GSM Galaxy Nexus with AT&T - Samsung Galaxy Nexus

So I recently received my nexus, and set it up with cm10 nightlies, but i seem to never have a data connection. I've looked online for apns and have tried every one but I always get connection for a few minutes, but then disconnects. This happens periodically throughout the day. And I know its not where I live because I was getting a great connection on my skyrocket. So I guess my question is what apn's are you guys using for att? Or maybe do you think I have a broken phone that needs to be sent back. I really wanna keep this phone, but the constant data disconnects are frustrating me! I hope this makes some sense, lol. Anyways, thanks!

jororosco said:
So I recently received my nexus, and set it up with cm10 nightlies, but i seem to never have a data connection. I've looked online for apns and have tried every one but I always get connection for a few minutes, but then disconnects. This happens periodically throughout the day. And I know its not where I live because I was getting a great connection on my skyrocket. So I guess my question is what apn's are you guys using for att? Or maybe do you think I have a broken phone that needs to be sent back. I really wanna keep this phone, but the constant data disconnects are frustrating me! I hope this makes some sense, lol. Anyways, thanks!
Click to expand...
Click to collapse
Once you installed CM10, were the APNs intact or was the list empty?
I've just looked at my GN, also on AT&T, and found the following:
NAME: ATT
APN: wap.cingular
Proxy: <Not set>
Port: <Not set>
Username: [email protected]
Password: <Not set>
Server: <Not set>
MMSC: http://mmsc.cingular.com
MMS proxy: wireless.cingular.com
MMS port: 80
MCC: 310
MNC: 410
Authentication type: <Not set>
APN type: default,supl,mms
APN protocol: IPv4
APN enable/disable: (checked off, but is grayed out and says 'APN enabled')
Bearer: unspecified
I think these APN settings are pretty standard. They were put into place by CM10 and I haven't touched them. Coincidentally, I was just about to flash back to stock; if you'd like, I'll double-check these settings once I've done so.
Good luck.

Did you test the phone before flashing nightly roms? maybe try pushing it back to stock and see if that is the issue

So yes I was on stock and I was having the same issues. That's why I flashed cm10 to see if it would help. I have the exact same apns as you do. And when it connects I'll have 5 bars. And literally within a minute, I see it drop all the way down to no bars and then it disconnects from the network. Thanks for the replies. I'm starting to think that I should exchange it for another one to see if its just the phone.
Sent from my Galaxy Nexus using xda app-developers app

It is my understanding that the GS2 Skyrocket being an LTE device your account and is provisioned for the pta APN.
I am in the middle of something right now, but tomorrow I will post the pta APN info.
Dan

http://forum.xda-developers.com/showthread.php?t=1684711

Related

Telus Desire on Rogers won't connect to 3G no matter what

I've got a Telus HTC Desire unlocked and being used on Rogers. It's rooted and flashed with the proper radio for Froyo (32.43.00.32U_5.09.00.20) and running Cyanogenmod 6.0.0 RC2.
It makes phonecalls and texts just fine, but I cannot for the life of me get 3G working on Rogers. Wifi works fine too, but 3G is just a total no-go.
I've got the APN set up correctly as far as I can tell, and in the settings data is turned on.
Any ideas?
try these settings
Name: Rogers
APN: rogers-core-appl1.apn
Proxy: <Not set>
Port: <Not set>
Username: <Not set>
Password: <Not set>
Server: <Not set>
MMSC http://mms.gprs.rogers.com
MMS proxy: 10.128.1.69
MMS port: 80
MCC: 302
MNC: 720
APN type: <Not set>
the_ahmadzais said:
try these settings
Name: Rogers
APN: rogers-core-appl1.apn
Proxy: <Not set>
Port: <Not set>
Username: <Not set>
Password: <Not set>
Server: <Not set>
MMSC (can't have this url here due to XDA-Dev new account restrictions, hah
MMS proxy: 10.128.1.69
MMS port: 80
MCC: 302
MNC: 720
APN type: <Not set>
Click to expand...
Click to collapse
You are the king of kings, sir. Thank you so much, problem solved.
Np man . Enjoy ur beautiful desire
vertigo360 said:
I've got a Telus HTC Desire unlocked and being used on Rogers. It's rooted and flashed with the proper radio for Froyo (32.43.00.32U_5.09.00.20) and running Cyanogenmod 6.0.0 RC2.
It makes phonecalls and texts just fine, but I cannot for the life of me get 3G working on Rogers. Wifi works fine too, but 3G is just a total no-go.
I've got the APN set up correctly as far as I can tell, and in the settings data is turned on.
Any ideas?
Click to expand...
Click to collapse
Hi
I am just wondering ... you started with a Desire from telus A8181 and rooted and flashed so you can use it with rogers and have 3G?
I am going to do the same I just want to make sure it will work with rogers 3G and could you also share how do you flash your phone please?
Thank you !!!
The Telus version is A8182
niniderm said:
Hi
I am just wondering ... you started with a Desire from telus A8181 and rooted and flashed so you can use it with rogers and have 3G?
I am going to do the same I just want to make sure it will work with rogers 3G and could you also share how do you flash your phone please?
Thank you !!!
Click to expand...
Click to collapse
Telus and Bell's 3G network share the same frequency spectrum as Rogers. So yes, they should work, provided the phone is setup correct. Thats why all of Canada's big 3 can offer the iPhone.
I signed up just to thank you! Even the Rogers tech support didn't know what to do. Simple when you know, and my HTC Desire has zero APNs available. Soon as I added this, I was online!
In the UK we get these settings text to the phone, read and delete to update settings and I was surprised in Canada this wasn't done. Phone was blind and tech support didn't know to check this.
Now you've shown us how to configure the APN to work, I'd love to see if theres a thread or page on Rogers with the very latest settings, should these be older or mising some details. After all, will the wrong APN details upset a phone plan?
Thank you for your priceless help.
NP lol. And do the apn wouldn't upset the plan.
there is also 1 more apn that I use now is
Name - Rogers
Apn - internet.com
User - wapuser1
pass- wap
And leave the rest I personally like this apn better.
smudgepost said:
I signed up just to thank you! Even the Rogers tech support didn't know what to do. Simple when you know, and my HTC Desire has zero APNs available. Soon as I added this, I was online!
In the UK we get these settings text to the phone, read and delete to update settings and I was surprised in Canada this wasn't done. Phone was blind and tech support didn't know to check this.
Now you've shown us how to configure the APN to work, I'd love to see if theres a thread or page on Rogers with the very latest settings, should these be older or mising some details. After all, will the wrong APN details upset a phone plan?
Thank you for your priceless help.
Click to expand...
Click to collapse
Sent from my X10i TripNMiUI using Tapatalk
Hi I'm from canada and i'm having a problem with getting my phone to work.
I recently bought a Desire HD brand new from telus and am trying to use it on rogers. At first I got a unlock code and put in the rogers apn settings and did the *#*#4636#*#* and set it to unknown ( which i read online ) and it was showing 3g and was working fine.
Then the next day I took the sim card out to back up the numbers on my old phone, but every since then I haven't been able to get 3g again. At first it was just showing g , now it stays on wcdma preferred in the *#*#4636#*#* settings. It also won't allow me to select rogers keeps saying that the sim card does not allow me to select this carrier even though it is a rogers sim card.
I have also restarted it and turned it off many times, made sure that both the sim and sd cards were in properly and still nothing.
Please if anyone can help me with this , I really like the phone but my patience is running out with it .

Question about Arc S 3G

Hey, I have the L18i Arc S and am unable to get 3g thorough T Mobile or At&t in New York. Now my question is, would I be able to get 3G through any of the service providers by flashing a different ROM ? I know T Mobile frequency doesn't allow that so I guess the only choice left is At&t. Is there anything I can do to get 3G through At&t on my L18i Arc S ?
No, you should have bought a LT18a.
LT18i has no 3G connection is the states as it's missing the US specific frequencies for 3G and 4G/HSPA+
Sent from my iPad 2 using Tapatalk
please help.... LT18a no 3G under straight talk
hey guys, i'm new to XDA. I didn't want to make a new post because it seems that my question has been asked. unfortunately my issue is a bit more technical, I recently bought a lt18a and for the past week I have not been able to get 3G to work. I found a work-around that Straight Talk works under AT&T network so I didn't have to pay their insane prices, but the 3G is not coming up no matter where I went. (I looked up an AT&T tower, drove there just to test out the phone and still nothing) I bought the SIM from straight talk's site and followed their direction on the APN settings I got EDGE to work but no 3G.
I have called straight talk but their infamous awful tech support was no use to me. I also check on other forums and still nothing.
current APN settings:
Network Mode: GSM only
my APN settings
name: Straight talk
APN: att.mvno
Proxy: mvno.tracfone.com
port: 80
username: <not set>
password: <not set>
server: <not set>
MMSC: ( won't let me type this here )
MMS proxy: 66.209.11.33
MMS Port: 80
MCC: 310
MNC :410
authentication type: PAP or CHAP
APN type: <not set>
please help!
HELP!
ziontnk said:
hey guys, i'm new to XDA. I didn't want to make a new post because it seems that my question has been asked. unfortunately my issue is a bit more technical, I recently bought a lt18a and for the past week I have not been able to get 3G to work. I found a work-around that Straight Talk works under AT&T network so I didn't have to pay their insane prices, but the 3G is not coming up no matter where I went. (I looked up an AT&T tower, drove there just to test out the phone and still nothing) I bought the SIM from straight talk's site and followed their direction on the APN settings I got EDGE to work but no 3G.
I have called straight talk but their infamous awful tech support was no use to me. I also check on other forums and still nothing.
current APN settings:
Network Mode: GSM only
my APN settings
name: Straight talk
APN: att.mvno
Proxy: mvno.tracfone.com
port: 80
username: <not set>
password: <not set>
server: <not set>
MMSC: ( won't let me type this here )
MMS proxy: 66.209.11.33
MMS Port: 80
MCC: 310
MNC :410
authentication type: PAP or CHAP
APN type: <not set>
please help!
Click to expand...
Click to collapse
Hello all. This is my first post as well and My friend has the same problem. I did research all over the web and i can't find a normal explanation to why it wont work on AT&T 3G HSPA + network. Does anyone have any info on this matter? All help is greatly appriciated.
If you set it to GSM only, then 3G is turned off/not in use. You need to set it to use WCDMA preferred.
Sent from my Xperia Arc S using xda premium
Someguyfromhell said:
If you set it to GSM only, then 3G is turned off/not in use. You need to set it to use WCDMA preferred.
Sent from my Xperia Arc S using xda premium
Click to expand...
Click to collapse
Thank you! I will try. Do you have the same phone running on ST network @ 3g speed?
4tele said:
Thank you! I will try. Do you have the same phone running on ST network @ 3g speed?
Click to expand...
Click to collapse
I use my Arc S in 3G, but I live in Europe.
Sent from my Xperia Arc S using xda premium

[Q] CM10 ATT - h+ but no 4G

I finally got around to flashing CM10, but can't seem to get the 4G working. I get H+/3g data, but no 4g. I flashed the CM10 nightly from 10/2.
My IMEI is in tact, I know the modem I am using works correctly in this area.
Here if my APN information:
Code:
Name: ATT LTE
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMSC: hXXp://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Athentication Type: None
APN type: default,supl,mms
APN protocol: IPv4
APN enable/disable: enabled
Bearer: unspecified
Has anyone else run into a similar problem?
I realized I had a similar problem on CM9 and found two things:
1) APN type: default,supl,mms,hipri
I added hipri to APN type (not 100% sure it was needed)
2) In mobile network settings I had not selected LTE in the Network Mode option list. (THIS was my problem) It's one of those, duh of course I have that set moments..when I really didn't. So double check that setting.
thefightforgood said:
I finally got around to flashing CM10, but can't seem to get the 4G working. I get H+/3g data, but no 4g. I flashed the CM10 nightly from 10/2.
My IMEI is in tact, I know the modem I am using works correctly in this area.
Here if my APN information:
Code:
Name: ATT LTE
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMSC: hXXp://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Athentication Type: None
APN type: default,supl,mms
APN protocol: IPv4
APN enable/disable: enabled
Bearer: unspecified
Has anyone else run into a similar problem?
Click to expand...
Click to collapse
First of all...are you in an LTE area? When you were on an ATT rom did it say 4G LTE or just 4G?
rquinn19 said:
First of all...are you in an LTE area? When you were on an ATT rom did it say 4G LTE or just 4G?
Click to expand...
Click to collapse
I believe THIS was my problem. On ATT roms it would say 4G (I'm not in an LTE area) - apparently on CM roms this translates to H+. Looks like I never really had a problem at all.
Thanks! Consider this solved.
You shouldnt refere to to LTE/HSPA+ as 4G. Just name it by what it is. Much eqsier to identify what the problem area is.
Sent from my SAMSUNG-SGH-I747 using xda premium
When it comes to CM ROMs HSPA+ will be identified by and "H" and LTE by a 4G
Sent from my SAMSUNG-SGH-I747 using xda app-developers app
I finally got around to flashing CM10, but can't seem to get the 4G working. I get H+/3g data, but no 4g. I flashed the CM10 nightly from 10/2.
My IMEI is in tact, I know the modem I am using works correctly in this area.
Here if my APN information:
Name: ATT LTE
APN: pta
Proxy: not set
Port: not set
Username: not set
Password: not set
Server: not set
MMSC: hXXp://mmsc.mobile.att.net
MMS Proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Athentication Type: None
APN type: default,supl,mms
APN protocol: IPv4
APN enable/disable: enabled
Bearer: unspecified
Click to expand...
Click to collapse
Has anyone else run into a similar problem?
Click to expand...
Click to collapse
Change the following in your APN settings this resolved many 4g signal issues. I take no credit for this whatsoever. This was from another poster and I had these settings saved I just can't seem to find his post otherwise I would have linked it directly. If you happen to come across it be sure to hit the thanks button. If it really helped you donations wouldn't hurt for the original poster. Thank you. -
APN type:default,admin,fota,mms,supl,hipri,internet
APN protocol :IPv4/IPv6 (this setting experimental and is optional)
(make sure NO spaces after commas)
BEARER: LTE
Sent from my SGH-I747 using xda app-developers app
Have you actually ran speed test to confirm network speed?
Im actually having the same problem... Im using the infuse 4g with a cyanogen 4.2.1. Iunlocked my phone and am using a t-mobile sim (therefore, towers) and even though my phone is staying in one place the signal is going from E (econ, 2g) to 3g and H ( basically 3.5g) (back and forth) and never really stops...also the signal will be at full bars, then drop to no service and do it all over again.
Im obviously having service problems when i shouldnt and im not sure if im getting 4g at all even though i called and they said my plan was full-time 4g depending on coverage... OR..." H " is mobil's name for 4g (actually HSPDA + HSUPA which is technically considered 3.5).. Any help on the matter would be greatly appreciated.

T-Mobile 4G on ATT GSIII

Hi
So long story short, my Tmo GS3 got stolen at my work :/
So my mom gave me her ATT GS3 cus she was up for an upgrade,
i been reading its possible to get 4G on an ATT GS3 but so far no luck,
i know i have the right APN cus i copied the one from my Nex4 to my GS3, i set the network to manual and choose Tmo, but still all i get is Edge.
Does it have to do something with the way i unlocked the phone?
I been reading it has to be factory unlock and i unlocked mine by dialing *#197328640# and doing the required steps.
Can anyone help me with this?
orphan22 said:
Hi
So long story short, my Tmo GS3 got stolen at my work :/
So my mom gave me her ATT GS3 cus she was up for an upgrade,
i been reading its possible to get 4G on an ATT GS3 but so far no luck,
i know i have the right APN cus i copied the one from my Nex4 to my GS3, i set the network to manual and choose Tmo, but still all i get is Edge.
Does it have to do something with the way i unlocked the phone?
I been reading it has to be factory unlock and i unlocked mine by dialing *#197328640# and doing the required steps.
Can anyone help me with this?
Click to expand...
Click to collapse
Do a little bit of search work; it depends on the coverage for T-Mobile in your area. It's still a Work in Progress to get the 1700 Mhz band to work on a ATT GS3 since there's a bounty for it in the General section.
Setting the APN to what you have on the Nex4 won't do anything because it's all software and hardware controlled. The software part is currently locked down because no one knows what to change to get the hardware to send and recieve information from the 1700Mhz Band.
Your best bet is to check the coverage map and hope you get 3G service or wait until T-Mobile Rolls out their 4G so the old EDGE will switch onto HSPA for ATT devices that use a T-Mobile Network.
Hope this helps
hD
orphan22 said:
Hi
So long story short, my Tmo GS3 got stolen at my work :/
So my mom gave me her ATT GS3 cus she was up for an upgrade,
i been reading its possible to get 4G on an ATT GS3 but so far no luck,
i know i have the right APN cus i copied the one from my Nex4 to my GS3, i set the network to manual and choose Tmo, but still all i get is Edge.
Does it have to do something with the way i unlocked the phone?
I been reading it has to be factory unlock and i unlocked mine by dialing *#197328640# and doing the required steps.
Can anyone help me with this?
Click to expand...
Click to collapse
I was wondering myself smdh when im in landover md. I get good 4g. And soon as get greenbelt md all get is edge. Or maybe 3g. Or h
Sent from my SGH-I747 using Tapatalk 2
Try these apn settings if they arent what you're already using. They've worked for S3 users before.
Name: Straight Talk
APN: att.mvno
Proxy: <not set>
Port: <not set>
MMSC: http://mmsc.cingular.com
MMS Proxy: 66.209.11.33
MMS Port: 80
APN Type: default,supl,mms,hipri
xBeerdroiDx said:
Try these apn settings if they arent what you're already using. They've worked for S3 users before.
Name: Straight Talk
APN: att.mvno
Proxy: <not set>
Port: <not set>
MMSC: http://mmsc.cingular.com
MMS Proxy: 66.209.11.33
MMS Port: 80
APN Type: default,supl,mms,hipri
Click to expand...
Click to collapse
Arent those att apns? I need it to work foor tmo...
Sent from my Nexus 4 using xda app-developers app
orphan22 said:
Arent those att apns? I need it to work foor tmo...
Sent from my Nexus 4 using xda app-developers app
Click to expand...
Click to collapse
correct. my mistake. posted the wrong ones. what are your current apn settings?
i came across these:
APN: epc.tmobile.com
Proxy:
Port:
Username:
Password:
Server:
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Proxy:
MMS Port:
MCC: 310
MNC: 260
Authentication Type:
APN Type: default,supl,admin,dun,mms
APN Protocol: IPv4/IPv6
APN Roaming Protocol: IPv4/IPv6
and this one as well.
Name : T-Mobile LTE
APN: fast.tmobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Protocol: WAP 2.0
MCC: 310
MNC: 260
APN Type: default,supl,admin,dun,mms
xBeerdroiDx said:
correct. my mistake. posted the wrong ones. what are your current apn settings?
i came across these:
APN: epc.tmobile.com
Proxy:
Port:
Username:
Password:
Server:
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Proxy:
MMS Port:
MCC: 310
MNC: 260
Authentication Type:
APN Type: default,supl,admin,dun,mms
APN Protocol: IPv4/IPv6
APN Roaming Protocol: IPv4/IPv6
and this one as well.
Name : T-Mobile LTE
APN: fast.tmobile.com
MMSC: http://mms.msg.eng.t-mobile.com/mms/wapenc
MMS Protocol: WAP 2.0
MCC: 310
MNC: 260
APN Type: default,supl,admin,dun,mms
Click to expand...
Click to collapse
In going to try them. Thanks a lot.
Sent from my Nexus 4 using xda app-developers app
HermitDash said:
Do a little bit of search work; it depends on the coverage for T-Mobile in your area. It's still a Work in Progress to get the 1700 Mhz band to work on a ATT GS3 since there's a bounty for it in the General section.
Setting the APN to what you have on the Nex4 won't do anything because it's all software and hardware controlled. The software part is currently locked down because no one knows what to change to get the hardware to send and recieve information from the 1700Mhz Band.
Your best bet is to check the coverage map and hope you get 3G service or wait until T-Mobile Rolls out their 4G so the old EDGE will switch onto HSPA for ATT devices that use a T-Mobile Network.
Hope this helps
hD
Click to expand...
Click to collapse
I get really good 4G over 18MB on my nex4.
Sent from my Nexus 4 using xda app-developers app
Hey orphan did it work
Sent from my SGH-T959V using xda premium
HolyGhostBoy1 said:
Hey orphan did it work
Sent from my SGH-T959V using xda premium
Click to expand...
Click to collapse
No :/ still only edge. Is there a way to know what band 1700Mhz for example do i get in mi zone?
Sent from my Nexus 4 using xda app-developers app
I had the same situation: only edge, after flashing this files i have 4g http://forum.xda-developers.com/showthread.php?t=1771021&page=25.
Start reading from post #246. If you flash the files you must root your phone like it is a t999, also goes for recovery, im not sure about kernel and DO NOT flash another modem/radio.

No network on US version with ATT

Hi, I was wondering if anyone else had a similar problem or can help with a solution. I just got my Oppo 7 (love this thing) but it seems the network doesn't work properly. The network seems to be picked up just fine, full bars, under network settings it automatically acquires the APN settings and everything, but I can't do anything over the air without WiFi. As soon as the WiFi is gone, I can't browse the internet, send or receive text messages, etc. What do?
Will this help? Won't be LTE, but H+ (my phone doesn't have LTE)
APN: att.mvno
Proxy : wireless.cingular.com
Port: 80
MMSC: http://mmsc.cingular.com
MMS Port: 80
MCC: 310
MMC: 410
APN Type: default,supl,mms
APN Protocol: IPv4
APN Roaming: IPv4
Chuteboxe39 said:
Hi, I was wondering if anyone else had a similar problem or can help with a solution. I just got my Oppo 7 (love this thing) but it seems the network doesn't work properly. The network seems to be picked up just fine, full bars, under network settings it automatically acquires the APN settings and everything, but I can't do anything over the air without WiFi. As soon as the WiFi is gone, I can't browse the internet, send or receive text messages, etc. What do?
Click to expand...
Click to collapse
I have mine set up on T Mobile and I'm having the same problem. It's pretty annoying. I've tried a factory reset to no avail. My phone downloaded an update this morning which I hoped would fix the problem, but it looks like it hasn't.
Chuteboxe39 said:
Hi, I was wondering if anyone else had a similar problem or can help with a solution. I just got my Oppo 7 (love this thing) but it seems the network doesn't work properly. The network seems to be picked up just fine, full bars, under network settings it automatically acquires the APN settings and everything, but I can't do anything over the air without WiFi. As soon as the WiFi is gone, I can't browse the internet, send or receive text messages, etc. What do?
Click to expand...
Click to collapse
That's odd. There's one thing wrong with this device on stock - its APN database for AT&T is 3-4 years out of date. It was still using the wap.cingular APN when I turned mine on.
You need to manually put in the AT&T LTE APN (pta). ALSO if you've never owned an LTE device before you'll need to talk to AT&T to have your account updated. (Using the pta APN with a Nexus 5 resulted in no data for me too until I had my plan/account updated. You can do this without an actual contract change - for example I'm still grandfathered in to "unlimited data"). In general I would recommend doing this in-person at an AT&T-owned store, not at the phone and not at a franchisee (like most small mall kiosks).
Thanks for the reply everyone, I entered in the new ATT HSPA+ APN and it works like a charm now.
Could you post your settings?. I confirmed the SIM I got yesterday was lte capable but still no dice.
Sent from my X9006 using XDA Free mobile app
jgunna405 said:
Could you post your settings?. I confirmed the SIM I got yesterday was lte capable but still no dice.
Sent from my X9006 using XDA Free mobile app
Click to expand...
Click to collapse
Just putting in the pta APN with no other info was enough for me.
(MMS is probably borked for me until I fill in the right settings for it but I use MMS maybe once every 3 years at most.)
Entropy512 said:
Just putting in the pta APN with no other info was enough for me.
(MMS is probably borked for me until I fill in the right settings for it but I use MMS maybe once every 3 years at most.)
Click to expand...
Click to collapse
I just realized that you were in here Entropy. I appreciate the work you did with the Galaxy S2 (last phone I had before this one). Do you plan on doing any dev work with this one or are you going to take it easy?
mmsc: http://mmsc.mobile.att.net
mms proxy: proxy.mobile.att.net
mms port: 80
apn type: default,mms.supl
That's what I have currently and mms works fine.
jgunna405 said:
I just realized that you were in here Entropy. I appreciate the work you did with the Galaxy S2 (last phone I had before this one). Do you plan on doing any dev work with this one or are you going to take it easy?
mmsc: http://mmsc.mobile.att.net
mms proxy: proxy.mobile.att.net
mms port: 80
apn type: default,mms.supl
That's what I have currently and mms works fine.
Click to expand...
Click to collapse
I'm working on lighting up omni. Oppo sent us a few devices.
Thanks for the MMS info, I should stick that into my device.
jgunna405 said:
I just realized that you were in here Entropy. I appreciate the work you did with the Galaxy S2 (last phone I had before this one). Do you plan on doing any dev work with this one or are you going to take it easy?
mmsc: http://mmsc.mobile.att.net
mms proxy: proxy.mobile.att.net
mms port: 80
apn type: default,mms.supl
That's what I have currently and mms works fine.
Click to expand...
Click to collapse
I pulled the APN configs for ATT Phone APN from omni's github (I updated it a few months back to what it was from an AT&T stock TouchWiz Galaxy S4 ROM, so it this is update-to-date afaik)
I've bolded the ones that you actually need to touch, otherwise, don't touch them
Name: ATT Phone
APN: phone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not set
MMSC: http://mmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Authentication type: Not set
APN type: default,subl,mms,hipri (no spaces between them!!!!)
APN protocol: IPv4
APN roaming protocol: IPv4
APN enable/disable: APN enabled (this should be grayed out anyway)
Bearer: Unspecified
jakew02 said:
I pulled the APN configs for ATT Phone APN from omni's github (I updated it a few months back to what it was from an AT&T stock TouchWiz Galaxy S4 ROM, so it this is update-to-date afaik)
I've bolded the ones that you actually need to touch, otherwise, don't touch them
Name: ATT Phone
APN: phone
Proxy: Not set
Port: Not set
Username: Not set
Password: Not set
Server: Not set
MMSC: http://mmmsc.mobile.att.net
MMS proxy: proxy.mobile.att.net
MMS Port: 80
MCC: 310
MNC: 410
Authentication type: Not set
APN type: default,subl,mms,hipri (no spaces between them!!!!)
APN protocol: IPv4
APN roaming protocol: IPv4
APN enable/disable: APN enabled (this should be grayed out anyway)
Bearer: Unspecified
Click to expand...
Click to collapse
I have this as my settings now and still only get H+. (except for the mmsc, you have 3 m's)
Weird thing is that I get 0 connection when I change from phone to pta.
Not sure if locale is the culprit. I'm in Oklahoma City.
Sent from my X9006 using XDA Free mobile app
jgunna405 said:
I have this as my settings now and still only get H+. (except for the mmsc, you have 3 m's)
Weird thing is that I get 0 connection when I change from phone to pta.
Not sure if locale is the culprit. I'm in Oklahoma City.
Sent from my X9006 using XDA Free mobile app
Click to expand...
Click to collapse
whoops made a typo, yea it's only 2 m's in mmsc
try applying ATT Phone apn and rebooting,,
that's weird. did you call AT&T to confirm that you have the LTE data package on your account like Entropy512 stated ?
jakew02 said:
whoops made a typo, yea it's only 2 m's in mmsc
try applying ATT Phone apn and rebooting,,
that's weird. did you call AT&T to confirm that you have the LTE data package on your account like Entropy512 stated ?
Click to expand...
Click to collapse
I went to the ATT store, but they weren't any help. They confirmed that the SIM they gave me was lte compatible, but I assumed that's the same thing as having an LTE data package. I'll give them a call tonight and let you all know. (btw, just re-applied your settings and still no luck)
edit: called.. and they claim that all accounts have lte compatibility now and of course she had never heard of the OF7a
The settings entropy posted were the exact settings my N5 had which I copied over and worked fine. One thing to be aware of is that mine says 4G on LTE and then either H or H+ for those, not sure if this applies only to my service area or what and another might show differently. At any rate if you're getting 4G showing you might wanna run speedtest and see if you are getting LTE.
jgunna405 said:
I went to the ATT store, but they weren't any help. They confirmed that the SIM they gave me was lte compatible, but I assumed that's the same thing as having an LTE data package. I'll give them a call tonight and let you all know. (btw, just re-applied your settings and still no luck)
edit: called.. and they claim that all accounts have lte compatibility now and of course she had never heard of the OF7a
Click to expand...
Click to collapse
AT&T's SIMs have been LTE compatible for years, even before AT&T had an LTE network. I need to check to be sure, but I'm fairly certain my SIM is still the original "cut down SIM" that I've had since 2011 at least.
It's your account that needs to be LTE-enabled.
Don't call. Phone support is awful. Go to a corporate-owned AT&T physical store. That's where the competent staff are.
(In my case, I originally did the LTE upgrade on a Nexus 5 - if you put a SIM into a Nexus 5 that doesn't have LTE on the account, you'll get a text message saying to call AT&T.)

Categories

Resources