[Q] Baseband -67 / -36 and custom ROM - Xperia Play Q&A, Help & Troubleshooting

Hello all, I'm new to this forum and i got some questions, (I did research, but I haven't find answer for my Q).
Ok so I got installed custom ROM on .58 FW, and I want change baseband from -67 to -36. I went thru tutorial http://forum.xda-developers.com/showthread.php?t=1469473 I did everything exactly how its says in step by step guide. The problem is when phone boots it keep giving me wellcome screen, poping up msg what I dont have enough space for my SMS, and when I go into phones internal storage its nothing there, I mean it does not show how many free space left and how many used.
So my question is: ROM is not supported by this baseband because this ROM is based under BB -67 ? Or I need to do something else ?
I want have this baseband because sometimes when I use data internet on my phone it respond very slowly.. i.e. I browsing internet everything OK, then I switch off screen and turn it back on, then go into browser and press any link there, my phone shows what is sending data but not receiving, after some while everything comes back and working fine again.. It very anoing thing, and I want fix that somehow.. I had this problem before I started to do any flashing (I was with stock FW) and now after some flashing new ROMs and kernels I still having..
Any suggestions ?
[My phone] r800i
[ROM] max_power 1.0v by sechko
[Kernel] Doomlord v10 [2Ghz]

No solution guys ?

You may want to try re-formatting (called a factory reset in CWR)
Get to your bootloader and the option should be there to delete the data/cache partitions.
Note - you should backup, nandroid, etc before doing this.

Thanks for the post, I will try as soon as I get home, hope this will help.
sent from Xplay r800i [ROM] GB 2.3.7 max_power v1.0 by sechko, Doomlord kernel v10.

Related

no service on gio

i flashed the CyanogenMod 9.0.0-RC0-GT-S5660-GalaxyICS-KANG-beta5, everything seemed to work fine, then i noticed that i wasn't getting any service at all. i then tried cyanogen 7.2 and same story. 7.2 is letting me make 911 calls unlike the ics rom.
can anyone help me pin the problem down and fix it? please and many thanks
i'm now in an endless boot cycle...
is there a guide to just to back to stock?
Flash stock rom via Odin if u want
@wiwid_colgate
Galaxy Gio S5660
#GalaxyICS
it was a supposed stock oden flash that caused me the never ending boot cycle
Odin does not reformat the /data and /cache partitions. Which would cause bootloops on a stock kernel that doesn't know how to handle ext4.
Use an RFS compatible recovery. Otherwise dd back empty RFS partitions back into place.
i had some problems with setting other launcher than adw on default. next time i'd restart the phone it got stucked at samsung logo. So i didn't set my favorite launcher on default and problems were solved. maybe it'll help.
For me the same prob. no service with CyanogenMod 9.0.0-RC0-GT-S5660-GalaxyICS-KANG-beta5 and cyanogen 7.2.
After that i flash with "S5660XXKTI - SER" (One Package-Android 2.3.6 Gingerbread stock)with odin and it runs like a train....(not like the dutch trains)
Do a full whipe before and after flashing.
coolhof said:
with odin and it runs like a train....(not like the dutch trains)
Click to expand...
Click to collapse
lol. that sentence has to be explained for people outside of the netherlands...
our train service is well known because of not driving trains when it freezes, a bit. like -10 degrees and ''wissels'' the things that make sure a train can move from railroad to another railroad, something like this..
we know much about water and dikes, but not about trainrail.
lol
misfit41 said:
i flashed the CyanogenMod 9.0.0-RC0-GT-S5660-GalaxyICS-KANG-beta5, everything seemed to work fine, then i noticed that i wasn't getting any service at all. i then tried cyanogen 7.2 and same story. 7.2 is letting me make 911 calls unlike the ics rom.
can anyone help me pin the problem down and fix it? please and many thanks
Click to expand...
Click to collapse
Wait.. you tested it by calling 911?
Sent from my GT-S5660 using xda premium
sim card problem
hey collholf , i have same problem with my gio, it say no service i have fully wiped and then flashed S5660XXKTI - SER" (One Package-Android 2.3.6 Gingerbread stock) after flashing i have wiped again , but i m still having same problem , plz help me out of this , my gio recognize the sim card for two hours or four hours then it says no service or no mobile network.
suhailaslam said:
hey collholf , i have same problem with my gio, it say no service i have fully wiped and then flashed S5660XXKTI - SER" (One Package-Android 2.3.6 Gingerbread stock) after flashing i have wiped again , but i m still having same problem , plz help me out of this , my gio recognize the sim card for two hours or four hours then it says no service or no mobile network.
Click to expand...
Click to collapse
You can try another stock firmware go back to 2.2.1 Froyo or 2.3.3. Gingerbread.
And don't forget to select Wipe data/factory reset before and after flashing.
Check if everything is working,if so than flash 3.3.6.
More i really don't no.
Maybe it has to do something about the "radio" you can found out by search here on xda.

[Q] Constant password prompt despite flashing/resetting

Hi Guys!
Well, basically..
the problem I have is just like in the title.
My SGW I8150 keeps constantly prompting "Enter password to unlock" (phone is on, at lock screen) despite numerous hard resets,(got CWM 6 recovery) formatting,clearing cache,dalvik etc.
it all started when i set up a short password for the lock screen.. (rom was stock, rooted and cwm 6, if not 2.3.5 then 2.3.6)
googled a lot, read a lot, no avail.
later flashed ics and had a week of struggle. mainly because of battery draining fast.
AND now, since I wanted to return to stock, because I do, the reason is the same. battery lasts the longest on that stock rom. I do a lot of texting calling music, pics and occasionally internet. 2 days battery lasted.
So i downloaded bagux-project-v1.4, rom had mostly everything i needed and installed it and still the same problem. Of course the initial setup settings always were present but after i completed them and the second the phone locks, the problem still persists..
rebelrom 3.0 as well shows the same..
only cyanogenmod rom's like "ancora beta3" or ics or any other rom which doesn't have the baseband / kernel (correct me) something in common shows this problem.
Also, no "forgot password" (e-mail help) does not pop up at all. only "emergency call".
I flashed other roms; Cm7 & arco68 CM9 and some other ics roms. THIS PROBLEM DOES NOT HAPPEN ON EITHER ICS version..
I have no idea why is this happening only on the roms generally similar to stock. 2.3.5 , 2.3.6 , 2.3.7
Please try to help if You can
baldusiek said:
Hi Guys!
Well, basically..
the problem I have is just like in the title.
My SGW I8150 keeps constantly prompting "Enter password to unlock" (phone is on, at lock screen) despite numerous hard resets,(got CWM 6 recovery) formatting,clearing cache,dalvik etc.
it all started when i set up a short password for the lock screen.. (rom was stock, rooted and cwm 6, if not 2.3.5 then 2.3.6)
googled a lot, read a lot, no avail.
later flashed ics and had a week of struggle. mainly because of battery draining fast.
AND now, since I wanted to return to stock, because I do, the reason is the same. battery lasts the longest on that stock rom. I do a lot of texting calling music, pics and occasionally internet. 2 days battery lasted.
So i downloaded bagux-project-v1.4, rom had mostly everything i needed and installed it and still the same problem. Of course the initial setup settings always were present but after i completed them and the second the phone locks, the problem still persists..
rebelrom 3.0 as well shows the same..
only cyanogenmod rom's like "ancora beta3" or ics or any other rom which doesn't have the baseband / kernel (correct me) something in common shows this problem.
Also, no "forgot password" (e-mail help) does not pop up at all. only "emergency call".
I flashed other roms; Cm7 & arco68 CM9 and some other ics roms. THIS PROBLEM DOES NOT HAPPEN ON EITHER ICS version..
I have no idea why is this happening only on the roms generally similar to stock. 2.3.5 , 2.3.6 , 2.3.7
Please try to help if You can
Click to expand...
Click to collapse
Try formatting the system cia CWM before flashing. See if that fixes your problem.
bbmadzky said:
Try formatting the system cia CWM before flashing. See if that fixes your problem.
Click to expand...
Click to collapse
bbmadzky, I did that numerous of times.
aotm, I'm back on CM9 ics 4.0.4 ancora. Best I can have for now..
baldusiek said:
bbmadzky, I did that numerous of times.
aotm, I'm back on CM9 ics 4.0.4 ancora. Best I can have for now..
Click to expand...
Click to collapse
how many times?lol..
anyways, how about formating system and everything....then......
download a firmware from sammy and flash it via odin..
or, you could follow this link:
http://forum.xda-developers.com/showthread.php?t=1467128
-salute!
reinjoy said:
how many times?lol..
anyways, how about formating system and everything....then......
download a firmware from sammy and flash it via odin..
or, you could follow this link:
http://forum.xda-developers.com/showthread.php?t=1467128
-salute!
Click to expand...
Click to collapse
a lot..
I said that before.. i did factory wipe/reset ,2nd option cache as well from cwm6 as well formatted the system, cache, dalvik, sdcard,onboard storage. one by one. did factory reset by using code *2767*3855#, still password prompt. downloaded a stock rom from sammy, flashed it via odin, still password prompt exists.
In my opinion, some data (specifically that unlock thing, password prompt) is left over on some piece of memory in the phone even though wiping, flashing and clearing has happened..
Hello... Please..Could anyone help me? Show me a way to do a FULL, but I mean seriously a COMPLETE WIPE of Data from each memory part on the motherboard.. Or at least something like that ?
Like I said, this happens only When the base of the rom is gingerbread..
Custom rom's/stock based on gingerbread when installed and the lock/power button is pressed and then again to turn the screen on, right away shows the password prompt...and that's where it all ends..
I had to install ICS, which is buggy and drains battery fast and since t's a whole new base to start from, the problem with password prompt disappears..
I don't know what to do anymore.. I'm not a noob at this because I have rooted MYSELF and flashed roms and other stuff to Samsung Gio Samsung Galaxy S II and Htc Desire-Z (a7272) and now I have my wonder I8150 and this weird thing just happened..

wifi do not turn on

Strange things happen to my i9195... suddenly out of the blue,wifi won't turn on neither from quick settings panel nor the settings itself...
Everything else works as it should(data,bluetooth,airplane,gps,sound etc) but the wifi setting tries to turn on but immediately turns of. anyone had this problem?
and more important... a solution??????????
Which rom are you on? You could try reflashing a rom to clear any possible software issues
yes try reflash rom
Whosat said:
Which rom are you on? You could try reflashing a rom to clear any possible software issues
Click to expand...
Click to collapse
citymen34 said:
yes try reflash rom
Click to expand...
Click to collapse
thanks guys for your replies...
i was on stock rooted xxuamf4, i flashed both xxuamh3 and xxuamg8 (these two i had already downloaded) but problem remained. just to eliminate software issue , as a last resort i flashed CM 10.1.3 and magically my device was fully functional again( by the way ..:good: to CM...).
So WTF? i 'll try later to flash a stock non rooted fw and see what will happen...
p.s : anyone know how to change baseband? in my sgs3 mini i used to flash different modem for that. what works for this device?
p.s 2 : thanks again for your time guys!:good:
flashing back stock firmware , problem reappeared! it seems something has to do with knox , because every time i try to open wifi a toasted notification appears "prevention information... the device as detected...bla...bla...bla"
the thing is that if i root my phone and completely delete knox,knox agent,store and container agent, the notification stops but the wifi setting still cannot be enable.
any ideas????
flashing back stock firmware , problem reappeared! it seems something has to do with knox , because every time i try to open wifi a toasted notification appears "prevention information... the device as detected...bla...bla...bla"
the thing is that if i root my phone and completely delete knox,knox agent,store and container agent, the notification stops but the wifi setting still cannot be enable.
any ideas????
Back to report that re-rooting with arco's method but with rootkit v2 (that includes kernel) seems to solve the issue! the steps i follow was :
1) gain root
2) install cwm recovery
3) with es explorer delete knox store,knox agent, container agent (both apk and odex files)
4) reboot to cwm recovery
5) clear cache and davlik cache
6) reboot and RESURRECTION!!!:good:
WiFi and Modem Issue
hi guys. i'm sorry for asking my question here,i have i9192 & my wifi do not turn on. i flash various version of official rom, but i cant solve this problem. I flash (MH2 ,MF7 ,MF9 and MJ2...) build number & CSC are change but Baseband version remain constant and don't change.
how can i flash modem( NON_HLOS.bin)...?
i root my phone so many time with Rootkit v2 and do all wipes for clean flash... but no successive achieve
how can i repair my WiFi and Bluetooth?
tighoory said:
hi guys. i'm sorry for asking my question here,i have i9192 & my wifi do not turn on. i flash various version of official rom, but i cant solve this problem. I flash (MH2 ,MF7 ,MF9 and MJ2...) build number & CSC are change but Baseband version remain constant and don't change.
how can i flash modem( NON_HLOS.bin)...?
i root my phone so many time with Rootkit v2 and do all wipes for clean flash... but no successive achieve
how can i repair my WiFi and Bluetooth?
Click to expand...
Click to collapse
i think it's a kernel related issue. But first in order to eliminated hardware problem possibility, try to flash a cm rom. If your wifi and bluetooth works then you can be sure it's not a hardware failure. in my case flashing a different kernel solved the issue.
p.s : if you find a way to change baseband version ,please share the way!!!
tighoory said:
hi guys. i'm sorry for asking my question here,i have i9192 & my wifi do not turn on. i flash various version of official rom, but i cant solve this problem. I flash (MH2 ,MF7 ,MF9 and MJ2...) build number & CSC are change but Baseband version remain constant and don't change.
how can i flash modem( NON_HLOS.bin)...?
i root my phone so many time with Rootkit v2 and do all wipes for clean flash... but no successive achieve
how can i repair my WiFi and Bluetooth?
Click to expand...
Click to collapse
you need flash same version Kernal file, example: when you finished flash MH2 stock firmware, if wifi shotdown, just flash MH2's Kernal file, file size around 7MB
hey hi
even i have the same error while turning on wi-fi prevention information blah blah
can you be brief how did you solved dat issue. it ll be very helpful
saiprasadap92 said:
hey hi
even i have the same error while turning on wi-fi prevention information blah blah
can you be brief how did you solved dat issue. it ll be very helpful
Click to expand...
Click to collapse
the solution for me was more or less "flashing rooted arco's kernel" . but my model is 9195. i honestly don't know if there is one for 9192 ,but if i were you i would search for one!
vriz27 said:
the solution for me was more or less "flashing rooted arco's kernel" . but my model is 9195. i honestly don't know if there is one for 9192 ,but if i were you i would search for one!
Click to expand...
Click to collapse
yeah thanks fa the reply . ill search for my phone and if you get the same for my phone do let me know
I have problem whith my s4 mini.. I9192 dual sim
Baseband : Nd1
When i want to connectt to wifi i enter password.. As soon as i hit the connectt button wifi signal will desappear... I updated the frameware but no sucsess...
How to solve?
Is it hardware issue?
Same problem for me (1st post): new i9195 with latest XXUCNK1, never flashed before,
install twrp and make a backup, install CM-12.1 and CM-13 without any issue,
After restore to KK using my twrp backup I can't turn on wifi,
solution was to flash Modem_I9195XXUCNK1.tar from modem thread.
I notice that twrp doesn't restore previous modem I update to XXUCOL1

[Q] Unknown problems there...

First of all, my English is not that good, so I hope everybody understand me
I'm a flashoholic (i think this is the right expression); i flash a new ROM almost every two weeks. And, from some days ago to now i'm experiencing some problems. Here's my problem:
Problem: my phone "stucks" when I let it locked for more than some 5, 10 seconds. I lock it now, and... dead. I have to press the power button until it restarts. My phone is having trouble to find operator's network and it's EXTREMELY lagged too. It almost stucks when i try to write something on the keyboard, or draw/write my passwords on my lockscreen.
Here's my "ROM timeline", too:
ROM Timeline: MIUIBrazil v4 [4.1.2] >> P.A.C MILESTONE [4.2.2] >> TigraROM/Hurricane [4.3 leaked] >> MIUIAndroid v4 [4.1.2] >> MIUIBrazil v4 [4.1.2]
Underline = i think that this is the point
Bold = problem started
So, let me explain my history: flashing ROM's as always, I decided to change things a bit and go AOSP for a while. So I flashed P.A.C. Milestone. Actually, I've flashed first the Nightly version, but it was a bit unstable. I went to P.A.C and everything went fine. But, hey, where are the Samsung functionality? I missed it. So, after some trouble finding the right ROM to me, the 4.3 from Samsung leaked. I tried it, then. First the Hurricane, afterwards the TigraROM (Note 3 functions ). And it was ok, but was lagging a lot. Too much launchscreen redraws to handle, so I went back to MIUI (not the first MIUI on the timeline, because I've decided to go right from scratch), and then, i've noticed a lot of problems.
It was not booting up.
I've flashed A LOT of ROM's trying to solve this problem. What it was? EFS folder. I went to the TWRP file manager on Recovery and noticed that the EFS folder was empty. And no backup. I went crazy until i found an old backup stored on my PC. Restored it right away, and everything was fine for a while... until it started doing some strange things like extreme lag and dead when locked.
And, when I went to recovery to look again to the EFS folder, it was always empty... i restored it again, again and after locked... BAM, disappeared. But some strange things are happening, like:
My bluetooth doesn't turn on.
My IMEI was fine, even with this EFS showing and hiding like that.
I'm almost finishing. Let me put here some basic questions that I know everyone will ask:
Q: have you tried to wipe everything and go from zero?
A: yep. It didn't worked.
Q: is your IMEI ok?
A: yep. But some things that are on the EFS folder doesn't wok, like Bluetooth. The MAC address of the bluetooth is there, but it doesn't show up when I write *#*#232337#*# on my Phone app (this code shows up Bluetooth address and try to turn it on... to me it tries to turn on forever).
Q: do you know that thing about the new modems? Click here to go to the post
A: yes, but only read it when i've had the problem. But i've restore that backup, and it was from the original ROM. So it doesn't seem to be this, because the backup was before this leak. Very very very before, actually.
I hope you guys can help me, and that I don't need to go to the Samsung support with the phone wiped. Thanks,
~imatheussm
When you say you've tried from zero, do you mean you've flashed a stock rom?
Sent from my GT-N7105 using xda app-developers app
3vo3d said:
When you say you've tried from zero, do you mean you've flashed a stock rom?
Click to expand...
Click to collapse
When I had this problem, the second/third thing I did was flashing the stock ROM. But it was with these problems too, and with some other weird things: the S Note and the Samsung Keyboard giving FC almost every second.
~imatheussm
Well I guess if you're getting these issues when completely on stock I reckon you need the service centre?
Sent from my GT-N7105 using xda app-developers app
Have you try formatting your internal sd? I got similar problem too when flashing 4.3 mj5 leak.
Also got a uid mismatch when the phone start. I format my internal sd then flashing 4.1.2 firmware back.
Not a problem after that.

[Q] Unlocked Galaxy Ace 2 + new ROM = lost unlock?

Hi everyone. I received my very first Android phone a couple of days ago, a Samsung Galaxy Ace 2. I did some research on the Android OS (my phone came with Gingerbread) and I found out about Cyanogenmod. So today, I installed C11 (found it right here http://forum.xda-developers.com/showthread.php?t=2568105) after a lot of sweat and blood... And I got it to run nicely, but I noticed I can't get my network to work. The phone was previously unlocked (I bought it used), and when I first tried my SIM on it, it worked.
When I first had to install CWM in order to be able to install the ROM, I succeeded in rooting it, and I noticed that the phone was still rooted after flashing it (though I don't know if that came along with C11). But anyway, I can't get my network to work; I removed the battery and the SIM a couple of times, but it didn't work. Now I don't know what to do. Could anyone please give me a hand on this? I know nothing about Android. Thanks in advance.
CM11 requires JB (4.1.2) - Sound like you flashed CM11 onto GB (2.3.6)
This can't work.
The thing is that I was trying to install an AOSP ROM (found in these forums as well) before trying with C11, and I wiped the data, formatted the system... So the phone was left without an OS. I didn't just "update" the OS, if you know what I mean. And C11 is working fine except for the mobile network.
EDIT: If I install a clean JB 4.1.2. and then restore to my current CM11, do you think that could solve the network issue?
Again: You need JB! With JB there are also other partitions which are needed to be new (on JB)
And Yes - Data restoring could work - But not recommended.... I would do an clean new install...
Please do not start an discussion... again: You needed JB.. (just to be sure)
Uhm, I never intended to start a discussion, I was trying to explain what I did. Thank you for replying anyway. I'll let you know if I get the network to work.
Sorry - I don't what to sound outrageous... But those questions were asked to many times... Here on XDA ACE 2 section...

Categories

Resources