so that will be impossible! I cant even enter in fastboot mode
I see,
This is going to be tricky then, do either of you have a working recovery?
Is the phone recognised when connected via USB?
Sent from my Xperia S, made awesome by XDA.
It seems like no, just boot loops displaying the sony logo and thats all!
Hmmm,
ok this is the only other thing I got but its pretty hardcore.
First download flashtool and the latest Tft for your phone.
and the process goes like this !
1.open flashtool !*
2.turn off your phone and remove the battery !
3.click on the flash button on the flashtool.
4. at MODE SELECT --- select FLASHMODE --- click OK*
5. FIRMWARE SELECTION --- select SOURCE FOLDER ----- [....] will help u browse to the file location select it then !
6. WIPE ---check both WIPE DATA and WIPE CACHE
7. the click OK
8. After few sec it will ask for usb connection so PUT YOUR BATTERY BACK AND CONNECT YOUR PHONE TO COMPUTER BY PRESSING VOLUME DOWN BUTTON ON THE RIGHT !
9. wait till the process is over
10. unplug your device and wait it will take some time to boot up don't worry just stay calm*
Your phone should then be fully working
Sent from my Xperia S, made awesome by XDA.
Thanks alot for your help! I'm waiting for my tools to ship, i hope to get them by monday and do that, but unplugging the battery isn't the same as hard reseting the device?

[Guide] Soft unbrick/reflash stock firmware

DISCLAMER and WARNING: I'm not responsible for bricked devices, dead SD cards, thermonuclear war, or the current economic crisis. Please do some research if you have any concerns about this app.
Click to expand...
Click to collapse
Story:
Just received Sony Smartwatch 3 and decided to oem unlock for future so once root available I would not need to reset device.
Enabled adb
manually specified correct drivers in device manager
rebooted to bootloader using adb reboot bootloader
entered fastboot oem unlock twice and watch rebooted
but got stuck on boot for whatever reason.
I tried all the methods to get into fastboot (Swiping diagonal as on LG watch, and together with power button as on samsung ) to no avail.
The only other mode I was able to get into - s1 flash device w/o drivers.
Found Sony Emma software to work with unlocked Xperia, and after its installation it said that bootloader is locked and I need to either update from sony site or unlock bootloader first!
Installed Sony PC Companion software, but software update while listing smartwatch 3 said that there is no firmware for it.
After googling random forums on bootlooping sony xperias found that to reset device you need to click "repair my phone/tablet" in Phone/Tablet Software Update section
Click to expand...
Click to collapse
Guide to unbrick bootlooping SWR50 that is able to get into s1 bootloader/flash mode:
1. Power off device by holding power key until it reboots and then switches off with few vibrations
2. Connect to computer and check device manager - you should see unknown device
3. Install Sony PC Companion from this website http://www.sonymobile.com/us/tools/pc-companion/
Check if driver appeared in the Device Manager, e.g. unknown device will disappear and something like SEFLash will appear under usb controllers
If driver is still not found - try to install Emma (http://developer.sonymobile.com/services/flash-tool/) and get this driver to work
4. Go into PC Companion and click on "Support Zone", it will be downloaded
5. Then click on "Accessories software update" and try to update Smartwatch 3 (We might get new versions in the future, so it will be easiest to do so)
UPDATE: Now you can reflash from Accessories page, it will ask if you want to refrlash. Keeping steps bellow for information purposes.
6. If #5 not working:
Click on "Phone/Tablet Software Update" (yes, silly), click on "repair my phone/tablet", click Continue and Agree to all licenses, etc....
7. Once presented by the list of phones - Select anything I guess, but I selected Xperia Z2, it should start downloading and then updating.
8. Once done it will say build number watch was flashed, in my case it was KNX01V
9. Disconnect watch and boot it.
P.S. I guess they show phone selection just to provide instructions how to get into download mode and then flash based on the versions from bootloader.
P.P.S I'm glad I tried this last resort thing after being ready to deal with verizon support and waiting for new watch...
I've found that formatting cache and userdata partition like it says in the link below makes the device boot as expected:
source.android.com -> /source/building-devices.html#unlocking-the-bootloader
(sorry for faulty link, new user)
Good to know, I decided to wait a bit as I was eager to play with new toy.
Will unlock tomorrow if it is still locked after Sony reset.
And looks like I would have to write my own apps to test GPS and sensors performance.
And the good news is fastboot state unlocked after stock reflash.
XorZone said:
manually specified correct drivers in device manager
Click to expand...
Click to collapse
Can you please elaborate on which driver you used to get access to the Smartwatch 3 via ADB? I am trying to use the latest google USB driver, but the device is showing up as offline listed under "adb devices". Just tried the latest ADB v1.0.32 and it seems the watch shows up as "unauthorized". Did you see an ADB notification on the watch that you had to accept, because I am not seeing anything like that.
NVM, it started working after I restarted adb server like 25 times...
Device offline usually is not about driver. But I hit on device and manually picked google-adb composite device
OK, bricked watch today with corrupted /system and boot process hanged with non responsive power button. Had to wait for discharge and it was pita to get into flashmode with enough juice, because after black screen charging it boots instead of going into kernel charging.
Anyway it is up and running and has ROOT now!
Will upload files and create guide as soon as I will be with good internet.
See my sig!
*delete*
*deleted*
Well, there are different levels of bootloaders
At least Sony s1 flash, fastboot, kernel...
To flash with PC companion you need to boot into s1 by powering off and then hold power and connect to USB once sony logo shown (you should see black screen with backlight on). Make sure you sit on PC companion update screen and that watch had enough juice.
With charging there are different levels of charging:
1. Battery dead
2. Boot loader charging (about 4 min from USB port) with black screen
3. Kernel charging either offline (if you powered off before) or boot and operational charging.
When #2 charges it will boot kernel and if kernel or system is broken it might hang and discharge.
But you can force into s1 flash mode before it boots into kernel. Or if you lucky you could power on and power off before it boots and hang.
In my case I had not enough juice to flash it and watch didn't react to button in kernel mode, so I had to wait for discharge, then plugged into USB and start timer, figured it boots after ~3min 55sec. So I opened PC companion update screen, waited 3:53 and disconnected watch, then hold power button and connect to PC after 5 sec and was able to flash.
To power off - just hold power button until it reboots and continue holding until it vibrates 3 times.
Good luck
XorZone said:
Story:
Guide to unbrick bootlooping SWR50 that is able to get into s1 bootloader/flash mode:
1. Power off device by holding power key until it reboots and then switches off with few vibrations
2. Connect to computer and check device manager - you should see unknown device
3. Install Sony PC Companion from this website http://www.sonymobile.com/us/tools/pc-companion/
Check if driver appeared in the Device Manager, e.g. unknown device will disappear and something like SEFLash will appear under usb controllers
If driver is still not found - try to install Emma (http://developer.sonymobile.com/services/flash-tool/) and get this driver to work
4. Go into PC Companion and click on "Support Zone", it will be downloaded
5. Then click on "Accessories software update" and try to update Smartwatch 3 (We might get new versions in the future, so it will be easiest to do so)
UPDATE: Now you can reflash from Accessories page, it will ask if you want to refrlash. Keeping steps bellow for information purposes.
6. If #5 not working:
Click on "Phone/Tablet Software Update" (yes, silly), click on "repair my phone/tablet", click Continue and Agree to all licenses, etc....
7. Once presented by the list of phones - Select anything I guess, but I selected Xperia Z2, it should start downloading and then updating.
8. Once done it will say build number watch was flashed, in my case it was KNX01V
9. Disconnect watch and boot it.
P.S. I guess they show phone selection just to provide instructions how to get into download mode and then flash based on the versions from bootloader.
P.P.S I'm glad I tried this last resort thing after being ready to deal with verizon support and waiting for new watch...
Click to expand...
Click to collapse
This method is windows only. Is there no cross-platform way to do it?
I did the stupid thing.. and ended up with a softbricked phone.
Sony PC Companion did the trick for me!
I tried doing it through VMWare on my macbook, but didn't seem to work at all.
On windows it was plug'n'Pray
Sony companion will not let me restore my SW50. Detects it and tells me that the software is updated. If I try from the menu to repair phone, it makes me accept all agreements and finally tells me the same thing no updates.
Is in bootloop and do not start after open bootloader
My sw3 is in bootloop.I uesd your guide but still can't repair my watch. I tried many time to use pc companion but always got the same wrong message,wrong code(100) which couldn't connect to the Internet.
@swidon @KONG8691
I find myself in the same situation, you have found a solution to the problem?
Thanks for your help
best regards
jerry_italia said:
@swidon @KONG8691
I find myself in the same situation, you have found a solution to the problem?
Thanks for your help
best regards
Click to expand...
Click to collapse
Yes!, follow these instructions and you can enter in fastboot or recovery and flash a new firmware:
Detach any USB cable connected to the watch
Turn it off holding the power button and keep holding the button until the watch vibrates three times and then switches it off
Press the power button and keep holding. A blue screen that prompts to insert an USB cable will display
Double tap the power button
A black menu will display, with on-screen instructions
Move to Fastboot or Recovery Mode pressing the power button, once a time
Select Fastboot (or Recovery) by double pressing the power button
Good luck bro.
swidon said:
Yes!, follow these instructions and you can enter in fastboot or recovery and flash a new firmware:
Detach any USB cable connected to the watch
Turn it off holding the power button and keep holding the button until the watch vibrates three times and then switches it off
Press the power button and keep holding. A blue screen that prompts to insert an USB cable will display
Double tap the power button
A black menu will display, with on-screen instructions
Move to Fastboot or Recovery Mode pressing the power button, once a time
Select Fastboot (or Recovery) by double pressing the power button
Good luck bro.
Click to expand...
Click to collapse
you are my hero... stock recovery flashed and sw3 reboot! thankyou so much bro
jerry_italia said:
you are my hero... stock recovery flashed and sw3 reboot! thankyou so much bro
Click to expand...
Click to collapse
How do you go about getting stock recovery back at the moment I'm on 5.0.1 and I can't ota update to 5.1.1 because it thinks its on 5.1.1 when it's not the only way I can think of updating it is to get stock recovery then sideload the ota zip on stock recovert but I can't do that with TWRP can someone help?
Hi,
My watch boot loops on the marshmelow boot animation after I Got marshmelow
I tried XorZone instractions and it said it re-updated image. but it will boot looped.
I tried to factory reset from the menu (double tap at download screen then go factory reset).... didn't work. still boot loops.
I see I can go to fastboot or recovery, but what do I do there? Any instructions I can follow to try to revive my watch please? thanks.
wonderfull!
XorZone said:
Well, there are different levels of bootloaders
At least Sony s1 flash, fastboot, kernel...
To flash with PC companion you need to boot into s1 by powering off and then hold power and connect to USB once sony logo shown (you should see black screen with backlight on). Make sure you sit on PC companion update screen and that watch had enough juice.
With charging there are different levels of charging:
1. Battery dead
2. Boot loader charging (about 4 min from USB port) with black screen
3. Kernel charging either offline (if you powered off before) or boot and operational charging.
When #2 charges it will boot kernel and if kernel or system is broken it might hang and discharge.
But you can force into s1 flash mode before it boots into kernel. Or if you lucky you could power on and power off before it boots and hang.
In my case I had not enough juice to flash it and watch didn't react to button in kernel mode, so I had to wait for discharge, then plugged into USB and start timer, figured it boots after ~3min 55sec. So I opened PC companion update screen, waited 3:53 and disconnected watch, then hold power button and connect to PC after 5 sec and was able to flash.
To power off - just hold power button until it reboots and continue holding until it vibrates 3 times.
Good luck
Click to expand...
Click to collapse

OTA Update Elephone P8000 stucks at Boot Logo

Hi there,
I just updated P8000 via OTA update and after downloading the Update, the phone restarted and stops at the elephone boot Logo (about 30 min )!!
I did 5 Restarts but every time it hangs at the boot logo...
In the past i did no other updates or flashing ROMS.. nothing!
When i press "Volume Up" and "Power" to Start, i get three Options:
Recovery Mode
Fastboot Mode
Normal Boot
Using Recovery Mode leads to: Symbol Android Robot with "No Order" (in german : "Kein Befehl")
Using Fastboot Mode leads to: Nothing (Recovery Menue stays)
Using Normal Boot leads to: restart and hanging at Elephone Boot Logo
So, I am running out of Options... any ideas?
Cheers, Albert
Same. I tried using the official instructions to flash the stock rom but the SP flash tool stops responding after download button is pressed
a.cid said:
Same. I tried using the official instructions to flash the stock rom but the SP flash tool stops responding after download button is pressed
Click to expand...
Click to collapse
The Hardware of P8000 is pretty cool, but the Software is "§$§"%§""!$%
When you go to recovery mode and get the the android robot symbol. Press again Vol up + Power until you enter to recovery. Make a 3 wipe (data factory , cache and dalvink). Reboot and uninstall the El loader. Use another Loader instead of El Loader
i had the same problem. (in English NO COMMAND) I only flash Eragon ROM again. Sometimes you have to repeate.
AL 6677 - ELEPHONE MUST BE TURN-OFF !!!!!!! and CONNECT USB CABLE REPEATEDLY !!!
After that everything goes according to instructions
https://translate.google.at/transla...-p8000-rooten-und-flashen/&edit-text=&act=url
same problem since OTA my phone is bricked and cant unbrick
neonero said:
When you go to recovery mode and get the the android robot symbol. Press again Vol up + Power until you enter to recovery. Make a 3 wipe (data factory , cache and dalvink). Reboot and uninstall the El loader. Use another Loader instead of El Loader
Click to expand...
Click to collapse
THX a lot, I found only the 2 Options to wipe data factory and cache....... dalvink was not displayed in the menue (screenshot attached)
How to uninstall the EL Loader ?
showshow747 said:
i had the same problem. (in English NO COMMAND) I only flash Eragon ROM again. Sometimes you have to repeate.
AL 6677 - ELEPHONE MUST BE TURN-OFF !!!!!!! and CONNECT USB CABLE REPEATEDLY !!!
After that everything goes according to instructions
THX, I will try to flash Eragon, CM 12.1 is still not available, isn't it?
Click to expand...
Click to collapse
No CM 12.1 is not available yet.
In order to uninstall EI Loader, install first root (superSU), then install ccleaner and you can uninstall EI Loader (In system app)
Hi there, sorry for the revival !
But i got the same problem: OTA update, fail, P8000 blocked on boot screen.
I tried wipe data/factory reset + wipe cache -> nothing changed, still boot screen blocked...
Then, i tried to use flash tool, but, the phone isn't booting, so my pc isn't recognizing the phone..
I'm not even sure that I correctly installed the drivers..
Can i use flash tool even if the phone is blocked to boot screen?
I downloaded this ROM: stock-rom-elephone-p8000-20150907-android-5-1 (this is my first post i can't post URL..)
Because i got some issues with my phone and support told me to try it.
But when i follow the tutorial, launching "donwload" and connecting the phone, nothing happening..
The phone turn on, and display recharging logo, and flash tool still wainting.
Recovery mode -> "No command", Volume up + power is working, i used it to wipe datas
But at the moment, i'm still blocked, since 2 days, i dont know what to do
Can someone help me?
Thank you by advance, i hope my english isn't so bad
Zywoon said:
Hi there, sorry for the revival !
But i got the same problem: OTA update, fail, P8000 blocked on boot screen.
I tried wipe data/factory reset + wipe cache -> nothing changed, still boot screen blocked...
Then, i tried to use flash tool, but, the phone isn't booting, so my pc isn't recognizing the phone..
I'm not even sure that I correctly installed the drivers..
Can i use flash tool even if the phone is blocked to boot screen?
I downloaded this ROM: stock-rom-elephone-p8000-20150907-android-5-1 (this is my first post i can't post URL..)
Because i got some issues with my phone and support told me to try it.
But when i follow the tutorial, launching "donwload" and connecting the phone, nothing happening..
The phone turn on, and display recharging logo, and flash tool still wainting.
Recovery mode -> "No command", Volume up + power is working, i used it to wipe datas
But at the moment, i'm still blocked, since 2 days, i dont know what to do
Can someone help me?
Thank you by advance, i hope my english isn't so bad
Click to expand...
Click to collapse
Yes you can use SPFlash tool evenif the phone stucks in the boot screen. Simply switch the phone off, start SPFlash tool and then connect the phone to usb.
If you follow the instructions from elephone, then your phone should working again: http://bbs.elephone.hk/thread-1037-1-1.html#.VofQ13wvdpo
Cheers
Hi, and thx for the help.
The driver is correctly installed now, i had to allow unsigned drivers in windows parameters.
So, i followed the tutorial, again.
I configured SP flash tool, clicked download, and then connected powered off P8000 with USB.
But, again, the phone displays recharging logo, and flash tool still waiting...
The phone is recharging so the USB is working, so i don't know how to make my PC detect the phone......
Is there a way or a thing that i missed?
thank you..
EDIT: i finally got a timeout error from flashtool..
I missed something, but what !? i can't remove P8000 battery, is there somthing to do to get it detected by windows?
Like a boot mode, or a magic formula... i'm open
For MTK Driver installation:
Did you follow skeletons Guide? http://forum.xda-developers.com/elephone-p8000/help/guide-windows-10-mtk-vcom-usb-drivers-t3264884
I'm sorry to say, that I do not have any experience with windows installation, this problem, because SPFlash tool performes on my 64bit Linux very well, without any driver trouble.
Cheers
Hi,
I'm on windows 8.
I used SP_driver_v2.0, that is an .exe
it's the only driver tips gived in most of tutorial
I allowed unsigned drivers installation, and i correctly installed it.
I tried too use flashtool before and after restarting the PC-> no changes
Flashtool doesnt detect the phone
I start getting crazy..
I have repaired mine, so i'll share
Al6677 said:
Hi there,
I just updated P8000 via OTA update and after downloading the Update, the phone restarted and stops at the elephone boot Logo (about 30 min )!!
I did 5 Restarts but every time it hangs at the boot logo...
In the past i did no other updates or flashing ROMS.. nothing!
When i press "Volume Up" and "Power" to Start, i get three Options:
Recovery Mode
Fastboot Mode
Normal Boot
Using Recovery Mode leads to: Symbol Android Robot with "No Order" (in german : "Kein Befehl")
Using Fastboot Mode leads to: Nothing (Recovery Menue stays)
Using Normal Boot leads to: restart and hanging at Elephone Boot Logo
So, I am running out of Options... any ideas?
Cheers, Albert
Click to expand...
Click to collapse
So the simple way to solve it is flashing the latest stock elephone p8000 ROM, which you can find on google easly
1. as described on other forums, you have to install the adnroid drivers, then get the sp flash tool, and have an un-zipped stock elephone p8000 ROM.
2. if you are stuck at bootloop, do the following to power off the phone so you can flash the ROM
1. Long press power button until power off
2.Do it fast--Press volume Up and then hold power button
3. choose recovery (volume up choose menu, volume down enter)
4. android logo with red triangle is displayed( "no command")
5. hold power button and press volume up
You're in recovery mode
3. select power off
4. open the SP flash tool >go to download tab>opne "scatter loading"( you will find it in the Folder where you unzipped the stock elephone p8000 ROM, if you have more folders there, chose "firmware" folder)
5. on the left side, under scatter loading, you will find a "pull-down" tab - it will be written "download" chose "firmware upgrade" or "upgrade"
6. start the process, then connect your elephone p8000 (it must be powere off) via usb cable to the PC, the process will start,and in less then 5 Minutes you have a factory new Elephone p8000 with the latest good update
7. WATCH OUT- it will erase all your data, absolutely all your data on the phone, except SIM and SD card.
Hope it helped, if not, feel free to ask me =)
Hello,
I have similar problem. Bought P8000 5 days ago. Did update today. Bricked. Stuck at logo ... I tried to flash but SP flush tool but the process isn't starting. When I downloaded ROM I received long list as on the screenshot: kaczorowscy.name/Screenshot.png
I have ubuntu - I see lsusb and dmesg see the phone (it is shut down from recovery menu) but maybe I am missing something ....
Ok here is what id did:
1. Get SP flashtool
2. get newest stock ROM
3. Shut down phone through android recovery menu (start phone with holding volume up, select recovery mode, wait for dead android, hold volume up and unblock button for 3 sec.)
4. Open SP flashtool - use "format all + download" of ROM (unzip and select scatter file from rom) - click start
5. Connect shut downed phone
6. Dot OK! from flashtool
PS. Flashing removed IMEIs - they are both written on the battery - you need to use android service menu to check them with special codes and reboot the phone.
Thanks ALL! :good:
Fix - Recovery Mode
Al6677 said:
Hi there,
I just updated P8000 via OTA update and after downloading the Update, the phone restarted and stops at the elephone boot Logo (about 30 min )!!
I did 5 Restarts but every time it hangs at the boot logo...
In the past i did no other updates or flashing ROMS.. nothing!
When i press "Volume Up" and "Power" to Start, i get three Options:
Recovery Mode
Fastboot Mode
Normal Boot
Using Recovery Mode leads to: Symbol Android Robot with "No Order" (in german : "Kein Befehl")
Using Fastboot Mode leads to: Nothing (Recovery Menue stays)
Using Normal Boot leads to: restart and hanging at Elephone Boot Logo
So, I am running out of Options... any ideas?
Cheers, Albert
Click to expand...
Click to collapse
When I was trying to root my p8000 I couldn't flash a custom recovery, fortunately I discovered that to access recovery on stock android you need to go to the screen with the android and "no command"/"no order" text and hold down Vol+Up and Power for 3~ seconds and then release power, this will boot you into recovery mode, If wiping cache/factory reset isn't enough "fastboot flash recovery <image>.img" SHOULD work now
hope this helped

problem in rebooting device

hi every one i have a problem with my phone xz2c ... when i want it reboot he shut down and wont wake up untill i put it in charge and the same thing when i shut it down wont power on even i try all key power key +down or +up wont power on like i said untill i put it in charge :crying: :crying:
BUT when i reboot it with fasboot command (fastboot reboot) he reboot
i do a full wipe and fresh flash with flashtool and newflasher nothing help :crying: :crying: :crying:
my device still on stock firmware and not unlocked bootloader so any help for that???? and thank you....sorry for my bad english
Hi, unfortunately I have the same problem and experience with my XZ2C with locked bootloader and latest PIE fw *. 163. I did not notice that before.
I also did not find anything, what could help. I wiped and reflashed phone, it was useless and waste of time.
I also noticed, that I'm not able to start the phone when connected to PC, it starts directly in flash mode (same as POWER + vol Down). And there is no graphics in this mode also... I think, I had to select something in the 'menu' with blue (?) background to be able to flash ROM previously...
Another 'great' update from Sony?
I hope they will fix it in next (bootloader) update.
rSG1t said:
Hi, unfortunately I have the same problem and experience with my XZ2C with locked bootloader and latest PIE fw *. 163. I did not notice that before.
I also did not find anything, what could help. I wiped and reflashed phone, it was useless and waste of time.
I also noticed, that I'm not able to start the phone when connected to PC, it starts directly in flash mode (same as POWER + vol Down). And there is no graphics in this mode also... I think, I had to select something in the 'menu' with blue (?) background to be able to flash ROM previously...
Another 'great' update from Sony?
I hope they will fix it in next (bootloader) update.
Click to expand...
Click to collapse
did you fix the problem mine still same prolem???
not able to power on untill connect charger
no reboot untill put charger
when connect it to the PC (when it power OFF) he entre to fastboot mode directly without push any button
any help in here please :crying::crying::crying:

Categories

Resources