[Q] Regarding the S3 Unlock Method - AT&T, Rogers, Bell, Telus Samsung Galaxy S III

Not trying to sound noobish but need assistance on this Unlock Method that was posted here http://forum.xda-developers.com/showthread.php?t=2014982&page=1
Using the AT&T Samsung Galaxy S3 SGH-i747 version, the method worked however here is the dilemma.
I pre-emptively ordered an unlock code from an unlocking site. However, I stumbled across the above thread this morning and performed the procedure which worked and switched over to T-Mobile Prepaid. Given I heard T-Mobile is "re-farming" their network now, I am getting EDGE speeds. I've tried several different APN settings I've found online however it does not assist at all, when I run SpeedTest it comes up with an almost 500ping with .10mbs down and .10mbs up.
I'm looking to revert the procedure, which I went through the "common sense" method of going back in and doing the procedure to cut the "lock" back "on" however when rebooting the device still picks up the T-Mobile SIM and goes right back to their network, preventing me from accessing the Network Code Screen because I would like to go ahead and enter the unlock code I paid for just to have things done the "legit" method.
Things I've noticed on other forums about this method used. After doing so when you have no sim installed it will come up with a no sim card installed alert however I'm showing full bars even when a sim card is not installed.
One thing I have not tried was to reinstall my StraightTalk sim then performing the procedure to see if that will kick it back, will try later this evening and update this thread to show results.
Please help?
Running AT&T Samsung Galaxy S3 SGH-i747
Rooted/Custom Rom, Model now shows it is an SGH-T999(Even though the Hardware is actually i747)
Android Version 4.1.1
BB Version i747UCLH9
Build# FreeGS3_R7.1_Resurrection

Related

Can't fully install stock ROM with Odin - help please!

Hi, and firstly, thanks to any and all who offer their knowledge to assist my conundrum.
I recently purchased a Bell Canada version of the SG Note 2 (i317), I am on Telus so I attempted to Unlock the phone. I looked online and found people were having success unlocking these phones for free using the *#197327640# method, (whereby you go into the service mode, turn off the PERSHO_256 and then INITIALLIZ).
I tried this method and the phone then seemed to work with my telus sim, but only for voice, not data. When I put in a Bell SIM from a friend, both voice and data worked fine - which tells me its not a hardware (radio) issue. I also tried using another friends Telus SIM and had the same results as mine - which tells me it's not a SIM error. Also, all the settings in the mobile network area appeared to be correctly set up.
So, my next step was to try and reflash the phone to the stock Bell ROM and then just buy an Unlock code. I downloaded the stock ROM (2 different ones actually) and used Odin 3.07 to reload the ROM. I've tried it several times now, with both Bell ROMs and each time it says it's been successful, but the phone remains in the same, partially unlocked state.
It seems as though by using the PERSHO_256 method I have permanently, PARTIALLY unlocked the phone. I can't seem to re-lock it by installing the stock Bell ROM, and since it's unlocked, I can't get the foreign SIM error to come up to enable me to put in my purchased unlock code.
If anyone has any insights, it would be GREATLY appreciated. Thanks!
-Luke
did you check and/or setup the apn? it may be just the apn is not set correctly or you have to manually input hte apn
sounds like just APN needs setting...
APN?
How would I check/setup the APN? Is this to allow me to do a full reflash to a stock ROM or to access data with the phone in it's current state?
left ownsho
So I went into ACCES POINT NAMES and checked the sp.telus.net box, no change. Did a restart. No change Any ideas?
Wooooo Hooooo!!!
So, it's working now!!! I dug a little deeper and found the correct APN settings for TELUS. NOW IT F*@^&#*&@ING WORKS!
Thanks so much for pointing me in the right direction!!!

[Q] SGH-T889 Metro PCS sim not working

Hello,
Today I bought a Note 2 on Craigslist. Since it was from TMobile I though it was only a matter of putting my sim card in the phone and it would work, I was wrong. The person that I bought the phone from gave me an unlock code that he got straight from T-Mobile, however when i used my sim card the phone didn't ask me for the code, so I assumed it was already unlocked.
I called Metro PCS to replace my current phone (LG optimus 9) with the Note 2, they tried using the IMEI number and they told me that there was a problem, that they couldn't activate the phone, and that I had to go to a T-Mobile store. I went to the store, they checked the IMEI and they say it was fine, the guy also told me that the unlock codes are only valid for 72 hours and the person who sold me the phone requested the code on 01/17/14 which means the code its no longer valid.
After that I tried calling Metro to get the phone activated, it didn't work...
I thought that maybe the phone was still locked so I did a downgrade to 4.1.1 - UVALJ1 (the phone was rooted and it had a 4.3 custom rom) and unlocked the phone using the method of that "secret" menu. I tried using the Metro sim card, no luck. At this point I dont know what else to do, a T-Mobile sim card works fine, I haven't tried with another carrier, however I've been using my Metro sim card in my L9 with no problem, so I don't see why it shouldn't work with the Note 2.
So my question is if anybody has tried using the Note 2 on metro, specifically a T-Mobile one, and if so, how did you make it work?
I am pretty new to all of this rooting and android stuff, but I have done as much research as possible before asking, this is my last resource so hopefully someone can help me. Thank you in advance.
Update: After trying multiple times to activate the phone on Metro PCS it turns out the phone appears on their database as it hasnt been paid in full and theres an unpaid equipment installment balance, that is only on Metro PCS database. I went to T-Mobile and everything was fine on their system, no blacklisted, no unpaid balances, no nothing so I activated the phone with them. Now hopefully the guy who I bought the phone from doesnt decide to report the phone as stolen or lost just to be an ahole.
Im on android 4.1.1 and I want to upgrade but my phone its telling me that I cant upgrade because my phone was modified. I want to upgrade to 4.3 but I dont know if I lost root when I downgraded to 4.1.1, how can I check if im still rooted and what rom do you guys recommend flashing? Thanks in advance
-- Thread can be closed, already rooted, upgraded and de-bloated.

[Q] Device won't connect to any network

Hi, I have an SGH-I747M that was originally purchased through Bell. In an attempt to unlock to make it work on Koodo, I went through SamMobile (after reading there was no way to unlock post 4.3 OTA update) and that seemed to half work.They resell a service from 123unlock.nl which is a client that uses adb or something of the sort to mess with phone files. The program afterwards said "Your phone is now unlocked! However if you don't see any carriers you need to do something in the advanced option and pay another $2x.xx dollars to do so". I didn't feel like giving them any more money at this point because I was upset that what I originally paid for didn't work properly. The fix was apparently an option in the advanced options that was an NVM repair/rebuild or something of the sort. I should have screenshotted the issue but of course didn't.
Now, the phone will boot up and does not offer me a SIM unlock option anymore. When searching for carriers it will ever only find Rogers for some reason. It won't recognize Koodo or Telus or anything of the sort (or bell when my bell SIM is in). Every now and then when it boots up, it will successfully send a text but only within a 5-10 second time frame after boot (I've made 1 phone call as well for 3 seconds). I've tried the Koodo SIM in my own Nexus 5 and works fine so the network is okay at least (plus I called Koodo and they verified on their end things look good... if that makes a difference). The SGS3 won't even accept an original Bell SIM at this point. It's always on either no network, 1 bar or full bars, never anything in between. I've tried flashing different ROMs from Bell stock to Koodo stock and CM11 and it won't work no matter what I do. Under all ROMs it pops up an "ME Returned temporary error" message on the screen.
I'm hoping someone might have seen this issue before or know what's going on with the phone that I can fix. I'm assuming it's something to do with the modem part of the phone that's refusing to connect to carriers but I'm at a loss to fix it. I haven't tried flashing different modems on it yet because I'm unsure which one would be a good fix and no one has had roughly the same issue I could find in 3 days of Googling for this issue. Any ideas are greatly appreciated. Thanks.
sgtcanadian said:
Hi, I have an SGH-I747M that was originally purchased through Bell. In an attempt to unlock to make it work on Koodo, I went through SamMobile (after reading there was no way to unlock post 4.3 OTA update) and that seemed to half work.They resell a service from 123unlock.nl which is a client that uses adb or something of the sort to mess with phone files. The program afterwards said "Your phone is now unlocked! However if you don't see any carriers you need to do something in the advanced option and pay another $2x.xx dollars to do so". I didn't feel like giving them any more money at this point because I was upset that what I originally paid for didn't work properly. The fix was apparently an option in the advanced options that was an NVM repair/rebuild or something of the sort. I should have screenshotted the issue but of course didn't.
Now, the phone will boot up and does not offer me a SIM unlock option anymore. When searching for carriers it will ever only find Rogers for some reason. It won't recognize Koodo or Telus or anything of the sort (or bell when my bell SIM is in). Every now and then when it boots up, it will successfully send a text but only within a 5-10 second time frame after boot (I've made 1 phone call as well for 3 seconds). I've tried the Koodo SIM in my own Nexus 5 and works fine so the network is okay at least (plus I called Koodo and they verified on their end things look good... if that makes a difference). The SGS3 won't even accept an original Bell SIM at this point. It's always on either no network, 1 bar or full bars, never anything in between. I've tried flashing different ROMs from Bell stock to Koodo stock and CM11 and it won't work no matter what I do. Under all ROMs it pops up an "ME Returned temporary error" message on the screen.
I'm hoping someone might have seen this issue before or know what's going on with the phone that I can fix. I'm assuming it's something to do with the modem part of the phone that's refusing to connect to carriers but I'm at a loss to fix it. I haven't tried flashing different modems on it yet because I'm unsure which one would be a good fix and no one has had roughly the same issue I could find in 3 days of Googling for this issue. Any ideas are greatly appreciated. Thanks.
Click to expand...
Click to collapse
Can you check your phone's settings => About Device and let's know what parameters you have there (Android Version, Baseband Version, Build Number>.
You mentioned you can send text or make call within a limited time frame. Was that with the Koodo SIM or the Bell? If the former, it would suggest the phone is unlocked to some extent but you are probably experiencing a baseband failure or need to correct the APN settings. Did you also try doing a factory reset?
Larry2999 said:
Can you check your phone's settings => About Device and let's know what parameters you have there (Android Version, Baseband Version, Build Number>.
You mentioned you can send text or make call within a limited time frame. Was that with the Koodo SIM or the Bell? If the former, it would suggest the phone is unlocked to some extent but you are probably experiencing a baseband failure or need to correct the APN settings. Did you also try doing a factory reset?
Click to expand...
Click to collapse
The information you're asking for is attached.
The texts I got off were from the Koodo SIM. I have updated the APN as well, and I did do a flash back to stock resetting all settings through Kies emergency update. I found a little trick where if you softbrick it by trying to flash 4.1, it'll give you the "Please use kies" error and that'll take you back to full stock 4.3. I'm pretty sure the baseband failure is the option I need to explore but at this point I don't know where to go to fix this.
Edit: I read this online and tried it: "The 4.3 update introduces a "security feature" which requires carrier- or region-locked phones to be activated once on the original locked network before the unlock code will work." The phone didn't recognize any network with the Bell SIM in except "EXT" which I've never heard of before and it did not connect properly so that didn't work. I also read that inputting #7465625*638*# will give me the Samsung SIM unlock menu which it did however I don't think the issue here is with the root and I'd hate to pay $50 at this point to have that not work as well.
sgtcanadian said:
The information you're asking for is attached.
The texts I got off were from the Koodo SIM. I have updated the APN as well, and I did do a flash back to stock resetting all settings through Kies emergency update. I found a little trick where if you softbrick it by trying to flash 4.1, it'll give you the "Please use kies" error and that'll take you back to full stock 4.3. I'm pretty sure the baseband failure is the option I need to explore but at this point I don't know where to go to fix this.
Edit: I read this online and tried it: "The 4.3 update introduces a "security feature" which requires carrier- or region-locked phones to be activated once on the original locked network before the unlock code will work." The phone didn't recognize any network with the Bell SIM in except "EXT" which I've never heard of before and it did not connect properly so that didn't work. I also read that inputting #7465625*638*# will give me the Samsung SIM unlock menu which it did however I don't think the issue here is with the root and I'd hate to pay $50 at this point to have that not work as well.
Click to expand...
Click to collapse
It's unlikely to be the regional lock as this feature means your phone will work with compatible networks in the region but not in other regions. You may, however, run Chainfire's Region Lock Away to be sure <http://forum.xda-developers.com/showthread.php?t=2470551>
Your firmware settings look OK so I'd be doubtful about a corrupted modem. You may still try to re-flash the modem via custom recovery. Download link for the CWM flashable zip is available here ... http://www.androidfilehost.com/?fid=23252070760973552
The guys who sold you the original code seem to have sold a dud as there is no reason for them to be asking for secondary payments and this sounds like the footprint of a regular scam. I'd be surprised though as they seem to be well rated
Larry2999 said:
It's unlikely to be the regional lock as this feature means your phone will work with compatible networks in the region but not in other regions. You may, however, run Chainfire's Region Lock Away to be sure <http://forum.xda-developers.com/showthread.php?t=2470551>
Your firmware settings look OK so I'd be doubtful about a corrupted modem. You may still try to re-flash the modem via custom recovery. Download link for the CWM flashable zip is available here ... http://www.androidfilehost.com/?fid=23252070760973552
The guys who sold you the original code seem to have sold a dud as there is no reason for them to be asking for secondary payments and this sounds like the footprint of a regular scam. I'd be surprised though as they seem to be well rated
Click to expand...
Click to collapse
I've tried reflashing the modem and I've actually paid $50 for the unlock code from Bell, the original carrier. I used the code to get the network unlock menu and inserted the code. I still get between 1-4 bars now with no network access on either network. It's not showing anything except Rogers still in network operator selection.
Any ideas at this point? It refuses to connect to any networks. I'm out of options.
Edit: I don't know if this makes a difference, but when I do root explorer I can't actually find the nv_data.bin file. It doesn't have anything of the sort in the /efs folder.
sgtcanadian said:
I've tried reflashing the modem and I've actually paid $50 for the unlock code from Bell, the original carrier. I used the code to get the network unlock menu and inserted the code. I still get between 1-4 bars now with no network access on either network. It's not showing anything except Rogers still in network operator selection.
Any ideas at this point? It refuses to connect to any networks. I'm out of options.
Edit: I don't know if this makes a difference, but when I do root explorer I can't actually find the nv_data.bin file. It doesn't have anything of the sort in the /efs folder.
Click to expand...
Click to collapse
Please let me understand a few things ... when you first acquired the phone, was it working normally on Bell prior to the first unlock attempt or you never used it at all until you tried Koodo? Secondly, was the unlock code you got from Bell identical to the one you got from the online service?
I'm trying to establish if it is a case of hardware failure not reported by the previous user especially if you bought it pre-owned from the secondary market. If you are not sure of the previous usage history, it could be a faulty or disconnected antenna which may require professional service. On the other hand if you are sure it was working fine prior to the unlock attempt, try the following ...
1) From the dial pad, enter *#197328640#
2) [1] UMTS
3) [1] DEBUG SCREEN
4) [8] PHONE CONTROL
5) [6] NETWORK LOCK
6) [3] PERSO SHA256 OFF
7) Press Menu => Back button and go all the way back to Step 3) above
8) [6] COMMON
9) [6] NV REBUILD
10) [1] NV REBUILD
Reboot and restart and let's see if this does it.
I've got a similar symtom different scenario (sister in-laws phone). I was also only able to see Rogers network on a search. I've got Telus version. It was working fine until it was brought to the Philippines, got unlocked there and brought back to Canada.
I was only able to see Rogers network until I went into the Service Menu (similar to above) and found the option to change the band. I changed it to Automatic. After that I was able to see Telus network. When trying to connect/register it would take a long time and give me an error "Unable to connect, try again later". I still need to do more troubleshooting, but that might be something to look at.
Note: Phone has stock MOD ROM, rooted and unlocked.

[Q] Phone not allowed mm#6 error message

Phone: SHG-I317
Carrier: AT&T
Current Firmware: 4.1.1
Hey guys, I purchased this phone and have yet to officially activate it. I downgraded from 4.1.2 so that I could unlock it to work on other networks. I did the unlock procedure and I attempted to put in a METRO PCS Sim card but I get: Phone not allowed mm#6. The phone is not blacklisted as Ive checked numerous sites online and even went to a AT&T store and they were able to pop a AT&T Sim card in and it worked just fine.
I tried to search this issue but the only thing I can come up with was that it could possibly be blacklisted but Ive ruled out that possibility for now.
Could it be that the unlock was unsuccessful and I need to do it again? But then how am I supposed to know that it was successful without another carriers sim card? is there something that changes in the settings or something?
Thank you very much for your help.
http://forum.xda-developers.com/showpost.php?p=51349788&postcount=4

How to unlock LG-VS870 4G LTE by Verizon

Hello XDA community,
I have Verizon's LG-VS870 4G LTE smartphone [http://www.lg.com/us/cell-phones/lg-VS870-lucid2]. Now I'm in Canada and would like to use this phone instead of buying a new one, therefore I was told to unlock it. Apparently it's legal to unlock your phone now: http://lifehacker.com/you-can-now-legally-unlock-your-cellphone-heres-what-i-1614787933
So I searched online for how to unlock my LG phone. Found many results that tell me the first half of the steps. Found a couple of threads here too about it, but no concrete solution. Some people said this phone isn't going to work on GSM after you unlock it, but I found this patch thread here that says otherwise: http://forum.xda-developers.com/showthread.php?t=2394689
I have the original Verizon SIM card with me too.
Won't ya kindly help a bloke out and tell him how to get the unlock code for his LG-VS870?
So, I tried to root it and was successful with Framaroot. Then Installed Clockwork. Then attempted to install the above mentioned patch using Clockworks recovery mode, but it didn't appear to fix the GSM lock. Whenever I insert my SIM card I get an icon that looks like a SIM card with a question mark inside a red circle at the top right. And when I try to dial a number, any number, I get some chineese lady saying something.
Any idea what does that mean?
I just unbricked/unrooted my phone back to 711A firmware and 4.1.2 Android as it was all the way from the beginning.
Here's the vocaroo recording of the chinese lady(WARNING! TURN DOWN YOUR VOLUME FIRST!): vocaroo.com/i/s0C5ObqOLK6Y

Categories

Resources