Develop Bugs

CDMA???!!!

I've googled for hours for this. I am looking to get the MSL/'unlock code'/SPC for my CDMA blueangel. I have not found the answer anywhere. Does anyone have any pointers for me in unlocking an HTC CDMA phone?
Any help will be SO greatly appreciated.

You can use this app (you need to run the 2003 version of the .exe). It will take your ESN HEX as input (use capital letters) and will produce your MSL (not OTKSL). This app works for all HTC CDMA phones--Harrier (CDMA Blue Angel), Apache, and Titan).
It was created by a guy named isosdcftp over at ppcgeeks.com. Here is a link to the thread in case you're interested (primarily concerns the titan/mogul though):
http://forum.ppcgeeks.com/showthread.php?t=5531
Also keep in mind some carriers use 000000 for the MSL. If neither that nor the code produced by GetSPC work, then perhaps the particular carrier who sold your phone used their own MSL algorithm (possible but unlikely).

doesnt work.. I'm with telecom new zealand if that's any help

Can you be more specific? Does the app run and produce an invalid MSL or can you not even get the app to run? If you want to PM me with your ESN HEX I will generate it on my end and PM it back to you to confirm.
I have a Sprint-branded Harrier (I'm in the US) and GetSPC spit out the correct MSL for me, but maybe TNZ programs in their own MSL instead of using the HTC default. In that case not much you can do unless you get the phone into DIAG mode and see if bitpim can read it.

Sorry man. It generates a MSL, but when I go into the pst (##778+talk) I enter it and it barks at me 'Your unlock code is not correct!'. I will pm you with my ESN.
And how would I put it into diag mode? I am fluent with bitpim and linux etc. but I can't figure out how to put it in diag mode.
If there's any more help from anyone it would be VERY greatly appreciated.

tatotato said:
Sorry man. It generates a MSL, but when I go into the pst (##778+talk) I enter it and it barks at me 'Your unlock code is not correct!'. I will pm you with my ESN.
And how would I put it into diag mode? I am fluent with bitpim and linux etc. but I can't figure out how to put it in diag mode.
If there's any more help from anyone it would be VERY greatly appreciated.
Click to expand...
Click to collapse
put the phone in diag mode ##DIAG send or ##3424 + send, then instal serial driver for the new hardware, you can google for the driver, then check the modem com port under modem in Device manager, and set the same com port for Bitpim using other CDMA phones, then check in NVM 000 or 001 and you should see the 6 digits SPC or once you know the virtual serial allocated to modem you may use other tools to check spc
Lets see how it goes,..
bR

doesn't work, when I go ##DIAG+talk it just calls the number.

please help to unlock my zte ev-do modern s/n 412823812444
am getting phone does not accept spc in cdma workshop thanks.

PC can't recognize Epic as mass storage after prl update (attempt)

So, I tried to do the manual PRL update in this thread , but even after uninstalling QTSP my phone only charges.
I can enable mass storage on the phone, but it doesn't register in Windows. I've tried going into disk management too, but there's no drive to assign a letter to.
I'm running Win 7 x64.
Any help is appreciated.
PS I have the Samsung Modem and Ports showing up in device manager. I don't know if this is normal.

Try:
1.Changing USB cable/port
2.Rebooting the computer/phone
3. Reinstalling the Samsung USB drivers.

I actually did all those things Xobx. I should've mentioned that!

lattiboy said:
So, I tried to do the manual PRL update in this thread , but even after uninstalling QTSP my phone only charges.
I can enable mass storage on the phone, but it doesn't register in Windows. I've tried going into disk management too, but there's no drive to assign a letter to.
I'm running Win 7 x64.
Any help is appreciated.
PS I have the Samsung Modem and Ports showing up in device manager. I don't know if this is normal.
Click to expand...
Click to collapse
Did you set it back to PDA from modem once the flash was done?
-uncut and uncensored from my Samsung Epic 4G

lafronz said:
Did you set it back to PDA from modem once the flash was done?
-uncut and uncensored from my Samsung Epic 4G
Click to expand...
Click to collapse
I never actually DID the flash. That's the weird thing. I installed the software, got the files, and decided it wasn't worth the trouble. No idea what to do now......

EDIT: Did you ever flip USB back to PDA in the hidden menu? If not, do that first, because it's your problem!
Does USB work in Download Mode?
If not, you're probably facing the same USB bug I encountered when trying an update. Samsung's got some poorly-written software in their USB stack. I posted a possible solution here, but if that doesn't work, you're pretty screwed. If you're non-stock, flash back to all stock (recovery, kernel, ROM) and go exchange your defective device.

k0nane said:
EDIT: Did you ever flip USB back to PDA in the hidden menu? If not, do that first, because it's your problem!
Does USB work in Download Mode?
If not, you're probably facing the same USB bug I encountered when trying an update. Samsung's got some poorly-written software in their USB stack. I posted a possible solution here, but if that doesn't work, you're pretty screwed. If you're non-stock, flash back to all stock (recovery, kernel, ROM) and go exchange your defective device.
Click to expand...
Click to collapse
Okay, I hate to plead ignorance, but what "hidden menu" are we talking about?
I'm running Midnight Rom 5.2 journaling off, btw.
thanks!

In the manual prl update thread it gives you a code to enter into the dialer to change it to modem mode for connecting to qpst. Verify both settings say PDA.
EDIT: The code is ##8778# in dialer. It should ask for MSL unless you changed it to 000000 in qpst like I did
If you don't have your msl, download terminal emulator from market and type this at the dollar sign prompt: "getprop ril.MSL"
Without the quotes, case-sensitive.
That six digit code is your MSL. Let me know what the settings show.
-uncut and uncensored from my Samsung Epic 4G

lafronz said:
in the manual prl update thread it gives you a code to enter into the dialer to change it to modem mode for connecting to qpst. Verify both settings say pda.
Edit: The code is ##8778# in dialer. It should ask for msl unless you changed it to 000000 in qpst like i did
if you don't have your msl, download terminal emulator from market and type this at the dollar sign prompt: "getprop ril.msl"
without the quotes, case-sensitive.
That six digit code is your msl. Let me know what the settings show.
-uncut and uncensored from my samsung epic 4g
Click to expand...
Click to collapse
thank you! Worked!

lattiboy said:
thank you! Worked!
Click to expand...
Click to collapse
You're welcome. Glad I could help.
-uncut and uncensored from my Samsung Epic 4G

meid locations for baseband 2.15.00.0808

I need the meid locations for basband 2.15.00.0808. I don't uderstand the winhex way how you have the offset and have to add this to that. Thanks

jcthelight said:
I need the meid locations for basband 2.15.00.0808. I don't uderstand the winhex way how you have the offset and have to add this to that. Thanks
Click to expand...
Click to collapse
I think you forgot your flamesuit

fenixjn said:
I think you forgot your flamesuit
Click to expand...
Click to collapse
What do you mean?

jcthelight said:
I need the meid locations for basband 2.15.00.0808. I don't uderstand the winhex way how you have the offset and have to add this to that. Thanks
Click to expand...
Click to collapse
Hey man I just woke up with a super hangover.. once I can stare at my laptop w/out the feeling of death coming over me ill be more then glad to help haha.. what stage are you at in meid retreival?.. (let's try and stay away from any meid mod talk.. retreival- cool, mod- no bueno)
Sent from my Random, old but still kickin, Epic 4g

j7jman said:
Hey man I just woke up with a super hangover.. once I can stare at my laptop w/out the feeling of death coming over me ill be more then glad to help haha.. what stage are you at in meid retreival?.. (let's try and stay away from any meid mod talk.. retreival- cool, mod- no bueno)
Sent from my Random, old but still kickin, Epic 4g
Click to expand...
Click to collapse
The esn is done. I just just need addresses for meid retreival. Would you rather pm? Thanks. I was at work when you responded.

How To Calculate your meid or esn addresses using Winhex
jcthelight said:
The esn is done. I just just need addresses for meid retreival. Would you rather pm? Thanks. I was at work when you responded.
Click to expand...
Click to collapse
its cool.. I dont know the addresses for your radio, but I can help you find them heres some steps you can take to help you calculate the address:
After you open your scan results with winhex
-do a search for your meid in reverse, with no spaces. Make sure you check the "list search hits" box. It should list the locations of the results at the top.
-there's gonna be an offset number to the left of it, you can click on it and it changes, click it so it shows the an offset number that contains letters.
-Open up the windows calculator and make sure it's in "HEX" mode.. it usually starts up in "DEC" mode.
- If you did a searched, lets say "00FA-0000" for example, in cdma ws, your gonna want to take your offset number and add it to your original search location.. for example 00FA0000 with no dash.
-You'll come up with a result like this-
*example- 00FA0000+4EDC2C= 148DC2C which would be 0x0148DC2C
-Just add 0x0 or 0x00 (depending on the length of your result number) in front of it.
-Do this for all the other locations & there you go, you have your addresses
I hope that helps

j7jman said:
its cool.. I dont know the addresses for your radio, but I can help you find them heres some steps you can take to help you calculate the address:
After you open your scan results with winhex
-do a search for your meid in reverse, with no spaces. Make sure you check the "list search hits" box. It should list the locations of the results at the top.
-there's gonna be an offset number to the left of it, you can click on it and it changes, click it so it shows the an offset number that contains letters.
-Open up the windows calculator and make sure it's in "HEX" mode.. it usually starts up in "DEC" mode.
- If you did a searched, lets say "00FA-0000" for example, in cdma ws, your gonna want to take your offset number and add it to your original search location.. for example 00FA0000 with no dash.
-You'll come up with a result like this-
*example- 00FA0000+4EDC2C= 148DC2C which would be 0x0148DC2C
-Just add 0x0 or 0x00 (depending on the length of your result number) in front of it.
-Do this for all the other locations & there you go, you have your addresses
I hope that helps
Click to expand...
Click to collapse
Says 0 found.

jcthelight said:
Says 0 found.
Click to expand...
Click to collapse
did you click the binoculars with "hex" below them.. because you have to click the ones w/out "hex" below them.. meaning your not supposed to search for specifically hex values

j7jman said:
did you click the binoculars with "hex" below them.. Because you have to click the ones w/out "hex" below them.. Meaning your not supposed to search for specifically hex values
Click to expand...
Click to collapse
so search for text it says search at the top then search for hex or text values. i tried both and got nothing.

00FB:55AC
00FD:6968
00FE:1524
015F:0F2C
015F:0F38
017C:AED0
018F:31AC
0190:3438
01D6:6D47
01D8:06C1
Baseband 2.15.00.0808
Software 4.53.651.1

I need one more. meid locations for baseband 2.15.00.0808
-----------------------------------------------------------------------------
meid
0x01D6D444
0x00FB55AC
0x00FD6968
0x00FE1524
0x015F0F2C (2X)
0x015F0F38
0x01903438
0x01D66D47
0x01D806C1
0X017CAED0
0X018F31AC
0X1903438
0x017CAE7C
esn
0x017A0FA4
0x01D5F0F0
0x01D5FC49
0x01D6A4C3
0x017CAA1C
0x017CAE7C (2X)
0x017D1338
0x0188E6BC
0x0127ECCC
0x0157ED2F
0x0157ED62
0x015FBD48
0X00FE681C
0x00FD3DC8
0x00FD3DC8

cheers
0x01d6b701

I dont understand what I must be missing. I have the ESN fixed and as well only missing the MEID. When I scan I only find three locations. I have found others with web searching but still missing some. What REALLY stumps me is from what I can tell I have the exact same set up as the original poster but have NONE of the same ESN or MEID locations. Someone PLEASE point me to what I am missing This is what I have posted below:
MEID:
0x00FD:6960
0x00FB:55AA
0x00FE:1524
0x00FE:1520
0x015F:0F2C
0x0190:3438
0X017C:AED0
0X018F:31AC
Phone Details:
OS - 2.3.3
SW Version - 4.53.651.1
Radio Version - 2.15.00.0808
PRL - 33789
PRI Version - 2.15_009

does anyone have anymore meid locations for 2.15.00.0808?

havieri23 said:
does anyone have anymore meid locations for 2.15.00.0808?
Click to expand...
Click to collapse
Just use the method for the EVO 3d it works great and in 5 mins.
Sent From My HTC EVO On Boostmobile

jcthelight said:
Just use the method for the EVO 3d it works great and in 5 mins.
Sent From My HTC EVO On Boostmobile
Click to expand...
Click to collapse
keep getting "error 222: invalid argument" when trying to copy file 0 and 1943 from nvm directory from phone to desktop

I have another EVO I put on boost no problem... But the usb port broke and screen got smashed... I got another one with the new 2.3.3 gb which I just flashed swag on on it. I have bandbase 2.15.00.0808 with the esn zeroed. But having problems with the meid... I tried to downgrade bandbase to 2.15.00.15.11 and 2.15.00.09.01 but still having problems zeroing and can't downgrade any further to do qmat. I have done a scan and search for meid location but when I enter the location the meid appears to the right of the screen but not where I can edit the hex. I am about strung on this for the last 3 days so any help or advice will be greatly appreciated. I don't have internet at home so if someone could talk me through this over the phone would be great. I have cws 2.7 qpst and qxdm. Or if someone could give the locations other than listed above. Thank you and I am willing to donate once my EVO is on boost.
Hardware 0004
Android bedding 2.3.3
Bandbase 2.15.00.0808
Software 4.54.651

havieri23 said:
keep getting "error 222: invalid argument" when trying to copy file 0 and 1943 from nvm directory from phone to desktop
Click to expand...
Click to collapse
Make sure the overwrite box is checked.

robskilz said:
I have another EVO I put on boost no problem... But the usb port broke and screen got smashed... I got another one with the new 2.3.3 gb which I just flashed swag on on it. I have bandbase 2.15.00.0808 with the esn zeroed. But having problems with the meid... I tried to downgrade bandbase to 2.15.00.15.11 and 2.15.00.09.01 but still having problems zeroing and can't downgrade any further to do qmat. I have done a scan and search for meid location but when I enter the location the meid appears to the right of the screen but not where I can edit the hex. I am about strung on this for the last 3 days so any help or advice will be greatly appreciated. I don't have internet at home so if someone could talk me through this over the phone would be great. I have cws 2.7 qpst and qxdm. Or if someone could give the locations other than listed above. Thank you and I am willing to donate once my EVO is on boost.
Hardware 0004
Android bedding 2.3.3
Bandbase 2.15.00.0808
Software 4.54.651
Click to expand...
Click to collapse
Use the EVO 3D method works great.

Unbelievable how easy that was.... Way easier then my last one.... Thanks a lot.... Now to call and get this error 16 taken care of
---------- Post added at 05:22 AM ---------- Previous post was at 05:16 AM ----------
havieri23 said:
keep getting "error 222: invalid argument" when trying to copy file 0 and 1943 from nvm directory from phone to desktop
Click to expand...
Click to collapse
I had the same problem when copying from the phone just grab the file and drop it on your desktop. But when you go to put the edited file back on the phone use the copy from pc option

Kyocera DuraXT e4277 DIAG Mode??

Hi,
How do I get into the diag mode of this phone? I googled and googled until I could search no more!!
I tried ##diag# and some other codes but none is giving me the option.
I need to be able to connect the phone to the PC and see it in DFS, CDMA, QPST. None of these see the phone usb port now.
Please help. Thank you!
Sprint Kyocera DuraXT E4277

Well, I figured it out!
After all this headache of looking for the DIAG menu on the DuraXT.. It turns out that its not needed.. all I had to do is install the drivers on PC and connect USB cable.. Select Modem on phone and DFS was able to read it.
Now I am another problem.. I need the 16 digit device password and the only thing I see on google is that its all F's (FFFFFFFFFFFFFFF) but that is not correct.

Does anyone know how to find the SPC/MSL for the DuraXT E4277? The memory is unreadable, completely locked from reading.

Mr. Q 5 said:
Well, I figured it out!
After all this headache of looking for the DIAG menu on the DuraXT.. It turns out that its not needed.. all I had to do is install the drivers on PC and connect USB cable.. Select Modem on phone and DFS was able to read it.
Now I am another problem.. I need the 16 digit device password and the only thing I see on google is that its all F's (FFFFFFFFFFFFFFF) but that is not correct.
Click to expand...
Click to collapse
thelastemperor24 said:
Does anyone know how to find the SPC/MSL for the DuraXT E4277? The memory is unreadable, completely locked from reading.
Click to expand...
Click to collapse
Unfortunately Kyocera phones do not use 16 digit passwords, only Samsungs do. If you're trying to repair the esn/imei or unlock it, don't even waste your time, there are no specialized tools available for those tasks, other than reading the user lock, nam, etc via DFS/CWS or other similar cdma tools. But you'll probably need the SPC/MSL which may be gotten from Sprint by pretending that you need the code to factory reset it through the ##786# menu. Kyocera phones have always had elusive security, including full memory lock. Just chalk it up as a "No Can Do"

Qpst lg v30 h932

Hey
I want to run QPST and my phone is detected in the COM in device manager (also at the top of device manager).
But when i add the port in QPST it detects 'No phone' but i can still add the port.
Making a backup etc in QPST doesn't work because of this.
Anyone with more knowledge who knows what i have to do?
I installed the universal LG drivers en did the commands (adb shell, su and setprop sys.usb.config diag,adb).
Thanks in advance!
The 3 images are screenshots of the windows.

Update
I got to the part were you can enter your IMEI but the phone couldn't write the IMEI.
THere was a long eroor message and this was part of it: 'reason other than nvm was full'

Hi, disconnect internet, turn off all security like firewall and virus checker and try again.
youtube video shows device like image attached.
Otherwise no idea

MrParis2 said:
I got to the part were you can enter your IMEI but the phone couldn't write the IMEI.
THere was a long eroor message and this was part of it: 'reason other than nvm was full'
Click to expand...
Click to collapse
I have the same problem, I'm stuck on that error message when trying to repair IMEI on my LG V30 US998, did you find any solution?

Hierwend said:
I have the same problem, I'm stuck on that error message when trying to repair IMEI on my LG V30 US998, did you find any solution?
Click to expand...
Click to collapse
Hey guys, I hate to be the bearer of bad news but even for legitimate purposes, people really hate when you talk about repairing IMEIs here. It's questionably illegal even if you're "repairing" it. If you're cloning it, it's super federally illegal.
I'd word it in a way of "halp, somehow I zeroed my IMEI and I need to write back the exact same IMEI and definitely not some other IMEI on a phone I have because I bought a bad IMEI phone on eBay". Even then I think mods would raise a stink.

Hierwend said:
I have the same problem, I'm stuck on that error message when trying to repair IMEI on my LG V30 US998, did you find any solution?
Click to expand...
Click to collapse
Nope