Develop Bugs

[Q] low battery shutdown

whats the latest on the battery? i've read a lot of posts here about shutdown but not really found an answer. i have 2 different batteries, std 1350 and a 1600 which i swap as needed so i dont expect the battery meter to be really accurate, but it seems that either battery goes from about 25% then just dies. not sure if it actually shuts down cleanly on low power but certainly there is no warning.
apart from carrying a spare (which i do) whats the best work around?
i've no idea what a real android phone does when the battery is low.

in theory android shutdown the phone before the battery level is too low.
But on low battery values or when you switch between battery the kernel hasn't a good battery level resolution, so the battery run out before android can shutdown.

gazzacbr said:
whats the latest on the battery? i've read a lot of posts here about shutdown but not really found an answer. i have 2 different batteries, std 1350 and a 1600 which i swap as needed so i dont expect the battery meter to be really accurate, but it seems that either battery goes from about 25% then just dies. not sure if it actually shuts down cleanly on low power but certainly there is no warning.
apart from carrying a spare (which i do) whats the best work around?
i've no idea what a real android phone does when the battery is low.
Click to expand...
Click to collapse
The kernel re-calibrates the battery level based on voltage and current when it first boots after the battery has been removed. The calibration is not very accurate, and might be off by 10 or even 20 percent. But, when the voltage drops low enough, the kernel will calibrate the battery level again, and you should see it reading under 5% before it dies. The actual shutdown happens when the battery sensor detects 3V or less. In the kaiser, that doesn't seem to be controlled by the kernel, so I think we can't do anything about it. I don't think we want to, either, since it is quite bad to run a Lithium Polymer battery at less than 3V. It would be nice to have an interrupt at 3V instead of an abrupt shutdown, so we could do a clean shutdown. Except, of course, we haven't yet figured out that clean shutdown.
If your kernel is older than November 6th, or if you use 2.6.25, you should update to a more recent 2.6.32 kernel for better battery readings.

Battery Problem

I've gotten my seidio extended battery and have never really tested it to its limits. I would like to have it functioning optimally. I have the app "Battery Monitor" installed which can calculate the percentage left via the voltage as opposed to the stock battery indicator. I am currently showing 57% via the voltage monitor and 35% via the stock monitor. I have found that my battery can drop to ~1% (according to the stock indicator) however the voltage indicator would be at something like ~30%...my phone would turn itself off at that point in time and I would not be able to take advantage of the reported battery....I have followed directions from: droidxforums.com/forum/droid-x-general-discussion/18216-disable-low-battery-warning.html...I bootstrapped and reset the battery...but nothing. I was wondering if anyone has had any experience in this or could help me out.
Thank you.

I think if you go into the screen where you clear the Dalvik Cache in the recovery menu there's a battery settings function. If i've read some of these posts correctly, that calibrates the phone to the battery. basically re-adjusts the 0-100 range on the phone.
You need to do this when the battery is fully charged.

Draining your battery all the way down will destroy your batteries capability of holding a charge in the future.
Your phone is suppose to only charge to ~90% and cut off at ~10%.
Ultimately this means you are only using 80% of your battery, but it's how Li-Ion batteries works.
If you truly drain it all the way down you ruin the battery.
There are some things you can do to recalibrate the software that determines the charge level of the battery though, like the above post suggests.
I don't know if you're running a custom ROM, but if you are or aren't you should definitely check into changing your phones Kernal to Chad's or IncrediKernals. They drastically improve battery life.
For me, it gave massive improvements for 'screen off' (1% depletion every 1 hour) and significant improvements when using the phone.
Of course I'm using the HTC extended battery, but that was much better than the 3-5% per hour I got before.

hello,
please tell me what's wrong with my xda iis. when the power below 75% and i activated wifi/camera/any apps, oftenly it turn off by itself. also, it often signal loss or cannot make/receive calls. thanxs

[Q] Weird battery discharge

Hi fellas..
Maybe you've noticed the messages I've sent to Unofficial BravoS thread of Coolexe's (http://forum.xda-developers.com/showthread.php?t=1200517&page=51) which is the ROM I use.
The issue is, the battery discharges rapidly. Actually, if you check mV values, it doesn't discharge rapidly, but if you look at percentages, there is a huge inconsistency. I used Battery Monitor Widget to log the battery performances last night, and saw these horrible results:
Code:
2011/09/19|04:59:49|-515mA|37%|3581mV|40.2ºC|1|0
2011/09/19|05:00:51|-465mA|36%|3576mV|40.2ºC|1|0
2011/09/19|05:01:49|-460mA|36%|3576mV|40.2ºC|1|0
2011/09/19|05:02:50|-462mA|35%|3517mV|40.2ºC|1|0
2011/09/19|05:03:49|-477mA|35%|3517mV|40.2ºC|1|0
2011/09/19|05:04:50|-471mA|34%|3449mV|40.3ºC|1|0
2011/09/19|05:06:06|-478mA|0%|3415mV|40.5ºC|1|0
2011/09/19|05:06:08|-478mA|0%|3415mV|40.5ºC|1|0
These are the last lines of the log, before the phone shuts down. As you can see, the phone gone to 0% from 34% in one minute! No low battery warnings or whatsoever..
Funny thing is, this doesn't happen in StarBurst ROM (which is a Froyo based one). Do you reckon this is a GingerBread issue or something? I saw some other people complaining about their phone shutting down at 20% as well.
So, what do you suggest?

when you look at the voltage there isnt that much drain, so its only a displaying problem
wipe battery stats and maybe recalibrate the battery
but first one should fix it
cheers
ps: i just checked, my desire is at 18% with 3.693mV, now you see the differance

crendot said:
when you look at the voltage there isnt that much drain, so its only a displaying problem
wipe battery stats and maybe recalibrate the battery
but first one should fix it
cheers
ps: i just checked, my desire is at 18% with 3.693mV, now you see the differance
Click to expand...
Click to collapse
This is what I've done so far:
Drained battery to 0% (log above) and charged it a little bit while powered off (like 20%). Turned on the phone, and obtained those logs (last lines only):
Code:
2011/09/19|14:41:25|-268mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:42:25|-267mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:43:25|-270mA|10%|3644mV|38.1ºC|1|0
2011/09/19|14:44:25|-269mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:45:25|-267mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:46:25|-268mA|9%|3644mV|38.1ºC|1|0
2011/09/19|14:47:25|-266mA|8%|3644mV|38.1ºC|1|0
2011/09/19|14:48:25|-267mA|8%|3644mV|38.1ºC|1|0
2011/09/19|14:49:25|-269mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:50:25|-267mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:51:25|-266mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:52:25|-267mA|7%|3640mV|38.0ºC|1|0
2011/09/19|14:53:25|-267mA|6%|3640mV|38.0ºC|1|0
2011/09/19|14:54:25|-267mA|6%|3640mV|38.0ºC|1|0
2011/09/19|14:55:25|-267mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:56:25|-266mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:57:25|-267mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:58:25|-268mA|5%|3635mV|38.0ºC|1|0
2011/09/19|14:59:25|-268mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:00:25|-319mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:01:25|-268mA|4%|3630mV|38.0ºC|1|0
2011/09/19|15:02:25|-270mA|3%|3610mV|38.1ºC|1|0
2011/09/19|15:03:25|-269mA|3%|3610mV|38.1ºC|1|0
2011/09/19|15:04:25|-270mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:05:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:06:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:07:25|-273mA|2%|3586mV|38.1ºC|1|0
2011/09/19|15:08:25|-289mA|1%|3513mV|38.3ºC|1|0
2011/09/19|15:09:25|-290mA|1%|3513mV|38.3ºC|1|0
2011/09/19|15:09:51|-290mA|0%|3464mV|38.3ºC|1|0
It seems more "smooth" discharge now. Right now, I'm charging my phone off; going to turn on phone once it reaches "green light" with charger on, and plug it off once phone booted. Maybe then, it can know what's maximum and minimum.
So far, I tried to charge my phone to full and erase batterystats.bin but, as you can see at the first post, it didn't work well.. On the other hand, the phone charged-discharged only once in this ROM, you think it could be better if I've given a "second chance"?

i dont know much about that "battery calibrating" and reseting stuff, you have to search in the forum
only thing i want to say is, dont do that deep drains!
recharge at least 5%! you kill your battery, lithium-ion batterys get serious damage from deep drains

crendot said:
i dont know much about that "battery calibrating" and reseting stuff, you have to search in the forum
only thing i want to say is, dont do that deep drains!
recharge at least 5%! you kill your battery, lithium-ion batterys get serious damage from deep drains
Click to expand...
Click to collapse
I know, but when phone thinks it's 30% and not warn me, how can I do it?

In order to calibrate the battery meter - FYI the battery itself cannot be calibrated, as Li-Ion batteries have a very low memory compared to old Ni-Cd etc. batteries - you have to go through the following procedure:
1) charge the battery to 100%;
2) let the battery discharge until the phone shuts itself down;
3) plug the wall charger into the phone, boot the phone up then charge the battery to 100% without interruptions.
If the above procedure does not yield the expected results, you can try fully charging the phone (LED showing green) with it completely turned off (after completely draining it). Again, the charging procedure should not be interrupted.
Source: personal experience - had to do this twice after installing new ROMs, as the phone was shutting down at ~14% (working like a charm now).
Regarding the matter of battery wear because of complete discharges, Li-Ion batteries do indeed have a lower cycle count than old-school batteries, but the standard charge/discharge number a Li-Ion battery can take is ~350, so you can't damage the battery pack by doing a full cycle per month (required to keep the battery meter accurate).
Good luck!

TVTV said:
In order to calibrate the battery meter - FYI the battery itself cannot be calibrated, as Li-Ion batteries have a very low memory compared to old Ni-Cd etc. batteries - you have to go through the following procedure:
1) charge the battery to 100%;
2) let the battery discharge until the phone shuts itself down;
3) plug the wall charger into the phone, boot the phone up then charge the battery to 100% without interruptions.
If the above procedure does not yield the expected results, you can try fully charging the phone (LED showing green) with it completely turned off (after completely draining it). Again, the charging procedure should not be interrupted.
Source: personal experience - had to do this twice after installing new ROMs, as the phone was shutting down at ~14% (working like a charm now).
Regarding the matter of battery wear because of complete discharges, Li-Ion batteries do indeed have a lower cycle count than old-school batteries, but the standard charge/discharge number a Li-Ion battery can take is ~350, so you can't damage the battery pack by doing a full cycle per month (required to keep the battery meter accurate).
Good luck!
Click to expand...
Click to collapse
Thanks for your answer...
Today I realized that it my concern was a quick one. Today, I discharged battery to 0 percent, plugged the AC charger while it's OFF and charged it for around 2h22m until Led-green-full; then turned on the phone with charger plugged and plugged it off just after the boot process. After that, I let the phone to discharge (I helped it a little )
I actually saw "Plug your charger" warning this time, and according to Bat. Mon. Widget, it gone down until 13%! If I do compare the mV values with the old ones, I can see that somehow the phone does learn which mV value correspond to which percentage better.
Even though it gone from 13% to 0% in two minutes, it's at least better than 30% to 0%.. Also, when I check the readings after I plugged in, I saw that percentage-voltage matching is slightly higher, showing that the phone now shows lower percentage for the same voltage - which shows that it learns percentage better.
After one or two charge-discharge cycle, I think it'll learn absolute 0
BTW; the battery says 3.4V 1400mAh and my maximum voltage is 4160mV (100%) and minimum is 3415mV (0%). Are these values normal, you think?
PS: What I'd recommend from anyone who loves flashing ROMs as much as I do is: AFTER YOU FLASHED A NEW ROM, CHARGE YOUR BATTERY TO FULL (100%) AND ERASE THE BATTERY STATS. AFTER THIS, NEVER, I SAY, NEVER ERASE YOUR BATTERY STATS FOR LONG TIME IN ORDER FOR YOUR PHONE TO LEARN STATS BETTER! Erase after long time, say 3 months for wear effects to be accounted, but well, I think you should be fine even after you don't do this
Maybe you did already know that, but, well, I learned it hard way
EDIT: Phone shutdown at 13% after this, but I think it'll do better in time..

Can't Calibrate the Widget
I am having a similar issue with my htc aria. Problem is that it gets to about 78% and then won't go any higher. It even shows (in Battery Monitor Widget)
"Discharging" and "AC plugged". I have let it sit plenty long enough to be fully charged and then completely discharged it (until it shut itself down, which was not 0%) and recharged until it reaches 78% again and stops charging. I'm guessing it is so far out of whack that it says I'm at 78% but I am really at 100%.
The widget says to charge to 100% and then drain completely to 0% to calibrate. I can't do either from what I can tell. So what to do?

theGanymedes said:
Today, I discharged battery to 0 percent, plugged the AC charger while it's OFF and charged it for around 2h22m until Led-green-full; then turned on the phone with charger plugged and plugged it off just after the boot process.
Click to expand...
Click to collapse
Quick tip - let the phone charge for another hour or so after the light goes green (when charging it while powered off). I've read that the light goes green at about 95%. It takes another hour for the phone to really charge to 100%. That's because Li-Ion batteries use two stages to charge: a fast one and a slow one. More details here.
Glad i could help.
P.S. - It also took me two complete charge/discharge cycles to fully calibrate my battery meter after switching from FroYo to Gingerbread.
@vkyjackie - Try fully charging the phone while powered off. If it still doesn't fully charge (LED green), then you might have an issue with either the battery pack or the wall charger.

Battery charge from 80% to 100%=(

Hi, sry for my english=(
When i charge my battery its normally charge to 80% and then becomes 100%.
Try calibrate battery but this doesnt help. Also try another roms and kernels.
Is it a battery issue?

U can buy new battery from DEALEXTREME.com

so its the only way?

Try this.
Charge battery to full. Leave plugged in, Turn off fastboot in power settings and shut phone off. Light will turn orange again and let it charge til green. Boot into recovery and wipe battery stats. After this let the battery drain as low as 10% before recharging to full without unplugging. Do this a few times over a few days. If you don't get more accurate percentages after this then the battery could be messed up.

Gizmoe said:
Try this.
Charge battery to full. Leave plugged in, Turn off fastboot in power settings and shut phone off. Light will turn orange again and let it charge til green. Boot into recovery and wipe battery stats. After this let the battery drain as low as 10% before recharging to full without unplugging. Do this a few times over a few days. If you don't get more accurate percentages after this then the battery could be messed up.
Click to expand...
Click to collapse
thx i will try.

i have the exact same issue. i have done battery stat wipe..flashed multiple roms over and over with full wipe and all that. battery charges up to 80% then the LED turns green..and stays that way till it reaches 100%. it jumps from 80% to 100% in just a few minutes.

battery jump
I wouldn't worry Lendlord mine does the same (see attached pic) you can see the green line jumps up from 80 to 100 but doesn't jump down from 100 to 80 under use. The picture is taken from Battery monitor widget, it's a great app which shows mv, ma, % and temp and even keeps a text log of what ma drain there has been allowing you to monitor battery drain while you're using your phone or while it is sleeping.
Here's a great guide aswell of how to ensure best battery life by memnoc:
forum.xda-developers.com/showthread.php?t=1226016

so thats mean that some battaries have the same issue=( And there is no solution for it...
HTC failed again...
first GPS and now the battery. Bad, very bad!
And one more request.
Can someone post your current widget log?

LendLord said:
so thats mean that some battaries have the same issue=( And there is no solution for it...
HTC failed again...
first GPS and now the battery. Bad, very bad!
And one more request.
Can someone post your current widget log?
Click to expand...
Click to collapse
I have the same thing happen to mine, i think its because you've let your DHD die due to low battery levels and that damages the battery which i think causes this problem

..letting the phone shut off because of a completely discharged battery is NOT good for the lifetime of Li-ION batteries.
The battery could be hurt and the amount of mAh the battery is able to store might be lower after.
Also trying to 'pump' the battery to fully charge by connecting / disconnecting while the phone is down is not a good advice because li-ion batteries also don't like overcharging.
To be sure that the battery is fully charged due to its ability it is sufficient to let the phone be conectet to charger or usb overnight.
Android uses the voltage of the battery to estimate (!) the % charge value.
Android supposes the battery is fully charged when it enters the voltage of about 4.2 Volt which is the charging cut-off voltage for li-ion cells.
Now when charging again the conceded voltage is reached more quickly than estimated by android, so the system is 'surprised' of this rapid charge and changes the % value to 100% because the conceded voltage is reached more quicklyy as supposed.
(Try to fill a 0.5ltr beer bottle into a 0.33 glass)
This is the normal of aging for li-ion batteries.
Consider for yourself if it's acceptable for you or if you should by a new battery.
by the way... be careful with cheap china batteries for 10$.
Offers with exaggerated values (up to 1600mAh) will mostly keep their promises
only for the first two or three charges only and will than fall back to 800 mAh or even less !
Greetz
Pudel

Yeah...
My battery started to do the same thing for a week or two. It will charge to 86% then it jumps to 100%, saying it's charged.

This is normal afaik, nothing to worry about.
Sent from my Desire HD using xda premium

solve
actually，it's the problem of your rom , in the framwork.apk . unzip it you will get a lot of battery icon form 1%to 100% in the res file ，if it made mistake，that 'your problem. you can go to uot kitchen to coustom it again.

Nope!
I've solved my problem. I've bought a new (original) htc battery, and the new one works great. I haven't reflashed the rom, or made any new modification. Just added the new battery.
So, yes, it's a faulty battery.

LendLord said:
Hi, sry for my english=(
When i charge my battery its normally charge to 80% and then becomes 100%.
Try calibrate battery but this doesnt help. Also try another roms and kernels.
Is it a battery issue?
Click to expand...
Click to collapse
Download Current widget from market and charge ur phone then wait for the 0 ma then download the battery calibration app from market too and calibrate and unplug ur phone, u can aslo reboot to recovery and wipe battery stats hope it helped you

Shutdown at ~25% with new battery and 20% with old

Hello,
I've read the threads about battery in the desire, BATT FIX with new kernels etc but can't really find a definite answer for my problem.
I bought my phone 18 months old and from the beginning it has shut down at about 20%. Tried the battery thing with charging, on/off, charing again etc, wiping battery stats etc but it doesn't seem to matter. So, I thought I'd just buy a new battery and be done with it.
The new battery arrived yesterday (actually, it's a used battery from customer returns but seller tells me it's been tested to be in mint condition). So this battery shows 3% when I first start up with it, "good, this seems to work" I think. But when at 75% the charger indicator (LED light) all of a sudden turns green and battery % jumps straight to 100%. I do the battery calibration trick with on/off charge and wipe battery stats. Stuck at 100% for some time as reported by others trying this "trick", have been using it all day and it shuts down at 25% even worse than the other battery...
The best voltages I've seen on this supposedly new battery is 4,144 and somewhere above 3.5 (nowhere near 3.2 and 4.2). What strikes me as odd is that I get very close to the same values with my old battery so I'm starting to think that maybee both battery are good but the phone reports way wrong values...is this possible?
Battery life with phone and data connection on, 1 gmail account but disabled backup feature (no GPS, BT etc) gives me -5% after 10 hours standby and I can use the phone for browising, light gaming for about 3 hours and 40 minutes before it dies (more or less constant usage at very low autobrightness levels and Turbo 3G enabled).
If someone has some insight into this it would be really helpful before I contact the eBay seller for this particular battery.
Regards, Olle

Same thing
My phone shuts down at 35% now... Is that a problem with the chipset or what? Only with Alex-V's calibrated kernels my phone shuts down at 0%, and sometimes it decalibrates too, but after calibration is Okay. I wonder if i need a new battery or my chipset has issues.