Guys from the TechMatte kindly provided me a Qi wireless charger (currently on sale, $24.99 with free shipping) for tests and review.
I'll go step by step to review this charger.
1. Packaging is very nice (especially compared with a few "noname" qi-chargers from the Chinese ebay sellers). Charger came with power supply, cable and simple documentation.
2. Charger made of the good (by haptics feelings) plastic (it's a really nice to touch - I'm not kidding). It's lightweight but not a slippery so it's good for the night stand.
3. The power cable is bit thick and may be a little short but it's OK (actually you may use any standard cable, if you want)
4. Charging: 'cause this charger has just one standard coil and detection sensor, you should put your N7 very accurately to start charging. I've got best result by putting my Nexus 7 as on picture.
Fortunately, charger has a nice feature: it makes a very light "beep" when start charging, so you may adjust your Nexus by listening.
Charger also has a tiny light diode (red: standby, white: charging). It's visible but very small and not annoying (even at night time).
I've successfully charged my N7 (2013) with Poetic Slimline case (as shown on picture). Charging rate is a little slower than using Nokia's DT-900 (but DT-900 has a 3 charging coils).
A few words about TechMatte company: these guys are well aware of their products (that they sell); they can consider customer's opinion and suggestions. Hope to see a special "tablet super Qi-charger" from the TechMatte soon...
So, my conclusion:
pros
- good, non-expensive product shipped from the local (US) company; shipping is fast!
- charger has a nice features: non-annoying audio- & light notifications; good plastic case;
cons
- charging area isn't large enough for N7 (IMHO), you should develop a habit to put your N7 properly from the first try.
is it only for nexus 4
Hmm, did you read my post and have seen my pictures? I'm charging my Nexus 7 on it
It's the Nexus that makes the beep, not the charger. Mine is the cheap Chinese one with no leds, and the Nexus beeps when the charging is initiated.
It fully charges my Nexus 7 over night.
Nope, wrong Both, charger and N7 making the beep. Charger makes beep when it detects qi-receiver (on start charging process); Nexus 7 makes notification sound (btw, I already changed that default annoying sound - you need root for this).
P.S. I had two cheap Chinese chargers (as an add-ons to my bunch of DT-900 plus new TechMatte's); one sent back because of diodes are too big and bright; second stopped working after three weeks (fortunately seller will send me a replacement for free - right after opening case on ebay ) So, I'll stay away from the cheap noname Chinese chargers - finally they costs too much for me
sensboston said:
Guys from the TechMatte kindly provided me a Qi wireless charger (currently on sale, $24.99 with free shipping) for tests and review.
I'll go step by step to review this charger.
1. Packaging is very nice (especially compared with a few "noname" qi-chargers from the Chinese ebay sellers). Charger came with power supply, cable and simple documentation.
2. Charger made of the good (by haptics feelings) plastic (it's a really nice to touch - I'm not kidding). It's lightweight but not a slippery so it's good for the night stand.
3. The power cable is bit thick and may be a little short but it's OK (actually you may use any standard cable, if you want)
4. Charging: 'cause this charger has just one standard coil and detection sensor, you should put your N7 very accurately to start charging. I've got best result by putting my Nexus 7 as on picture.
Fortunately, charger has a nice feature: it makes a very light "beep" when start charging, so you may adjust your Nexus by listening.
Charger also has a tiny light diode (red: standby, white: charging). It's visible but very small and not annoying (even at night time).
I've successfully charged my N7 (2013) with Poetic Slimline case (as shown on picture). Charging rate is a little slower than using Nokia's DT-900 (but DT-900 has a 3 charging coils).
A few words about TechMatte company: these guys are well aware of their products (that they sell); they can consider customer's opinion and suggestions. Hope to see a special "tablet super Qi-charger" from the TechMatte soon...
So, my conclusion:
pros
- good, non-expensive product shipped from the local (US) company; shipping is fast!
- charger has a nice features: non-annoying audio- & light notifications; good plastic case;
cons
- charging area isn't large enough for N7 (IMHO), you should develop a habit to put your N7 properly from the first try.
Click to expand...
Click to collapse
Does this charger stop charging completely after a device is full (IE: is the device not full when you wake up)? Or does it continue charging and "topping off" so you wake up with a full device?
Related
Just found this while browsing wireless chargers and it looks pretty good. I've been looking for a qi charger that it also at an angle so that i can use my phone as a clock at my bedside. I didn't want to spend the $70 for the Vu angled charger and the nokia 910 i have heard some mixed reviews about. I'm not as handy with wood or 3D printing as some others on here but I sure can do a mean job at browsing thru amazon:good:'
I'd like to point out my 2 favorite things about this product. First is that it's at an angle to it lets me still view my phone while at my bedside or desk. Second is that they have put 3 charging coils inside(like the Vu) to allow for better charging when phone position would be funky or just not practical on most other Qi chargers.
well I haven't purchased it yet (due to funds) but if someone here on XDA has it then feel free to post your own pics and review.
http://amzn.com/B00GL618IU
zolo185 said:
Just found this while browsing wireless chargers and it looks pretty good. I've been looking for a qi charger that it also at an angle so that i can use my phone as a clock at my bedside. I didn't want to spend the $70 for the Vu angled charger and the nokia 910 i have heard some mixed reviews about. I'm not as handy with wood or 3D printing as some others on here but I sure can do a mean job at browsing thru amazon:good:'
I'd like to point out my 2 favorite things about this product. First is that it's at an angle to it lets me still view my phone while at my bedside or desk. Second is that they have put 3 charging coils inside(like the Vu) to allow for better charging when phone position would be funky or just not practical on most other Qi chargers.
well I haven't purchased it yet (due to funds) but if someone here on XDA has it then feel free to post your own pics and review.
http://amzn.com/B00GL618IU
Click to expand...
Click to collapse
Hi there!
I'm from Bombay, India and I just recieved delivery of the NIllkin Energy Stone this evening.
Although I did notice quite a few micro scratches to the border of the pad, they should really wrap it in plastic to avoid this.
Apart from that the time it takes to charge is really long when you compare it to you standard USB wall charger. I use a Nexus 5 with the Energy Stone and since it has 3 induction Coils it really will charge it from just about any angle you can think of it's not very fidgity which I absolutely Love!
It Looks the part with the bright Blue LEDs blazing in the background on the surface of the charging pad area(Indicating that the phone is indeed charging)
I'm still waiting to see the LEDs glow green which means the phone is fully charged. This could very well be a myth...
I had to pay the equivalent of $56 in my currency of Rupees when it actually only costs $39 on amazon!!!
All in all a good experience with this product since it's my first wireless charger ever so I'm pretty stoked about it!!!
IMHO you should go ahead and buy it no questions asked coz it works perfectly and looks proper wicked
I had the tilted wireless charger already (link bellow) but decided to get the official wireless charger as well.
http://forum.xda-developers.com/showthread.php?t=2611246
Of course its a lot better made then the Chinese charger but is it better in usability and charging speed?
With the Chinese charger I was using the stock nexus charger and cable because they are much better then the cables that came with the charger, more detail in the link bellow
http://forum.xda-developers.com/showpost.php?p=50254993&postcount=116
The info you need to know is that the OEM nexus charger and cable put out about 1000-1100mA while the same cable paired with a samsung 2a block was able to push past 1600mA but not keep it there, leveling out at 1200mA. The OEM block and cable with Chinese charger puts out between 650mA and 730mA
So how does the official Nexus charger compare?
Well to start I tested the new cable with the OEM block and it was putting out just over 1100mA, so we know the cable is better then the OEM cable. Then I tested the new cable with the block that comes with it and got a steady 1600mA and it didnt drop. Now the block itself doesn't say anything on it as to what it puts out, but the charger base says 1.8a, is that what the block puts out? Regardless the block is much better then the Samsung 2a block.
I don't use a case so the phone on the charger itself puts out only a little bit more then Chinese charger keeping a steady 768mA. Now it can drop below and above that number but it really likes 768mA. So while it does have a great cable and block, if all you care about is speed then charger itself is a little faster but not by much compared to the Chinese charger.
As far as usability, I cant get the nexus charger to miss. I can throw it on and it connects every time. With the Chinese one it didn't always connect and i had to make sure i got it in the right spot and make sure, even if I heard the noise, that it didn't disconnect and was actually charging. With the nexus charger I feel confident that the magnets are lining it up and it gets a good connection every time.
As and added bonus, I have heard a lot about how you could possibly charge while vertical attached to a wall. I decided to try this and I can attest that the weak link will be the charger holding the wall not the charger holding the phone, as long as you don't use a case like me. The magnets are more then strong enough to hold the phone vertically, in fact they are more then strong enough to hold it upside down, I tried! The pad that sticks to the surface is just as strong as I've been hearing as well. I literately just slapped it on the wall and then threw the phone up and its holding thus far. I have it only a few inches above my night stand and will update if it falls, but so far it has held up to me taking the phone off and on about 50 times with no issue. I'm not sure how it would hold up as a car mount, only because I don't know how the sticky part of the base would hold up to extreme hot and cold. I image it would probably fall, especially if completely vertical.
I would definitely recommend the Nexus charger over a Chinese one. I you have the $50 then its a no brainier, it was even a couple bucks cheaper then that on amazon and my prime membership got it here on Monday when i ordered on Saturday afternoon. If you only have $13 bucks and don't mind waiting 3 or more weeks then Chinese one charges almost as fast.
I too finally went from the orb to the new charger because I wanted a vertical mount. I'm blind as a bat with my contacts out and wanted to be able to see the time on my phone while in bed. With the orb, the angle was bad and my nightstand is taller than my mattress, making it hard to see. So I got the new charger, put it on the side of my nightstand and it's holding just fine. Holds the phone great too and now I can see the time on my phone. As long as you can get a smooth, flat surface, I don't see why mounting vertically would be an issue.
Sent from my Nexus 5 using XDA Premium 4 mobile app
just wanted to say, it did end up falling off the wall the 2nd night while charging, the charger from the wall, not the phone from the charger. A good sized piece of 3m double sided tape right in the middle of the charger fixed that and I've had no problems since.
Charger in use
Can you advise please if the Google charger cuts out once the phone has reached 100% or does it change to a trickle charge? Looking at some of the alternatives (e.g. on Amazon) I haven't found any that automatically cut out at 100% although a few mention about changing to a trickle charge. What's your experience in this regard?
S
[Nexus 5 about to be delivered]
I bought the official one and I must say that I'm very pleased with my purchase, Is there any apps which can detect the charging voltage so i may test my charger as well?
zubsz said:
I bought the official one and I must say that I'm very pleased with my purchase, Is there any apps which can detect the charging voltage so i may test my charger as well?
Click to expand...
Click to collapse
If you're root, can use Android tuner from play store!
Tapatalked with my Nexus5(aka the Hammerhead)
Hi guys,
I can see in the UK it costs £34.99 but how much is the delivery charge?
Thanks,
M
how long takes to make a fully charge?
xupthree60 said:
I had the tilted wireless charger already (link bellow) but decided to get the official wireless charger as well.
http://forum.xda-developers.com/showthread.php?t=2611246
Of course its a lot better made then the Chinese charger but is it better in usability and charging speed?
With the Chinese charger I was using the stock nexus charger and cable because they are much better then the cables that came with the charger, more detail in the link bellow
http://forum.xda-developers.com/showpost.php?p=50254993&postcount=116
The info you need to know is that the OEM nexus charger and cable put out about 1000-1100mA while the same cable paired with a samsung 2a block was able to push past 1600mA but not keep it there, leveling out at 1200mA. The OEM block and cable with Chinese charger puts out between 650mA and 730mA
So how does the official Nexus charger compare?
Well to start I tested the new cable with the OEM block and it was putting out just over 1100mA, so we know the cable is better then the OEM cable. Then I tested the new cable with the block that comes with it and got a steady 1600mA and it didnt drop. Now the block itself doesn't say anything on it as to what it puts out, but the charger base says 1.8a, is that what the block puts out? Regardless the block is much better then the Samsung 2a block.
I don't use a case so the phone on the charger itself puts out only a little bit more then Chinese charger keeping a steady 768mA. Now it can drop below and above that number but it really likes 768mA. So while it does have a great cable and block, if all you care about is speed then charger itself is a little faster but not by much compared to the Chinese charger.
As far as usability, I cant get the nexus charger to miss. I can throw it on and it connects every time. With the Chinese one it didn't always connect and i had to make sure i got it in the right spot and make sure, even if I heard the noise, that it didn't disconnect and was actually charging. With the nexus charger I feel confident that the magnets are lining it up and it gets a good connection every time.
As and added bonus, I have heard a lot about how you could possibly charge while vertical attached to a wall. I decided to try this and I can attest that the weak link will be the charger holding the wall not the charger holding the phone, as long as you don't use a case like me. The magnets are more then strong enough to hold the phone vertically, in fact they are more then strong enough to hold it upside down, I tried! The pad that sticks to the surface is just as strong as I've been hearing as well. I literately just slapped it on the wall and then threw the phone up and its holding thus far. I have it only a few inches above my night stand and will update if it falls, but so far it has held up to me taking the phone off and on about 50 times with no issue. I'm not sure how it would hold up as a car mount, only because I don't know how the sticky part of the base would hold up to extreme hot and cold. I image it would probably fall, especially if completely vertical.
I would definitely recommend the Nexus charger over a Chinese one. I you have the $50 then its a no brainier, it was even a couple bucks cheaper then that on amazon and my prime membership got it here on Monday when i ordered on Saturday afternoon. If you only have $13 bucks and don't mind waiting 3 or more weeks then Chinese one charges almost as fast.
Click to expand...
Click to collapse
Have you considered using this charger in the car? From what you're saying, the hold issue seems to be the charger itself. Using double sided 3m thick tape may solve the issue.
The reason I'm curious is because I and many other previous Palm Pre users used to use the touchstone wireless charger in their cars and the phone never fell of even on extreme bumps. It was great being able to simply place the Pre on the charger and if you were lucky you could put the touchstone right in your line of sight (I have an 06 civic so the touchstone fit right next to the steering wheel, to the right. Look at my profile pic or do a search for palm Pre wireless charging in the car and you'll come up with hundreds of results and pics).
Do you think the charger's internal magnets would be strong enough to hold the nexus 5 in place while driving? Right now, I still use the touchstone as a place holder for my 5 as the internal metal discs on the 5 line up nicely with the internal magnets in the touchstone. I did modify the touchstone slightly and added magnets every 90° starting at the 45° position and then the other 3 were 90°apart from the initial magnet. I'll try to post a pic or a video of what I mean. The touchstone is not a qi charger so it doesn't charge but it certainly makes for a super convenient spot for the phone to be especially when using navigation. Also the nexus has not fallen once while driving over some pretty harsh bumps.
What do you think?
Sent from my wondrous Nexus numeral 5
VOLTAGEROCK said:
Have you considered using this charger in the car? From what you're saying, the hold seems to be the charger itself. Using double sided 3m thick tape may solve the issue.
The reason I'm curious is because I and many other previous Palm Pre users used to use the touchstone wireless charger in their cars and the phone never fell of even on extreme bumps. It was great being able to simply place the Pre on the charger and if you were lucky you could put the touchstone right in your line of sight (I have an 06 civic so the touchstone fit right next to the steering wheel, to the right. Look at my profile pic or do a search for palm Pre wireless charging in the car and you'll come up with hundreds of results and pics).
Do you think the charger's internal magnets would be strong enough to hold the nexus 5 in place while driving? Right now, I still use the touchstone as a place holder for my 5 as the internal metal discs on the 5 line up nicely with the internal magnets in the touchstone. I did modify the touchstone slightly and added magnets every 90° starting at the 45° position and then the other 3 were 90°apart from the initial magnet. I'll try to post a pic or a video of what I mean. The touchstone is not a qi charger so it doesn't charge but it certainly makes for a super convenient spot for the phone to be especially when using navigation. Also the nexus has not fallen once while driving over some pretty harsh bumps.
What do you think?
Sent from my wondrous Nexus numeral 5
Click to expand...
Click to collapse
Been using the official Qi charger in the car daily, with this set up: http://forum.xda-developers.com/goo...es/kenu-airframe-n5-wireless-charger-t2573184. Perfect solution.
http://www.amazon.com/RAVPower®-Wir...F8&qid=1393455689&sr=8-3&keywords=ravpower+s3
After getting my Nexus 5 and getting spoiled with wireless charging, it was quite troublesome to charge via a usb cable when using my s3 as a secondary phone. So I wanted to get a wireless receiver to go along with the Nexus 5.
Packaging
Not much to talk about here, simple box containing the unit with a small plastic wrap inside. No frills.
Build Quality
The receiving tag is very thin, I can't compare it to others but im guessing they are all comparable. I had no problems putting the back cover on. There wasn't a huge bulge were the tag is. There is a slight bump but you would really have to be trying to feel for it to notice its even there.
Performace
Using my Ravpower Qi Charger it detected the tag instantly. There wasn't any time where I had trouble with getting the S3 to start charging. It didn't get any warmer than usual when charging with a usb cable.
I have a Diztronic case on my S3 and it charged it just fine through the case. I've tried other cases such as the ZooGue case had the same results.
Conclusion
For a mere 10 bucks, its sort of a no brainer for the convenience of wireless charging. I been using it for over 2 weeks and never had a problem with it.
You MUST have a wireless charging pad. Ravpower is offering a 20% discount on the receiving tag when you buy a charging pad with it via amazon. Details is under the "special offers" in the middle of the product page.
I recommend the Ravpower Orbit
Review of the Orbit here
http://forum.xda-developers.com/showthread.php?p=50243963
http://www.amazon.com/RAVPower®-Qi-...qid=1393456590&sr=8-1&keywords=ravpower+orbit
Note: I was provided a sample for an unbiased review
Do these guys make a Qi receiver for an S3?
krash183 said:
http://www.amazon.com/RAVPower®-Wir...F8&qid=1393455689&sr=8-3&keywords=ravpower+s3
After getting my Nexus 5 and getting spoiled with wireless charging, it was quite troublesome to charge via a usb cable when using my s3 as a secondary phone. So I wanted to get a wireless receiver to go along with the Nexus 5.
Packaging
Not much to talk about here, simple box containing the unit with a small plastic wrap inside. No frills.
Build Quality
The receiving tag is very thin, I can't compare it to others but im guessing they are all comparable. I had no problems putting the back cover on. There wasn't a huge bulge were the tag is. There is a slight bump but you would really have to be trying to feel for it to notice its even there.
Performace
Using my Ravpower Qi Charger it detected the tag instantly. There wasn't any time where I had trouble with getting the S3 to start charging. It didn't get any warmer than usual when charging with a usb cable.
I have a Diztronic case on my S3 and it charged it just fine through the case. I've tried other cases such as the ZooGue case had the same results.
Conclusion
For a mere 10 bucks, its sort of a no brainer for the convenience of wireless charging. I been using it for over 2 weeks and never had a problem with it.
You MUST have a wireless charging pad. Ravpower is offering a 20% discount on the receiving tag when you buy a charging pad with it via amazon. Details is under the "special offers" in the middle of the product page.
I recommend the Ravpower Orbit
Review of the Orbit here
http://forum.xda-developers.com/showthread.php?p=50243963
http://www.amazon.com/RAVPower®-Qi-...qid=1393456590&sr=8-1&keywords=ravpower+orbit
Note: I was provided a sample for an unbiased review
Click to expand...
Click to collapse
woneil said:
Do these guys make a Qi receiver for an S3?
Click to expand...
Click to collapse
Yeah they do but apparently they sold out of the s3. I imagine it'll come back in stock soon
Sent from my Nexus 5 using Tapatalk
The best deal for a wireless charging pad is from Monster Watts, sold through Vivealive (sp). $14.99, is the WiQiQi charging pad. They charge $5 shipping, first class USPS inside the US. The pad works well. Not much to look at though, but good deal for the $$..
I'm using the RavPower reciever. It works well together. What I have found out playing around with the charger, is that if you have a poor connection between the charger & reciever, you will get the on/off cycling. I have my phone in a Seidio Active case with velcro on the back to secure the phone on the Mountek CD slot car mount I use. The extra thickness of the velcro prevents good reception & I get the cycling. If I remove the plastic frame all is good. If I remove just the velcro all is good. The screen will flash once at charge start, turn off, then flash once when battery full, then turn back off. The phone will then remain on the pad in standby with no cycling.
It all works a treat, I can't wait to get my AirDock for the car to add wireless charging there as well.
Ravpower said it'd come back in stock within a week. Also, I don't have experience with any other Qi charging base, just ravpower and they've worked great for me
This is a review of Inateck's 36W 5-port USB Desktop Charger. http://www.inateck.com/inateck-uc5001-5-port-usb-family-sized-desktop-charger/
This is my first time with an Inateck product and my initial impression is Quality.
I received their new 5 port Smart USB charger and have spent about 1 1/2 weeks testing it and putting it through its paces. More on performance later. For now... Initial impressions:
The product arrived in a clean, easy to open, minimalist package. Under the outer sleeve is an unassuming, cardboard box, with a slide in type closure and bent/molded cardboard for packing.
The outer sleeve contains all the usual information:
The Packing:
Included:
My initial impression was both good and bad. The bad however, was quickly assuaged. The unit is relatively small, no doubt due to the transformer being in an external power supply. That was my initial "bad' feeling; the charger comes with a laptop style power supply:
At first I thought "UNGH! A laptop charger?!" but shortly I realized the genius of it. By not incorporating the transformer/converter in the unit itself, nor in the plug, give you a smaller more svelte desktop component and the plug fits in a crowded outlet and doesn't fall out due to its own weight.
The outside of the unit is plastic and includes an on/off button and a single blue LED. The LED lets you know the charger is on. This is a nifty light that lets you know it's powered, but really only would only be useful if you plugged your device in and it didn't charge. The charger has 3 1A charging ports and 2 2.1A ports. This configuration suggest it was designed more for Apple than Android since apple iPhones/iPods use 1A and iPads use 2.1... BUT they work well with android also. My phone (Nexus 4) uses 1.5 maximum amps for charging and charges in both the 1A and 2A ports, slower and faster respectively. Most android tablets are also 2.1 amp so the 2 higher ports work for them also.
I have charged my devices a few times and can say that this little beauty works as advertised. I have charged 5 items at once and it didn't even get hot! I charged my: iPod 4th gen, iPod 5th gen, Nexus 4 phone, Nexus 7 tablet and my Jaybird X Bluetooth headphones all at the same time and since my phone was on a 2.1A port all items charged within their normal charging limits.
One of the best features of this charger is that it doesn't have designated ports for certain items.. I can charge anything in any port (as long as the amperage agrees ) So I don't need to fuss over what goes where.
All in all the only complaint I have is a small one: I wish they'd used rubber feet on the bottom of the unit to prevent it sliding around, but since I can pick up a set of small rubber buttons for a buck at my home store, it's really not a big issue. I can definitively say that this Inateck 36W 5-port USB Desktop Charger is ONE of the BEST chargers I've ever used. I keep mine on my nightstand, and I can keep 5 devices charged and not need to unplug my alarm clock! :laugh:
They are on sale at Amazon right now also!
Questions & Comments are welcome, as always!
Reserved.
Sent from my Nexus 4 using Tapatalk
Ordered one, definitely a great choice for lots of charging ports at such price.
I was reading for a while through the various subforums here trying to catch some info on selecting the "best" qi charger for charging our devices here at home (N4, N5 + some others). Finally after reading this review I came to the conclusion that in terms of efficiency, power consumption and charging time more or less all qi chargers perform equal. There are some exceptions tho, like the Panasonic TM101 with it's moving coil or the Tylt VÜ. Both allow free positioning (more or less) of the devices.
I noticed that especially with a case on, proper alignment becomes very important. So you give up fiddling with tiny microUSB connectors but have to deal with aligning the phone to accquire efficient charging. So I wonder is there any affordable charger out there with multiple coils?
sebr said:
I was reading for a while through the various subforums here trying to catch some info on selecting the "best" qi charger for charging our devices here at home (N4, N5 + some others). Finally after reading this review I came to the conclusion that in terms of efficiency, power consumption and charging time more or less all qi chargers perform equal. There are some exceptions tho, like the Panasonic TM101 with it's moving coil or the Tylt VÜ. Both allow free positioning (more or less) of the devices.
I noticed that especially with a case on, proper alignment becomes very important. So you give up fiddling with tiny microUSB connectors but have to deal with aligning the phone to accquire efficient charging. So I wonder is there any affordable charger out there with multiple coils?
Click to expand...
Click to collapse
I have almost all the big names out there. I have the nexus 4 orb charger and the nexus 5 charger. The energizer and LG verizon branded one. I also have the Tylt Vu. Now I have the AirDock in the car.
To me multiple coils is a feature and not really required. The only one I have that has multiple coils is the Tylt Vu. Its good, but has a big footprint so that charger remains next to my alarm clock and LG G Watch charging set up. I have the LG verizon charger that my wife uses for the Nexus 4. and I use the Nexus 5 pad at work because that had the smallest footprint. I have used various cases with each of these chargers, including the airdock. From the Spigen Ultra Hybrid to the Nexus 4 replica bumper for the Nexus 5, they all work. Sure the Tylt can charge my phone horizontally, but that's it really. lol.
I guess to answer your question, the cheapest multi coil? Well even though this technically not a mulit coil, it does locate your coil for you on your qi compatible device. Pretty neat IMO.
Panasonic QE-TM101
http://www.ebay.com/sch/i.html?_from=R40&_sacat=0&_nkw=Panasonic+QE-TM101&_sop=15
Here's a cheapy tylt VU clone
http://www.dx.com/p/itian-a6-3-coil...let-pc-mobile-phone-black-325355#.U_O10EFaUTk
And here's a late addtion...the Nillkin 3 coil charger
http://www.ebay.com/itm/like/141370021990?lpid=82
Thanks for your answer. The Panasonic charger is, according to most reviews, not supporting trickle charging. If the device is charged completely the coil returns to initial position and the battery dicharges. In some cases there is also the charging coil repeatedly moving to the device and back to parking position again. Plus for some odd reason it is only available from Japan as direct import.
Tylt VU is way too overpriced, although the concept behind it seems great. Even the clone is too expensive.
So far the Nillkin Energy Stone looks good. Just cannot sind any serious reviews of it. Also only shipping from HK only which could be a problem due to strict german customs here