Related
Is bricking your device easy to happen? I'm scared of bricking my phone. Can the phone still brick when you do everything correctly?
Anything is possible.
I took chances on all my phones and never had a problem .
sent from the Dark §¡3€
MarsHD2 said:
Is bricking your device easy to happen? I'm scared of bricking my phone. Can the phone still brick when you do everything correctly?
Click to expand...
Click to collapse
If you do everything correctly, most likely not. A lot of bricks occurs because of user error. Flashing the wrong Galaxy s2 ROM/recovery etc, on our devices... there are a total of 5 variants i think.. only two works with ours.. skyrocket and hercules (i727 and t989)
I haven't heard of any bricks that occurs for doing everything correctly.
I have read up on some rare cases where a phone just blacks out from normal use... from heating up... or just random stuff.. some of the users aren't even rooted. That is purely the fault of the hardware simply giving up.
It is very easy to Root our phone:
ODIN
Flash Recovery
Flash ROM or Superuser
you can even mess up on flashing the recovery but you can actually recover from it. You will get the message where it says "firmware update failed, please connect to kies and recover," this is easily recoverable.. You just go back to ODIN Mode and flash recovery again.
The only way you can BRICK the phone:
1. Flash a ROM that doesn't belong to our device.
2. Mess up on Flashing a Stock ROM (user fault) such as battery falling out.. battery dying.. cable falls out. cable is loose etc.. while in the middle of flashing.
I remember reading that people tried to flash a Modem that didn't belong to our device, but ODIN either prevented this from happening or you get the "firmware update failed..." message.
TL;DR: No it is fairly safe and the only chances of bricking is when flashing something that isn't for our phone.
1. Flash a ROM that doesn't belong to our device.
2. Mess up on Flashing a Stock ROM (user fault) such as battery falling out.. battery dying.. cable falls out. cable is loose etc.. while in the middle of flashing.
Click to expand...
Click to collapse
I still don't see how those two things can mess up the phone? Can't you just use odin to reflash? You would think that they make the download portion of the phone non-writable so you can always use it with odin to reflash in any state. I must be missing something here. Does flashing a ROM mess with the "Download" partition also?
It is normally unwritable to prevent such problems. By using odin, you are bypassing the safety feature of the ROM area. By interrupting the process mid-way, you might not do not copy over all the 'necessary' files for the phone to function at it's lowest levels of operation. IE turn on when you tell it to. Flashing a rom doesn't mess with the user accessible partition.
Is using ClockWorkMod to flash any safer?
Catch-22.
If you want to use the ClockWorkMod app to flash, you will need to grant it superuser permissions. How do you get superuser? You need to be rooted by installing ClockWorkMod.. odin is pretty safe. Make sure to have a half-way charged battery (at least), and click the pda button.
True but how about subsequent flashes
Look bro its hard to brick these samsung but its not impossible trust me i know from experience, my first ever phone i rooted and played with was the galaxy s 4g and lets just say i bricked the **** out of it. think of it like this you flash a rom for a phone that is not yours this phone has a physical keyboard and the only way that phone can get into download mode is a combination of keys on the keyboard (this is just hypothetical) and the only way to get odin to recognize device is to be in DL mode...How can you be in DL with a phone that doesnt have physical keyboard but requires use of it to get into DL mode.
I've never bricked. Been in a bootloop, but just had to wipe and flash again
Sent from my SGH-T989 using xda premium
jdubb1106 said:
Look bro its hard to brick these samsung but its not impossible trust me i know from experience, my first ever phone i rooted and played with was the galaxy s 4g and lets just say i bricked the **** out of it. think of it like this you flash a rom for a phone that is not yours this phone has a physical keyboard and the only way that phone can get into download mode is a combination of keys on the keyboard (this is just hypothetical) and the only way to get odin to recognize device is to be in DL mode...How can you be in DL with a phone that doesnt have physical keyboard but requires use of it to get into DL mode.
Click to expand...
Click to collapse
Get a jig?
Sent from my SGH-T989 using XDA App
jig didnt work on my sgs4g. And all that example was purely hypothetical, just using as example so op understands what people are trying to say.
Sent from my SGH-T989 using xda premium
jordanishere said:
Get a jig?
Sent from my SGH-T989 using XDA App
Click to expand...
Click to collapse
I tried to flash a kernel and a rom for the i9100 on mine using cwm. Flash went through just fine, went to reboot.... Nuthin. Not even a jig brought it back. Just be sure of what you're flashing and you'll be good. I've been flashing roms since the razr v3, and this is my first brick.
Sent from my Nexus One using Tapatalk
zak rabbit said:
I tried to flash a kernel and a rom for the i9100 on mine using cwm. Flash went through just fine, went to reboot.... Nuthin. Not even a jig brought it back. Just be sure of what you're flashing and you'll be good. I've been flashing roms since the razr v3, and this is my first brick.
Sent from my Nexus One using Tapatalk
Click to expand...
Click to collapse
Its tough with all the diff varients. doesnt help that they all have the exact same name too.
Props for not being one of the whiners who blames their brick on xda. hope you get a new t989.
Sent from my SGH-T989 using XDA App
Just to throw this in there - if your phone does ANYTHING when you try to turn it on (soft keys light up/some sort of response from the screen), or plug it in, it is a soft brick in which you should be able to recover the phone. Many times it takes multiple tries (due to picky button combos) but it will come back. Coming from the Vibrant 3g, I can tell you from experience that you know when you have a hard brick because the phone does not respond AT ALL. It doesn't do anything when it's plugged in or when buttons are pressed. The ONLY time I've legitimately bricked a sgs was when I flashed a rom on a low battery not knowing that the phone does not charge in recovery. The battery died during reboot and the phone would not respond to anything. This is a true hard brick.
Also i'm not sure if this has been said but I would never flash anything without art least 50% battery life
The galaxy is pretty cool because of how easy it is to unbrick. All you have to do it load the stock kernel from Odin and plug up the USB, mount the sd, and place the ROM onto the sd and unmount then flash it. In the case that you install a bad ROM, if it's just the kernel then just load the stock kernel with Odin then use the one you want.
Sent from my SGH-T989 using xda premium
iwasblown said:
The galaxy is pretty cool because of how easy it is to unbrick. All you have to do it load the stock kernel from Odin and plug up the USB, mount the sd, and place the ROM onto the sd and unmount then flash it. In the case that you install a bad ROM, if it's just the kernel then just load the stock kernel with Odin then use the one you want.
Sent from my SGH-T989 using xda premium
Click to expand...
Click to collapse
that was very confusing, but I'm not sure if you really know what a true hard brick is, which is really hard to unbrick and need to do the jtag stuff.
what you addressed is a softbrick (i don't even consider this a brick because the phone turns on), which is flashing an incomplete rom or kernel that is for our device, however if it was another device's than it might lead to a hardbrick.
Teo032 said:
that was very confusing, but I'm not sure if you really know what a true hard brick is, which is really hard to unbrick and need to do the jtag stuff.
Click to expand...
Click to collapse
A true hard brick cannot be unbricked. With a true hard brick the phone won't turn on and therefore, you cannot use Odin. Jtag also won't work if the phone does not turn on/the hardware buttons don't work.
Hello,
Recently I've flashed Arco's CM9 version. It all went well for a couple of weeks until today. When I booted my phone, suddenly all apps started crashing and then it rebooted. But, the problem is, it is now stuck on a flashing Samsung logo.
Before I've started this thread, I've read many many similar threads about this, and started a 'rescue operation' by my own by using the tutorials for flashing back a stock rom with ODIN and other possibilities.
Unfortunately, after I've tried twice using ODIN, my phone is still stuck in the Samsung logo loop. I also can't enter Recovery mode, but am able to enter Download mode, as you've probably noticed.
As this is my first Android phone, I've always carefully read the tutorials and disclaimers about possible failures. I'm aware that the maker of the rom is not responsible for this.
Since I tried to flash back to stock android 2.3.6 from CM9 kernel, I've read that this could give some problems. My question is:
- Would flashing CM9 back worth a shot, or totally useless?
I hope you can help me, and if there isn't a solution, I hope the shop can cover this as I've got warranty for one year and 9 months.
Care to share how you had flashed it at first...
And you can still boot to recovery rite ?
Sent from my GT-I8150 using xda premium
countdown93 said:
Hello,
Recently I've flashed Arco's CM9 version. It all went well for a couple of weeks until today. When I booted my phone, suddenly all apps started crashing and then it rebooted. But, the problem is, it is now stuck on a flashing Samsung logo.
Before I've started this thread, I've read many many similar threads about this, and started a 'rescue operation' by my own by using the tutorials for flashing back a stock rom with ODIN and other possibilities.
Unfortunately, after I've tried twice using ODIN, my phone is still stuck in the Samsung logo loop. I also can't enter Recovery mode, but am able to enter Download mode, as you've probably noticed.
As this is my first Android phone, I've always carefully read the tutorials and disclaimers about possible failures. I'm aware that the maker of the rom is not responsible for this.
Since I tried to flash back to stock android 2.3.6 from CM9 kernel, I've read that this could give some problems. My question is:
- Would flashing CM9 back worth a shot, or totally useless?
I hope you can help me, and if there isn't a solution, I hope the shop can cover this as I've got warranty for one year and 9 months.
Click to expand...
Click to collapse
it happened to my friends phone also, he can go to DL mode but not recovery mode, he flashed a stock rom via odin, but that didnt help, he was still stuck at samsung logo, and about flashing CM9 again, i guess u cant bcoz u cant go to recovery mode, if youve flashed a stock rom again and that didnt work for you too, i guess u need to send to samsung for repair, i remember my friend said it was a hardware problem, good luck
vanir29 said:
it happened to my friends phone also, he can go to DL mode but not recovery mode, he flashed a stock rom via odin, but that didnt help, he was still stuck at samsung logo, and about flashing CM9 again, i guess u cant bcoz u cant go to recovery mode, if youve flashed a stock rom again and that didnt work for you too, i guess u need to send to samsung for repair, i remember my friend said it was a hardware problem, good luck
Click to expand...
Click to collapse
I've read elsewhere that it was a hardware problem that appeared on 1:10 Wonders... I'm really disappointed since this was my first smartphone...
A small question though: Since I've (tried to) flash it back to stock rom, if I bring it back to the shop where I bought it, would they notice that there was another rom, which could give them a reason that I've void the warranty? I really don't want to pay another amount of cash for this (faulty) phone.
Also in reply to andynroid: I've flashed CM9 the first time with CWM, as adviced by Arco68.
Can you still go to recovery ?
Sent from my GT-I8150 using xda premium
countdown93 said:
I've read elsewhere that it was a hardware problem that appeared on 1:10 Wonders... I'm really disappointed since this was my first smartphone...
A small question though: Since I've (tried to) flash it back to stock rom, if I bring it back to the shop where I bought it, would they notice that there was another rom, which could give them a reason that I've void the warranty? I really don't want to pay another amount of cash for this (faulty) phone.
Also in reply to andynroid: I've flashed CM9 the first time with CWM, as adviced by Arco68.
Click to expand...
Click to collapse
well in my friend's case, samsung accept it and repair it, if the stock rom is flash successfully, i think they wont notice that you've flash i custom rom, good luck though
Am I being dense.... but what is 1:10 Wonder???
I saw this also mentioned by Rio S. (I think)....but did not think anything about it.... but, is it HW version??
Where can I see it on device.
Andy....
Guy says in OP...
can't get Recovery!!!
:banghead:
Sent from my GT-I8150 using Tapatalk
irishpancake said:
Am I being dense.... but what us 1:10 Wonder???
I saw this also mentioned by Rio S. (I think)....but did not think anything about it.... but, is it HW version??
Where can I see it on device.
Andy....
Guy says in OP...
can't get Recovery!!!
:banghead:
Sent from my GT-I8150 using Tapatalk
Click to expand...
Click to collapse
Hi...
I wrote in this thread
http://forum.xda-developers.com/showpost.php?p=25616419&postcount=17
The only solution seems to be to flash an Asian rom with multi package.
Sent from my GT-I8150 using Tapatalk
when you try to enter recovery mode, what is the image you first see? is there an image that look like an android? i cant remember the exactly image but if you see that image, i think you must reflash the CWM via odin. Because every time i reflash the stock rom, my recovery mode will gone. So try to reflash CWM via odin. Nothing wrong if you give it a try
irishpancake said:
Am I being dense.... but what is 1:10 Wonder???
Click to expand...
Click to collapse
i think it is one(1) out of ten(10) or 1 is to 10 sgw has a hardware problem, i guess thats what he meant, but isnt it kinda high
Experienced this as well. Just sent it for warranty and they swapped out the motherboard.
alidsd said:
The only solution seems to be to flash an Asian rom with multi package.
Sent from my GT-I8150 using Tapatalk
Click to expand...
Click to collapse
I've heard and read about that, I thought that Rio did that, but it wasn't succesful.
tomatoman23 said:
when you try to enter recovery mode, what is the image you first see? is there an image that look like an android? i cant remember the exactly image but if you see that image, i think you must reflash the CWM via odin. Because every time i reflash the stock rom, my recovery mode will gone. So try to reflash CWM via odin. Nothing wrong if you give it a try
Click to expand...
Click to collapse
I wished I could enter Recovery mode, but the problem is: I can't
. But I also didn't know that if I flash back to stock rom, the recovery would be gone too. Maybe I should reflash CWM via odin. Nice advice.
vanir29 said:
i think it is one(1) out of ten(10) or 1 is to 10 sgw has a hardware problem, i guess thats what he meant, but isnt it kinda high
Click to expand...
Click to collapse
Jup. One out of ten => 10%. Such an error rate may not appear for such a great brand. That is ridiculously high. Even 1% is too high in my opinion.
Deathmax said:
Experienced this as well. Just sent it for warranty and they swapped out the motherboard.
Click to expand...
Click to collapse
Yeah, but what I've heard from others in the Netherlands: they will say that your device has been damaged by water, which isn't protected by warranty. And the bill is equal to a new device, or even more expensive. I hope they're in 'good mood', otherwise I maybe have to search for another device.
Hey Bro... this happen to me a while ago.... but covered by warranty , just simply told them at the SSC that you do an update via Kies and sxxt happen , coz in my place there are cases that the phone hang after update via Kies not only this model , it happen to others model too.
I suggest that you flash it back to stock before you send it back to SSC , without CWM .
cheers
vanir29 said:
i think it is one(1) out of ten(10) or 1 is to 10 sgw has a hardware problem, i guess thats what he meant, but isnt it kinda high
Click to expand...
Click to collapse
My friend!!!
I think you have solved the mystery of 1:10......
but can Rio S. confirm??
I don't have bricked phone....
but I try to understand what is causing these, so to be of some help....
and 1:10 was a puzzle to me, so thank you...
Sent from my GT-I8150 using Tapatalk
My Phone all of a sudden restarted and now has a black screen and keeps vibrating. my battery isnt dead and it will boot into the ROM I have flashed for a brief second then reboot itself back into the black screen. It won't even boot into recovery nor will it boot into download mode. PLEASE HELP!!!
Fly2Deaf said:
My Phone all of a sudden restarted and now has a black screen and keeps vibrating. my battery isnt dead and it will boot into the ROM I have flashed for a brief second then reboot itself back into the black screen. It won't even boot into recovery nor will it boot into download mode. PLEASE HELP!!!
Click to expand...
Click to collapse
So what exactly happened?
Sent from my SGH-T989 using xda premium
Sounds strange. What exactly did you flash before hand? From/kernel/mods anything.
Sent from my SGH-T989 using xda premium
Odin you noob. Why do you even waste time with posting such useless garbage? If you can't get back to stock from Odin then post.
I handed my phone to my mother to show her a picture and when she went to hand it to my aunt, my aunt dropped it. I didnt think nothing of it when I locked the screen but when I went to unlock it, my phone restarted and went to a straight black screen and started to vibrate over and over again. I tried to pull the battery and then re-insert it and boot into recovery but when recovery showed up and I went to restore to a previous ROM the phone rebooted itself and started vibrating again. Now I'm at the computer trying to place it into Download Mode. The screen pops up that says to either push Vol + for Download or Vol- for restart. When I press Vol+, the phone restarts and goes straight to a black screen again.
And I'm not a noob, I know what I'm doing my phone just started acting up
And I'm Running the AOKP ROM with Eugene's ICS Kernel with the Tmo_SGH-T989_LC8_Radio
What previous from were you trying to restore?? When you restore a nand back up you have to make sure that the rom you're restoring is the rom that's already installed. In other words if you wanted to restore a back up you would have needed to flash the correct rom before hand. Though I'm confused because if you did try and restore a previous rom say a cm9 back up and you have aokp currently installed it shouldn't work. Cwm will tell you there's a mismatch and it aborts the installation. My guess is this drop did some damage. Your phone isn't making it past post per say of your using pc terms. Can you try and boot back into cwm? You said download mode doesn't work. But does cwm?
kr3w1337 said:
Odin you noob. Why do you even waste time with posting such useless garbage? If you can't get back to stock from Odin then post.
Click to expand...
Click to collapse
He mentioned he can't boot into download mode. You didn't even bother to read the whole post before jumping the gun and insulting the guy. You are what's wrong with these forums. Idiot.
Sent from my SGH-T989 using xda premium
I couldn't even get into cwm at all. But now i was able to get into Download Mode to flash back to Stock ICS using Oden and now Oden won't flash The ICS ROM back to my phone for some reason. Oden does recognize my phone but it won't flash anything
I would buy a USB jig they're cheap on eBay it'll force into download mode so u can restore in odin
Sent from my SGH-T989 using xda premium
I don't know what I did but thankfully I got it to boot into CWM and I'm restoring my ROM
maybe hardware problems if you dropped it, wasn't bricked, we usually say bricking a phone from bad flash, don't we? lol, i am not sure. try taking off sim card, micro sd card and battery then carefully put them back on next time if you have problems from drops etc........
Got to admit the whole "Brick" wording gets thrown around way too much for my liking and lets be honest if you are not a noob then you know all the steps to take in my opinion to try and restore your phone. If those steps dont work and you have researched the web then let Insurance kick in if you have it.
Not trying to flame or be an ass but just saying any non noob should know the steps to try and bring our phone back from the dead... I dont think starting a "Brick" thread should be on that list... Coming from the epic touch where the ICS kernel was bricking everyone its just makes me cringe when I see that word.... My bad man if you don't care for my opinion
IJS
Have the exact same problem, can't get it into recovery or download mode.
Sent from my SGH-T989 using xda app-developers app
RushAOZ said:
He mentioned he can't boot into download mode. You didn't even bother to read the whole post before jumping the gun and insulting the guy. You are what's wrong with these forums. Idiot.
Sent from my SGH-T989 using xda premium
Click to expand...
Click to collapse
He got as far as ROM so I knew for a fact that he could get to download and/or recovery. Just like he in fact did.
Idiot. Learn more about the phone you hold.
Sent from my SGH-I727
Play nice. It's fun to read about people's phone situations.
Sent from my SGH-T999 using xda premium
Here is my 2 cents
Yes people jump the gun and post bricked phone threads but that's probably because they are panicking.. And yes I agree that people should use the search function and read whenever possible.. And yes people should be reminded to do so..
But if you have the time to criticize someone then why don't you try to help them too..
If you have nothing helpful to add then don't post anything
I like my Roms the way I like my women..... Clean and smooth
I had this same problem,when I tried to go in to recovery and do a restore it would reboot its self even while flashing a Rom.what I did was...go in to recovery and quickly clear cache before it reboot then go back and clear dalvik then go back and try to flash the same Rom you had installed. It did work for mange when I was trying to restore.
Hope this helps
Sent from my SGH-T989 using Tapatalk 2
RushAOZ said:
Sounds strange. What exactly did you flash before hand? From/kernel/mods anything.
Sent from my SGH-T989 using xda premium
Click to expand...
Click to collapse
Honestly, your the type of person everyone hates on xda.
Sent from my SAMSUNG-SGH-T989 using xda premium
so you tried..
1. remove battery.
2. plug in phone to usb on computer with battery STILL OUT
3. while plugged in hold down volume up and down.
4. Still plugged in and still holding the volume up and down, insert your battery.
5. boom choose continue and find download mode.
If this doesn't get you to DL mode then either something broke hardware wise when you dropped it, OR your not being honest with what you did to cause the problem..
my att s3 stuck on a black screen, I don't even know if it turns on or not. It was rooted, mistakenly trying to install Criskelo 5.4.2 from internal sd card, it said aborted, then I tried to reboot, but it never came back on. please help
Isn't that a I9300 rom...?
Sent from my SAMSUNG-SGH-I747 using xda premium
http://forum.xda-developers.com/showthread.php?t=1727443
Try that thread, but there's a good chance you hard-brickedit. Like a paperweight.
defnow said:
Isn't that a I9300 rom...?
Sent from my SAMSUNG-SGH-I747 using xda premium
Click to expand...
Click to collapse
Yes, that is a I9300 rom, while I have a SGH-I474. I know, I made a mistake.
NewAndro1d said:
Yes, that is a I9300 rom, while I have a SGH-I474. I know, I made a mistake.
Click to expand...
Click to collapse
That sucks man . Use the thread provided above. If that doesn't work ...you've hardbricked.
Sent from my SAMSUNG-SGH-I747 using xda premium
I can't even bring the phone to download mode. Already tried pressing all the combination keys, it's still won't power up. I'm ordering a USB Jig to try to get it to download mode. At this point, it is hard bricked.
Go through the motions of getting into dl mode. See if Odin recognizes it, even though the screen is black.
I tried the motion, it's a hardbrick, gonna send it in to mobiletechvideos to see if they can fix it.
NewAndro1d said:
my att s3 stuck on a black screen, I don't even know if it turns on or not. It was rooted, mistakenly trying to install Criskelo 5.4.2 from internal sd card, it said aborted, then I tried to reboot, but it never came back on. please help
Click to expand...
Click to collapse
sorry to hear that dude...i have same problem as you....end up send to samsung to get new one.....lesson learn READ OVER AND OVER make sure it compatible to your phone version....
Update: I had to send my phone to MobileTechVideos, cost $60, and he fixed it. Wow, I got my phone back yesterday and it works. I'm afraid to root and flash my phone now.
NewAndro1d said:
Update: I had to send my phone to MobileTechVideos, cost $60, and he fixed it. Wow, I got my phone back yesterday and it works. I'm afraid to root and flash my phone now.
Click to expand...
Click to collapse
Don't be afraid just make sure you flash the right ROMs.stick to original development forums and you'll be good
Sent from my SGH-I747 using xda premium
NewAndro1d said:
Update: I had to send my phone to MobileTechVideos, cost $60, and he fixed it. Wow, I got my phone back yesterday and it works. I'm afraid to root and flash my phone now.
Click to expand...
Click to collapse
It's your choice whether you want to root your phone or not but I suggest just taking the time to read everything what form what section of the form what carrier what are the bugs what are the risks. I have been rooting phones for about two years now and I have never booked a device because I read that I read again and then I use the search function.
NewAndro1d said:
my att s3 stuck on a black screen, I don't even know if it turns on or not. It was rooted, mistakenly trying to install Criskelo 5.4.2 from internal sd card, it said aborted, then I tried to reboot, but it never came back on. please help
Click to expand...
Click to collapse
I have the same problem now did you try usb jig ???
anti459 said:
I have the same problem now did you try usb jig ???
Click to expand...
Click to collapse
This is almost as frustrating in the one xl forums with people flashing tegra roms .. try a jig they're cheap if not I'm sure you'll have to send it to mobiletechvideos.com
it seems that my friend has bricked his phone by installing a verizon boot loader in a at&t gs3 i tried going into recovery and download but nothing the phone wont boot or anything seems to be dead.
question is is there any way to fix it I tried many methods but all failed ):
Why would he install a verizon bootloader? He might have to get a jtag service to fix it. Bummer
Sent from my SGH-I747M using xda premium
undecided323 said:
it seems that my friend has bricked his phone by installing a verizon boot loader in a at&t gs3 i tried going into recovery and download but nothing the phone wont boot or anything seems to be dead.
question is is there any way to fix it I tried many methods but all failed ):
Click to expand...
Click to collapse
Jtag once i was having same issue with my brothers phone tried tiresly but no go
Sent from my SGH-I747M using xda premium
1) Charge battery & phone for an hour.
2) Pull battery for five minutes
3) Put battery back in
4) Press and hold VolumeDown+Power+Home
If that doesn't get you ANY display at all, not even a splash screen, then it's a "hard brick" and he'll need to send his phone out for "JTAG" repair. They are available on eBay for ~$50.
If you do get display, then come back and let us know for the next step (odin).
Some people think the phone is bootloader Locked. When they see that verizon version has bootloader unlock, they flash that.
I almost made that mistake, but I read and re-read everything for a week before even downloading stuff to try
Sent from my SGH-I747M using xda app-developers app
Is it possible for a usb jig to fix my problem?
undecided323 said:
Is it possible for a usb jig to fix my problem?
Click to expand...
Click to collapse
HIGHLY doubtful at the moment. Have you tried the above listed options?
Deoxlar said:
Some people think the phone is bootloader Locked. When they see that verizon version has bootloader unlock, they flash that.
I almost made that mistake, but I read and re-read everything for a week before even downloading stuff to try
Sent from my SGH-I747M using xda app-developers app
Click to expand...
Click to collapse
Deoxlea...... WHAT.... HOW DARE YOU..... You mean you READ stickies? What are you trying to do. Set a good example?
My only option for the phone to start working is a jtag or a usb jig. I I ordered a usb jig and will report back if it fixes my phone
I have a jig from my old captivate that has worked both times I've tried to get into download.