Related
EDIT: OP EDITED WITH CHANGED PTA SETTINGS UNDER APN TYPE!
After reviewing the GS2 thread on the same topic (http://forum.xda-developers.com/showthread.php?t=1109983), I thought it might be worthwhile to discuss this issue on the Nexus. I was not able to get the Nexus connected using the information in that thread. However, I was able to get it connected to pta using a slightly modified version of the Skyrocket settings, which I'll post below.
One quick question before I do that, though -- I am only able to get 3 mb/s or so on my Nexus. I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Anyway, here are working settings to get to PTA (the one the Skyrocket uses):
1) Go to settings, more (under networks), Access Point Names
2) Click on the 3 dots to create a new APN, name it AT&T PTA, and enter the following:
Name: ATT pta
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMS Proxy: not set
MMS port: not set
MCC: 310
MNC: 410
Authentication type: not set
APN type: default,internet,supl [NOTE NO SPACES IN THIS]
APN Protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecified
3) Then separately create another new APN and enter the following:
Name: AT&T US MMS
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
Username: not set
Password: not set
Server: not set
MMSC: http://www.mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: not set
APN type: mms
APN protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecify
4) Make sure the little circle next to AT&T pta is green.
5) Wait for the device to connect and then restart it.
I had a hard time finding these settings, so I thought it might be helpful to someone else here.
Parent/Teacher Association
oscillik said:
Parent/Teacher Association
Click to expand...
Click to collapse
No. Bad joke.
Sent from my GT-I9100 using xda premium
Not to be too paranoid, but will messing with these settings make it appear you are, say, tethering? I don't want to lose my unlimited data on ATT and fear that changing anything to access faster speeds may flag me for using a computer?
Similar to when the Dolphin desktop mode was flagging people on ATT, prompting the carrier to accuse users of tethering...
I wasn't aware Galaxy Nexus had the proper radio for this...
nirvanayoda said:
After reviewing the GS2 thread on the same topic (http://forum.xda-developers.com/showthread.php?t=1109983), I thought it might be worthwhile to discuss this issue on the Nexus. I was not able to get the Nexus connected using the information in that thread. However, I was able to get it connected to pta using a slightly modified version of the Skyrocket settings, which I'll post below.
One quick question before I do that, though -- I am only able to get 3 mb/s or so on my Nexus in Houston (an AT&T favorite city). I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Anyway, here are working settings to get to PTA (the one the Skyrocket uses):
1) Go to settings, more (under networks), Access Point Names
2) Click on the 3 dots to create a new APN, name it AT&T PTA, and enter the following:
Name: ATT pta
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMS Proxy: not set
MMS port: not set
MCC: 310
MNC: 410
Authentication type: not set
APN type: default,supl [NOTE NO SPACES IN THIS]
APN Protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecified
3) Then separately create another new APN and enter the following:
Name: AT&T US MMS
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
Username: not set
Password: not set
Server: not set
MMSC: http://www.mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: not set
APN type: mms
APN protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecify
4) Make sure the little circle next to AT&T pta is green.
5) Wait for the device to connect and then restart it.
I had a hard time finding these settings, so I thought it might be helpful to someone else here.
Click to expand...
Click to collapse
Are you using AT&T's LTE provisioned SIM? that's probably why you're seeing the issue. Also that SoC code is LTE provisioned code which doesn't help.
milan03 said:
Are you using AT&T's LTE provisioned SIM? that's probably why you're seeing the issue. Also that SoC code is LTE provisioned code which doesn't help.
Click to expand...
Click to collapse
I am using an AT&T LTE provisioned SIM and my SOC code is LTE, so that could be part of the problem. But also keep in mind, I had that done just in case AT&T ever started to refuse to upgrade unlimited data users to LTE unlimited data. Right now, they're eager to get the LTE towers full, so they won't stop such upgrades -- that may change in the future.
Anyway, I played with my settings for a long time tonight and realized that APN type needs to read "default,internet,supl", not just "default,supl". I have no idea what that means or why it matters, but when I changed that, my speeds definitely increased. To give a comparison, at 1 AM, I got the following speeds:
default wap.cingular APN -- 4-5 Mb for most test servers
phone APN (as described in the thread linked in the OP) -- Average of 5 Mb for most test servers and high of 6 Mb
pta APN (as described above) -- average of 7 Mb for most test servers and high of 8 Mb
The difference isn't exactly extreme, and it's far lower than I'd hoped for, but I think pta is demonstrably faster, at least in my area. I'm eager to see how it does during the work day tomorrow.
I just tried this in Saint Lous, MO and I get no data service with pta
sluflyer06 said:
I just tried this in Saint Lous, MO and I get no data service with pta
Click to expand...
Click to collapse
Are you sure this line was exact (with no spaces)? Without "default" there it won't get me data services either, but with it I do:
APN type: default,internet,supl
No data for me either, reverted back to the dault cingular apn...though the HSPA+ phone APN that is floating around these board damn near doubled my speeds.
mrflips said:
No data for me either, reverted back to the dault cingular apn...though the HSPA+ phone APN that is floating around these board damn near doubled my speeds.
Click to expand...
Click to collapse
Just curious... If the HSPA+ APN doubled your speed, then why go back to the default cingular settings?
Im confused, why would the PTA apn do anything in the first place? i thought the i9250 version of the GNex isnt equiped with an LTE radio. Im in Los Angeles, CA where theres no LTE, i cant even get data with the PTA APN on my skyrocket. Unless I am mistaken and theres an LTE radio? id be so happy. Can anyone confirm? GSMARENA.COM list the specs for the i9250 with LTE 700mhz but other sites dont.
oatterzonxda said:
Im confused, why would the PTA apn do anything in the first place? i thought the i9250 version of the GNex isnt equiped with an LTE radio. Im in Los Angeles, CA where theres no LTE, i cant even get data with the PTA APN on my skyrocket. Unless I am mistaken and theres an LTE radio? id be so happy. Can anyone confirm? GSMARENA.COM list the specs for the i9250 with LTE 700mhz but other sites dont.
Click to expand...
Click to collapse
The 9250 doesn't have LTE. It's HSPA+.
oatterzonxda said:
Im confused, why would the PTA apn do anything in the first place? i thought the i9250 version of the GNex isnt equiped with an LTE radio. Im in Los Angeles, CA where theres no LTE, i cant even get data with the PTA APN on my skyrocket. Unless I am mistaken and theres an LTE radio? id be so happy. Can anyone confirm? GSMARENA.COM list the specs for the i9250 with LTE 700mhz but other sites dont.
Click to expand...
Click to collapse
It does not have LTE. It has HSPA+ (which AT&T and T-Mobile advertise as 4G). The poster here was saying he previously used a Galaxy S II Skyrocket (which is an AT&T LTE device) and because of that, his data plan is LTE and his SIM is an LTE SIM.
Anyway, I used the APN settings listed around this board and it doesn't seem to make a difference. When I used the settings posted, speedtest wouldn't work properly. It said I was getting 7kbps when it clearly wasn't that slow in real world usage. Going back to default fixed that issue, but I'm only getting about 3.5mbps down. I'd be happy to be getting 5. I already called AT&T and confirmed I've been changed over to an HSPA+ data SOC. Also, I got a new SIM card yesterday since my last one was from when I got my iPhone 3GS a couple years ago.
nirvanayoda said:
I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Click to expand...
Click to collapse
If you have an LTE SOC, you can use the LTE APN but the device doesn't support LTE. You might as well get the HSPA+ SOC and use the HSPA+ APN.
milan03 said:
Are you using AT&T's LTE provisioned SIM? that's probably why you're seeing the issue. Also that SoC code is LTE provisioned code which doesn't help.
Click to expand...
Click to collapse
Using the latest AT&T LTE compatible SIM will not cause a problem. It is backward compatible with all AT&T plans. As for an incorrect SOC, well that's a different story and may have unpredictable results although a number of people have different SOCs/APNs working to their satisfaction.
Since a lot of people here think the LTE SIM is not compatible with HSPA/HSPA+, I am posting part of an official communique for "company owned" device users that went out just before the new LTE SIM was rolled out:
ATT said:
Next Generation SIM card for 4G devices now available
The new SIM card for 4G LTE devices is available for ordering in the COU system. While this SIM is required for 4G LTE devices, it is also compatible with 3G devices and COU will be shipping the 4G LTE SIM with every device make and model going forward (with exception to iPhone 4/iPad 3G +WiFi).
The new SIM (SKU 73057) includes enhancements that will enable functionality for LTE capable devices when supported by the network.
Click to expand...
Click to collapse
nirvanayoda said:
EDIT: OP EDITED WITH CHANGED PTA SETTINGS UNDER APN TYPE!
After reviewing the GS2 thread on the same topic (http://forum.xda-developers.com/showthread.php?t=1109983), I thought it might be worthwhile to discuss this issue on the Nexus. I was not able to get the Nexus connected using the information in that thread. However, I was able to get it connected to pta using a slightly modified version of the Skyrocket settings, which I'll post below.
One quick question before I do that, though -- I am only able to get 3 mb/s or so on my Nexus in Houston (an AT&T favorite city). I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Anyway, here are working settings to get to PTA (the one the Skyrocket uses):
1) Go to settings, more (under networks), Access Point Names
2) Click on the 3 dots to create a new APN, name it AT&T PTA, and enter the following:
Name: ATT pta
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMS Proxy: not set
MMS port: not set
MCC: 310
MNC: 410
Authentication type: not set
APN type: default,internet,supl [NOTE NO SPACES IN THIS]
APN Protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecified
3) Then separately create another new APN and enter the following:
Name: AT&T US MMS
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
Username: not set
Password: not set
Server: not set
MMSC: http://www.mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: not set
APN type: mms
APN protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecify
4) Make sure the little circle next to AT&T pta is green.
5) Wait for the device to connect and then restart it.
I had a hard time finding these settings, so I thought it might be helpful to someone else here.
Click to expand...
Click to collapse
my account is LTE provisioned too(came from skyrocket) and these are almost the exact settings I ended up with as well after messing around with them and comparing with other skyrockets and SG2.
i have not been using the "internet" in the "default,internet,supl" setting, I just had "default,supl".
i have added the internet to see if I see any changes. these are the fastest Ive been able to get my GN to perform at. still not as fast as my skyrocket was using h+, and the MMS take a while to send/recieve sometimes.
nirvanayoda said:
EDIT: OP EDITED WITH CHANGED PTA SETTINGS UNDER APN TYPE!
After reviewing the GS2 thread on the same topic (http://forum.xda-developers.com/showthread.php?t=1109983), I thought it might be worthwhile to discuss this issue on the Nexus. I was not able to get the Nexus connected using the information in that thread. However, I was able to get it connected to pta using a slightly modified version of the Skyrocket settings, which I'll post below.
One quick question before I do that, though -- I am only able to get 3 mb/s or so on my Nexus in Houston (an AT&T favorite city). I am on the unlimited data SOC code for LTE: LDPPVM5 -- think that code is causing any problems?
Anyway, here are working settings to get to PTA (the one the Skyrocket uses):
1) Go to settings, more (under networks), Access Point Names
2) Click on the 3 dots to create a new APN, name it AT&T PTA, and enter the following:
Name: ATT pta
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMS Proxy: not set
MMS port: not set
MCC: 310
MNC: 410
Authentication type: not set
APN type: default,internet,supl [NOTE NO SPACES IN THIS]
APN Protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecified
3) Then separately create another new APN and enter the following:
Name: AT&T US MMS
APN: wap.cingular
Proxy: wireless.cingular.com
Port: 80
Username: not set
Password: not set
Server: not set
MMSC: http://www.mmsc.cingular.com
MMS Proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: not set
APN type: mms
APN protocol: IPv4
APN enable/disable: APN enabled
Bearer: Unspecify
4) Make sure the little circle next to AT&T pta is green.
5) Wait for the device to connect and then restart it.
I had a hard time finding these settings, so I thought it might be helpful to someone else here.
Click to expand...
Click to collapse
Confirm that after obtaining new SIM to replace my 3 year old one and provisioning with a Skyrocket IEMI with LTE unlimited data plan I now am regularly 5Mbps down and hit 7-8Mbps at times. Latency is around 130ms.
MMS not playing nice. I haven't tested send and receive enough to say it works for me or not. I'll check in the morning when texting.
updated: no mms
lpasq said:
Confirm that after obtaining new SIM to replace my 3 year old one and provisioning with a Skyrocket IEMI with LTE unlimited data plan I now am regularly 5Mbps down and hit 7-8Mbps at times. Latency is around 130ms.
MMS not playing nice. I haven't tested send and receive enough to say it works for me or not. I'll check in the morning when texting.
updated: no mms
Click to expand...
Click to collapse
Have you tried using apn: phone? with the mms settings? Just wondering.
ebaul said:
Have you tried using apn: phone? with the mms settings? Just wondering.
Click to expand...
Click to collapse
Yes. Thank you. I did do so. My calls to ATT level 2 tech support and then a Supervisor now claim my issue is related to provisioning. The sim is correctly provisioned as pta with APN type settings as default,internet,mms,supl. I am told my account settings as part of my customer profile does not correctly reflect my IEMI and therefore my MMS feature is wonked. Sounds like I am in the customer service black hole waiting for my service ticket to make it through helpless-desk hell. There is something to what I am being spun because my online account is all screwed up. I love smartphone gadgets and hate wireless carriers!
lpasq said:
Yes. Thank you. I did do so. My calls to ATT level 2 tech support and then a Supervisor now claim my issue is related to provisioning. The sim is correctly provisioned as pta with APN type settings as default,internet,mms,supl. I am told my account settings as part of my customer profile does not correctly reflect my IEMI and therefore my MMS feature is wonked. Sounds like I am in the customer service black hole waiting for my service ticket to make it through helpless-desk hell. There is something to what I am being spun because my online account is all screwed up. I love smartphone gadgets and hate wireless carriers!
Click to expand...
Click to collapse
Ok, for the sake of argument, try this please and report back. I have a Vivid that I bought unsubs, therefore I didn't get it from at&t, but from Tigerdirect.com and I had to set my apn because I live in York, PA and there is no LTE here. I am able to send and receive mms and access internet at 6+ mbps and I didn't call at&t to report my new phone. Here are my APN settings:
I setup 2 apns, below are both:
APN1:
Name: AT&T HSPA+
(everything else leave blank until the end, which you will
APN type: default,admin,fota,hipri
APN2:
Name: AT&T MMS
APN: wap.cingular
MMSC: http://mmsc.cingular.com
MMS proxy: wireless.cingular.com
MMS port: 80
APN type: mms
Those are my settings and again I can send and receive MMS and access internet. Ensure the radio is clicked on AT&T HSPA+
Hope this helps.
I finally got around to flashing CM10, but can't seem to get the 4G working. I get H+/3g data, but no 4g. I flashed the CM10 nightly from 10/2.
My IMEI is in tact, I know the modem I am using works correctly in this area.
Here if my APN information:
Code:
Name: ATT LTE
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMSC: hXXp://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Athentication Type: None
APN type: default,supl,mms
APN protocol: IPv4
APN enable/disable: enabled
Bearer: unspecified
Has anyone else run into a similar problem?
I realized I had a similar problem on CM9 and found two things:
1) APN type: default,supl,mms,hipri
I added hipri to APN type (not 100% sure it was needed)
2) In mobile network settings I had not selected LTE in the Network Mode option list. (THIS was my problem) It's one of those, duh of course I have that set moments..when I really didn't. So double check that setting.
thefightforgood said:
I finally got around to flashing CM10, but can't seem to get the 4G working. I get H+/3g data, but no 4g. I flashed the CM10 nightly from 10/2.
My IMEI is in tact, I know the modem I am using works correctly in this area.
Here if my APN information:
Code:
Name: ATT LTE
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMSC: hXXp://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Athentication Type: None
APN type: default,supl,mms
APN protocol: IPv4
APN enable/disable: enabled
Bearer: unspecified
Has anyone else run into a similar problem?
Click to expand...
Click to collapse
First of all...are you in an LTE area? When you were on an ATT rom did it say 4G LTE or just 4G?
rquinn19 said:
First of all...are you in an LTE area? When you were on an ATT rom did it say 4G LTE or just 4G?
Click to expand...
Click to collapse
I believe THIS was my problem. On ATT roms it would say 4G (I'm not in an LTE area) - apparently on CM roms this translates to H+. Looks like I never really had a problem at all.
Thanks! Consider this solved.
You shouldnt refere to to LTE/HSPA+ as 4G. Just name it by what it is. Much eqsier to identify what the problem area is.
Sent from my SAMSUNG-SGH-I747 using xda premium
When it comes to CM ROMs HSPA+ will be identified by and "H" and LTE by a 4G
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
I finally got around to flashing CM10, but can't seem to get the 4G working. I get H+/3g data, but no 4g. I flashed the CM10 nightly from 10/2.
My IMEI is in tact, I know the modem I am using works correctly in this area.
Here if my APN information:
Name: ATT LTE
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMSC: hXXp://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Athentication Type: None
APN type: default,supl,mms
APN protocol: IPv4
APN enable/disable: enabled
Bearer: unspecified
Click to expand...
Click to collapse
Has anyone else run into a similar problem?
Click to expand...
Click to collapse
Change the following in your APN settings this resolved many 4g signal issues. I take no credit for this whatsoever. This was from another poster and I had these settings saved I just can't seem to find his post otherwise I would have linked it directly. If you happen to come across it be sure to hit the thanks button. If it really helped you donations wouldn't hurt for the original poster. Thank you. -
APN type:default,admin,fota,mms,supl,hipri,internet
APN protocol :IPv4/IPv6 (this setting experimental and is optional)
(make sure NO spaces after commas)
BEARER: LTE
Sent from my SGH-I747 using xda app-developers app
Have you actually ran speed test to confirm network speed?
Im actually having the same problem... Im using the infuse 4g with a cyanogen 4.2.1. Iunlocked my phone and am using a t-mobile sim (therefore, towers) and even though my phone is staying in one place the signal is going from E (econ, 2g) to 3g and H ( basically 3.5g) (back and forth) and never really stops...also the signal will be at full bars, then drop to no service and do it all over again.
Im obviously having service problems when i shouldnt and im not sure if im getting 4g at all even though i called and they said my plan was full-time 4g depending on coverage... OR..." H " is mobil's name for 4g (actually HSPDA + HSUPA which is technically considered 3.5).. Any help on the matter would be greatly appreciated.
Are you having issues with LTE on an AOSP ROM? Look here for information, and post any questions you may have about the subject.
First, we need to debunk the carrier's explanation of 4g. The carriers will explain to you that if it says 4g on the stock ROM you are using LTE. That is NOT true, 4g on the stock ROM is actually H, or H+, which is technically 3.5g, and not LTE. The stock ROM displays LTE as 4g LTE
So the first thing you need to do is make SURE you are in a location that has LTE coverage. Go to your carrier's website and verify with their coverage map
Coverage Maps:
AT&T
Rogers
Bell
Telus
AOSP based ROMs display your true network connectivity as follows:
G = GPRS
E = EDGE
3g = 3g
H = HSDPA / HSPA
H+ = HSDPA+ / HSPA+
4g = LTE
For Canadian users, you MUST verify LTE / GSM / WCDMA is selected.
The Dialer Code is *#*#DATA*#*# (or *#*#4636#*#*). You will enter the Data Programming menu, to set it.
Here is an app that will access the menu for you:
LTEOnOFF
Reported ROMs the settings stick on reboot:
CM10
SlimBean
AOKP
Now you have to verify you are using the correct LTE APN settings, and if not, add it.
You can access your APNs by "System Settings => More => Mobile networks => Access Point Names"
Here are the LTE settings for ALL US and Canadian carriers:
AT&T
Name: ATT PTA
APN: pta
MMSC: http://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS port: 80
MCC: 310
MNC: 410
Auth: none
APN type: default,mms,supl,hipri
Rogers
APN - ltemobile.apn
Proxy - <not set>
Port - <not set>
Username- <Not set>
Passwors - <not set>
Server < not set>
MMSC - http://mms.gprs.rogers.com
MMS - proxy 10.128.1.69
MMS - Port 80
MMS protocol - Wap 2.0 or Blank
MCC - 302
MNC - 720
Aythentication type - < not set>
APN type - either "*" or "internet + mms" Should work
Bell
APN: pda.bell.ca
Proxy: web.wireless.bell.ca
Port:80
Username: Not set
Password: Not set
Server: Not set
MMSC: http://mms.bell.ca/mms/wapenc
MMS Proxy: web.wireless.bell.ca
MMS Port: 80
MCC:302
MNC: 610
Authentication Type: Not set
APN Type: Not set
Telus
NAME: TELUS SP
APN: sp.telus.com
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMSC: http://aliasredirect.net/proxy/mmsc
MMS Proxy: 74.49.0.18
MMS Port: 80
MMS Protocol: WAP 2.0
MCC: 302
MNC: 220
Authentication type: not set
APN Type: default,mms,hipri
Bearer: unspecified
Alaska Communications (ACS)
2 APNs
Data APN:
Name: ACS Data
APN: web.acs
MCC 311 (Default)
MNC 370 (Default)
APN type: “default,supl” or “*”
MMS APN:
Name: ACS MMS
APN: mms.acs
MMSC: http://mmsc.gci.csky.us:6672
MMS proxy: 209.4.229.92
MMS port: 9201
MCC 311 (Default)
MNC 370 (Default)
APN type: mms
Or the easiest way to do it would be just to edit the two current (GCI) APNs and change in the APN where ‘gci’ is listed to ‘acs’.
-Frozen
Fido
apn: ltemobile.apn
mmsc: http://mms.fido.ca
mms proxy: 204.151.11.13
mms port: 80
mcc: 370
apn type: internet +mms
reserved for god
My lte wasn't working when I flashed to cm10 yesterday. I did the steps you stated, deleted all other apn other than the rogerslte one and restarted my phone. It has been working since then.
Sent from my SGH-I747 using xda app-developers app
Deoxlar said:
My lte wasn't working when I flashed to cm10 yesterday. I did the steps you stated, deleted all other apn other than the rogerslte one and restarted my phone. It has been working since then.
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
Carrier? could you post your settings for help with the guide? If they look exactly the same, just say theyre the same...
I'm with Rogers, everything is the same except for the mms protocol. I left mine blank instead of Wap 2.0
I believe cm10 sometimes resets some settings back to default if you don't reboot after changing a setting. But I'm not 100percent sure.
Sent from my SGH-I747 using xda app-developers app
Deoxlar said:
I'm with Rogers, everything is the same except for the mms protocol. I left mine blank instead of Wap 2.0
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
fixed, thx
Will place in AT&T Index shortly.
Excellent job... noob
I'd like to mention that the LTE / GSM / WCDMA selection does not revert after every reboot on any Canadian S3 that I know of with CM10, and has never done so to my knowledge. If this is happening in other AOSP ROMs, it is a ROM specific problem.
The setting does revert to the default after a data wipe though.
Could users of other AOSP ROMs comment on does it stick on reboot?
Quasimodem said:
Could users of other AOSP ROMs comment on does it stick on reboot?
Click to expand...
Click to collapse
I've been using Slimbean 2.6 and 2.7 for several weeks now and can confirm LTE is sticking. However I certainly don't think I'm getting the as high a LTE connectivity rate as with the stock rom.
finneginsfast said:
I've been using Slimbean 2.6 and 2.7 for several weeks now and can confirm LTE is sticking. However I certainly don't think I'm getting the as high a LTE connectivity rate as with the stock rom.
Click to expand...
Click to collapse
There's so many factors that can contribute to that... too ambiguous to T/S.... It's a trial and error thing... Location, network traffic, and the modem you're currently running...
Quasimodem said:
There's so many factors that can contribute to that... too ambiguous to T/S.... It's a trial and error thing... Location, network traffic, and the modem you're currently running...
Click to expand...
Click to collapse
This is definitely true. Only way I can tell though with a degree of certainty is with a network monitoring app and the fact that I've got pretty standard area of operation.
I've been running kyanrom though for the past couple days and I'm back to getting a much higher degree of LTE connections. I guess while I'm at it, I can also confirm that LTE is sticking with kyanrom also.
APNs for Alaska Communications (ACS)
Alaska Communications (ACS), 2 APNs
Change Network Mode to LTE/GSM/WCDMA
Data APN:
Name: ACS Data
APN: web.acs
MCC 311 (Default)
MNC 370 (Default)
APN type: “default,supl” or “*”
MMS APN:
Name: ACS MMS
APN: mms.acs
MMSC: hxxp://mmsc.gci.csky.us:6672
MMS proxy: 209.4.229.92
MMS port: 9201
MCC 311 (Default)
MNC 370 (Default)
APN type: mms
Or the easiest way to do it would be just to edit the two current (GCI) APNs and change in the APN where ‘gci’ is listed to ‘acs’.
Change hxxp to http.
-Frozen
Hello,
having LTE issues (Not getting LTE) with Task & Ktoonsez AOKP rom, I have it set to LTE/GSM (PRL) mode (*#*#4636#*#* menu) and when I go into settings>More>Mobile Networks>Network Mode, I have it set to: LTE/GSM/WCDMA mode, and all I get is H and H+ still. I have the LTE APN and have it selected, and still no luck. I had a SIM replacement from Virgin Mobile, but it didn't do any good. When I put it on LTE only mode I lose connection to my carrier. So I keep it on LTE/GSM mode, but still getting no LTE. Anything I can do to fix this? Thanks. It used to work when I had Team Insomnia's Jellybean rom, I had 4g but got no where near LTE speeds. Would this be a Virgin Mobile problem?
Papaniz said:
Hello,
having LTE issues (Not getting LTE) with Task & Ktoonsez AOKP rom, I have it set to LTE/GSM (PRL) mode (*#*#4636#*#* menu) and when I go into settings>More>Mobile Networks>Network Mode, I have it set to: LTE/GSM/WCDMA mode, and all I get is H and H+ still. I have the LTE APN and have it selected, and still no luck. I had a SIM replacement from Virgin Mobile, but it didn't do any good. When I put it on LTE only mode I lose connection to my carrier. So I keep it on LTE/GSM mode, but still getting no LTE. Anything I can do to fix this? Thanks. It used to work when I had Team Insomnia's Jellybean rom, I had 4g but got no where near LTE speeds. Would this be a Virgin Mobile problem?
Click to expand...
Click to collapse
When you were on the TouchWiz ROM did it only say 4g and not 4g LTE? It would say 4g LTE in a TouchWiz ROM... You may not be in an LTE area...
Quasimodem said:
When you were on the TouchWiz ROM did it only say 4g and not 4g LTE? It would say 4g LTE in a TouchWiz ROM... You may not be in an LTE area...
Click to expand...
Click to collapse
Oh it only had 4G on it. I did check the map for Virgin and yeah I am in an LTE area. I don't know it may be a Virgin Mobile issue.
Sent from my SGH-I747 using xda app-developers app
Papaniz said:
Oh it only had 4G on it. I did check the map for Virgin and yeah I am in an LTE area. I don't know it may be a Virgin Mobile issue.
Sent from my SGH-I747 using xda app-developers app
Click to expand...
Click to collapse
If it only had 4G on it you were never getting lte in the first place... Might wanna call them.. . Do u mind posting your apn settings for the op?
Not sent from your phone...
Quasimodem said:
If it only had 4G on it you were never getting lte in the first place... Might wanna call them.. . Do u mind posting your apn settings for the op?
Not sent from your phone...
Click to expand...
Click to collapse
Sure..
Name: Bell LTE
APN: pda.bell.ca
Proxy: web.wireless.bell.ca
Port:80
MMSC: http://mms.bell.ca/mms/wapenc
MMS Proxy: web.wireless.bell.ca
MMS Port: 80
MCC: 302
MNC: 610
Authentication Type: Not Set
APN Type: Not Set
APN Protocol: IPv4
Bearer: Unspecified
EDIT: I think I got it, I am on a Virgin Mobile Supertab (From old phone still being paid off) and changed from that older phone, that didn't have LTE, to the S3 , I went into my Virgin Mobile "My Account' and it showed my phones it only listed the HTC Legend I had few months ago, but not the S3 itself, and beside it saying this device runs on a HSPA+ network. I'm getting this fixed on Monday so I'll see what happens then. If somebody can do it sooner though if they have the same issue with Virgin Mobile/Bell, that would be great too. The system I guess still thinks that I have the HTC Legend which doesn't run LTE.
Anybody on the Bell network having signal problems while running AOKP? I can't seem to get my phone to run LTE and my signal drops randomly. I've wiped, fixed permissions, enabled the proper settings and still nothing.
IUH1991 said:
Anybody on the Bell network having signal problems while running AOKP? I can't seem to get my phone to run LTE and my signal drops randomly. I've wiped, fixed permissions, enabled the proper settings and still nothing.
Click to expand...
Click to collapse
On the stock rom did it say 4G lte?
Not sent from your phone...
Constently Losing Signal On My S3 While On 3G Only APN pls help!!
Galaxy S3 AT&T 16GB rooted but never use the root nor made modifications im running Jelly Bean 4.1.1.
Below is listed two APNs that I use to get strictly 3G/4G network because I want to save my battery on my AT&T Galaxy S3 running Jelly Bean 4.1.1. I don't want my phone looking for nor connecting to the LTE network. But I run into the problem of constently losing signal randomly while running on either of the 3G/4G APNs I have manually set. After I lose signal my phone reconnects within two minutes back on to the 3G/4G network which is what I want it to do. But I dont want to have the problem of constently losing signal. I never lose signal when I have my APN set to the orignal APN that came already set on my phone which is called "ATT Phone".
When I do lose signal its not like im in a poor signal area. I have an iPhone 4S aswell and I never lose signal while I do on the Galaxy S3. The iPhone is on AT&T as well.
I live in Plano TX which is an LTE area
Are there other APNs I can try for AT&T? Do I have something set wrong listed on the two APNs listed below?
Any help would be appreciated,
Thanks
3G APN -
APN: wap.cingular
Proxy: Not Set
Port: Not Set
Username: [email protected]
Password: CINGULAR1
Server: Not Set
MMSC: http://mmsc.cingular.com
MMS Proxy: Not set
MMS port: 80
MCC: 310
MNC: 410
Authentication type: Not Set
APN type: Not Set
Bearer: Unspecified
3G APN 2 -
APN: wap.cingular
Proxy: Not Set
Port: Not Set
Username: Not Set
Password: Not Set
Server: Not Set
MMSC: Not Set
MMS Proxy: Not set
MMS port: Not Set
MCC: 310
MNC: 410
Authentication type: Not Set
APN type: Not Set
Bearer: Unspecified
A APN isn't what you need. Use your regular LTE APN but set the network mode to GSM/WCDMA preferred.
Hate to be the bearer of bad news...but this happened to me not too long ago. AT&T did a diagnostic on my phone and the sim connector was screwy. I had to send it in for repairs.
How would I set that?
BWolf56 said:
A APN isn't what you need. Use your regular LTE APN but set the network mode to GSM/WCDMA preferred.
Click to expand...
Click to collapse
I purchased an unlocked Verizon LG G3. I am trying to figure out what APN settings to use. I have searched all over and various other threads suggests different settings.
Here are the issues I have in most of the settings I've used: Poor signal, Internet but unable to download MMS, or no internet but text service. I also tried enabling roaming. So what settings do I use??
Here is what I have now:
Name: T-Mobile US LTE
APN: fast.t-mobile.com
Proxy: Not set
Port: Not set
Username: Not Set
Password: Not Set
Server:Not Set
MMSC:Not Set
MMS Proxy:Not set
MCC:310
MNC:260
Authentication Type: Not set
APN Type: not set
APN Protocol:IPv4/IPv6
These settings give me service but I am getting between one to three bars. When I used to get full bars on my t-mobile g2.
javydiaz97 said:
I purchased an unlocked Verizon LG G3. I am trying to figure out what APN settings to use. I have searched all over and various other threads suggests different settings.
Here are the issues I have in most of the settings I've used: Poor signal, Internet but unable to download MMS, or no internet but text service. I also tried enabling roaming. So what settings do I use??
Here is what I have now:
Name: T-Mobile US LTE
APN: fast.t-mobile.com
Proxy: Not set
Port: Not set
Username: Not Set
Password: Not Set
Server:Not Set
MMSC:Not Set
MMS Proxy:Not set
MCC:310
MNC:260
Authentication Type: Not set
APN Type: not set
APN Protocol:IPv4/IPv6
These settings give me service but I am getting between one to three bars. When I used to get full bars on my t-mobile g2.
Click to expand...
Click to collapse
On APN type add "default,supl,mms"
Without the quotes.
Sent from my LG-D800 using Tapatalk
xmayhemreturnsx said:
On APN type add "default,supl,mms"
Without the quotes.
Sent from my LG-D800 using Tapatalk
Click to expand...
Click to collapse
Thank you.
It seemed to get better, now it is staying at 3 bars, however now I have another issue. MY data is always on even if I disable it.
javydiaz97 said:
Thank you.
It seemed to get better, now it is staying at 3 bars, however now I have another issue. MY data is always on even if I disable it.
Click to expand...
Click to collapse
That is weird. I have not seen that before. I would recommend updating your phone if not updated to the latest version. If you are in the latest version you might have to factory reset your phone.
Sent from my LG-D800 using Tapatalk