Develop Bugs

[WIP] Lets recover hard-bricks

Hey guys. I'm doing some work to figure out how to recover Galaxy Nexus devices which are hard-bricked.. ie.. they have a bad or no bootloader installed.
the boot sequence
1. IROM - the Internal ROM which cannot be rewritten on the device. This loads the XLoader.
2. XLoader/MLO - This completes the initialization of the processor and memory, and loads up the relatively huge U-Boot ( Samsung modified this and calls it SBL)
3. UBoot/SBL - This "Bootloader" is almost a complete operating system. The U-Boot initializes the screen, provides Odin mode, Fastboot Mode as well as loading the kernel/recovery and provides a UART debugging mode (Yet to be unlocked).
4. Kernel - Once we reach this point, it's all clear.. the kernel is linux which loads android and all sorts of other things.
The Problem
People are bricking their devices at stage 2 and 3 of this boot sequence... This leaves them unable to boot Fastboot or Odin. The device is 100% interchangable with a brick. These devices are ending up hard bricked.
The solution
We must come up with a way to undo the hard brick. Here are some things i'm looking at to use the native hardware to recover itself.
When you plug in the device (when off), you will immediately notice a Texas Instruments D010 device gets enumerated. This is a debug mode for the processor.
Code:
Bus 001 Device 023: ID 0451:d010 Texas Instruments, Inc.
We've started looking at some bootloader output here: http://forum.xda-developers.com/showthread.php?t=1461986
You can find information about the OMAP4 bootloaders here: http://omapedia.org/wiki/Bootloader_Project
Help
I need help locating drivers to initialize the 0451:d010 device and make it readable from within Linux or Windows.. Generally Linux is easier to find appropriate drivers.
I could use some help collecting more reading materials and resources.
I think together as a community we can take care of this problem.

I kinda forgot that thread, it got lost among rom/kernel threads. Thanks for the reminder.
sent from my i9250

Ok... so here's the most complete boot log I've been able to obtain from the device
Code:
[Thermal] OK to boot
Initialize runtime thermal monitoring ...done!
-- OMAP 00004460 (version 04460e11) PPA release 1.6.1 Hash 30639809--
Device type: HS, DEBUG OFF
CPFROM HAL API support integrated
THERMAL support integrated: Run Time + Boot time
HDCP support integrated
-- PROD PPA RC3.2.3 --
Reset reason = 00037ba2
PRM_RSTST = 00000002
PPA freed 2992 bytes
Texas Instruments X-Loader 1.41 (Nov 16 2011 - 16:28:45)
Starting OS Bootloader from MMC/SD1 ...
EXCEPTION : CM_CLKMODE_DPLL_ABE = 0x7
EXCEPTION : CM_IDLEST_DPLL_ABE = 0x1
EXCEPTION : CM_CLKSEL_DPLL_ABE = 0x804018
EXCEPTION : CM_CLKMODE_DPLL_CORE = 0xf
EXCEPTION : CM_IDLEST_DPLL_CORE = 0x1
EXCEPTION : CM_CLKSEL_DPLL_CORE = 0x7d05
EXCEPTION : CM_CLKMODE_DPLL_PER = 0x107
EXCEPTION : CM_IDLEST_DPLL_PER = 0x1
EXCEPTION : CM_CLKSEL_DPLL_PER = 0x1400
EXCEPTION : CM_CLKMODE_DPLL_MPU = 0x117
EXCEPTION : CM_IDLEST_DPLL_MPU = 0x1
EXCEPTION : CM_CLKSEL_DPLL_MPU = 0x807d07
CFG_LOADADDR = 0xa0208000
1st instruct = 0xEA000007
[ __omap_twl6030_init_vbat_cfg :49] SA_PHOENIX_START_CONDITION = 0x4a
[ __omap_twl6030_init_vbat_cfg :54] SA_PH_CFG_VBATLOWV = 0x80
[ __omap_twl6030_init_vbat_cfg :63] SA_PH_CFG_VBATLOWV = 0x80
[ __omap_twl6030_init_vbat_cfg :86] SA_BBSPOR_CFG = 0x78
====== VCELL : 381375, SOC : 49, nType : 5 ======
[Charger] nScaledVCELL : 381375000, nDesriedSOC, : 62, nMaxSOC : 82, nMinSOC : 42
[ omap_power_get_reset_source :47] PRM_RSTST : 0x2
[ __omap_usbacc_test_donwload_by_musb :280] nDeviceType : 0x5
[ omap_usbacc_get_reboot_reason :333] nJigStatus = 0x00000003
[ __sbl_board_hw_init_late :719] final reboot mode in cable = 0x40000
[ __sbl_board_hw_init_late :730] Wake up by TA / USB / JIG
* FB base addr = 0xbea70000!
* PANEL_S6E8AA0_ID_READ : 0x12, 0x8e, 0x9f.
[ omap_power_get_reset_source :47] PRM_RSTST : 0x2
dev : 5
[sbl_board_charger_init_post] : Succeed set model data : 0x78!!!!!
====== VCELL : 381500, SOC : 50, nType : 5 ======
[Charger] nScaledVCELL : 381500000, nDesriedSOC, : 62, nMaxSOC : 82, nMinSOC : 42
[ omap_power_get_reset_source :47] PRM_RSTST : 0x1
[ __omap_usbacc_test_donwload_by_musb :280] nDeviceType : 0x5
[ omap_usbacc_get_reboot_reason :333] nJigStatus = 0x00000003
[ __sbl_board_hw_init_late :719] final reboot mode in cable = 0x40000
[ __sbl_board_hw_init_late :730] Wake up by TA / USB / JIG
* FB base addr = 0xbea70000!
* PANEL_S6E8AA0_ID_READ : 0x12, 0x8e, 0x9f.
[ omap_power_get_reset_source :47] PRM_RSTST : 0x1
message.command =
message.status =
message.recovery =
<hit enter twice to activate fiq debugger>
[Thermal] OK to boot
Initialize runtime thermal monitoring ...done!
-- OMAP 00004460 (version 04460e11) PPA release 1.6.1 Hash 30639809--
Device type: HS, DEBUG OFF
CPFROM HAL API support integrated
THERMAL support integrated: Run Time + Boot time
HDCP support integrated
-- PROD PPA RC3.2.3 --
Reset reason = 0003fba2
PRM_RSTST = 00000002
PPA freed 2992 bytes
Texas Instruments X-Loader 1.41 (Nov 16 2011 - 16:28:45)
Starting OS Bootloader from MMC/SD1 ...
EXCEPTION : CM_CLKMODE_DPLL_ABE = 0x7
EXCEPTION : CM_IDLEST_DPLL_ABE = 0x1
EXCEPTION : CM_CLKSEL_DPLL_ABE = 0x804018
EXCEPTION : CM_CLKMODE_DPLL_CORE = 0xf
EXCEPTION : CM_IDLEST_DPLL_CORE = 0x1
EXCEPTION : CM_CLKSEL_DPLL_CORE = 0x7d05
EXCEPTION : CM_CLKMODE_DPLL_PER = 0x107
EXCEPTION : CM_IDLEST_DPLL_PER = 0x1
EXCEPTION : CM_CLKSEL_DPLL_PER = 0x1400
EXCEPTION : CM_CLKMODE_DPLL_MPU = 0x117
EXCEPTION : CM_IDLEST_DPLL_MPU = 0x1
EXCEPTION : CM_CLKSEL_DPLL_MPU = 0x807d07
CFG_LOADADDR = 0xa0208000
1st instruct = 0xEA000007
[ __omap_twl6030_init_vbat_cfg :49] SA_PHOENIX_START_CONDITION = 0x8
[ __omap_twl6030_init_vbat_cfg :54] SA_PH_CFG_VBATLOWV = 0x80
[ __omap_twl6030_init_vbat_cfg :63] SA_PH_CFG_VBATLOWV = 0x80
[ __omap_twl6030_init_vbat_cfg :86] SA_BBSPOR_CFG = 0x78
====== VCELL : 381375, SOC : 50, nType : 5 ======
[Charger] nScaledVCELL : 381375000, nDesriedSOC, : 62, nMaxSOC : 82, nMinSOC : 42
[ omap_power_get_reset_source :47] PRM_RSTST : 0x2
[ __omap_usbacc_test_donwload_by_musb :280] nDeviceType : 0x5
[ omap_usbacc_get_reboot_reason :333] nJigStatus = 0x00000003
[ __sbl_board_hw_init_late :719] final reboot mode in cable = 0x40000
[ __sbl_board_hw_init_late :730] Wake up by TA / USB / JIG
* FB base addr = 0xbea70000!
* PANEL_S6E8AA0_ID_READ : 0x12, 0x8e, 0x9f.
[ omap_power_get_reset_source :47] PRM_RSTST : 0x2
<hit enter twice to activate fiq debugger>
Communications established====== VCELL : 381375, SOC : 50, nType : 5 ======
[Charger] nScaledVCELL : 381375000, nDesriedSOC, : 62, nMaxSOC : 82, nMinSOC : 42
* FB base addr = 0xbea70000!
* PANEL_S6E8AA0_ID_READ : 0x12, 0x8e, 0x9f.
[ omap_power_get_reset_source :47] PRM_RSTST : 0x2
<hit enter twice to activate fiq debugger>
debug> console
console mode
[ 3.320373] cannot apply mgr(lcd) on inactive device
[ 3.325805] omapfb omapfb: failed to apply dispc config
[ 3.331359] cannot apply mgr(tv) on inactive device
[ 3.336578] omapfb omapfb: failed to apply dispc config
[ 3.341949] cannot apply mgr(lcd2) on inactive device
[ 3.347167] omapfb omapfb: failed to apply dispc config
[ 3.354888] regulator_init_complete: VDAC: disabling
[ 3.361053] omaplfb OMAPLFBInitFBDev: Device 0: Requesting 4 TILER 2D framebuffers
[ 3.369232] ## wifi_probe
[ 3.371917] wifi_set_power = 1
[ 3.631866] wifi_set_carddetect = 1
[ 3.647338]
[ 3.647338] Dongle Host Driver, version 5.90.125.94
[ 3.647338] Compiled in drivers/net/wireless/bcmdhd on Nov 21 2011 at 19:05:54
[ 3.764984] mmc1: queuing unknown CIS tuple 0x80 (7 bytes)
[ 3.817810] mmc1: queuing unknown CIS tuple 0x80 (3 bytes)
[ 3.837463] mmc1: new high speed SDIO card at address 0001
[ 3.844818] F1 signature read @0x18000000=0x16844330
[ 3.859436] DHD: dongle ram size is set to 294912(orig 294912)
[ 3.866546] wl_create_event_handler thr:5b started
[ 3.871673] dhd_attach thr:5c started
[ 3.875488] dhd_attach thr:5d started
[ 3.879272] dhd_attach thr:5e started
[ 3.883148] wifi_get_mac_addr
[ 3.888519] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
[ 3.897430] wifi_set_power = 0
[ 4.157012] =========== WLAN placed in RESET ========
[ 4.163116] fsa9480 4-0025: cable detect change, from 'unknown/none' to 'uart'
[ 4.171203] twl_rtc twl_rtc: setting system clock to 2012-05-13 00:25:12 UTC (1336868712)
[ 4.180816] Freeing init memory: 276K
[ 4.187561] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[ 4.214172] max17040 4-0036: online = 1 vcell = 3795000 soc = 48 status = 3 health = 1 temp = 330 charger status = 0
[ 4.288116] keychord: using input dev tuna-gpio-keypad for fevent
[ 4.354614] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: (null)
[ 4.446746] mms_ts 3-0048: fw version 0x62 already present
[ 4.454498] mms_ts 3-0048: Melfas MMS-series touch controller initialized
[ 4.757202] omap-rproc omap-rproc.1: Loaded BIOS image ducati-m3.bin, size 4489868
[ 4.765838] omap-rproc omap-rproc.1: BIOS image version is 2
[ 4.785888] omap-iommu omap-iommu.0: iommu_get: ducati qos_request
[ 4.806243] omap_hwmod: ipu: failed to hardreset
[ 4.811035] omap-iommu omap-iommu.0: ducati: version 2.1
[ 4.822448] omap-rproc omap-rproc.1: remote processor ipu is now up
[ 4.835571] omap_rpmsg_mbox_callback: received echo reply from ipu !
[ 4.842071] omap_rpmsg_mbox_callback: received echo reply from ipu !
[ 4.848541] omap_rpmsg_mbox_callback: received echo reply from ipu !
[ 4.855072] omap_rpmsg_mbox_callback: received echo reply from ipu !
[ 4.861816] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x32
[ 4.869812] virtio_rpmsg_bus virtio0: creating channel rpmsg-client-sample addr 0x33
[ 4.877899] virtio_rpmsg_bus virtio0: creating channel rpmsg-omx addr 0x3c
[ 4.885192] rpmsg_omx rpmsg-omx0: new OMX connection srv channel: 1024 -> 60!
[ 5.959960] EXT4-fs (mmcblk0p12): recovery complete
[ 5.974639] EXT4-fs (mmcblk0p12): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 6.021484] virtio_rpmsg_bus virtio1: creating channel rpmsg-omx addr 0x3c
[ 6.029602] rpmsg_omx rpmsg-omx1: new OMX connection srv channel: 1024 -> 60!
[ 6.170227] EXT4-fs (mmcblk0p11): recovery complete
[ 6.178833] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: nomblk_io_submit,errors=panic
[ 6.199371] EXT4-fs (mmcblk0p3): mounted filesystem with ordered data mode. Opts: (null)
[ 6.269744] android_usb: already disabled
[ 6.274810] mtp_bind_config
[ 6.277740] adb_bind_config
[ 6.297790] HDCP: loaded keys
[ 6.481079] warning: `adbd' uses 32-bit capabilities (legacy support in use)
[ 6.488433] adb_open
[ 6.702026] init: sys_prop: permission denied uid:1001 name:net.rmnet1.dns1
[ 6.709808] init: sys_prop: permission denied uid:1001 name:net.rmnet1.dns2
[ 6.718780] init: sys_prop: permission denied uid:1001 name:net.rmnet1.gw
[ 6.726196] init: sys_prop: permission denied uid:1001 name:net.rmnet2.dns1
[ 6.733612] init: sys_prop: permission denied uid:1001 name:net.rmnet2.dns2
[ 6.741455] init: sys_prop: permission denied uid:1001 name:net.rmnet2.gw
[ 6.749481] PVR: Installing MISR with cookie c0800c2c
[ 6.757415] PVR: Installing device LISR SGX ISR on IRQ 53 with cookie c7aa2700
[ 6.766174] PVR: OSUnMapPhysToLin: unmapping 65535 bytes from c8be0000
[ 6.773162] PVR: SysFinalise: Version string: SGX revision = 1.2.0
[ 6.797027] [MODEM_IF] misc_open : umts_boot0
[ 6.801666] omap_hsi omap_hsi.0: HSI clock is now 96000000
[ 6.824066] omap_hsi omap_hsi.0: Entering RX wakeup in 3 wires mode (no CAWAKE)
[ 6.831634] [MODEM_IF] xmm6260_off()
[ 6.835327] [MODEM_IF] PA EVENT : reset =0, pa=1
[ 6.840057] [MODEM_IF] umts_ipc0 state changed: OFFLINE
[ 6.845367] [MODEM_IF] xmm6260_on()
[ 6.866821] SMC: SecureCRC=0xBC7458DC
[ 6.959045] [MODEM_IF] PA EVENT : reset =1, pa=0
[ 7.042053] SMC PA: INFO 00000001 00:00:00.000 ------ ------ --------------- Booting... (t=00:25:15.356) SMCXG01.04p11.32196 /Widevine Integration
[ 7.058532] SMC PA: INFO 00000002 00:00:00.017 ------ ------ --------------- Booted
[ 7.238128] [MODEM_IF] misc_release : umts_boot0
[ 7.245147] omap_hsi omap_hsi.0: hsi_write_cancel ch 0
[ 7.251708] omap_hsi omap_hsi.0: __hsi_write_cancel : -125
[ 7.258941] omap_hsi omap_hsi.0: hsi_read_cancel ch 0
[ 7.265106] omap_hsi omap_hsi.0: __hsi_read_cancel : -125
[ 7.270629] omap_hsi omap_hsi.0: __hsi_write_cancel : -61
[ 7.276794] omap_hsi omap_hsi.0: __hsi_read_cancel : -61
[ 7.282470] [MODEM_IF] misc_open : umts_boot1
[ 7.287506] omap_hsi omap_hsi.0: Entering RX wakeup in 4 wires mode
[ 8.299774] misc dsscomp: [c7234000] ignoring set failure -22
[ 8.530609] s6e8aa: d/b 1, p 1, b-01390ffb
[ 8.530639] s6e8aa: c0, 1, b-001215fb, got v 3534794, factory wants 3529338
[ 8.530670] s6e8aa: c1, 1, b-00478927, got v 3764175, factory wants 3755229
[ 8.530700] s6e8aa: c2, 1, b-0012a421, got v 3486385, factory wants 3481495
[ 8.530731] s6e8aa: d/b 1, p 2, b-044d7cf9
[ 8.530761] s6e8aa: c0, 2, b-00bc6c9a, got v 3336878, factory wants 3330014
[ 8.530761] s6e8aa: c1, 2, b-01688d4e, got v 3556595, factory wants 3547367
[ 8.530792] s6e8aa: c2, 2, b-00a7db92, got v 3293516, factory wants 3285750
[ 8.530822] s6e8aa: d/b 1, p 3, b-0b323808
[ 8.530853] s6e8aa: c0, 3, b-026395cd, got v 3203365, factory wants 3194725
[ 8.530883] s6e8aa: c1, 3, b-0331a9fb, got v 3435905, factory wants 3424659
[ 8.530914] s6e8aa: c2, 3, b-021e3100, got v 3149091, factory wants 3139262
[ 8.530944] s6e8aa: d/b 1, p 4, b-186611f4
[ 8.530944] s6e8aa: c0, 4, b-062b8517, got v 3065435, factory wants 3053644
[ 8.531036] s6e8aa: c1, 4, b-0725b7f8, got v 3297279, factory wants 3284148
[ 8.531249] s6e8aa: c2, 4, b-053f8b4b, got v 3005194, factory wants 2992315
[ 8.531280] s6e8aa: d/b 1, p 5, b-6840e4ff
[ 8.531311] s6e8aa: c0, 5, b-221c3d41, got v 2688265, factory wants 2667329
[ 8.531341] s6e8aa: c1, 5, b-24fd4a51, got v 2906316, factory wants 2884895
[ 8.531372] s6e8aa: c2, 5, b-1d67176e, got v 2594260, factory wants 2571400
[ 8.531402] s6e8aa: d/b 1, p 6, b-ffffffff
[ 8.531433] s6e8aa: c0, 6, b-59b1b4d2, got v 2325286, factory wants 2292333
[ 8.531463] s6e8aa: c1, 6, b-60d28a3e, got v 2534439, factory wants 2499333
[ 8.531463] s6e8aa: c2, 6, b-4efd2a80, got v 2197307, factory wants 2162000
[ 11.727386] [MODEM_IF] misc_release : umts_boot1
[ 11.732147] omap_hsi omap_hsi.0: hsi_write_cancel ch 0
[ 11.756225] omap_hsi omap_hsi.0: __hsi_write_cancel : -61
[ 11.762268] omap_hsi omap_hsi.0: hsi_read_cancel ch 0
[ 11.767791] omap_hsi omap_hsi.0: __hsi_read_cancel : -125
[ 11.773620] omap_hsi omap_hsi.0: __hsi_write_cancel : -61
[ 11.779174] omap_hsi omap_hsi.0: __hsi_read_cancel : -61
[ 11.785552] [MODEM_IF] misc_open : umts_ipc0
[ 11.790954] omap_hsi omap_hsi.0: Entering RX wakeup in 4 wires mode
[ 11.798675] [MODEM_IF] misc_open : umts_rfs0
[ 11.829528] [MODEM_IF] PA EVENT : reset =1, pa=1
[ 11.834228] [MODEM_IF] umts_ipc0 state changed: ONLINE
[ 14.545074] drivers/misc/inv_mpu/mldl_cfg.c|inv_mpu_get_slave_config|1792 returning 4
[ 26.044372] request_suspend_state: wakeup (3->0) at 26030029299 (2012-05-13 00:25:34.359069826 UTC)
[ 26.622772] acc_open
[ 26.625122] acc_release
[ 26.670013]
[ 26.670043] Dongle Host Driver, version 5.90.125.94
[ 26.670043] Compiled in drivers/net/wireless/bcmdhd on Nov 21 2011 at 19:05:54
[ 26.684082] wl_android_wifi_on in
[ 26.687622] wifi_set_power = 1
[ 26.971282] =========== WLAN going back to live ========
[ 26.977600] sdio_reset_comm():
[ 27.066314] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 27.228179] wifi_get_mac_addr
[ 27.232513] Firmware up: op_mode=1, Broadcom Dongle Host Driver mac=a0:0b:ba:e6:73:ae
[ 27.344390] dhd_rx_frame: net device is NOT registered yet. drop packet
[ 27.351531] dhd_rx_frame: net device is NOT registered yet. drop packet
[ 27.360076] Firmware version = wl0: Oct 5 2011 14:41:12 version 5.90.125.94
[ 28.639709] wl_bss_connect_done succeeded status=(0x9)
[ 28.732391] wl_bss_connect_done succeeded status=(0x11)
[ 29.166564] nfc_power_apply ON
[ 29.201965] nfc_power_apply OFF
[ 29.272308] nfc_power_apply ON
[ 35.672241] rpmsg_omx rpmsg-omx1: local addr assigned: 0x401
[ 35.682067] omap-iommu omap-iommu.0: iommu_get: ducati qos_request
[ 35.703735] omap_hwmod: ipu: failed to hardreset
[ 35.713470] omap-iommu omap-iommu.0: ducati: version 2.1
[ 35.826934] rpmsg_omx rpmsg6: conn rsp: status 0 addr 101
[ 35.975158] rpmsg_omx rpmsg-omx1: Disconnecting from OMX service at 101
[ 39.279998] wlan0: no IPv6 routers present
[ 44.895355] init: untracked pid 1113 exited
[ 44.905731] init: untracked pid 1119 exited
[ 44.918914] init: untracked pid 1123 exited
[ 44.923248] init: untracked pid 1124 exited
[ 44.927612] init: untracked pid 1117 exited
[ 44.932067] init: untracked pid 1120 exited
[ 54.283905] max17040 4-0036: online = 1 vcell = 3788750 soc = 48 status = 3 health = 1 temp = 350 charger status = 0
[ 61.938812] request_suspend_state: sleep (0->3) at 61924468996 (2012-05-13 00:26:10.253540041 UTC)
[ 61.959869] dhd_set_suspend: force extra Suspend setting
first. The device checks if it's too hot or too cold to boot via IROM software (internal read only memory). After that it begins initialization. The IROM version is displayed. Then the device type..
The OMAP processor in the Galaxy Nexus is a HS (High Security) processor, as opposed to GP (General Purpose) processor. This means the first bootloader (AKA MLO or X-Loader) is a signed binary which is e-fused to the device.
I've seen in the past on similar Hummingbird processors that only the first 1K is checked for speed because hashing it takes a little bit of time. This may or may not be the case with this particular device. We will see.
Anyway.. There's a possiblity we can find an MLO which is already presigned somewhere on the Internet. We need whatever they use at Samsung which provides the initial firmware load to a device without any firmware on it.
Here is a relevant page: http://omapedia.org/wiki/Bootloader_Project
Code:
If you are using an HS (High Security) OMAP device, an extra step is required. First, build x-load.bin using the steps above. Then, download the MShield signing tool and use the commands below. Contact your TI representative to get access to this tool.
In order to get the firmware onto the device in the first place, this bootloader must exist. We need a copy of it. Once we have this bootloader, we can revive Galaxy Nexus devices.

You may have seen this already, but just in case - this seems to be a bootloader of some kind. I couldn't get it to work with my bricked SGN, but it may be of some use to the unbricking effort.
Can't post link, so search for "Unbrick dead Samsung GT-i9250 Galaxy Nexus 32GB".
Best of luck!

The user above is referring to this link, I think:
http://forum.xda-developers.com/showthread.php?t=1640443
The user there shares a .zip file that supposedly is able to unbrick a 32gb GNex using some samsung software. It calls OMAPFlash.exe with a bunch of parameters. I don't know whether it will be useful or not, but it's a start.

The batch file that the post above ^ asks the users to run is this:
Code:
::::
:: Copyright (C) 2010-2011, Samsung Electronics, Co., Ltd. All Rights Reserved.
:: Written by System S/W Group, S/W Platform R&D Team,
:: Mobile Communication Division.
::::
::::
:: Project Name : Proxima GED
::
:: Project Description :
::
:: Comments : tabstop = 8, shiftwidth = 8, noexpandtab
::::
::::
:: File Name : omap4460_tuna_hs.bat
::
:: File Description :
::
:: Author : System Platform 2
:: Dept : System S/W Group (S/W Platform R&D Team)
:: Created : 17/Aug/2011
:: Version : Baby-Raccoon
::::
:__loop
@OMAPFlash.exe -v @Targets\Projects\tuna\omap4460_tuna_hs_pro.txt
@PAUSE
GOTO __loop
Seeing the text file path, I went and looked. Here's what I found:
Code:
##
# Copyright (C) 2010-2011, Samsung Electronics, Co., Ltd. All Rights Reserved.
# Written by System S/W Group, S/W Platform R&D Team,
# Mobile Communication Division.
##
##
# Project Name : Proxima GED
#
# Project Description :
#
# Comments : tabstop = 8, shiftwidth = 8, noexpandtab
##
##
# File Name : omap4460_tuna_hs.txt
#
# File Description :
#
# Author : System Platform 2
# Dept : System S/W Group (S/W Platform R&D Team)
# Created : 17/Aug/2011
# Version : Baby-Raccoon
##
-omap 4
-t 36000 -p OMAP4460_TUNA_8G_HS_PRO -2
#chip_download [email protected] Targets\Projects\tuna\MBR.bin
chip_download [email protected] Targets\Projects\tuna\MLO_4460_HS_PRO
chip_download [email protected] Targets\Projects\tuna\sbl.img
command cold_sw_reset
So it appears that the software writes the files MLO_4460_HS_PRO and sbl.img to different parts of the internal memory.

Any success for the device driver? In the documents above, they say you should use the FTDI VCP (Virtual COM Port) drivers... But included in the package above, there is a driver in the ../usb_drv_windows directory, for exactly the TI driver you mentioned:
Code:
%USB_OMAP4460% = USB_Install, USB\VID_0451&PID_d010
For lazy reference:
Code:
[SIZE=2]-- Usage --
OMAPFlash Host is a command-line based application. It is currently available
for Windows XP only and will run in a Windows command shell. The application can
take commands directly from the command line or via a script file (a more useful
approach). The syntax for calling the tool is:
[B]omapflash [ <option> ] <command>[/B]
or, if a script file is used: omapflash @<file>
-- Options --
The tool has a number of options that can be used to control its overall
behavior.
[B]-com <port number> [/B]By default OMAPFlash will try to communicate with the
target platform using a USB serial link. This option will force OMAPFlash to
use a UART for serial communication and specify the host side COM-port to use.
-t <timeout> By default the timeout for communication on the serial link is 5
seconds. This option allows control of the timeout value by specifying another
timeout value in seconds.
[B]-p <platform>[/B] This option is required by OMAPFlash and specifies the platform
for which the download is to take place. The platform specified is a name tag
that allows OMAPFlash to identify the correct second loader to use. The tag
typically identifies the platform type and the memory used with the OMAP
device present on the platform (“e.g. SDP_MDDR_HYNIX_4G). The tag is used to
look up the second loader in a configuration file (omapflash2nd.txt) in
combination with an OMAP device identifier received from the platform during
peripheral boot.
[B]-omap <version> [/B]This option is required by OMAPFlash if a peripheral boot
sequence is used to transfer a second loader to a target platform. The option
specifies the OMAP generation used on the platform – without this option set,
OMAPFlash will be unable to determine how to correctly perform the peripheral
boot sequence necessary for transfer of the second loader to the platform. The
version number is a single digit integer (e.g. ‘3’ for an OMAP3xxx based
platform or ‘4’ for an OMAP4xxx based platform).
[B]-2[/B] This option controls whether OMAPFlash will try to use the ROM code
peripheral boot sequence to transfer a second loader to internal RAM before
doing anything else. This option will be required for most scenarios where
OMAPFlash is used but can be left out if OMAPFlash Host is interacting with a
second loader already running on a target platform.
[B]-v[/B] The ‘-v’ option controls whether OMAPFlash Host will run in verbose mode.
If set, more information will be shown during the execution of the flashing
sequence. Note that this option should be set in order to see the target
platform response to certain commands (e.g. ‘chips’).
-- Commands --
Commands are executed on the target platform. Any command is prefixed by the
keyword ‘command’ and anything following this keyword will be passed directly to
OMAPFlash Second by OMAPFlash Host without interpretation or modification.
Typically the ‘verbose’ option should be used with commands in order to ensure
that information returned from the platform will be shown on the console.
branch <device> <offset>
This command will cause OMAPFlash Second to make an
unconditional branch to a memory mapped address. The device will typically be
the SDRAM handled by the OMAP SDRAM controller in this case, and the offset
typically zero. The device ID must be one known by OMAPFlash Second and the
offset an integer within the address offset range valid for the device.
peek32 <address> Get the register value of the register with the given
address.
poke32 <address> <value> Modify the register at the given address to the given
value
peekpoke32 <address> <value> <mask> Modify the register at the given address
with the given value and mask
-- Flashing --
OMAPFlash Host is able to handle three basic procedures for accessing memory
devices through the OMAPFlash Second loader. These procedures are used to erase
memory devices, transfer a binary file to a device or upload the device content
to a binary file. In all cases, parameter values specifying sizes or offsets are
hexadecimal.
[B]chip_erase <device>[@offset] <size> [/B]
This procedure is used to erase the
content of a device, either for the whole device or for part of its address
range. The ‘device’ identifier is a string matching one of the devices
available on the platform as listed from the ‘chips’ command – in other words,
a device known to OMAPFlash Second for the particular platform used (SDRAM is
not a valid choice). If an ‘offset’ is used, the device erasure will start at
the offset specified. The offset will need to be compatible with the memory
structure of the device in question – e.g. if the device has a block size of
40000h bytes, the offset will need to be a multiple of the block size. The
‘size’ specifies the number of bytes to erase – a value of zero has the
special meaning of “to the end of the device”, either starting at offset zero
or at the specified ‘offset’ value, and can be used to erase the entire
device. Note that the typical erase functionality of a memory device is based
on the erasure of blocks of memory – it may not make sense to ask for erasure
of a size that is not a multiple of the block size of the device.
[B]chip_download <device>[@offset] <file> [/B]
In order to transfer a binary file to a
device on the platform this procedure is used. The ‘device’ identifier is a
string matching one of the devices available on the platform. If an ‘offset’
is specified the binary will be downloaded to the device starting at the
offset address specified. Using an offset should be done with some caution,
since the meaning of the offset value may be unclear for some device types
(e.g. for a NAND device the offset will be used without consideration of bad
blocks present in the memory space preceding the offset address). The file to
be downloaded is specified by the ‘file’ parameter and must be a raw image.
[B]chip_upload <device>[@offset] <size> <file> [/B]
In order to upload the content of
a memory device this procedure is used. The ‘device’ identifier is a string
matching one of the devices available on the platform. If an ‘offset’ is
specified content will be uploaded from the device starting at the offset
address specified. As for the ‘chip_download’ procedure the use of an offset
should be done with caution. The ‘size’ parameter specifies the number of
bytes to upload and the ‘file’ parameter the file to which the uploaded data
will be saved. Note that due to some limitations on the serial link, upload of
data will be considerably slower than download.
[/SIZE]

First things first. I recieved a PM from user itsalllgood with information regarding this topic. Here's the whole PM, copied and pasted:
itsalllgood said:
Dear fred,
Sorry to bother you...I wanted to post here but iam not allowed.. I am a computer engineer from montreal current living abroad..I had gnex that died and did a lot of work to try to get it back..to summ it all the omapidia project add TI site will get the full picture. the tool you linked is based on TI 1.6 omap flash.. i will keep it short... the link below will summ my work and please copy past it if you think its worth it..thanks in advance..
http://forum.xda-developers.com/showthread.php?p=26334564&posted=1#post26334564
Click to expand...
Click to collapse

^^ Somehow your link got messed up, but I think its this one.

Is it possible to hardware prevent a device like Samsung Galaxy S2 to go fastboot / odin mode when powering on but still be able to load the operating system?
Because even although I have a password set on the device, if it is stolen anyone can connect it to fastboot with power+voldown+menu and restore it to defaults. For example filling that corresponding partition with zeros will prevent from entering odin mode unless you boot into the operating system and with dd restore the partition.

First of all, that's off-topic. But I'll provide a speculative answer nonetheless.
I would think that you would be able to prevent a device from reaching recovery/fastboot/odin-download-mode, but it would have a big disadvantage, which is that if you are not able to boot into the OS somehow, you would have an unusable device. Although a device like the Galaxy Nexus, if stolen, could have its data retrieved by potentially using Odin and/or fastboot to reset the password, removing these failsafes would mean that you have a higher chance of bricking. Besides, that's what remote wipe apps (and other stolen-phone tools) are for. Check out Avast! if you don't have an antivirus/stolen-phone toolkit.
I'm by no means an expert here, but that's just my two cents.
EDIT: By the way, could we have someone (like AdamOutler) look at what we've got in this thread so far to see if the MLO file that we found is what's needed (as mentioned by Adam in the first couple posts)?

It's just that I don't either know the exact boot sequence of the SGS2 GT-I9100 nor the partitions interdependence (for example say that the boot partition needs the recovery or the sbl), I coudn't zero that partition because is a dependence.
What I woukd like to know if is possible:
- Backup all partitions.
- Zero, from android with dd, all partitions that allow anyone to enter odin/fastboot/clockworkmod/recovery so, if I lose the device, no one can make a odin backup or reset my device, unless you restore the partitions from the android or you use a hardware JTAG.
- Even the previous done, the phone must be able to normal boot into operating system.

I have a gut feeling that that's not possible. For recovery/odin modes, it may be possible due to them not really being directly involved in the boot process. However, for fastboot, I think it's part of the bootloader itself and therefore cannot be disabled using simple commands without also disabling the phone's booting process. For example, if you have the proper drivers installed on your computer, a Galaxy Nexus that's booting into Android will show up the same device as if you're connected via Fastboot. Unless someone can alter the source and recompile a bootloader with disabled fastboot, I don't think what you stated above is completely possible.

FredFS456 said:
I have a gut feeling that that's not possible. For recovery/odin modes, it may be possible due to them not really being directly involved in the boot process. However, for fastboot, I think it's part of the bootloader itself and therefore cannot be disabled using simple commands without also disabling the phone's booting process. For example, if you have the proper drivers installed on your computer, a Galaxy Nexus that's booting into Android will show up the same device as if you're connected via Fastboot. Unless someone can alter the source and recompile a bootloader with disabled fastboot, I don't think what you stated above is completely possible.
Click to expand...
Click to collapse
I think what I need could be done with a locked bootloader. As far as I know, the Samsung Galaxy S2 comes with an unlocked bootloader (causing the security flaw) while other like Samsung Galaxy Nexus come with a locked one: that means on stock devices, with use pattern or password and usb debugging disabled, there is no way someway can access you data even if not encryption is set.
Anyone can clarify things on this?

Bump, and back on topic.
Any developments here?

Yes. http://forum.xda-developers.com/showthread.php?t=1640443
it's done.

AdamOutler said:
Yes. http://forum.xda-developers.com/showthread.php?t=1640443
it's done.
Click to expand...
Click to collapse
Does anyone know HOW it's done??
EDIT: Actually the accompanying documentation explains quite well!
@Adam: Do you think we could tweak these drivers etc. for other devices not using OMAP?
(It seem that many protocols are standard, inducing the serial (UART) over USB FTDI-drivers...)

E:V:A said:
Does anyone know HOW it's done??
EDIT: Actually the accompanying documentation explains quite well!
@Adam: Do you think we could tweak these drivers etc. for other devices not using OMAP?
(It seem that many protocols are standard, inducing the serial (UART) over USB FTDI-drivers...)
Click to expand...
Click to collapse
It works just like UBM... but stock.
No. I dont think we can do that. Its an omap tool that requires bootmodes to be proper to work on omap. It can be applied to other properly configured omap devices.

[ SOLVED ]HELP NEEDED...Stuck on CM Bootscreen after Nandroid Restore

EDIT : The issue has been resolved.
----------------------------------------------------
Hi guys,sorry for starting a new thread.I've been searching XDA forum and Googling for the solution for 3 days but haven’t found one. I am facing very weird and annoying problem and in desperate need of help.
My Wildfire was working fine on CM 7.2 Stable .Few days back I performed the following things :
1).To resolve the wireless related issues I reflashed Radio (3.35.20.10)
2)Flashed latest Kernel (SympKernV4.5) to give it a try ,was not satisfied and reflashed the previous Kernel (SympKernV4.1)
After that my phone got stuck on the CM boot screen.
I have tried following things :
1)Wiped everything and took nandroid backup without any problem.Everything went well but at the end same boot screen.Yes,I have got two partitions in SDCard FAT32 and ext3.And obviously I used the same version of CWM to restore as I did when creating the backup.
2)Tried the same things 3-4 times to no avail.
3)Ran RUU (RUU_Buzz_HTC_WWE_1.25.405.1_Radio_13.45.55.24_3.35.15.31_release_142189_signed).Downgraded and rooted using unrevoked once again.It was booting fine.Flashed recovery 5.0.2.8.Took nandroid backup everything went perfectly without any Error but when I did the reboot,same CM boot screen.
4.Flashed RemPuzzle_2.81-full and the boot was fine.But again when I tried to restore nandroid backup,got stuck on the same boot screen.I have waited for 5 hours.
5)Tried some other RUUs but the result is still the same.Phone boots perfectly when I flash the RUU. After downgrading and rooting when I try to restore the nandroid backup,it works fine till the end without any error but when I reboot the system it stucks on boot screen.
6) Followed what eventcom has mentioned in http://forum.xda-developers.com/showthread.php?t=1401784&page=2 .Booting was okay but again stuck on boot screen after nandroid restore.
7)Went back to CWM 2.5.0.7 and reflashed the CWM 5.0.2.8.
8.Removed SDCard and SIM before reboot.
9)Don’t think the problem is related to MTD partition as I have formatted all the 3 partitions(/cache,/data and /system).
10)I don’t think the Nandroid Backup has got corrupted coz Nandroid Restore was successful 4 days back before that Radio and Kernel thing moreover I have the backup file saved in PC and I copy the file to SDCard before every new Nandroid restore operation.
Any clues ?
Your help will be much appreciated.Thanks for your time.
Regards

Anybody ?

Hi pal, sorry for my delayed response. Xmas is nuts here :/ ok what I would like you to try is a clean install of cm7 stable and once that's installed go to the play store. The app I want you to get is called nandroid manager, install it and allow it to check your back up. I want to see if it will restore from it or if it will find it corrupt. All going well it will resotre your apps and data and we cam go from there
Sent from my HTC Sensation XE with Beats Audio Z715e using Tapatalk

heavy_metal_man said:
The app I want you to get is called nandroid manager, install it and allow it to check your back up. I want to see if it will restore from it or if it will find it corrupt. All going well it will resotre your apps and data and we cam go from there
Sent from my HTC Sensation XE with Beats Audio Z715e using Tapatalk
Click to expand...
Click to collapse
Hi mate,thanks for your reply.I really appreciate it.There are somethings I need to ask.
1.Right now I am on CWM 2.5.0.1,so before restoring the backup taken by CWM 5.0.2.8 I will have to flash CWM 5.0.2.8 first.Right ?
2.AFAIK,Nandroid Backup is stored in the "backup" folder
Code:
clockworkmod\backup
Right ?
There is another folder "download"
Code:
clockworkmod\download
and two files
Code:
.nomedia
and
Code:
.settings
inside "clockworkmod" folder.
What is the role of "download" folder and those two files ?Do they have anything to do with the nandroid backup ?If I want to restore any nandroid backup,do I also need to move that "download" folder and those two files to "clockworkmod" folder or only moving the backup inside "backup" folder will do the job ?

optimusodd said:
Hi mate,thanks for your reply.I really appreciate it.There are somethings I need to ask.
1.Right now I am on CWM 2.5.0.1,so before restoring the backup taken by CWM 5.0.2.8 I will have to flash CWM 5.0.2.8 first.Right ?
2.AFAIK,Nandroid Backup is stored in the "backup" folder
Code:
clockworkmod\backup
Right ?
There is another folder "download"
Code:
clockworkmod\download
and two files
Code:
.nomedia
and
Code:
.settings
inside "clockworkmod" folder.
What is the role of "download" folder and those two files ?Do they have anything to do with the nandroid backup ?If I want to restore any nandroid backup,do I also need to move that "download" folder and those two files to "clockworkmod" folder or only moving the backup inside "backup" folder will do the job ?
Click to expand...
Click to collapse
If you made the back up with cwm 5 you will need cwm 5 pal. The difference between those two recovery is a scripting change, going from amend to edify I believe. So you need version 5 if that's what the back up was made with
Second your back ups are indeed within the cwm/backup folder. The other folder is for if you use the Rom manager application ( which is made by the same gentleman who makes and maintains cwm recovery) the setting file tells the app your default app settings and preferences and the .nomedia is a dummy file. When android apps like music players and picture viewers ect scan the sdcard for content they also look for the .nomedia file, which tells the app simply that there is no media in the folder and that it does not need to scan it should you want to make one simply create a .txt file and rename it to .nomedia and android apps will ignore the folder when looking for media
So should you want to back up your backups as it were simply copy the whole backup folder from your sd card to your pc, job done
Sent from my HTC Sensation XE with Beats Audio Z715e using Tapatalk

heavy_metal_man said:
The other folder is for if you use the Rom manager application ( which is made by the same gentleman who makes and maintains cwm recovery) the setting file tells the app your default app settings and preferences and the .nomedia is a dummy file. When android apps like music players and picture viewers ect scan the sdcard for content they also look for the .nomedia file, which tells the app simply that there is no media in the folder and that it does not need to scan it should you want to make one simply create a .txt file and rename it to .nomedia and android apps will ignore the folder when looking for media
Click to expand...
Click to collapse
Ah okay,thanks for the explanation.
Okay I used nandroid manager to restore the backup and evrything went well till the end.No error.Nothing.After the completion it rebooted the device and it again got stuck on bootscreen.It has been stuck on bootscreen for last 20 mints.I don't understand why

optimusodd said:
Ah okay,thanks for the explanation.
Okay I used nandroid manager to restore the backup and evrything went well till the end.No error.Nothing.After the completion it rebooted the device and it again got stuck on bootscreen.It has been stuck on bootscreen for last 20 mints.I don't understand why
Click to expand...
Click to collapse
Hmmmm. That's very strange. Do you know how to do a logcat to a text file? If so do one and capture it at boot and we will see if it gives us an error
Sent from my Nexus 7 using Tapatalk 4

heavy_metal_man said:
Hmmmm. That's very strange. Do you know how to do a logcat to a text file? If so do one and capture it at boot and we will see if it gives us an error Sent from my Nexus 7 using Tapatalk 4
Click to expand...
Click to collapse
Okay I had taken a nandroid backup using CWM 5.0.2.8 to be on the safe side before trying to restore the backup via Nandroid manager.So when the restore process via Nandroid manager ended up again as stucked on bootscreen I wiped everything and took the nandroid restore and it was successful.WTH is going on.Seriously,I am clueless
Okay,capture it using adb or CatLog ?

optimusodd said:
Okay I had taken a nandroid backup using CWM 5.0.2.8 to be on the safe side before trying to restore the backup via Nandroid manager.So when the restore process via Nandroid manager ended up again as stucked on bootscreen I wiped everything and took the nandroid restore and it was successful.WTH is going on.Seriously,I am clueless
Click to expand...
Click to collapse
OK so now you have the rom installed with the correct data restored? That's a plus not sure how this has came about though
Sent from my Nexus 7 using Tapatalk 4

heavy_metal_man said:
OK so now you have the rom installed with the correct data restored? That's a plus not sure how this has came about though Sent from my Nexus 7 using Tapatalk 4
Click to expand...
Click to collapse
Nope not the one I want to restore.It's the restoration of the nandroid backup taken of clean CM 7.2 i.e CM7.2+Gapps+Nandroid Manager.
Okay,I do a logcat.
................................EDITED..........................
Hi,I have sent you the logcats.

Here is one of the logcats
HTML:
--------- beginning of /dev/log/main
[ 12-15 19:32:52.341 100:0x64 I/cm ]
Welcome to Android 2.3.7 / CyanogenMod-7.2.0-buzz
[ 12-15 19:32:52.351 101:0x65 I/cm ]
_
[ 12-15 19:32:52.371 102:0x66 I/cm ]
__ __ _ ___ _ _ __ ___ __ _ _ _ _ __ __))
[ 12-15 19:32:52.391 103:0x67 I/cm ]
((_ \(/'((_( ((\( ((_)((_( (('((\( ((`1( ((_)((_(
[ 12-15 19:32:52.401 104:0x68 I/cm ]
)) _))
[ 12-15 19:32:52.421 105:0x69 I/cm ]
[ 12-15 19:32:52.651 119:0x77 I/mountsd ]
Checking filesystems..
[ 12-15 19:32:52.771 95:0x5f I/run-parts ]
e2fsck 1.41.12 (17-May-2010)
[ 12-15 19:32:52.801 95:0x5f I/run-parts ]
/dev/block/mmcblk0p2: clean, 84/65808 files, 53844/262912 blocks
[ 12-15 19:32:52.972 134:0x86 I/mountsd ]
/sd-ext successfully mounted
[ 12-15 19:32:53.602 169:0xa9 D/AK8973 ]
AK8973 daemon 1.3.4 Start
(Library version : 1.2.1.620)
--------- beginning of /dev/log/system
[ 12-15 19:32:53.832 160:0xa0 I/Vold ]
Vold 2.1 (the revenge) firing up
[ 12-15 19:32:53.872 160:0xa0 D/Vold ]
Volume sdcard state changing -1 (Initializing) -> 0 (No-Media)
[ 12-15 19:32:53.993 160:0xb5 D/Vold ]
USB connected
[ 12-15 19:32:54.003 160:0xb5 D/Vold ]
Volume sdcard state changing 0 (No-Media) -> 2 (Pending)
[ 12-15 19:32:54.033 160:0xb5 D/Vold ]
Volume sdcard state changing 2 (Pending) -> 1 (Idle-Unmounted)
[ 12-15 19:32:54.093 161:0xa1 I/Netd ]
Netd 1.0 starting
[ 12-15 19:32:54.213 160:0xb5 D/Vold ]
USB connected
[ 12-15 19:32:54.423 162:0xa2 I/DEBUG ]
debuggerd: Jun 15 2012 12:13:45
[ 12-15 19:32:55.744 164:0xa4 D/AndroidRuntime ]
>>>>>> AndroidRuntime START com.android.internal.os.ZygoteInit <<<<<<
[ 12-15 19:32:55.744 164:0xa4 I/AndroidRuntime ]
Heap size: -Xmx32m
[ 12-15 19:32:55.744 164:0xa4 D/AndroidRuntime ]
CheckJNI is OFF
[ 12-15 19:32:56.285 165:0xa5 I/ ]
ServiceManager: 0xad50
[ 12-15 19:32:56.305 165:0xa5 I/HTC Acoustic ]
libhtc_acoustic.so version 1.0.1.4.
[ 12-15 19:32:56.305 165:0xa5 E/HTC Acoustic ]
Fail to open /system/etc/AudioPara_ALL.csv -1.
[ 12-15 19:32:56.305 165:0xa5 I/HTC Acoustic ]
open /system/etc/AudioPara4.csv success.
[ 12-15 19:32:56.335 165:0xa5 I/HTC Acoustic ]
acoustic table version: Buzz_Generic_20100804
[ 12-15 19:32:56.365 165:0xa5 I/HTC Acoustic ]
read_audio_para_from_file success.
[ 12-15 19:32:56.365 165:0xa5 I/HTC Acoustic ]
get_audpp_filter
[ 12-15 19:32:56.365 165:0xa5 I/HTC Acoustic ]
open /system/etc/AudioFilter.csv success.
[ 12-15 19:32:56.365 165:0xa5 I/HTC Acoustic ]
ADRC Filter ADRC FLAG = ffff.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
ADRC Filter COMP THRESHOLD = 2550.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
ADRC Filter COMP SLOPE = b333.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
ADRC Filter COMP RMS TIME = 106.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
ADRC Filter COMP ATTACK[0] = 7f7d.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
ADRC Filter COMP ATTACK[1] = 3096.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
ADRC Filter COMP RELEASE[0] = 7ff7.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
ADRC Filter COMP RELEASE[1] = 4356.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
ADRC Filter COMP DELAY = 16.
[ 12-15 19:32:56.375 165:0xa5 I/HTC Acoustic ]
EQ flag = ffff.
[ 12-15 19:32:56.395 165:0xa5 I/HTC Acoustic ]
get_audpre_filter
[ 12-15 19:32:56.395 165:0xa5 I/HTC Acoustic ]
open /system/etc/AudioPreProcess.csv success.
[ 12-15 19:32:56.395 165:0xa5 D/AudioHardwareMSM72XX ]
mNumSndEndpoints = 80
[ 12-15 19:32:56.405 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH HANDSET
[ 12-15 19:32:56.405 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH SPEAKER
[ 12-15 19:32:56.405 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH HEADSET
[ 12-15 19:32:56.405 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH BT
[ 12-15 19:32:56.405 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH CARKIT
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH TTY_FULL
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH TTY_VCO
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH TTY_HCO
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH NO_MIC_HEADSET
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH FM_HEADSET
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH HEADSET_AND_SPEAKER
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH FM_SPEAKER
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH BT_EC_OFF
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareMSM72XX ]
BT MATCH CURRENT
[ 12-15 19:32:56.415 165:0xa5 D/AudioHardwareInterface ]
setMode(NORMAL)
[ 12-15 19:32:56.415 165:0xa5 I/AudioHardwareMSM72XX ]
Set master volume to 5.
[ 12-15 19:32:56.435 165:0xa5 I/CameraService ]
CameraService started (pid=165)
[ 12-15 19:32:56.445 165:0xd5 I/AudioFlinger ]
AudioFlinger's thread 0xf2e0 ready to run
[ 12-15 19:32:56.445 165:0xd4 D/AudioFlinger ]
setParameters(): io 1, keyvalue routing=2, tid 212, calling tid 165
[ 12-15 19:32:56.455 165:0xd5 I/AudioHardwareMSM72XX ]
Routing audio to Speakerphone
[ 12-15 19:32:56.455 165:0xd5 D/HTC Acoustic ]
msm72xx_enable_audpp: 0x0007
[ 12-15 19:32:56.465 165:0xd4 D/AudioHardwareMSM72XX ]
setVoiceVolume(1.000000)
[ 12-15 19:32:56.465 165:0xd4 I/AudioHardwareMSM72XX ]
Setting in-call volume to 5 (available range is 0 to 5)
[ 12-15 19:32:57.836 164:0xa4 I/SamplingProfilerIntegration ]
Profiler is disabled.
[ 12-15 19:32:57.906 164:0xa4 I/Zygote ]
Preloading classes...
[ 12-15 19:32:57.916 164:0xa4 E/Zygote ]
setreuid() failed. errno: 2
[ 12-15 19:32:57.926 164:0xa4 D/dalvikvm ]
GC_EXPLICIT freed 48K, 77% free 239K/1024K, external 0K/0K, paused 11ms
[ 12-15 19:32:58.137 164:0xa4 I/bluetooth_ScoSocket.cpp ]
Entry name = MY-CAR ScoTypes = 0x7f
[ 12-15 19:32:58.137 164:0xa4 I/bluetooth_ScoSocket.cpp ]
Entry name = Motorola HF850 ScoTypes = 0x7
[ 12-15 19:33:00.199 164:0xa4 D/szipinf ]
Initializing inflate state
[ 12-15 19:33:04.683 164:0xa4 D/dalvikvm ]
GC_FOR_MALLOC freed 2913K, 57% free 2209K/5123K, external 0K/0K, paused 99ms
[ 12-15 19:33:06.375 164:0xa4 D/dalvikvm ]
GC_FOR_MALLOC freed 2631K, 52% free 2488K/5123K, external 0K/0K, paused 93ms
[ 12-15 19:33:10.529 164:0xa4 I/Zygote ]
...preloaded 1829 classes in 12629ms.
[ 12-15 19:33:10.529 164:0xa4 D/Zygote ]
setreuid() error ignored, same uid.
[ 12-15 19:33:10.619 164:0xa4 D/dalvikvm ]
GC_EXPLICIT freed 891K, 48% free 2685K/5123K, external 0K/0K, paused 82ms
[ 12-15 19:33:10.619 164:0xa4 I/Zygote ]
Preload resources disabled, skipped.
[ 12-15 19:33:10.689 164:0xa4 D/dalvikvm ]
GC_EXPLICIT freed 25K, 49% free 2660K/5123K, external 0K/0K, paused 67ms
[ 12-15 19:33:10.759 164:0xa4 D/dalvikvm ]
GC_EXPLICIT freed <1K, 49% free 2660K/5123K, external 0K/0K, paused 66ms
[ 12-15 19:33:10.819 164:0xa4 D/dalvikvm ]
GC_EXPLICIT freed <1K, 49% free 2660K/5123K, external 0K/0K, paused 66ms
[ 12-15 19:33:10.839 164:0xa4 I/dalvikvm ]
System server process 222 has been created
[ 12-15 19:33:10.839 164:0xa4 I/Zygote ]
Accepting command socket connections
[ 12-15 19:33:11.239 222:0xde I/sysproc ]
Entered system_init()
[ 12-15 19:33:11.239 222:0xde I/sysproc ]
ServiceManager: 0x817f8
[ 12-15 19:33:11.249 222:0xde I/SurfaceFlinger ]
SurfaceFlinger is starting
[ 12-15 19:33:11.249 222:0xde I/SurfaceFlinger ]
dithering enabled
[ 12-15 19:33:11.249 222:0xe6 I/SurfaceFlinger ]
SurfaceFlinger's main thread ready to run. Initializing graphics H/W...
[ 12-15 19:33:11.269 222:0xe6 I/gralloc ]
using (fd=27)
id = msmfb
xres = 240 px
yres = 320 px
xres_virtual = 240 px
yres_virtual = 640 px
bpp = 16
r = 11:5
g = 5:6
b = 0:5
[ 12-15 19:33:11.269 222:0xe6 I/gralloc ]
width = 49 mm (124.408165 dpi)
height = 65 mm (125.046150 dpi)
refresh rate = 60.00 Hz
[ 12-15 19:33:11.279 222:0xe6 D/libEGL ]
egl.cfg not found, using default config
[ 12-15 19:33:11.289 222:0xe6 D/libEGL ]
loaded /system/lib/egl/libGLES_android.so
[ 12-15 19:33:11.309 222:0xe6 I/SurfaceFlinger ]
EGL informations:
[ 12-15 19:33:11.309 222:0xe6 I/SurfaceFlinger ]
# of configs : 8
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
vendor : Android
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
version : 1.4 Android META-EGL
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
extensions: EGL_KHR_image EGL_KHR_image_base EGL_KHR_image_pixmap EGL_KHR_gl_texture_2D_image EGL_KHR_gl_texture_cubemap_image EGL_KHR_gl_renderbuffer_image EGL_ANDROID_image_native_buffer EGL_ANDROID_swap_rectangle EGL_ANDROID_get_render_buffer
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
Client API: OpenGL ES
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
EGLSurface: 5-6-5-0, config=0x0
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
OpenGL informations:
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
vendor : Android
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
renderer : Android PixelFlinger 1.4
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
version : OpenGL ES-CM 1.0
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
extensions: GL_OES_byte_coordinates GL_OES_fixed_point GL_OES_single_precision GL_OES_read_format GL_OES_compressed_paletted_texture GL_OES_draw_texture GL_OES_matrix_get GL_OES_query_matrix GL_OES_EGL_image GL_OES_compressed_ETC1_RGB8_texture GL_ARB_texture_compression GL_ARB_texture_non_power_of_two GL_ANDROID_user_clip_plane GL_ANDROID_vertex_buffer_object GL_ANDROID_generate_mipmap
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
GL_MAX_TEXTURE_SIZE = 4096
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
GL_MAX_VIEWPORT_DIMS = 4096
[ 12-15 19:33:11.319 222:0xe6 I/SurfaceFlinger ]
flags = 000c0000
[ 12-15 19:33:11.330 222:0xde D/SensorService ]
nuSensorService starting...
[ 12-15 19:33:11.340 169:0xa9 D/AK8973 ]
Compass Start
[ 12-15 19:33:11.390 222:0xde I/SensorService ]
BMA150 3-axis Accelerometer
[ 12-15 19:33:11.390 222:0xde I/SensorService ]
AK8973 3-axis Magnetic field sensor
[ 12-15 19:33:11.390 222:0xde I/SensorService ]
AK8973 Orientation sensor
[ 12-15 19:33:11.390 222:0xde I/SensorService ]
CM3602 Proximity sensor
[ 12-15 19:33:11.400 222:0xde I/SensorService ]
CM3602 Light sensor
[ 12-15 19:33:11.400 222:0xde I/sysproc ]
System server: starting Android runtime.
[ 12-15 19:33:11.400 222:0xde I/sysproc ]
System server: starting Android services.
[ 12-15 19:33:11.410 222:0xeb D/SensorService ]
nuSensorService thread starting...
[ 12-15 19:33:11.420 222:0xde I/SystemServer ]
Entered the Android system server!
[ 12-15 19:33:11.440 222:0xde I/sysproc ]
System server: entering thread pool.
[ 12-15 19:33:11.440 222:0xec I/SystemServer ]
Entropy Service
[ 12-15 19:33:11.500 222:0xec I/SystemServer ]
Power Manager
[ 12-15 19:33:11.520 222:0xec I/SystemServer ]
Activity Manager
[ 12-15 19:33:11.610 222:0xed I/ActivityManager ]
Memory class: 32
[ 12-15 19:33:11.750 232:0xef D/libEGL ]
egl.cfg not found, using default config
[ 12-15 19:33:11.760 232:0xef D/libEGL ]
loaded /system/lib/egl/libGLES_android.so
[ 12-15 19:33:11.790 232:0xef W/zipro ]
Unable to open zip '/data/local/bootanimation.zip': No such file or directory
[ 12-15 19:33:12.010 232:0xef I/ARMAssembler ]
generated scanline__00000077:03010104_00008004_00000000 [ 84 ipp] (103 ins) at [0x4076c1e8:0x4076c384] in 3387451 ns
[ 12-15 19:33:12.130 222:0xed I/UsageStats ]
Deleting usage file : usage-20130830
[ 12-15 19:33:12.270 169:0xa9 D/AK8973 ]
Compass CLOSE
[ 12-15 19:33:12.421 222:0xec I/SystemServer ]
Telephony Registry
[ 12-15 19:33:12.461 222:0xec I/SystemServer ]
Package Manager
[ 12-15 19:33:12.501 167:0xa7 I/installd ]
new connection
[ 12-15 19:33:12.501 222:0xec I/Installer ]
connecting...
[ 12-15 19:33:12.771 222:0xe0 D/dalvikvm ]
GC_CONCURRENT freed 156K, 47% free 3020K/5639K, external 0K/0K, paused 7ms+22ms
[ 12-15 19:33:13.602 222:0xe0 D/dalvikvm ]
GC_CONCURRENT freed 314K, 47% free 3239K/6023K, external 0K/0K, paused 22ms+12ms
[ 12-15 19:33:14.733 222:0xe0 D/dalvikvm ]
GC_CONCURRENT freed 537K, 49% free 3260K/6279K, external 0K/0K, paused 7ms+9ms
[ 12-15 19:33:16.014 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:16.124 222:0xe0 D/dalvikvm ]
GC_CONCURRENT freed 272K, 46% free 3423K/6279K, external 0K/0K, paused 8ms+49ms
[ 12-15 19:33:16.715 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:16.785 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:16.875 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:16.965 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:17.746 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:18.136 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:18.336 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:18.446 222:0xe0 D/dalvikvm ]
GC_CONCURRENT freed 164K, 42% free 3694K/6343K, external 0K/0K, paused 7ms+20ms
[ 12-15 19:33:18.466 222:0xec W/PackageParser ]
No actions in intent filter at /system/app/Bluetooth.apk Binary XML file line #132
[ 12-15 19:33:18.466 222:0xec W/PackageParser ]
No actions in intent filter at /system/app/Bluetooth.apk Binary XML file line #154
[ 12-15 19:33:18.667 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:18.847 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:19.167 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:19.387 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:19.507 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:19.888 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:20.138 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:20.388 222:0xec I/PackageManager ]
Package com.android.vending at /system/app/Vending.apk ignored: updated version 80230011 better than this 8007003
[ 12-15 19:33:20.779 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:21.600 222:0xe0 D/dalvikvm ]
GC_CONCURRENT freed 275K, 42% free 3934K/6727K, external 0K/0K, paused 7ms+38ms
[ 12-15 19:33:21.630 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:21.760 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:22.811 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:23.071 222:0xec I/PackageManager ]
Package com.noshufou.android.su at /system/app/Superuser.apk ignored: updated version 46 better than this 38
[ 12-15 19:33:23.081 222:0xec D/PackageManager ]
No files in app dir /vendor/app
[ 12-15 19:33:23.231 222:0xec D/asset ]
failed to open Zip archive '/data/app/com.nuance.swype.trial-1.apk'
[ 12-15 19:33:23.231 222:0xec W/PackageParser ]
Unable to read AndroidManifest.xml of /data/app/com.nuance.swype.trial-1.apk
java.io.FileNotFoundException: AndroidManifest.xml
at android.content.res.AssetManager.openXmlAssetNative(Native Method)
at android.content.res.AssetManager.openXmlBlockAsset(AssetManager.java:521)
at android.content.res.AssetManager.openXmlResourceParser(AssetManager.java:477)
at android.content.pm.PackageParser.parsePackage(PackageParser.java:428)
at com.android.server.PackageManagerService.scanPackageLI(PackageManagerService.java:2715)
at com.android.server.PackageManagerService.scanDirLI(PackageManagerService.java:2640)
at com.android.server.PackageManagerService.<init>(PackageManagerService.java:1029)
at com.android.server.PackageManagerService.main(PackageManagerService.java:725)
at com.android.server.ServerThread.run(SystemServer.java:178)
[ 12-15 19:33:23.321 222:0xec W/PackageManager ]
Package mobi.infolife.uninstaller desires unavailable shared library com.sec.android.app.multiwindow; ignoring!
[ 12-15 19:33:23.531 222:0xec W/ResourceType ]
Failure getting entry for 0x7f09002b (t=8 e=43) in package 0 (error -75)
[ 12-15 19:33:23.992 222:0xe0 D/dalvikvm ]
GC_CONCURRENT freed 300K, 41% free 4064K/6855K, external 0K/0K, paused 20ms+27ms
[ 12-15 19:33:24.042 222:0xec D/asset ]
failed to open Zip archive '/data/app/com.google.android.gms-2.apk'
[ 12-15 19:33:24.062 222:0xec W/PackageParser ]
Unable to read AndroidManifest.xml of /data/app/com.google.android.gms-2.apk
java.io.FileNotFoundException: AndroidManifest.xml
at android.content.res.AssetManager.openXmlAssetNative(Native Method)
at android.content.res.AssetManager.openXmlBlockAsset(AssetManager.java:521)
at android.content.res.AssetManager.openXmlResourceParser(AssetManager.java:477)
at android.content.pm.PackageParser.parsePackage(PackageParser.java:428)
at com.android.server.PackageManagerService.scanPackageLI(PackageManagerService.java:2715)
at com.android.server.PackageManagerService.scanDirLI(PackageManagerService.java:2640)
at com.android.server.PackageManagerService.<init>(PackageManagerService.java:1029)
at com.android.server.PackageManagerService.main(PackageManagerService.java:725)
at com.android.server.ServerThread.run(SystemServer.java:178)
[ 12-15 19:33:24.132 222:0xec D/asset ]
failed to open Zip archive '/data/app/netgenius.bizcal-1.apk'
[ 12-15 19:33:24.132 222:0xec W/PackageParser ]
Unable to read AndroidManifest.xml of /data/app/netgenius.bizcal-1.apk
java.io.FileNotFoundException: AndroidManifest.xml
at android.content.res.AssetManager.openXmlAssetNative(Native Method)
at android.content.res.AssetManager.openXmlBlockAsset(AssetManager.java:521)
at android.content.res.AssetManager.openXmlResourceParser(AssetManager.java:477)
at android.content.pm.PackageParser.parsePackage(PackageParser.java:428)
at com.android.server.PackageManagerService.scanPackageLI(PackageManagerService.java:2715)
at com.android.server.PackageManagerService.scanDirLI(PackageManagerService.java:2640)
at com.android.server.PackageManagerService.<init>(PackageManagerService.java:1029)
at com.android.server.PackageManagerService.main(PackageManagerService.java:725)
at com.android.server.ServerThread.run(SystemServer.java:178)
[ 12-15 19:33:24.352 222:0xec W/ResourceType ]
Failure getting entry for 0x7f050000 (t=4 e=0) in package 0 (error -75)
[ 12-15 19:33:24.392 222:0xec D/asset ]
failed to open Zip archive '/data/app/com.googlecode.droidwall.free-1.apk'
[ 12-15 19:33:24.402 222:0xec W/PackageParser ]
Unable to read AndroidManifest.xml of /data/app/com.googlecode.droidwall.free-1.apk
java.io.FileNotFoundException: AndroidManifest.xml
at android.content.res.AssetManager.openXmlAssetNative(Native Method)
at android.content.res.AssetManager.openXmlBlockAsset(AssetManager.java:521)
at android.content.res.AssetManager.openXmlResourceParser(AssetManager.java:477)
at android.content.pm.PackageParser.parsePackage(PackageParser.java:428)
at com.android.server.PackageManagerService.scanPackageLI(PackageManagerService.java:2715)
at com.android.server.PackageManagerService.scanDirLI(PackageManagerService.java:2640)
at com.android.server.PackageManagerService.<init>(PackageManagerService.java:1029)
at com.android.server.PackageManagerService.main(PackageManagerService.java:725)
at com.android.server.ServerThread.run(SystemServer.java:178)
[ 12-15 19:33:24.412 222:0xec D/szipinf ]
Initializing inflate state
[ 12-15 19:33:24.522 222:0xec D/asset ]
failed to open Zip archive '/data/app/com.ruimaninfo.approtect-1.apk'
[ 12-15 19:33:24.532 222:0xec W/PackageParser ]
Unable to read AndroidManifest.xml of /data/app/com.ruimaninfo.approtect-1.apk
java.io.FileNotFoundException: AndroidManifest.xml
at android.content.res.AssetManager.openXmlAssetNative(Native Method)
at android.content.res.AssetManager.openXmlBlockAsset(AssetManager.java:521)
at android.content.res.AssetManager.openXmlResourceParser(AssetManager.java:477)
at android.content.pm.PackageParser.parsePackage(PackageParser.java:428)
at com.android.server.PackageManagerService.scanPackageLI(PackageManagerService.java:2715)
at com.android.server.PackageManagerService.scanDirLI(PackageManagerService.java:2640)
at com.android.server.PackageManagerService.<init>(PackageManagerService.java:1029)
at com.android.server.PackageManagerService.main(PackageManagerService.java:725)
at com.android.server.ServerThread.run(SystemServer.java:178)
[ 12-15 19:33:24.783 222:0xec D/asset ]
failed to open Zip archive '/data/app/org.adaway-2.apk'
[ 12-15 19:33:24.793 222:0xec W/PackageParser ]
Unable to read AndroidManifest.xml of /data/app/org.adaway-2.apk
java.io.FileNotFoundException: AndroidManifest.xml
at android.content.res.AssetManager.openXmlAssetNative(Native Method)
at android.content.res.AssetManager.openXmlBlockAsset(AssetManager.java:521)
at android.content.res.AssetManager.openXmlResourceParser(AssetManager.java:477)
at android.content.pm.PackageParser.parsePackage(PackageParser.java:428)
at com.android.server.PackageManagerService.scanPackageLI(PackageManagerService.java:2715)
at com.android.server.PackageManagerService.scanDirLI(PackageManagerService.java:2640)
at com.android.server.PackageManagerService.<init>(PackageManagerService.java:1029)
at com.android.server.PackageManagerService.main(PackageManagerService.java:725)
at com.android.server.ServerThread.run(SystemServer.java:178)
[ 12-15 19:33:25.003 222:0xec D/asset ]
failed to open Zip archive '/data/app/com.modoohut.dialer.theme.dark-1.apk'
[ 12-15 19:33:25.013 222:0xec W/PackageParser ]
Unable to read AndroidManifest.xml of /data/app/com.modoohut.dialer.theme.dark-1.apk
java.io.FileNotFoundException: AndroidManifest.xml
at android.content.res.AssetManager.openXmlAssetNative(Native Method)
at android.content.res.AssetManager.openXmlBlockAsset(AssetManager.java:521)
at android.content.res.AssetManager.openXmlResourceParser(AssetManager.java:477)
at android.content.pm.PackageParser.parsePackage(PackageParser.java:428)
at com.android.server.PackageManagerService.scanPackageLI(PackageManagerService.java:2715)
at com.android.server.PackageManagerService.scanDirLI(PackageManagerService.java:2640)
at com.android.server.PackageManagerService.<init>(PackageManagerService.java:1029)
at com.android.server.PackageManagerService.main(PackageManagerService.java:725)
at com.android.server.ServerThread.run(SystemServer.java:178)
[ 12-15 19:33:25.013 222:0xec D/asset ]
failed to open Zip archive '/data/app/com.buak.Link2SD-2.apk'
[ 12-15 19:33:25.023 222:0xec W/PackageParser ]
Unable to read AndroidManifest.xml of /data/app/com.buak.Link2SD-2.apk
java.io.FileNotFoundException: AndroidManifest.xml
at android.content.res.AssetManager.openXmlAssetNative(Native Method)
at android.content.res.AssetManager.openXmlBlockAsset(AssetManager.java:521)
at android.content.res.AssetManager.openXmlResourceParser(AssetManager.java:477)
at android.content.pm.PackageParser.parsePackage(PackageParser.java:428)
at com.android.server.PackageManagerService.scanPackageLI(PackageManagerService.java:2715)
at com.android.server.PackageManagerService.scanDirLI(PackageManagerService.java:2640)
at com.android.server.PackageManagerService.<init>(PackageManagerService.java:1029)
at com.android.server.PackageManagerService.main(PackageManagerService.java:725)
at com.android.server.ServerThread.run(SystemServer.java:178)

Is there any chance someone can explain what's going wrong and help me to get it running again ?
I will really appreciate that.
dmseg log
Code:
<6>[ 0.000000] Initializing cgroup subsys cpu
<5>[ 0.000000] Linux version 2.6.35.14-SympFinity+ ([email protected]) (gcc version 4.4.3 (GCC) ) #40 PREEMPT Wed May 2 14:11:03 CEST 2012
<4>[ 0.000000] CPU: ARMv6-compatible processor [4117b362] revision 2 (ARMv6TEJ), cr=00c5387f
<4>[ 0.000000] CPU: VIPT aliasing data cache, VIPT aliasing instruction cache
<4>[ 0.000000] Machine: buzz
<7>[ 0.000000] find the smi tag
<7>[ 0.000000] parse_tag_smi: smi size = 0
<7>[ 0.000000] find the hwid tag
<7>[ 0.000000] parse_tag_hwid: hwid = 0x1
<7>[ 0.000000] find the skuid tag
<7>[ 0.000000] parse_tag_skuid: hwid = 0x2490b
<7>[ 0.000000] tag_panel_parsing: panel type = 0
<7>[ 0.000000] find the engineer tag
<7>[ 0.000000] parse_tag_engineerid: 0x0
<4>[ 0.000000] Ignoring unrecognised tag 0x4d534d76
<4>[ 0.000000] Ignoring unrecognised tag 0x5441000a
<6>[ 0.000000] CAM_AWB_CAL Data size = 514 , 0x59504550, size = 2048
<4>[ 0.000000] Ignoring unrecognised tag 0x41387898
<4>[ 0.000000] BT Data size= 4, 0x43294329,d4,20,6d,94,70,72,00,00,Memory policy: ECC disabled, Data cache writeback
<7>[ 0.000000] On node 0 totalpages: 82432
<7>[ 0.000000] free_area_init_node: node 0, pgdat c052ed50, node_mem_map c06d2000
<7>[ 0.000000] Normal zone: 1156 pages used for memmap
<7>[ 0.000000] Normal zone: 0 pages reserved
<7>[ 0.000000] Normal zone: 81276 pages, LIFO batch:15
<4>[ 0.000000] buzz_init_map_io()
<4>[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 81276
<5>[ 0.000000] Kernel command line: board_buzz.disable_uart3=0 board_buzz.usb_h2w_sw=0 board_buzz.disable_sdcard=0 diag.enabled=0 board_buzz.debug_uart=0 smisize=0 userdata_sel=0 androidboot.emmc=false androidboot.baseband=3.35.20.10 androidboot.cid=11111111 androidboot.batt_poweron=good_battery androidboot.carrier=ALL androidboot.mid=PC4910000 androidboot.keycaps=qwerty androidboot.mode=normal androidboot.serialno=MB139PY05248 androidboot.bootloader=6.01.1002 zygote_oneshot=off no_console_suspend=1 console=null mtdparts=msm_nand:[email protected](misc),[email protected](recovery),[email protected](boot),[email protected]40000(system),[email protected](cache),[email protected](userdata)
<6>[ 0.000000] board_bootloader_setup: 6.01.1002
<6>[ 0.000000] board_bootloader_setup: default ENG BUILD
<6>[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
<6>[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>[ 0.000000] Memory: 210MB 112MB = 322MB total
<5>[ 0.000000] Memory: 319632k/319632k available, 10096k reserved, 0K highmem
<5>[ 0.000000] Virtual kernel memory layout:
<5>[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
<5>[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
<5>[ 0.000000] DMA : 0xffa00000 - 0xffe00000 ( 4 MB)
<5>[ 0.000000] vmalloc : 0xe4800000 - 0xf8000000 ( 312 MB)
<5>[ 0.000000] lowmem : 0xc0000000 - 0xe4200000 ( 578 MB)
<5>[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
<5>[ 0.000000] .init : 0xc0008000 - 0xc002c000 ( 144 kB)
<5>[ 0.000000] .text : 0xc002c000 - 0xc04f6000 (4904 kB)
<5>[ 0.000000] .data : 0xc04f6000 - 0xc052f360 ( 229 kB)
<6>[ 0.000000] NR_IRQS:277
<4>[ 0.000000] buzz_init_irq()
<6>[ 0.000000] Calibrating delay loop... 480.05 BogoMIPS (lpj=2400256)
<6>[ 0.250122] pid_max: default: 32768 minimum: 301
<4>[ 0.250579] Mount-cache hash table entries: 512
<6>[ 0.251434] Initializing cgroup subsys cpuacct
<6>[ 0.251525] Initializing cgroup subsys freezer
<6>[ 0.251525] Initializing cgroup subsys net_cls
<6>[ 0.251556] Initializing cgroup subsys bfqio
<6>[ 0.251586] Initializing cgroup subsys timer_slack
<6>[ 0.251647] CPU: Testing write buffer coherency: ok
<6>[ 0.256469] NET: Registered protocol family 16
<4>[ 0.257446] buzz_init() revision = 0x81
<6>[ 0.257507] BT HW address=d4:20:6d:94:70:72
<6>[ 1.876647] acpu_clock_init()
<6>[ 1.877136] ACPU running at 480000 KHz
<6>[ 1.878387] ram_console: got buffer at 2d9b000, size 20000
<6>[ 1.878936] ram_console: uncorrectable error in header
<6>[ 1.879028] ram_console: no valid data in buffer (sig = 0xffffffff)
<6>[ 1.905426] console [ram-1] enabled
<6>[ 1.905761] buzz_init_mmc
<6>[ 1.908264] buzz_wifi_init: start
<4>[ 1.919372] bio: create slab <bio-0> at 0
<6>[ 1.922119] [DISP]mdp_probe: initialized
<6>[ 1.922943] msm_i2c_probe
<6>[ 1.923492] msm_i2c_probe: clk_ctl 315, 400000 Hz
<6>[ 1.927551] Bluetooth: Core ver 2.16
<6>[ 1.928070] NET: Registered protocol family 31
<6>[ 1.928375] Bluetooth: HCI device and connection manager initialized
<6>[ 1.928924] Bluetooth: HCI socket layer initialized
<6>[ 1.929229] Bluetooth: L2CAP socket layer initialized
<6>[ 1.930267] Bluetooth: SCO socket layer initialized
<6>[ 1.931182] Switching to clocksource gp_timer
<6>[ 1.934631] NET: Registered protocol family 2
<6>[ 1.935455] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
<6>[ 1.937103] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<6>[ 1.938598] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
<6>[ 1.939666] TCP: Hash tables configured (established 16384 bind 16384)
<6>[ 1.940216] TCP reno registered
<6>[ 1.940521] UDP hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 1.940856] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
<6>[ 1.942077] NET: Registered protocol family 1
<6>[ 1.943023] Unpacking initramfs...
<6>[ 1.975341] Freeing initrd memory: 144K
<6>[ 1.976989] [SMD]smd_init()
<6>[ 1.977294] [SMD]smd_core_init()
<6>[ 1.977600] [SMD]phy addr of smd_info.state=0x8023A0
<6>[ 1.978302] [SMD]smd_core_init() done
<3>[ 1.978607] msm_init_last_radio_log: could not retrieve SMEM_CLKREGIM_BSP
<3>[ 1.979278] _smem_log_init: no power log or log_idx allocated, smem_log disabled
<6>[ 1.980804] [SMD]smd_alloc_channel() cid=01 size=08192 'SMD_DIAG'
<6>[ 1.981658] [SMD]smd_alloc_channel() cid=02 size=08192 'SMD_RPCCALL'
<6>[ 1.984985] [SMD]SMD: ch 2 0 -> 1
<6>[ 1.985382] [SMD]smd_alloc_channel() cid=11 size=65536 'SMD_DATA5'
<6>[ 1.985687] [SMD]SMD: ch 2 1 -> 2
<6>[ 1.986602] [SMD]smd_alloc_channel() cid=12 size=08192 'SMD_DATA6'
<6>[ 1.987152] [SMD]smd_alloc_channel() cid=13 size=08192 'SMD_DATA7'
<6>[ 1.987884] [SMD]smd_alloc_channel() cid=38 size=08192 'SMD_DATA5_CNTL'
<6>[ 1.988342] [SMD]smd_alloc_channel() cid=39 size=08192 'SMD_DATA6_CNTL'
<6>[ 1.989044] [SMD]smd_alloc_channel() cid=40 size=08192 'SMD_DATA7_CNTL'
<6>[ 1.996368] Acquire 'boot-time' no_halt_lock 60s
<6>[ 1.997589] [HS_MGR] (headset_notifier_register) Register MIC_BIAS notifier
<6>[ 1.998138] [HS_MGR] (headset_notifier_update) HS_MGR driver is not ready
<7>[ 2.018249] Registered led device: flashlight
<6>[ 2.018585] [FLT]flashlight_probe: led_count = 0
<6>[ 2.019104] [FLT]flashlight_probe: The Flashlight Driver is ready
<6>[ 2.029968] atmega-microp 0-0066: microp version [06][22]
<3>[ 2.034484] microp_function_check: No function 2 !!
<6>[ 2.038024] [HS_MGR] (htc_headset_mgr_probe) ++++++++++++++++++++
<6>[ 2.040222] input: h2w headset as /devices/virtual/input/input0
<6>[ 2.041198] [HS_MGR] (hs_notify_driver_ready) HS_MGR ready
<6>[ 2.042266] [HS_MGR] (htc_headset_mgr_probe) --------------------
<6>[ 2.043060] [HS_MICROP] (htc_headset_microp_probe) ++++++++++++++++++++
<6>[ 2.047729] [HS_MGR] (headset_notifier_register) Register REMOTE_ADC notifier
<6>[ 2.048309] [HS_MGR] (headset_notifier_register) Register MIC_STATUS notifier
<6>[ 2.048614] [HS_MGR] (headset_notifier_register) Register KEY_INT_ENABLE notifier
<6>[ 2.049133] [HS_MGR] (hs_notify_driver_ready) HS_MICROP ready
<6>[ 2.049865] [HS_GPIO] (htc_headset_gpio_probe) ++++++++++++++++++++
<6>[ 2.051300] [HS_MGR] (headset_notifier_register) Register HPIN_GPIO notifier
<6>[ 2.052032] [HS_MGR] (hs_notify_driver_ready) HS_GPIO ready
<6>[ 2.052368] [HS_GPIO] (htc_headset_gpio_probe) --------------------
<6>[ 2.052917] [HS_MICROP] (htc_headset_microp_probe) --------------------
<6>[ 2.080139] [BATT] M2A_RPC: cable_update: USB at 458867027 (1970-01-01 00:00:00.458257102 UTC)
<6>[ 2.081024] [BATT] htc_cable_status_update: 0 -> 1
<6>[ 2.081329] [USB] msm_hsusb_set_vbus_state: 1
<6>[ 2.083099] ashmem: initialized
<6>[ 2.084472] [BATT] A2M_RPC: get_batt_info: batt_id=1, batt_vol=3893, batt_temp=309, batt_current=1017, level=72, charging_source=1, charging_enabled=1, full_bat=1300000, over_vchg=0 at 463716046 (1970-01-01 00:00:00.462557151 UTC)
<5>[ 2.087890] Slow work thread pool: Starting up
<5>[ 2.101501] Slow work thread pool: Ready
<6>[ 2.102264] fuse init (API version 7.14)
<6>[ 2.104644] aufs 2.1-standalone.tree-35-20110418
<4>[ 2.104980] yaffs May 2 2012 14:03:42 Installing.
<6>[ 2.116912] io scheduler noop registered
<6>[ 2.117492] io scheduler bfq registered
<6>[ 2.118041] io scheduler sio registered (default)
<6>[ 2.118316] io scheduler vr registered
<6>[ 2.119354] [DISP]mddi: init() base=0xe4814000 irq=16
<7>[ 2.120178] [DISP]mddi runs at 81920000
<6>[ 2.122161] [DISP]mddi cmd send rtd: int 3a000, stat 8063, rtd val 10
<6>[ 2.125061] [DISP]mddi: registering panel mddi_c_0101_04d1
<6>[ 2.125366] [DISP]mddi: publish:
<7>[ 2.128784] [DISP]mddi_s6d04d1_probe: enter.
<6>[ 2.129547] [DISP]vsync on gpio 97 now 0
<6>[ 2.129852] [DISP]CABC enabled
<7>[ 2.131408] Registered led device: lcd-backlight
<6>[ 2.133544] [DISP]msmfb_probe() installing 240 x 320 panel
<6>[ 2.137268] PRUE G
<6>[ 2.137908] msm_serial_hs.0: ttyHS0 at MMIO 0xa0200000 (irq = 45) is a MSM HS UART
<6>[ 2.139251] msm_serial_hs module loaded
<6>[ 2.139923] [BT]msm_serial_hs module loaded
<6>[ 2.141357] [BT]msm_serial_hs module loaded
<6>[ 2.142852] [BT]msm_serial_hs module loaded
<6>[ 2.149993] loop: module loaded
<6>[ 2.150695] pmem: 1 init
<6>[ 2.151824] pmem_adsp: 0 init
<6>[ 2.153259] pmem_camera: 0 init
<6>[ 2.155090] spi_bma150_probe: G-sensor connect with microP: start initial, kvalue = 0x0
<6>[ 2.165435] [GSNR] Gsensor disable
<6>[ 2.167724] msm_nand: allocated dma buffer at ffa47000, dma_addr 26ecc000
<6>[ 2.168334] status: c03120
<6>[ 2.168640] nandid: 5500bcec maker ec device bc
<6>[ 2.169158] Found a supported NAND device
<6>[ 2.169433] NAND Id : 0xBCEC
<6>[ 2.169738] Buswidth : 16 Bits
<6>[ 2.170257] Density : 512 MByte
<6>[ 2.170532] Pagesize : 2048 Bytes
<6>[ 2.170806] Erasesize: 131072 Bytes
<6>[ 2.171295] Oobsize : 64 Bytes
<6>[ 2.171691] msm_nand: read CFG0 = aa5400c0, CFG1 = 8746a
<6>[ 2.172149] CFG0 Init : 0xe85408c0
<6>[ 2.172668] CFG1 Init : 0x0008746a
<6>[ 2.172943] CFG0: cw/page=3 ud_sz=516 ecc_sz=10 spare_sz=0 num_addr_cycles=5
<6>[ 2.173553] DEV_CMD1: f00f3000
<6>[ 2.173889] <6>NAND_EBI2_ECC_BUF_CFG: 1ff
<5>[ 2.174255] 6 cmdlinepart partitions found on MTD device msm_nand
<5>[ 2.174774] Creating 6 MTD partitions on "msm_nand":
<5>[ 2.175140] 0x00001ff60000-0x000020000000 : "misc"
<5>[ 2.178192] 0x000002760000-0x000002b80000 : "recovery"
<5>[ 2.184356] 0x000002b80000-0x000002e40000 : "boot"
<5>[ 2.189056] 0x000002e40000-0x000009c40000 : "system"
<6>[ 2.214324] [SMD]smd_alloc_channel() cid=27 size=08192 'SMD_GPSNMEA'
<5>[ 2.324920] 0x000009c40000-0x00000ab40000 : "cache"
<6>[ 2.337524] [SMD]smd_alloc_channel() cid=00 size=08192 'SMD_DS'
<6>[ 2.338500] [SMD]smd_alloc_channel() cid=07 size=08192 'SMD_DATA1'
<6>[ 2.339569] [SMD]smd_alloc_channel() cid=08 size=08192 'SMD_DATA2'
<6>[ 2.340545] [SMD]smd_alloc_channel() cid=09 size=08192 'SMD_DATA3'
<6>[ 2.341217] [SMD]smd_alloc_channel() cid=10 size=08192 'SMD_DATA4'
<6>[ 2.342712] [SMD]smd_alloc_channel() cid=15 size=65536 'SMD_DATA9'
<5>[ 2.348907] 0x00000ab40000-0x00001ff60000 : "userdata"
<6>[ 2.694793] PPP generic driver version 2.4.2
<6>[ 2.695587] PPP Deflate Compression module registered
<6>[ 2.695892] PPP BSD Compression module registered
<6>[ 2.699340] PPP MPPE Compression module registered
<6>[ 2.699676] NET: Registered protocol family 24
<6>[ 2.701385] tun: Universal TUN/TAP device driver, 1.6
<6>[ 2.701690] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
<6>[ 2.706115] [USB] msm72k_probe
<6>[ 2.706451] [USB] accessory detect 1
<6>[ 2.706726] [USB] id_pin_gpio 19
<6>[ 2.707000] [USB] dock detect 0
<6>[ 2.707275] [USB] dock pin gpio 0
<6>[ 2.707763] [USB] msm72k_probe() io=e481c000, irq=47, dma=ffa48000(26ef6000)
<6>[ 2.710296] android init
<6>[ 2.710784] android_probe pdata: c0509938
<6>[ 2.711273] android_bind
<7>[ 2.711578] android_bind_config
<6>[ 2.712707] android_usb gadget: android_usb ready
<6>[ 2.713012] [USB] msm72k_udc: registered gadget driver 'android_usb'
<6>[ 2.713775] f_adb init
<6>[ 2.714050] android_register_function adb
<6>[ 2.714355] f_mass_storage init
<6>[ 2.714996] fsg_probe pdev: c0509a98, pdata: c050a484
<6>[ 2.715454] android_register_function usb_mass_storage
<6>[ 2.715728] f_rndis init
<6>[ 2.716491] android_register_function rndis
<6>[ 2.716766] f_accessory init
<6>[ 2.717041] android_register_function accessory
<6>[ 2.717559] diag init
<6>[ 2.717864] android_register_function diag
<6>[ 2.718170] rndis_function_bind_config MAC: 00:00:00:00:00:00
<4>[ 2.718841] android_usb gadget: using random self ethernet address
<4>[ 2.719177] android_usb gadget: using random host ethernet address
<6>[ 2.721954] acc_bind_config
<6>[ 2.723724] [USB] hsusb: IDLE -> ONLINE
<6>[ 2.724060] [USB] lpm exit
<6>[ 2.724639] [USB] hsusb: reset controller
<6>[ 2.725219] android_usb gadget: Mass Storage Function, version: 2009/09/11
<6>[ 2.725524] android_usb gadget: Number of LUNs=1
<6>[ 2.726074] lun0: LUN: removable file: (no medium)
<6>[ 2.726623] adb_bind_config
<6>[ 2.727661] diag_bind_config
<6>[ 2.728210] [SMD]SMD: ch 1 0 -> 1
<6>[ 2.728546] [SMD]SMD: ch 1 1 -> 2
<6>[ 2.729675] buzz_syn_ts_power: power 1
<6>[ 2.762145] msm_hsusb_phy_reset
<6>[ 2.912231] [USB] ulpi: write 0x2c to 0x31
<6>[ 2.912536] [USB] ulpi: write 0x20 to 0x32
<6>[ 2.913024] [USB] ulpi: write 0x01 to 0x0d
<6>[ 2.913299] [USB] ulpi: write 0x01 to 0x10
<6>[ 2.913604] [USB] handle_notify_offline: notify offline
<6>[ 2.914154] [USB] msm_hsusb: enable pullup
<6>[ 2.917449] [USB] suspend
<6>[ 2.932250] [USB] not AC charger
<6>[ 2.932800] [USB] accessory_detect_init: id pin 19
<6>[ 2.993591] synaptics_ts_probe: panel_version: 301
<6>[ 2.995056] max_x: 3DE, max_y: 5A6
<6>[ 2.996887] synaptics_ts_probe: max_x 990, max_y 1446
<6>[ 2.997161] input_set_abs_params: mix_x 0, max_x 990, min_y 0, max_y 1300
<6>[ 2.998229] input: synaptics-rmi-touchscreen as /devices/virtual/input/input1
<6>[ 2.999450] synaptics_ts_probe: Start touchscreen synaptics-rmi-touchscreen in interrupt mode
<6>[ 3.000122] atmel_ts_init():
<6>[ 3.000915] buzz_ts_atmel_power():
<6>[ 3.023895] [USB] reset
<6>[ 3.024291] [USB] send connect type 1
<6>[ 3.024566] [BATT] online=1
<6>[ 3.024841] [BATT] Update SMEM: cable type 1 at 1403189275 (1970-01-01 00:00:01.402670622 UTC)
<6>[ 3.026184] [USB] portchange USB_SPEED_HIGH
<6>[ 3.184234] [USB] reset
<6>[ 3.186492] [USB] portchange USB_SPEED_HIGH
<6>[ 3.282318] No Messages after reset
<3>[ 3.282989] msm_i2c msm_i2c.0: error, status c8 (4A,00,01)(20,13,01)(cnt:7,pos:0)
<3>[ 3.283325] msm_i2c msm_i2c.0: Error during data xfer (-5) (4A,00,01)
<6>[ 3.283874] No Atmel chip inside
<4>[ 3.284362] atmel_qt602240: probe of 0-004a failed with error -5
<6>[ 3.285217] [PS][CM3602] capella_cm3602_probe: probe
<6>[ 3.286346] input: proximity as /devices/virtual/input/input2
<6>[ 3.287506] [PS][CM3602] capella_cm3602_setup
<6>[ 3.288635] [KEY] GPIO Matrix Keypad Driver: Start keypad matrix for buzz-keypad... in interrupt mode
<6>[ 3.289764] [KEY] GPIO_Input_ISR : 0, return IRQ_HANDLED;
<6>[ 3.290252] [KEY] GPIO Input Driver: Start gpio inputs for buzz-keypad... in interrupt mode
<6>[ 3.291442] input: buzz-keypad as /devices/virtual/input/input3
<6>[ 3.292602] input: buzz-nav as /devices/virtual/input/input4
<6>[ 3.294708] input: lightsensor-level as /devices/virtual/input/input5
<6>[ 3.295867] [KEY] gpio_keys_scan_keys: key 1-116, 0 (20) changed to 0
<6>[ 3.296295] [LS][CM3602] set_ls_kvalue: ALS calibrated als_kadc=0x6da5007b
<6>[ 3.296813] [LS][CM3602] set_ls_kvalue: als_kadc=0x7b, als_gadc=0xcf
<6>[ 3.297088] [LS][CM3602] ls_table: data[0] , data[0] = 0, 0
<6>[ 3.297607] [LS][CM3602] ls_table: data[1] , data[1] = 0, 1
<6>[ 3.297882] [LS][CM3602] ls_table: data[2] , data[2] = 0, 2
<6>[ 3.298370] [LS][CM3602] ls_table: data[3] , data[3] = 0, 8
<6>[ 3.298645] [LS][CM3602] ls_table: data[4] , data[4] = 0, 16
<6>[ 3.299163] [LS][CM3602] ls_table: data[5] , data[5] = 0, 59
<6>[ 3.299438] [LS][CM3602] ls_table: data[6] , data[6] = 0, a2
<6>[ 3.299957] [LS][CM3602] ls_table: data[7] , data[7] = 0, b1
<6>[ 3.300231] [LS][CM3602] ls_table: data[8] , data[8] = 0, bf
<6>[ 3.300720] [LS][CM3602] ls_table: data[9] , data[9] = 3, ff
<7>[ 3.303375] __capella_cm3602_power: Turn the capella_cm3602 power on
<6>[ 3.305236] input: curcial-oj as /devices/virtual/input/input6
<3>[ 3.307250] curcial_oj_poweron:eek:J:power status ok
<6>[ 3.356567] OpticalJoystick Device ID: 0d
<6>[ 3.359466] OJ Driver: Revision : 02
<6>[ 3.362548] OJ: driver loaded
<6>[ 3.365692] using rtc device, msm_rtc, for alarms
<6>[ 3.366058] rs30000048:915823fc rs30000048:915823fc: rtc core: registered msm_rtc as rtc0
<6>[ 3.367004] AKM8973 compass driver: init
<6>[ 3.368713] input: compass as /devices/virtual/input/input7
<6>[ 3.370635] [FLT]adp1650 Led Flash driver: init
<4>[ 3.371124] [CAM]s5k4e1gx_init
<4>[ 3.371643] [CAM]__s5k4e1gx_probe
<6>[ 3.372161] [CAM]s5k4e1gx_vreg_enable camera vreg on
<6>[ 3.372772] [CAM]sctrl.node 0
<4>[ 3.373046] [CAM]s5k4e1gx_sensor_probe()
<6>[ 3.373657] [CAM]s5k4e1gx_probe called!
<6>[ 3.424224] [CAM]s5k4e1gx_probe successed! rc = 0
<6>[ 3.424652] [CAM]s5k4e1gx s->node 0
<6>[ 3.437164] android_usb gadget: high speed config #1: android
<6>[ 3.471588] [CAM]s5k4e1gx_sensor_init(): reseting sensor.
<6>[ 3.472961] [CAM]sensor_lc_disable=0
<4>[ 3.568450] [CAM]sensor evt version : 0x10
<4>[ 3.568725] [CAM]use analog_settings_evt3
<6>[ 3.580780] s5k4e1gx_sysfs_init : kobject_create_and_add
<6>[ 3.581146] s5k4e1gx_sysfs_init : sysfs_create_file
<6>[ 3.583343] device-mapper: uevent: version 1.0.3
<6>[ 3.584838] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: [email protected]
<6>[ 3.585510] Bluetooth: HCI UART driver ver 2.2
<6>[ 3.585784] Bluetooth: HCI H4 protocol initialized
<6>[ 3.587799] cpuidle: using governor ladder
<6>[ 3.588104] cpuidle: using governor menu
<6>[ 3.589965] mmc0: Qualcomm MSM SDCC at 0x00000000a0400000 irq 24,0 dma 8
<6>[ 3.590484] mmc0: Platform slot type: N/A
<6>[ 3.590759] mmc0: 4 bit data mode enabled
<6>[ 3.591278] mmc0: 8 bit data mode disabled
<6>[ 3.591552] mmc0: MMC clock 144000 -> 49152000 Hz, PCLK 80000000 Hz
<6>[ 3.591827] mmc0: Slot eject status = 1
<6>[ 3.592437] mmc0: Power save feature enable = 1
<6>[ 3.592712] mmc0: DM non-cached buffer at ffa4a000, dma_addr 0x26f55000
<6>[ 3.593231] mmc0: DM cmd busaddr 0x26f55000, cmdptr busaddr 0x26f55300
<6>[ 3.594573] buzz_sdslot_switchvdd: Disabling SD slot power
<6>[ 3.595428] mmc1: Qualcomm MSM SDCC at 0x00000000a0500000 irq 26,102 dma 8
<6>[ 3.595733] mmc1: Platform slot type: SD
<6>[ 3.596221] mmc1: 4 bit data mode enabled
<6>[ 3.596496] mmc1: 8 bit data mode disabled
<6>[ 3.596984] mmc1: MMC clock 144000 -> 49152000 Hz, PCLK 80000000 Hz
<6>[ 3.597259] mmc1: Slot eject status = 1
<6>[ 3.597534] mmc1: Power save feature enable = 1
<6>[ 3.598022] mmc1: DM non-cached buffer at ffa4b000, dma_addr 0x26f56000
<6>[ 3.598327] mmc1: DM cmd busaddr 0x26f56000, cmdptr busaddr 0x26f56300
<7>[ 3.599487] Registered led device: amber
<7>[ 3.600006] Registered led device: green
<7>[ 3.600677] Registered led device: jogball-backlight
<7>[ 3.601135] Registered led device: button-backlight
<6>[ 3.601654] microp_led_probe: succeeded
<6>[ 3.604522] logger: created 256K log 'log_main'
<6>[ 3.605133] logger: created 256K log 'log_events'
<6>[ 3.605926] logger: created 256K log 'log_radio'
<6>[ 3.606445] logger: created 256K log 'log_system'
<6>[ 3.607299] zram: num_devices not specified. Using default: 1
<6>[ 3.607574] zram: Creating 1 devices ...
<6>[ 3.609008] GACT probability NOT on
<6>[ 3.609558] Mirror/redirect action on
<6>[ 3.609832] u32 classifier
<6>[ 3.610076] Actions configured
<6>[ 3.610595] Netfilter messages via NETLINK v0.30.
<6>[ 3.611083] nf_conntrack version 0.5.0 (4996 buckets, 19984 max)
<4>[ 3.611846] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
<4>[ 3.612518] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
<4>[ 3.613037] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
<6>[ 3.613647] ctnetlink v0.93: registering with nfnetlink.
<6>[ 3.614288] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
<6>[ 3.614593] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
<6>[ 3.615936] xt_time: kernel timezone is -0000
<6>[ 3.616363] IPv4 over IPv4 tunneling driver
<6>[ 3.617950] GRE over IPv4 tunneling driver
<6>[ 3.619628] ip_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 3.620452] arp_tables: (C) 2002 David S. Miller
<6>[ 3.620880] TCP cubic registered
<6>[ 3.621704] NET: Registered protocol family 10
<6>[ 3.626342] Mobile IPv6
<6>[ 3.626800] ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>[ 3.627410] IPv6 over IPv4 tunneling driver
<6>[ 3.630920] NET: Registered protocol family 17
<6>[ 3.631317] NET: Registered protocol family 15
<6>[ 3.632507] Bluetooth: RFCOMM socket layer initialized
<6>[ 3.633026] Bluetooth: RFCOMM ver 1.11
<6>[ 3.633361] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
<6>[ 3.633850] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
<6>[ 3.634796] clock_late_init() disabled 16 unused clocks
<6>[ 3.635345] [Port list] init()
<6>[ 3.635620] [Port list] Virtual Address for port_list: [f8149a48]
<6>[ 3.636108] [Port list] Physical Address for port_list: [849A48]
<6>[ 3.637756] cpufreq: cpu0 init at 480000 switching to 352000
<6>[ 3.642211] rs30000048:915823fc rs30000048:915823fc: setting system clock to 2013-12-16 11:43:36 UTC (1387194216)
<4>[ 3.643127] Warning: unable to open an initial console.
<6>[ 3.643981] Freeing init memory: 144K
<6>[ 3.918975] keychord: using input dev h2w headset for fevent
<6>[ 3.919464] keychord: using input dev buzz-keypad for fevent
<6>[ 3.926330] yaffs: dev is 32505859 name is "mtdblock3"
<6>[ 3.926757] yaffs: passed flags ""
<4>[ 3.927001] yaffs: Attempting MTD mount on 31.3, "mtdblock3"
<4>[ 4.099121] yaffs: restored from checkpoint
<4>[ 4.100067] yaffs_read_super: isCheckpointed 1
<6>[ 4.103546] yaffs: dev is 32505861 name is "mtdblock5"
<6>[ 4.104003] yaffs: passed flags ""
[COLOR="Red"]<4>[ 4.104248] yaffs: Attempting MTD mount on 31.5, "mtdblock5"
<4>[ 4.712463] block 725 is bad
<4>[ 4.744262] block 845 is bad
<4>[ 4.797912] block 1049 is bad[/COLOR]
<4>[ 18.353271] Partially written block 1006 detected
<4>[ 18.353942] Partially written block 1006 detected
<4>[ 18.354339] Partially written block 1006 detected
<4>[ 18.354766] Partially written block 1006 detected
<4>[ 18.355346] Partially written block 1006 detected
<4>[ 18.355773] Partially written block 1006 detected
<4>[ 18.356353] Partially written block 1006 detected
<4>[ 18.356781] Partially written block 1006 detected
<4>[ 18.357360] Partially written block 1006 detected
<4>[ 18.357788] Partially written block 1006 detected
<4>[ 18.358184] Partially written block 1006 detected
<4>[ 18.358795] Partially written block 1006 detected
<4>[ 18.359191] Partially written block 1006 detected
<4>[ 18.359802] Partially written block 1006 detected
<4>[ 18.360198] Partially written block 1006 detected
<4>[ 18.360595] Partially written block 1006 detected
<4>[ 18.361206] Partially written block 1006 detected
<4>[ 18.361633] Partially written block 1006 detected
<4>[ 18.362213] Partially written block 1006 detected
<4>[ 18.362640] Partially written block 1006 detected
<4>[ 18.363250] Partially written block 1006 detected
<4>[ 18.363677] Partially written block 1006 detected
<4>[ 18.364105] Partially written block 1006 detected
<4>[ 18.364715] Partially written block 1006 detected
<4>[ 18.460662] yaffs_read_super: isCheckpointed 0
<6>[ 18.461517] yaffs: dev is 32505860 name is "mtdblock4"
<6>[ 18.461791] yaffs: passed flags ""
<4>[ 18.462005] yaffs: Attempting MTD mount on 31.4, "mtdblock4"
<4>[ 18.521240] yaffs_read_super: isCheckpointed 0
<3>[ 20.180206] init: service 'console' requires console
<6>[ 20.258422] enabling adb
<6>[ 20.281280] [USB] msm_hsusb: disable pullup
<6>[ 20.293457] [USB] msm_hsusb: enable pullup
<6>[ 20.297027] [USB] suspend
<6>[ 20.311981] adb_open
<6>[ 20.482727] [USB] reset
<6>[ 20.483032] [USB] handle_notify_offline: notify offline
<6>[ 20.484069] adb_release
<6>[ 20.485015] [USB] portchange USB_SPEED_HIGH
<6>[ 20.485534] adb_open
<6>[ 20.642822] [USB] reset
<6>[ 20.645080] [USB] portchange USB_SPEED_HIGH
<6>[ 20.715698] warning: `rild' uses 32-bit capabilities (legacy support in use)
<6>[ 20.854614] android_usb gadget: high speed config #1: android
<6>[ 20.928436] [SMD]SMD: ch 0 0 -> 1
<6>[ 20.928771] [SMD]SMD: ch 0 1 -> 2
<6>[ 20.939819] [SMD]SMD: ch 38 0 -> 1
<6>[ 20.940155] [SMD]SMD: ch 38 1 -> 2
<6>[ 20.940368] [RIL] qmi: smd opened
<6>[ 20.942810] [RIL] qmi: ctl: wds use client_id 0x01
<6>[ 20.947113] [SMD]SMD: ch 39 0 -> 1
<6>[ 20.947448] [SMD]SMD: ch 39 1 -> 2
<6>[ 20.947875] [RIL] qmi: smd opened
<6>[ 20.948699] [RIL] qmi: ctl: wds use client_id 0x01
<6>[ 20.950500] [SMD]SMD: ch 40 0 -> 1
<6>[ 20.951080] [SMD]SMD: ch 40 1 -> 2
<6>[ 20.951324] [RIL] qmi: smd opened
<6>[ 20.952941] [RIL] qmi: ctl: wds use client_id 0x01
<6>[ 22.985412] [AUD][snd.c:snd_ioctl] snd_set_device 1 1 1
<6>[ 22.989074] [AUD][snd.c:snd_rpc_thread] snd_rpc_thread() start
<6>[ 22.989624] [AUD][snd.c:snd_rpc_thread] snd: rpc_reply status 0
<6>[ 22.992858] [AUD][snd.c:snd_ioctl] snd_set_volume 256 0 5
<6>[ 22.996887] [AUD][snd.c:snd_rpc_thread] snd: rpc_reply status 0
As you can see
<4>[ 4.104248] yaffs: Attempting MTD mount on 31.5, "mtdblock5"
<4>[ 4.712463] block 725 is bad
<4>[ 4.744262] block 845 is bad
<4>[ 4.797912] block 1049 is bad
Click to expand...
Click to collapse
Does that indicate bad blocks on SDCard ?

So i have reviewed your logcat and its not showing up anything that could make it bootloop :/ can you use nandroid manager to restore just the app data and see how it gets on for me? it shouldnt need to reboot to do it.

heavy_metal_man said:
So i have reviewed your logcat and its not showing up anything that could make it bootloop :/ can you use nandroid manager to restore just the app data and see how it gets on for me? it shouldnt need to reboot to do it.
Click to expand...
Click to collapse
Okay,thanks,I restored some user apps and system apps (including data).Some apps are working fine and restored back to previous state including CM Settings but some apps got messed up and data didn't get restored.
What should be the next move ?

optimusodd said:
Okay,thanks,I restored some user apps and system apps (including data).Some apps are working fine and restored back to previous state including CM Settings but some apps got messed up and data didn't get restored.
What should be the next move ?
Click to expand...
Click to collapse
Well that tells us that the nandroid back up has became corrupted somehow, or your sdcard partition is not the same as your nandroids. If it's corruption your pretty stuffed and will have to just start fresh, but I would first double check your partitioning and then attempt a final restore with nandroid manager. If it fails then delete the apps that don't work data and keep what works I suppose :/
Sent from my HTC Sensation XE with Beats Audio Z715e using Tapatalk

heavy_metal_man said:
Well that tells us that the nandroid back up has became corrupted somehow, or your sdcard partition is not the same as your nandroids. If it's corruption your pretty stuffed and will have to just start fresh, but I would first double check your partitioning and then attempt a final restore with nandroid manager.
Click to expand...
Click to collapse
Thanks for the reply.
Huh,What do you mean by sdcard partition is not the same ?
Okay let me go into a little more detail.Few months back I was using 8GB card.And the nandoid backup I want to restore was taken on that card.
MTD partition size : 110 10
Ext3 :512 MB
Now I am using 16GB card with 1GB Ext3 partition.
No custom MTD partition.
Do I need to run custom MTD script ?
SDCard partition could be a problem if I was using a card of less capacity.But as both the memory capacity and the size of Ext3 partition are larger in this scenario so I think partition should not be a problem.
Correct me if I am wrong
Furthermore,the same nandroid backup got restored perfectly using the new card before that kernel and radio thing.Gah!

optimusodd said:
Thanks for the reply.
Huh,What do you mean by sdcard partition is not the same ?
Okay let me go into a little more detail.Few months back I was using 8GB card.And the nandoid backup I want to restore was taken on that card.
MTD partition size : 110 10
Ext3 :512 MB
Now I am using 16GB card with 1GB Ext3 partition.
No custom MTD partition.
Do I need to run custom MTD script ?
SDCard partition could be a problem if I was using a card of less capacity.But as both the memory capacity and the size of Ext3 partition are larger in this scenario so I think partition should not be a problem.
Correct me if I am wrong
Furthermore,the same nandroid backup got restored perfectly using the new card before that kernel and radio thing.Gah!
Click to expand...
Click to collapse
If you made the nandroid with a custom mtd the you had best restore it with a custom mtd. I'm not 100% sure how it's done or the theory around it though, it's been a long time since I've had to do such things.
Sent from my HTC Sensation XE with Beats Audio Z715e using Tapatalk

heavy_metal_man said:
If you made the nandroid with a custom mtd the you had best restore it with a custom mtd. I'm not 100% sure how it's done or the theory around it though, it's been a long time since I've had to do such things.
Sent from my HTC Sensation XE with Beats Audio Z715e using Tapatalk
Click to expand...
Click to collapse
Alright,buddy,I give it a try.:fingers-crossed:

Happy New Year! Well, sorry for being a bit unresponsive - I'm really late (and still have no time) - just a quick $ 0.02: if I'm not totally mistaken it makes a huge difference if you use custom mtd partitions. The recovery makes an image of the partitions which means on restore the same size is expected (which would also apply to your sd-ext...)
Best bet should be: make a restore with the old settings (custom mtd partitions and sd-ext) and sequentially backup the stuff in other ways than with a nandroid backup. See if it works. Alternatively you could extract the stuff out of the backup - but this might become really painful...
Hope this helps.
BTW: my problem you were refering to has been totally different as I've never been stuck on boot - I had massive random reboots - so this was another story...

heavy_metal_man said:
If you made the nandroid with a custom mtd the you had best restore it with a custom mtd. I'm not 100% sure how it's done or the theory around it though, it's been a long time since I've had to do such things.
Click to expand...
Click to collapse
eventcom said:
if I'm not totally mistaken it makes a huge difference if you use custom mtd partitions. The recovery makes an image of the partitions which means on restore the same size is expected (which would also apply to your sd-ext...)
Click to expand...
Click to collapse
Hello guys,Belated Happy New Year!!!Sorry for the late response.I was out of town and didn't have a chance to check the thread until today.I had finally got it working on 29th Dec after 15 days tearing my hair out trying to fix it.
Ah,after trying a lot of things and epic struggle finally some peace and quiet.:victory:
Thank you very much "heavy_metal_man" for your continued support and kind cooperation.I couldn't have done this without your inexhaustible support.I really appreciate it.
Thank you "eventcom" for the reply.I appreciate it.Though you were a bit late but you got it right.Probably it was the MTD thing.
I am not sure what exactly happened and what did the trick in the end.In all probability it was MTD partition thing which was messing up.
Not is case of Ext partition though.Because as I have mentioned my previous ext3 was 512 MB while now I am using 1GB Ext3 partition.
So I think Restore with old MTD settings and Ext partition >/= previous Ext partition should do the job.
Steps followed:
>Unroot and S-ON
http://forum.xda-developers.com/showthread.php?p=22832599
>Root
http://forum.xda-developers.com/showthread.php?t=1145035&nocache=1&nocache=1
>Data Wipe - Factory Reset
>Wipe Cache Partition
>Format /cache
>Format /system
>Format /data
>Wipe cache partition
>Wipe Dalvik Cache
>Create text file with custom MTD partition settings you had while taking Nandroid Backup
>Go to Recovery
>Mounts and Storage
>Format /cache
>Format /system
>Format /data
>Wipe Data / Factory Reset
>Flash "recovery-v1.5.8-Beta-CustomMTD_S.zip"
>Go to Advanced
>Reboot Recovery
>Restore Nandroid Backup
>Fix permissions
>Without restarting, flash "boot-v1.5.8-Beta-CustomMTD_S.zip"
>Reboot device
After Nandroid Restore Superuser started malfunctioning.Apps (including Titanium Backup) requiring ROOT access were not getting required permissions while it was being displayed that Superuser had granted the permissions.Anyway,was able to resolve that problem somehow and now my device is working perfectly.:victory:

Problems with all 2.4Ghz wifi networks

Hi, I have a problem with all wifi 2.4ghz networks, I do not connect to any of them, I tried changing the password, with different routers. Factory reset google pixel and the problem persists.
Sometimes the 2.4ghz networks work magically for about three days and then it stops working without making any changes.
I leave a trace of the log to see if you can help me with my problem:
[ 428.029397] c1 7483 wlan: [7483:E :SME] csrSendJoinReqMsg: 13756: Connecting to ssid:ATU bssid: 38:60:77:9e:??:?? rssi: -42 channel: 3 country_code: ES
[ 428.029836] c1 7483 wlan: [7483:E :WDA] wma_create_peer: Created peer with peer_addr 38:60:77:9e:??:?? vdev_id 0, peer_count - 1
[ 429.198654] c0 7483 wlan: [7483:E E ] limProcessAuthFailureTimeout: 4227: received AUTH failure timeout in sessionid 0 limMlmstate 7 limSmeState 5
[ 429.199876] c0 7483 wlan: [7483:E E ] limProcessMlmAuthCnf: 795: Auth Failure occurred.
[ 429.204013] c0 7483 wlan: [7483:E :WDA] wma_remove_peer: Removed peer with addr 38:60:77:9e:??:?? vdevid 0 peer_count 0
[ 429.213566] c0 7483 wlan: connection failed with 38:60:77:9e:??:?? result:3 and Status:7
[ 429.213949] c0 7483 wlan: connection failed with 38:60:77:9e:??:?? result:1 and Status:9
[ 429.214186] c0 7483 wlan: [7483:E :HDD] hdd_AssociationCompletionHandler: send connect failure to nl80211: for bssid 38:60:77:9e:??:?? result:1 and Status:9 reasonCode 1
[ 429.231857] c1 1400 wlan: [1400:E :HDD] vos_flush_logs: Triggering bug report: type:0, indicator=1 reason_code=0 dump_trace=0x3
[ 429.246800] c1 7481 wlan: [7481:E :HDD] send_flush_completion_to_user: Sending flush done to userspace
[ 430.633523] c0 33 cnss_wlan_pci 0000:01:00.0: Refused to change power state, currently in D3
[ 430.693767] c0 33 cnss_wlan_pci 0000:01:00.0: enabling device (0000 -> 0002)
[ 432.156886] c0 33 cnss_wlan_pci 0000:01:00.0: Refused to change power state, currently in D3
[ 432.217113] c0 33 cnss_wlan_pci 0000:01:00.0: enabling device (0000 -> 0002)
[ 434.606813] c1 513 cnss_wlan_pci 0000:01:00.0: Refused to change power state, currently in D3
[ 434.670350] c1 513 cnss_wlan_pci 0000:01:00.0: enabling device (0000 -> 0002)
[ 437.082498] c0 1413 wlan: [1413:E :WDA] scan complete - scan_id a00a, vdev_id 0
[ 437.084143] c0 7483 wlan: [7483:E :SME] Found 16 BSS, statusCode 0
[ 454.593387] c2 336 cnss_wlan_pci 0000:01:00.0: Refused to change power state, currently in D3
[ 454.650798] c2 336 cnss_wlan_pci 0000:01:00.0: enabling device (0000 -> 0002)
[ 457.057173] c0 33 wlan: [33:E :WDA] scan complete - scan_id a00b, vdev_id 0
[ 457.057579] c0 7483 wlan: [7483:E :SME] Found 19 BSS, statusCode 0

How are you sure about the 2.4GHz problem? isn't it for 5GHz?

how much have you modified your phone.
Which kernel are you on?
I dont recall factory reset replacing the kernel with stock.

Yes, I only happen with the 2.4ghz networks, the 5ghz networks work perfect, I have tried to restore factory and the problem persists.

Still didn't answer question
xperiatomaja said:
Yes, I only happen with the 2.4ghz networks, the 5ghz networks work perfect, I have tried to restore factory and the problem persists.
Click to expand...
Click to collapse
?????
how much have you modified your phone.
Which kernel are you on?

parakleet said:
?????
how much have you modified your phone.
Which kernel are you on?
Click to expand...
Click to collapse
full Stock

If you are currently stock and have always been stock im guessing you are probably looking at an RMA.
The only issues i could find dealt with people that modified the kernel.
You might be having some straight up hardware failure.

Native Linux (postmarketOS) on Tab 3?

I've been trying to port postmarketOS to this tablet however I need some help. (https://wiki.postmarketos.org/wiki/Samsung_Galaxy_Tab_3_10.1_3G_(samsung-santos103g))
My progress: I compiled the kernel successfully (from santos10-dev on GitHub), however due to the initramfs being compressed with gzip in postmarketOS the kernel crashes with RAMDISK: gzip decompressor not configured!, so I enabled CONFIG_RD_GZIP, but now the kernel won't load at all (on both of my tablets). I also tried the maximum-attention hook because the 3g variant has a vibration motor but nothing happened and to be sure that the hook works I took the script from the hook and tried it in TWRP out and it vibrated.
The next thing I did is analyze the boot.img from postmarketOS and LineageOS (from nels83) and noticed that the boot.img contains a file called ramdisk. In the LineageOS boot.img the ramdisk is compressed with LZMA and in the postmarketOS boot.img the file is compressed with gzip, but the kernel crashed with the gzip-compressed ramdisk, so the kernel did load, right?
I also made a 619k ohm UART adapter and I'm getting output but after the logo shows on the tablet nothing more will output. The pmOS wiki says that I need to add console=ttyS0,115200n8 to CONFIG_CMDLINE but in TWRP and LineageOS, there is no ttySX in /dev, so I enabled serial-related kernel configs and still nothing :/
Im not good at programming and running native Linux on this tablet would be so cool! And due to this tablet having MHL this could be a really nice portable PC (even though it only has 1GB of RAM...)
Here are a few logs I got:
Spoiler: Kernel crashing without CONFIG_RD_GZIP enabled (from /proc/last_kmsg)
Code:
[ 0.297125] C0 [ swapper/0] SPID not found in kernel command line.
[ 0.615822] C1 [ swapper/0] pci 0000:00:03.1: unsupported PM cap regs version (4)
[ 0.638509] C2 [ swapper/0] PMU DRIVER BEFORE PROBE
[ 0.875526] C3 [ ia_watchdog] intel_scu_watchdog: intel_scu_watchdog: intel_scu_stop
[ 1.523324] C2 [ swapper/0] Request for hsu(64) GPIO fails
[ 1.524084] C2 [ swapper/0] Request for hsu(67) GPIO fails
[ 1.632454] C2 [ swapper/0] penwell_otg 0000:00:02.3: PHY can't enter low power mode when UDC is in idle mode
[ 1.772449] C2 [ swapper/0] ehci_hcd 0000:00:06.5: can't setup
[ 1.772788] C2 [ swapper/0] ehci_hcd 0000:00:06.5: init 0000:00:06.5 fail, -19
[ 2.669666] C2 [ swapper/0] i2c_dw_pci_probe: invalid bus index 259
[ 2.675593] C2 [ swapper/0] i2c_dw_pci_probe: invalid bus index 261
[ 2.726561] C2 [ swapper/0] i2c i2c-9: sendbytes: NAK bailout.
[ 2.726601] C2 [ swapper/0] Failed to stmpe811 write, reg: 3
[ 2.951859] C2 [ swapper/0] tc35876x_vid_detect: It seems to use Intel Stand-alone Bootloader...
[ 3.110758] C2 [ swapper/0] bh1730fvc_test_device : POWER ON 0, 3
[ 3.110777] C2 [ swapper/0] bh1730fvc_test_device : slave addr : 0x29
[ 3.124751] C3 [ swapper/0] power_supply sec-fuelgauge: driver failed to report `status' property: 4294967274
[ 3.131543] C3 [ kworker/3:0] power_supply sec-fuelgauge: driver failed to report `status' property: 4294967274
[ 3.315524] C0 [ swapper/0] power_supply sec-charger: driver failed to report `power_now' property: 4294967274
[ 3.329554] C0 [ kworker/0:1] power_supply sec-charger: driver failed to report `power_now' property: 4294967274
[ 5.101678] C2 [ swapper/0] RAMDISK: gzip decompressor not configured!
[ 5.101700] C2 [ swapper/0] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 5.101722] C2 [ swapper/0] IP: [< (null)>] (null)
[ 5.101740] C2 [ swapper/0] *pdpt = 0000000000000000 *pde = 20676e696c6c0a0d
[ 5.101764] C2 [ swapper/0] Oops: 0010 [#1] PREEMPT SMP
[ 5.101787] C2 [ swapper/0]
[ 5.101803] C2 [ swapper/0] Pid: 1, comm: swapper/0 Tainted: G W 3.4.34-lineage #1-postmarketOS Intel Corporation CloverTrail/CloverTrail
[ 5.101835] C2 [ swapper/0] EIP: 0060:[<00000000>] EFLAGS: 00010246 CPU: 2
[ 5.101851] C2 [ swapper/0] EIP is at 0x0
[ 5.101864] C2 [ swapper/0] EAX: 00000000 EBX: 00000000 ECX: c1beff11 EDX: 00000000
[ 5.101880] C2 [ swapper/0] ESI: ef596c00 EDI: 00000000 EBP: c0077fa4 ESP: c0077f5c
[ 5.101896] C2 [ swapper/0] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 5.101911] C2 [ swapper/0] CR0: 8005003b CR2: 00000000 CR3: 01c7f000 CR4: 000007f0
[ 5.101927] C2 [ swapper/0] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 5.101942] C2 [ swapper/0] DR6: ffff0ff0 DR7: 00000400
[ 5.101958] C2 [ swapper/0] Process swapper/0 (pid: 1, ti=c0076000 task=c0078000 task.ti=c0076000)
[ 5.101972] C2 [ swapper/0] Stack:
[ 5.101984] C2 [ swapper/0] c1bf026c c1beff4c 00000000 00000000 c1befef5 00100000 61800000 c1a1bf01
[ 5.102031] C2 [ swapper/0] 00000000 00000000 00000000 00000001 c0077fa4 c1a6288d 5c2d2f7c 00000000
[ 5.102076] C2 [ swapper/0] 00000000 c1a1c378 c0077fc4 c1bf0565 c1a1bef8 00006180 00000100 c1a1bef8
[ 5.102121] C2 [ swapper/0] Call Trace:
[ 5.102147] C2 [ swapper/0] [<c1bf026c>] ? rd_load_image+0x2a5/0x4ce
[ 5.102168] C2 [ swapper/0] [<c1beff4c>] ? compr_fill+0x3b/0x3b
[ 5.102189] C2 [ swapper/0] [<c1befef5>] ? prepare_namespace+0x176/0x176
[ 5.102210] C2 [ swapper/0] [<c1bf0565>] initrd_load+0x3a/0x2eb
[ 5.102230] C2 [ swapper/0] [<c1befe3c>] prepare_namespace+0xbd/0x176
[ 5.102250] C2 [ swapper/0] [<c1bef9de>] kernel_init+0x18b/0x190
[ 5.102269] C2 [ swapper/0] [<c1bef853>] ? do_one_initcall+0x10b/0x10b
[ 5.102291] C2 [ swapper/0] [<c1837cba>] kernel_thread_helper+0x6/0x10
[ 5.102304] C2 [ swapper/0] Code: Bad EIP value.
[ 5.102327] C2 [ swapper/0] EIP: [<00000000>] 0x0 SS:ESP 0068:c0077f5c
[ 5.102348] C2 [ swapper/0] CR2: 0000000000000000
[ 5.102422] C2 [ swapper/0] Board Information: santos10wifi - Samsung Board (0xAC84D59E): 08, cpu Intel(R) Atom(TM) CPU Z2560 @ 1.60GHz stepping 1
[ 5.102457] C2 [ swapper/0] ---[ end trace a0c19de72eec37db ]---
[ 5.102522] C2 [ swapper/0] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
[ 5.102527] C2 [ swapper/0]
[ 5.102540] C2 [ swapper/0] sending NMI to all CPUs:
[ 5.102557] C3 [ swapper/3] NMI backtrace for cpu 3
[ 5.102566] C3 [ swapper/3]
[ 5.102578] C3 [ swapper/3] Pid: 0, comm: swapper/3 Tainted: G D W 3.4.34-lineage #1-postmarketOS Intel Corporation CloverTrail/CloverTrail
[ 5.102604] C3 [ swapper/3] EIP: 0060:[<c12feec4>] EFLAGS: 00000046 CPU: 3
[ 5.102620] C3 [ swapper/3] EIP is at soc_s0ix_idle+0x164/0x4f0
[ 5.102633] C3 [ swapper/3] EAX: 00000052 EBX: f00a4000 ECX: 00000001 EDX: 00000000
[ 5.102646] C3 [ swapper/3] ESI: 00000052 EDI: 00000000 EBP: f00a5f28 ESP: f00a5ef4
[ 5.102659] C3 [ swapper/3] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 5.102672] C3 [ swapper/3] CR0: 8005003b CR2: 00000000 CR3: 01c7f000 CR4: 000007f0
[ 5.102686] C3 [ swapper/3] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 5.102699] C3 [ swapper/3] DR6: ffff0ff0 DR7: 00000400
[ 5.102712] C3 [ swapper/3] Process swapper/3 (pid: 0, ti=f00a4000 task=c007f380 task.ti=f00a4000)
[ 5.102724] C3 [ swapper/3] Stack:
[ 5.102733] C3 [ swapper/3] 00000281 c1b53980 00000040 00000003 00000006 00000000 00000052 00000000
[ 5.102768] C3 [ swapper/3] 00000052 00000003 c1b97ba0 000001c8 00000001 f00a5f38 c1570eac c1b97ba0
[ 5.102802] C3 [ swapper/3] 2c6a5255 f00a5f5c c157153a c1b97ba0 fffffff9 00000006 f0c1425c f00a4000
[ 5.102837] C3 [ swapper/3] Call Trace:
[ 5.102855] C3 [ swapper/3] [<c1570eac>] cpuidle_enter+0xc/0x10
[ 5.102873] C3 [ swapper/3] [<c157153a>] cpuidle_wrap_enter+0x2a/0xa0
[ 5.102889] C3 [ swapper/3] [<c15715c2>] cpuidle_enter_tk+0x12/0x20
[ 5.102907] C3 [ swapper/3] [<c1570ea0>] ? cpufreq_get_measured_perf+0xe0/0xe0
[ 5.102923] C3 [ swapper/3] [<c1571202>] cpuidle_idle_call+0x92/0x2e0
[ 5.102942] C3 [ swapper/3] [<c106c08b>] ? atomic_notifier_call_chain+0x3b/0x50
[ 5.102960] C3 [ swapper/3] [<c100ee94>] cpu_idle+0x94/0xe0
[ 5.102977] C3 [ swapper/3] [<c182b920>] start_secondary+0x1a8/0x1ad
[ 5.102989] C3 [ swapper/3] Code: 00 00 89 e3 31 d2 81 e3 00 e0 ff ff 89 d1 8d 43 08 0f 01 c8 0f ae f0 89 f6 8b 43 08 a8 08 75 0b b9 01 00 00 00 8b 45 e4 0f 01 c9 <8b> 4d e8 85 c9 0f 85 c1 01 00 00 83 7d e4 52 0f 85 47 03 00 00
[ 5.103177] C3 [ swapper/3] Call Trace:
[ 5.103192] C3 [ swapper/3] [<c1570eac>] cpuidle_enter+0xc/0x10
[ 5.103208] C3 [ swapper/3] [<c157153a>] cpuidle_wrap_enter+0x2a/0xa0
[ 5.103225] C3 [ swapper/3] [<c15715c2>] cpuidle_enter_tk+0x12/0x20
[ 5.103241] C3 [ swapper/3] [<c1570ea0>] ? cpufreq_get_measured_perf+0xe0/0xe0
[ 5.103258] C3 [ swapper/3] [<c1571202>] cpuidle_idle_call+0x92/0x2e0
[ 5.103275] C3 [ swapper/3] [<c106c08b>] ? atomic_notifier_call_chain+0x3b/0x50
[ 5.103291] C3 [ swapper/3] [<c100ee94>] cpu_idle+0x94/0xe0
[ 5.103307] C3 [ swapper/3] [<c182b920>] start_secondary+0x1a8/0x1ad
[ 5.103319] C2 [ swapper/0] NMI backtrace for cpu 2
[ 5.103329] C2 [ swapper/0]
[ 5.103341] C2 [ swapper/0] Pid: 1, comm: swapper/0 Tainted: G D W 3.4.34-lineage #1-postmarketOS Intel Corporation CloverTrail/CloverTrail
[ 5.103361] C2 [ swapper/0] EIP: 0060:[<c12bed71>] EFLAGS: 00000206 CPU: 2
[ 5.103374] C2 [ swapper/0] EIP is at __const_udelay+0x1/0x20
[ 5.103385] C2 [ swapper/0] EAX: 00418958 EBX: 00002710 ECX: c1b563e0 EDX: 00000c00
[ 5.103396] C2 [ swapper/0] ESI: c0078000 EDI: c0078000 EBP: c0077da8 ESP: c0077d98
[ 5.103408] C2 [ swapper/0] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 5.103419] C2 [ swapper/0] CR0: 8005003b CR2: ffffffd5 CR3: 01c7f000 CR4: 000007f0
[ 5.103430] C2 [ swapper/0] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 5.103440] C2 [ swapper/0] DR6: ffff0ff0 DR7: 00000400
[ 5.103450] C2 [ swapper/0] Process swapper/0 (pid: 1, ti=c0076000 task=c0078000 task.ti=c0076000)
[ 5.103459] C2 [ swapper/0] Stack:
[ 5.103467] C2 [ swapper/0] c0077da8 c1022e12 c1a2ae87 c0078274 c0077dc0 c182f47c 00000001 c0078274
[ 5.103495] C2 [ swapper/0] c0078000 c0078000 c0077e0c c104b20e c1a2fed4 00000009 c1b68040 c0077e04
[ 5.103523] C2 [ swapper/0] c10487b0 00000000 01c8aa60 00020f8b 00000001 c1b6f5c0 c1a3d766 c0078274
[ 5.103551] C2 [ swapper/0] Call Trace:
[ 5.103565] C2 [ swapper/0] [<c1022e12>] ? arch_trigger_all_cpu_backtrace+0x62/0x80
[ 5.103579] C2 [ swapper/0] [<c182f47c>] panic+0x87/0x16f
[ 5.103593] C2 [ swapper/0] [<c104b20e>] do_exit+0x81e/0x820
[ 5.103607] C2 [ swapper/0] [<c10487b0>] ? kmsg_dump+0xb0/0xe0
[ 5.103621] C2 [ swapper/0] [<c100676d>] oops_end+0x7d/0xc0
[ 5.103635] C2 [ swapper/0] [<c1029946>] no_context+0x106/0x1e0
[ 5.103649] C2 [ swapper/0] [<c1029ad5>] __bad_area_nosemaphore+0xb5/0x140
[ 5.103663] C2 [ swapper/0] [<c1046894>] ? __call_console_drivers+0xa4/0xb0
[ 5.103677] C2 [ swapper/0] [<c106be83>] ? up+0x13/0x50
[ 5.103689] C2 [ swapper/0] [<c106be9a>] ? up+0x2a/0x50
[ 5.103702] C2 [ swapper/0] [<c1047421>] ? console_unlock+0x211/0x2f0
[ 5.103716] C2 [ swapper/0] [<c1029e20>] ? vmalloc_sync_all+0x10/0x10
[ 5.103730] C2 [ swapper/0] [<c1029b77>] bad_area_nosemaphore+0x17/0x20
[ 5.103744] C2 [ swapper/0] [<c102a0aa>] do_page_fault+0x28a/0x410
[ 5.103759] C2 [ swapper/0] [<c1836984>] ? _raw_spin_unlock_irqrestore+0x24/0x50
[ 5.103774] C2 [ swapper/0] [<c1029e20>] ? vmalloc_sync_all+0x10/0x10
[ 5.103788] C2 [ swapper/0] [<c1029e20>] ? vmalloc_sync_all+0x10/0x10
[ 5.103801] C2 [ swapper/0] [<c18374ab>] error_code+0x5f/0x64
[ 5.103814] C2 [ swapper/0] [<c1beff11>] ? error+0x1c/0x1c
[ 5.103828] C2 [ swapper/0] [<c1bf00d8>] ? rd_load_image+0x111/0x4ce
[ 5.103842] C2 [ swapper/0] [<c1029e20>] ? vmalloc_sync_all+0x10/0x10
[ 5.103856] C2 [ swapper/0] [<c1bf026c>] ? rd_load_image+0x2a5/0x4ce
[ 5.103869] C2 [ swapper/0] [<c1beff4c>] ? compr_fill+0x3b/0x3b
[ 5.103883] C2 [ swapper/0] [<c1befef5>] ? prepare_namespace+0x176/0x176
[ 5.103897] C2 [ swapper/0] [<c1bf0565>] initrd_load+0x3a/0x2eb
[ 5.103910] C2 [ swapper/0] [<c1befe3c>] prepare_namespace+0xbd/0x176
[ 5.103924] C2 [ swapper/0] [<c1bef9de>] kernel_init+0x18b/0x190
[ 5.103937] C2 [ swapper/0] [<c1bef853>] ? do_one_initcall+0x10b/0x10b
[ 5.103951] C2 [ swapper/0] [<c1837cba>] kernel_thread_helper+0x6/0x10
[ 5.103960] C2 [ swapper/0] Code: 26 00 c7 05 c0 58 b9 c1 70 ec 2b c1 5d c3 8d b4 26 00 00 00 00 8d 74 26 00 90 55 89 e5 3e 8d 74 26 00 ff 15 c0 58 b9 c1 5d c3 55 <c1> e0 02 64 8b 15 9c 41 c7 c1 8d 14 92 89 e5 8d 14 92 f7 e2 8d
[ 5.104111] C2 [ swapper/0] Call Trace:
[ 5.104123] C2 [ swapper/0] [<c1022e12>] ? arch_trigger_all_cpu_backtrace+0x62/0x80
[ 5.104136] C2 [ swapper/0] [<c182f47c>] panic+0x87/0x16f
[ 5.104149] C2 [ swapper/0] [<c104b20e>] do_exit+0x81e/0x820
[ 5.104162] C2 [ swapper/0] [<c10487b0>] ? kmsg_dump+0xb0/0xe0
[ 5.104175] C2 [ swapper/0] [<c100676d>] oops_end+0x7d/0xc0
[ 5.104188] C2 [ swapper/0] [<c1029946>] no_context+0x106/0x1e0
[ 5.104202] C2 [ swapper/0] [<c1029ad5>] __bad_area_nosemaphore+0xb5/0x140
[ 5.104215] C2 [ swapper/0] [<c1046894>] ? __call_console_drivers+0xa4/0xb0
[ 5.104229] C2 [ swapper/0] [<c106be83>] ? up+0x13/0x50
[ 5.104241] C2 [ swapper/0] [<c106be9a>] ? up+0x2a/0x50
[ 5.104253] C2 [ swapper/0] [<c1047421>] ? console_unlock+0x211/0x2f0
[ 5.104267] C2 [ swapper/0] [<c1029e20>] ? vmalloc_sync_all+0x10/0x10
[ 5.104281] C2 [ swapper/0] [<c1029b77>] bad_area_nosemaphore+0x17/0x20
[ 5.104294] C2 [ swapper/0] [<c102a0aa>] do_page_fault+0x28a/0x410
[ 5.104308] C2 [ swapper/0] [<c1836984>] ? _raw_spin_unlock_irqrestore+0x24/0x50
[ 5.104324] C2 [ swapper/0] [<c1029e20>] ? vmalloc_sync_all+0x10/0x10
[ 5.104337] C2 [ swapper/0] [<c1029e20>] ? vmalloc_sync_all+0x10/0x10
[ 5.104350] C2 [ swapper/0] [<c18374ab>] error_code+0x5f/0x64
[ 5.104363] C2 [ swapper/0] [<c1beff11>] ? error+0x1c/0x1c
[ 5.104376] C2 [ swapper/0] [<c1bf00d8>] ? rd_load_image+0x111/0x4ce
[ 5.104389] C2 [ swapper/0] [<c1029e20>] ? vmalloc_sync_all+0x10/0x10
[ 5.104403] C2 [ swapper/0] [<c1bf026c>] ? rd_load_image+0x2a5/0x4ce
[ 5.104417] C2 [ swapper/0] [<c1beff4c>] ? compr_fill+0x3b/0x3b
[ 5.104430] C2 [ swapper/0] [<c1befef5>] ? prepare_namespace+0x176/0x176
[ 5.104444] C2 [ swapper/0] [<c1bf0565>] initrd_load+0x3a/0x2eb
[ 5.104457] C2 [ swapper/0] [<c1befe3c>] prepare_namespace+0xbd/0x176
[ 5.104470] C2 [ swapper/0] [<c1bef9de>] kernel_init+0x18b/0x190
[ 5.104484] C2 [ swapper/0] [<c1bef853>] ? do_one_initcall+0x10b/0x10b
[ 5.104496] C2 [ swapper/0] [<c1837cba>] kernel_thread_helper+0x6/0x10
[ 5.104514] C1 [ swapper/1] NMI backtrace for cpu 1
[ 5.104538] C1 [ swapper/1]
[ 5.104561] C1 [ swapper/1] Pid: 0, comm: swapper/1 Tainted: G D W 3.4.34-lineage #1-postmarketOS Intel Corporation CloverTrail/CloverTrail
[ 5.104604] C1 [ swapper/1] EIP: 0060:[<c12fece1>] EFLAGS: 00000046 CPU: 1
[ 5.104632] C1 [ swapper/1] EIP is at intel_idle+0x91/0x110
[ 5.104652] C1 [ swapper/1] EAX: 00000000 EBX: 00000001 ECX: 00000001 EDX: 00000000
[ 5.104674] C1 [ swapper/1] ESI: 00000002 EDI: 00000000 EBP: f0069f28 ESP: f0069f14
[ 5.104696] C1 [ swapper/1] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 5.104717] C1 [ swapper/1] CR0: 8005003b CR2: 00000000 CR3: 01c7f000 CR4: 000007f0
[ 5.104738] C1 [ swapper/1] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 5.104758] C1 [ swapper/1] DR6: ffff0ff0 DR7: 00000400
[ 5.104780] C1 [ swapper/1] Process swapper/1 (pid: 0, ti=f0068000 task=c007bc80 task.ti=f0068000)
[ 5.104799] C1 [ swapper/1] Stack:
[ 5.104814] C1 [ swapper/1] 00000004 00000001 c1b97ba0 0000004c 00000001 f0069f38 c1570eac c1b97ba0
[ 5.104871] C1 [ swapper/1] 2c48130b f0069f5c c157153a c1b97ba0 fffffffe 00000001 f0bfe25c f0068000
[ 5.104926] C1 [ swapper/1] c1be6174 f0bfe25c f0069f68 c15715c2 c1570ea0 f0069f90 c1571202 c106c08b
[ 5.104982] C1 [ swapper/1] Call Trace:
[ 5.105014] C1 [ swapper/1] [<c1570eac>] cpuidle_enter+0xc/0x10
[ 5.105042] C1 [ swapper/1] [<c157153a>] cpuidle_wrap_enter+0x2a/0xa0
[ 5.105070] C1 [ swapper/1] [<c15715c2>] cpuidle_enter_tk+0x12/0x20
[ 5.105097] C1 [ swapper/1] [<c1570ea0>] ? cpufreq_get_measured_perf+0xe0/0xe0
[ 5.105125] C1 [ swapper/1] [<c1571202>] cpuidle_idle_call+0x92/0x2e0
[ 5.105154] C1 [ swapper/1] [<c106c08b>] ? atomic_notifier_call_chain+0x3b/0x50
[ 5.105182] C1 [ swapper/1] [<c100ee94>] cpu_idle+0x94/0xe0
[ 5.105211] C1 [ swapper/1] [<c182b920>] start_secondary+0x1a8/0x1ad
[ 5.105230] C1 [ swapper/1] Code: e2 08 75 27 31 d2 83 c0 08 89 d1 0f 01 c8 0f ae f0 89 f6 89 e0 25 00 e0 ff ff 8b 40 08 a8 08 75 0a b9 01 00 00 00 89 f8 0f 01 c9 <e8> 9a 24 dd ff 66 83 3d 2c 9d b5 c1 00 75 60 85 35 98 7b b9 c1
[ 5.105535] C1 [ swapper/1] Call Trace:
[ 5.105559] C1 [ swapper/1] [<c1570eac>] cpuidle_enter+0xc/0x10
[ 5.105585] C1 [ swapper/1] [<c157153a>] cpuidle_wrap_enter+0x2a/0xa0
[ 5.105612] C1 [ swapper/1] [<c15715c2>] cpuidle_enter_tk+0x12/0x20
[ 5.105638] C1 [ swapper/1] [<c1570ea0>] ? cpufreq_get_measured_perf+0xe0/0xe0
[ 5.105666] C1 [ swapper/1] [<c1571202>] cpuidle_idle_call+0x92/0x2e0
[ 5.105693] C1 [ swapper/1] [<c106c08b>] ? atomic_notifier_call_chain+0x3b/0x50
[ 5.105719] C1 [ swapper/1] [<c100ee94>] cpu_idle+0x94/0xe0
[ 5.105745] C1 [ swapper/1] [<c182b920>] start_secondary+0x1a8/0x1ad
[ 5.105765] C0 [ swapper/0] NMI backtrace for cpu 0
[ 5.105781] C0 [ swapper/0]
[ 5.105797] C0 [ swapper/0] Pid: 0, comm: swapper/0 Tainted: G D W 3.4.34-lineage #1-postmarketOS Intel Corporation CloverTrail/CloverTrail
[ 5.105829] C0 [ swapper/0] EIP: 0060:[<c12feec4>] EFLAGS: 00000046 CPU: 0
[ 5.105848] C0 [ swapper/0] EIP is at soc_s0ix_idle+0x164/0x4f0
[ 5.105864] C0 [ swapper/0] EAX: 00000052 EBX: c1b4c000 ECX: 00000001 EDX: 00000000
[ 5.105882] C0 [ swapper/0] ESI: 00000052 EDI: 00000000 EBP: c1b4df48 ESP: c1b4df14
[ 5.105899] C0 [ swapper/0] DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
[ 5.105916] C0 [ swapper/0] CR0: 8005003b CR2: ffe64000 CR3: 01c7f000 CR4: 000007f0
[ 5.105934] C0 [ swapper/0] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[ 5.105950] C0 [ swapper/0] DR6: ffff0ff0 DR7: 00000400
[ 5.105967] C0 [ swapper/0] Process swapper/0 (pid: 0, ti=c1b4c000 task=c1b52060 task.ti=c1b4c000)
[ 5.105983] C0 [ swapper/0] Stack:
[ 5.105994] C0 [ swapper/0] 00000001 c1b53980 00000040 00000007 00000007 00000000 00000052 00000000
[ 5.106039] C0 [ swapper/0] 00000052 00000000 c1b97ba0 00000214 00000001 c1b4df58 c1570eac c1b97ba0
[ 5.106083] C0 [ swapper/0] 2c6a5311 c1b4df7c c157153a c1b97ba0 fffffff8 00000007 f0bf325c c1b4c000
[ 5.106128] C0 [ swapper/0] Call Trace:
[ 5.106149] C0 [ swapper/0] [<c1570eac>] cpuidle_enter+0xc/0x10
[ 5.106171] C0 [ swapper/0] [<c157153a>] cpuidle_wrap_enter+0x2a/0xa0
[ 5.106193] C0 [ swapper/0] [<c15715c2>] cpuidle_enter_tk+0x12/0x20
[ 5.106215] C0 [ swapper/0] [<c1570ea0>] ? cpufreq_get_measured_perf+0xe0/0xe0
[ 5.106237] C0 [ swapper/0] [<c1571202>] cpuidle_idle_call+0x92/0x2e0
[ 5.106259] C0 [ swapper/0] [<c106c08b>] ? atomic_notifier_call_chain+0x3b/0x50
[ 5.106281] C0 [ swapper/0] [<c100ee94>] cpu_idle+0x94/0xe0
[ 5.106304] C0 [ swapper/0] [<c1812d80>] rest_init+0x6c/0x7c
[ 5.106327] C0 [ swapper/0] [<c1bef743>] start_kernel+0x2e5/0x2ea
[ 5.106349] C0 [ swapper/0] [<c1bef0b1>] i386_start_kernel+0xb1/0xb9
[ 5.106364] C0 [ swapper/0] Code: 00 00 89 e3 31 d2 81 e3 00 e0 ff ff 89 d1 8d 43 08 0f 01 c8 0f ae f0 89 f6 8b 43 08 a8 08 75 0b b9 01 00 00 00 8b 45 e4 0f 01 c9 <8b> 4d e8 85 c9 0f 85 c1 01 00 00 83 7d e4 52 0f 85 47 03 00 00
[ 5.106605] C0 [ swapper/0] Call Trace:
[ 5.106625] C0 [ swapper/0] [<c1570eac>] cpuidle_enter+0xc/0x10
[ 5.106646] C0 [ swapper/0] [<c157153a>] cpuidle_wrap_enter+0x2a/0xa0
[ 5.106668] C0 [ swapper/0] [<c15715c2>] cpuidle_enter_tk+0x12/0x20
[ 5.106690] C0 [ swapper/0] [<c1570ea0>] ? cpufreq_get_measured_perf+0xe0/0xe0
[ 5.106712] C0 [ swapper/0] [<c1571202>] cpuidle_idle_call+0x92/0x2e0
[ 5.106734] C0 [ swapper/0] [<c106c08b>] ? atomic_notifier_call_chain+0x3b/0x50
[ 5.106755] C0 [ swapper/0] [<c100ee94>] cpu_idle+0x94/0xe0
[ 5.106777] C0 [ swapper/0] [<c1812d80>] rest_init+0x6c/0x7c
[ 5.106798] C0 [ swapper/0] [<c1bef743>] start_kernel+0x2e5/0x2ea
[ 5.106819] C0 [ swapper/0] [<c1bef0b1>] i386_start_kernel+0xb1/0xb9
[ 5.107510] C2 [ swapper/0] Request SCU panic dump
[ 5.108522] C2 [ swapper/0] SCU trace on Kernel panic:
[ 5.108536] C2 [ swapper/0] EW0:0x53435554 EW1:0x25210301 TUCS....
[ 5.108549] C2 [ swapper/0] EW2:0x00077810 EW3:0x00000000 .x......
[ 5.108561] C2 [ swapper/0] EW4:0x00000000 EW5:0x00000000 ........
[ 5.108574] C2 [ swapper/0] EW6:0x00000084 EW7:0x01000000 ........
[ 5.108587] C2 [ swapper/0] EW8:0x00000000 EW9:0x00000000 ........
[ 5.108600] C2 [ swapper/0] EW10:0x00000100 EW11:0x08000000 ........
[ 5.108612] C2 [ swapper/0] EW12:0x00000000 EW13:0x08000000 ........
[ 5.108626] C2 [ swapper/0] EW14:0x80000000 EW15:0x00000000 ........
[ 5.108638] C2 [ swapper/0] EW16:0x00000000 EW17:0x00076c66 ....fl..
[ 5.108652] C2 [ swapper/0] EW18:0x00076583 EW19:0x000765c3 .e...e..
[ 5.108665] C2 [ swapper/0] EW20:0x150c150c EW21:0x00000000 ........
[ 5.108678] C2 [ swapper/0] EW22:0x00000000 EW23:0x00000000 ........
[ 5.108691] C2 [ swapper/0] EW24:0x00076c60 EW25:0x00000013 .l......
[ 5.108704] C2 [ swapper/0] EW26:0xc0000000 EW27:0x00000000 ........
[ 5.108716] C2 [ swapper/0] EW28:0x00000000 EW29:0x00000000 ........
[ 5.108729] C2 [ swapper/0] EW30:0x00000000 EW31:0x00000000 ........
[ 5.108742] C2 [ swapper/0] EW32:0x00000000 EW33:0x00000000 ........
[ 5.108755] C2 [ swapper/0] EW34:0x00000000 EW35:0x00000000 ........
[ 5.108767] C2 [ swapper/0] EW36:0x00000000 EW37:0x00000000 ........
[ 5.108781] C2 [ swapper/0] EW38:0x00000000 EW39:0x00000000 ........
[ 5.108793] C2 [ swapper/0] EW40:0x00000000 EW41:0x00000000 ........
[ 5.108806] C2 [ swapper/0] EW42:0x00000000 EW43:0x00000000 ........
[ 5.108819] C2 [ swapper/0] EW44:0x00000000 EW45:0x00000000 ........
[ 5.108832] C2 [ swapper/0] EW46:0x00000000 EW47:0x00000000 ........
[ 5.108844] C2 [ swapper/0] EW48:0x00000000 EW49:0x00000000 ........
[ 5.108857] C2 [ swapper/0] EW50:0x00000000 EW51:0x00000000 ........
[ 5.108870] C2 [ swapper/0] EW52:0x00000000 EW53:0x00000000 ........
[ 5.108883] C2 [ swapper/0] EW54:0x00000000 EW55:0x00000000 ........
[ 5.108896] C2 [ swapper/0] EW56:0x00000000 EW57:0x00000000 ........
[ 5.108909] C2 [ swapper/0] EW58:0x00000000 EW59:0x00000000 ........
[ 5.108921] C2 [ swapper/0] EW60:0x00000000 EW61:0x00000000 ........
[ 5.108934] C2 [ swapper/0] EW62:0x00000000 EW63:0x00000000 ........
[ 5.108947] C2 [ swapper/0] EW64:0x00000000 EW65:0x00000000 ........
[ 5.108960] C2 [ swapper/0] EW66:0x00000000 EW67:0x00000000 ........
[ 5.108972] C2 [ swapper/0] EW68:0x00000000 EW69:0x00000000 ........
[ 5.108985] C2 [ swapper/0] EW70:0x00000000 EW71:0x00000000 ........
[ 5.108998] C2 [ swapper/0] EW72:0x00000000 EW73:0x00000000 ........
[ 5.109011] C2 [ swapper/0] EW74:0x00000000 EW75:0x00000000 ........
[ 5.109024] C2 [ swapper/0] EW76:0x00000000 EW77:0x00000000 ........
[ 5.109037] C2 [ swapper/0] EW78:0x00000000 EW79:0x00000000 ........
[ 5.109049] C2 [ swapper/0] EW80:0x00000000 EW81:0x00000000 ........
[ 5.109062] C2 [ swapper/0] EW82:0x00000000 EW83:0x00000000 ........
[ 5.109075] C2 [ swapper/0] EW84:0x00000000 EW85:0x00000000 ........
[ 5.109088] C2 [ swapper/0] EW86:0x00000000 EW87:0x00000000 ........
[ 5.109100] C2 [ swapper/0] EW88:0x00000000 EW89:0x00000000 ........
[ 5.109114] C2 [ swapper/0] EW90:0x00000000 EW91:0x00000000 ........
[ 5.109126] C2 [ swapper/0] EW92:0x00000000 EW93:0x00000000 ........
[ 5.109139] C2 [ swapper/0] EW94:0x00000000 EW95:0x00000000 ........
[ 5.109152] C2 [ swapper/0] EW96:0x00000000 EW97:0x00000000 ........
[ 5.109165] C2 [ swapper/0] EW98:0x00000000 EW99:0x00000000 ........
[ 5.109178] C2 [ swapper/0] EW100:0x00000000 EW101:0x00000000 ........
[ 5.109191] C2 [ swapper/0] EW102:0x00000000 EW103:0x00000000 ........
[ 5.109204] C2 [ swapper/0] EW104:0x00000000 EW105:0x00000000 ........
[ 5.109217] C2 [ swapper/0] EW106:0x00000000 EW107:0x00000000 ........
[ 5.109231] C2 [ swapper/0] EW108:0x00000000 EW109:0x00000000 ........
[ 5.109244] C2 [ swapper/0] EW110:0x00000000 EW111:0x00000000 ........
[ 5.109257] C2 [ swapper/0] EW112:0x00000000 EW113:0x00000000 ........
[ 5.109270] C2 [ swapper/0] EW114:0x00000000 EW115:0x00000000 ........
[ 5.109283] C2 [ swapper/0] EW116:0x00000000 EW117:0x00000000 ........
[ 5.109297] C2 [ swapper/0] EW118:0x00000000 EW119:0x00000000 ........
[ 5.109310] C2 [ swapper/0] EW120:0x00000000 EW121:0x00000000 ........
[ 5.109323] C2 [ swapper/0] EW122:0x00000000 EW123:0x00000000 ........
[ 5.109336] C2 [ swapper/0] EW124:0x00000000 EW125:0x00000000 ........
[ 5.109350] C2 [ swapper/0] EW126:0x00000000 EW127:0x00000000 ........
[ 5.109363] C2 [ swapper/0] EW128:0x00000000 EW129:0x00400040 ........
[ 5.109377] C2 [ swapper/0] EW130:0x434d4d65 EW131:0x4c4c4420 eMMC.DLL
[ 5.109391] C2 [ swapper/0] EW132:0x636f4c20 EW133:0x2064656b .Locked.
[ 5.109404] C2 [ swapper/0] EW134:0x203b6e69 EW135:0x74696157 in..Wait
[ 5.109418] C2 [ swapper/0] EW136:0x756f6320 EW137:0x7520746e .count.u
[ 5.109432] C2 [ swapper/0] EW138:0x4c442c73 EW139:0x6f4c204c s.DLL.Lo
[ 5.109445] C2 [ swapper/0] EW140:0x78302063 EW141:0x30303030 c.0x0000
[ 5.109459] C2 [ swapper/0] EW142:0x31303030 EW143:0x30783020 0001.0x0
[ 5.109472] C2 [ swapper/0] EW144:0x30303030 EW145:0x00303030 0000000.
[ 5.109486] C2 [ swapper/0] EW146:0x00000000 EW147:0x00000000 ........
[ 5.109499] C2 [ swapper/0] EW148:0x00000000 EW149:0x00000000 ........
[ 5.109512] C2 [ swapper/0] EW150:0x00000000 EW151:0x00000000 ........
[ 5.109525] C2 [ swapper/0] EW152:0x00000000 EW153:0x00000000 ........
[ 5.109538] C2 [ swapper/0] EW154:0x00000000 EW155:0x00000000 ........
[ 5.109552] C2 [ swapper/0] EW156:0x00000000 EW157:0x00000000 ........
[ 5.109565] C2 [ swapper/0] EW158:0x00000000 EW159:0x00000000 ........
[ 5.109578] C2 [ swapper/0] EW160:0x00000000 EW161:0x00000000 ........
[ 5.109591] C2 [ swapper/0] EW162:0x00000000 EW163:0x00000000 ........
[ 5.109604] C2 [ swapper/0] EW164:0x00000000 EW165:0x00000000 ........
[ 5.109618] C2 [ swapper/0] EW166:0x00000000 EW167:0x00000000 ........
[ 5.109631] C2 [ swapper/0] EW168:0x00000000 EW169:0x00000000 ........
[ 5.109644] C2 [ swapper/0] EW170:0x00000000 EW171:0x00000000 ........
[ 5.109657] C2 [ swapper/0] EW172:0x00000000 EW173:0x00000000 ........
[ 5.109671] C2 [ swapper/0] EW174:0x00000000 EW175:0x00000000 ........
[ 5.109684] C2 [ swapper/0] EW176:0x00000000 EW177:0x00000000 ........
[ 5.109697] C2 [ swapper/0] EW178:0x00000000 EW179:0x00000000 ........
[ 5.109710] C2 [ swapper/0] EW180:0x00000000 EW181:0x00000000 ........
[ 5.109723] C2 [ swapper/0] EW182:0x00000000 EW183:0x00000000 ........
[ 5.109736] C2 [ swapper/0] EW184:0x00000000 EW185:0x00000000 ........
[ 5.109750] C2 [ swapper/0] EW186:0x00000000 EW187:0x00000000 ........
[ 5.109763] C2 [ swapper/0] EW188:0x00000000 EW189:0x00000000 ........
[ 5.109776] C2 [ swapper/0] EW190:0x00000000 EW191:0x00000000 ........
[ 5.109789] C2 [ swapper/0] EW192:0x00000000 EW193:0x00000000 ........
[ 5.109802] C2 [ swapper/0] EW194:0x00000000 EW195:0x00000000 ........
[ 5.109816] C2 [ swapper/0] EW196:0x00000000 EW197:0x00000000 ........
[ 5.109829] C2 [ swapper/0] EW198:0x000000ff EW199:0x00000000 ........
[ 5.109841] C2 [ swapper/0] EW200:0xaaaa5555 UU..
[ 5.109852] C2 [ swapper/0] intel_scu_ipc_emergency_write_oemnib: POEMNIB remap poemnibw 0xffff3440 size 64
[ 5.109936] C2 [ swapper/0] intel_scu_ipc_emergency_write_oemnib: POEMNIB remap poemnibw 0xffff3440 size 64
[ 5.196121] C2 [ swapper/0] (sec_debug_panic_handler) checksum_sched_log: 0
[ 5.196133] C2 [ swapper/0] (sec_debug_hw_reset) Kernel Build Info : Date:Mar 8 2021 Time:16:56:02
Spoiler: Log from UART
Code:
IA32 CPU Firmware
Copyright (C) 1999-2013, Intel Corporation. All rights reserved.
------------------------------>FOR Teewinot ONLY<-----------------------------
******************************************************************************
************** Customer release based on Rel 00.49 + TWN changes**************
**************** BZ=115220 Bypass time/date check for product ****************
****************** BZ=118523 Cold Reset on ExecuteOS failure *****************
****** BZ=124478[TW 346-500-676] Request for logging enhancement in IAFW *****
************* BZ=127192 Disable Active Refresh during JEDEC Init *************
******************* BZ=none include ucode patch M013065110E ******************
**************************** New in this code drop ***************************
***** BZ=none Changed trace to match TWN RAMDUMP application requirement *****
*************** BZ=none Removed UART and PTI HW output methods ***************
******** Short circuiting the emInit when a fixed battery is detected. *******
********************* Customization done 201308261512 MST ********************
******************************************************************************
******************************INTEL CONFIDENTIAL******************************
0x1E, 0x20, 0x21,
ERROR:::::SPID Not Programmed, Fake data being used based on IFWI version
ERROR:::::SPID FRU Not Programmed, Fake data being used based on IFWI version
OSC_CLK3 defaults only
0x22,
OEM board; Skip spidBasedPanelNdxUpdate
0x23,
Forced Battery via SMIP FPO Bit 2
0x28, 0x2A, 0x2B, in csSFIDevsEntries, HW Id 0x0019
SFI Dev...PR3
in csSFIGpioEntries, HW Id 0x0019
SFIOEMBInit:tbl->spidTbl update
0x2C, 0x2D, 0x2F PostCodes Done
IA32 FW: CPU v000.073/00.49; SUPP v000.073/00.49; VH: 000.081/00.51
IA Timestamp: 2013.08.26:18.00 (INTELFDK)
SCU FW: ROM 177.000/B1.00; RT 033.048/21.30
PUNIT FW: v224.064/E0.40
IFWI: v249.086/F9.56
PL: 0000010E
Config & PCB: OEM Platform, C, CLV+ B1, Micron (00,00) SR 4Gb 1067 1GB
FHOB DW0/DW1: 00000104:00010140
I2C Expander: FFFFFFFC:0000000F
IA Options: 024020A1:00000000:03E00000:80005C00:00000101;0558
[OS HASH VERIFY] [EIST] [eMMC] [VALID BATT][WDT]
Loading OS...
pOsip = 1000000
-->OSIP verified
FA050000 FA050000
FA050000 FA050000
Boot path override selected OS image 0 (OS Attribute 0x00, Reboot Reason 0x00)
FA050000 FA050000
Splash disabled in GCT
Splash display time: 2 ms
-->Bootable OS image 0 found for requested type 0 (OSII attribute 0x00)
-->Loading OS image 0 from eMMC block 0x00000032 to DRAM address 0x010FFE20
-->Starting transfer of 0xA11 512-byte blocks to DRAM
-->Done loading OS Image to DRAM
-->platformConfigBuffer_pt.scuFhobDw0.osven != 0
-->osIndex: 0, Signed Image
OS image 0 PASSED verify
Booting MOS
*********************************
Starting command line:
-init=/init pci=noearly console=ttyMFD2 console=ttyS0 console=logk0 earlyprintk=nologger loglevel=8 hsu_dma=7 kmemleak=off ptrace.ptrace_can_access=1 androidboot.bootmedia=sdcard androidboot.hardware=ctp_pr1 emmc_ipanic.ipanic_part_number=1 ip=50.0.0.2:50.0.0.1::255.255.255.0::usb0:on hsu_rx_wa g_android.fastboot=1 droidboot.scratch=100
-
OSNIB.wakesrc = 0x5
OSNIB.RR = 0x0
Battery is high enough for normal boot
3767mV > 0mV
Ending command line:
-init=/init pci=noearly console=ttyMFD2 console=ttyS0 console=logk0 earlyprintk=nologger loglevel=8 hsu_dma=7 kmemleak=off ptrace.ptrace_can_access=1 androidboot.bootmedia=sdcard androidboot.hardware=ctp_pr1 emmc_ipanic.ipanic_part_number=1 ip=50.0.0.2:50.0.0.1::255.255.255.0::usb0:on hsu_rx_wa g_android.fastboot=1 droidboot.scratch=100 androidboot.wakesrc=05 androidboot.mode=main-
*********************************
WDT aka Timer7 setup
Warn Duration for Timer7: 00 seconds
Start Timer7 bit 0 -> 1: 00000000000000000000000000000000
Calling OS entry point --> 0x01101000 ...
Using NEW OSHOB structure size = 176 bytes
OSNIB size = 32 bytes OEMNIB size = 64 bytes
0xFF00_0510 FullChipRegister: Status flag = 0x0
0xFF10_0510 SCFabricRegister: Status flag = 0x0
RTCSC2 = 0x11, RTCSC3 = 0xcf, RTCSC4 = 0xcf
Watchdog Disabled!
__stmpe811_write : fail
MUIC: CONTROL1:0x1b
MUIC: CONTROL1:0x1b
MUIC: CONTROL2:0x3e
MUIC: CONTROL2:0x3e
[SCU_IPC_DEBUG] board ID: NOT_IDENTIFIED(8)
VERSION : 0xa501
mmc_read_ext_csd : ext_csd_rev = 0x5
cardtype: 0x00000007
SB_MMC_HS_52MHZ_1_8V_3V_IO
mmc->card_caps: 0x00000311
mmc->host_caps: 0x00000311
!!!Enter 8 Bit mode.!!!
clt_mmc_init: mmc->capacity = 0x1d58000
[BOOT] RESETIRQ1=0x00 RESETIRQ2=0x00 (interrupt tree)
[BOOT] SCU_TR=0x00020003 IA_TR=0xffffffff (oshob)
[BOOT] RR=0x00 WD=0x00 ALARM=0x00 (osnib)
[BOOT] WAKESRC=0x05 RESETIRQ1=0x01 RESETIRQ2=0x00 (osnib)
Samsung S-Boot 4.0 for GT-P5200 (Aug 27 2014 - 18:02:10)
CLT(EVT 0.0) / 1024MB / 15024MB / Rev 8 / P5200XXxxxxx
pit_check_signature (PIT) valid.
initialize_ddi_data: usable! (24:0xf)
PARAM ENV VERSION: v1.0..
pressed_key = 0x0
clt_charger_init : [battery] using external charger init(3)
STATUS1:0x3d, 2:0x40
vbvolt=0x1, chgtyp=0x0, adc=0x1d, ret=0x1001d
[check_cable_type] : Output of USB Charger Detection 0
[max77693_init_charger] : attached device(0x00) : Battery
clt_max77693_set_charger_state: chg_cnfg_02 (0x9f) -> (0x1f) -> (0x1f)
clt_max77693_set_charger_state: chg_cnfg_03 (0x20) -> (0x00) -> (0x00)
clt_max77693_set_charger_state: chg_cnfg_04 (0xdd) -> (0xdd) -> (0xdd)
clt_max77693_set_charger_state: chg_cnfg_09 (0x19) -> (0x05) -> (0x05)
set_charger_state : buck(1), chg(0), reg(0x04)
init_fuel_gauge: Start!!
[0] get_adc_battid() = 68
[1] get_adc_battid() = 68
[2] get_adc_battid() = 69
get_adc_battid() = 68
init_fuel_gauge: Battery type : SDI
init_fuel_gauge: NOT initialized (0x32cc)
do_soft_por: Lock Done
do_soft_por - Status (0x00 = 0x0002)
do_soft_por - SoftPOR Done
Initialization_routine: Start!!
[MAX17050 Model data] : 0xab80 0xb730 0xb980 0xbb00 0xbc00 0xbd00 0xbe30 0xbfa0 0xc0f0 0xc240 0xc4d0 0xc720 0xcc20 0xcf30 0xd230 0xd630 0x1c0 0x1300 0xd90 0x1640 0x1e60 0x18d0 0x15f0 0xff0 0xff0 0x7e0 0xb30 0x7c0 0x7d0 0x8f0 0x5d0 0x5d0 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180
Initialization_routine: QResidual20 (0x1404)
Initialization_routine: QResidual30 (0x1004)
get_CGAIN: CGain = 0x3645
Initialization_routine: Finished!! (SDI type)
STATUS1:0x3d, 2:0x40
vbvolt=0x1, chgtyp=0x0, adc=0x1d, ret=0x1001d
Initialization_routine: Start!!
[MAX17050 Model data] : 0xab80 0xb730 0xb980 0xbb00 0xbc00 0xbd00 0xbe30 0xbfa0 0xc0f0 0xc240 0xc4d0 0xc720 0xcc20 0xcf30 0xd230 0xd630 0x1c0 0x1300 0xd90 0x1640 0x1e60 0x18d0 0x15f0 0xff0 0xff0 0x7e0 0xb30 0x7c0 0x7d0 0x8f0 0x5d0 0x5d0 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180 0x180
Initialization_routine: QResidual20 (0x1404)
Initialization_routine: QResidual30 (0x1004)
get_CGAIN: CGain = 0x3645
Initialization_routine: Finished!! (SDI type)
init_fuel_gauge: re-write val(0x0077) at LearnCFG_REG
clt_charger_init : cable_type(0x00)
intel_scu_ipc_cmd_oemnib : done => 0x12345670
check_reboot_cmd: nCmd = 12345670 ... setting REBOOT_MODE to 0
clear_reboot_mode
intel_scu_ipc_cmd_oemnib : done => 0x0
debug level = 0x4f4c
disable max77693 manual reset
clt_max77693_disable_manual_reset: set max77693 MANCTRL1 val = 0x4
clt_max77693_disable_manual_reset: read max77693 MANCTRL1 val = 0x4
disable PMIC cod off triggered by PWRBTN#: 6
intel_scu_ipc_cmd_oemnib : done => 0xffffffff
check_download: 0
Is_lpm_boot : boot-mode saved in param = 0
Is_lpm_boot : jig-on level = 0, ignore...
STATUS1:0x3d, 2:0x40
vbvolt=0x1, chgtyp=0x0, adc=0x1d, ret=0x1001d
stat=0x1001d, adc=0x1d, chg=0x0, vbvolt=1, pinLevel=0
Is_lpm_boot : charger is not detected
fuel_gauge_read_vcell: VCELL(3846), data(0xc054)
fuel_gauge_read_soc: SOC(56), data(0x38ad)
check_low_battery : rb=0 jig=0
check_low_battery : v=3846 soc=56
scr_draw_image: draw 'logo.jpg'...
read 'logo.jpg'(105420) completed.
If there's someone who is willing to help me improve postmarketOS on this tablet, feel free to contact me:
(Matrix) @ungeskriptet:matrix.org

Finally got it to work. This commit should fix it.
Wiki page
I used this kernel instead: https://github.com/dpdudek/android_kernel_samsung_santos10

so can we now install linux? the device is still in "not booting" category on pmos website.

You might be looking at the 3G version. The Wi-Fi port also works on the 3G variant (and LTE maybe?) but it really isn't usable with X11 right now although wayland seems to work somewhat fine without HW acceleration. I could only find GPU drivers for ARM for this tablet since it is x86 and has a PowerVR GPU.

great, 3g version is what i have. and i dodnt noticed when wiki page mooved to "boot successful" category, sorry.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
but my question is when i am executing the instruction of installation via pmbootstrap i'm being asked for device codename, neither santos103g not p5200 there, but santos10wifi. so if i have 3g version, should i use santos10wifi or what? sorry my bad english and stupid questions
oh sorry ive didnt notice that sign on santos103g wiki page saying the installation is the same

Select the Wi-Fi version. The 3G version uses the same kernel and the only thing that won't work is 3G.
I recommend you to use Weston if possible, as it is the best working graphical environment. Gnome also uses Wayland so it should be also good, but currently it won't start (haven't figured it out yet).

great, thanks very much for your work. btw what user interfaces can i have working? you said wayland so i've tried plasma-bigscreen and stuck at "Loading..." however weston wokrs well.

Your only option is Weston for a usable interface at the moment and AFAIK plasma-bigscreen is for TVs.

hi ,
i'm sorry but i did not understand how to install in my TAB 3 wifi
can some one share the install process because realy intersting about this project.

First you need to have Linux installed on your PC/in a VM (if you use a VM, you need to setup USB forwarding), I recommend you installing Manjaro XFCE.
Once you are booted into Linux, follow these steps:
Spoiler: Instructions to install pmbootstrap from pip (any Linux distro)
1. Install pip from your package manager:
For Arch Linux (and Manjaro): sudo pacman -S python-pip
For Debian (and Ubuntu, Linux Mint, Pop OS): sudo apt-get install python3-pip
2. Install pmbootstrap with pip:
pip install --user pmbootstrap && source ~/.profile
Spoiler: Instuctions to install pmbootstrap from the AUR (Arch Linux and Arch-based distros only)
1. Option: Install using an AUR helper
Code:
git clone https://aur.archlinux.org/paru-bin
cd paru-bin
makepkg -si
paru -S pmbootstrap
2. Option: Install with Pamac (GUI method, preinstalled on Manjaro)
Launch Pamac → 3 Dots → Preferences → Third Party → Turn on "Enable AUR support", "Check for updates" and "Check for development packages updates"
Search for pmbootstrap and install it.
Spoiler: Instructions to install postmarketOS
Launch a terminal and initialize pmbootstrap:
Code:
pmbootstrap init
# Work path: ~/.pmbootstrap
# Channel: edge
# Vendor: samsung
# Device codename: santos10wifi (choose this even if you have a 3G or LTE tablet)
# Enable Wi-Fi firmware
# Username: santos (choose a name you like)
# User interface: weston (currently only weston is the most usable UI, X11-based UIs are very laggy)
# Don't change additional options
# Extra packages: vim,htop,onboard (recommended, but optional)
# Enable your timezone
# Choose your default locale (en_US.UTF-8 for American English)
# Device hostname: santos10wifi (choose a hostname you like)
# Copy public SSH keys (recommended if you have generated a pair but optional)
# Build outdated packages during 'pmbootstrap install': y
Generate the images:
Code:
pmbootstrap install
# Set a password
Flash the kernel and rootfs to the tablet (backup your data before):
Code:
# Put the device into download mode: Power & Vol -
# This should be fast so be ready to put the device into download mode again after it reboots
pmbootstrap flasher flash_kernel
# Flashing the rootfs might take a while
pmbootstrap flasher flash_rootfs
Spoiler: Connecting to a Wi-Fi network
Connect the tablet to a PC (it should create a new network interface):
Code:
ssh [email protected]
# change santos to your username, if you changed it and type yes if asked
sudo nmtui
# A blue menu will appear
In nmtui:
Activate a connection → Select your network → Type your Wi-Fi password → Quit nmtui
When connected, unplug the cable.
After you followed these steps your tablet is running pmOS with a Wi-Fi connection.

thanks friend will try now

i get this errors in log file when generating the image :
/home/wintosh/.pmbootstrap/chroot_rootfs_samsung-santos10wifi --cache-dir /home/wintosh/.pmbootstrap/cache_apk_x86 --initdb --arch x86 add alpine-base
EDIT:
i was it using Windows subsystem for Linux (WSL) and it's not compatible

@Ungeskriptet many thanks for your efforts.

@kls0e I'll try mainlining the device (after I mainlined GT-I9100G or not) with this kernel. This could fix many problems like X11

great. I will be happy to test and update the documentation.

Ungeskriptet said:
# Put the device into download mode: Power & Vol -
# This should be fast so be ready to put the device into download mode again after it reboots
pmbootstrap flasher flash_kernel
Click to expand...
Click to collapse
- I am assuming that the device is connected to the Linux (Fedora in my case) computer via USB:
I get:
Code:
$ pmbootstrap flasher flash_kernel
[sudo] password for phr:
[19:41:24] (rootfs_samsung-santos10wifi) mkinitfs samsung-santos10wifi
[19:41:28] (native) flash kernel samsung-santos10wifi
[19:41:29] (native) install heimdall avbtool
< wait for any device >
- and nothing else happens on the computer or the tablet . . I was expecting that pbmbootstrap would find the USB-connected tablet and do the flashing . .
BTW, I have not installed TWRP - the native download mode should be OK?
Thanks,
Phil.

philip_rhoades said:
- I am assuming that the device is connected to the Linux (Fedora in my case) computer via USB:
I get:
Code:
$ pmbootstrap flasher flash_kernel
[sudo] password for phr:
[19:41:24] (rootfs_samsung-santos10wifi) mkinitfs samsung-santos10wifi
[19:41:28] (native) flash kernel samsung-santos10wifi
[19:41:29] (native) install heimdall avbtool
< wait for any device >
- and nothing else happens on the computer or the tablet . . I was expecting that pbmbootstrap would find the USB-connected tablet and do the flashing . .
BTW, I have not installed TWRP - the native download mode should be OK?
Thanks,
Phil.
Click to expand...
Click to collapse
Hmm. Seems like your tablet isn't being recognized by pmbootstrap.
Does your tablet show up in lsusb or dmesg on your PC when connected via USB?
TWRP isn't neccessary for postmarketOS unless you flash it via a recovery ZIP, so thats not the issue.

Ungeskriptet said:
Hmm. Seems like your tablet isn't being recognized by pmbootstrap.
Does your tablet show up in lsusb or dmesg on your PC when connected via USB?
TWRP isn't neccessary for postmarketOS unless you flash it via a recovery ZIP, so thats not the issue.
Click to expand...
Click to collapse
Ah! - there were two problems - I had forgotten to turn on USB debugging and secondly I had some dodgy USB cables - lucky #3 worked!
OK, so the tablet booted up happily with pmOS ! I played around with the tk stuff for a while and was able to start Wayland terminals, and the screen looks very nice - but I can't do much with it because I can't get access to anything else and no visual keyboard pops up . .
Also, although it still showing up on my LAN as 192.168.1.105, I can't even ping it, let alone ssh to it . . but still - some progress! I am happy that I have made it this far but is there more that can be done with the tablet now?
I should write out my variations on using Fedora and clarifying some steps too . .
Thanks!

hey people, i recently tried setting up postmarketOS on Samsung Galaxy Tab 3 10.1 and i am facing the same problem as philip, but changing the usb cables and trying to flash from other computers (other linux mint, and ubuntu) did not help.
i am new to this and just started with postmarketOS trying to use the old samsung device without google stuffs...
tldr: use "Power + Volume Down"!
Spoiler: this is what happens when you press "Power + Volume Up" instead...
usb debugging is activated and pmbootstrap installed/prepared as described above by Ungeskriptet.
(Edit: I wasnt following the guide accordingly, i pressed "Power + Vol Up" instead of "Power + Vol Down"....)
i am using Linux Mint 20.2 Cinnamon btw.
when doing "pmbootstrap init" multiple times (to make sure everything is set up fresh) i am also asked for "Zap existing chroots to apply configuration? (y/n) [y]: _ "
-- is it fine to just "y" there?
so moving on to flashing i am receiving same as philip:
Spoiler: wait for any device - problem
Code:
$ pmbootstrap flasher flash_kernel
[16:45:32] WARNING: package postmarketos-mkinitfs: aport version 1.1.2-r4 is lower than 1.2-r0 from the binary repository. 1.2-r0 will be used when installing postmarketos-mkinitfs. See also: <https://postmarketos.org/warning-repo2>
[16:45:32] (rootfs_samsung-santos10wifi) mkinitfs samsung-santos10wifi
[16:45:32] (native) flash kernel samsung-santos10wifi
< wait for any device >
however "lsusb" doesnt show any Samsung device
but "dmesg" displays a lot including:
Spoiler: dmesg output
Code:
[17027.280526] usb 1-4: USB disconnect, device number 9
[17027.701836] usb 1-4: new high-speed USB device number 10 using xhci_hcd
[17027.939869] usb 1-4: New USB device found, idVendor=04e8, idProduct=6860, bcdDevice= 4.00
[17027.939872] usb 1-4: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[17027.939873] usb 1-4: Product: GT-P5210
[17027.939874] usb 1-4: Manufacturer: samsung
[17027.939875] usb 1-4: SerialNumber: 3200574e03bfc000
[17027.982910] cdc_acm 1-4:1.1: ttyACM0: USB ACM device
[17094.836586] usb 1-4: USB disconnect, device number 10
-- the same without the line "USB disconnect, device number 10" does appear when starting the tablet in original android - so i would say, the usb cable is working
deviceinfo
from the wiki i already tried setting the deviceinfo "deviceinfo_flash_fastboot_vendor_id="04e8" "
in "~/.pmbootstrap/cache_git/pmaports/device/testing/device-samsung-santos10wifi/deviceinfo"
-- but i am still "waiting for any device"
and the wiki of deviceinfo states as obsolete options:
flash_fastboot_vendor_id: fastboot used to have a -i option, but this was removed (#1830). Since we only had one device using this and nobody to verify if the option is really needed with this device, we decided to remove it. If you are interested in bringing it back, please create a new issue.
Click to expand...
Click to collapse
udev
the fix "Maybe you need to install udev rules on your host Linux distribution" (also from wiki), i do not really understand how to start with ..could you give me a hint? browsing resulted in finding this https://community.linuxmint.com/software/view/udev - Version 245.4-4ubuntu3.14 of this was already installed
last solution from wiki with "pmbootstrap shutdown" did not help either
but some different output at dmesg was produced (dont know it it really was because of pmb shutdown):
Spoiler: dmesg output (a little different than earlier)
Code:
[18287.548108] usb 1-4: new high-speed USB device number 14 using xhci_hcd
[18287.786734] usb 1-4: New USB device found, idVendor=04e8, idProduct=6860, bcdDevice= 4.00
[18287.786737] usb 1-4: New USB device strings: Mfr=2, Product=3, SerialNumber=4
[18287.786738] usb 1-4: Product: GT-P5210
[18287.786739] usb 1-4: Manufacturer: samsung
[18287.786740] usb 1-4: SerialNumber: 3200574e03bfc000
[18287.830790] cdc_acm 1-4:1.1: ttyACM0: USB ACM device
[18293.078518] usb 1-4: reset high-speed USB device number 14 using xhci_hcd
[18293.243338] cdc_acm 1-4:1.1: ttyACM0: USB ACM device
[18366.042217] usb 1-4: reset high-speed USB device number 14 using xhci_hcd
[18366.207183] cdc_acm 1-4:1.1: ttyACM0: USB ACM device
[18408.865985] [UFW BLOCK] IN=enp6s0 OUT= MAC=01:00:5e:00:00:01:88:9e:68:cd:5b:0c:08:00 SRC=192.168.0.1 DST=224.0.0.1 LEN=28 TOS=0x00 PREC=0x00 TTL=1 ID=0 PROTO=2
[18408.866158] [UFW BLOCK] IN=enp6s0 OUT= MAC=01:00:5e:00:00:01:88:9e:68:cd:5b:0c:08:00 SRC=192.168.0.1 DST=224.0.0.1 LEN=32 TOS=0x00 PREC=0x00 TTL=1 ID=0 PROTO=2
// -- and 10 more times the same "[UFW BLOCK] ..." line inbetween --
[19094.131416] usb 1-4: USB disconnect, device number 14
when starting the tablet with power+vol [*edit: Vol Up] i am seeing "Android system recovery <3e>" quit fast ..is this where i need to start the "pmbootstrap flasher flash_kernel"? (i also tried starting the flasher and waiting for the device when booting using power+vol.. ending up with the same result)
Spoiler: device displays this when fastbooting(?)
Code:
Android system recovery <3e>
KOT49H.P5210XXUB0H1
Volume up/down to move hightlight:
power button to select.
> reboot system now
> apply update from ADB
> apply update from external storage
> wipe data/factory reset
> wipe cache partition
> apply update from cache
# MANUAL MODE
-- Applying Multi-CSC...
Applied the CSC-code: DBT
Successfully applied multi-CSC.
and in the background i can see "Kein Befehl" + the green Android thing with a warning in its open "stomach"
additionally the battery (the original already "gave up" and was replaced earlier) shows a sign for two days now displaying a red cross in the battery icon, and it has not been loading since then, just reducing its capacity to 35% at the moment ..so time is kind of running out soon :x -- it was loading fine when not activated and running android.
__________
do you have any idea what i am doing wrong?
thanks for your help!
ps: sorry for the long post, i just wanted to give you all information needed..
"Power + Volume Down" = flash mode <- this is what we want.
("Power + Volume Up" = recovery mode)

My fault.
myusernamemustbeunique said:
usb debugging is activated and pmbootstrap installed/prepared as described above by Ungeskriptet.
[...]
when starting the tablet with power+vol[up] i am seeing "Android system recovery <3e>" quit fast ..is this where i need to start the "pmbootstrap flasher flash_kernel"?
Click to expand...
Click to collapse
Answer: No!
I was just too stupid... I pressed "Power + Volume Up" so I entered the recovery mode..... ._.
(-> So it has not been "prepared as described above" (using "Power + Volume Down") and that was the fault.)
Sorry for the troublemaking.
And thanks a lot for the guide, @Ungeskriptet !
I will now step into installing packages for firefox, visual keyboard, etc. ...
-> Do you have any recommodation for setting up the keyboard?

Question Trying to run protected virtual machine

Hey guys. Recently I've got a Pixel 6 Pro device.
I'm trying to run a virtual machine on my phone with additional security features of Android 13 kernel which is called protected KVM(pKVM).
After following the steps of the documentation, I encountered the errors below.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The kernel I'm running on my Pixel 6 Pro device is the latest Android 13 kernel. The command I ran is:
Code:
/apex/com.android.virt/bin/crosvm run --protected-vm -p 'root=/dev/vda' --rwdisk ${my_disk_image} ${my_kernel_image}
Has anyone solved these errors or launched a protected virtual machine successfully?

I haven't tried yet, but I'm a heavy virtual device user so I would definitely be interested if anyone has any luck.

roirraW edor ehT said:
I haven't tried yet, but I'm a heavy virtual device user so I would definitely be interested if anyone has any luck.
Click to expand...
Click to collapse
Although I haven't run a vm with --protected-vm option so far, I successfully ran a vm by following the steps in the link below.
How to run a Linux VM on Android 13
Android 13 adds a virtualization feature. Here's how to use it to run Linux in a VM.
blog.esper.io
Thanks for replying!

headheadhead said:
Although I haven't run a vm with --protected-vm option so far, I successfully ran a vm by following the steps in the link below.
How to run a Linux VM on Android 13
Android 13 adds a virtualization feature. Here's how to use it to run Linux in a VM.
blog.esper.io
Thanks for replying!
Click to expand...
Click to collapse
You're welcome. Your response reminded me that there was an XDA article on the subject about VMs on the Pixel 6 as well, although it probably won't help with what you're trying to do.
Android 13 DP1 allows Google Pixel 6 to run full-fledged Windows 11 as a VM
The Android 13 DP1 unlocks the full KVM functionality on the Google Pixel 6 and 6 Pro. You can now boot Windows 11 and Linux VMs on these phones.
www.xda-developers.com

Hi, I too followed the instruction, but could not get it to run. Can someone tell me how they built their kernel?

Just to clarify I have built several kernels, and I can get them to run but it won't mount my file system. Can anyone show me how they built their kernel?
I am trying to run a Linux kernel in the VM

rgarcia1000 said:
Just to clarify I have built several kernels, and I can get them to run but it won't mount my file system. Can anyone show me how they built their kernel?
I am trying to run a Linux kernel in the VM
Click to expand...
Click to collapse
I can run a VM with following command.
Code:
/apex/com.android.virt/bin/crosvm run -p 'root=/dev/vda' --rwdisk ${my_disk_image} ${my_kernel_image}
The kernel I built is the linux mainline kernel. The image I used is ubuntu cloud image.

Thanks, I will give it a try.

Hi, Guy's and Ladies,
I am new to this board. I have been trying to make this work for 3 weeks now.
This is what I tried.
Spoiler
./crosvm run --disable-sandbox -p 'init=/bin/sh' --rwroot /data/local/tmp/ubuntu-20.04-server-cloudimg-arm64.squashfs /data/local/tmp/ubuntu-20.04-serv>
[INFO:external/crosvm/src/linux/device_helpers.rs:131] Trying to attach block device: /data/local/tmp/ubuntu-20.04-server-cloudimg-arm64.squashfs
[INFO:external/crosvm/disk/src/disk.rs:175] disk size 379260928,
[INFO:external/crosvm/disk/src/disk.rs:164] Disk image file is hosted on file system type f2f52010
[INFO:external/crosvm/disk/src/disk.rs:175] disk size 379260928,
[INFO:external/crosvm/disk/src/disk.rs:164] Disk image file is hosted on file system type f2f52010
[ERROR:external/crosvm/src/main.rs:2884] crosvm has exited with error: the architecture failed to build the vm: kernel could not be loaded: Reading image into memory failed: invalid guest memory access at addr=0x80800000: requested memory range spans past the end of the region: offset=8388608 count=568590336 region_size=268435456
I also tried:
./crosvm run --disable-sandbox -p 'init=/bin/sh' --rwroot /data/local/tmp/alpine-rootfs.img /data/local/tmp/Image
[INFO:external/crosvm/src/linux/device_helpers.rs:131] Trying to attach block device: /data/local/tmp/alpine-rootfs.img
[INFO:external/crosvm/disk/src/disk.rs:175] disk size 2613248,
[INFO:external/crosvm/disk/src/disk.rs:164] Disk image file is hosted on file system type f2f52010
[INFO:external/crosvm/disk/src/disk.rs:175] disk size 2613248,
[INFO:external/crosvm/disk/src/disk.rs:164] Disk image file is hosted on file system type f2f52010
[ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x411fd440]
[ 0.000000] Linux version 5.16.13-1-aarch64-ARCH ([email protected]) (aarch64-unknown-linux-gnu-gcc (GCC) 11.2.0, GNU ld (GNU Binutils) 2.38) #1 SMP Thu Mar 10 01:59:18 UTC 2022
[ 0.000000] Machine model: linux,dummy-virt
[ 0.000000] efi: UEFI not found.
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000080000000-0x000000008fffffff]
[ 0.000000] DMA32 empty
[ 0.000000] Normal empty
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000080000000-0x000000008fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000008fffffff]
[ 0.000000] cma: Reserved 64 MiB at 0x000000008b800000
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.1 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: Trusted OS migration not required
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] smccc: KVM: hypervisor services detected (0x00000000 0x00000000 0x00000000 0x00000003)
[ 0.000000] percpu: Embedded 20 pages/cpu s44568 r8192 d29160 u81920
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: detected: GIC system register CPU interface
[ 0.000000] CPU features: detected: Hardware dirty bit management
[ 0.000000] CPU features: detected: Spectre-v4
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512
[ 0.000000] Kernel command line: panic=-1 console=ttyS0 init=/bin/sh root=/dev/vda rw
[ 0.000000] Dentry cache hash table entries: 32768 (order: 6, 262144 bytes, linear)
[ 0.000000] Inode-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[ 0.000000] mem auto-init: stackff, heap allocff, heap freeff
[ 0.000000] Memory: 150828K/262144K available (19648K kernel code, 3938K rwdata, 9712K rodata, 6336K init, 865K bss, 45780K reserved, 65536K cma-reserved)
[ 0.000000] random: get_random_u64 called from cache_random_seq_create+0x84/0x184 with crng_init=0
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] rcu: Hierarchical RCU implementation.
[ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=1.
[ 0.000000] Trampoline variant of Tasks RCU enabled.
[ 0.000000] Rude variant of Tasks RCU enabled.
[ 0.000000] Tracing variant of Tasks RCU enabled.
[ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
[ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1
[ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[ 0.000000] GICv3: 32 SPIs implemented
[ 0.000000] GICv3: 0 Extended SPIs implemented
[ 0.000000] GICv3: Distributor has no Range Selector support
[ 0.000000] Root IRQ handler: gic_handle_irq
[ 0.000000] GICv3: 16 PPIs implemented
[ 0.000000] GICv3: CPU0: found redistributor 0 region 0:0x000000003ffd0000
[ 0.000000] arch_timer: cp15 timer(s) running at 24.57MHz (virt).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x5ab00a189, max_idle_ns: 440795202599 ns
[ 0.000000] sched_clock: 56 bits at 24MHz, resolution 40ns, wraps every 4398046511099ns
[ 0.000062] arm-pv: using stolen time PV
[ 0.000271] Console: colour dummy device 80x25
[ 0.000320] Calibrating delay loop (skipped), value calculated using timer frequency.. 49.15 BogoMIPS (lpj=24576)
[ 0.000324] pid_max: default: 32768 minimum: 301
[ 0.000385] LSM: Security Framework initializing
[ 0.000407] Yama: becoming mindful.
[ 0.000490] Mount-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.000500] Mountpoint-cache hash table entries: 512 (order: 0, 4096 bytes, linear)
[ 0.002706] rcu: Hierarchical SRCU implementation.
[ 0.004135] EFI services will not be available.
[ 0.004315] smp: Bringing up secondary CPUs ...
[ 0.004317] smp: Brought up 1 node, 1 CPU
[ 0.004319] SMP: Total of 1 processors activated.
[ 0.004322] CPU features: detected: 32-bit EL0 Support
[ 0.004323] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[ 0.004325] CPU features: detected: Common not Private translations
[ 0.004326] CPU features: detected: CRC32 instructions
[ 0.004328] CPU features: detected: RCpc load-acquire (LDAPR)
[ 0.004329] CPU features: detected: LSE atomic instructions
[ 0.004330] CPU features: detected: Privileged Access Never
[ 0.004331] CPU features: detected: RAS Extension Support
[ 0.004339] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[ 0.040419] CPU: All CPU(s) started at EL1
[ 0.040435] alternatives: patching kernel code
[ 0.041279] devtmpfs: initialized
[ 0.041694] Registered cp15_barrier emulation handler
[ 0.041699] Registered setend emulation handler
[ 0.041765] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.041769] futex hash table entries: 256 (order: 2, 16384 bytes, linear)
[ 0.041999] pinctrl core: initialized pinctrl subsystem
[ 0.042305] DMI not present or invalid.
[ 0.042538] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[ 0.042898] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[ 0.043056] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[ 0.043204] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[ 0.043214] audit: initializing netlink subsys (disabled)
[ 0.043454] thermal_sys: Registered thermal governor 'fair_share'
[ 0.043455] thermal_sys: Registered thermal governor 'bang_bang'
[ 0.043456] thermal_sys: Registered thermal governor 'step_wise'
[ 0.043457] thermal_sys: Registered thermal governor 'user_space'
[ 0.043457] thermal_sys: Registered thermal governor 'power_allocator'
[ 0.043465] cpuidle: using governor ladder
[ 0.043467] cpuidle: using governor menu
[ 0.043518] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.043524] ASID allocator initialised with 65536 entries
[ 0.043836] Serial: AMBA PL011 UART driver
[ 0.046243] audit: type=2000 audit(0.042:1): state=initialized audit_enabled=0 res=1
[ 0.046364] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages
[ 0.046365] HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages
[ 0.046366] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages
[ 0.046367] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 0.046565] cryptd: max_cpu_qlen set to 1000
[ 0.063702] raid6: neonx8 gen() 21845 MB/s
[ 0.080749] raid6: neonx8 xor() 18988 MB/s
[ 0.097796] raid6: neonx4 gen() 22290 MB/s
[ 0.114844] raid6: neonx4 xor() 17047 MB/s
[ 0.131889] raid6: neonx2 gen() 18187 MB/s
[ 0.148933] raid6: neonx2 xor() 16116 MB/s
[ 0.165978] raid6: neonx1 gen() 15432 MB/s
[ 0.183046] raid6: neonx1 xor() 14419 MB/s
[ 0.200402] raid6: int64x8 gen() 9719 MB/s
[ 0.217449] raid6: int64x8 xor() 5117 MB/s
[ 0.234493] raid6: int64x4 gen() 9341 MB/s
[ 0.251540] raid6: int64x4 xor() 5090 MB/s
[ 0.268585] raid6: int64x2 gen() 8131 MB/s
[ 0.285631] raid6: int64x2 xor() 4207 MB/s
[ 0.302676] raid6: int64x1 gen() 6389 MB/s
[ 0.319721] raid6: int64x1 xor() 3552 MB/s
[ 0.319724] raid6: using algorithm neonx4 gen() 22290 MB/s
[ 0.319725] raid6: .... xor() 17047 MB/s, rmw enabled
[ 0.319726] raid6: using neon recovery algorithm
[ 0.319810] ACPI: Interpreter disabled.
[ 0.320010] iommu: Default domain type: Translated
[ 0.320012] iommu: DMA domain TLB invalidation policy: strict mode
[ 0.320055] vgaarb: loaded
[ 0.320277] SCSI subsystem initialized
[ 0.320371] usbcore: registered new interface driver usbfs
[ 0.320383] usbcore: registered new interface driver hub
[ 0.320390] usbcore: registered new device driver usb
[ 0.320436] pps_core: LinuxPPS API ver. 1 registered
[ 0.320437] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.320439] PTP clock support registered
[ 0.320519] EDAC MC: Ver: 3.0.0
[ 0.320768] Advanced Linux Sound Architecture Driver Initialized.
[ 0.320982] NetLabel: Initializing
[ 0.320983] NetLabel: domain hash size = 128
[ 0.320984] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 0.321000] NetLabel: unlabeled traffic allowed by default
[ 0.321090] clocksource: Switched to clocksource arch_sys_counter
[ 0.321255] VFS: Disk quotas dquot_6.6.0
[ 0.321270] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.321333] pnp: PnP ACPI: disabled
[ 0.322403] NET: Registered PF_INET protocol family
[ 0.322480] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear)
[ 0.322840] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear)
[ 0.322848] TCP established hash table entries: 2048 (order: 2, 16384 bytes, linear)
[ 0.322873] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear)
[ 0.322913] TCP: Hash tables configured (established 2048 bind 2048)
[ 0.323018] MPTCP token hash table entries: 256 (order: 0, 6144 bytes, linear)
[ 0.323033] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.323044] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
[ 0.323073] NET: Registered PF_UNIX/PF_LOCAL protocol family
[ 0.323264] RPC: Registered named UNIX socket transport module.
[ 0.323266] RPC: Registered udp transport module.
[ 0.323266] RPC: Registered tcp transport module.
[ 0.323267] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.323268] PCI: CLS 0 bytes, default 64
[ 0.323333] kvm [1]: HYP mode not available
[ 0.323520] Initialise system trusted keyrings
[ 0.323652] workingset: timestamp_bits=46 max_order=16 bucket_order=0
[ 0.324672] zbud: loaded
[ 0.325157] NFS: Registering the id_resolver key type
[ 0.325169] Key type id_resolver registered
[ 0.325170] Key type id_legacy registered
[ 0.325189] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[ 0.325192] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[ 0.325207] ntfs3: Max link count 4000
[ 0.325208] ntfs3: Read-only LZX/Xpress compression included
[ 0.325235] SGI XFS with ACLs, security attributes, quota, no debug enabled
[ 0.334012] NET: Registered PF_ALG protocol family
[ 0.334016] xor: measuring software checksum speed
[ 0.334475] 8regs : 22289 MB/sec
[ 0.334872] 32regs : 26656 MB/sec
[ 0.335122] arm64_neon : 44102 MB/sec
[ 0.335123] xor: using function: arm64_neon (44102 MB/sec)
[ 0.335146] Key type asymmetric registered
[ 0.335147] Asymmetric key parser 'x509' registered
[ 0.335181] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[ 0.335216] io scheduler mq-deadline registered
[ 0.335217] io scheduler kyber registered
[ 0.335234] io scheduler bfq registered
[ 0.336120] pci-host-generic 10000.pci: host bridge /pci ranges:
[ 0.336133] pci-host-generic 10000.pci: MEM 0x0002000000..0x0003ffffff -> 0x0002000000
[ 0.336136] pci-host-generic 10000.pci: MEM 0x0090800000..0xffffffffff -> 0x0090800000
[ 0.336139] pci-host-generic 10000.pci: Memory resource size exceeds max for 32 bits
[ 0.336141] PCI: OF: PROBE_ONLY enabled
[ 0.336151] pci-host-generic 10000.pci: ECAM at [mem 0x00010000-0x0100ffff] for [bus 00]
[ 0.336173] pci-host-generic 10000.pci: PCI host bridge to bus 0000:00
[ 0.336175] pci_bus 0000:00: root bus resource [mem 0x02000000-0x03ffffff]
[ 0.336176] pci_bus 0000:00: root bus resource [mem 0x90800000-0xffffffffff]
[ 0.336263] pci 0000:00:00.0: [8086:1237] type 00 class 0x060000
[ 0.336641] pci 0000:00:01.0: [1af4:1042] type 00 class 0x00ff00
[ 0.336710] pci 0000:00:01.0: reg 0x10: [mem 0x02000000-0x02007fff]
[ 0.337115] pci 0000:00:02.0: [1af4:1044] type 00 class 0x00ff00
[ 0.337160] pci 0000:00:02.0: reg 0x10: [mem 0x02008000-0x0200ffff]
[ 0.337532] pci 0000:00:03.0: [1af4:1045] type 00 class 0x00ff00
[ 0.337590] pci 0000:00:03.0: reg 0x10: [mem 0x02010000-0x02017fff]
[ 0.338005] pci 0000:00:04.0: [1b73:1000] type 00 class 0x0c0330
[ 0.338051] pci 0000:00:04.0: reg 0x10: [mem 0x02020000-0x0202ffff]
[ 0.338280] pci 0000:00:05.0: [1b36:0011] type 00 class 0xffff00
[ 0.338324] pci 0000:00:05.0: reg 0x10: [mem 0x02018000-0x0201800f]
[ 0.338601] pci 0000:00:00.0: Limiting direct PCI/PCI transfers
[ 0.338810] IPMI message handler: version 39.2
[ 0.340673] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.341038] printk: console [ttyS0] disabled
[ 0.341056] 3f8.U6_16550A: ttyS0 at MMIO 0x3f8 (irq = 13, base_baud = 115200) is a 16550A
[ 0.435958] printk: console [ttyS0] enabled
[ 0.436464] 2f8.U6_16550A: ttyS1 at MMIO 0x2f8 (irq = 14, base_baud = 115200) is a 16550A
[ 0.437278] 3e8.U6_16550A: ttyS2 at MMIO 0x3e8 (irq = 13, base_baud = 115200) is a 16550A
[ 0.438016] 2e8.U6_16550A: ttyS3 at MMIO 0x2e8 (irq = 14, base_baud = 115200) is a 16550A
[ 0.438946] msm_serial: driver initialized
[ 0.439964] cacheinfo: Unable to detect cache hierarchy for CPU 0
[ 0.441149] virtio_blk virtio0: [vda] 5104 512-byte logical blocks (2.61 MB/2.49 MiB)
[ 0.453696] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.454270] ehci-pci: EHCI PCI platform driver
[ 0.454594] ehci-platform: EHCI generic platform driver
[ 0.454966] ehci-orion: EHCI orion driver
[ 0.455348] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.455993] ohci-pci: OHCI PCI platform driver
[ 0.456383] ohci-platform: OHCI generic platform driver
[ 0.456811] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.457630] xhci_hcd 0000:00:04.0: xHCI Host Controller
[ 0.458104] xhci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1
[ 0.459156] xhci_hcd 0000:00:04.0: hcc params 0x30000501 hci version 0x110 quirks 0x0000000000080452
[ 0.460161] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.16
[ 0.460851] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.461608] usb usb1: Product: xHCI Host Controller
[ 0.462011] usb usb1: Manufacturer: Linux 5.16.13-1-aarch64-ARCH xhci-hcd
[ 0.462646] usb usb1: SerialNumber: 0000:00:04.0
[ 0.463143] hub 1-0:1.0: USB hub found
[ 0.463495] hub 1-0:1.0: 8 ports detected
[ 0.464194] xhci_hcd 0000:00:04.0: xHCI Host Controller
[ 0.464627] xhci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2
[ 0.465279] xhci_hcd 0000:00:04.0: Host supports USB 3.0 SuperSpeed
[ 0.465775] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 0.466639] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.16
[ 0.467436] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.468076] usb usb2: Product: xHCI Host Controller
[ 0.468511] usb usb2: Manufacturer: Linux 5.16.13-1-aarch64-ARCH xhci-hcd
[ 0.469285] usb usb2: SerialNumber: 0000:00:04.0
[ 0.469718] hub 2-0:1.0: USB hub found
[ 0.470134] hub 2-0:1.0: 8 ports detected
[ 0.470916] SPI driver max3421-hcd has no spi_device_id for maxim,max3421
[ 0.471647] usbcore: registered new interface driver uas
[ 0.472196] usbcore: registered new interface driver usb-storage
[ 0.472728] usbcore: registered new interface driver ums-alauda
[ 0.473262] usbcore: registered new interface driver ums-cypress
[ 0.473811] usbcore: registered new interface driver ums-datafab
[ 0.474339] usbcore: registered new interface driver ums_eneub6250
[ 0.474857] usbcore: registered new interface driver ums-freecom
[ 0.475381] usbcore: registered new interface driver ums-isd200
[ 0.475872] usbcore: registered new interface driver ums-jumpshot
[ 0.476471] usbcore: registered new interface driver ums-karma
[ 0.476980] usbcore: registered new interface driver ums-onetouch
[ 0.477628] usbcore: registered new interface driver ums-realtek
[ 0.478187] usbcore: registered new interface driver ums-sddr09
[ 0.478692] usbcore: registered new interface driver ums-sddr55
[ 0.479190] usbcore: registered new interface driver ums-usbat
[ 0.479673] usbcore: registered new interface driver usbserial_generic
[ 0.480210] usbserial: USB Serial support registered for generic
[ 0.480937] mousedev: PS/2 mouse device common for all mice
[ 0.482039] device-mapper: uevent: version 1.0.3
[ 0.482585] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: [email protected]
[ 0.483635] sdhci: Secure Digital Host Controller Interface driver
[ 0.484165] sdhci: Copyright(c) Pierre Ossman
[ 0.484597] Synopsys Designware Multimedia Card Interface Driver
[ 0.485538] sdhci-pltfm: SDHCI platform and OF driver helper
[ 0.486181] ledtrig-cpu: registered to indicate activity on CPUs
[ 0.486938] hid: raw HID events driver (C) Jiri Kosina
[ 0.487505] usbcore: registered new interface driver usbhid
[ 0.488046] usbhid: USB HID core driver
[ 0.489286] Initializing XFRM netlink socket
[ 0.489884] NET: Registered PF_INET6 protocol family
[ 0.492003] Segment Routing with IPv6
[ 0.492396] In-situ OAM (IOAM) with IPv6
[ 0.492901] mip6: Mobile IPv6
[ 0.493198] NET: Registered PF_PACKET protocol family
[ 0.493793] Key type dns_resolver registered
[ 0.494390] registered taskstats version 1
[ 0.494742] Loading compiled-in X.509 certificates
[ 0.495343] zswap: loaded using pool lzo/zbud
[ 0.495785] debug_vm_pgtable: [debug_vm_pgtable ]: Validating architecture page table helpers
[ 0.496723] Key type ._fscrypt registered
[ 0.497098] Key type .fscrypt registered
[ 0.497514] Key type fscrypt-provisioning registered
[ 0.498375] Btrfs loaded, crc32c=crc32c-generic, zoned=yes, fsverity=no
[ 0.499191] Key type encrypted registered
[ 0.657459] ALSA device list:
[ 0.657786] No soundcards found.
[ 0.658355] md: Waiting for all devices to be available before autodetect
[ 0.658953] md: If you don't use raid, use raid=noautodetect
[ 0.659460] md: Autodetecting RAID arrays.
[ 0.659861] md: autorun ...
[ 0.660147] md: ... autorun DONE.
[ 0.664078] F2FS-fs (vda): Magic Mismatch, valid(0xf2f52010) - read(0x98375fa1)
[ 0.664970] F2FS-fs (vda): Can't find valid F2FS filesystem in 1th superblock
[ 0.666059] F2FS-fs (vda): Magic Mismatch, valid(0xf2f52010) - read(0x65e3faa7)
[ 0.666714] F2FS-fs (vda): Can't find valid F2FS filesystem in 2th superblock
[ 0.670343] F2FS-fs (vda): Magic Mismatch, valid(0xf2f52010) - read(0x98375fa1)
[ 0.671002] F2FS-fs (vda): Can't find valid F2FS filesystem in 1th superblock
[ 0.672025] F2FS-fs (vda): Magic Mismatch, valid(0xf2f52010) - read(0x65e3faa7)
[ 0.672732] F2FS-fs (vda): Can't find valid F2FS filesystem in 2th superblock
[ 0.673553] List of all partitions:
[ 0.673850] fd00 2552 vda
[ 0.673853] driver: virtio_blk
[ 0.674375] No filesystem could mount root, tried:
[ 0.674377] ext3
[ 0.674706] ext2
[ 0.674854] ext4
[ 0.674988] vfat
[ 0.675161] msdos
[ 0.675411] ntfs3
[ 0.675683] xfs
[ 0.675867] f2fs
[ 0.676014] btrfs
[ 0.676172]
[ 0.676436] Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(253,0)
[ 0.677087] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.16.13-1-aarch64-ARCH #1
[ 0.677776] Hardware name: linux,dummy-virt (DT)
[ 0.678237] Call trace:
[ 0.678497] dump_backtrace+0x0/0x1cc
[ 0.678848] show_stack+0x18/0x24
[ 0.679114] dump_stack_lvl+0x68/0x84
[ 0.679447] dump_stack+0x18/0x34
[ 0.679729] panic+0x138/0x308
[ 0.679991] mount_block_root+0x1e0/0x1fc
[ 0.680365] mount_root+0x150/0x170
[ 0.680707] prepare_namespace+0x134/0x174
[ 0.681151] kernel_init_freeable+0x20c/0x244
[ 0.681573] kernel_init+0x28/0x140
[ 0.681889] ret_from_fork+0x10/0x20
[ 0.682201] Kernel Offset: disabled
[ 0.682483] CPU features: 0x00,00000302,46600e42
[ 0.682904] Memory Limit: none
[INFO:external/crosvm/src/linux/vcpu.rs:470] system reset event
[INFO:external/crosvm/src/linux/mod.rs:1830] vcpu requested reset
[ERROR:external/crosvm/src/linux/vcpu.rs:739] failed to send VcpuControl: sending on a closed channel
[INFO:external/crosvm/src/main.rs:2872] crosvm has exited normally due to reset request.
Can someone show me how they got it to run?
Thanks Ron

Hi Ron / @cron5918. Welcome to XDA. Please in the future use either [quote]stuff[/quote] or [spoiler="Name of stuff"]stuff[/spoiler] for super-long segments of logs or code.
You can Edit your post and insert those items any time if you wouldn't mind. Disregard.

Hi headheadhead
Which cloud image did you use? I tried a couple and got no path to disk

I tried Ron's way also, no luck

rgarcia1000 said:
Hi headheadhead
Which cloud image did you use? I tried a couple and got no path to disk
Click to expand...
Click to collapse
The image I used is this.

Hi Head,
I read what you wrote to Rich..
You are running amd64 on the pixel?

How are you guys getting / building your kernels? Been trying to get this to work too.

cron5918 said:
Hi Head,
I read what you wrote to Rich..
You are running amd64 on the pixel?
Click to expand...
Click to collapse
Sorry for the mistake. I ran arm64 on pixel. lt is now corrected.

blundergat said:
How are you guys getting / building your kernels? Been trying to get this to work too.
Click to expand...
Click to collapse
Use the Linux mainline kernel. You can find several tutorials about building the Linux mainline kernel.

blundergat said:
How are you guys getting / building your kernels? Been trying to get this to work too.
Click to expand...
Click to collapse
I used Linux 5.17-rc3 and compiled.
>make ARCH=aarm64 with allnoconfig. then I edit the .config file for kvm.
But I still can't get it to mount the root file system.

Been asking for this also, I don't know if I am building the Kernel right.
Head if it is not too much trouble can you show use what you did to build the kernel?

rgarcia1000 said:
I used Linux 5.17-rc3 and compiled.
>make ARCH=aarm64 with allnoconfig. then I edit the .config file for kvm.
But I still can't get it to mount the root file system.
Click to expand...
Click to collapse
Thanks for the pointer! I've built kernels in the past but forgive me for such a stupid question. You're building this on your pc not your phone right? I keep getting this error on Arch.
Code:
Makefile:625: arch/aarm64/Makefile: No such file or directory
However I can build doing "make ARCH=arm64".