I was trying to install darky 10.2 resurrection from the 2.3.5 modaco rom, and it appeared to have hung at the "Set PIT file.." section. I gave it about 40mins, then unplugged it. Now it doesn't turn on, it doesn't give any response at all to anything I can do to it. Is it a goner?
I was previously using a san francisco and it seemed any stupid thing I could do to that was fixable somehow, perhaps I should have been more careful (although I was just following the instructions to get to the point where it stopped responding in odin)
hmm, some further searching reveals i have almost certainly bricked my phone permanently
and that ive put on a galaxy s rom onto my galaxy s2 what a dumbass
sorry to bother you
Lol. Anyways it's hard to brick a phone with Odin. Even so, you can resurrect it by using a USB jig.
i dont know, it seems ive made a fairly good job of it by trying to flash a rom for another phone onto it
Its very difficult to brick your phone WITHOUT ODIN. generally devices get bricked because of people playing with bootloaders and doing a mistake with some bootloader and you can't play with bootloaders from CWM you have to use Odin for that.
ahh yes, this is the difference between my experiences with the san fran and the galaxy, i was only using CWM on my san fran.
ronaldkh said:
Lol. Anyways it's hard to brick a phone with Odin. Even so, you can resurrect it by using a USB jig.
Click to expand...
Click to collapse
A good place to look for information about a JIG USB cable
http://forum.xda-developers.com/showthread.php?t=819551&highlight=jig
unbricakble mod for i9000 ...
so I was installing a new boatloader through odin and it failed to install; so I disconnected it. Ever since then, my computer simply will NOT recognize my phone. I have tried every possible method (using different slots and cable). Still, it will not recognize my phone at all.
Has anyone here ever encountered a similar situation and have found a solution?
I would highly appreciate any help. Thanks
What does the phone boot to?
Have you tried a USB jig?
The bootloader takes seconds to flash. Did you really press start and immediatly pull the USB cord? or did it not complete then you pulled the cord? If the latter, what did ODIN say in the logs?
I can get into odin or recovery mode with no problem, I loaded a custom testing version of an ICS Rom that failed to completely install.
I am waiting for my usb jig to come in the mail.
It installed like 80% and then said failed, then I removed it because it said it failed.
I know all my drivers are good because my sister has the same phone and it is unrooted and odin recognizes it fine.
sabatheman said:
I can get into odin or recovery mode with no problem, I loaded a custom testing version of an ICS Rom that failed to completely install.
I am waiting for my usb jig to come in the mail.
It installed like 80% and then said failed, then I removed it because it said it failed.
I know all my drivers are good because my sister has the same phone and it is unrooted and odin recognizes it fine.
Click to expand...
Click to collapse
If you can get into Odin mode then Odin should be able to recognize your phone. Are you sure that Odin on your PC is not recognizing your phone?
Also, try flashing the el26 stock rooted update through cwm. Calk has the appropriate zip over in the dev section.
Sent from my SPH-D710 using Tapatalk
sabatheman said:
so I was installing a new boatloader through odin and it failed to install; so I disconnected it. Ever since then, my computer simply will NOT recognize my phone. I have tried every possible method (using different slots and cable). Still, it will not recognize my phone at all.
Has anyone here ever encountered a similar situation and have found a solution?
I would highly appreciate any help. Thanks
Click to expand...
Click to collapse
Where did you find a boatloader for our phones?!?!?!? That would be a truly Epic accessory for all boatloading enthusiasts! Think of the activities!
Haha, in all seriousness though, I hope you can get it figured out man, bricked phones are no fun!
yes, im 100% sure, Ive read of a few cases of people having similar problem. Problem that come from disconnecting a phone while loading a new boatloader. Once that happens, odin will not recognize a phone even if it is in Odin mode. Ive spent atleast 15 hours in total trying to get it to work
bump bump bump
sabatheman said:
I loaded a custom testing version of an ICS Rom that failed to completely install.
Click to expand...
Click to collapse
Is this one made for E4GT or one for the european GS2?
If you can get into recovery just take the sd card out and put it in a sd reader and put a rom on there and flash it. I would use the stock rom. Something simillar happened to me and this is how I fixed it. I didnt have a card reader so I just used my digital camera, Thank god for that!!! Hope it all works out.
---------- Post added at 12:12 AM ---------- Previous post was at 12:11 AM ----------
sfhub said:
Is this one made for E4GT or one for the european GS2?
Click to expand...
Click to collapse
Good question! I almost bricked my phone by putting a rom on there that was for the international version! You need to triple check to make sure what you are putting on is actually for your phone!
sabatheman said:
I can get into odin or recovery mode with no problem, I loaded a custom testing version of an ICS Rom that failed to completely install.
I am waiting for my usb jig to come in the mail.
It installed like 80% and then said failed, then I removed it because it said it failed.
I know all my drivers are good because my sister has the same phone and it is unrooted and odin recognizes it fine.
Click to expand...
Click to collapse
Omg again people don't read. We don't have ics from for our phone! Gosh try to download the international gs2 drivers of get your phone jtaged. If not you got a paperweight
Sent from my SPH-D710 using Tapatalk
I installed the one for the european s2 version,
rbtrucking, Ive tried doing that, but it says unable to mount the sd card when i go into recovery mode and applying update from external storage? any idea why?
sabatheman said:
I installed the one for the european s2 version,
Click to expand...
Click to collapse
Your problem isn't that you disconnected the phone while flashing a new bootloader.
Your problem is you flashed the european GS2 version of the bootloader. After doing that the USB port is pretty much disabled and nobody has found how to enable it.
interesting... any theoretical methods to get it to work? do you think there will be a solution to fix it?
sfhub said:
Your problem isn't that you disconnected the phone while flashing a new bootloader.
Your problem is you flashed the european GS2 version of the bootloader. After doing that the USB port is pretty much disabled and nobody has found how to enable it.
Click to expand...
Click to collapse
Nothing should be flashed to the Epic Touch unless its in the development section for the Epic Touch. Even then you should read up and know the pros and cons of flashing it. I don't recall anyone getting their phone back after doing this.
Sent from my SPH-D710 using xda premium
Well Mobile ODIN won't flash the bootloader AFAIK, so if you have no way to flash the bootloader, the only other possibility will probably be JTAG, which is basically opening up the phone connecting to some pins/leads on the board and using some software to flash. I haven't seem anyone posting about this but probably there are techs who have the proper setup to do it.
damn, do you think if I go to a sprint corporate store and just say I was trying to update the phone via samsung kies OTA or something, will they be able to fix it? I am waiting for my jig to come in the mail to clear the download count, any opinions what I should tell sprint to avoid getting my warrenty voided?
sabatheman said:
I installed the one for the european s2 version,
rbtrucking, Ive tried doing that, but it says unable to mount the sd card when i go into recovery mode and applying update from external storage? any idea why?
Click to expand...
Click to collapse
Ya because like everyone else said flashing that file that wasnt for your phone messed up the sd reader. Same thing happened to me once but I was still able to acess the internal storage that the phone has built in but i didnt have any roms on there. I was however able to flash through odin and dowload mode. Thank god that worked for me! If that isnt working for you I gotta be honest I really dont see a way to get the phone back up and running but I am by no means a pro. I would keep at it. When I almost bricked my phone I was going to give up too but I stuck with it and the fine people on this site pulled me through! You are at the right place trust me very smart people here!
thanks, this phone has been bricked for a week, Im still waiting on my usb jig to come in the mail so i can hopefully clear the binary download count because I want to take it to sprint? since my usb and sd reader isnt working, will the usb clear the odin thing? if it doesnt, im completely screwed. im willing to short out my phone worst case scenario... I need it a replacement (i dont have insurance but i have warrenty)... any ideas? should i short it out or take it to sprint... what excuse should I make up if I decide to take it?
Will the usb jig clear the download count even though my usb and sd reader doesnt work. (the phone still charges through usb)
sabatheman said:
thanks, this phone has been bricked for a week, Im still waiting on my usb jig to come in the mail so i can hopefully clear the binary download count because I want to take it to sprint? since my usb and sd reader isnt working, will the usb clear the odin thing? if it doesnt, im completely screwed. im willing to short out my phone worst case scenario... I need it a replacement (i dont have insurance but i have warrenty)... any ideas? should i short it out or take it to sprint... what excuse should I make up if I decide to take it?
Will the usb jig clear the download count even though my usb and sd reader doesnt work. (the phone still charges through usb)
Click to expand...
Click to collapse
Ya if you have warranty i would actually just short it out! I had a friend that had an iPhone and he hooked it up to a computer with a messed up usb. It shorted it out, he took it back with his warranty info and walked out with a brand new iPhone no questions asked. If you dont and they see that it was routed you are going to be **** out of luck I can tell ya that. They definitely will inspect it to make sure there was no foul play with it trust me, best bet if you cant get it running is to short it out, and use the warranty. When you take it in just say it went off and you couldn't get it to go back on.
Honestly breaking the phone is your best option since the insurance will cover that. If you short it out or make the batter overload while it's in the phone then it's covered by the warranty. Also, clearing the download counter is pointless - if Sprint does manage to fix your phone it'll be pretty obvious you did something that made it FUBAR - mostly the international GS2 bootloader. Also, isn't the international GS2 GSM? Which means you can't reset it using a JIG, GSM versions don't support it.
Either way when you get a new one - make sure you read EVERYTHINGlet me say this again since people seem to take this stuff lightly: READ EVERYTHING BEFORE FLASHING if we had ICS for this phone don't you think the Dev section would be blowing up with ICS ROMs? Common sense seems to be the one thing that isn't common anymore....
Hope you figure something out though but I wouldn't hold my breath.
I've done some searching ever since my S2 hardbricked and I found some similar but also very different stories with man different answers.
In my case, my gs2 is out of warranty. I was running CM9 but I had poor audio transmittance so I decided to flash a stock rom. That worked and was easy enough. I assumed I wasn't rooted since I just flashed stock. So I go to root my phone, and then it dies. Does not respond to the computer. It doesn't turn on nor can it go into recovery/download mode. Also doesn't chrge. I'm pretty sure I'm hardbricked. I made sure my battery was full too (I have an external charger). I tried a homemade usb jig. I think it didn't work due to my poor soldering skills. Given this situation, should I buy a usb jig and try to get it started or is it at the point where I should JTAG it.
Thanks all.
Feel for u bro mine did the same except I could access recovery but I couldn't boot up. I just Odin back to stock but that didn't work at first I had to do it a few times. You shouldnt flash to stock always odin it back
Sent from my SGH-T989 using xda premium
bought this galaxy s2 from a friend perfect condition nothing was wrong with it. rooted it flashed a rom(made backups)didnt really like the rom very much. tryed to flash another one and it said it failed to install so i restored to orignal stock and i guess when it was done turned off and now it wont turn on. i have tryed going into recovery. nothing. when i plug into computer (at school computer it looks like it found something but my computer wont install it so i will say somthing when i get home. please help this phone is wonderfull i dont know what i did im very pissed i cant send it to samsung because its not my phone phone.
when i looked at the rom zip on the sd card i had it said i777 im sure thats meaning the sgh i777 soo.....
You flashed a ROM for a completely different phone. This is a T989 not an I777... Your totally bricked and you'll need a jig to force it into download mode to Odin back to the correct firmware . if you do some searching you'll figure it out I'm sure..
Sent from my SAMSUNG-SGH-T989 using xda app-developers app
i now know i flashed from a different phone... but it was in this forun that i got the rom from so.. also do you know if it is easyer to mak a usb jig or buy one?
Trozzul said:
i now know i flashed from a different phone... but it was in this forun that i got the rom from so.. also do you know if it is easyer to mak a usb jig or buy one?
Click to expand...
Click to collapse
If it's hard bricked this might be your only option. They charge $50 for fixing a bricked t989.
http://mobiletechvideos.mybigcommerce.com/
Sent from my SAMSUNG-SGH-T989 using Tapatalk 2
you can make a jig but if your not good with building stuff like that then just buy a jig
btw please im not trying to flame you but please read what phone the rom is for next time
and if your not sure ask questions!
thats what we are here for!!!!
i did read what the rom was it was from this forum that i got it from. also when i build the usb jig what do i do from there? i dont know how to flash a rom from odin
i built a usb jig and it still wont turn on. i just got this why does this always happens to my phones...
Just buy one. Correct me if I'm wrong but they usually cost around $1-2
Got my MTV jig today...I'm charging the battery to my bricked SG3 at the moment in an external charger to make sure it has enough juice to get the job done. The MTV site said this jig will work on ALL SG's 2 and 3 so I guess this will be the ultimate test since I'm reading different things everywhere. Now for my question(s), am I supposed to be able to just plug the jig in, do the key combo for download mode and then the magic happens immediately? I also need to get a stock rom, not the one with root injected because I was reading the instructions on how to install the root injected rom and it says Odin needs to do the install for it. I dont see how that'll happen in my phone's current state (hard bricked). Say the jig works and download mode pops up, will it continue popping up on its own like if I were to plug into the pc? Sorry, just slightly confused
If you're hard bricked a jig won't work for that. You would need to get a JTAG service to fix a hard brick. But. If its not hard bricked then all you need to do is plug the jig in and your device will automatically go into download mode. Then from there you can use odin to flash a stock ROM and you'll be up and running again.
task650 said:
If you're hard bricked a jig won't work for that. You would need to get a JTAG service to fix a hard brick. But. If its not hard bricked then all you need to do is plug the jig in and your device will automatically go into download mode. Then from there you can use odin to flash a stock ROM and you'll be up and running again.
Click to expand...
Click to collapse
...please tell me you're joking....
I thought the jig was to bypass whatever is causing the phone not to boot allowing you to at least get into download mode or recovery....I have a feeling I'm gonna puke now. It's definitely hard bricked. I accidentally loaded an i9300 rom on my i747...completely dead to the world.
Momomuffins said:
...please tell me you're joking....
I thought the jig was to bypass whatever is causing the phone not to boot allowing you to at least get into download mode or recovery....I have a feeling I'm gonna puke now. It's definitely hard bricked. I accidentally loaded an i9300 rom on my i747...completely dead to the world.
Click to expand...
Click to collapse
A jig is only useful for a soft brick as task has said, hard brick needs a jtag repair.
Sent from my SAMSUNG-SGH-I747 using xda premium
To use the jig, just plug it in. No key combo needed
Well my phone is definitely hard bricked...AT&T won't exchange my phone because I transferred tmy service to another carrier a month ago...the other carrier is run by a bunch of asshats giving me the run around...SO...I'm gonna try a Samsung warranty exchange. I can't afford a JTAG right now since I'm not working...FML.../end