re-use display/screen with housing swap? - T-Mobile, Samsung Galaxy SIII

search is disabled/not working and i need an answer asap, sorry if this has been covered before!
i recently cracked the glass on my s3; it wasn't TOO bad and the display/screen itself wasn't cracked at all. the glass/digitizer has been removed but it seems as though the display is glued the EFF onto the chassis. i purchased an entirely new housing/chassis on ebay (wanted a color change ) and was wondering - how can i pull the display off the old chassis without damaging it? would using a blow dryer work well enough to pull it off, then re-adhere it to the new chassis? if so, i'm assuming it'd be safer to blow dry that area from the back/not directly onto the display itself? or is it too delicate to even attempt?
thanks for any/all responses!
rob

ce_rob said:
search is disabled/not working and i need an answer asap, sorry if this has been covered before!
i recently cracked the glass on my s3; it wasn't TOO bad and the display/screen itself wasn't cracked at all. the glass/digitizer has been removed but it seems as though the display is glued the EFF onto the chassis. i purchased an entirely new housing/chassis on ebay (wanted a color change ) and was wondering - how can i pull the display off the old chassis without damaging it? would using a blow dryer work well enough to pull it off, then re-adhere it to the new chassis? if so, i'm assuming it'd be safer to blow dry that area from the back/not directly onto the display itself? or is it too delicate to even attempt?
thanks for any/all responses!
rob
Click to expand...
Click to collapse
YouTube is your friend with situations like these, you should be fine with a blow dryer and for most people its way too delicate to attempt. You just have to have a lot of patience.
Which color are you going with?
Sent from my SGH-T999 using xda premium

ce_rob said:
search is disabled/not working and i need an answer asap, sorry if this has been covered before!
i recently cracked the glass on my s3; it wasn't TOO bad and the display/screen itself wasn't cracked at all. the glass/digitizer has been removed but it seems as though the display is glued the EFF onto the chassis. i purchased an entirely new housing/chassis on ebay (wanted a color change ) and was wondering - how can i pull the display off the old chassis without damaging it? would using a blow dryer work well enough to pull it off, then re-adhere it to the new chassis? if so, i'm assuming it'd be safer to blow dry that area from the back/not directly onto the display itself? or is it too delicate to even attempt?
thanks for any/all responses!
rob
Click to expand...
Click to collapse
Just like the Note II and perhaps other Samsung phones...it is Painfully difficult to pull this off. Not impossible, just very difficult.
Check youtube, there's videos of people doing it there, but I warn you, it won't be easy. Blow dryer may not work, it may need a heat gun.
http://www.youtube.com/watch?v=aZuiCsAtThw

707BeastMode707 said:
YouTube is your friend with situations like these, you should be fine with a blow dryer and for most people its way too delicate to attempt. You just have to have a lot of patience.
Which color are you going with?
Sent from my SGH-T999 using xda premium
Click to expand...
Click to collapse
and, as you can imagine (or not, given your response), i've gone through every possible tear-down, glass removal, pull-this-*****-apart video on youtube. nothing speaks of removing the display itself, ONLY the glass and/or digitizer. i've replaced the glass/digitizer on other phones before, but i've yet to tackle the display. because it's (seemingly) stuck onto the chassis a lot stronger than the glass, i figured i'd ask.
so again, if anyone has actually removed the display and NOT the glass (or has a video/link/walk-through i may have overlooked), i'd greatly appreciate it.

crs77 said:
Just like the Note II and perhaps other Samsung phones...it is Painfully difficult to pull this off. Not impossible, just very difficult.
Check youtube, there's videos of people doing it there, but I warn you, it won't be easy. Blow dryer may not work, it may need a heat gun.
http://www.youtube.com/watch?v=aZuiCsAtThw
Click to expand...
Click to collapse
guys, i'm not talking about the glass! i'm talking about the DISPLAY - what's UNDER the glass. lol

I think this is what you're looking for:
http://videos-with-links.info/watch/_70-W9JjVjg/galaxy-s3-screen-replacement-frame-change.html

crs77 said:
I think this is what you're looking for:
http://videos-with-links.info/watch/_70-W9JjVjg/galaxy-s3-screen-replacement-frame-change.html
Click to expand...
Click to collapse
thanks, but i've seen that one. the display is attached to everything (what he shows in the first few seconds, glass/digitizer/display already assembled). my glass/digitizer broke and has been removed, display still being on the housing itself and not cracked or ripped. the difference in price is $18 vs $178 for glass/digitzer and glass/digitizer/display, respectively. just wanted to see if anyone has replaced them all, but separately, saving over $150...
doesn't seem like that's been tried or done, though. i guess it wouldn't HURT to try - if successful, it'll have only cost $18. if unsuccessful, i'll have to spend the $178 anyway...can't hurt? i'll give it a try soon and report back.
thanks for the help either way, gentlemen!

btw, the reason for wanting to remove/re-adhere the display has to do with the fact that everything (sans broken glass, obv) will be swapped from one housing to another - going from white to grey, a complete color change. that's why i'm not just replacing the glass, in this case - if anyone was wondering

Please read forum rules before posting
Questions and help issues go in Q&A
Thread moved
Thank you for your cooperation
Friendly Neighborhood Moderator

Related

[Q] LCD Replacement???

Hi guys, I got my hands on a MT4G with a broken LCD.
First Q, is it worthy getting a replacement off cheapbay? What other options are there?
Second Q, is it hard to replace it? Is it possible to do it myself?
Thanks for your advise...
I haven't replaced an LCD myself but I am looking to replace a digitizer for my wife's phone.
Someone posted up this link for me in another thread I started.
http://www.ebay.com/itm/FULL-LCD-DI...984?pt=LH_DefaultDomain_0&hash=item2a12834fe0
This should take out the hard part of disassembling the digitizer from the lcd and reattaching and the adhesive itself.
It's the complete the front housing, digitizer AND LCD in one. Already assembled.
I haven't ordered it myself yet but I AM tempted. Especially after watching some of these disassembling videos.
Let me know what you decide and how it worked out.
Just PM me.
Thanks bro and good luck.
Thanks a lot, I will check it out, the adhesive part really has me in doubt.
I've replaced the LCD without the digitizer attached and you are both correct. It can be done but the finished product is not factory quality. I looked at the ebay part posted in the link and that would be the way to do it. Otherwise you have to use a hair dryer to heat the glue and its not fun.
If you are not familiar with taking electronics apart look for a video tutorial via google; I used one to take the MT4G apart. Also label the screws as they come out by drawing the phone on a piece of paper and placing the screw accordingly on the paper. Makes assembly much easier!
Hope you take on the challenge and good luck.
allenmehrer said:
I've replaced the LCD without the digitizer attached and you are both correct. It can be done but the finished product is not factory quality. I looked at the ebay part posted in the link and that would be the way to do it. Otherwise you have to use a hair dryer to heat the glue and its not fun.
If you are not familiar with taking electronics apart look for a video tutorial via google; I used one to take the MT4G apart. Also label the screws as they come out by drawing the phone on a piece of paper and placing the screw accordingly on the paper. Makes assembly much easier!
Hope you take on the challenge and good luck.
Click to expand...
Click to collapse
Yeah my only thing about ordering this complete assembly is that my wife's phone has the SO screen and I don't want to replace with an SH, which I'm sure that part is going to be. (99.99% sure)
Add to that, she doesn't even need a new LCD and the digitizer alone is just 25 bucks.
Decisions, decisions.
nguyendqh said:
Yeah my only thing about ordering this complete assembly is that my wife's phone has the SO screen and I don't want to replace with an SH, which I'm sure that part is going to be. (99.99% sure)
Add to that, she doesn't even need a new LCD and the digitizer alone is just 25 bucks.
Decisions, decisions.
Click to expand...
Click to collapse
I have to clean the dirt out between my digitizer and lcd! Can't tell you how annoying that is. Suppose someone could do a better job resealing it... It would be nice if a digitizer/lcd kit came with new adhesive.
http://www.papadigitals.com/advance...uch+4g&sgmid=aa6a532f59b343f82afc0aaa2d55c02d
I saw lcd screen and touch screen digitizer for HTC mytouch 4G there.
I've been taking electronics apart since I was 7 tears old. The MyTouch 4g finally beat me.
There are a lot of really delicate connectors that break easily. Be careful
dr_tracker said:
is it worthy getting a replacement off cheapbay? What other options are there? Second Q, is it hard to replace
Click to expand...
Click to collapse
You'd better to buy non-working phone (maybe from ebay) and make one from two phones. You should have the screwdriver. Easy to replace.
It is not really hard i saw a vid on youtube just search it up super easy actually
I bought a digitizer LCD already together for like 75 and it wasn't too bad to exchange and put this new one in but when I powered the phone the bottom left of the screen didn't work and it impossible to take it back out of the silver bezel without breaking it so I sent it back to get my money and lost the bezel. Its not too hard but be careful take your time and don't pull or yank anything.
Sent from my SGH-T959 using xda premium
I replaced my digitizer. I agree, there are many delicate connectors, but nothing to be afraid of. You should watch the YouTube video over and over. Also, be careful not to push on the bottom buttons while taking it apart. This was the most frustrating thing because they wouldn't sit properly when reassembled. I took it apart 5 times before I forgot to detach the power ribbon and ripped it off! There are motherboards available to fix this, but saving it for another day.
Sent from my HTC Glacier using Tapatalk
That's funny that's the same exact thing I did pulled the power ribbon right out so I just said screw it and just bought a new phone on eBay
Sent from my SGH-T959 using xda premium

Broken Screen - Which part should i buy?

My GF broke the screen on her Droid Incredible, Verizon insurance wants $100 to replace it, so not sure it is worth it for this phone, and she has a few months left before her upgrade is ready. If i am going to try to fix it for her, can anyone with experience tell me what parts specifically I would need? The LCD seems fine, so i would think i can replace just the digitizer, which i can get on Amazon for $16
http://www.amazon.com/Incredible-Sc...ement-Adhesives/dp/B005TGX6X8/ref=pd_cp_cps_0
They also sell with front housing
http://www.amazon.com/Touch-Screen-Glass-Digitizer-Incredible/dp/B005L0XRRM/ref=pd_cp_cps_1
any tips which to buy or what to do etc?
Why would one/How does one know if they need to replace the LCD as well?
All touch aspects of phone working fine and seems like it's just the glass cracked.
Dillsnik said:
My GF broke the screen on her Droid Incredible, Verizon insurance wants $100 to replace it, so not sure it is worth it for this phone, and she has a few months left before her upgrade is ready. If i am going to try to fix it for her, can anyone with experience tell me what parts specifically I would need? The LCD seems fine, so i would think i can replace just the digitizer, which i can get on Amazon for $16
http://www.amazon.com/Incredible-Sc...ement-Adhesives/dp/B005TGX6X8/ref=pd_cp_cps_0
They also sell with front housing
http://www.amazon.com/Touch-Screen-Glass-Digitizer-Incredible/dp/B005L0XRRM/ref=pd_cp_cps_1
any tips which to buy or what to do etc?
Why would one/How does one know if they need to replace the LCD as well?
All touch aspects of phone working fine and seems like it's just the glass cracked.
Click to expand...
Click to collapse
I am no expert, but it would seem that if anything under the glass was broken, you would need to replace the lcd (that is, if you could see the lcd "leaking" or being distorted)
Sent from my ARCHOS 80G9 using Tapatalk 2
Nothing under the screen seems broken.
Anyone done this?
Sent from my SAMSUNG-SGH-I717 using Tapatalk
Dillsnik said:
Nothing under the screen seems broken.
Anyone done this?
Sent from my SAMSUNG-SGH-I717 using Tapatalk
Click to expand...
Click to collapse
Unfortunately I have had the pleasure of replacing my digitizer twice. You definitely wanna buy it WITH the frame or housing. The adhesive is like industrial strength and you will end up breaking the original anyways when trying to remove the digitizer from it. I have to warn you that doing this repair yourself will void your warranty. Make sure the digitizer you get comes with the tools required to get the phone apart. You can get this as a package on eBay fairly cheap too. There are about 3-4 circuit strips that will have to be removed from their clips, don't be intimidated by them, but be gentle. Your first time is gonna take you a while, just be patient. If you need to do it a second time, its gonna be a breeze. PM me if you have any concerns during your repair.
yea get a digitizer also,
I had the same thing happen to me, it was a pain but there are a few videos on youtube
that should help you through it, though it doesn't sound like its that bad
Definitely go with the digitizer and housing replacement together. Bottom line, it will make your life so much less of a headache while replacing it.
Sent from my ADR6300 using XDA
I just replaced mine this weekend. I attached some before, during, and after pictures...
These were the guides that I followed:
Part 1: http://www.youtube.com/watch?v=TfpPS7oO4Q8
Part 2: http://www.youtube.com/watch?v=GJMAmKpk20c
Personally, I went with just the glass/digitizer (your first link) and it went fine. The glass is difficult to get out of the housing, but it's not that bad. It probably took me 20 minutes to get the old glass out, maybe 5 minutes of cleaning goo from the old adhesive, and probably another 5 minutes to put the new glass back on.
Some Tips:
The pry tool that comes with it is very cheap. I would suggest using it sparingly until you get to the LCD panel extraction and glass removal. You want it to be as in good of condition as can be when you get to those later steps.
Use a blow-drier to heat up the adhesive, and get it to the point where you almost cant touch it. I used some yellow kitchen gloves so I could get it a little hotter and still be able to hold it. I used a combination of my hands and the pry tool and worked mostly along the sides and top first, then separated the bottom last.
The guy in the youtube videos uses glue, but you shouldn't need that. It comes with pre-cut adhesive strips, which work great. One word of caution though... The sheet that they come on is scored for you, but I suggest using an x-acto to cut them out. This is especially important for the thin rectangle that goes around the outside of the glass. You really don't want to pull on that... you don't want it to get stretched or twisted. Summary: the strips work great, just be careful extracting them from the sheet they come on, and placing them on the phone.
Don't forget to get the red earpiece grill off of the old glass before throwing it away. You'll need to super glue that back onto the housing, but it's really easy to see where it goes. This should be the only thing you need glue for.
When removing the glass, cleaning up gunk from the old adhesive, and applying new adhesive, be careful of the electronics at the bottom for your capacitive buttons... you definitely don't want to harm or obstruct those.
This should probably go without saying, but make sure not to touch the inside of the new glass, or the LCD panel. You don't want fingerprints or dust inside the phone. Even if you don't touch it, I would still give it a shot of compressed air right before putting it in, just to make sure there's no dust.
I would say that it's probably worth the extra $10-12 bucks to get it with the housing already included, but it's definitely not necessary if you want to save a little money. As I said above, it only took me about a half hour to get the old glass out and the new glass in, and from what it sounds like, there is still some effort involved even if you get it with the housing (moving the circuitry from the old one). I wouldn't worry about breaking the frame... it's pretty strong. If you break it, you're doing it wrong. Although, if your frame has some scrapes and other assorted road rash on it like mine does (see first picture), then maybe you might want a new one anyway. Another consideration... the reviews on Amazon for the one without the housing are much better, but that could just be because of people who don't know what they're doing... who knows.
If you have any questions, I'd certainly be willing to help... PM me if you want. And if I'm going to be around when you go to actually do the replacement, I can give you my gchat address in case you have any questions during the process.

How to replace just the glass lens on the at&t galaxy s3

Pretty much all you need in the title. I wanted to know how to do this mainly because it's cheaper then buying a lCD digitizer combo and because I can't find a guide anywhere else. Any tips and tricks on how to do this should be well appreciated and any guides. Thanks in andVance for anyone's help.
Sent from my SAMSUNG-SGH-I747 using xda premium
Backslash10 said:
Pretty much all you need in the title. I wanted to know how to do this mainly because it's cheaper then buying a lCD digitizer combo and because I can't find a guide anywhere else. Any tips and tricks on how to do this should be well appreciated and any guides. Thanks in andVance for anyone's help.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
I also have a cracked the screen, What my search result has come up with is the cost to replace the screen is ~$200CDN. Can you please keep me posted on what path you would be taking, might just follow
Replacing the glass from the actual screen is very hard and would require tons of technical know-how because the two are fused together.
Not recommended, even by experts.
Well I know it's extremely hard but I'm mainly looking for advise about it is all it decently help people out here.
Sent from my SAMSUNG-SGH-I747 using xda premium
Backslash10 said:
Well I know it's extremely hard but I'm mainly looking for advise about it is all it decently help people out here.
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
it's not possible to do. period.
Really I thought I could be done but took a lot of waiting and just the right heat and pressure.
Sent from my SAMSUNG-SGH-I747 using xda premium
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
Nice
Op
http://forum.xda-developers.com/showthread.php?t=1904554
it is very possible I have done 4 of them already...
http://forum.xda-developers.com/showthread.php?t=1890708
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
hahahah.....owned, should really atleast attempt to find out if what you are saying has any evidence to support it, or rebut it
dLo GSR said:
it's not possible to do. period.
Click to expand...
Click to collapse
I've heard its possible, just EXTREMELY difficult to manage.. I wouldn't.
Its entirely possible, as the multiple video's have shown. Although i haven't done it to the SGS3 yet, i will be soon. Cracked my lens the other day, replacement in the mail. I have also changed the screen's on several iphones (at my job) which us a similar method of gluing. It is made to be difficult by design...to keep people from attempting it and opting to send it in for repair. Of course when you do this, through samsung anyways, you are being charged for the entire led assembly and not just the lens.
dntesinfrno said:
Its entirely possible, as the multiple video's have shown. Although i haven't done it to the SGS3 yet, i will be soon. Cracked my lens the other day, replacement in the mail. I have also changed the screen's on several iphones (at my job) which us a similar method of gluing. It is made to be difficult by design...to keep people from attempting it and opting to send it in for repair. Of course when you do this, through samsung anyways, you are being charged for the entire led assembly and not just the lens.
Click to expand...
Click to collapse
Good to hear you did it at your job with iphones. Any idea what glue they use to bond the glass to the digitizer? I have searched and searched and cannot find anything. I have done several S3 so far and this is the one ingredient lacking for a complete repair. In terms of what it feels like while removing the old glue; it seems to be silicone based the way it comes up, you can roll it into little balls, it's is tacky and has that rubbery consistency.
Unfortunately, no idea what adhesive they use. Personally i would attempt what YellowGTO did first and simply heat the existing glue and see how it holds. Normally this should be enough to do the job, as you can imagine the stuff if pretty tacky. Especially if the lens fits as tightly as his in the video, its doubtful it will fall out even with the slightest remaining glue. If for whatever reason there isn't enough to firmly hold the screen in place i've used small dabs of liquid tape where necessary, or the thin 3M double sided tape would work also i suppose. In this case i usually wrap the device in a towel or shirt or whatever you have laying around and set something with some decent weight on top of it, screen side down on a flat surface, overnight to give the adhesive time to setup properly.
dntesinfrno said:
Unfortunately, no idea what adhesive they use. Personally i would attempt what YellowGTO did first and simply heat the existing glue and see how it holds. Normally this should be enough to do the job, as you can imagine the stuff if pretty tacky. Especially if the lens fits as tightly as his in the video, its doubtful it will fall out even with the slightest remaining glue. If for whatever reason there isn't enough to firmly hold the screen in place i've used small dabs of liquid tape where necessary, or the thin 3M double sided tape would work also i suppose. In this case i usually wrap the device in a towel or shirt or whatever you have laying around and set something with some decent weight on top of it, screen side down on a flat surface, overnight to give the adhesive time to setup properly.
Click to expand...
Click to collapse
Sure the outer frame is enough in most cases to hold it on, thats fine. But there is a side effect once all the glue is removed off the digitizer. There will a micro gap between the 2 when the original glue is removed. If you press the new glass hard enough, ( for example cleaning fingerprints like I often do against my shirt ) and it touches the digitizer, the phone freezes. You must then power off the screen, sleep button and then press power again to bring it up and then it will work again. Seems to be a recalibration process going on.
Maybe these 2 posts should be merged and I would certainly read the post below. Much more good info here on the subject...
http://forum.xda-developers.com/showthread.php?p=33056057#post33056057
Yea, i've been following several threads about lens replacement, even before i busted mine (jinxed myself?). I'd much rather have to deal with a 15 second reboot over possibly damaging the LED or worse using an adhesive that may not be transparent. I can live with the air gap, or even the 'invisible' smudges on my personal device...although if i were going to do this for profit obviously that would be unacceptable. 20 dollars and an hour of my time vs 200+ for the whole assembly or 125 for an insurance deductable..i can overlook imprefections . It would be interesting to find out exactly what substance they are using though.
EDIT - Just for SnG's i googled 'mobile screen glue' and this was the first result. http://www.alibaba.com/product-gs/523467689/Optical_Clear_Adhesive_for_touch_screen.html?s=p
While i'm sure its not the only product out there for this purpose, if this is any indication it won't come cheap..
dntesinfrno said:
Yea, i've been following several threads about lens replacement, even before i busted mine (jinxed myself?). I'd much rather have to deal with a 15 second reboot over possibly damaging the LED or worse using an adhesive that may not be transparent. I can live with the air gap, or even the 'invisible' smudges on my personal device...although if i were going to do this for profit obviously that would be unacceptable. 20 dollars and an hour of my time vs 200+ for the whole assembly or 125 for an insurance deductable..i can overlook imprefections . It would be interesting to find out exactly what substance they are using though.
Click to expand...
Click to collapse
Agreed it would be nice to find out what type of glue.
The phone breaks so easy i am surprised I have not heard of a Class Action Lawsuit... :silly:
here are instructions on replacing just the glass/screen
[HOW TO] [TUTORIAL] S3 Replace Cracked Glass Screen w/ YouTube Video
i replaced my screen took me about 50 mins with 2 people
XeoNoX said:
here are instructions on replacing just the glass/screen
[HOW TO] [TUTORIAL] S3 Replace Cracked Glass Screen w/ YouTube Video
i replaced my screen took me about 50 mins with 2 people
Click to expand...
Click to collapse
Very very nice!! :thumbup::thumbup:
Sent from my SCH-I535 using xda app-developers app
marcustaz said:
Very very nice!! :thumbup::thumbup:
Sent from my SCH-I535 using xda app-developers app
Click to expand...
Click to collapse
JUst did an even EASIER replacement for a cracked camera lens. I purchased this part from ebay :
http://www.ebay.com/itm/Blue-Housin.../271099346918?ssPageName=ADME:L:eek:C:US:3160
1) Turn phone off
2) Take off battery cover
3) Remove battery, SIM card, and SD Card
4) remove about 8 screws to remove the middle back place.
5) Remove middle back place carefully (There are still tabs holding it secure)
6) Place new middle back in place
7) Screw down
8) Replace battery, SIM card, and SD card
9) Replace battery cover
10) Power up phone!!
Took all of 10 minutes total. Flawless fix on my AT&T Samsung Galaxy S 3
Gentlemen and OP please update your original post to include this video. This is NOT to promote myself but from all the comments and feedback everyone has stated it is the most detailed and informative on You Tube on the glass replacement procedure. I also have separate videos on shattered glass replacement. Thanks and good luck.

I9250 glass on i515?

I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post. I would personally just recommend paying more for the i515 glass and knowing that everything will fit alright, rather than taking a chance on throwing your money away.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
I remember seeing that thread as well, I tried to find it, but could not.
justbecuz123 said:
I was not a happy camper when I dropped my phone at work this morning and shattered the glass around the front speaker on my vzw gnex. Digitizer and led display are fine, so I'm looking to buy a new glass panel for it. Unfortunately, all the panels I see on ebay except for two are for the gsm one, not the cdma one. I know the battery door won't fit between the two, but the glass should, right? In the pictures everything looks to be in exactly the same spot. The two for the i515 are considerably more expensive than the i9250,which is why I ask.
For the record, I did pretty good; I got my first gameboy color at 6 or 7,and being just a few months away from 21 now, this is the first mobile handheld device that I've ever broken a screen on.
Click to expand...
Click to collapse
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
707BeastMode707 said:
I remember seeing that thread as well, I tried to find it, but could not.
A user was able to replace the i9250 screen with the i515 screen, but from the post, it said he ran into a whole bunch of problems and that if you don't know what you're doing, you shouldn't waste your time.
I would just play it safe and buy the screen that goes with the phone, unless you really want to save money and try it out, but you might waste money if you damage the screen during the process.
Sent from my Galaxy Nexus using xda premium
Click to expand...
Click to collapse
Are we talking about the glass or the whole display? It makes a big difference. Assuming all 3 displays are the same (i9250, L700, I515), the problem is separating the display from the frame plate. Its very difficult and you can crack it very, very easily if you try to remove it. The cheaper GN LCD's on eBay are from working units and those already have the frame plate attached to it. The only way to remove it is to use a heat gun and apply it on the top and bottom front areas (as well as the sides). The apply heat to the back frame plate to loosen up the adhesive in the mid section of the screen. Then, slowly and I mean very, very slowly try to pry it open using a thin blade. Start from the top and work your way down. You should stop if you meet too much resistance and reapply heat. Like I said its a pain in the ass and not for the timid. I got to successfully remove an LCD from a frame for a Galaxy S (i500) not too long ago, its a similar in process as the GNex
I also tried to remove a L700 LCD (cracked glass) from a frame a while back and cracked it even more. I know what I did wrong and I think I wont make that mistake again. My mistake was that I did not know the exact location of the adhesive and applied too much heat in the front. Another mistake was that I thought I could remove the front glass from the digitizer. Now I know this is almost impossible and I don't know how people can buy front lenses without using some type of special tools (a true hot air bga station for instance) or a technique that I'm not aware of.
So, that's my long rant right there. I would really appreciate if any of you can confirm that any all 3 displays are the same (i9250, l700, i515). If it is then I would dare to try it out and take some pictures in the process if all goes well.
What about the oven?
I used to be into cars, and it was popular to smoke the headlamps on Nissans. They also have a lot of glue in them, and it was recommended to put em in an oven lol.
I'm sure it would get hot enough to loosen the screen, but 400 degrees may break something else in the process...
Sent from my Galaxy Nexus using xda premium
Did anyone ever find the answer to this question? I am wondering the same thing.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
You can't use the i9250 screen on the i515. The battery metal thingies and the vibration thing are in different places.
skier354 said:
Did anyone ever find the answer to this question? I am wondering the same thing.
Click to expand...
Click to collapse
I have asked a bunch of eBay sellers for the last few days and have gotten mixed responses... I don't think that most of them get that I am talking about separating the display from the front case/plate. One guy told me that the digitizer/LCD combo is interchangeable from the i515 and i9250, but it won't work on the L700. One guy told me that he thought that the entire assembly including the front plate were the same between the L700 and i515. Several have said that they are model specific, but I don't think that most of them realized that I am not expecting to use the front plate from an L700 if i9250 on the i515...
It doesn't seem like Samsung would have a different display for each model. I can see the plates and cases being different because some of the other parts are different, but it seems like the LCD panel and the glass should be the same for each model. To me all of the screen connectors look the same from the pics I've seen...
Edit- I just found this online store that indicates they are the same screens http://www.globaldirectparts.com/OEM-Galaxy-Nexus-L700-LCD-Digitizer-Assembly-p/smsng6115350-qs.htm
tristandespain said:
I remember reading on here somewhere that a person tried this and ran into all sorts of problems getting it to fit correctly. I tried searching but couldn't find the post.
Click to expand...
Click to collapse
Finally found the post that you are referring to (http://forum.xda-developers.com/showthread.php?t=1780491). Sounds like he ran into problems because he tried to use the i515's front housing on the i9250. I think if he had removed the screen from the frame and re-used the frame that was original to his phone he would have been fine. It looks like it takes some heat and care to do that, but it looks do able.
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
MrAreCool said:
I am ordering a L700 screen today and will report back on how it goes installing on my i515.
Click to expand...
Click to collapse
L700 screen (not including frame) worked on my i515. Details here.
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
perusmuro said:
Hi,
I have GT-I9250 phone and only that glass is broken. Touch and screen is fine. So if I bought this kit: http://www.ebay.com/itm/New-Outer-F...AU_MobilePhoneAccessories&hash=item5d371a5630
It's possible to change that glass or should i bought hole set? Digitizer+front cover + glass?
Click to expand...
Click to collapse
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
MrAreCool said:
I had a good LCD with broken glass that I was hoping to only replace the glass on and I ended up getting impatient and breaking the LCD. The glass is very difficult to get off. I tried heating it up and using fishing lines to separate the glass from the LCD, but I could not get very far. The glue seems to be spread over the entire surface and it does not take much prying to break the LCD.
Incidentally if the glass is shattered pretty badly you might have better luck than I did. I was able to get the broken "shards" off by heating up the screen and gently prying them off. Where I had trouble was the large section of unbroken glass. I tried to crack that glass to be able to continue to remove the shards, but I ended up breaking the LCD as well.
If you can't use the screen with the broken glass you might give it a go as you aren't really losing anything if you break it.
Good luck!
Click to expand...
Click to collapse
I have found few videos where that glass is possible to remove.
http://www.youtube.com/watch?v=JlfO6TUj1DQ
But I think that I would buy that whole set and change that. But what is the best place to buy that? So I can real deal.
Ok guys, just wanted to confirm that front glass for the L700 and GT-i9250 the same. And I assume that i515 as well.
I got for repair Nexus Sprint (L700) with cracked front glass but then was surprised that glass for L700 on ebay about $15 and the same glass for i9250 less then $10. Not big deal but anyway.. So I bought the glass for i9250 and it fits great as original.
Good luck!)
When the purchase of parts and mobile phones are not matched, the proposed replacement.

Dropped Galaxy S3 in Bathwater

Hey everyone, so my buddy recently dropped his Galaxy S3 in bath water. He ended up buying a new phone thinking the phone was dead but he turned it on a few days later and it worked. Everything works EXCEPT the touch buttons next to the home button. I bought the phone off of him for $150 thinking I can fix it but as I research video and threads online.. it seems much harder than I thought. I know that soaking the phone in 99% isopropyl alcohol can fix a lot of water damage problems but I'm not sure if I should soak the motherboard in it as it's working fine other than the touch sensor buttons. Should I dip only a part of the front frame (where the touch sensors are) in isopropyl alcohol stopping right below where the LCD screen starts?
I'd like to change the frame as well since there are some scratches here and there along with the home button. It works but the button is scratched up a bit.
Do you guys have any advice for me? The phone is currently disassembled btw if that helps.
Could always download lmt launcher and not worry about it?
Sent from my SAMSUNG-SGH-I747 using xda premium
Or modify your build.prop to add capacitive buttons
Sent from my SGH-I747 using Tapatalk 2
Just use a ROM that has navbar settings and dont worry about the buttons. I dropped my old optimus t in water and yea it comes back to life , but the uncertainty of how long it will work is terrible. A few weeks after it happend phone screen flickering and it just died.
Best thing to have done was pull the battery and let it dry for two or three days
Sent from my SGH-I747 using Tapatalk 2
Lots of ways to just bypass the buttons all together. Like thwy all said use a custom ROM and nav bar. Just let it dry and leave it be. Good luck.
Oh and give lmt launcher a shot too
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
I would definitely research cleaning it properly.
The water residue will eventually crust up and cause connection issues or shorts.
CZ Eddie said:
I would definitely research cleaning it properly.
The water residue will eventually crust up and cause connection issues or shorts.
Click to expand...
Click to collapse
What do you think is a good way to clean it? Dip the main board in isopropyl alcohol?
I am a tech junky, the first thing I would do is take it 100% apart and clean every inch on the inside. Eventually the stuff inside of that phone will turn cruddy from the bath water. $150 for a SGSIII is a hella good deal, rip it apart and give it a good cleaning.
Thanks yeah I thought it was a great deal, I could've asked him to drop it less but I felt bad since he was my friend. Phone is brand spanking new and only used for 2 months.
I'm thinking about buying a new whole front piece (LCD, digitizer, frame) though.. what do you guys think? I can get it online for $230ish and not sure how much I can get for my existing front piece.
artluo100 said:
Thanks yeah I thought it was a great deal, I could've asked him to drop it less but I felt bad since he was my friend. Phone is brand spanking new and only used for 2 months.
I'm thinking about buying a new whole front piece (LCD, digitizer, frame) though.. what do you guys think? I can get it online for $230ish and not sure how much I can get for my existing front piece.
Click to expand...
Click to collapse
I would try to fix it before going for a new front piece. Getting that new front piece + the 150$ you already paid = the price of a brand new S3 on ebay.
If it's himidity keeping them from working, leaving the phone in a seeled bag of rice for a couple days can fix it.
If you have the $$$ laying around to do it I would say go ahead. It may help the resell value down the road. I can't stand this phone naked, it feels like a big wet bar of soap in my hands. I would preserve the $$$ spent and put it in an Otterbox Commuter.
I was thinking about making back the money by selling the original piece. Not sure how much I can get for that though. The only thing holding me back is replacing the silver bezel around the LCD. You have to remove everything and swap it over including LCD, glass, buttons, etc. Sounds like a big risk for someone like who who has never done this type of work before.
artluo100 said:
I was thinking about making back the money by selling the original piece. Not sure how much I can get for that though. The only thing holding me back is replacing the silver bezel around the LCD. You have to remove everything and swap it over including LCD, glass, buttons, etc. Sounds like a big risk for someone like who who has never done this type of work before.
Click to expand...
Click to collapse
Well if getting someone to do it for you doesn't cost much, could be something to look into.
Yeah currently looking for someone to do that for me. Not sure where to look... all these cell phone repair places want to replace the whole piece PLUS they keep your LCD for "recycling" which means they'll take my LCD, repair it and sell it to the next sucker for $200 something.
I'm in NYC btw.. so by any chance any of you know someone in the area who has experience doing this, please let me know. Thanks!
artluo100 said:
Yeah currently looking for someone to do that for me. Not sure where to look... all these cell phone repair places want to replace the whole piece PLUS they keep your LCD for "recycling" which means I'll take your LCD, repair it and sell it to the next sucker for $200 something.
Click to expand...
Click to collapse
Haha. Well mobiletechvideos.com is well known around here, could be an option. I dunno how he proceeds though.
BWolf56 said:
I would try to fix it before going for a new front piece. Getting that new front piece + the 150$ you already paid = the price of a brand new S3 on ebay.
If it's himidity keeping them from working, leaving the phone in a seeled bag of rice for a couple days can fix it.
Click to expand...
Click to collapse
+1
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
Soaking it in 99% isopropyl alcohol right now. gave the mainboard a scrub down with a toothbrush about 1.5 hrs in. Also scrubbed the back of the touch screen, whichever resistors and chips I saw.
Fingers crossed.
Quick question.. how long should I let the parts dry after taking it out of the alcohol? It seems like alcohol evaporates pretty quick but the smell of it stays.

Categories

Resources