Related
Would appreciate your help on the following issue (amoled display):
- phone doesnt boot up, it is stuck to a screen showing htc in the middle and 4 small triangles in the corners; if I unplug the pc cable it goes to a RUU menu
- no access to recovery or bootloader menus (by holding power + vol down/back)
- installing stock RUUs dont work; there is a 110 error saying that the RUU is not complete (tried 5-6 RUUs, both 2.1 and 2.2). there is a progress bar on the phone's screen that is normally green, but turns red when the radio is being written (as per the install wizard on the pc) and there is another triangle showing up at the end of the progress bar
- fastboot oem boot restarts the phone, but then it gets stuck to the white screen having htc in the middle (like when you start up the phone and after this quietly brilliant shows under htc, for me it doesnt go beyond this initial point)
- fastboot reboot-bootloader restarts the phone into the same 4triangles screen with htc in the middle
- adb doesnt work as it doesnt show my device
- any power + vol down/back combination brings the phone to the 4triangles screen
- if I run the stock RUU after fastboot oem boot (white screen with htc in the middle) there is a menu showing up on top of the white screen showing up the progress (1-bootloader, 2-radio_v2, 3-radio, then system, recovery, user data, etc.); bootloader is updated ok but then it gets stuck when updating radio_v2 and doesnt move further from that point)
- after the RUU install fails, I plug out the pc cable and see the RUU menu; depending on the RUU that I try to flash the hboot version changes up and even goes down after, but the firmware (what the RUU installer "sees" on the phone) and radio (seen on the RUU menu) remains the same: 1.21.405.1 and 4.06xx; the date on the RUU menu also changes depending on the RUU that I try to flash
Any suggestions to get my desire unbricked?
Bit of a background to the problem:
- rooted (unlockr) and was having Paul's r3 rom (2.1)
- updated the radio to 5.10xx
- got into silly restarts when using gps and thought to reflash a new rom and went for Paul's r8
- restarts were there also when using the phone normally
- thought to re-do all the rooting, wiping out everything from the phone, etc; so having r8 as the rom (pre-baked version) I started the rooting process with creating again the goldcard, etc etc
- error message at some point saying partition update fail (following the steps from theunlockr as I did the first time when rooting) and then the phone got to this triangles screen with htc in the middle
- strange though that this screen is different than the one when I first rooted when there was just one big triangle in the middle
Thanks a ton guys!
I've seen a few posts about this screen with the 4 triangles, but never seen the result of any potential fixes, or if it was ever actually fixed.
Just an idea, but it was maybe a bad radio flash if you are saying it started playing up after that? Unfortunately a bad radio flash is fairly terminal so I hope that's not your problem.
Good luck with this one and if you get it fixed then post the result here if you don't mind!
Will definitely post the solution when found; so far though nobody has any thoughts around what might be the reason behind this problem and how to get around it. I dropped a few PMs to the people that had this problem in the past and contacted Paul at Modaco, but so far no replies...
You can fix this with an RUU, I've had the same issue when I unplugged too early after flashing, but you are asking for help in the wrong section.
thought that the dev's section is where the best knowledge exists...
about the RUU process, I am trying to flash stock RUU.exe files, but there is a problem when the radio is being written and then I get a 110 error from the RUU install wizard saying that the RUU is incomplete.
for you the RUU install worked smoothly?
If you get a write error during an RUU flash (i.e. while the flashing is taking place, not before) it probably means there's a hardware fault.
Could be hardware, but I find it hard to believe as the phone is new and it is network locked, hence I didnt even use it for real, apart from some wifi and gps activities. Besides, the phone worked very well when I first rooted with Paul's r3 and the whole mess with restarts when using gps started after I upgraded the radio to 5.10xx having a 2.1 OS.
I feel that the problem started when I tried to root the phone being on Paul's r8 2.2 OS (tried to root with a 2.1 system and then it got messed up in the process).
I am not saying that it is not hardware as it is a possibility, but still think that it might be a messy software aspect, as if the radio is messed up from a hardware perspective, then at least the system should boot up and then wifi, gps, gsm and the things that are controlled by the radio shouldnt work...but somehow the OS should start-up.
Basically I dont get a write error, it's just that the error comes up when the radio is being written, hence I think that there is something wrong with the radio set-up that I have now on the phone...
Maybe somebody knows how to flash the system from scratch using only fastboot in cmd (having the right zip or img files properly signed), or maybe just the radio to start with.
This is not a Development question and thus should not be posted in the Development forum.
Thread reported.
have a look here. i do not know if it helps though. and i know it is not a Desire
http://forum.ppcgeeks.com/htc-hero/118035-error-110-ruu.html
i also found this. sounds familiar? not for desire but might do the trick http://forum.androidcentral.com/htc-hero-roms-hacks/13171-110-error-ruu-1-56-fix-100-unroot-too.html
sorry if i wasted your time.
acolwill said:
This is not a Development question and thus should not be posted in the Development forum.
Thread reported.
Click to expand...
Click to collapse
Well, I thought that as various solutions to root the phone, to get past different restrictions in the OS, etc. were discussed here, it might be a good thing to develop a way to bring back to life a OS being in this situation like mine...come on...
mariosraptor said:
have a look here. i do not know if it helps though. and i know it is not a Desire
http://forum.ppcgeeks.com/htc-hero/118035-error-110-ruu.html
i also found this. sounds familiar? not for desire but might do the trick http://forum.androidcentral.com/htc-hero-roms-hacks/13171-110-error-ruu-1-56-fix-100-unroot-too.html
sorry if i wasted your time.
Click to expand...
Click to collapse
Thanks anyways man, I looked at that already, but cant get it done as I dont have adb commands available in cmd, only fastboot. Dont worry about waisting my time, I really want that these days
I had the same problem. Passed the device in service center. Changed the motherboard under warranty. It took one month's time.
but to get adb you need to download and install android sdk. look here http://developer.android.com/sdk/index.html system dependands download.
install it here are instructions on how to use if you aren't familiar with.
http://www.londatiga.net/it/how-to-use-android-adb-command-line-tool/
for anything else just use google.
i'm pretty sure that your device is fixable and you can fix it without any service center. cheers and post what ever happens.
popepope said:
Thanks anyways man, I looked at that already, but cant get it done as I dont have adb commands available in cmd, only fastboot. Dont worry about waisting my time, I really want that these days
Click to expand...
Click to collapse
I know how to use adb commands...pretty new to android and everything, but lately I roamed a lot through various things about it and learned a lot.
The problem is that adb doesnt list my phone when I run adb devices, it shows only when I run fastboot devices, I am sure you know what I mean...hence I cannot push any files to the phone, etc., at least not using adb in cmd.
That's actually the problem, that I cannot get adb to work, I only have fastboot commands. At least the way I see it now the question is how can I work with the phone to fix it just by having fastboot access in cmd.
I searched quite a lot various forums, etc, but I never came across a solution that will get things going just by having fastboot in cmd (without adb working). Maybe somebody here will come up with some magic trick...
Nerten said:
I had the same problem. Passed the device in service center. Changed the motherboard under warranty. It took one month's time.
Click to expand...
Click to collapse
How did you end up having this problem, just like that or after some update, flash, etc?
Thanks!
have a look here mate http://forum.androidcentral.com/htc...9-bricked-my-evo-but-there-away-un-brick.html
same story unfortunately, doesnt apply to my problem. in the link they use a terminal emulator, but I cant use that as it doesnt work...it's basically an alternative to using adb directly in cmd, and this doesnt work for me.
if I am to get adb functionality back, then I'm done with the problem in 5 mins probably...
thanks anyways, keeping the hope alive!
sorry idf i don't underdstand, but if you have fastboot working in your device and sdcard also then you should be able to push files to device via fastboot making as clean installs as possible.so if your device is picked up by command line type fastboot to see command list. i'am a bit comfused. pretty sure you should fix it through fastboot though.
popepope said:
same story unfortunately, doesnt apply to my problem. in the link they use a terminal emulator, but I cant use that as it doesnt work...it's basically an alternative to using adb directly in cmd, and this doesnt work for me.
if I am to get adb functionality back, then I'm done with the problem in 5 mins probably...
thanks anyways, keeping the hope alive!
Click to expand...
Click to collapse
right, I can run 2 things with fastboot in cmd: (name of the files just an example)
1. fastboot update update.zip
here I get that the archive doesnt contain android-info.txt or android-product.txt
2. fastboot flash update.img
here i get signature verify fail
for example, fastboot erase radio says FAILED, remote: not allowed
there are some fastboot commands related to the kernel and some others, but dont know how to make use of them for my problem.
sd card is accesible for sure and it is a goldcard.
I saw some linux/ubuntu methods to simulate adb usage in cmd, but I dont think it will work...will try to find an ubuntu image and mount it under windows, but dont have time now...
anyways, thanks to everybody for the suggestions and interest, maybe we'll crack it some day
You need to use an official RUU zip image - i.e. a PB99IMG.zip. Not an update.zip.
the phone is a sprint gnex.
i had twrp as recovery, and i was playing around with it, got distracted, and my 2 year old grabbed it and wiped everything. no OS, no recovery, no nothing.
i'm not even sure where to start. my newbie self is thinking maybe odin? i used adb once, is that where i should be looking?
i guess my question is where does one start when he has no OS. and i could sure use a link for wherever factory images, or tar files, or whatever, are reposed.
please help a brother out, and keep in mind i am in fact over my head. just trying to salvage this if possible. it is not an urgent thing, as i the device is merely used as a media device for my 2 year old.
my laptop is a windows 7 device. i've downloaded usb drivers for samsung, odin, and adb fastboot. they are sitting in my download folder as zip files. that is where i stand.
boathead said:
the phone is a sprint gnex.
i had twrp as recovery, and i was playing around with it, got distracted, and my 2 year old grabbed it and wiped everything. no OS, no recovery, no nothing.
i'm not even sure where to start. my newbie self is thinking maybe odin? i used adb once, is that where i should be looking?
i guess my question is where does one start when he has no OS. and i could sure use a link for wherever factory images, or tar files, or whatever, are reposed.
please help a brother out, and keep in mind i am in fact over my head. just trying to salvage this if possible. it is not an urgent thing, as i the device is merely used as a media device for my 2 year old.
my laptop is a windows 7 device. i've downloaded usb drivers for samsung, odin, and adb fastboot. they are sitting in my download folder as zip files. that is where i stand.
Click to expand...
Click to collapse
Don't worry you'll be fine.
If you can get into twrp, try just downloading a ROM and gapps zip on computer and using adb to push or sideload to device (Google "adb sideload ROM galaxy nexus...exact steps easy to find)
If you can't get into recovery, or just want to go back to complete stock and start from there, go here https://developers.google.com/android/nexus/images
Grab a package for sprint gnex(mysidspr, aka toroplus) and if u have adb&fastboot installed on computer(if not then Google "installing android SDK" and it will be top result, fastboot and adb come WITH the SDK when u install it)
Then you just unzip that factory img file, plug device into computer while in boot loader mode (hold power and both volume keys), open the folder created when u uncompressed factory IMG file, hold down shift and right click and choose "open command prompt". Enter "fastboot devices"(no quotes) in the command window to make sure device is recognized. Then just run "flash-all.exe" or "flash-all.bat" in command prompt and BE PATIENT AND LET IT FINISH EVERYTHING. After that device will be like brand new out of box.
ashclepdia said:
Don't worry you'll be fine.
If you can get into twrp, try just downloading a ROM and gapps zip on computer and using adb to push or sideload to device (Google "adb sideload ROM galaxy nexus...exact steps easy to find)
If you can't get into recovery, or just want to go back to complete stock and start from there, go here https://developers.google.com/android/nexus/images
Grab a package for sprint gnex(mysidspr, aka toroplus) and if u have adb&fastboot installed on computer(if not then Google "installing android SDK" and it will be top result, fastboot and adb come WITH the SDK when u install it)
Then you just unzip that factory img file, plug device into computer while in boot loader mode (hold power and both volume keys), open the folder created when u uncompressed factory IMG file, hold down shift and right click and choose "open command prompt". Enter "fastboot devices"(no quotes) in the command window to make sure device is recognized. Then just run "flash-all.exe" or "flash-all.bat" in command prompt and BE PATIENT AND LET IT FINISH EVERYTHING. After that device will be like brand new out of box.
Click to expand...
Click to collapse
thank you so much for responding. i will play around with this later, but it is a bit comforting to know that maybe i'm not doomed.
i cannot get into recovery, so yeah, i don't know what i'm doing.
boathead said:
thank you so much for responding. i will play around with this later, but it is a bit comforting to know that maybe i'm not doomed.
i cannot get into recovery, so yeah, i don't know what i'm doing.
Click to expand...
Click to collapse
Why can't you get into recovery?
Are you choosing recovery mode via the bootloader menu? I didn't think it was POSSIBLE to wipe recovery from within recovery.
Even if you can't, trust me, Doing a factory img restore, or using fastboot to flash custom recovery again is VERY easy. To get the SDK that has needed fastboot tools, go here http://developer.android.com/sdk/index.html#ExistingIDE
And grab the needed exe for your setup(windows 64 or 32bit). Make sure you are getting the "ADT bundle" it's what has needed platform tools. Then just run the exe and follow instructions.
Now u COULD also just Google search for Wugfresg toolkit, and download and use that. Its very easy to use as well. I just prefer to have adb and fastboot installed to my computer so that I can always be good to go. Plus I use Linux so Im not able to use Wugfresh, but knowing how to just use fastboot and adb also makes ya feel like a boss(even though is pretty simple lol)
Don't worry, there is hope, and it's not gonna be difficult. You'll be up again in no time.
because you said you didn't think it was possible to wipe recovery from recovery, i went into bootloader. you are correct. in my panic i overlooked it. i DO in fact still have twrp.
but there is nothing to restore or install. so once my phone charges, i'll give it a shot as you suggested. would you kindly check in later in case i need some more help?
thanks my friend for steering me in the correct direction.
boathead said:
because you said you didn't think it was possible to wipe recovery from recovery, i went into bootloader. you are correct. in my panic i overlooked it. i DO in fact still have twrp.
but there is nothing to restore or install. so once my phone charges, i'll give it a shot as you suggested. would you kindly check in later in case i need some more help?
thanks my friend for steering me in the correct direction.
Click to expand...
Click to collapse
Of course!
I'm always checking in these forums, and I use Tapatalk, and have actually grown fond of Tapatalk notifications, so I SHOULD get a notif if you post back or PM(though I prefer to keep in thread, that way someone else searching for answer to similar issue can find a helpful thread as well)
Yea it sounds like your little one got into twrp and most likely wiped all of /data and /system. Instead of just a regular factory reset which would have left your stuff like flashable zips and all still in /sdcard. That sucks! I've actually done that on accideHahaha
hile back(a mistake you only make once to wipe all of /data AND /system lol, even though can pretty easily be fixed)
Sounds like you could use adb sideload or push to get ROM/gapps zips back on the device, or just go with a total device factory restore, whichever you choose at this point should work just fine.
I'm not sure if there is a way to do this yet, but I've always wanted to put a pin code lock for TWRP. That way if my nephew ever did find his way into there when using my phone, he wouldn't be able to do any damage. If it's not a part of custom recovery yet (I haven't looked actually lol) it would be awesome if someone found a way to add that feature in. Could save a lot of us the hassle in cases like this! Hahaha
I'll check back in the morning and randomly tomorrow (some of the day I won't have a connection, I use Gnex strictly on WiFi) to see if you need any help/tips/clarifying of any steps needed. Once you do this restore process once, you'll be amazed at how easy it can be, and as long as you keep the files on your laptop, you'll be ready to go if you ever need to do it again.
success!
i had a great deal of trouble sorting the drivers....took quite a while to get the pc to recognize the device. then i got confused about a few things...stunner, i know, but was able to reflash a factory image with the wug toolkit. so i guess i took the cowardly way and didn't do the adb route.
anyway, i'm good to go. i am left with the initial problem that had me in recovery in the first place. i figured flashing a rom would solve it, but no. so i'm left thinking it is on the server side. at least i have something to work with now.
so thanks again. without your calming words i never would have gotten this going. i don't have the temperament to play around with my devices, i've learned.
boathead said:
success!
i had a great deal of trouble sorting the drivers....took quite a while to get the pc to recognize the device. then i got confused about a few things...stunner, i know, but was able to reflash a factory image with the wug toolkit. so i guess i took the cowardly way and didn't do the adb route.
anyway, i'm good to go. i am left with the initial problem that had me in recovery in the first place. i figured flashing a rom would solve it, but no. so i'm left thinking it is on the server side. at least i have something to work with now.
so thanks again. without your calming words i never would have gotten this going. i don't have the temperament to play around with my devices, i've learned.
Click to expand...
Click to collapse
That temperament is something that is gained. MOST of us have been in that "oh holy crap what do I do now?!?! Im not prepared for this!!" Moments (my first one was on my birthday back when I had DroidX2, and didn't have my own computer to restore it using RSDlite sbf flash.. I accidentally flashed something that didn't work, and was left with no OS stuck in bootloop with no way to get into the bootstrap recovery we had...was without device for 3 days until I could get to a coworkers laptop!! Lol!!!) But the stress goes WAY down after you've restored device once or twice and have the tools at the ready with basic understanding of the steps at least
And as for drivers, I apologize for not warning/informing about that. I forgot that you mentioned you had multiple driver packages downloaded and i was going to clarify which to use(on a Linux setup you don't need drivers and it been a while since I used windows for my device so drivers aren't usually on my mind lol) I think a lot of people use the PDAnet drivers. But if you are connected to internet and just put device in fastboot mode and connect to computer, I think it will automatically find and install the correct drivers needed for fastboot/adb access.(the toolkit can also be used to install correct drivers I believe)
And don't worry, I wouldn't call using toolkit the "cowardly way". SOME people detest/despise use of toolkit since they think it takes away from learning and understanding how to do it without a toolkit. But when you use a toolkit you usually see command prompt correct? (Or at least a setting so you can SEE what it is running as far as commands) so you get to see what its doing, which helps beginners start to grasp the concepts of what it is doing.
Trust me, if you can use the toolkit correctly, you can easily transfer that knowledge to just using fastboot or adb commands.
by the way, fastboot is what's used for factory image restore. ADB is for pushing/pulling files, taking logs, sideloading a ROM/gapps zip that isn't on device, taking/restoring adb backups of system and or data, things like that. Think of adb as the "taker and giver". And fastboot as the "img installer/booter"...imgs being anything from system img files, to data partition img files, boot.img(aka kernel), recovery.img, bootloader update img, radio imgs. Things like that
The reason the knowledge from using toolkit easily transfers over to using just straight up fastboot for example is because of how they word the choices and menus. You will see it says something like "use fastboot to flash new recovery img", which the fastboot command for that in command line equates to "fastboot flash recovery "NameOfRecoveryImage.img" "
(With no quotes of course, and replace "NameOf...." With the actual file name of the recovery.img you have downloaded, and you can rename the downloaded recovery img file to something easier to type out if you want to also)
Basic structure of using fastboot command would be as follows:
fastboot[space]command[space]partitioname[space]filetobeused
Which after used once or twice is very easy to grasp basic usage
So are you able to at least boot into OS now? Also, make sure if you are trying to flash a KitKat ROM, that you install the 2.7TWRP recovery, anything earlier won't work correctly for 4.4based ROMs.
Again, any trouble feel free to ask.
(And apologies for the long rambling posts lol)
yes. i am in the OS now.
what gave rise to my troubles in the first place is that i've moved my residence. all my devices recognize my new wifi, and proceed along their merry way.
my gnex is another story. it recognized my wifi, shows me as connected, but nothing at all can actually access the server. i tried factory reset, nothing. then i was going to install a new rom, figuring something was corrupted. then my 2 year old took over!
so i am in the OS, but still cannot access the server. so it must be on the server side i figure. not sure how to fix this, but when i have some time, i'll do some looking around. i am going to try to access a different wifi network later on to see if at least it is not my device.
again, thanks for your help my friend.
boathead said:
yes. i am in the OS now.
what gave rise to my troubles in the first place is that i've moved my residence. all my devices recognize my new wifi, and proceed along their merry way.
my gnex is another story. it recognized my wifi, shows me as connected, but nothing at all can actually access the server. i tried factory reset, nothing. then i was going to install a new rom, figuring something was corrupted. then my 2 year old took over!
so i am in the OS, but still cannot access the server. so it must be on the server side i figure. not sure how to fix this, but when i have some time, i'll do some looking around. i am going to try to access a different wifi network later on to see if at least it is not my device.
again, thanks for your help my friend.
Click to expand...
Click to collapse
what security do you use on your router? if WEP try changing it. the gnex has issues sometimes with using WEP secured WiFi AP's
also, if using a 5ghz network, I can only get mine to connect to that on channel 153. there are only a certain number of 5ghz channels supported.
might also want to just try forgetting WiFi network and re add?(if it restored the access points by any means including Google backup/restore)
and make sure your router isn't rejecting the Mac address for some reason(and some people will suggest reboot of the router to see if that helps fix it, which I've seen fix many connection issues)
well, my device works beautifully....everywhere except in my house.:crying:
as much as drivers befuddle me, routers do even more so. it must be a router issue, right? my device connects to google elsewhere. and all my other devices connect to google here at home. maybe tomorrow i'll try the router's live chat to see if i can get some help.
boathead said:
well, my device works beautifully....everywhere except in my house.:crying:
as much as drivers befuddle me, routers do even more so. it must be a router issue, right? my device connects to google elsewhere. and all my other devices connect to google here at home. maybe tomorrow i'll try the router's live chat to see if i can get some help.
Click to expand...
Click to collapse
what type of security are you using in the router setting? WPA? wep? none?
what model router are you using?
is device connecting to internet and just not Google servers?
is device connecting to router at all and just no internet access?(meaning when you are in WiFi settings, and choose network does it show obtaining IP address and then connected? or just never fully connect?)
I've had similar issues in past and might be able to help with some more details
ashclepdia said:
what type of security are you using in the router setting? WPA? wep? none?
what model router are you using?
is device connecting to internet and just not Google servers?
is device connecting to router at all and just no internet access?(meaning when you are in WiFi settings, and choose network does it show obtaining IP address and then connected? or just never fully connect?)
I've had similar issues in past and might be able to help with some more details
Click to expand...
Click to collapse
wpa2...but i've even disable all security to see....i've disable firewalls...nothing. it is an arris router that time warner cable provided when i moved to my new place.
and i my phone does show me as connected to my network...just can't get into google. and the phone works just fine at my work. as you know, i've been through several roms and an entirely new OS...so it cannot be the phone...can it?
been through this entire threads, and no joy.
http://forum.xda-developers.com/showthread.php?t=2110225
if you have any ideas, post away. i will be away from access to the internet for a few days, so i won't even have a chance to check in here, but any info in the meantime would be most thanked.
boathead said:
thank you so much for responding. i will play around with this later, but it is a bit comforting to know that maybe i'm not doomed.
i cannot get into recovery, so yeah, i don't know what i'm doing.
Click to expand...
Click to collapse
my samsung s5 had the same problem. i wiped out everything and it says i have no os no nothing. i hope if anyone can help, i will be pleased.
the only question is that "how can i get an os and get my phone working"
ashclepdia said:
Don't worry you'll be fine.
If you can get into twrp, try just downloading a ROM and gapps zip on computer and using adb to push or sideload to device (Google "adb sideload ROM galaxy nexus...exact steps easy to find)
If you can't get into recovery, or just want to go back to complete stock and start from there, go here https://developers.google.com/android/nexus/images
Grab a package for sprint gnex(mysidspr, aka toroplus) and if u have adb&fastboot installed on computer(if not then Google "installing android SDK" and it will be top result, fastboot and adb come WITH the SDK when u install it)
Then you just unzip that factory img file, plug device into computer while in boot loader mode (hold power and both volume keys), open the folder created when u uncompressed factory IMG file, hold down shift and right click and choose "open command prompt". Enter "fastboot devices"(no quotes) in the command window to make sure device is recognized. Then just run "flash-all.exe" or "flash-all.bat" in command prompt and BE PATIENT AND LET IT FINISH EVERYTHING. After that device will be like brand new out of box.
Click to expand...
Click to collapse
The same thing happened to me right now, while I was installing CM13 in my Lenovo Zuk Z1. I took a backup from TWRP and copied the same to my pc. Then I wiped all the data from my phone using TWRP. Then I plugged in the Usb back to copy the downloaded files of CM13 to my phone but my pc is not showing the Internal Memory of my phone. I am so freaked out right now. I dont have an OS in my phone and I am unable to restore what I backed up. I am just stucked in TWRP. Guide me through to install CM 13 or atleast revert back to where I started. Any help is appreciated.
Short version of question: How can I unbrick my ONEPLUS 3 (A3000) if I cannot boot to Android and OEM Unlock AND USB Debugging both have not been enabled?
Long version: Phone was recently purchased second hand from a third-party market (Kijiji, kind of like craigslist for Canadians). Person I bought it from claimed in the ad that the device was in a bootloop and couldn't access the OS. I had in the past successfully saved a ONEPLUS 1 from bricked status, so I didn't feel a simple bootloop would pose much of an issue. That, and at the price he was selling I really couldn't turn it down.
I tried various different methods of restoring the phone's partitions, OS, and firmware to stock/custom, but had no real luck with any (I will list below what I have attempted). If there was a root cause of this, I believe it's due to the fact that some part of the phone's storage partition (boot or system if I had to guess) had become corrupted at some point. Given the volume of threads I've seen here and elsewhere online, I wouldn't rule out a bad OTA flash, but doesn't really matter. What does matter, however, is that the Android OS is inaccessible despite my best efforts, and the bootloader is set to locked and ADB Debugging remains off.
Generally speaking, is there a way to access Developer Options to correct both these issues through terminal or a tool? I'm confident that I can get my device working again if I could access this menu, but as of yet I have had no luck.
Methods used to restore/info worth mentioning
While I don't doubt their effectiveness at large, for whatever reason I have yet to find a tool/guide that yields the anticipated results upon completion. MSM Download Tool (V3 and V4) have both been downloaded, executed, and completed numerous times, but will still not boot past the loading screen upon completion.
According to Unified Android Toolkit, my device build is being detected as "OnePlus3 7.0 NRD90M" and All-in-One Toolkit is showing that Android 6.0.1 is installed.
Drivers are all installed correctly, as proven both via tools downloaded and through Windows CMD terminal (adb devices, fastboot devices, adb get-state, etc)
Stock recovery and bootloader modes can both be reached through both hardware keys and software commands. I will note that it seems to take longer than I'd expect to boot to either of these modes using hardware keys.
I have utilized multiple USB ports, Type-C cables, different OS' on two laptops (MS Windows 10 and 7, FWUL Linux). I usually have no problem with the device being detected by the system. When I have, it usually involved one pesky USB cord.
common commands used and their effects:
fastboot OEM unlock: fails, cannot be done remotely
fastboot flash x: fails, remote: flashing partitions not allowed
ADB push: fails. cannot access partition
ADB devices: device is seen by system with serial and state
fastboot devices: device is seen by system with serial
ADB sideload: varying results. Some will fail at 0% citing "total xfer: 0.00x", some will reach 47% and fail (always exactly 47% oddly). Generally if the sideload operation passes 47% it will complete.
fastboot format/erase x: fails, partition formatting/erasing not allowed
fastboot continue: executes, but does not help with android bootloop issue as I had hoped
While I searched for an answer online, I did come across an infosec whitepaper regarding ONEPLUS 3 vulnerabilities, though it was over a year old. To my surprise, the command they had been entering works on my device, but I'm not sure how to properly use it effectively. The command used was fastboot OEM boot_mode [rf/wlan/ftm/normal]. Now, I was unable to determine what each of the triggers does, but what I did discover is that with boot_mode set to rf, my device would display chinese/korean lettering in lieu of the usual ONEPLUS logo with "powered by Android" below. This is also how I managed to have my device show up in CMD terminal for ADB commands to be issued. To the best of my knowledge though, there doesn't seem to be much point to it as I couldn't push/pull any files. Does anybody know where I could find more info on this command, as I'd like to know what the other triggers accomplish.
I've just about exhausted every available resource looking for an answer, but im still coming up short. I've gone as far as contacting ONEPLUS directly, but without proof of purchase they can't (more accurately won't) help me. And while it's not a business practice I would personally support, I can understand why they have it implemented. I've contacted a few phone shops in the area, but none have been able to assist me further than I've already gotten in this process.
I apologize again for creating a new thread about this, but I felt my circumstances warranted a new thread due to the bulk of the others having either an unlocked bootloader or TWRP installed, neither of which I do.
So, can anybody offer their help or suggest something I haven't already tried? Or should I be on EBAY looking for motherboards? Thanks in advance.
Calgary84 said:
Short version of question: How can I unbrick my ONEPLUS 3 (A3000) if I cannot boot to Android and OEM Unlock AND USB Debugging both have not been enabled?
Long version: Phone was recently purchased second hand from a third-party market (Kijiji, kind of like craigslist for Canadians). Person I bought it from claimed in the ad that the device was in a bootloop and couldn't access the OS. I had in the past successfully saved a ONEPLUS 1 from bricked status, so I didn't feel a simple bootloop would pose much of an issue. That, and at the price he was selling I really couldn't turn it down.
I tried various different methods of restoring the phone's partitions, OS, and firmware to stock/custom, but had no real luck with any (I will list below what I have attempted). If there was a root cause of this, I believe it's due to the fact that some part of the phone's storage partition (boot or system if I had to guess) had become corrupted at some point. Given the volume of threads I've seen here and elsewhere online, I wouldn't rule out a bad OTA flash, but doesn't really matter. What does matter, however, is that the Android OS is inaccessible despite my best efforts, and the bootloader is set to locked and ADB Debugging remains off.
Generally speaking, is there a way to access Developer Options to correct both these issues through terminal or a tool? I'm confident that I can get my device working again if I could access this menu, but as of yet I have had no luck.
Methods used to restore/info worth mentioning
While I don't doubt their effectiveness at large, for whatever reason I have yet to find a tool/guide that yields the anticipated results upon completion. MSM Download Tool (V3 and V4) have both been downloaded, executed, and completed numerous times, but will still not boot past the loading screen upon completion.
According to Unified Android Toolkit, my device build is being detected as "OnePlus3 7.0 NRD90M" and All-in-One Toolkit is showing that Android 6.0.1 is installed.
Drivers are all installed correctly, as proven both via tools downloaded and through Windows CMD terminal (adb devices, fastboot devices, adb get-state, etc)
Stock recovery and bootloader modes can both be reached through both hardware keys and software commands. I will note that it seems to take longer than I'd expect to boot to either of these modes using hardware keys.
I have utilized multiple USB ports, Type-C cables, different OS' on two laptops (MS Windows 10 and 7, FWUL Linux). I usually have no problem with the device being detected by the system. When I have, it usually involved one pesky USB cord.
common commands used and their effects:
fastboot OEM unlock: fails, cannot be done remotely
fastboot flash x: fails, remote: flashing partitions not allowed
ADB push: fails. cannot access partition
ADB devices: device is seen by system with serial and state
fastboot devices: device is seen by system with serial
ADB sideload: varying results. Some will fail at 0% citing "total xfer: 0.00x", some will reach 47% and fail (always exactly 47% oddly). Generally if the sideload operation passes 47% it will complete.
fastboot format/erase x: fails, partition formatting/erasing not allowed
fastboot continue: executes, but does not help with android bootloop issue as I had hoped
While I searched for an answer online, I did come across an infosec whitepaper regarding ONEPLUS 3 vulnerabilities, though it was over a year old. To my surprise, the command they had been entering works on my device, but I'm not sure how to properly use it effectively. The command used was fastboot OEM boot_mode [rf/wlan/ftm/normal]. Now, I was unable to determine what each of the triggers does, but what I did discover is that with boot_mode set to rf, my device would display chinese/korean lettering in lieu of the usual ONEPLUS logo with "powered by Android" below. This is also how I managed to have my device show up in CMD terminal for ADB commands to be issued. To the best of my knowledge though, there doesn't seem to be much point to it as I couldn't push/pull any files. Does anybody know where I could find more info on this command, as I'd like to know what the other triggers accomplish.
I've just about exhausted every available resource looking for an answer, but im still coming up short. I've gone as far as contacting ONEPLUS directly, but without proof of purchase they can't (more accurately won't) help me. And while it's not a business practice I would personally support, I can understand why they have it implemented. I've contacted a few phone shops in the area, but none have been able to assist me further than I've already gotten in this process.
I apologize again for creating a new thread about this, but I felt my circumstances warranted a new thread due to the bulk of the others having either an unlocked bootloader or TWRP installed, neither of which I do.
So, can anybody offer their help or suggest something I haven't already tried? Or should I be on EBAY looking for motherboards? Thanks in advance.
Click to expand...
Click to collapse
Thanks for the exhaustive description. You seem to have covered every known method. If the MSM Tool also fails, I think that it is a hardware issue and you are better off searching for a new motherboard instead of wasting further time on trouble-shooting.
Best of luck!
tnsmani said:
Thanks for the exhaustive description. You seem to have covered every known method. If the MSM Tool also fails, I think that it is a hardware issue and you are better off searching for a new motherboard instead of wasting further time on trouble-shooting.
Best of luck!
Click to expand...
Click to collapse
I was afraid of that..... is there a way to test a given hardware component?
Have you tried the unbrick tool FULL updated: https://mega.nz/#!NmhhgZyB!CM7Fw8VjECiMIhh4gRXUx24QVCiE599_ZFAPDf08AiM
acetone802000 said:
Have you tried the unbrick tool FULL updated: https://mega.nz/#!NmhhgZyB!CM7Fw8VjECiMIhh4gRXUx24QVCiE599_ZFAPDf08AiM
Click to expand...
Click to collapse
Indeed I have, dozens of times between the full and mini versions. I've even gone as far as running the toolkits featuring MSMDownloadTool v4.0 to see if it achieved different results (it did not). The mini tool would finish doing its thing (turned the text green upon completion),but I would face varying partitions not being flashed correctly. The full version completes and does not have these varying partitions missing, but the device would then be either stuck in a bootloop where it will eventually reboot itself, or would hang indefinitely on the "swirling dots" loading screen. I tried the remedy of deleting cache in recovery, but this did not help.
deleted
***UPDATE*** - As I mentioned in this thread earlier, I noticed a discrepancy between the variant type listed on my actual device and the variant type returned when queried via fastboot. This got me thinking, and to make a long story somewhat shorter, I found that while most stock Oxygen images I attempt to sideload onto the device fail (at precisely 47%, oddly), I was able to sideload two different Hydrogen images without any resistance at all. I'm guessing something to do with the eMMC vs UFS file storage systems and how each OS uses them.
So I got Hydrogen flashed onto my my device. Smooth sailing, right? Afraid not. Despite fastboot's output clearly stating it was a successful transfer, and the stock recovery on the device echoing this, I still cannot get the OS to load. Now i' stuck with the loading screen hanging indefinitely prior to animation occurring, so basically the static ONEPLUS logo. Factory resets and cache wipes have done nothing to help the situation along. Conventional wisdom from the threads here seem to say using the MSMTool is the right answer..... and thus the circle of frustration is complete with me arriving back where I started. Does anybody have another suggestion I can try out? Still can't flash/boot to TWRP, unlock bootloader, or access Android to activate USB Debug/OEM Unlock either btw.
Have you tried flashing just the firmware, i havent flashed in years but i would assume you could sideload the firmware as well?
voodooline said:
Have you tried flashing just the firmware, i havent flashed in years but i would assume you could sideload the firmware as well?
Click to expand...
Click to collapse
Guess who didn't read? And after a year without flashing + a lack of reading skills, you still think you could solve this case? That's a spirit.
===
You better do pm some devs in dev section and point them to this thread and see if they can help, if you are still curious.
My guess is dead emmc, it can be replaced without buying the whole board.
150208 said:
Guess who didn't read? And after a year without flashing + a lack of reading skills, you still think you could solve this case? That's a spirit.
===
You better do pm some devs in dev section and point them to this thread and see if they can help, if you are still curious.
My guess is dead emmc, it can be replaced without buying the whole board.
Click to expand...
Click to collapse
I did read it, its funny always someone who has to be a **** about things. I should have been more specific. He was able to flash h2os. So he could try to flash the firmware for h2os to see if that gets it to boot.
voodooline said:
I did read it, its funny always someone who has to be a **** about things. I should have been more specific. He was able to flash h2os. So he could try to flash the firmware for h2os to see if that gets it to boot.
Click to expand...
Click to collapse
Magnificent, bro.
You're a truly genius.
Hi all!
Some days ago I urooted my TV android tv box with superSU and then I restarted it. From that moment when I plug the device it only reach the T9 logo (not the android one) and don't go further.
I've tried different ways to try to unstuck it, but nothing has worked.
I tried:
- enter recovery boot by holding the button in the av hole -> nothing happens
- install new firmware with adb sideload with both ubuntu and windows 10 -> always get errors (often error: closed, sometime other errors that at the moment don't remember)
- install new firmware with sd card using SDCard Installer -> the device doesn't boot when the sd is inserted
Moreover, with adb in ubuntu sometimes it recognises the device and I can enter the adb shell (but obtain errors when try any tipe of command), and sometimes don't (after adb devices I see list of attached devices: ??????????????? offline)
Now I'm thinking to try to install an ubuntu like on an usb pendrive...
I will be very grateful of any help/suggestion to how to revive my device :fingers-crossed:
Thank you!!!
Does this happen to be a pendoo model? I have a pendoo x10 MAX and i actually simply just installed supersu while it was rooted. Since then, I haven't gotten this thing to boot. Just stays on the boot screen the entire way. I wiped in recovery, knew that'd do nothing. I just wanted a root MANAGER. I tried Magisk, my favorite.. no go.. so then I went a bit old school.. so I tried ChainFire's SuperSU.. and THAT updated the SU binary! It said it succeeded.. it asked to do recovery install or normal install.. on phones, I've always done normal.. so I chose normal. Plus.. this thing has no custom recovery. I found it on Amazon. Overpriced, but great with the controller it had. It looks like I'll need a replacement and maybe a request to ask this guy if he could possibly NOT use something like KingRoot/KingoRoot/AmaraRoot or ANY One click root tool.. they just cause more bloatware, inciting boot issues and problems within the Android box itself. These One Click Root tools are out of control. It's to the point where I need to find a way in to adb and find the firmware for the latest version of this thing... X10Max from Pendoo.. I have not found a thing anywhere regarding firmware, and their website is ****. NOTHING *anywhere* on these things.. hell I'm about to return it as I bought it for $72. I have another one, same model.. wondering if the root method was different. About to boot that up and find out. I'll even swap the board. At this point.. he rooted it.. the WRONG way.. you can MOUNT THE /SYSTEM PARTITION IN RECOVERY. THIS IS ANDROID 9 we're talking about--the recovery supported by API v3.
This can and should have a TWRP custom recovery. If none exists, don't bother. As long as you can mount /system then you have a chance, at least, to root the damn thing.. which is why I'm still messing with it. I have another two weeks to return it. I'll give it another couple of days before I call it off and just switch out the good board for the bad one, return it, then return the other one and just use it until I find a way to use a custom recovery on this thing. There has to be.. unless there is no firmware available in sight (for an RK3318 or 3328, can't tell.. recovery mode says 3328, model name says RK3318. I see no difference at the moment aside from processor naming at this point--maybe speed?)
I'm still a nub with Android TV boxes so don't hold it against me for updating the damn root binary. If I could find a way to just reinstall the entire firmware and delete all previous stuff, I would. It would be worth it to learn. I would then mount /system in recovery and soldier on.
One little issue with this thing.. there's only one USB port that actually works. Same applies for the same exact product, a replication of the same thing.. was a "replacement" that still have/has the same qualities.
I've ranted enough. I vote more research into RK33xx processors and possible custom recoveries. I'm about to look for it based on only the device itself.
Note: Been stuck at boot screen ever since the binary was updated. I felt it was necessary to have a boot manager. I don't know where to even find the firmware. Can.. anyone point me in any direction? Something that MIGHT work on this thing? Android 6 or 7 would even suffice, return or no return, as "stuck on boot screen" will be my complaint. That's.. the actual complaint. I can't just *flash it* like the old days.. and maybe the original Android 9.0 firmware would suffice.. I don't know, but Pendoo.. wouldn't that be preferred?
You will need an SDcard to recover this box. I think the T9 32GB 4GB rom will do the job since its a cut down version.
Make a update SDcard and pop it in and power on the box. It will start the recovery on its own.
hello, sorry for my English I live in France I would have a question about the box: TV T9 RK3318, 4gb / 64gb. the problem is that the time is desynchronized on restart and creates problems to connect to applications when the time is out of order, I tried everything changed the time zone to deactivate and entered the time Manual it goes out of order all the time . is there a custom version or a version 10?
Very cook did I checked this out awhile back alot of good information that's for your contribution
I recently bought Asus Zenfone, because here in Ukraine is war, so I want small device with Windows (electricity often is off here because rockets fall on our electrric infrastructure etc).
So I've bought Asus Zenfone 2 used (it costed 16,25$). It came without accumulator, and 1/3 screen working. So I went to radio-market to buy new battery, it costed + ~10.25$ + 2,5$ to install battery. Then I've bought new touchscreen for it for ~22,5$, plus payed ~6,25$ to install it. Then around 7,5$ to restore battery connectors (on device and accumulator). So finally it worked, and wanted to see how to install Windows on Zenfone. Sure, if I had possibility to buy anywhere Zenfone better, new, not used, - I'ld do it, but it is not that easily available, just like any other Intel smartphone.
So, I started reading - how to make my device rooted. I don't understand how to get root. I found on wikipedia, that rooting is different from unlocking bootloader, and realized - yes. I need to unlock bootloader, and to boot from external flash-disk and install windows, or at least - new kernel with KVM support. I used pn my Android (non intel) Limbo x86 emulator, it can run some old windows 98 etc, maybe even xp, never win 2000, and if it runs win-7 or win-8 - it is so terribly slow. So I decided to buy Asus Zenfone. As in KVM mode I can send commands to CPU directly, and hope this Windows works much faster than in emulator. I hope just at least to run Windows XP on it, I need to code some C# code, so that Andorid phone is not only for mp3-playing, internet on the go and make calls, but to learn, study and to work. I don't know why Microsot, Intel and other companies don't like Intel CPUs in mobiles. They could do it if they wanted. I like WIndows because most programs are for Windows. And I want desktop x86 windows also on every mobile, intead of all Androids.
Anyway, What I tried to with my Zenfone. I found one amazing experience - that our hero and inspirer (ley God blesses him, maybe he will work in Intel/AMD/Asus/Microsoft etc to make more newer KVM kernels for future x86 phones with windows) - so Ycavan made KVM for Asus Zenfone 2. Great, I've read his thread - https://forum.xda-developers.com/t/...0-with-kvm-bridge-compiled-need-help.3145055/ - completely, with pen and paper writing down important information, downloaded all the files, and decided to start flashing.
I copied them to root of my Zenfone, unpacked tars and converted them into ZIPs. I also unpacked .img files to root of phone (I mean its folder which is visible if I connect it thorught USB, I know it is not "/" root of file system of Andoird, but anyway it is visible even inside CWM... sorry, was visible)...
So, I made some mistakes. I downloaded the kernel, tried to flash it using commands like :
fastboot flash boot boot_fhd_2.19_kvm_bridge_20150710.img
fastboot flash boot boot_fhd_2.19_kvm_bridge_20150714.img
fastboot flash boot boot_fhd_2.19_kvm_bridge_20150717.img
fastboot flash boot boot_fhd_2.20_kvm_bridge_20150820.img
fastboot flash boot boot_2.19_kvm_bridge.img
fastboot flash boot boot_fhd_2.20_kvm_bridge_20150820.img
but non of them produced bootable Zenfone. So I had to revert to previous bootloader using the CWM tool.
In fact I liked this CWM most. I found this thread - https://forum.xda-developers.com/t/...root-ze500-ze550-ze551-temporary-cwm.3114063/
or similar here on forum, and it worked amazingly. I attached Zen-phone to USB, turned it off, then on while pressing, keeping pressed volume-up key, and after Asus logo appeared and some "zzz" vibration, again it blinked and I saw bootloader with Android robot, and possibility to scroll through menu using volume up-down, to choose normal boot, or reboot/power off, or to run restore etc.
For some reason, Restore there not worked. So anyway, I understood that I can use tool like ADB (Android debug bridge) and fastboot to copy new firmwares/kernels/bootloaders etc to it, so I guessed I can do it myself, and was ready for risks... And this what bad can happen - it happened.
So, I runned in CWM - file cai_dat_CWM.bat - which asked to type ACCEPT and then T4, and phone started to go into amazing mode, some "clouds" started appearing on phone, and it loaded into special secret menu, from which I could select what to do next. To me it looked like default boot manager which I wanted to see like in Dos/Windows machines - so I can choose to run into safe mode windows, or set some settings before booting, or even use "reanimator dvd" etc to load Windows and other tools to do partitioning, passwrods recovery etc. So it looked like on desktops, and very nice. I went inside the menu, and found good option to make backup. I did it all. Then in same CWM tool (I think it is called SuperSU for Android), I finally choose to restore bootloader/kernel/boot (custom recovery), and this saved my from bricking the first time after I followed the manual from Ycavan. Well, I know I can read a lot more threads how to do this and that, but there is always risk that something wrong can happen. So I tried to read as much as I could, and follow manuals as precisely as I could understand. But my phone is kind of "bricked".
Now it shows some scfreen like TV which can't catch any tv program. So it is some random colors - see attached picture. It is good that it shows at least this. But in worse situation - it doesn't show anything. So let me tell how I achieved this, and if you can tell me how to avoid this mistake and to recover it. I hope to get help from anyone here who installed KVM kernel(s) and acheieved running Windows on their zenfone 2 (or maybe anyone who has XPerience with other x86 phones may help, or if it is general issue how to unbrick - then also non x86 users please help).
So, CWM made backup, I became more non-scared to make more experiments with firmware. But main problem is that I don't know which firmware to use. I ideally suggested that when I change kernel to KVM-supported from Ycavan - that it will work with my Andorid 5.0 (it was installed when I bought it). So, but unfortunately, after installing any of KVM kernels of Ycavan - I was unable to understand which OS to install, which version. So even I tried to try to flash whole 1GB+ image (I have downloaded UL-Z00A-WW-2.20.40.59-user.zip from official asus.com - https://www.asus.com/ua-ua/supportonly/asus zenfone 2 (ze551ml)/helpdesk_bios/ - but. I was unable to upload it to zenfone (flash it), as it said it is older than installed version.
Anyway, now it doesn't matter as I cannot run into ANdroid at all. Worse - I cannot even get Bootloader working in Android, as I see after turning phone on - only "white screen" with non-working TV-like image (see attached picture of my Zenfone 2).
So, to make this happen, I did this: I found some information about TWRP. I tried to install as recovery tool. Even though it was flashed into mobile, and I installed it from apk from Google-Play, still, I was unable to run it... So then I found even cooler tool - which was too risky to install. I was good, but Andorid stopped running at all.
This tool is called - preroot601. I runned in it preroot.bat, and then it did something similar to CWM, but several times it restartd the phone _ i have added screenshots of how it looked like on PC / Windows. So after several restarts, it did a lot of changes - Android didn't start after it. Phone always was able to start into recovery mode - into TWRP (I downloaded its .img and flased it as recovery for phone). But in TWRP I think I did something wrong. I made backup of all files (syste,, bootloader, everything). I saw it is cool - to see there terminal, ability so set attributes for files, mount partitions ... even USB -hey, can I run from flash-disk? or from external DVD/Bluray which I have in this mode? I have USB-hub, and can connect to it keyboard, mouse, flash-usb, ssd/hdd - all through Microusb-usb adapter and to usb-hub. So what I wanted to do is to try to see flash-disk, mount it on my android zenfone. And then after restart - I had black screen or this 'non-working analog-TV screen when no program/channel/wave is caught for signal"...
So, I don't even understand what I did, and why this all happened, and why I have to do to restore bootloader at least.
My aim is to have KVM enabled in the kernel. I don't mind if it is old Windows like XP working on this Zenfone, but I like windows to be my main OS on every phone which I may use in future (and hope they all be x86-64 and not ARM). So as I don't have Steamdect now (it has also AMD x86 CPU, like Zenfone), I want to do this, achieve it - having Windows on mobile - Zenfone.
I can carry it in pocket everywhere, so why not people like having desktop Windows x86-64 in each and every mobile? Even Lenovo are collaborating with IBM - then why not make also IBM-Mobile / IBM-smartphone, which will also be as good as PC - to unassemble it, change any part like on desktop, why not do it? I think everyone will enjoy it, and it will boost everything to better hights, levels.
So, please. If anyone here has similar experience of going to same screen like I have (see screenshot), or like that - black screen - indeed my device also may not even show any thing - even no ASUS logo, no bootloader (even if I press Volume-UP after powering and after flash it usually showed bootloader with robot - no... not now)...
So I don't see anything on screen of Android Zenfone now. no text, no bootloader, no recovery even - no TWRP menu. I think I am ready to format whole zenfone, and install there maybe some partition manager (like you know there is Partition magic on PCs, when I can split HDD/SSD nto two parts, one for Windows, and say other for Unix - Ubuntu or Android x 86 - all on same physical drive)... So I want some re-partitioning for intern SD memory, and be able to install there some ISOs, say with DOS, Win3.11, win 95, 98, 2000, xp, 7, 8,1 and maybe even 10. But guess last will be slow. I think Windows XP would be ideal OS for my Zenfone, if it can run fast. Win 7/8 maybe will be slow. But for some sceintific aims - like I just write some algorythm in Visual studio, and can do it even in WinXP, so why don't do it on my Zenfone? I don't like many Andorids, as they are not for work much - they are used by many people to play games, watch videos on phones, surf social networks, but not for real work. Real work is usually on WIndows, and no laptop can replace "Windows x86 in pocket" (on mobile). And I wonder why Microsoft develops "Windows for ARM" instead of investing millions into efforts like which Ycavan did - to make Windows run in KVM mode fast on x86 smartphones.
Ok, So, any ideas? What should I do now? I need some special tool to fix my phone first. Fix its loader. I think I need to bypass fastboot.exe restriction, which shows "waiting for device". Command in cmd like this: ADB.exe devices -L --- shows device from time to time - it shows:
c:\adb>adb devices -l
List of devices attached
0123456789ABCDEF device
c:\adb>fastboot flash boot boot_2.19_kvm_bridge.img
< waiting for device >
So, I cannot even flash some recovery device in this way. In devices manager I see "ADB interface" in "USB devices" category in devices treeview. And sometimes Moorefield appears, but with exclaimation mark - I have no idea how to make it disappear. I found here some info that I can install tool - xFSTK_Downloader_v1.7.0.zip - I downloaded it, installe,d but it doesn't run (I have win10 x64bit). hm... And driver required - iSOC_USB_Driver_Setup_v1.2.0.zip - I installed - but nothing.
So, what to do? How to make bootloader appear again? And how to write there prob=per bootloader with KVM kernel, and which firmware to flash so I can use KVM fast there with fast Windows...? Is it possible at all to make it run WIndows natively on Zenfone? or it will always be only in virtual machine inside some ArchLinux or in Limbo x86 on Android?
I read that Ycavan used this ArchLinux, but I don't understand why. Is he installing it over Android? Then also which version he uses? I need to know each and every version whcih he uses to make everything works. I 'ld require all the firmwares which he uses to make it work also - to make some Windows iso run on my Zenfone 2.
Did anyone achieved this successfully, except for Ycavan - to run Windows on Zenfone? Or except for him noone was able to install KVM kernel, and it was similar to mine situation? And maybe this is the reason why manufacturers of phons don't like x86 phones? I don't know. Any ideas?
See screenshots. What to do in this state?
IF anyone can please upload to somewhere whole pack of files ("WIndows on Zenfone starter kit") to make anyone able to just follow instaructions which will work in all cases to install WIndows there like Ycavan has - it would be great. There is lack of more detailed information - which .img files, .zips, firmwares etc, which OSes are supported by Ycavan's KVM kernels?
I have no idea. if anyone passed this path, and achieved Windows on Zenfone, please share your experiences, Ireally need it. Here in Ukraine when electricity disappears almost daily, we need devices like x86 phones almost for everyone. And mo matter if Windows is a bit old. KVM mode I guess must be much faster, almost native speed, so (like on tablet PCs), so please help...
Thank you all in advance, whoever will answer me.
indubhushan said:
c:\adb>adb devices -l
List of devices attached
0123456789ABCDEF device
c:\adb>fastboot flash boot boot_2.19_kvm_bridge.img
< waiting for device >
Click to expand...
Click to collapse
wrong mode. adb is only working in
- normal/boot mode
- recovery mode
fastboot is only working in
- bootloader mode
- fastboot mode
You can see 0123456789ABCDEF device in adb devices, therefore you are either in TWRP or in Android (Win?)
type adb shell and check the prompt is either $ (shell) or # (root shell)
in root shell you can flash partitions from cmd line. you can also reboot into bootloader/fastboot mode from cmd line.
Code:
adb reboot bootloader
I had success in restoring my bootloader (logo with android robot) - I intalled xFSTK, so somehow I had success to make it run, and I added threee files (1, 2, and 4th) and tried to flash it. Phone was visible as Moorefield. Then I tried to use Asus flash tool to flash big RAW image, but for some reason I don't know why - I had even whole day left it to flash, it didn't do the task - Android stopped booting - no logo showing at all - have to use xFSTK to recover. Maybe I use wrong RAW image (from official site it is .zip, so have no idea where to get those raw files).
When try to flash using flashboot - I get error: - flash cmd error.
As for devices list. My device rarely appear there. It may appear for some seconds, and then xfstk can have success to flash it, and maybe even make it runnable into Android robot scren (bootloader).
I am thinking that I need to install maybe ArchLinux, which Ycavan is using, but have no idea where to get RAW file for it, and how to flash it. Maybe some problem with my USB port on old laptop, or maybe even with USB cable (though have few good almost new cables, even new 4Amperes one). So maybe even problem in port of Zenfone itself (to change it). No idea. Because even when I tried to flash it (that huge 1GB file), phone disconnected, or showed "ready for commands", instead of showing process of ownloading RAW image/Android into phone's memory.
Flashboot/adb almost unusable. Well, I'll try, maybe it'll work.
My hope is try to go into CWM, run from it into "secret menu" on phone, and from it - to access internal memory of phone, and restore phone from backup. But when I tried to load into it once - it hanged on "clouds". I don't know...
And I don't think I'm ready now to format internal memory of phone or to repartition. At least I don't have backup on some external card (sd-card) etc.
as for adb. maybe it can't see my device, even if it is "recovery mode" (when see in devices manager in Windows - Moorefield). Now I'm stuck on xFSTK and can't go anywhere further like adding TWRP into phone, or foing into backup/restore menu on phone, and of course there is no Android. Even when I see Android robot (boot menu) - I feel happy, that at least phone shows anything, so at least bootloader workds. Maybe difference is in drivers - when I have Moorefield driver, then maybe it contradicts with Zenfone driver, and I have to reinstall them? Or use other OS? I have dual-boot (two Windowses on my laptop), so maybe I need to use one Windows - to work with Moorefield (xfstk) - when phone is in "worst" situation when no logo shows / no bootloader. And the other Windows I have to run on laptop - with Zenfone driver installed (I think it shows something like Asus device in device manager). But they seem to use contradicting drivers, I am not sure. And maybe it's some problem with my usb ports, but hope no. They seem to be ok... Maybe I'll have to go some day to give phone for diagnostics to repairing center again ;-(