Develop Bugs

Screen protector aghh lol

Hi when I first got my nexus she looked lovely..screen protector was on...no bubbles nothing
Flip to today I've gone through two and they look crap
Any tips lol
Sent from my Galaxy Nexus using xda premium

arknailed7754 said:
Hi when I first got my nexus she looked lovely..screen protector was on...no bubbles nothing
Flip to today I've gone through two and they look crap
Any tips lol
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Quality seen protectors. I'm personally a fan of xoskins, best on the market imo
Sent from my Sprint Galaxy Nexus CDMA using xda premium

Tip of getting them up good...
Run a hot shower in your bathroom and steam up the room. The steam will remove all the dust particles in the air which is the cause for bubbles that cannot be removed.
Then apply the protector. I usually pull just the back off a little at the top. Line it up and scroll down with a credit card to the bottom. If you still have bubbles just work them out pushing them to the side, top or bottom of the device. As long as there is no dirt or dust under the skin you will be able to get rid of them.
I always use the dry application protectors. I find that they always leave a weird film on the screen. You can really see what I am talking about when you remove one of these from you phone.

Some might say a tip would be to not use one.

SefEXE said:
Some might say a tip would be to not use one.
Click to expand...
Click to collapse
Some might reply to that tip and say they should read about what happens to unprotected screens.

Put it on outside you wont get dust under it.

While I did just start another thread complaining about ZAGG type screen/body protectors I will admit that certain ones offer excellent screen protection. Extreme Guard can be had on Ebay for about $5 for most phones, Nexus included and they're awesome. Very low smudge, and fingerprints. They're cut well and despite the pain of wet install screen protectors they are much easier to install than body protectors. I would recommend them.
Sent from my Galaxy Nexus using xda premium

[email protected] said:
Some might reply to that tip and say they should read about what happens to unprotected screens.
Click to expand...
Click to collapse
Do tell.
What happens to unprotected screens? I've had my Nexus since Jan. with no screen protector. It attracts finger prints but that's not a problem when you have micro fiber cloth (or your pant leg).
I'm not damage prone so to each his own, I guess.
Sent from the future.

Tried the steam method etc.worked a treat. No bubbles.didn't do the shower though waste water lol.was having a coffee so held it a metre above the kettle and it worked fine. Only for 5 seconds or so ..don't want to damage her!
Sent from my Galaxy Nexus using xda premium

Or get a reusable screen protector.
I had the Boxwave one, i'm able to remove dust by using some tape and time.

Realook screen protectors. They're awesome. I have them on my Rezound, and they'll definitely be on the nexus when I get it too. I went to Florida the other day, had my phone in a bag on the beach, and of course sand gets everywhere, and scraped up the screen protector pretty good. Not a single mark on the actual screen though. Plus it feels almost exactly like the glass on the phone.
Sent from my Sense 4 Rezound

No screen protector is perfect so far. The only two I'd recommend are XO, and Martin Fields. XO is a wet application with a rubbery feeling. You might be irritated with the feeling, if so get Martin Fields. Martin Fields are dry app and matte finished, however it conducts fingerprint and oil like magnets. I went with Martin Fields.

Where abouts are you in the UK?
I have an unwanted XOSkin screen protector for the GNex. Its the one that goes to the screen edge.
Ill sell it for the price they are selling it for.. You save on postage... although if your too far away then nevermind

How much are they?
Sent from my Galaxy Nexus using xda premium

SovereigN7 said:
No screen protector is perfect so far. The only two I'd recommend are XO, and Martin Fields. XO is a wet application with a rubbery feeling. You might be irritated with the feeling, if so get Martin Fields. Martin Fields are dry app and matte finished, however it conducts fingerprint and oil like magnets. I went with Martin Fields.
Click to expand...
Click to collapse
My martin fields is a glossy finish, didn't know they had two different versions.
I would say Martin Fields has the best fit and finish. I have always had better luck with the dry application protectors. The wet applied ones always have a strange uneven surface that always looks like crap.
Sent from my Galaxy Nexus using Tapatalk 2

[email protected] said:
Some might reply to that tip and say they should read about what happens to unprotected screens.
Click to expand...
Click to collapse
I've actually had one on there, just removed it recently.
I don't care either way really. Pretty careful with it, but I don't mind the extra protection.

I just ordered an XO off their site for about $11 shipped. The have a promo code 40FDOFF, I think that's what it was lol
Sent from my Galaxy Nexus using xda premium

JDFlint said:
I just ordered an XO off their site for about $11 shipped. The have a promo code 40FDOFF, I think that's what it was lol
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
there is a 50% off code, check the thread. comes to a little under $10.

[email protected] said:
Tip of getting them up good...
Run a hot shower in your bathroom and steam up the room. The steam will remove all the dust particles in the air which is the cause for bubbles that cannot be removed.
Then apply the protector. I usually pull just the back off a little at the top. Line it up and scroll down with a credit card to the bottom. If you still have bubbles just work them out pushing them to the side, top or bottom of the device. As long as there is no dirt or dust under the skin you will be able to get rid of them.
I always use the dry application protectors. I find that they always leave a weird film on the screen. You can really see what I am talking about when you remove one of these from you phone.
Click to expand...
Click to collapse
This is the right way to do it.
The static from what you're peeling off gets rid of any lint that will end up on your screen, which reduces bubbles. I didn't believe it until I got a perfect application a few days ago. This was with a really cheap screen protector too (I ended up taking it off, it got scratched in like a day...lol).
Also...you can tape some handles on the screen protector to avoid your hands actually touching the sticky side. This is key, IMO. Any time you touch the side, you are at risk for lint.

I just recently put on an invisible shield... i dropped my phone shortly after. Now there are two thin cracks on the phone. Very straight and thin. I cant tell if its a screen crack (i think it is) or just a defect in the screen protector (i hope it is). Aghhhh
Thanks, using my Gucci Nexus on XDA premium
Phone: Galaxy Nexus ROM: AOKP build 39 Kernel: 3.0.34 - Cyangenmod Recovery: ClockworkMod Recovery Launcher: TouchWizUx Additions: S3 Addon (update 14.06.2012)

is the S3's glass/screen not totally flat?

not sure if it's just a bad screen protector or the screen is not entirely flat, but it seems kinda strange to me that only the edges of the phone that the screen protector won't stick. i've never seen this in any of my previous SP installations. any thoughts anyone? btw, these are the really cheap SPs from ebay, but they've always worked for me.

Correct, screen is not flat. Take a good look at the edges and you'll see they curve awat in the last few mm.
Sent from my SPH-L710 using xda app-developers app

falconator said:
Correct, screen is not flat. Take a good look at the edges and you'll see they curve awat in the last few mm.
Sent from my SPH-L710 using xda app-developers app
Click to expand...
Click to collapse
It looks pretty cool imo. Like when you drop water onto a penny.

That is why some screen protectors don't cover the entire front of the GS3. If it bothers you I believe this screen protector is slightly smaller than the front so it doesn't leave those lifted edges.
http://www.amazon.com/Ultimate-Rear...41&sr=8-1&keywords=galaxy+s3+screen+protector

manchild83 said:
That is why some screen protectors don't cover the entire front of the GS3. If it bothers you I believe this screen protector is slightly smaller than the front so it doesn't leave those lifted edges.
http://www.amazon.com/Ultimate-Rear...41&sr=8-1&keywords=galaxy+s3+screen+protector
Click to expand...
Click to collapse
the SP i had on is slightly smaller than the screen already, but i don't think this is the problem here though, instead i think it's my screen's edges that is not flush. has anybody else with a S3 that has this problem? it would suck going back to costco and telling them this is the reason i wanted to exchange my phone.

its ur screen protector

MMakoto said:
the SP i had on is slightly smaller than the screen already, but i don't think this is the problem here though, instead i think it's my screen's edges that is not flush. has anybody else with a S3 that has this problem? it would suck going back to costco and telling them this is the reason i wanted to exchange my phone.
Click to expand...
Click to collapse
the entire edge of the screen is beveled downward to create a curve at the edges. run your finger along the edges and you'll notice it, it's pretty substantial and was an intended design. if you want a protector that will cover all the edges you will need a flexible one. u suggest the skinomi one that's on sale on Amazon.
Sent from my Galaxy S III

dLo GSR said:
the entire edge of the screen is beveled downward to create a curve at the edges. run your finger along the edges and you'll notice it, it's pretty substantial and was an intended design. if you want a protector that will cover all the edges you will need a flexible one. u suggest the skinomi one that's on sale on Amazon.
Sent from my Galaxy S III
Click to expand...
Click to collapse
So does that mean all the S3s are with the same glass design and mine is not a defect?
Sent from my SGH-T999 using xda app-developers app

MMakoto said:
So does that mean all the S3s are with the same glass design and mine is not a defect?
Sent from my SGH-T999 using xda app-developers app
Click to expand...
Click to collapse
Did you really even have to ask that?
And this is really unfortunate. My 5 for $0.99 screen protectors from ebay have the same stupid 2mm non-sticking edge at the top/bottom. Maybe I just use a scalpel to cut the next one before I apply it? Might leave a really sharp edge though..

SGP has a Flex HD protector that is supposed to offer full screen coverage. It's $18 but I'm going to give it a shot.
Sent from my SGH-T999 using Tapatalk 2

I have used belkin and incipio protectors, and both do not stick around the edges of the phone. It does detract from appearance a bit, but I am not going to worry about it anymore. I have yet to see a screen protector that is 100% flush with the screen.

A tip for those who got the same screen protector. If you have a hair blow dryer, hot blow dry the screen protector first to the point where it gets kinda soft, peel off the part 1 of the SP then apply it. blow drying the SP would soften it and would make it cooperate to stick in the screen. Now, I haven't tried this as I had just ordered the SP similar to this but I've tried the same method when I had the htc sensation(contour glass). There's a big possibilty that this would work
Sent from my SGH-T999

Xcor3 said:
A tip for those who got the same screen protector. If you have a hair blow dryer, hot blow dry the screen protector first to the point where it gets kinda soft, peel off the part 1 of the SP then apply it. blow drying the SP would soften it and would make it cooperate to stick in the screen. Now, I haven't tried this as I had just ordered the SP similar to this but I've tried the same method when I had the htc sensation(contour glass). There's a big possibilty that this would work
Sent from my SGH-T999
Click to expand...
Click to collapse
Nice suggestion, but it doesn't make the glue more gummy or anything? Would really have appreciated it if samsung took this into account before they put this odd curve on the glass. Why don't phone companies just ship screen protectors and cases with their phones? In fact the casing should be shock resistant and cheap to replace on EVERY phone. Maybe just a chassis and then you put whatever case around it even.
90% of people stick their nice phone in an ugly $2.99 case. It's a huge market that samsung and others are just giving away. The $39.99 cases don't look any better either...

Screen protectors with cut outs?

Are there any screen protectors that have cut out for the camera and such on top and for the home button? and like one of the high end scree nprotectors

If there are must be a wet application protector. Like zagg or similar. I have xtremeguard which is similar as zagg and covers mostly the complete front.
Sent from my Galaxy S3 using neighbors wifi

Zag does cover all of the front except right underneath the home button if I recall correctly
Sent from my SPH-L710 using xda premium

I got some from monoprice.com. They seem to be of good quality and easy on the pocket book. Be sure to clean your screen very carefully before applying a screen protector.

Marko56 said:
I got some from monoprice.com. They seem to be of good quality and easy on the pocket book. Be sure to clean your screen very carefully before applying a screen protector.
Click to expand...
Click to collapse
will definitely check those out...:good:

Planning to get zagg full body + otter box commuter incase of hits on corners but the screen protector covers everything but below the home button and parts of top
Sent from my GT-I9300 using xda premium

My fav: http://www.spigen.com/samsung-galaxy-s3-screen-protector-steinheil-curved-crystal.html

Yeah I was planning to get that, but I can't find any store in Toronto that had that and it's not a spray one so it'll be hard for me
Sent from my GT-I9300 using xda premium

The ghost armour protector has cutouts for the camera, light/proximity sensor, and home button.

compro01 said:
The ghost armour protector has cutouts for the camera, light/proximity sensor, and home button.
Click to expand...
Click to collapse
hm, i was recommended this, but if i buy it online i wouldn't get the solution apparently but would a zagg solution work

Check out DBA Just Like Glass, has a cutout for the home button and the camera. I got it and put it on a couple weeks ago, feels amazing and I can barely tell it's on there.
Sent from my SCH-I535 using Tapatalk 2

thesoldier said:
Check out DBA Just Like Glass, has a cutout for the home button and the camera. I got it and put it on a couple weeks ago, feels amazing and I can barely tell it's on there.
Sent from my SCH-I535 using Tapatalk 2
Click to expand...
Click to collapse
really? Lol i can't find anything about that on the web

The realook has cutouts as well
Sent from my Galaxy S3 using neighbors wifi

anthonyly said:
really? Lol i can't find anything about that on the web
Click to expand...
Click to collapse
Here ya go.
http://www.dbacases.com/samsung-galaxy-s3-screen-protectors.aspx
The name definitely applies, I really can't even tell there's a screen protector on based on feel...only if I look at the outline of it. I also got it from Amazon instead of their site since I had a gift card. Great protector!
Sent from my SCH-I535 using Tapatalk 2

thesoldier said:
Here ya go.
http://www.dbacases.com/samsung-galaxy-s3-screen-protectors.aspx
The name definitely applies, I really can't even tell there's a screen protector on based on feel...only if I look at the outline of it. I also got it from Amazon instead of their site since I had a gift card. Great protector!
Sent from my SCH-I535 using Tapatalk 2
Click to expand...
Click to collapse
i thought the justlikeglass only covers the screen and nothing more... from pics ive seen

anthonyly said:
hm, i was recommended this, but if i buy it online i wouldn't get the solution apparently but would a zagg solution work
Click to expand...
Click to collapse
The "application solution" is just demineralized water and a bit of soap.
The ghost armour kit just has you make it yourself. Add a single drop of whatever dish soap to the spray bottle they give you, fill with demin water, shake vigorously, and spray.

seriously, dont waste your time and get the SGP Ultra clear nano, its crystal clear , unlike most with the orange peel effect. And has cut outs for the home button and camera. Comes with 3 in a pack. I tried 2 others before and literally put them on, instantly ripped them off and threw in the trash, didnt even try to get my money back and on the third try put the ultra clear nano on there and it was absolutely perfect, I have the slim diz case on it and the nano goes right to the edge of the case so there is no peeling or anything.

compro01 said:
The "application solution" is just demineralized water and a bit of soap.
The ghost armour kit just has you make it yourself. Add a single drop of whatever dish soap to the spray bottle they give you, fill with demin water, shake vigorously, and spray.
Click to expand...
Click to collapse
if we order online, can we go to one of their shops for like those 5$ replacement... how do they even know if its ghost armour

and do you guys know if dba has warranty?

I have a simple Belkin screenguard,
Its ok, Its 10 euro for 3 pieces, Very clear and easy to apply

eBay glass screen protector

Hello,
I bought an off brand glass screen protector for my ONE and received and applied today. It's better than I imagined it would be. And way cheaper than the spigen or seidio. Watch the unboxing here
https://www.youtube.com/watch?v=4P4cPwP7w9U&feature=youtube_gdata_player
And what it looks like after being applied.
https://www.youtube.com/watch?v=peJZ7LlJoUA&feature=youtube_gdata_player
If you're interested in the same one I bought, I got this one : http://pages.ebay.com/link/?nav=item.view&id=331019841878
Sent from my HTC6500LVW using Tapatalk 2

I'm about to order one. How did you go about applying it?

Let us know how it goes after a weeks worth of experience with it! I'm interested in purchasing one myself!!!
Also, what is the thickness that you picked?

dnalevelc said:
I'm about to order one. How did you go about applying it?
Click to expand...
Click to collapse
Very carefully. Lol. I lined up the bottom edge with where the metal and glass meet. Its easier than explained. I did mess up the first time, it was crooked. I used tape to pull up the screen protector then lined it up again. The instruction says to push down on the center. I didn't have to it automatically started to suck itself onto the phone screen. Definitely an interesting thing to watch. It stopped before it was completely adhered. So I did have to put pressure on the edge. The are tiny micro bubbles that are seen immediately after adhesion, but they dissipate after some time. however my corners seem to not be adhered correctly. I left it over night with an iPad on top to add weight hoping it would flatten out. No such luck. I'm wondering what else i can try...
Sent from my HTC6500LVW using Tapatalk 2

aljr1021 said:
Let us know how it goes after a weeks worth of experience with it! I'm interested in purchasing one myself!!!
Also, what is the thickness that you picked?
Click to expand...
Click to collapse
I will. It's 0.4 mm thickness. I can tell you this the oleophobic coating is worth it. Plastic screen protectors are always greasy and you can't seen to wipe it off enough. These don't have that problem. I'll keep you updated though.
Sent from my HTC6500LVW using Tapatalk 2

I have one of these, from the same supplier arriving this week. Do you use a case on your phone? Interested to know if this interferes with the fit of it if you do.
Interesting to hear your account of fitting this. I thinks i will securely tape a carefully aligned straight edge steel ruler to the phone and use that as a bump stop type tool to try and get it on first go.

adamjamess said:
I will. It's 0.4 mm thickness. I can tell you this the oleophobic coating is worth it. Plastic screen protectors are always greasy and you can't seen to wipe it off enough. These don't have that problem. I'll keep you updated though.
Sent from my HTC6500LVW using Tapatalk 2
Click to expand...
Click to collapse
You reffered to the SGP model of the glass screen protector, due to the packaging.
My question, how sharp are the edges of this screen protector with swiping the toolbar down for example, since SGP released a rounded version of the protector to get the sharp edges of.

astmacca said:
I have one of these, from the same supplier arriving this week. Do you use a case on your phone? Interested to know if this interferes with the fit of it if you do.
Interesting to hear your account of fitting this. I thinks i will securely tape a carefully aligned straight edge steel ruler to the phone and use that as a bump stop type tool to try and get it on first go.
Click to expand...
Click to collapse
I'm using this protector (same Chinese) knockoff I bought on amazon. With a super sweet case/bumper also purchased on amazon.. the glass is slightly narrower than the stock screen. I have no issues with the glass and the case.
Case : http://www.amazon.com/gp/aw/d/B00C3HA9VI/ref=ya_aw_oh_pit
Glass : http://www.amazon.com/gp/aw/d/B00DNWJIIC/ref=ya_aw_oh_pit
Tapped via TapaCrap from my Goggle Edition HTC One

Flomaster said:
I'm using this protector (same Chinese) knockoff I bought on amazon. With a super sweet case/bumper also purchased on amazon.. the glass is slightly narrower than the stock screen. I have no issues with the glass and the case.
Case : http://www.amazon.com/gp/aw/d/B00C3HA9VI/ref=ya_aw_oh_pit
Glass : http://www.amazon.com/gp/aw/d/B00DNWJIIC/ref=ya_aw_oh_pit
Tapped via TapaCrap from my Goggle Edition HTC One
Click to expand...
Click to collapse
Same applies for my last post. How's yours,sharp edges and do they annoy you?

Stormingsoul said:
You reffered to the SGP model of the glass screen protector, due to the packaging.
My question, how sharp are the edges of this screen protector with swiping the toolbar down for example, since SGP released a rounded version of the protector to get the sharp edges of.
Click to expand...
Click to collapse
They are beveled edges, nothing sharp. Feels good.
Sent from my HTC6500LVW using Tapatalk 2

Stormingsoul said:
Same applies for my last post. How's yours,sharp edges and do they annoy you?
Click to expand...
Click to collapse
They aren't sharp like a piece of glass in a picture frame. It's somewhat beveled but not rounded off and super smooth. Well worth the money for me.
Tapped via TapaCrap from my Google Edition HTC One.

adamjamess said:
I will. It's 0.4 mm thickness. I can tell you this the oleophobic coating is worth it. Plastic screen protectors are always greasy and you can't seen to wipe it off enough. These don't have that problem. I'll keep you updated though.
Sent from my HTC6500LVW using Tapatalk 2
Click to expand...
Click to collapse
ah, okay dope, thanks man. May order soon tho!! But I'm still waiting for some stuff for my phone so after that I'll see if you got any updates on the screen!

Got the same screen protector from the same supplier as the OP today.
Very easy to install. No bubbles
Nice rounded edges, and as it is lightly smaller than the screen, my case fits well.
Texture very slick. Once on and in the case you wouldn't actually know it has a screen protector on apart from the small rise next to each speaker which you would take as part of the phone if you weren't familiar with the HTC One..

I will never go back to plastic SPs. This is legit! Even though an edge didn't completely adhere this thing rocks.
Sent from my HTC6500LVW using Tapatalk 2

Finally! Screen protector

I've tried 6 screen protectors and finally found one without any issues. #5 was a zizo and it fit but had a stupid rainbow and the top corner randomly broke in my pocket after a month.
I bought this one on ebay. It covers the whole screen, fits perfectly, has a curved screen, no rainbow, air bubbles, and doesn't lift up at the ends. I'm finally happy with my screen protector
http://www.ebay.com/itm/252678476834

Do you use a case with the phone?

I thought someone tried this on the main thread for screen protectors and said it was just another Zizo. I really don't care about the rainbow. I just hate the smudges
Sent from my Pixel C using Tapatalk

eRRoRist said:
Do you use a case with the phone?
Click to expand...
Click to collapse
Yes this one
https://www.amazon.com/dp/B01LYC88EN

Joediver53 said:
I thought someone tried this on the main thread for screen protectors and said it was just another Zizo. I really don't care about the rainbow. I just hate the smudges
Click to expand...
Click to collapse
It looks similar to zizo but it isn't (I've bought both).

UPSGuy said:
I've tried 6 screen protectors and finally found one without any issues. #5 was a zizo and it fit but had a stupid rainbow and the top corner randomly broke in my pocket after a month.
I bought this one on ebay. It covers the whole screen, fits perfectly, has a curved screen, no rainbow, air bubbles, and doesn't lift up at the ends. I'm finally happy with my screen protector
http://www.ebay.com/itm/252678476834
Click to expand...
Click to collapse
Would you be so kind post few picture how it looks like please.

I am joining netgar with the request of pictures.
If you can please show how it looks with and without the case.
Thanks!

UPSGuy said:
I've tried 6 screen protectors and finally found one without any issues. #5 was a zizo and it fit but had a stupid rainbow and the top corner randomly broke in my pocket after a month.
I bought this one on ebay. It covers the whole screen, fits perfectly, has a curved screen, no rainbow, air bubbles, and doesn't lift up at the ends. I'm finally happy with my screen protector
http://www.ebay.com/itm/252678476834
Click to expand...
Click to collapse
So, this is interesting, I bought the zizo combination case and glass screen protector combo amd it looks EXACTLY like the one you're mentioning here. It's actually really great. No rainbow or bubbling and full-screen exactly like this one.

TheBigL said:
I am joining netgar with the request of pictures.
If you can please show how it looks with and without the case.
Thanks!
Click to expand...
Click to collapse
Sorry, the only way I have to take pictures is with the phone itself in a mirror (not terribly useful) or with the web cam on my new laptop which of course is of an awful quality. Here is the best I could get...

Would be nice if you use a friend's phone and take some pictures of the screen protector installed. I'm not being rude and appreciate your attempts at photographing it, but honestly they're pointless as they show us nothing
Sent from my LG V20 using XDA Labs

For $7 I'm going to give it a shot. Same price on Amazon for Supershieldz and 2 day delivery. Will update when installed
UPDATE: My Supershieldz TGP arrived and before heading out of town on business I installed and can confirm NO HALO. This is not just a Zizo close. Been using it for a couple of days now and while there is still smudging it's not as bad as the Zizo. I'll try to post some photos using my 6p when I get home

stanglifemike said:
Would be nice if you use a friend's phone and take some pictures of the screen protector installed. I'm not being rude and appreciate your attempts at photographing it, but honestly they're pointless as they show us nothing
Sent from my LG V20 using XDA Labs
Click to expand...
Click to collapse
I'm with stanglifemike...
U can't see anything in those pictures.

I've ordered a zizo and a couple of the others that look the same and I'm done. All the ones I get smudge like crazy and have the rainbow effect.
I'm just gonna wait until there's a definite consensus on one that doesn't have those issues.
I'm currently using an Armor shield wet protector and it's pretty good for plastic. Better than the glass protectors as far clarity/smudge resistance but the glass is obviously better as far as feel goes.

Anybody knows a good matte/Anti-Glare screen protecror that covers the whole screen?

I pried my wife's iphone 7 plus out of her hands long enough to take these.

Is there adhesive on the clear part of the glass? Not just on the black trim. That's the cause of the oil spill under the screen. No adhesive to hold it tight to the phone like the clear tempered shields.
Sent from my VS995 using XDA-Developers Legacy app

666syco said:
Is there adhesive on the clear part of the glass? Not just on the black trim. That's the cause of the oil spill under the screen. No adhesive to hold it tight to the phone like the clear tempered shields.
Click to expand...
Click to collapse
Not a clue, but whatever is holding it on is clear with no bubbles, bumps or rainbow oil slicks.

UPSGuy said:
Not a clue, but whatever is holding it on is clear with no bubbles, bumps or rainbow oil slicks.
Click to expand...
Click to collapse
And smudges?
Sent from my Pixel C using Tapatalk

Joediver53 said:
And smudges?
Click to expand...
Click to collapse
I've never had a problem with that on any of the 6 I've tried so can't say. No issues here for me.

Joediver53 said:
For $7 I'm going to give it a shot. Same price on Amazon for Supershieldz and 2 day delivery. Will update when installed
UPDATE: My Supershieldz TGP arrived and before heading out of town on business I installed and can confirm NO HALO. This is not just a Zizo close. Been using it for a couple of days now and while there is still smudging it's not as bad as the Zizo. I'll try to post some photos using my 6p when I get home
Click to expand...
Click to collapse
I was not about to stick my finger on the adhesive side to check if the center has adhesive but with no halos can't think of another explanation