Related
Is this the highest?
http://www.seidioonline.com/product-p/pmc.htm
Post links if you know of higher ones, thank you.
Sent from my ADR6400L using XDA App
There are 2.1A usb adapters, but I don't think microUSB can take advantage of it. The one you linked is a 1A, which is the same as the wall charger HTC gave with the phone. I'm currently using a 1A usb adapter in my truck.
Ok that's probably what I'm looking for then. Are there wall chargers greater than what came with the phone that I can take advantage of?
Your best bet would be to try the USB adapters made for iPads. The Apple products can utilize the 2.1A chargers with their sync cables, but I'm not sure if a microUSB cable can though. I have some 2.1A wallchargers from some of my Apple products, I'll test them later and let you know what I find out.
http://www.verizonwireless.com/b2c/...ryDetails&archetypeId=12299&accessoryId=46370
I just got an Enercell from Radio Shack with dual usbs. Max output is 2.5A divided between the two ports.
http://www.radioshack.com/product/index.jsp?productId=11329448
on sale now for only $14.99. Seems to be of good quality.
The Motorola rapid chargers rock.
Guys, unless you mod the usb adapter 5V spec, you aren't doing squat with a "high power" adapter. The device has an input impedence that will draw a certain amount of current at 5v., and that's it.
Standard battery: 1400 mAh
Time to charge: 4 hrs (according to manual)
That's 1400/4 = 350 mA.
Most adapters on the market spec more than that, they're usually 500 mA or above. And again, unless you boost the volts, you're not going to be able to push more than 350 mA or so.
So don't waste you're money.
On the other hand, if your going to share a car outlet with another device like mp3 or ipod, then yeah, you'll need a higher output, two port, adapter.
Edit: It just occurred to me that if you're using the phone heavily while charging, then yeah you may need more than 500 mA. My currrent widget shows the phone can draw another 250 mA or so during use. That plus the charge totals to around 600 mA. But depending upon design, the phone may not be able to pull in all 600 mA. A test with a current meter would be real interesting.
The charger shipped with the Thunderbolt is a 1 Amp charger.
If I use a 500 mA charger the Current Widget shows a +450mA charge current. However if I use the 1A charger, I get a charge current of about +850mA.
Given that the google navigation gobbles over 400mA when running, you need a car charger with greater than 500mA capacity of you want the phone to charge at the same time.
Sent from my ADR6400L using XDA App
boingboingbilly said:
The Motorola rapid chargers rock.
Click to expand...
Click to collapse
Good to hear, I ordered one today for $11 on ebay. I had heard other people say they liked that one too.
Ecomaniac said:
Guys, unless you mod the usb adapter 5V spec, you aren't doing squat with a "high power" adapter. The device has an input impedence that will draw a certain amount of current at 5v., and that's it.
Standard battery: 1400 mAh
Time to charge: 4 hrs (according to manual)
That's 1400/4 = 350 mA.
Click to expand...
Click to collapse
You're making the incorrect assumptions that the charging rate is constant, and charging is 100% efficient. Li-ion batteries can be charged at up to a 1C rate (i.e. 1.4A for a 1400 mA cell). Add the power drawn by the phone itself, and a 1.8 Amp charger might not be unreasonable (1.8 A is the specified limit for micro USB connectors). Whether the phone will actually do a maximum rate charge, I don't know.
This, from a TI Application Note (Google for SLAA287, board won't let me post links):
A Li-Ion battery charging process consists of three stages:
· Slow Charge: Pre-charging stage using current of 0.1C
· Fast Charge: Constant current charging stage using current of 1C
· Constant voltage charging stage
During the slow charge stage, the battery is charged with a constant low charge current of 0.1C, if the battery voltage is below 2.5V. The slow charge stage is rarely used during the charging process of a Li-Ion battery.
The fast charge (constant current) and constant voltage charging are the most important stages during a recharge process. Most Li-Ion batteries have a fully charged voltage of 4.1 or 4.2V.
The battery is first charged with a constant current of 1C until a battery voltage reaches 4.1 or 4.2V. The firmware continuously checks the charging current by sensing the voltage at the current sense resistor (Rsense) and
adjusts the duty cycle of PWM output from the MCU. The battery's voltage is checked frequently.
Whenever found the battery's voltage reaches 4.1 or 4.2V, the charger will switch to constant voltage charging mode. The battery is then charged with a constant voltage source at a fixed battery voltage of 4.1 or 4.2 V...When the charging current falls below 0.1C, the charging process must stop.
Click to expand...
Click to collapse
Monoprice has Cig to USB(1A) chargers and the USB to Micro cables in multiple lengths(I ordered 6' ones) for far cheaper than you will find anywhere else
mike.s said:
You're making the incorrect assumptions that the charging rate is constant, and charging is 100% efficient. Li-ion batteries can be charged at up to a 1C rate (i.e. 1.4A for a 1400 mA cell). Add the power drawn by the phone itself, and a 1.8 Amp charger might not be unreasonable (1.8 A is the specified limit for micro USB connectors). Whether the phone will actually do a maximum rate charge, I don't know.
This, from a TI Application Note (Google for SLAA287, board won't let me post links):
Click to expand...
Click to collapse
very useful, thanks!
walbuls said:
Monoprice has Cig to USB(1A) chargers and the USB to Micro cables in multiple lengths(I ordered 6' ones) for far cheaper than you will find anywhere else
Click to expand...
Click to collapse
I second monoprice.
I tried bunch of cig to usb car charger and none matched advertised output... They all showed Charging (USB). I now use AC inverter and it charges just like a wall charger.
eccenpix said:
I tried bunch of cig to usb car charger and none matched advertised output... They all showed Charging (USB). I now use AC inverter and it charges just like a wall charger.
Click to expand...
Click to collapse
I suspect you need to find one which properly follows the USB Battery Charging Specification. That link is to the most recent version, which came out on 7Dec2010 (remember Pearl Harbor!). Version 1.1 is easier - a Dedicated Charging Port is indicated by shorting together the data lines (the two middle conductors on a full sized USB connector. By doing so, it indicates the device may try to draw up to 1.8 A of current (although a dedicated charging port is allowed to limit the current to less than that, it must provide at least 1.5 A).
I bought a cheap USB hub with 5 ports, used an exacto knife to cut the traces going to the data lines (the middle two) on all the ports, and then shorted them together on each port. It's now no longer a USB hub, but a USB charger with 5 ports I can used to charge stuff (phone and Bluetooth, quite often). The AC adapter which it came with does 2 Amps. My Thunderbolt says "Charging (AC)" when plugged into it.
So, if you can open up one of your adapters, just solder a jumper between the middle two contacts (make sure they're not connected to anything else).
Just got the Rocketfish premium microUSB at Best Buy and it has a captive coiled cord and a USB port. TBolt says "AC plugged" and reads +670 mA.
Good choice on the Motorola Rapid Charge - I've burned through 3 other cheap car chargers trying to keep my phone alive while using Google Nav and this is the first one to work!
i have the rapid motorola one on amazon
lippstuh said:
i have the rapid motorola one on amazon
Click to expand...
Click to collapse
+1 Works great! Battery widget usually shows about +800mA while only charging. Real close to the wall charger
Hi,
I've lost my charger, and I don't know if I can charge it with a charger with 5v - 1A or not, what I do know is that charging with USB is 5v - 500mA.
What's the power of the SE Arc original charger?
On the charger it says output 5V 1A
Is that what your looking for
It's Exactelly what I'm looking for thank you very much
The original SE charger for the arc is the GreenHeart charger EP800. It has got an output of 5V; 850mA.
As far as I know, there's no SE charger with an output of 1A. I've seen chargers with 500mA, 700mA and the 850mA.
My charger got fried during a power surge while holidaying in India so after asking around on the forum, I bought a Nokia AC-10N charger with an output of 5V, 1200mA. I've been using it without any problems. Pretty happy with it. Charges the phone much faster.
Thank you, that helps very much, but I heared charging the phone with higher voltage or higher Amperage can charge it faster, but it lowers the battery life on the long terme, it's appreciated to charge it with lower power in order to preserve battery life
MehdiArc said:
Thank you, that helps very much, but I heared charging the phone with higher voltage or higher Amperage can charge it faster, but it lowers the battery life on the long terme, it's appreciated to charge it with lower power in order to preserve battery life
Click to expand...
Click to collapse
Totally true on all counts. You can really use ANY usb charger to charge your Arc, but the higher the mA the faster it will charge. And the higher the mA, the less overall life your battery will have. If it's normally supposed to be good for 5000 recharges, it might drop to 4000 recharges (just numbers pulled out of thin air).
The "Normal" standard for USB power is 0.5A (or 500mA). The iPad for example uses 1.0A, or twice as much as standard. Now in the iPad's case, it refuses to charge with anything less. I don't know if that's true for the Arc or not...if so, and the SE charger is rated at 850mA, then that's probably as low as you'd want to go just to be on the safe side.
Personally, I'm willing to use the iPad's charger and charge a bit faster for a bit lower useful battery lifetime. A new battery I can buy....time spent waiting for my phone to be charged I can't get back
The amperage rating on a charger defines the maximum current the charger is capable of supplying. A 1A charger doesnt force 1A down the throat of whatever's connected to it, if you connect something can only manage to pull a maximum of 500mA then it will only get 500mA.
Consumer power supplies are generally constant voltage. E.g. a 5V charger will supply 5V to anything connected to it. The amount of current that the device will draw at 5V is the amount it was designed to draw, up to the limit that the charger can supply. If the charger cant supply enough, generally you just get slower charging (though some poorly designed devices will just refuse to charge at all). What *will* tend to destroy your device quickly is a voltage mismatch, e.g. connecting a 5V phone to a 12V charger.
You can get constant current power supplies. These ramp up the voltage in order to force the required current out regardless of what's attached to it (even if that's a human being). They are scary.
daveybaby said:
The amperage rating on a charger defines the maximum current the charger is capable of supplying. A 1A charger doesnt force 1A down the throat of whatever's connected to it, if you connect something can only manage to pull a maximum of 500mA then it will only get 500mA.
Click to expand...
Click to collapse
Exactelly what I was thinking, thanks.
Now I think I can charge my Arc with 1A without any problem, since it's gonna take only 850 mA from it
just wondering if it's safe to use my hp touchpad charger on the gio
Wall AC to USB power adapter, which has input specifications of 100-240 Volt 50–60 Hz 0.4 Amp AC, and output specifications of 5.3 Volt 2.0 Amp DC. It is cylindrical roughly the size of a "D" battery with a foldable 2-prong AC connector and Standard-A USB socket on its two ends.
Click to expand...
Click to collapse
pretty high amperage, is it safe to charge with it? done it twice already
Standard charger have 5V output and 0,7A out. I do not recommend the use of higher voltages and currents, can lead to overcharging and thus the explosion.
The internal "censor" of the cell can and wil be fried wen you continue.
0.7 vs 2.0 is about 3 times faster, truth but also a bigger ammount in a shorter time.
If the cell not capable for that, it wil overheat and at worst case it wil blow up in your face...................
And take a second gues, those are not the most expensive celles.............
I just picked up a Nexus 7 and was wondering if I can just use that 2A charger.
No.
You can go under but not over. You risk damaging the phone's charging circuit.
GldRush98 said:
No.
You can go under but not over. You risk damaging the phone's charging circuit.
Click to expand...
Click to collapse
Ummm. To the first response....your thinking of voltage not charging amperage. I might be wrong but I believe how much current your phone draws when charging is determined by the phone itself, not the charger. What you really want to watch for is a mismatch between the charger output voltage and phone input voltage, that's when the damage occurs
butikofer08 said:
Ummm. To the first response....your thinking of voltage not charging amperage. I might be wrong but I believe how much current your phone draws when charging is determined by the phone itself, not the charger. What you really want to watch for is a mismatch between the charger output voltage and phone input voltage, that's when the damage occurs
Click to expand...
Click to collapse
Your correct. The most it will draw at 5 volts is 1 amp. The best charger is the one that the phone comes with. If you want to learn more research ohms law and resistance balancing. Something like thevenin an mct.
tracerit said:
I just picked up a Nexus 7 and was wondering if I can just use that 2A charger.
Click to expand...
Click to collapse
Yes.
The Nexus7 charger will be just fine charging the Galaxy Nexus. It will not damage it at all. I use a Kindle Fire charger to charge my GNexus. It can provide up to 1.8 amps at a nice steady 5Volts, but it doesn't have to provide that many amps to charge the Nexus - so it doesn't.
Its the voltage, not the maximum amp capacity, that is critical, cannot be too high.
It is usually OK to use a too low amp capacity charger as well, the charging just takes longer. Usually...some chargers are designed poorly. When asked for more amps at 5V than they are designed to provide they could fail by just providing less amps than asked for at 5V, which would be fine but slow. What else could happen is that the voltage provided could start to vary. It could start to take on the characteristics of the AC current it is supposed to be converting to 5V DC. This can hurt your phone.
Moral of the story....the chargers that advertise half the charge time because they offer double the amperage are a scam/false. Just because they can provide up to that amperage doesn't matter, the device determines the actual current being pulled (I.e.--charging time)
i.Sound Portable Charger
Has 16,000 mah
Input: 12V 1A
Output: '5V 2.1A on each connector 2.5 A together'
I charge a number of things on here...
A friend has me a bit confused saying this could damage the charging mechanisms of the phone.
Any input please?
Thanks
rockky said:
i.Sound Portable Charger
Has 16,000 mah
Input: 12V 1A
Output: '5V 2.1A on each connector 2.5 A together'
I charge a number of things on here...
A friend has me a bit confused saying this could damage the charging mechanisms of the phone.
Any input please?
Thanks
Click to expand...
Click to collapse
Do u mean, you are giving the Galaxy Note an input of 5V, 2.1A (ie, output of Portable Charger)? if so, it is going to effect the battery life in long run..it may charge your phone faster, but definitely going to hurt the life of the battery..there are a lot of factors which should be considered like how much extra current you can give, temperature etc etc..
I don't think so: charging current is controlled by the device being charged, not the charger.
The Note will draw only ~700mA on an "AC" charger, even if that charger can supply up to 1A, 2A, etc.
On USB, it will draw ~500mA.
A mains/AC charger shorts the 2 data pins, which tells the phone that it's a dumb charger, not a USB host, and it is safe for the device to draw up to its own maximum (700mA for the Note).
---------- Post added at 12:23 AM ---------- Previous post was at 12:16 AM ----------
The corollary to that is that you shouldn't be able to shorten battery life by over-current charging: even with a 2A Nexus charger the Note draws only up to its maximum 700mA.
[I did just that test a moment ago to check: 725mA, on the 2A Nexus 7 charger]
Of course, 700mA is more than the 500mA it will draw from a USB host, so if you were really concerned, you could use that.
But the device ships with a mains/AC charger from which it will draw 700mA, so you're never going to exceed the "official" charger, whatever charging source you use.
cdmackay said:
I don't think so: charging current is controlled by the device being charged, not the charger.
The Note will draw only ~700mA on an "AC" charger, even if that charger can supply up to 1A, 2A, etc.
On USB, it will draw ~500mA.
A mains/AC charger shorts the 2 data pins, which tells the phone that it's a dumb charger, not a USB host, and it is safe for the device to draw up to its own maximum (700mA for the Note).
---------- Post added at 12:23 AM ---------- Previous post was at 12:16 AM ----------
The corollary to that is that you shouldn't be able to shorten battery life by over-current charging: even with a 2A Nexus charger the Note draws only up to its maximum 700mA.
[I did just that test a moment ago to check: 725mA, on the 2A Nexus 7 charger]
Of course, 700mA is more than the 500mA it will draw from a USB host, so if you were really concerned, you could use that.
But the device ships with a mains/AC charger from which it will draw 700mA, so you're never going to exceed the "official" charger, whatever charging source you use.
Click to expand...
Click to collapse
yes, though AFAIK the Note will draw more than 700mA from the OEM charger
and I have noticed charging speed differences by using different aftermarket chargers... never put a multimeter to them though
while charging the battery in the note is safe, I don't recommend plugging in your portable charger into a external battery charger. They may not protect the battery from overcurrent. Pay attention to all the specifications of all charging devices you use. Especially if you also have an aftermarket battery.
Cheers
Sent from my GT-N7000
guitarplayerone said:
yes, though AFAIK the Note will draw more than 700mA from the OEM charger
Click to expand...
Click to collapse
Are you sure? I didn't think that was the case; I could be wrong of course.
do you have any more details on that, please?
I have used many, many USB chargers: mains/AC, 12V, solar, portable battery, and never seen greater than ~700mA being drawn by the Note.
I'd like to know otherwise, for the odd occasion when i might want a really quick charge!
My friends point was that the i-sound charger would hurt not so much the battery but might damage the charging circuitry in the phone...course I learn this after buying this charger! ( I know its fine for nexus 7 and 10.1 tab).
Again its
Input: 12V 1A
Output: '5V 2.1A on each connector 2.5 A together'
rockky said:
My friends point was that the i-sound charger would hurt not so much the battery but might charging circuitry in the phone...course Ilearn this after buying this charger! ( I know its fine for nexus 7 and 10.1 tab).
Again its
Input: 12V 1A
Output: '5V 2.1A on each connector 2.5 A together'
Click to expand...
Click to collapse
Yup, and I believe the answer is no: you cannot damage the Note's charging circuit by using a charger that has a higher *maximum* current, since the Note will only draw a current of (approx) 700mA regardless of the charger's maximum.
As an example of that, my test showing that the Note still only draws 725mA when connect to the Nexus 7 charger, which has a maximum charging current of 2A.
Thanks
cdmackay said:
Yup, and I believe the answer is no: you cannot damage the Note's charging circuit by using a charger that has a higher *maximum* current, since the Note will only draw a current of (approx) 700mA regardless of the charger's maximum.
As an example of that, my test showing that the Note still only draws 725mA when connect to the Nexus 7 charger, which has a maximum charging current of 2A.
Click to expand...
Click to collapse
There was a mid on this site a really long time ago showing how shorting a specific connection in the usb cable will enable ac mode and this is supposedly what the oem charger does
guitarplayerone said:
There was a mid on this site a really long time ago showing how shorting a specific connection in the usb cable will enable ac mode and this is supposedly what the oem charger does
Click to expand...
Click to collapse
yup, that's right: shorting the two data pins --- which most "dumb-charger spec" capable chargers do --- tells the Note that it's OK to pull its maximum ~700mA. But it won't pull any more than that even if it's a 2A charger.
Without that short, the Note will only pull the regular ~500mA (again, regardless of charger max current): it thinks it is connected to a standard USB host, which might not be able to supply > 500mA, e.g. a laptop motherboard.
If you have a >500mA charger that *doesn't* follow the dumb-charger spec, i.e. it doesn't short the data pins, e.g. possibly a Mac USB charger, then you can get a charge-only no-data USB cable, that has the data pins shorted internally (in the cable itself), which will achieve the same effect. This is the mod you describe above.
You probably should not use that cable with a regular USB host (although the host will probably just limit its current anyway).
[Macs use some proprietary "signalling" method, whereby differing value resistors are placed across the data pins, telling the device differing levels of current to pull, etc. This is why you'll see external battery packs like Anker Astro 3 having a "Samsung port" and also a "iPad port"; madness]
Finally, some Android kernels have a hack that will allow AC mode (e.g. 700mA on the Note) regardless of the data pins. But this isn't always wise, and so many devs won't touch it. It prob wouldn't bother the Note, but it might not be good for the host/charger.
Apologies for rambling on, but people seem to ask this sort of thing a lot...
yep people wantblong battery life and fast charge.
About time a proper fuel cell is introduced
Sent from my GT-N7000 using Tapatalk 2
Most of this is over my head
So bottom line: charging my note with the i-Sound charger described in the OP will NOT damage my new Note , correct?
Tnx
rockky said:
Most of this is over my head
So bottom line: charging my note with the i-Sound charger described in the OP will NOT damage my new Note , correct?
Tnx
Click to expand...
Click to collapse
I believe that's correct; I would not hesitate to use it.
As someone else stated, however: whilst charging in the phone should be safe, since the phone controls the current, taking the battery out and charging it in a standalone battery charger may not be safe.
rockky said:
Most of this is over my head
So bottom line: charging my note with the i-Sound charger described in the OP will NOT damage my new Note , correct?
Tnx
Click to expand...
Click to collapse
Yes, that's correct. Generally, just make sure the voltage is not too high (or too low). The range of 4.7V to 5V should be OK, since there is some allowance for variations. The current ( ie, the Amperes) only indicates the current the charger is capable of supplying. It doesn't mean the charger will force all that current down the battery's throat. The device/battery will draw as much as it needs, and this will not damage the device or battery whether it's 0.5A or 2A.