[Q] Note 2 Cracked Screen... Some questions - Sprint Samsung Galaxy Note II

So I was walking yesterday and managed to drop my phone. While it was in a case, apparently that was enough to essentially shatter the screen. It looks like the digitizer is ok, because I can still use it just fine. I've looked around and I can go 2 routes. Either I can replace the glass which covers the digitizer or I can replace the whole assembly. Obviously the glass screen is cheaper, so I'd like to try that route first.
My first question is: Has anyone actually done this before? Could you give me your thoughts and any gotchas?
Secondly, does anyone know if there is a difference between the glass for a N7100 vs the SPH-L900? The reason why I ask is that there are multiple listings on ebay for the N7100 glass but significantly less for the SPH-900. I wonder if they are different dimensions or maybe have different properties of some sort.
Thanks guys!

Tharkys said:
So I was walking yesterday and managed to drop my phone. While it was in a case, apparently that was enough to essentially shatter the screen. It looks like the digitizer is ok, because I can still use it just fine. I've looked around and I can go 2 routes. Either I can replace the glass which covers the digitizer or I can replace the whole assembly. Obviously the glass screen is cheaper, so I'd like to try that route first.
My first question is: Has anyone actually done this before? Could you give me your thoughts and any gotchas?
Secondly, does anyone know if there is a difference between the glass for a N7100 vs the SPH-L900? The reason why I ask is that there are multiple listings on ebay for the N7100 glass but significantly less for the SPH-900. I wonder if they are different dimensions or maybe have different properties of some sort.
Thanks guys!
Click to expand...
Click to collapse
Hunt down a true OEM screen.

Get the screen and digitizer oem all in one. Super easy to change. Don't even attempt to replace just the screen. Should set you back <200
Sent from my HTCONE using xda premium

Skip the screen and buy a full screen and digitizer. Make sure to buy oem. Doing just the glass will only be money down the drain. Its not worth the money or hassle. Considering the most lukely outcome will either be dust or something behind the glass. As well as damage of the digitizer. I bought a replacement screen and digitizer combo. Didnt even need to watch a video or anything and it was my first install on any phone. Just remember to remove your sd card
Sent from my SPH-L900 using Tapatalk 2

Any difference between a sprint and verizon n2? My friend just broke her Vn2 glass and asked if I could fix it......I'm assuming they are roughly the same just thought I'd ask before I accept her challenge.....lol

i replaced just the screen on my Note2. Took about 2 hours but it worked. The new screen isn't as good as the OEM but for $22 vs $200 i can live with it. I do have a slight bubble in my screen that is noticeable only when the phone is off.

Related

Nexus i9250 Screen replacement

Hello to all. I did my fair bit of research on this forum about a screen replacement for the International version of Galaxy Nexus but could not find any suitable solution to an Indian user. I got my Nexus from Amazon and lost my screen in a pretty harsh fall. There are cracks developed at the top of the fortified glass and I could not find any screen replacements in my city/country so far.
I would like to know if any of you have replaced the i9250 screen anywhere outside the U.S and if so, what are the reliable options available? Singapore perhaps (Pretty close to India), anyone know of any place there?
Please do help if you can, I'd be much obliged.
Me too ;(
yessae said:
Hello to all. I did my fair bit of research on this forum about a screen replacement for the International version of Galaxy Nexus but could not find any suitable solution to an Indian user. I got my Nexus from Amazon and lost my screen in a pretty harsh fall. There are cracks developed at the top of the fortified glass and I could not find any screen replacements in my city/country so far.
I would like to know if any of you have replaced the i9250 screen anywhere outside the U.S and if so, what are the reliable options available? Singapore perhaps (Pretty close to India), anyone know of any place there?
Please do help if you can, I'd be much obliged.
Click to expand...
Click to collapse
Hmm i cant help but i am in the same position... I bought a screen (only) from this store on ebay "easyworldwidetrading" and even he doesnt know how to replace it! Any ideas anyone?? Nothing on youtube i can find... still got a cracked screen (phone works fine tho... I just tell people its a 'crack' app I cant uninstall...)
You may have to order a screen internationally. Check Amazon and
eBay.
Also, make sure that when you buy a screen the screen you buy is specifically for your device (GSM).
http://www.youtube.com/watch?v=kp6e5w2jkk4&feature=youtube_gdata_player This is video may be able to help you replace your screen.
Sent from my Galaxy Nexus using Tapatalk 2
infazzdar said:
You may have to order a screen internationally. Check Amazon and
eBay.
Also, make sure that when you buy a screen the screen you buy is specifically for your device (GSM).
http://www.youtube.com/watch?v=kp6e5w2jkk4&feature=youtube_gdata_player This is video may be able to help you replace your screen.
Sent from my Galaxy Nexus using Tapatalk 2
Click to expand...
Click to collapse
Are you absolutely sure the cdma nexus screen won't fit in the gsm version?
MrSmileyJr said:
Are you absolutely sure the cdma nexus screen won't fit in the gsm version?
Click to expand...
Click to collapse
Confirmed.
Do a search, it's out there.
did anyone tryed to change only the glass to a nexus? i've read some articles on xda over changeing the outer glass to i9000.
I have other question: the outer glass isn't glued to the whole digitizer? will i damage the digitizer if i try removing only the glass?
ovu85 said:
I have other question: the outer glass isn't glued to the whole digitizer? will i damage the digitizer if i try removing only the glass?
Click to expand...
Click to collapse
Yes to both. The original screen replacement come as a whole package, so you basically switch the internals to the new case+screen.
ovu85 said:
did anyone tryed to change only the glass to a nexus? i've read some articles on xda over changeing the outer glass to i9000.
I have other question: the outer glass isn't glued to the whole digitizer? will i damage the digitizer if i try removing only the glass?
Click to expand...
Click to collapse
if you are not very careful, yes.
I repair cell phones a side job. Screen replacements are my specialty. I haven't personally done a GNex but if its anything like the S2, it can be done. The key is patience and attention to detail. When I do screens like those, I budget an hour and a half for time to remove it. Its better to take a few breaks and double check your work than drop $150 on a replacement LCD because you were in a rush.
That brings my to my second point. The worst thing that will happen is you crack your LCD, so it can be fixed. You won't break it beyond repair. But don't try it unless you are ready to spend the extra money *IF* you mess up.
THANK'S for the advices
@ rudeguy: can you be more specific, like where exactly do you start from removing the glass, do you aply heat to a small are and the remove, what tools do you use? once again, thank's in advance!
PS:how does the digitizer stuck's to the glass? wown't i allso remove the digitizer when i'll remove the glass?

I9250 glass on i515?

I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I remember seeing that thread as well, I tried to find it, but could not.
justbecuz123 said:
I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
Click to expand...
Click to collapse
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
707BeastMode707 said:
I remember seeing that thread as well, I tried to find it, but could not.
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Are we talking about the glass or the whole display? It makes a big difference. Assuming all 3 displays are the same (i9250, L700, I515), the problem is separating the display from the frame plate. Its very difficult and you can crack it very, very easily if you try to remove it. The cheaper GN LCD's on eBay are from working units and those already have the frame plate attached to it. The only way to remove it is to use a heat gun and apply it on the top and bottom front areas (as well as the sides). The apply heat to the back frame plate to loosen up the adhesive in the mid section of the screen. Then, slowly and I mean very, very slowly try to pry it open using a thin blade. Start from the top and work your way down. You should stop if you meet too much resistance and reapply heat. Like I said its a pain in the ass and not for the timid. I got to successfully remove an LCD from a frame for a Galaxy S (i500) not too long ago, its a similar in process as the GNex
I also tried to remove a L700 LCD (cracked glass) from a frame a while back and cracked it even more. I know what I did wrong and I think I wont make that mistake again. My mistake was that I did not know the exact location of the adhesive and applied too much heat in the front. Another mistake was that I thought I could remove the front glass from the digitizer. Now I know this is almost impossible and I don't know how people can buy front lenses without using some type of special tools (a true hot air bga station for instance) or a technique that I'm not aware of.
So, that's my long rant right there. I would really appreciate if any of you can confirm that any all 3 displays are the same (i9250, l700, i515). If it is then I would dare to try it out and take some pictures in the process if all goes well.
What about the oven?
I used to be into cars, and it was popular to smoke the headlamps on Nissans. They also have a lot of glue in them, and it was recommended to put em in an oven lol.
I'm sure it would get hot enough to loosen the screen, but 400 degrees may break something else in the process...
Sent from my Galaxy Nexus using xda premium
Did anyone ever find the answer to this question? I am wondering the same thing.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
You can't use the i9250 screen on the i515. The battery metal thingies and the vibration thing are in different places.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
I have asked a bunch of eBay sellers for the last few days and have gotten mixed responses... I don't think that most of them get that I am talking about separating the display from the front case/plate. One guy told me that the digitizer/LCD combo is interchangeable from the i515 and i9250, but it won't work on the L700. One guy told me that he thought that the entire assembly including the front plate were the same between the L700 and i515. Several have said that they are model specific, but I don't think that most of them realized that I am not expecting to use the front plate from an L700 if i9250 on the i515...
It doesn't seem like Samsung would have a different display for each model. I can see the plates and cases being different because some of the other parts are different, but it seems like the LCD panel and the glass should be the same for each model. To me all of the screen connectors look the same from the pics I've seen...
Edit- I just found this online store that indicates they are the same screens http://www.globaldirectparts.com/OEM-Galaxy-Nexus-L700-LCD-Digitizer-Assembly-p/smsng6115350-qs.htm
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post.
Click to expand...
Click to collapse
Finally found the post that you are referring to (http://forum.xda-developers.com/showthread.php?t=1780491). Sounds like he ran into problems because he tried to use the i515's front housing on the i9250. I think if he had removed the screen from the frame and re-used the frame that was original to his phone he would have been fine. It looks like it takes some heat and care to do that, but it looks do able.
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
MrAreCool said:
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
Click to expand...
Click to collapse
L700 screen (not including frame) worked on my i515. Details here.
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
perusmuro said:
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
Click to expand...
Click to collapse
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
MrAreCool said:
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
Click to expand...
Click to collapse
I have found few videos where that glass is possible to remove.
http://www.youtube.com/watch?v=JlfO6TUj1DQ
But I think that I would buy that whole set and change that. But what is the best place to buy that? So I can real deal.
Ok guys, just wanted to confirm that front glass for the L700 and GT-i9250 the same. And I assume that i515 as well.
I got for repair Nexus Sprint (L700) with cracked front glass but then was surprised that glass for L700 on ebay about $15 and the same glass for i9250 less then $10. Not big deal but anyway.. So I bought the glass for i9250 and it fits great as original.
Good luck!)
When the purchase of parts and mobile phones are not matched, the proposed replacement.

[Q] Screen replacement

Hello All,
Just recently dropped my screen for AT&T Samsung Galaxy Note 2. The phone still works but has cracks everyone. I was wondering if anyone has attempted to change just the screen itself, if so, where did you buy the screen from and what tools did you use? Also, what is the metal frame around the phone called and is it possible to get it replaced? Thank you and have a nice day!
wangasore said:
Hello All,
Just recently dropped my screen for AT&T Samsung Galaxy Note 2. The phone still works but has cracks everyone. I was wondering if anyone has attempted to change just the screen itself, if so, where did you buy the screen from and what tools did you use? Also, what is the metal frame around the phone called and is it possible to get it replaced? Thank you and have a nice day!
Click to expand...
Click to collapse
If you are talking about the glass then I just replaced mine about a week ago. I actually ordered a replacement in white instead of the grey that I have. I used a hair dryer, hobby knife kit (only to start the edges), and the tools that came with the glass. It cost about $30 and an hour of your time. The only problem I had was getting the glass to stick with the old tape. A good reference are the videos for replacing the Galaxy S3 glass.
Do not push to hard when putting the new screen in place, you will break the digitizer if you do. I did find that if you have a completely broken screen and its showing black, the s-pen seems to still work fine and can make the phone function. I am assuming that the 11pin port will also push video to a tv with the screen broken and the phone can be used that way also if needed (will test and let you know).
Nate8315 said:
If you are talking about the glass then I just replaced mine about a week ago. I actually ordered a replacement in white instead of the grey that I have. I used a hair dryer, hobby knife kit (only to start the edges), and the tools that came with the glass. It cost about $30 and an hour of your time. The only problem I had was getting the glass to stick with the old tape. A good reference are the videos for replacing the Galaxy S3 glass.
Do not push to hard when putting the new screen in place, you will break the digitizer if you do. I did find that if you have a completely broken screen and its showing black, the s-pen seems to still work fine and can make the phone function. I am assuming that the 11pin port will also push video to a tv with the screen broken and the phone can be used that way also if needed (will test and let you know).
Click to expand...
Click to collapse
How hard was it to do a replacement on the screen glass itself? and is it easy to do a bezel replacement?
Nate8315 said:
If you are talking about the glass then I just replaced mine about a week ago. I actually ordered a replacement in white instead of the grey that I have. I used a hair dryer, hobby knife kit (only to start the edges), and the tools that came with the glass. It cost about $30 and an hour of your time. The only problem I had was getting the glass to stick with the old tape. A good reference are the videos for replacing the Galaxy S3 glass.
Do not push to hard when putting the new screen in place, you will break the digitizer if you do. I did find that if you have a completely broken screen and its showing black, the s-pen seems to still work fine and can make the phone function. I am assuming that the 11pin port will also push video to a tv with the screen broken and the phone can be used that way also if needed (will test and let you know).
Click to expand...
Click to collapse
You replaced the glass for the Note 2? Yes I am just talking about the glass itself. Do you have a link to where you bought the item and any link to videos you used to assist you in replacing the glass? Thank you so much for all your help!
wangasore said:
You replaced the glass for the Note 2? Yes I am just talking about the glass itself. Do you have a link to where you bought the item and any link to videos you used to assist you in replacing the glass? Thank you so much for all your help!
Click to expand...
Click to collapse
I purchased the glass off of ebay, I cant post a link due to not having enough post here, but just search "galaxy note 2 replacement glass"
I looked at a bunch of Galaxy S3 glass replacement videos. just search "s3 glass replacement" on youtube.
It is time consuming, I used a hair dryer to be safe because heat guns get too hot if not careful.
I did get a chance to test if the 11pin still pushed video to a tv with a broken screen (using an MHL adapter). It did not for me. I plugged a phone in with a broken digitizer that the s pen still worked on and would let me make calls from. The phone is still function able, just no picture on the screen (working in the dark with the s-pen). Nothing showed up on the tv screen. I plugged another note 2 in to verify and the other note 2 pushed video just fine.
What's the easiest way to tell if I just need to replace the glass versus the entire digitizer?
Glass replacement
Ok for every thread on the internet the digitizer is NOT part of the glass. The glass is just that......glass. Stop calling it a digitizer these are not iPhones!!!!!! The digitizer is laid on top of the amoled and has a connector that runs under the display and plugs in there with a flip type switch connector. The glass can be removed with heat approx. 160 deg with a heat gun on low and keeping track of the temp with a infrared thermo. I've done this a few times now be careful with white as these tend to break easier than the grey not sure why laminate must be weaker. Takes 45mins to do. You can buy the glass for approx. $25 shipped be careful near the bottom with the button flex they are glued on. You must reuse your speaker trim and button trim also. I have only 1 single question can you buy a replacement digitizer by itself without having to buy the amoled? Anyone know and how much they are please point me to one for the i317m.
Why the are you answering a 3 month old thread?
Op says he dropped his screen...lol
Sent from my SAMSUNG-SGH-I317 using xda premium
Better late than never. ...imho...lol

Screen replacement

Hey I just recently broke my screen and I bought my phone last july. Its not completely broken but its shattered most of the screen and its incredibly annoying. Is there anyway I could get a new phone or get a cheap screen replacement within 30-50$ range? Or should I just go ahead and get a new phone?
Sent from my SGH-I747 using xda premium
Tyler.Boston1 said:
Hey I just recently broke my screen and I bought my phone last july. Its not completely broken but its shattered most of the screen and its incredibly annoying. Is there anyway I could get a new phone or get a cheap screen replacement within 30-50$ range? Or should I just go ahead and get a new phone?
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
If the digitalizer isn't damaged, replacing the glass only is cheap and easy. Look it up :good:
BWolf56 said:
If the digitalizer isn't damaged, replacing the glass only is cheap and easy. Look it up :good:
Click to expand...
Click to collapse
How would I tell if the digitilizer is broken? It may look just like the glass is broken. If I didn't have my screen protector on I'm pretty sure it would fall apart
Sent from my SGH-I747 using xda premium
Tyler.Boston1 said:
How would I tell if the digitilizer is broken? It may look just like the glass is broken. If I didn't have my screen protector on I'm pretty sure it would fall apart
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
If the screen usable? Any color/light bleed? Or color distortion/fading?
BWolf56 said:
If the screen usable? Any color/light bleed? Or color distortion/fading?
Click to expand...
Click to collapse
Oh ok well then its still working
Sent from my SGH-I747 using xda premium
Tyler.Boston1 said:
Oh ok well then its still working
Sent from my SGH-I747 using xda premium
Click to expand...
Click to collapse
Check out this thread for replacing your screen
http://forum.xda-developers.com/showthread.php?t=1945494
I highly recommend against trying to replace just the glass. That is what I tried to do, but the LCD is glued to the digitizer which is glued to the glass. I didn't use enough heat and though I got through the edge tape holding the glass to the frame, I shattered the digitizer and LCD as well as busted through the menu buttons.
If you think you can do it, go for it. Not real tool intensive, but there will be lots of heat and the success rate is probably 50/50.
The next step from that is to replace the whole LCD/DIGITIZER/GLASS. But that will set you back around $200. Same process, but you pretty much scrape the glass, digitizer and LCD from the metal frame. Lots of effort, lots of time, and little pieces of glass flying everywhere.
For about the same price, get the FRAME/LCD/DIGITIZER/GLASS asssembly. It only requires removing a few screws, unhooking a couple of cables, and replacing the hole front end. It can be done with care in about 15 minutes.
If you do that, be sure you get the right model number. If you are on AT&T in the US, you'll need the i747. The i9300 may come up a few bucks less, but it's not compatible. Color doesn't matter - you can change now, if you want.
The biggest disadvantage of removing the glass only is the risk of getting dust inbetween the LCD and the glass front. With the other two methods, the LCD/DIGITIZER/GLASS are already fused together. However, if you pull it off, no one will ever know you messed with it, and the warranty cheat won't be tampered with as it will be with a frame replacement.
According to the other post, you are still 13 months from an upgrade. That means around $450 to replace your S3 and $630 if you want to go the S4. For less than half that, you can get the frame replaced. I might even suggest that once you replace the frame, you spend that $10 to replace the glass and try it without any fear of consequences on the one you remove. If you do it well, you might could sell that assembly for $150-$200.
Good luck!
i9300 screen (no frame) will fit i747 frame
can you advise if a i9300 screen (no frame) will fit i747 frame? Mine is 747, I can see lots of posts on Ebay for screens with both 9300 and 747 compatible. Want to make sure before order.
k2lc said:
can you advise if a i9300 screen (no frame) will fit i747 frame? Mine is 747, I can see lots of posts on Ebay for screens with both 9300 and 747 compatible. Want to make sure before order.
Click to expand...
Click to collapse
Lcd, digitizer, and glass are all identical except color. Once you see the word "frame", the model matters.
I just recently did this successfully. The key is a good source of heat and patience. I used a heat gun and it took me about thirty minutes to do. There are screens you can order that come with the little tools to use. Start heating it slowly and use the tools to take the glass off. Heat it until its relatively easy to get the glass off but do not over heat it! Keep going until all the glass is off. Once its off, apply some sticky tape (or you can use the tape that was already on the phone if you don't destroy it) and it will be good to go. Make sure that you take the protective paper off the glass you ordered.
Should you have any issues feel free to PM me.
Sent from my SAMSUNG-SGH-I747 using xda premium

[Q] Any General Tips Before Replacing a Cracked Screen?

I cracked my screen a while back and every time I look at it I get sad. Now recently I found on YouTube that it actually seems fairly simple to replace your screen yourself. I'm just wondering if anyone else has replaced their own and has any tips before I order the parts.
You can replace just the glass but the correct way to do it is replace the complete digitizer glass set. There is a special adhesive film which bonds the digitizer to the glass and you can never duplicate it as if you where doing the complete set up.
You will notice it more when using your device in the sun, the screen will be very difficult to see
Have a great day!
Dont do the glass only fix. Spend the extra money and get the front half of the phone and re-mount everything to it.
atleast they've dropped in price a bit, use to be a 250 dollar fix, now its around 150.
Just make sure youre getting the one thats compatible with Sprint. Theres a slightly almost unnoticeable size difference between verizon/att/sprint models and sprint motherboards will not fit in to att/vzw frames. IDK Why they did this.
Have a pro do it. I learned that back on my iPhone 3g and buy OEM not a eBay knock off that breaks easier.

Categories

Resources