Hi,
Could someone please explain to me how to get hold of frequencies below 700 MHz in the voltages tab of System Tune Pro? I want to set voltages but I cant find the settings for 51-700MHz frequencies...
Related
I found this in another site (originally written in Russian by user fibik @ se900.ru):
(http://translate.google.com/transla...//www.se900.ru/forum/index.php?showtopic=9180)
Acceleration
Status: [Enable] - status of overclocking is enabled or disabled
Load all modules: [Enable] - load modules for overclocking
Scaling: [Ondemand] - automatic CPU frequency scaling
Clk1: [300] - the frequency of the first stage of the frequency in MHz
Clk2: [600] - the frequency of the second stage of the frequency in MHz
Clk3: [800] - the frequency of the third stage of the frequency in MHz
Clk4: [1100] - the frequency of the fourth stage of the frequency in MHz, works only on official firmware firmware 2.3 and its modes
Vsel1: [20] - voltage at the first stage of frequency
Vsel2: [32] - voltage at the second stage of frequency
Vsel3: [42] - voltage at the third level of frequency
Vsel4: [65] - voltage at the fourth stage of the frequency
con_up_threshold: [80] - system load in% above which increases the CPU frequency? Bus?
con_down_threshold: [20] - system load in% above which lowers CPU speed? Bus?
con_freq_step: [5] - frequency step?
con_sampling_rate: [160 000] - interval (in milliseconds) between polls of the state of the system. In fact, the intervals between shifts the frequency of the processor? Times in 160 seconds?
int_min_sampling_rate: [50 000] - the minimum interval (in milliseconds) between polls of the state of the system. In fact, the intervals between shifts the frequency of the processor? Every 50 seconds?
ond_up_threshold: [86] - CPU in% above which increases the CPU frequency.
ond_sampling_rate: [50 000] - the second one? interval (in milliseconds) between polls of the state of the system. In fact, the intervals between shifts the frequency of the processor? Every 50 seconds?
smt_min_cpu_load: [40] - CPU in% above which decreases the frequency of the processor
smt_max_cpu_load: [85] - CPU in% above which increases the CPU frequency
smt_awake_min_freq: [30 000] - The minimum frequency of waking up?
smt_sleep_max_freq: [30 000] - CPU frequency during sleep?
smt_up_min_freq: [1200000] - How much to increase the frequency at a time?
smt_wakeup_freq: [1200000] - Frequency of waking up. It is important to not lose calls.
smt_ramp_up_step: [250 000] - on how to increase the frequency at a time?
[Set defalut (* req reboot / don 't save!!)] - Reset all settings to
[Save] - save the settings
con_ = conservative
ond_ = ondemand
int_ = interactive
smt_ = smartass (?)
That is, this is all profile names, one from which to choose.
sampling_rate - in Hertz likely, but not in milliseconds
awake_min_freq - the minimum frequency of not sleeping
Click to expand...
Click to collapse
Any volunteers confirm or even to play with the settings?
This could be useful to monitor the frequencies: https://market.android.com/details?id=com.bvalosek.cpuspy
very helpful ..Thx
i use setvsel at 32-300,42-600,52-1000 and its safe and no FC
Can any one suggest, to how to tweak other boot cpu setting other than clk and vsel.
Whitch option is the frequence on a call?
So Jamal ndtalled a Rom and the voltage is set to 1836. I set it to 1512 and reboot and it changes the max back to 1836. Please help I don't want to over clock my phone.
Sent from my SGH-T999
The voltage or the CPU clock frequency? If you are rooted just install System Tuner or Set CPU and you can set the clock speed.
Otherwise "Power Saving" mode brings the phone down to 900mhz I believe as well.
Not sure what's the difference I change the voltage a the cpu clock frequency is changed. I tried changing it in system tuner and I reboot and it's back up to the 1800's
Sent from my SGH-T999
I'm on Beanstalk asop ROM and the minimum frequency is 1026mhz causing a battery drain. is there a way to change it with no hassle?
this should help
http://forum.xda-developers.com/showthread.php?p=42394184#post42394184
You could try getting trickster mod app (free) donate if you like...then setting CPU min lower, don't forget to enable set on boot and apply
RubbleTea said:
You could try getting trickster mod app (free) donate if you like...then setting CPU min lower, don't forget to enable set on boot and apply
Click to expand...
Click to collapse
you also have to make sure the maximum is lower than 1024 otherwise itll just set the minimum to 1024. thats because of the kernel. the only other thing to do is change the kernel.
Im not very good at this CPU Clocking or know what the different "profiles" mean but im wondering what is the best type or profile to choose.
i have liquidsmooth flashed on my gnexus (gsm, verizon) the app i like to use is "FauxClock"
but im not sure what CPU Clock / HotPlug option to choose
i have it set on Max Clock - 1.20ghz
Min Clock - 350mhz
like whats the best clock level for best battery perfomance and then for best performance switching apps and other stuff ( ovbiously it will drain the battery but im willing to take the risk)
Hi Guys!!!
Please help me editing performance profiles..
Everytime i edit the
1. Power save
2. Balanced
3. Performance
profiles through performance setting above the developer options it gets reset to default. My settings dont save.
Presently im on CM11 RC20...
and i have read about the touch boost(the min and max frequency are same)
so everytime i set max and min value. The min value changes and goes equal to max value.
Can i change this behaviour. Because due to this the frequency getting stick to only max(which i set) and its not going down.
Please help me in editing(min and max values plus governor) these profiles to my choice and save them for permanent.
Thank you in advance.
Just tick the option of 'Set on Boot' and reboot.
Thank you for your reply...
I want to change all the profiles to my choice.
Like i want the below.
1. Balanced profile - from 300mhz to 998mhz governor- ondemand
2. Power Save profile - from 300mhz to 600mhz governor - powersave
3. Performance profile - from 300mhz to 1497mhz governor - ondemand
By setting on boot it is going to default. I want to manual edit them.