Develop Bugs

[Q] "Android" Logo Bootloop

Yesterday I wanted to flash the new CWM (5.8.4.0) but I accidentally flash using fastboot boot boot.img
Then it kept rebooting into recovery
After panicking a few times, I used Hasoon2000's allinonekit to flash stock recovery, stock kernel, relocked and reunlocked bootloader, factory reset through hboot.
Now im in a bootloop but instead of the usual htc with beats that i usually get, a simple logo featuring the word "android" is all that showed up on my screen. Sometime when I restart it would show a harddisk or something like that with a green refresh logo. In cwm my phone can't detect my sd so I can't flash my nandroid backup.
Can someone help this noob

Boot into fastboot.
First turn on the phone.
Hold both Power and Volume Down until the screen turns black, after two seconds release the power button only, it should boot you into fastboot, you can also try just holding both buttons, not sure about that so if it won't boot into fastboot try both ways!
When it boots into fastboot, open up command prompt and execute the command fastboot erase cache, this should make you able to boot into recovery again.
Good luck!

I can access recovery now. The problem now is the android bootloops

Katang said:
I can access recovery now. The problem now is the android bootloops
Click to expand...
Click to collapse
Do you have any ROMS on your SDCard?
If you do, follow these steps please!
First of all, find the boot.img of the ROM you have on your SDCard, do this by downloading the ROM to your computer again and extracting the boot.img or using franco's or whatever other one there is.
Put the boot.img into the directory where your fastboot.exe is located, boot back into Fastboot and execute the following commands, fastboot flash boot boot.img and then fastboot erase cache.
Boot into recovery from fastboot, Wipe Data -> Wipe Cache, browse for the ROM and flash it, this should fix your phone!

I was running ARHD 6.1.1 before. but like I said in CWM it cant detect my sd,
it says there is no such file. any ideas?

Katang said:
I was running ARHD 6.1.1 before. but like I said in CWM it cant detect my sd,
it says there is no such file. any ideas?
Click to expand...
Click to collapse
Yes, flash this CWM.
http://lh.rs/Zs6RYrc8m7Os
Put phone into Fastboot and run following commands.
fastboot flash recovery r1--recovery-clockwork-touch-endeavoru.img
fastboot erase cache
Boot into recovery see if it recognizes the SD.

flashed that recovery, cleared the cache
when I went into recovery i chose zip from sdcard but then no files found
in Hboot it said SD checking...
failed to open usb master mode
failed to open usb master mode
only then would it show the options:
fastboot
recovery
factory reset
simlock
showbarcode
image crc

Katang said:
flashed that recovery, cleared the cache
when I went into recovery i chose zip from sdcard but then no files found
in Hboot it said SD checking...
failed to open usb master mode
failed to open usb master mode
only then would it show the options:
fastboot
recovery
factory reset
simlock
showbarcode
image crc
Click to expand...
Click to collapse
what is your recovery version? 5.8.4.0?
If you flash the latest recovery 5.8.4.0, then you should be able to view your SD Card and also infact,
if you go to ADVANCED Mode in the latest Recovery, connect the USB, it will detect your PC. Transfer the required files.
You have recovery now, try mounting the SD Card. Make sure you have enough charge ( >50%)
Please do not panic!

I will try that. Although i don't know how much battery I have left cause it suddenly turns on and bootloops after I charge for a particular amount of time

did you fix your phone now? if you fix pls mail [email protected] me cos we have same problem im using HOX stock " android logo "
even i put file on cwm 5.8.4.0 SD failed open master mode

[Q] I think i Bricked my device

I seemed to have bricked my device......... the phone just seems to hang on the white HTC screen.. I am very new to all this so please help with even the most basic and obvious steps.
Events that led to this:
Last night i unlocked and rooted my phone using clockwork recovery and then installed superSU. All was fine then.
I installed Nanobackup and took the backup as suggested.
then later today, after reading a lot i decided to try CYANOGENMOD'S root and then it all statred to fall apart.......
the phone never booted after that. first it used to get stuck on CYNOGENMOD's startup screen and it never moved forward. after reading some more I realised that i needed to update the BOOT.IMG file along with it which i missed. after this also nothing was happening.
I was thanking my stars that i took a complete back up and tried to restore it..... but as my luck would have it that also did not work.
Now i am stuck with a white boot up screen with the HTC logo on it. I can still connect to fastboot....... PLease help......Very desparate.
Thanks..... all and any help is appreciated.

flash the boot.img wich came with your rom then "fastboot erase cache" + go to recovery then wipe data + cache + dalvik cache then your good to go

No luck
The5alodi said:
flash the boot.img wich came with your rom then "fastboot erase cache" + go to recovery then wipe data + cache + dalvik cache then your good to go
Click to expand...
Click to collapse
Hi Thanks i tried all this again just to be sure.... but no help.
The command i am using for Fastboot is
Fastboot boot boot.img
This is correct??? Also just to be sure i have the correct boot file should i download the .zip file again.
Also i forgot to add that i installed CM downloader from Google play from there i directly downloaded the CM10 ROM. Is this why there could be a problem?

the correct command is: fastboot flash boot boot.img
Then fastboot erase cache

the command is "fastboot flash boot boot.img" the "fastboot erase cache" get the rom from this site its under original android development pick what ever you want
you will find steps in the rom page if you ddnt understand me
http://forum.xda-developers.com/showthread.php?t=1786696
original cm10

Still not luck
The5alodi said:
the command is "fastboot flash boot boot.img" the "fastboot erase cache" get the rom from this site its under original android development pick what ever you want
you will find steps in the rom page if you ddnt understand me
http://forum.xda-developers.com/showthread.php?t=1786696
original cm10
Click to expand...
Click to collapse
Ok tired this but still no luck. is there is way to tranfer the new downloaded .zip file to the sdcard as this is only option i see left.

anupamdalvi said:
Ok tired this but still no luck. is there is way to tranfer the new downloaded .zip file to the sdcard as this is only option i see left.
Click to expand...
Click to collapse
dude when you download the rom first extract the boot.img and flash it via fastboot + erase cache of course you are in fastboot usb in your one x
then go to recovery >mounts >mount usb storage then transfer the file and flash it by recovery
then erase dalvik cache + wipe data
any Q pm me if i helped click the thanks button

[Q] Forgot to install ROM before the custom recovery.

I was following this guide with the intention of installing Cyanogenmod on to my HTC One X (international version), and I got as far as the Flashing a ROM section, towards the bottom, when I reached step 5, which reads "Make sure you already have your shiny new ROM .zip on your internal memory as you cannot enable mass storage in the current recovery builds."
At this point I realised I had not done this, and I have no way of putting the ROM onto the phone. Is there anything I can do, or do I have to start from scratch, and if so, how do I do that?
I'm following this guide regarding installing the ROM, but is there a better one? That guy cannot spell.
I also have this thread open for CM10.1, but it's quite confusing. Should I be downloading the following?: Beta 7 (pure JB vendor): http://d-h.st/fo4 - Kernel 3.1.10 included.
Thanks in advance.

ashleynicholson said:
I was following this guide with the intention of installing Cyanogenmod on to my HTC One X (international version), and I got as far as the Flashing a ROM section, towards the bottom, when I reached step 5, which reads "Make sure you already have your shiny new ROM .zip on your internal memory as you cannot enable mass storage in the current recovery builds."
At this point I realised I had not done this, and I have no way of putting the ROM onto the phone. Is there anything I can do, or do I have to start from scratch, and if so, how do I do that?
I'm following this guide regarding installing the ROM, but is there a better one? That guy cannot spell.
I also have this thread open for CM10.1, but it's quite confusing. Should I be downloading the following?: Beta 7 (pure JB vendor): http://d-h.st/fo4 - Kernel 3.1.10 included.
Thanks in advance.
Click to expand...
Click to collapse
have you already installed the custom recovery?

matt95 said:
have you already installed the custom recovery?
Click to expand...
Click to collapse
Yes, and "backed up." I don't know what I've backed up, but I've backed up something. I have not wiped anything, and I still appear to have a functional phone.

you probably backed up the stock rom however to push the rom onto your phone you should go into recovery and mount USB and the put the rom onto the sdcard that's it...

matt95 said:
you probably backed up the stock rom however to push the rom onto your phone you should go into recovery and mount USB and the put the rom onto the sdcard that's it...
Click to expand...
Click to collapse
How do I mount USB? When I plug my phone in I just get weird tethering options.

ashleynicholson said:
How do I mount USB? When I plug my phone in I just get weird tethering options.
Click to expand...
Click to collapse
you need to go into recovery and there is an option for mounting partitions

matt95 said:
you need to go into recovery and there is an option for mounting partitions
Click to expand...
Click to collapse
Do I just place the file in the main folder, or does it go somewhere specific? Thanks for your help by the way.

You can mount it inside the recovery as a diskdrive and yes you need that cm10.1 + gapps if you want them too. Mount it and copy the rom and gapps to it
Here is a small tut i wrote earlier. ...
This counts for recovery cwm 5.8.4.0 (otherwise a full wipe in any other recovery must be done)
In recovery
Wipe data/factory reset
Wipe cache partition
Advanced - wipe dalvik cache
Mounts and storage - format cache,data,system
Remove the cable to the pc before installing the rom !
Then install CM10.1 after that GAPPS.....DO NOT REBOOT
Reconnect the cable and ......
type in the fastboot command window
Adb reboot bootloader
Fastboot erase cache
Fastboot flash boot boot.img (the file from the rom)
Fastboot erase cache
Fastboot reboot

Mr Hofs said:
You can mount it inside the recovery as a diskdrive and yes you need that cm10.1 + gapps if you want them too. Mount it and copy the rom and gapps to it
Here is a small tut i wrote earlier. ...
This counts for recovery cwm 5.8.4.0 (otherwise a full wipe in any other recovery must be done)
In recovery
Wipe data/factory reset
Wipe cache partition
Advanced - wipe dalvik cache
Mounts and storage - format cache,data,system
Remove the cable to the pc before installing the rom !
Then install CM10.1 after that GAPPS.....DO NOT REBOOT
Reconnect the cable and ......
type in the fastboot command window
Adb reboot bootloader
Fastboot erase cache
Fastboot flash boot boot.img (the file from the rom)
Fastboot erase cache
Fastboot reboot
Click to expand...
Click to collapse
Thanks for your comprehensive reply dude. Does the gapps (Google Apps I assume?) include Google Now? I'd become quite accustomed to that particular gadget and I will miss it.

Actually i have to guess yes.....i never tried it !
Ow and my apology to matt for barging in like this......

Mr Hofs said:
Actually i have to guess yes.....i never tried it !
Ow and my apology to matt for barging in like this......
Click to expand...
Click to collapse
Ok, once this gapps is downloaded I am good to go I think. If I brick it I can just break it and claim it on the insurance. Although this phone is brand new because my old one drowned a couple weeks ago, so they mightn't like two claims in such quick succession.

yeah gapps have google now too

matt95 said:
yeah gapps have google now too
Click to expand...
Click to collapse
One more question guys, and this is where I possibly reveal how idiotic I am...
How do I install the ROM? I have the two files on the storage (in unzipped folders), but how do I install them?

ashleynicholson said:
One more question guys, and this is where I possibly reveal how idiotic I am...
How do I install the ROM? I have the two files on the storage (in unzipped folders), but how do I install them?
Click to expand...
Click to collapse
you need the cm10.1 rom.zip and the gapps.zip... go into recovery choose .zip and select the rom.zip first, after that install the gapps.zip following the same steps before... then reboot and enjoy the rom

matt95 said:
you need the cm10.1 rom.zip and the gapps.zip... go into recovery choose .zip and select the rom.zip first, after that install the gapps.zip following the same steps before... then reboot and enjoy the rom
Click to expand...
Click to collapse
Got it.
Can you explain the second half of your instructions please?
[quotetype in the fastboot command window
Adb reboot bootloader
Fastboot erase cache
Fastboot flash boot boot.img (the file from the rom)
Fastboot erase cache
Fastboot reboot[/quote]

Well you have a certain folder on the pc....from where you also flashed the recovery ? It contains fastboot.exe and adb.exe files ....right? You open the cm10.1.zip file and you see the boot.img file in there, you copy that to the fastboot folder on the pc and flash it

ashleynicholson said:
Got it.
Can you explain the second half of your instructions please?
[quotetype in the fastboot command window
Adb reboot bootloader
Fastboot erase cache
Fastboot flash boot boot.img (the file from the rom)
Fastboot erase cache
Fastboot reboot
Click to expand...
Click to collapse
[/QUOTE]
oh yeah forgot about that sorry...
before going into recovery you should go into fastboot mode, connect the phone to your computer and type those command in the terminal/cmd, the boot.img file can be easily found in the cm10.1 thread or in the rom.zip... after that install the rom following the steps above...

Mr Hofs said:
Well you have a certain folder on the pc....from where you also flashed the recovery ? It contains fastboot.exe and adb.exe files ....right? You open the cm10.1.zip file and you see the boot.img file in there, you copy that to the fastboot folder on the pc and flash it
Click to expand...
Click to collapse
I'm on a Mac, so the guide said I only needed the fastboot file, not the adb one. What do you mean "flash it"?
I've rebooted the phone as you said, but it just says "Unfortunately, the process com.android.phone has stopped." I click Ok and it says that again.

ashleynicholson said:
I'm on a Mac, so the guide said I only needed the fastboot file, not the adb one. What do you mean "flash it"?
I've rebooted the phone as you said, but it just says "Unfortunately, the process com.android.phone has stopped." I click Ok and it says that again.
Click to expand...
Click to collapse
fastboot mode: power off the phone, power+vol down, select fastboot and press power, you're done

You can go in the bootloader first and flash the boot.img. I described it the other way around because you end with a cache erase to avoid boot problems (got this from the thread itself)
Basically it comes down to this
You put the phone in the bootloader and you see a red text that says "fastboot usb"
At that point you flash the boot.img from the mac to the phone.
Then you unhook the cable and do the rest of the guide

[Q] I think I've bricked my phone completely

Hello, I was flashing the latest version of ViperX and it wouldn't boot so I decided to reinstall. After reinstalling I updated my hboot to the latest version and was told to erase everything such as cache, system, dalvik etc. It deleted my backups, I have lost ClockWorkMod on my phone and ADB wont detect it. I also have no rom on my phone as of now, I think I could fix it if I could get ADB to detect the phone. When I plug my phone into the computer it detects it as a HTC but when I type "adb devices" I get nothing coming up
Could someone suggest something to fix it?

Hold your volume - and the power button together until you see the bootloader !
Is the bootloader unlocked ? And what version do you have now ?
Unlock the bootloader if its relocked. Put the unlock code.bin file in the fastboot folder and flash it
Fastboot flash unlocktoken unlock_code.bin
Download this file and place it in your fastboot folder, rename it to recovery.img and flash it
http://db.tt/S74XQEtu
Fastboot flash recovery recovery.img
Fastboot erase cache

Mr Hofs said:
Hold your volume - and the power button together until you see the bootloader !
Is the bootloader unlocked ? And what version do you have now ?
Click to expand...
Click to collapse
I was about to add this extra information. I've updated my bootloader and its been relocked, its at version 1.39

derp

Thanks for the help guys, it spontaneously worked

So you got viper x up and running ?

Mr Hofs said:
So you got viper x up and running ?
Click to expand...
Click to collapse
Well I'm getting there.
I've reinstalled CWM and I'm looking to install the ROM now but it has been deleted from my SD card, either that or my sd isn't working.
Is there a way to access my sd card without a ROM Wmaybe install and flash without using the "choose zip from sdcard" option?
When I press "choose zip from sdcard" it says "No files found."
What do I do now?

Select mounts and storage and mount usb storage.
(if you get an error (ums) DL this: http://download2.clockworkmod.com/recoveries/recovery-clockwork-touch-5.8.4.0-endeavoru.img fastboot flash recovery recovery.img)

Then copy the viper x rom to the sdcard.
Make a full wipe in the recovery
Factory reset
Wipe cache partition
Advanced - wipe dalvik cache
Mounts & storage - format cache, system, data
Then install the rom.....do not reboot if you did not flash the boot.img
Type in the commond prompt
Adb reboot bootloader
Then flash the boot.img from the viper x rom, found inside the rom.zip !
Fastboot erase cache
Fastboot flash boot boot.img
Fastboot erase cache
Fastboot reboot
If you already flashed the boot.img you can skip the last part

TToivanen said:
Select mounts and storage and mount usb storage.
(if you get an error (ums) DL this: http://download2.clockworkmod.com/recoveries/recovery-clockwork-touch-5.8.4.0-endeavoru.img fastboot flash recovery recovery.img)
Click to expand...
Click to collapse
Thanks, that solves the error. How can I add a rom to the sd card without a rom present? I need to access the zip files to install it

Mr Hofs said:
Then copy the viper x rom to the sdcard.
Make a full wipe in the recovery
Factory reset
Wipe cache partition
Advanced - wipe dalvik cache
Mounts & storage - format cache, system, data
Then install the rom.....do not reboot if you did not flash the boot.img
Type in the commond prompt
Adb reboot bootloader
Then flash the boot.img from the viper x rom, found inside the rom.zip !
Fastboot erase cache
Fastboot flash boot boot.img
Fastboot erase cache
Fastboot reboot
If you already flashed the boot.img you can skip the last part
Click to expand...
Click to collapse
This may be a stupid question but how to I get the rom on the sd card?

Select mounts and storage inside the recovery and then mount as mass storage device .....last option of the list

Connect usb cable (obvious) and it pops up on your pc. Then just copy it over.

TToivanen said:
Connect usb cable (obvious) and it pops up on your pc. Then just copy it over.
Click to expand...
Click to collapse
Thats it all sorted and working, thanks guys!

Finally ! ....... TT ?

No problem! Now I shall say...
CASE CLOSED
sent from my nokia 6700 classic

TToivanen said:
No problem! Now I shall say...
CASE CLOSED
sent from my nokia 6700 classic
Click to expand...
Click to collapse
LOL ! you forgot to

[Q] [Help?] Huawei p6 softbrick (rooted/TWRP, need to transfer ROM)

Hi guys,
I would really appreciate any help getting out of this pickle (my first time trying to install a ROM).
Here's the situation:
- Running a Huawei P6-C00 Chinese phone
- Was interested in trying a custom ROM (e.g. CleanRom by @surdu_petru) in order to enable Google Apps
- Updated normally to B120 CN as instructed
- Rooted (using Root Wizard)
- Installed customer recovery (TWRP 2.6.3.3)
- Started flash process including advanced wipe in TWRP... wiped system, cache, davlik, etc... :crying:
- Realized that I didn't have the ROM .zip copied to the phone yet
Currently, I'm able to boot into TWRP but cannot connect using adb for sideload (TWRP just says starting sideload but never connects). What do you guys recommend? I don't have a backup of any working ROM or the stock image.
Is there a way to initiate a "standard" restore since I wiped all the caches? ...
Are there some tricks to getting ADB running so I can try to sideload the ROM again? ...
P6-C00 does not have an SD card, but is it possible to load the ROM onto a USB and read it from TWRP?
Thanks for any help!

Did u try connecting to adb?
Sent from my U9200 using XDA Premium 4 mobile app

some help
onetree said:
Hi guys,
I would really appreciate any help getting out of this pickle (my first time trying to install a ROM).
Here's the situation:
- Running a Huawei P6-C00 Chinese phone
- Was interested in trying a custom ROM (e.g. CleanRom by @surdu_petru) in order to enable Google Apps
- Updated normally to B120 CN as instructed
- Rooted (using Root Wizard)
- Installed customer recovery (TWRP 2.6.3.3)
- Started flash process including advanced wipe in TWRP... wiped system, cache, davlik, etc... :crying:
- Realized that I didn't have the ROM .zip copied to the phone yet
Currently, I'm able to boot into TWRP but cannot connect using adb for sideload (TWRP just says starting sideload but never connects). What do you guys recommend? I don't have a backup of any working ROM or the stock image.
Is there a way to initiate a "standard" restore since I wiped all the caches? ...
Are there some tricks to getting ADB running so I can try to sideload the ROM again? ...
P6-C00 does not have an SD card, but is it possible to load the ROM onto a USB and read it from TWRP?
Thanks for any help!
Click to expand...
Click to collapse
you can try it whith a linux pc (ubuntu)
i have the same problem
good luck!

onetree said:
Hi guys,
I would really appreciate any help getting out of this pickle (my first time trying to install a ROM).
Here's the situation:
- Running a Huawei P6-C00 Chinese phone
- Was interested in trying a custom ROM (e.g. CleanRom by @surdu_petru) in order to enable Google Apps
- Updated normally to B120 CN as instructed
- Rooted (using Root Wizard)
- Installed customer recovery (TWRP 2.6.3.3)
- Started flash process including advanced wipe in TWRP... wiped system, cache, davlik, etc... :crying:
- Realized that I didn't have the ROM .zip copied to the phone yet
Currently, I'm able to boot into TWRP but cannot connect using adb for sideload (TWRP just says starting sideload but never connects). What do you guys recommend? I don't have a backup of any working ROM or the stock image.
Is there a way to initiate a "standard" restore since I wiped all the caches? ...
Are there some tricks to getting ADB running so I can try to sideload the ROM again? ...
P6-C00 does not have an SD card, but is it possible to load the ROM onto a USB and read it from TWRP?
Thanks for any help!
Click to expand...
Click to collapse
Did you try it with fastboot?
Gesendet von meinem P6-U06 mit Tapatalk

ext4
taaeem said:
Did you try it with fastboot?
Gesendet von meinem P6-U06 mit Tapatalk
Click to expand...
Click to collapse
i know that he must use a linux pc that for the drivers
ext4 If say it right...

taaeem said:
Did you try it with fastboot?
Click to expand...
Click to collapse
Hi Taaeem,
Thanks for the hint. I read some posts on fastboot and tried the following, but could not get into fastboot mode.
Methods I tried
- Power off phone and then power on while holding vol-down button
- Select Reboot -> System option from TWRP, while holding volume down
- Select Reboot -> Bootloader option from TWRP
From what I understand, fastboot mode should be run from the /boot partition, which I didn't wipe. So any ideas how I can get into fastboot mode?
Thanks again!

Okay, I confirmed that I have at least some kind of fastboot access because I tried "fastboot reboot-bootloader" from command prompt on my PC, and it rebooted the phone (but the phone stayed on boot logo).
- Next time I get fastboot, should I run "fastboot flash [partition] [ROM-file.zip]"?
- If so, what partition should I specify? I'm confused about where this command will send the ROM file, and if so how do I find it from TWRP later on in order to install it?
Thank you!

One more update:
- Even though I'm stuck at boot logo when I try to enter fastboot mode, it looks like there is a somewhat working fastboot connection. I tried running "fastboot flash [partition] ROM.zip" but it fails after 16s ("remote: flash write failure" or "remote: partition does not exist"). I tried flashing to cache / data / system
Should I try @N!ELS huawei p6 suggestion of accessing by Linux? (I don't have one nearby) or am I using fastboot wrong?
Thanks!!
Also:
- I noticed that when I boot into TWRP the device shows as "..." in my system tray USB devices list.
- When I try to boot into fastboot mode, the device shows as "Android Sooner Single ADB Interface" (but phone is still stuck on boot logo)
- However I'm still not able to connect using ADB .. shows "error: device not found" in all cases)
- Finally, after powering off the phone does show the stock charging animation, which gives me hope that this can still be saved :crying:

onetree said:
One more update:
- Even though I'm stuck at boot logo when I try to enter fastboot mode, it looks like there is a somewhat working fastboot connection. I tried running "fastboot flash [partition] ROM.zip" but it fails after 16s ("remote: flash write failure" or "remote: partition does not exist"). I tried flashing to cache / data / system
Should I try @N!ELS huawei p6 suggestion of accessing by Linux? (I don't have one nearby) or am I using fastboot wrong?
Thanks!!
Also:
- I noticed that when I boot into TWRP the device shows as "..." in my system tray USB devices list.
- When I try to boot into fastboot mode, the device shows as "Android Sooner Single ADB Interface" (but phone is still stuck on boot logo)
- However I'm still not able to connect using ADB .. shows "error: device not found" in all cases)
- Finally, after powering off the phone does show the stock charging animation, which gives me hope that this can still be saved :crying:
Click to expand...
Click to collapse
fastboot mode on the P6 doesn't have any kind of ui for fastboot, so it stays on the boot logo, fastboot should work fine.
You could always find an USB OTG cable and connect a FAT32 partitioned mem stick with the .zip on it, TWRP allows flashing from USB memory as far as I know
You are definetely not out of hope, but im not sure about the compability of P6-U06 roms with the C00 variant.
onetree said:
One more update:
- Even though I'm stuck at boot logo when I try to enter fastboot mode, it looks like there is a somewhat working fastboot connection. I tried running "fastboot flash [partition] ROM.zip" but it fails after 16s ("remote: flash write failure" or "remote: partition does not exist"). I tried flashing to cache / data / system
Click to expand...
Click to collapse
Obviously you can't flash the whole zip file to every partition, infact you can't flash a .zip at all, atleast not in fastboot mode, .img extension is used. So don't try flashing the rom manually via fastboot, since you have a high risk of actually bricking the device, if not in the right hands.
Also when booted into TWRP, try "adb devices" in the cmd see if anything shows up.

onetree said:
One more update:
- Even though I'm stuck at boot logo when I try to enter fastboot mode, it looks like there is a somewhat working fastboot connection. I tried running "fastboot flash [partition] ROM.zip" but it fails after 16s ("remote: flash write failure" or "remote: partition does not exist"). I tried flashing to cache / data / system
Should I try @N!ELS huawei p6 suggestion of accessing by Linux? (I don't have one nearby) or am I using fastboot wrong?
Thanks!!
Also:
- I noticed that when I boot into TWRP the device shows as "..." in my system tray USB devices list.
- When I try to boot into fastboot mode, the device shows as "Android Sooner Single ADB Interface" (but phone is still stuck on boot logo)
- However I'm still not able to connect using ADB .. shows "error: device not found" in all cases)
- Finally, after powering off the phone does show the stock charging animation, which gives me hope that this can still be saved :crying:
Click to expand...
Click to collapse
Okay that's good when you are stuck at the logo and you can see your device at your PC you are in fastboot mode, from here you can work with fastboot commands NOT with ADB that will not work. Anyway isn't there a option in TWRP where you can mount your device to USB when that work you can just copy the files on your phone without to go with fastboot. When that don't work you must try to extract the .zip from the ROM you want to install and flash every image with fastboot I think that should work.
Gesendet von meinem P6-U06 mit Tapatalk

tauio111 said:
fastboot mode on the P6 doesn't have any kind of ui for fastboot, so it stays on the boot logo, fastboot should work fine.
You could always find an USB OTG cable and connect a FAT32 partitioned mem stick with the .zip on it, TWRP allows flashing from USB memory as far as I know
You are definetely not out of hope, but im not sure about the compability of P6-U06 roms with the C00 variant.
Obviously you can't flash the whole zip file to every partition, infact you can't flash a .zip at all, atleast not in fastboot mode, .img extension is used. So don't try flashing the rom manually via fastboot, since you have a high risk of actually bricking the device, if not in the right hands.
Also when booted into TWRP, try "adb devices" in the cmd see if anything shows up.
Click to expand...
Click to collapse
Okay so now I'm a bit paranoid about hard-bricking the device, and would rather not try my luck on a ROM that isn't approved for the P6-C00, haha...
At this point I just want to get a working OS installed (restore to the default for P6-C00 phone, even), and then maybe try to safely enable Google Apps. Any suggestions on how I can get this restored?
- I think the device came with a USB cable that is OTG.
- Seems like fastboot is also working, even though "fastboot getvar xxx" returns nothing useful
- ADB does not work while booted into TWRP (can't run shell, sideload, or list devices)

onetree said:
Okay so now I'm a bit paranoid about hard-bricking the device, and would rather not try my luck on a ROM that isn't approved for the P6-C00, haha...
At this point I just want to get a working OS installed (restore to the default for P6-C00 phone, even), and then maybe try to safely enable Google Apps. Any suggestions on how I can get this restored?
- I think the device came with a USB cable that is OTG.
- Seems like fastboot is also working, even though "fastboot getvar xxx" returns nothing useful
- ADB does not work while booted into TWRP (can't run shell, sideload, or list devices)
Click to expand...
Click to collapse
Download this rom for example https://disk.yandex.com/public/?hash=bhDlIAc5AqKh4RAB2IdatPdEfYVI9FH/Zky/UTGcH3M=
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp

tauio111 said:
Download this rom for example https://disk.yandex.com/public/?hash=bhDlIAc5AqKh4RAB2IdatPdEfYVI9FH/Zky/UTGcH3M=
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
Click to expand...
Click to collapse
Thank you! I will try this tonight after work

tauio111 said:
Download this rom for example https://disk.yandex.com/public/?hash=bhDlIAc5AqKh4RAB2IdatPdEfYVI9FH/Zky/UTGcH3M=
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
Click to expand...
Click to collapse
Thanks, tauio111! That worked and I now have a working phone again :victory:
I'm going to be a bit more careful about how to enable Google Apps... this is too much stress during the workweek haha.
Later on what do you think my best option would be?
- Wait for a confirmed easy to install ROM for P6-C00 that supports Google Apps
- Some other way to enable Google Apps with the standard firmware, since I am rooted?
Thanks :laugh:

onetree said:
Thanks, tauio111! That worked and I now have a working phone again :victory:
I'm going to be a bit more careful about how to enable Google Apps... this is too much stress during the workweek haha.
Later on what do you think my best option would be?
- Wait for a confirmed easy to install ROM for P6-C00 that supports Google Apps
- Some other way to enable Google Apps with the standard firmware, since I am rooted?
Thanks :laugh:
Click to expand...
Click to collapse
Easy, flash this via TWRP

tauio111 said:
Easy, flash this via TWRP
Click to expand...
Click to collapse
Thanks @tauio111 and everyone else who helped debug this.
I flashed stock recovery, updated official firmware to B120, re-flashed TWRP, flashed gapps, and now have a working phone with Gmail and Play Store!! :silly:

tauio111 said:
Download this rom for example https://disk.yandex.com/public/?hash=bhDlIAc5AqKh4RAB2IdatPdEfYVI9FH/Zky/UTGcH3M=
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
Click to expand...
Click to collapse
I have the same problem and i do the same but nothing..
I tried to delete xposed installer and my phone stuck..
What can i do?
Edit:It s opened but i can t touch my screen.I try to put my password and i can t..

tauio111 said:
Download this rom for example (Removed to allow posting - faye2thesky)
Extract the .z7 and run the flash_all.bat, this scripts flashes the rom via fastboot and you should get your device back up and running again. And from there you can update to a newer firmware version without problems.
If the bat doesn't work try this:
boot to fastboot
fastboot flash system system.img
fastboot flash cust cust.img
fastboot reboot recovery
Wipe cache and dalvik cache in twrp
Click to expand...
Click to collapse
Heya Tauio111, I'm having the same problem as onetree and I've been frying my mind over this for the past 4 days before I came across your solution. I found that your link is no longer working, may I ask what that ROM is and where else I may find it? Thanks!

faye2thesky said:
Heya Tauio111, I'm having the same problem as onetree and I've been frying my mind over this for the past 4 days before I came across your solution. I found that your link is no longer working, may I ask what that ROM is and where else I may find it? Thanks!
Click to expand...
Click to collapse
A way that may help (i've done it with boot&recovery images). Using this tool http://forum.xda-developers.com/showthread.php?t=2433454 , might give you the *.img files necesary for flashing the stock rom through fast boot. All you need is to follow the instructions on the tool and have a stock rom (update.app file type), and some knowledge on how to use the fastboot.

Hi Guys,
I kinda did the same thing here.
I accidently wiped my system with TWRP v2.6.3.7
I also have a huawei ascend p6 u06
I didn't realize i never copied a rom to my device so i don't know how to install.
I can't seem to be able to use adb or fastboot and my device is not picked up by windows (8.1), it just says removable disk in my computer.
and under device manager it says P6-U06 under unknown devices.
I have tried to install a bunch of different drivers to attempt something but no luck.
Please help me.