[Q] Confused and terrified!!!! - Desire HD Q&A, Help & Troubleshooting

hello.. i just flashed the pacman rom for my desire hd.. PACman-v19.3-BLINDNDUMB..
i go to about phone and there i see that Memory is only 594mb.. what does this mean.. the original ram is 768mb.. why has it reduced??
please help!!!!
nor do i have the paranoid settings option in my settings menu.. its getting really weired..

your phone never got to use all 700 whatever. With every phone, due to hardware/phone restrictions you'll never get all of it. E.G. the Note 2, packing 2 whopping gigabytes of ram only gets to use around 1.7 of that. HTC Is a little worse off, its DNA gets only 1.5 usable of the 2 gigabytes.
If you go back to stock, and install a separate task manager you'll see that you probably only get 610-620 (I think htc just shows how much is free, not how much is system accessible). 610-620 because it varies ROM by ROM, however the difference is very minimal, and it shouldn't make a difference. If you're really worried about speed, try out the Supercharger script (google for it). It might look a little intimidating, but youtube will help, the script itself asks you everything in a logical manner, and more importantly, you probably won't be able to screw up- the script just changes values around, at worst you just won't notice a terrible amount of improvements.
I forget where paranoid settings are located, but it's probably there.
Finally, RELAX. If worst comes to worst, and you really screw up, you can just flash the original rom .zip on top, without having to wipe anything (if it gets even worse, you'll just have to backup your apps, wipe everything, and then restore them). Flashing ROMs are extremely safe, so long as you do everything right. Seeing that you successfully a ROM, and you were able to notice how much free ram you had, I would say you're better off than a lot of people.
But just in case, giving a full break down of what you did will allow us to know if you did indeed mess up somewhere along the way.

xxkid123 said:
your phone never got to use all 700 whatever. With every phone, due to hardware/phone restrictions you'll never get all of it. E.G. the Note 2, packing 2 whopping gigabytes of ram only gets to use around 1.7 of that. HTC Is a little worse off, its DNA gets only 1.5 usable of the 2 gigabytes.
If you go back to stock, and install a separate task manager you'll see that you probably only get 610-620 (I think htc just shows how much is free, not how much is system accessible). 610-620 because it varies ROM by ROM, however the difference is very minimal, and it shouldn't make a difference. If you're really worried about speed, try out the Supercharger script (google for it). It might look a little intimidating, but youtube will help, the script itself asks you everything in a logical manner, and more importantly, you probably won't be able to screw up- the script just changes values around, at worst you just won't notice a terrible amount of improvements.
I forget where paranoid settings are located, but it's probably there.
Finally, RELAX. If worst comes to worst, and you really screw up, you can just flash the original rom .zip on top, without having to wipe anything (if it gets even worse, you'll just have to backup your apps, wipe everything, and then restore them). Flashing ROMs are extremely safe, so long as you do everything right. Seeing that you successfully a ROM, and you were able to notice how much free ram you had, I would say you're better off than a lot of people.
But just in case, giving a full break down of what you did will allow us to know if you did indeed mess up somewhere along the way.
Click to expand...
Click to collapse
okay these are the steps i did to flash the rom..
1) boot the phone in recovery mode..
2) 4ext recovery.. so i do a 'wipe data+dalvik'
3)then i do a 'format all partitions(except sd card)..
4) then install zip from sd card..
these are the steps i followed..
i also do not have the gapps in the rom.. in the thread they said it was already there.. how to i change the screen turn off animation.. this rom is totally different from whats in the thread..

rajivkarai said:
okay these are the steps i did to flash the rom..
1) boot the phone in recovery mode..
2) 4ext recovery.. so i do a 'wipe data+dalvik'
3)then i do a 'format all partitions(except sd card)..
4) then install zip from sd card..
these are the steps i followed..
i also do not have the gapps in the rom.. in the thread they said it was already there.. how to i change the screen turn off animation.. this rom is totally different from whats in the thread..
Click to expand...
Click to collapse
You need to flash Gapps, it doesn't mention that it's included in the thread
http://goo.im/gapps/gapps-jb-20121011-signed.zip
Flash it normally, no need to wipe (although wiping cache+dalvik) should help.
for paranoid settings, check this post http://forum.xda-developers.com/showpost.php?p=32720700&postcount=4
Your flashing process was correct, so I don't think anything was wrong there.

Related

[Q] Wiping phone and starting over

I have been having all sorts of problems with my phone, mainly from it running super low on storage space, even though I have moved virtually everything to the SD card that I can, and keep wiping the address book (which of course screws everything up). Some kind folks had helped me out a lot, but in the end suggested I just wipe it all and start over, but I was waiting to get a new SD card, which I finally have, and I just wanted to make sure I understand everything correctly before leaping in.
So I understand I need to format the SD card, and I was hoping someone could give me or point me to a guide to doing so. I understand I need to get A2SD, is that right? And so once I format it, I can just put everything on my old card onto the new one, yeah? And I understand I need to install Amon RA and get rid of Clockwork Mod, I get that. So then after I do all that, I should just flash a new ROM and not restore anything, and if things seem better, then I can batch restore apps, is that right? I think I just want to stick with the stock ROM, but is there a rooted version of the latest update available?
If someone would be so kind as to walk me through this one last time, keeping in mind I am pretty much a noob, that would be much appreciated.
Oh, I also would love to do the Firerat custom MTD partitions thing (http://forum.xda-developers.com/showthread.php?t=855424), tried to do it once before but screwed some things up, had to revert back to a previous backup, so figured now would be a good time to try that again, so if anyone can give me the rundown on that too, that would be super.
Thanks so much!
im gonna try and help you here, first back up everything you have on your sd card to your computer so you dont loose it when partitioning, then download a PCIMG36.zip of amon ra, put it on sd card and boot into bootloader and select yes when prompted, that will put amon ra as your recovery. now that you have amon ra and already backed up the stuff in your sd card to your computer go ahead and in recovery selcect partition sd card, its gonna ask you for a swap size( i use 0 but you can use 32 if you like, 0 works fine), then its going to ask for partition size for me 1024 is more than enough(1024 equals 1gb), once this is done, select upgrade ext2 to ext3. now your sd card is partitioned. you can go ahead and put all your stuff back into your sd card and flash the rom(for a2sd to work your rom has to have it built in, other wise you are going to have to flash it) if your rom has it built in it will automatically kick in. once your rom is flashed you can go ahead and restore apps, i would do them one by one, sometimes there are issues when doing batch, and also unless the app is really important i would only restore the app not its data, but i do restore app and data for important apps. if all goes well you should have a lot more free memory on your phone, you can check if apps are going to sd ext by opening titanium back up and at the bottom you should see sd a2sd or sd ext and next to it amount of free memory, if your phone internal is still low after all this and gets lower when installing apps you can fix it by going into terminal emulator and typing
su (hit enter)
a2sd reinstall (hit enter, this will move all apps to sd ext)
any more questions ust ask
With the new 2.1/3.0 hybrids, you're better off using larger partitions. I found swap 64 or 128 and EXT of 2048 works out better, if you have an 8gig or larger SD Card
Thanks so much for the quick responses! I am going to give this a shot later tonight, but another quick question.
I think I've got down how to partition it, thanks a lot for breaking that down for me. And I did just get a 32 GB SD card, so I'll go with the 128 swap and EXT of 2048, that's no big deal.
Now for what ROM to flash - I've just used the stock before, haven't flashed any other ROMs, but if I'm going this far, figure I might as well give it a try, why not. So what ROM would you recommend that has A2SD already built in?? If you could just give me a quick run down (or point me to somewhere where there is one, I'm sure it already exists) on how to go about flashing the ROM (I think I just download it though and install it through bootloader, is that right??), that would be super appreciated.
Thanks again!!
Roms are flashed through recovery and what Rom to use wow that will get you a lot of opinions.
Sent from my PG86100 using XDA App
man there are so many roms for so many tastes, but i would suggest Vaelpak 3.2 rc2 which is still a sense rom, but has a lot of customization options. to flash your fresh rom you need to put the rom on your sd card, then turn off phone, go into bootloader, go into recovery, select wipe, and wipe cache, dalvik cache and data, do each twice to make sure, then go back and select flash zip from sd card, scroll to the bottom and look for the rom, select it and reboot
Once again, thanks for the replies and the detailed explanation, much appreciated. Didn't get around to it last night, will do so tonight. I definitely understand there are a ton of ROMs out there, but am just looking for something pretty simple I guess, since all I've used is the stock so far. Vaelpak 3.2 rc2 sounds good, I'll give that a try. So just to make sure I understand, when I install this ROM, that's everything, right, so I don't need to worry about installing the latest Android software. Or do I still need to install the latest Gingerbread update (and if so, how do I go about doing that?) in addition to installing this ROM?
Sorry for the million questions, and thanks again!
VaelPak is a very extensive ROM. If you REALLY want to stay close to stock, but have the most updated, complete, streamlined, error free experience, go with Synergy or MikG.
I LOVE VaelPak, but there is a LOT of options, themeing, development, etc in there. It's definitely not for a beginner. Also, his newest release, which is based in GB is pretty awesome, but it's an AOSP Rom, which I'm not a fan of.
Hi all,
So this is really strange, I feel like I must just be missing something, but I finally pulled the trigger, did it all, flashed my first ROM (exciting!) and all seems to have gone smoothly, except that I cannot figure out how to access Titanium Backup?!? I thought it came with MikG (I decided to give that ROM a shot), but did not see it, so went to the Market and re-downloaded it, and it says downloaded, but I cannot click on "open" and it is nowhere to be found in the apps list, or anywhere for that matter. Help! What the heck is going on? Any thoughts?
Thanks much!
Did you have a notification saying "Titatium Backup Installed" or something like that? I've had the same problem in the Gingersense roms if I leave the market before the download AND installation is complete. Not every time but sometimes.
I was just being a little slow there, I had installed the key, but not the actual program. Oops So all good, got that working, but a couple quick more questions.
Sadly it seems that I did not have TB set to backup everything on a regular basis, looks like it was just set up to backup new apps and new versions (yikes!, I know). So I've been restoring some apps little by little, and when I restored Angry Birds I noticed I was stuck back on the first level and I was like, this isn't right, looked at the date, and last backup was like March/April. This is kind of a drag for some things, like that, and especially beyondPod, lost all my settings and a number of feeds there, but I think it's probably just something I'm going to have to live with, right? I of course made a nandroid right before I wiped and flashed, but it seems like even more of a hassle to go back to that nandroid, backup things to Titanium, then reflash MikG and restore everything again, rather than just recreating what I've lost, right? Just wanted to make sure I wasn't missing something, there's no other way around this.
Thanks for any assistance.

[Q] Wifi not turning on! Please Help.

Hello, Im new to all of this so please understand. Okay, I have a Sprint GS3, I rooted it using the toolbox thing it worked but I decided that I didnt want the root anymore. I loaded stock software and booted it up normal. The only problem now is my wifi isnt turning on. Ive searched page after page on google, ask and bing. I dont know what to do anymore. Im just about to just say screw it and give up. Any help will be much appreciated.
You Odin'd back to Stock, and now your WiFi is not working correctly ? Are you certain your connecting to your Router ? Did you check the Router to make sure it's working correctly ? Did you try to connect to the Router with another Device ?
If you still have a custom recovery installed, I'd say to just flash another rom. The toolbox kills your WiFi fir sine reason, which can only be fixed by flashing another kernel, and roms have the kernels built in so, you might as well kill two birds with one stone
You could just flash stock rooted though, no need to go full out custom
Wifi not turning on
What I mean is my phone's wifi wont turn on at all. How do I get everything back to normal like before I rooted it?
Brblank44 said:
What I mean is my phone's wifi wont turn on at all. How do I get everything back to normal like before I rooted it?
Click to expand...
Click to collapse
Ok, this method should work and do exactly what you wanted, but you'll still have root access.
Below, I have quoted a post I made a while back when trying to help someone out.
Down below I link to Freeza's stock Rom, which is what you want if you want the stock phone with root. The one you want to download is the DeOdex MD4 one:
DeOdex:
Sprint Touchwiz Jelly Bean 4.1.2 L710VPBMD4 | Mirror
MD5: 77262D9D6CF1A6AF30A8981A95A75D57
Click to expand...
Click to collapse
In step #4, the wipe system is very important. It's most likely that something in your /system folder is messing up your wifi. Just flashing a new Rom over might not fix it. I'd also wipe /data, 'cause a fresh wipe is much less likely to have issues.
Ok, let's start at the very beginning (it's a very good place to start).
Before we get started, I'm going to make the following assumptions:
You successfully rooted your phone through Odin.
You currently have a custom recovery (either TWRP or CWM).
You have a Rom you'd like to flash on either your internal storage or your SDcard (I'd recommend the SDcard, but that's your prerogative).
If either of the first two is not true, I'd recommend going back to the rooting guide and check out the videos on how to use Odin to gain root and a custom recovery.
If number 3 above is not true, download a ROM (nor someone new to flashing/custom Roms, I'd recommend Freeza's stock rooted Rom, as it's identical to stock TW, but just with Root). Once you download a Rom, check it's md5sum to verify that it's a good download. Copy the file to your SD card and get ready to flash (make sure you have decent battery life left, I try to keep at least 50% or more when flashing Roms, although it shouldn't take too long.
I'll give directions on how to flash a Rom below. The instructions will be for TWRP, but CWM has similar options/settings
Turn your phone completely off (hold down power for 3-5 seconds)
Boot your phone into recovery. Hold Up, Menu, and Power for a few seconds (until SAMSUNG appears on your screen and the phone vibrates)
Make a Nandroid backup. I can't emphasize this enough. In flashing, it's almost a certainty that one time, something will mess up. When that happens, you want to be able to restore a backup. In TWRP, just go into Backup Menu and choose where you want it (internal vs. External storage). It takes my phone a few (5-10) minutes to completely backup my data.
In TWRP, click the wipe button, then system. This will completely wipe the Rom from your phone. Doing this will allow you to get a "clean" install, without any settings or leftover files from your old Rom getting in the way. Instead, you could only wipe data (factory reset), which is good enough for most Roms. I'd still recommend a system wipe, though.
Also while in the Wipe menu, wipe Cache and Dalvik Cache.
Go back to the TWRP main menu.
Click Install, then find your Rom zip file (may have to switch from internal to external storage).
Let TWRP do it's thing.
If you're installing a TW-based Rom, chances are it had gapps already installed. If not, you should now flash the correct gapps package from goo.im. Make sure you're flashing the correct one, as if you don't, your google apps will force close upon use.
Reboot into system and give it time to boot (first boot sometimes takes a couple of minutes).
Set up your phone the way you like.
These should be the directions to follow whenever you flash a new Rom. Some Roms have the Aroma installer, so you'll have more options once you choose to flash the Rom zip, but those are typically easy to follow (and vary from Rom to Rom, so I won't be able to give you a good guide on that).
Hope this helps!
Click to expand...
Click to collapse
Brblank44 said:
What I mean is my phone's wifi wont turn on at all. How do I get everything back to normal like before I rooted it?
Click to expand...
Click to collapse
Yes. The toolbox kills your WiFi completely and you have to flash another rom to fix it. Flash stock rooted from freezas thread and you should be good to go.
CNexus said:
If you still have a custom recovery installed, I'd say to just flash another rom. The toolbox kills your WiFi fir sine reason, which can only be fixed by flashing another kernel, and roms have the kernels built in so, you might as well kill two birds with one stone
You could just flash stock rooted though, no need to go full out custom
Click to expand...
Click to collapse
Why do people use a toolbox on a phone that's so easy to root without it?
flastnoles11 said:
Why do people use a toolbox on a phone that's so easy to root without it?
Click to expand...
Click to collapse
When I first rooted my phone (back pre LJ7 days), I used it because I came from the EVO 4G, which was notoriously difficult to root (and which needed a toolkit). So when I came to the GS3, I figured it'd be the same way. Fortunately, the toolkit worked better back then and I didn't have an issue. Now that I've helped others use Odin (and have used it myself a number of times), I don't point to the toolkit anymore.
But my point is, sometimes people assume it's difficult, see a toolkit that is meant to make it easier and decide that's the way to go.
topherk said:
Ok, this method should work and do exactly what you wanted, but you'll still have root access.
Below, I have quoted a post I made a while back when trying to help someone out.
Down below I link to Freeza's stock Rom, which is what you want if you want the stock phone with root. The one you want to download is the DeOdex MD4 one:
In step #4, the wipe system is very important. It's most likely that something in your /system folder is messing up your wifi. Just flashing a new Rom over might not fix it. I'd also wipe /data, 'cause a fresh wipe is much less likely to have issues.
Click to expand...
Click to collapse
Thank you very much. I will try this as soon as I can.
topherk said:
When I first rooted my phone (back pre LJ7 days), I used it because I came from the EVO 4G, which was notoriously difficult to root (and which needed a toolkit). So when I came to the GS3, I figured it'd be the same way. Fortunately, the toolkit worked better back then and I didn't have an issue. Now that I've helped others use Odin (and have used it myself a number of times), I don't point to the toolkit anymore.
But my point is, sometimes people assume it's difficult, see a toolkit that is meant to make it easier and decide that's the way to go.
Click to expand...
Click to collapse
I get that, but just a tiny bit of reading around well show you the toolkit is actually the harder way to root this phone in my opinion... Just saying
flastnoles11 said:
I get that, but just a tiny bit of reading around well show you the toolkit is actually the harder way to root this phone in my opinion... Just saying
Click to expand...
Click to collapse
I totally agree that the toolkit is much more complicated and a bit of a "black box." Hence why I don't recommend it anymore.
But back then, even though I read a whole lot, I decided to go with the toolkit because it felt safer. Heck, I eevn donated so I could get the "pro" features! And for people who aren't that comfortable "hacking" things, it's tempting to use something that'll do the "hard work" for you, even if the normal way of doing it is relatively simple.
That's why I always try to spell things out very clearly for people (I do like numbered lists, don't I?). If someone responds to a thread with "just wipe data and flash a new rom," most "noobs" will hesitate because while they may know those terms, they don't know the procedure and will be afraid of messing it up. With the numbered list of instructions, they typically feel much more comfortable with doing it themselves.
Just my two cents.
Yeah, very true (@topherk). The first time I rooted my firdt phone, I saw all the guides and stuff, but settled on a toolkit sort of program to do it for me...subsequent phones I've always rooted by hand. For me it kinda sucks that there's no way to root the S3 manually (as in like, push this to.the phone, reboot, run this command then flash recovery)
Having come from 2 HTC devices (evo and evo shift), I kinda feel like ODIN is a "cheating" way to root lol. But that's just me.
Whats a md5? It says no md5 file and gives me an error.
Brblank44 said:
Whats a md5? It says no md5 file and gives me an error.
Click to expand...
Click to collapse
Thats normal,.the great majority of flashable zips do not include an md5 file.
What that is referring to is a hashing function, called the md5sum, that can be used to verify the integrity of a file. Most devs will provide this (in number format) so that you can check the md5sum of your local copy/download against what they provide. If anything goes wrong in a download or file transfer, the md5sum of your copy will not match the expected value, confirming that it was a bad download or that something went wrong along the way.
For your case, TWRP always checks to see if the flashable zip includes an md5sum check file that it can check your file against as an added precaution that you're not flashing something corrupted.
Brblank44 said:
Whats a md5? It says no md5 file and gives me an error.
Click to expand...
Click to collapse
Don't do the md5 verification in the Recovery. That typically fails, even if the md5 is correct.
I typically do it in Windows (I use this program, works great). If it's a really large file or I don't feel confident about the cable I'm using, I'll also check the md5sum in ES Explorer on the phone after I transfer it.
Okay I flashed it and I have the same problem. Wifi not turning on. The detox whatever its called didn't work. So I took it to sprint today after having flashed it and everything and they did a hard reset. I lost everything. Sprint couldn't swap the phone out for a new one. I am thinking about sending it back to samsung. So they can fix it. Any other ideas guys? Also thank you for your understanding and helping me.
Brblank44 said:
Okay I flashed it and I have the same problem. Wifi not turning on. The detox whatever its called didn't work. So I took it to sprint today after having flashed it and everything and they did a hard reset. I lost everything. Sprint couldn't swap the phone out for a new one. I am thinking about sending it back to samsung. So they can fix it. Any other ideas guys? Also thank you for your understanding and helping me.
Click to expand...
Click to collapse
Brblank,
Try this easy method to return to stock everything including recovery, flash count reset and device status normal. It worked perfectly for me.
Before flashing wipe Cache and Dalvik and factory reset.Then flash the file. Make sure you choose the correct file (16gb or 32gb version).
Even if it doesn't fix your WiFi issue it will put your phone in the proper state to send to Samsung.
You can place the file on your internal or external card.
Return to Stock Link
With much thanks to billard412
Hope this helps you.

Storage issues help

I'm suddenly having storage issues with every ROM that I flash after running a ROM with some script that isn't widely used.
First I'll give you a brief idea of my problem. I"m running out of storage and get notifications from the market saying as much after I download and reasonable amount of apps. The thing is... It show's I have used 738MB of ext4 out of 1.5 so that isn't the issue. The problem is internal memory. My phone won't move dalvik cache for some reason. When I run any ROM with a2sd or m2sd they both say that there is a problem and leave the dalvik cache where it is.
I think my internal folders are jacked up from 40ad2sdx or a zip that was used to clear memory before the ROM. There was a ext4 superwipe cleaner to load before the ROM. I did that without researching first. When I did go looking for the thread about it, it plainly said that it was for one phone only, and it wasn't my phone. I believe it was the Galaxy S3, but I can't be certain. It was a week ago. It was advised not to use it on any other phone because part of what it did was reset the internal folders. Does this mean I can now flash a ROM for the galaxy s3? Lol Just kidding.... Seriously, the second part is all my speculation and I have been wrong many times concerning android. Will somebody help me get my phone back in oem condition please?
Okay, I'm not even sure what you did here, because not knowing the script, anything could have happened.
Try wiping everything and flashing stock rooted here, then go from there with other roms after that.
If that doesn't work. Here's what I would do. It might be a major pain, but it is almost a surefire fix.
Unroot and return to stock, then root again.
[UNROOT]
[ROOT]
For future reference, NEVER flash anything that is meant for another device. (Obviously, if it's a port then you're ok.)
ALSO EXTREMELY IMPORTANT: Backup your SD card, and wipe that puppy clean!! Only partition using Amon-RA recovery, otherwise it will screw you up quite often. I repeat, if you do not have the partition done correctly, then odds are that A2SD or equivalent won't work.
nate234 said:
Okay, I'm not even sure what you did here, because not knowing the script, anything could have happened.
Try wiping everything and flashing stock rooted here, then go from there with other roms after that.
If that doesn't work. Here's what I would do. It might be a major pain, but it is almost a surefire fix.
Unroot and return to stock, then root again.
[UNROOT]
[ROOT]
For future reference, NEVER flash anything that is meant for another device. (Obviously, if it's a port then you're ok.)
ALSO EXTREMELY IMPORTANT: Backup your SD card, and wipe that puppy clean!! Only partition using Amon-RA recovery, otherwise it will screw you up quite often. I repeat, if you do not have the partition done correctly, then odds are that A2SD or equivalent won't work.
Click to expand...
Click to collapse
I did the wipe and flash to stock earlier today, then flashed the Pac man ROM but the issue is still there. I had looked at unrooting my phone earlier today also. I'm glad to read this because it lets me know that I do have some idea of what to do. Thanks for the reply. I'll post here again with the results. Check back soon.
EDIT----> Man, my phone is okay. I loaded up a fairly recent ROM by Tronit, and it worked fine. It was the ROMs. Just to be sure, I went back to the last two ROMs just to see, and they did the same thing again. Now I'm on the AOKP Unnoffical and it's working just fine. The a2sd is working perfectly like it should, and my dalvik cache is moving to ext4. It was just coincidental that the last three ROM's I loaded all have issue with the a2sd. It's funny how nobody else see's problems but me. I looked in the bin file of one of them and it's missing part of the a2sd file. The other two have weird init.d files that I don't know anything about. I'm assuming the a2sd problem is related to that. It's funny how I see lots of problems, and report them, but I get blown off by some people as a noob who is making mistakes. I am a noob, and I do make mistakes, but I know some of my theories about problems are correct...... I gotta get me some respect by compiling my own ROMs.
Status update..... My phone is jacked up for sure. It does work with the AOKP Unofficial by Tronit, but this morning when I cleared my cache with Smelkus Recovery, it had major problems with almost every app. Clearing the cache in recovery is something I've done with every ROM and this has never happened. I uninstalled all the apps and reinstalled them. Got them working again. Everything seemed to be okay. However, when I cleared my cache with Android Tuner, again it ruined every app. I've used android tuner every day for two months to clear the cache and never had problems like this. Something is very wrong.
*****edited and deleted for the sake of peace*****
Long story short, I flashed something made for another phone. I can't explain why I did this without taking up lots of pages, and it doesn't even matter really. Lets just focus on the solution. Here is the link. I flashed both of the zips in the link.
http://forum.xda-developers.com/showthread.php?t=1477955
So I think my permissions for the files on my phone are out of whack. Is that what I"m reading is the possible outcome of flashing these if your phone is not the one listed? Please post your thoughts. I need them.
Try backing up your SD card on a computer and format you SD card and repartion it
Sent from my PC36100 using Tapatalk 2
g2435 said:
Try backing up your SD card on a computer and format you SD card and repartion it
Sent from my PC36100 using Tapatalk 2
Click to expand...
Click to collapse
I did that. Both with Smelkus, and Mini partition wizard. Same problems. I just tried to fix permissions with smelkus 4.3 on the AOKP Unofficial ROM and it took a minute for it to do it's thing. The line of dots was two full rows. So when It loaded back up, I suddenly see the same disk Icon in my notification bar, and now this ROM says it it out of memory. Man, it was working fine. I had twenty more apps on it too and I uninstalled them. It was working fine then, so with twenty less apps, it shouldn't suddenly say "Running out of Storage space."
I have told you this already: Please do not flash things meant for other phones, it could mess up. If it's meant for another device, it might screw yours up. To stay on the safe side: If it's not generic (works for every Android phone) or phone specific (exclusive to the Evo 4G) then don't flash it.
nate234 said:
I have told you this already: Please do not flash things meant for other phones, it could mess up. If it's meant for another device, it might screw yours up. To stay on the safe side: If it's not generic (works for every Android phone) or phone specific (exclusive to the Evo 4G) then don't flash it.
Click to expand...
Click to collapse
I flashed this about a eek ago, when I was looking for the ext4 wipe. I thought it was the same thing as another zip despite what it said. Stupid... I know. I think this may be the cause of my problems, but I can't be sure. I don't know at all really. Just speculations. I reflashed the CWM touch and used to flash a stock ROM. Gonna try that again. I ran the test on CWM touch and it said that the
/sys/class/android_usb/android0 was missing and unable to perform the test. Can this be the cause of my problems?
Don't beat yourself up man, it was an honest mistake, just learn from it and you'll be alright.
Now the optimal recovery for this device would be the Amon-RA recovery, and I recommend redoing what I said in my first post once you have Amon-RA installed. Amon-RA is an awesome recovery, and it's super easy to install. Check out this easy-to-follow video on how to install by clicking here.
Do that, then do what I said in the previous posts. Let me know what happens, because I'm almost certain this should work.
nate234 said:
Don't beat yourself up man, it was an honest mistake, just learn from it and you'll be alright.
Now the optimal recovery for this device would be the Amon-RA recovery, and I recommend redoing what I said in my first post once you have Amon-RA installed. Amon-RA is an awesome recovery, and it's super easy to install. Check out this easy-to-follow video on how to install by clicking here.
Do that, then do what I said in the previous posts. Let me know what happens, because I'm almost certain this should work.
Click to expand...
Click to collapse
I tried loading the Pacman ROM again with CWM and it wouldn't even load. It gets stuck in a bootloop. After that I flashed smelkus and went back to the Stock Rom.
*****edited and deleted for the sake of peace****
RADIO EDIT------
Sent from my PG86100 using xda app-developers app
edited and deleted for the sake of peace
As I stated in my pm give me a day or so till I get back home and I will check into a fix for you. Only don't expect any one on one help. If the fix works cool if not I will dig further. TNN strives to help with any issue no matter who is at fault. I will look at the wipe script you flashed and see if it can be undone. Just be prepared of the possibility that your phone may never work correctly again.
Sent from my PG86100 using xda app-developers app
I was finally able to get my phone straightened out. I loaded up a stock ROM then decided to use my SD Maid to look around. I found a file with completely different dates on it, but it wouldn't let me remove it. I ended up copying everything else in the subfolder and then deleted the parent folder. Then added everything else back. Wah lah.... magic. I don't know what that file was or where it came from but it was killing my internal memory. I'm wondering how it stayed from ROM to ROM. I dunno, but it's gone, and the Pacman ROM is lovely now. BOOM!!!!
jlmancuso said:
As I stated in my pm give me a day or so till I get back home and I will check into a fix for you. Only don't expect any one on one help. If the fix works cool if not I will dig further. TNN strives to help with any issue no matter who is at fault. I will look at the wipe script you flashed and see if it can be undone. Just be prepared of the possibility that your phone may never work correctly again.
Sent from my PG86100 using xda app-developers app
Click to expand...
Click to collapse
Whatever I did only fixed part of the issue. I'm left with in a situation where every time I go into recovery my downloaded apps stop working. It is cutting part of them off whether I clear cache or not. All I have to do is power off into recovery, and when I reboot, all of my downloaded apps begin giving messages that "Unfortuately such ans such has stopped." My phone becomes inoperable. The only way I can keep it working is to send a new launcher to my phone from the market, let it install, then open it up and uninstall all the downloaded apps. I'm pretty sure this is an easy fix for someone like you Mancuso. I have a logcat and it show LOTS of errors that I have never seen before on any of my other logcats. What are my options? Tell me what to do to get my phone back to absolute OEM and then I'll reroot. UNLESS you know of some fix.
I've supplied a logcat from Catlog if you or anybody else wants to have a look. I'd really appreciate some help here. I love my Evo and I love learning this stuff. If somebody can help me positively identify the problem, I can most likely figure it out from there. Please give me your suggestions here. I'm nothing without some guidance on this. It's way out of my scope.
I've included a link to the ext4 script wipe that I used. How I got to this page, I do not know. However, I ran it because this page said it COULD POSSIBLY work on other phones despite the fact that it was made for another phone.
http://www.xda-developers.com/android/darkside-super-wipe-easily-wipe-partitions-when-flashing-roms/
And I flashed both zips from the thread that the story links users to. Here is the link for the two zips.
http://forum.xda-developers.com/showthread.php?t=1477955
I'm not sure this is the problem. I'll try to find the Vold.fstat thread that I tried on my own before you came up with the 40ad2sdx solution for the MIUI ROM.
This is the memory fix I tried as mentioned above.
http://forum.xda-developers.com/showthread.php?t=2246909
Please note that you see before and after pics of sd storage. You can see that my pics clearly resemble the after pics shown in this thread. I believe this is my problem. How can I undo this?
This post reflects the only things I did outside of normal flashing. My problem is here somewhere...
The fix you used is for samsung devices. That could have caused your problems.

Virus???? Idk but phone is messed up

Ok here it goes. my network service is off so i use my droin inc for games and such. running custom rom wildstang83 IceCream Scencless 1.0. im not sure what happened to my phone but i left for 3 days and come back to my phone being totally jacked up. It wot dl apps the google play reverted back to the old market icon. wont save my passwords for google sighn in. every time i go to youtube it says to re dl the google play services. im sure other stuff is messed up too. i have tried to flash another rom but when it gets loaded back up it keeps saying process. whatever failed and there a bunch of those that loop and i have to pull battery. when i try to factory reset it says everything was formatted but when i reboot phone its the sme as it was before apps and all. So is there anyone out there who can help me with this. Sorry if i posted in the wrong place or what not. i wasnt sure where to post it cuz its kinda an advanced question but not really a question just need help.
not a virus but it does sound like your phone might have exhausted all the space in the /data folder. I had a similar thing happen to me before I rooted and fixed my phone where i exhausted the space, itt went a factory reset and put the phone into an unusable state.
i don;t know anything about the rom you are running but are rooted and have CWM installed? if so, you should be able flash a new ROM to your device, GAPPS and optionally, the low space disk fix.
tekweezle said:
not a virus but it does sound like your phone might have exhausted all the space in the /data folder. I had a similar thing happen to me before I rooted and fixed my phone where i exhausted the space, itt went a factory reset and put the phone into an unusable state.
i don;t know anything about the rom you are running but are rooted and have CWM installed? if so, you should be able flash a new ROM to your device, GAPPS and optionally, the low space disk fix.
Click to expand...
Click to collapse
Yes i do have cwm but i tried to flash a new rom via the recovery section. after i choose the zip to flash everything goes as expected untill after the reboot and it goes into the setup part where u have to put gmail password and stuff in then it basically freezes up with unlimited process failures. but i will try again. cant hurt from where it is now.
if you are not doing so already, i would wipe cache and dalvik cache after flashing the rom. that may fix the FCs.
I would also suggest you run a newer jelly bean ROM like Tiny;s 5-16 with his version of GAPPS(4-05) version plus the low space disk fix so you can maintain parity with what is the latest.
I am currently using evervolve 6-25 and it is working well for me.
the reason I say that is these newer JB roms have the ability to let you skip the activation easily. I don;t know if it was some feature of GB roms but the activation wizard in the JB roms seem to be better my opinion.
When switching to a different ROM, it is crucial to wipe /system. This can be a source of FCs. Also, if switching, it is also a good idea to do factory reset.
tekweezle said:
if you are not doing so already, i would wipe cache and dalvik cache after flashing the rom. that may fix the FCs.
I would also suggest you run a newer jelly bean ROM like Tiny;s 5-16 with his version of GAPPS(4-05) version plus the low space disk fix so you can maintain parity with what is the latest.
I am currently using evervolve 6-25 and it is working well for me.
the reason I say that is these newer JB roms have the ability to let you skip the activation easily. I don;t know if it was some feature of GB roms but the activation wizard in the JB roms seem to be better my opinion.
Click to expand...
Click to collapse
I just flashed another rom i used in the past by the same dev and so this is my step by step. 1. choose zip from sd. 2. factory reset. 3. wipe dalvik cache. 4. wipe cache partition. If this doesnt work i will try jb roms but i would hate to have to dump the dev that im useing. there the most stabe roms i have come across so far
PonsAsinorem said:
When switching to a different ROM, it is crucial to wipe /system. This can be a source of FCs. Also, if switching, it is also a good idea to do factory reset.
Click to expand...
Click to collapse
what do u mean wipe /system. where do i find that. only reason i ask is cuz maybe ive never done that. but i have never had a problem withthe other 15 roms i have flashed before so thats why im so confused about what happened to my phone. all i did was shut it off and leave it home. nothing changed from my daily use before that and it was working top notch before i shut it off
im getting settings fc. youtube fc, my uploads fc, market fc, clock widget fc, internet fc, rss reader fc, htc sence fc, all those off of a fresh flash ad new sd card
Just lost my bckups that were saved on sd card so now i cant even get on it i dont get it. its not bricked but yet it i unstabe to run any rom but the preivious saved backup (now there deleted)
maybe the rom you downloaded is corrupt. worst case scenerio is that your phone is on it;s last legs.....
i would suggest you try downloading the JB rom and Gapps plus the low space fix.
http://forum.xda-developers.com/showthread.php?t=2050930
it;s kind of proven to work in my opinion. the 5-16 build is pretty stable.
what I do is flash the rom zip, gapps zip and low space zip, then wipe cache and dalvik. it probably should not make a difference but I am using TWRP as my recovery instead of CWM.
goodluck!
tekweezle said:
maybe the rom you downloaded is corrupt. worst case scenerio is that your phone is on it;s last legs.....
i would suggest you try downloading the JB rom and Gapps plus the low space fix.
http://forum.xda-developers.com/showthread.php?t=2050930
it;s kind of proven to work in my opinion. the 5-16 build is pretty stable.
what I do is flash the rom zip, gapps zip and low space zip, then wipe cache and dalvik. it probably should not make a difference but I am using TWRP as my recovery instead of CWM.
goodluck!
Click to expand...
Click to collapse
Thank u and its still not working. probably just takeing a dump on me now it is just bootlooping.
when i do a factory reset i get a wipe completed. but it says "no app2sd partition found. Skipping format of /sd-ext" could that be part of the issue?? ive never noticed that before
i don;t know if switching to TWRP might help you but it might be worth a try. maybe a coincidence but the last time I had a screw up on my Dinc installing a ROM, i was using CWM. I switch right after that. I think i did read something about TWRP specifically supporting the EXT4 Low space fix.
maybe someone more knowledgable can chime in.
tekweezle said:
i don;t know if switching to TWRP might help you but it might be worth a try. maybe a coincidence but the last time I had a screw up on my Dinc installing a ROM, i was using CWM. I switch right after that. I think i did read something about TWRP specifically supporting the EXT4 Low space fix.
maybe someone more knowledgable can chime in.
Click to expand...
Click to collapse
i will try it but it is doing the same thing on every rom i have tried to flash. ive tried 6 different roms so far and i have ran them all in the past so im incined to think its jacked. and is there a specific twrp for the different roms or can i just dl the latest version and it will work

[Q][CM 11 Xperia Arc S] How to enable ART mode on Kit Kat?

I tried to enable it in developer options but after reboot it gets stuck on boot logo spinning that arrow. First time i waited half an hour now whole hour, nothing happens. I had to do factory reset and wipe all to boot up.
Anyone else tried this?
DjDexter5GHz said:
I tried to enable it in developer options but after reboot it gets stuck on boot logo spinning that arrow. First time i waited half an hour now whole hour, nothing happens. I had to do factory reset and wipe all to boot up.
Anyone else tried this?
Click to expand...
Click to collapse
Read the CM11 thread, it has been discussed there quite a few times, with multiple (possible) solutions posted. Use Search tool if necessary.
Someguyfromhell said:
Read the CM11 thread, it has been discussed there quite a few times, with multiple (possible) solutions posted. Use Search tool if necessary.
Click to expand...
Click to collapse
Eventually, i found out there were newer builds which work. In case anyone else has same problem. (Always dl newest one!)
Yes, the new build's partition have been updated so that ART can be activated. Nevertheless, the dev warn you that ART is still in alpha stage, that's why it was not natively implemented in KK as the original runtime. More and more apps are being updated to support ART but on our old device, it is recommended to stay on Dalvik for now.
The problem with ART is that it's still in a testing stage, even on new models that get 4.4 as legit release.
We don't have enough cache to run it smoothly enough, and of the few people that did turn it on, most of them either saw no difference in the devices performance or thought that it was so minimal that it could well have simply been a placebo.
We all want the latest garb but there is always a point at where a line is drawn...
Funnily enough, most people that ask about ART clearly show within their reply bodies that they don't know anything about Android except how to flash a rom :-s
Nathan
Well I am not dumb as I may look, but only drawback I found for now is that I am running low on internal memory. Phone battery lasts for 3+ days in comparison with dalvik where it held for about a day, and everything runs much smoothly.
Mike says its not possible right now we only can wait right now but arc dont have much memory in data thats problem
AOKP Rom with ART enabled
It is very well possible to use KitKat 4.4.2 on our phones. Even with ART-runtime enabled. I personally use AOKP (Android Open Kang Project)'s KitKat version, and I managed to get ART-runtime enabled and running very fast and smooth.
You can find the ROM here: http://forum.xda-developers.com/show....php?t=2624761
Of course you have to first install the kernel, which is given in the zip-file. Just unzip the kernel and Flashboot it to your device. Then go into CWM-recovery and go to Mounts and Storage and activate USB-mount. Locate the full AOKP-zip and place it on your SD-Card, as wel as the minimal Gapps for 4.4.2., found here : http://forum.xda-developers.com/show....php?t=2012857. Unmount the USB, and install the zip as usual through the menu for it. Then, after installing AOKP, install the minimal Gapps.
Reboot and let your device sit for a while, or play around with it a bit....
I proceeded with installing Mounts2SD from playstore, while before having prepared my class10 8 Gb sdcard into two partitions. One partition FAT32, size about 6Gb and one partition EXT2 size around 2 Gb. Move everything to SD-card through the menu of Mounts2sd, except Dalvik-cache. NEVER MOVE THIS!!! (Don't move dalvik-cache to SD...)
Reboot at least two times to let the script (Mounts2sd) settle in... After this I installed Pimp-my-Rom from playstore and activated the nav-bar and some other scripts to improve the experience. Also I odexed (after finishing all my modifications) the phone through this : http://forum.xda-developers.com/show....php?t=2527732
I then went to CWM-recovery through a reboot and made a full backup, which I advice you to do also, in case something goes horribly wrong.
Reboot to AOKP. As you can see, this ROM is awesome-fast beyond belief already. I had benchmarks in AnTuTu of around 6000, with NoFrills-CPU at 1401 Mhz. But, it can be faster if you choose to run ART-runtime instead of Dalvik. Be sure to remove all unwanted programs before switching to ART-runtime, because it'll take a lot of space in cache, and every program you don't need (system-programs that is) will reserve more space for ART.
Only and ONLY if your system is running smoothly on Dalvik, I advise you to go to your Phone-settings, (under Settings of course) and tap on 'Build-number' like 10 times. You will now become a developer. An extra menu will appear under Settings, where you can choose to run the ART-runtime library. Choose this and you will reboot.
Wait, wait and wait a long time for reboot. After initial booting everything has to be updated to ART-compiled apps. This will take a long time per app. Just wait and don't disturb your phone. If you get to the phone after booting, then you probably succeeded... You can check under the same settings-tab under Developer-options. If ART is selected, then you have it.
I strongly advice in case of mishaps regarding loss of network etc. to just reboot. Wait, wait and eventually you'll get there. Make a backup as soon as you have a stable working system under CWM-recovery.
I have been running stable ART under this AOKP-rom for about two weeks now and I'm really happy with it. Not only is the phone lightning-fast (6417 under AnTuTu, with CPU on my Arc LT15i on 1401 Mhz), but smooth as hell! Batterytime is amazing. This is as fast as it's gonna get! (I must have tried almost every ROM out there from stock 4.0.1 to 4.4.2...)
Hope you'll try and may it work for you too...!
(BTW my ultimate thanks to the guys from Open Kang Project!)
P.S. stock-browser is lagging... as usual under 4.4, but I use Dolphin and it is fast! Some toggles require reboot to function again. Some programs might fail you due to not being ready for ART. Facebook is a mess for instance, sometimes quitting, getting unresponsive etc. Otherwise I have encountered no problems whatsoever, albeit that memory is low of course and a minimality of (system-)programs should be installed for a good functionality of the phone.
It's really important for LT15i owners, to flash the stock software for LT18i (ARC S) onto your device, at least once, before installing any custom rom, because it removes the vendor-partition, which will give you an extra 40 Mb I'm told. Also partition your SDCARD before installing the AOKP-rom, as it will use the sdcard to store information on which will be deleted when you partition your card.
mhadjih said:
It is very well possible to use KitKat 4.4.2 on our phones.
Click to expand...
Click to collapse
can confirm, i have used art on xperia arc s with carbon rom nightly from 25.3.2014 with the included kernel, and micro gapps package from paranoid android. just flashed, activated art, rebooted and waited over 9000 hours. confirmed art was enabled in the developer options.
i think it was faster afterwards, i am not sure though. it seemed to be easy on the battery, too, but again, i didn't do any benchmarks or run a battery monitor so it could very well be that everything was in fact worse ^^
what i really noticed though: i had almost no internal memory for apps left. even after installing link2sd and linking all user apps, i still had not enough room to install all the apps i consider essential (10-20 apps maybe?).
i am now back to running on dalvik, the small internal memory of the arc s doesn't seem to lend itself to the art runtime very well.
yes, i know that there are gapps packages which are only 20 mB compared to the 80 mB of the pa-gapps package, still, even with a core gapps, those 60 mb don't mean very much with art running...

Categories

Resources