Related
Not sure if this is an issue, or if its standard. But here is what im facing.
A charge off the wall will get my Tmobile SGS2 to a full charge (from around 15%-20%) with the stock plug and cable in about an hour to an hour and a half. However charging from my laptop or from a car charger im only getting a total increase in battery 15% in an hour. I tried to use the stock cable with the laptop and got about 25% in an hour and a half. I tried to use the stock cable in my car and only got 7% in 45 minutes.
Anyone have any ideas?
When charging from the car or from a laptop, the power is limited to what the cable/charger can supply which might not be sufficient for the SGS2. For the car charger, you can try buying one that supplies more amps, but for the laptop, theres really nothing you can do, as it is limited by the USB cable itself.
Do you mean the USB cable or do you mean the actual plug & internal workings of the laptop? because i have tried several cables. And just also remembered that i tried the stock cable as well with crappy results.
you can buy a 2A charger, and it will charge a lot faster, that's what i use in my car
at home or office, i just use the regular charger, as i always carry extra battery packs
When you plug it into the laptop it only gives out a limited amount of amps unlike the regular charger that came with the phone. The one that came with the phone regulates the charge so that it doesn't overcharge your device or anything. The laptop USB plug is supposed to be meant for peripherals like a mouse and stuff so it doesnt give out that much amps, therefore charging slower than a regular charger.
I use the t-mobile rapid car charger, It can charge this beast in about 45 minutes. It also has a 2nd port for a 2nd device.
Deebo took your bike too?
Really?! I've never seen my charging current go over 700 mA, even with a 2 amp charger.
I'd happily give up some long-term lifetime for faster charging.
Sent from my Galaxy S II using Tapatalk.
They have a home charger too that's a home charger plus car charger in 1. I use them in the cars but they're great for trips cause you have a 2 in 1 charger.
With 3 batteries and a external charger though, I never need a home charger and haven't even put this on a charger yet.
Just as most of the others have said here, the charge is going to be limited to what the source can put out. If you get another charger (2A charger) then it will be able to charger faster but you also want to be careful with using after market chargers there are some that can negatively affect your battery by overcharging which is when the phone gets fully charged but the charger does not ever stop with the flow of power to the device.
Ok Thanks all.
Guess i need a new car charger and something for the office.
Also did some crawling through "Mother of all battery life" thread found some good ideas there for making this thing last longer on the charge its got.
Im having the same problem my fone takes forever to charge...im pluged into the wall using the charger in the box n it took me no joke 7 hours to charge my fone!
Im on it rite now as its plugged i to the wall n im losing power instead of charging...i tested the voltage n its fine ...is tgere anythin i can do?
Sent from my SGH-T989 using XDA Premium App
I, myself, actually haven't used the OEM charger that came with the phone. Although I did notice it is quite small and the phone battery is a 1850mAh (larger than normal) that might affect the charging rate. I am currently using the old HTC charger that came with my Sensation and it charges fully in about 2 hours. If you want a charger that charges your phone in an hour and a half, I recommend going into a T-mobile store and grabbing the Wallcharger they sell. It charges 33% faster than OEM chargers and does not harm your device nor kill your batteries.
You can find it by clicking here
Exactly same problem as OP.
OEM wall charger charges phone to full in couple of hours but laptop USB or car USB is doing at 10% / hour assuming you don't do anything on your phone but just leave it there to be charged. Otherwise you'll be losing battery rather than being charged.
513263337 said:
Exactly same problem as OP.
OEM wall charger charges phone to full in couple of hours but laptop USB or car USB is doing at 10% / hour assuming you don't do anything on your phone but just leave it there to be charged. Otherwise you'll be losing battery rather than being charged.
Click to expand...
Click to collapse
As explained in previous post, this is due to limitations in the laptop USB drive and depending on what car charger you have, the phone might suck up more juice than it is able to provide.
so this is nothing a kernel or any other tweak can fix?
mightymike889 said:
so this is nothing a kernel or any other tweak can fix?
Click to expand...
Click to collapse
no a new kernel or any other tweak wont work.
So i gotta buy a new charger!?!
Sent from my SGH-T989 using XDA Premium App
Yes, or if you have like an old microUSB charger from HTC or another Samsung phone (Samsung Vibrant) you can try using those.
the 2A chargers from BlackBerry are the best
So, you guys are seeing the phone draw over 700 mA (when the charger is capable)?
If I use my iPad charger (2A), I still top out at 700 mA, and the ~4 hours that go with it. :/
Even my 1A car charger tops out at 700 mA, that's why I thought it was a hardware issue.
Sent from my Galaxy S II using Tapatalk.
Hi guys
Im having a weird problem with the battery. It seems battery doesnt charge when im using the phone although it says and shows it charging! It just stays at the same battery percentage it doesnt charge or drain! When i turn off the screen it charges the battery just fine. I called o2 UK where i bought the phone, the rep said when i use the phone it consumes more power than it gets. Can this be true?! Do you think its just a software bug or defective hardware or defective battery?
Sent from my Galaxy Nexus
This is true if you're charging from the USB on your computer. USB ports only provide 500mA. The phone seems to use more than this if you are actively using it. I recommend using a wall plug that provides at last 1 Amp (1000ma) to effectively charge the phone.
How about car chargers? Same thing happens when its charging with the car charger..
Sent from my Galaxy Nexus
If I'm not mistaken, any car charger, whether it's rated at .5A, 1A, or 2.1A is only going to provide .5A to your phone using a typical USB cable. The USB cable that came with your phone has +/- lines for power as well as 2 data lines. If you pickup a "charging only USB cable" it has the data lines shorted so that only the power lines are functional. This type of cable would allow you to take advantage of the higher current 1A and 2.1A chargers - I think anyway. I'm still new to Nexus so I haven't confirmed that, but that's the way it worked on my old phone. I did read somewhere that even with a charging only cable someone wasn't able to pull 1A from their car charger so I don't know if that was a unique issue or if the Nexus doesn't behave the same way. My understanding is the amount of current pulled from the charger is dependent on the charger AND the phone. Using a special charging cable tricks the phone into thinking it's on A/C I guess.
I was watching the Mavericks vs Thunder game using the watch ESPN app and my nexus battery was at about 93%
I watch since halftime to the end of the game and I was plugged in to a car charger the whole time and when the game ended about 1 1/2 hrs later the battery had dropped to 53%. Can't understand it. Hope someone here can explain this to me.
Phone is galaxy nexus, obviously, the battery is the 2100 OEM battery from Verizon store, charger is a belkin dual outlet 1amp micro car charger with the cable that came with a Droid charge.
Thanks in advance ladies and gentlemen, I did look and search, didn't fins anything covering this specific issue.
Sent from my Galaxy Nexus using xda premium
i am 99% sure its the car charger. but cant give u a reason
rfvreynoso said:
Phone is galaxy nexus, obviously, the battery is the 2100 OEM battery from Verizon store, charger is a belkin dual outlet 1amp micro car charger with the cable that came with a Droid charge.
Click to expand...
Click to collapse
5V right? that's not a huge draw at all on your battery, i'm assuming your car was either running or started right up afterwards...you can be certain your phone was getting that full 1A especially if your car was running. if your phone showed charging and your phone will normally charge from your car like that then you shouldve been in good shape. despite what you may think, i actually am trying to present relevant info lol but ummm other than that? i would definitely try a multimeter (.....if you have one.....) cuz that would show you exactly what you're getting in/out. usb pinouts should be somewhere on the internet. other than that, try doing the same thing (except for maybe a shorter time period if preferred) on a wall charger which should be more reliable and compare results. i've had devices that burn power faster than they receive them....but the good ole gnex? im not so sure. (engineer here).
I just recently join big red and coming from sprint with an evo 4g and didnt have this issue with that phone and same charger. I'm definitely going to try it with home charger to see if its the charger.
Extra info, the vehicle was powered on before I plugged in the charger, in case it matters any.
Thanks to all the reply thus far.
Sent from my Galaxy Nexus using xda premium
I find that under heavy usage, only the plug in wall charger gives enough juice to keep it increasing... and even that can go flat or decrease if you are really pushing it... also the way the battery stats are displayed can be flaky too... jumps in the level of charge and quick drops... hard to tell how accurate the reading is.
I hear you. That's crazy, basically the phone draws more power that the charger can provide. I would think the charger should be fine since its 1 amp just like the home charger.
Sent from my Galaxy Nexus using xda premium
Check in settings - status if it says charging (ac) or charging (usb) when plugged in you car.
If it says charging (usb) the charge amps are limited to 500mA.
Sent from my Galaxy Nexus using Tapatalk
The phone can use more power than a car charger can supply. This is commonly posted all over. Check your car charger, its likely a 0.5 amp. Buy a 1 amp or higher.
rfvreynoso said:
Phone is galaxy nexus, obviously, the battery is the 2100 OEM battery from Verizon store, charger is a belkin dual outlet 1amp micro car charger with the cable that came with a Droid charge.
Click to expand...
Click to collapse
Your problem is the charger, 1 amp is the sum of the two outlets, hence you're only giving your phone 500mA max. When charging at that low of a rate, you'll drain the battery when doing anything power intensive on the phone. Your only remedies for this is to get a car charger that's capable of putting out 1 amp or more on a single line. What I personally did was get the Griffin Powerjolt dual charger for $8 on Amazon, opened it up, and soldered the center data pins on each port together.
najaboy said:
Your problem is the charger, 1 amp is the sum of the two outlets, hence you're only giving your phone 500mA max. When charging at that low of a rate, you'll drain the battery when doing anything power intensive on the phone. Your only remedies for this is to get a car charger that's capable of putting out 1 amp or more on a single line. What I personally did was get the Griffin Powerjolt dual charger for $8 on Amazon, opened it up, and soldered the center data pins on each port together.
Click to expand...
Click to collapse
I though that the griffin powerjolt dual outlet charger would dish out 1amp on a single port if the 2nd port was not being used. Interesting, I can see your point. Would you happen to have a picture of, or remember which are the two that need to be bridge inside to make it a full 1amp output?
Thanks in advance.
Sent from my PC36100 using xda premium
Herman76 said:
Check in settings - status if it says charging (ac) or charging (usb) when plugged in you car.
If it says charging (usb) the charge amps are limited to 500mA.
Sent from my Galaxy Nexus using Tapatalk
Click to expand...
Click to collapse
Okay, I tried what you said and I got weird results. I used the awkward griffin powerjolt dual outlet car charger. I tried using two different cables, one was from my girl's Droid charge and when I plugged it in and check the status it said usb charging, then I plugged in a cable that came with a i go green adapter that I had purchased at an airport and the phone said ac charging. Unless the cable that came with the Droid charge can only pass 500mamp, I'm puzzle.
Both were plugged in at same time and also both cables were tried by themselves in each outlet of the griffin charger by themselves.
Interesting huh. I will keep testing and see what gives, last resort I get a more powerful car charger. Will keep you guys posted, thanks to everyone that contributed and pitch in thus far.
Sent from my PC36100 using xda premium
Got an update on this issue. I streamed another 45 mins to 1 hr of ESPN using watch ESPN app and the results are even more interesting. I was using the wall charger that came with the Droid charge and the USB cable that came with the I go green wall adapter that I have purchased at an airport a while back. Here is what happened, when I started streaming the battery was at 94% and I plugged in phone to charger and under settings/about/status it showed AC charging. After 45 mins to 1 hr of streaming the phone was extremely Hot towards the center of the back and below the cam lenses and led light. Also the battery had dropped to 93% and the phone status showed not charging, even though the battery icon on home screen next to clock shows the lightning symbol inside the battery like is charging.
I don't understand what is happening. Grrrrrr. This is using a wall a charger for a droid charge. Now of to trying it with the OEM charger and cable.
rfvreynoso said:
Got an update on this issue. I streamed another 45 mins to 1 hr of ESPN using watch ESPN app and the results are even more interesting. I was using the wall charger that came with the Droid charge and the USB cable that came with the I go green wall adapter that I have purchased at an airport a while back. Here is what happened, when I started streaming the battery was at 94% and I plugged in phone to charger and under settings/about/status it showed AC charging. After 45 mins to 1 hr of streaming the phone was extremely Hot towards the center of the back and below the cam lenses and led light. Also the battery had dropped to 93% and the phone status showed not charging, even though the battery icon on home screen next to clock shows the lightning symbol inside the battery like is charging.
I don't understand what is happening. Grrrrrr. This is using a wall a charger for a droid charge. Now of to trying it with the OEM charger and cable.
Click to expand...
Click to collapse
The battery can stop charging if it gets too hot (safety measure).
Sent from my Galaxy Nexus using Tapatalk
Herman76 said:
The battery can stop charging if it gets too hot (safety measure).
Sent from my Galaxy Nexus using Tapatalk
Click to expand...
Click to collapse
Exactly, in the driver i think the overheat is set to 140F. Also when your charger showed as usb it only gets 509mA and when showing ac it gets the full 1 amp. So just pay attention next time and see if it drains when showing ac.
My car charger is a 1.3 amp and always shows as ac and never drains while charging.
Herman76 said:
The battery can stop charging if it gets too hot (safety measure).
Sent from my Galaxy Nexus using Tapatalk
Click to expand...
Click to collapse
I though about that but then I was wondering, shouldn't the wall charger provide enough power to run everything in there while charging the battery or even without the battery in the phone. Like shouldn't the battery hold the charge that it already has when I started streaming as long as the charger is 1amp?
I would not care if when I stream the phone battery would just hold its charge at what it has at the moment even if it does not charge while streaming. Hopefully that is clear to understand.
To all the fellow galaxy nexus owners out there, maybe you all can test on your phones and see if you get same results as me. Download watch espn and stream the channel for 30 mins, notice what is your battery level before you start streaming, of course plug the phone to a car charger or wall charger and see if battery remains the same, drops charge, or gain charge at the end of 30 mins, or maybe an hour. I am not asking you to watch it for the 30 mins or 1 hour, just let it run and see what happen, if you can of course. only reason why I ask for watch espn is because it is the app that I have been using to stream nba games for the last few days.
Another thing since I am already here with this streaming issue, I have an original SlingBox, the cheapest of the cheapest when they first came out, just coax and that is it. I would like to know if I pay the $29.99 for the app from the market when i switch roms on my galaxy nexus would I lose the app? I have already unlocked and rooted my galaxy nexus and lets say I buy the app and I am running cm9 when I purchase it, if I change to gummy rom or back to a stock rom while still rooted would I have to re-buy the app ?
Thanks in advance for all the input.
Have u tried underclocking cpu with setcpu app?
Sent from my PG06100 using XDA App
King Jeriamas said:
Have u tried underclocking cpu with setcpu app?
Sent from my PG06100 using XDA App
Click to expand...
Click to collapse
No I haven't try that. I am currently testing out roms like a mad man trying to find the best for my liking. Question for ya, As far as I know that is kernel dependent right? Like the kernel has to support it, if so which kernels do support it and what would be good underclocking settings ?
I get similar results while using navigation and pandora at the same time, the phone uses more juice than the car charger can provide.
Ironically I plugged in the oem charger and oem cable from the galaxy nexus box and open it (didn't really wanyed to do that) and streamed 30 mins of espn on watch espn and battery was at 70% when I started after 30 mins streaming it had actually climb to 78%. Confused yet everyone? What gives?
Sent from my PC36100 using xda premium
Not all that odd. Using my Fascinate charger (0.7 amp) I get noticeably slower charge times than the OEM charger (1 amp). I don't use my phone much while I'm charging so I can't provide any feedback for that.
What is the Droid Charge charger rated at?
Hi!
All owners of Kidigi car dock should read and do this!
I got a Kidigi car dock with charger. The first thing I tried was putting the phone on the included charger - and indeed, it did charge in "AC mode" (aka 1000mA max).
Then I installed the cradle, connected the charger to the cradle and started using it.
But after 2 days I noticed it doesn't really charge when navigating or recording - and it was not an overheat issue. So today I looked again and it was charging in USB mode!
Apparently, the good folks at Kidigi screwed up the connection inside the dock (probably to trigger Car mode and forgot to connect it all).
The fix:
1) unscrew the four visible screws on the back of the dock (not the 4 center ones)
2) unscrew the fifth screw under the label on top
3) unscrew the phillips screw that holds the connector
4) short PINs on the phone side labelled D- and D+ (I just used a blob of solder)
5) that's it
Now it triggers Car mode AND charges in AC.
This fix is essential for anybody using this dock, and I'll be mailing Kidigi shortly to let them know they screwed up...
mine charges mine fine whilst using GPS and Bluetooth.
Not a quick charge tho but it definitely charges more than discharges if that makes sense .
I will check the pins tho thanks =)
+
I hope this wasn't on purpose for the sake of overheating?
Sent from my cm_tenderloin using xda premium
colemanuk said:
mine charges mine fine whilst using GPS and Bluetooth.
Not a quick charge tho but it definitely charges more than discharges if that makes sense .
I will check the pins tho thanks =)
+
I hope this wasn't on purpose for the sake of overheating?
Sent from my cm_tenderloin using xda premium
Click to expand...
Click to collapse
It doesn't overheat from charging, but from using it (Navigation, recording, video...). AC charging does no harm in this respect (nor does it help).
You'll notice it when something is running and the brightness is on full - USB charging will not feed the phone and it will start to discharge.
So is this a problem at the charger end if so I have a belkin 1amp charger I can use.
I understand the data pins have to be shorted for it to see the AC mode.
In my power menu both the chargers I have say AC whether plugged in through the dock
or just to the cable and charger without the dock.
surely this means its OK or would show usb am I wrong?
I've opened the dock and can't see for the life of me the name on the pins +
my soldering skills are a bit much to be desired when working this small
Sent from my cm_tenderloin using xda premium
colemanuk said:
So is this a problem at the charger end if so I have a belkin 1amp charger I can use.
I understand the data pins have to be shorted for it to see the AC mode.
In my power menu both the chargers I have say AC whether plugged in through the dock
or just to the cable and charger without the dock.surely this means its OK or would show DC am I wrong?
I've opened the dock and can't see for the life of me the name on the pins +
my soldering skills are a bit much to be desired when working this small
Sent from my cm_tenderloin using xda premium
Click to expand...
Click to collapse
No, the problem is inside the cradle itself - even though pins on your charger are shorted, they are not even connected through the cradle connector. You have to short them at the cradle connector.
Btw all chargers will work as AC then
Strange that it shows AC for you, are you sure it's right? Can you make a photo of the connector? Maybe you got a different revision or something...
zvieratko said:
No, the problem is inside the cradle itself - even though pins on your charger are shorted, they are not even connected through the cradle connector. You have to short them at the cradle connector.
Btw all chargers will work as AC then
Strange that it shows AC for you, are you sure it's right? Can you make a photo of the connector? Maybe you got a different revision or something...
Click to expand...
Click to collapse
Yes it definately shows AC for both my chargers whether plugged through the cradle or not.
Does yours show USB or something? Like I said mine does charge all be it very slowly when using copilot.
Is the writing for the pins obvious for you as I swear I have none
Sent from my cm_tenderloin using xda premium
I'll be damned!
Plug phone in dock then plug in charger (shows AC!)
Plug charger in FIRST then put phone in dock shows USB!
In the instructions they say to do it the first way I think.
I wonder if it is charging AC then hmmmmmm?
Sent from my cm_tenderloin using xda premium
I got mine today and found it was charging in AC when I tried either way!
optiknerv said:
I got mine today and found it was charging in AC when I tried either way!
Click to expand...
Click to collapse
WTH maybe some of you got an updated version
zvieratko said:
WTH maybe some of you got an updated version
Click to expand...
Click to collapse
Gonna go get dressed ( I'm having a lazy morning ) and i will double check but I swear its fine
EDIT : Confirmed mine is fine. I checked with the bundled charger cable as well as my own and whether the plug is in before the HOX is in the cradle or after, power settings shows "Charging AC" in all cases. I haven't seen USB charging at all with the cradle. They must have realised their mistake and fixed it.
Today the car dock Kidigi arrived.
When connecting the phone, I noticed that there is recharged via USB.
Through this tip, Is now loaded by AC ....!
BIG [email protected] zvieratko.
(Sorry for my bad English)
Seems I'm the only one with a working dock out the box!!
Mine is aslo writing AC charge, but it is definitelly not AC charge. Going to fix it
I'm definitely curious how mine is going to work.
Ordered mine last week through ebay, so I hope it's a late build without the problem.
'Cause I don't have a blob or solder or whatever can fix this thing...
Hi guys,
I recently bought one of these Kidigi car mounts for my HTX One X and have found that the battery will slowly drain (about 1% every 10 mins) when I have it docked and am using sat nav (Google Nav or Co-Pilot). My battery app says that the phone is charging (estimates about 6 hours to charge 30%).
I've checked the charging method and it shows that it's charging via AC (not USB).
I've tried a few things like running Co-Pilot in power saving mode, dimming the screen, closing down all over background apps, but my battery still slowly drains.
Do you think this soldering fix might help?
Thanks all.
AC or USB changing
Hi, i've brought various chargers off ebay and other sources and even when the phone reports AC charging i've had leads that use wire so thin that the phone cant get the high current charging to work.
Check that your adapter is providing more than 500 mA. Certainly I've had no trouble with it charging the phone while navigating.
I have a question regarding this mod. I bought this charger and am fixing to recenter the microusb port to properly mate with otterbox commuter case still on. The OP states to just short the 2 data pins together, but I'm wondering if I should do this with a resistor to load balance the lines or if that is even necessary?
Hello everybody,
I have recently bought the Griffin Dual USB car charger.
I use quite often a GPS navigator when I am driving, so I wanted to buy a car charger which was powerful enough to sustain gps and 3g data plus a little extra juice to charge my phone battery. I found this charger on the internet and the specifications say it's got an output of 1A which should be more than enough for my needs. However, I was quite surprised when I realised that the battery still goes down really slowly when I use the gps app.
I've had a look online and apparently most car chargers are not recognised by your phone as a proper charger. For this reason, they provide only 500mA. You can double check this by having a look at 'settings > about device > Status > Battery status'. If it says 'Charging (USB)', it provides 500mA. Instead, if it says 'Charging (AC)', it provides more (so called fast charging). Well, my phone says Charging (AC). But it's still not enough apparently
Do you guys know any app or anything I can do to test how much the charger is actually providing?
As you can imagine, this is quite annoying.
Thanks
i'm in the same boat as you but a different dual USB Charger
It's suppose to output 2.1A + 1A or something along those lines and it does charge last generation iPad and an iPad Mini at the same time without an issue.
When I plug a Galaxy Nexus in it charges as a USB BUT when I plug the Galaxy S3 it charges as AC but a 2 hour trip only got my phone battery up to 47% which is way way too slow and that is without GPS
The AC charger that came with my phone only outputs 1A but it charges my phone in 2.5 hours from dead flat to full
My car charger is the same. 2.1A port for tablets and stuff. 1A port for everything else. I have noticed that if I plug my s3 in the 2.1A port, it charges slightly faster. However, it's not even close to my 1A wall charger.
Sent from my GT-I9300 using xda app-developers app
Any idea at all?
Thanks
Sent from my GT-I9300 using xda app-developers app
http://www.youtube.com/watch?v=jzoMhKFiOB0
I don't know if this will help. have a look at the comments as well.
Dual Usb Car Charger
Valdagor said:
Hello everybody,
I have recently bought the Griffin Dual USB car charger.
I use quite often a GPS navigator when I am driving, so I wanted to buy a car charger which was powerful enough to sustain gps and 3g data plus a little extra juice to charge my phone battery. I found this charger on the internet and the specifications say it's got an output of 1A which should be more than enough for my needs. However, I was quite surprised when I realised that the battery still goes down really slowly when I use the gps app.
I've had a look online and apparently most car chargers are not recognised by your phone as a proper charger. For this reason, they provide only 500mA. You can double check this by having a look at 'settings > about device > Status > Battery status'. If it says 'Charging (USB)', it provides 500mA. Instead, if it says 'Charging (AC)', it provides more (so called fast charging). Well, my phone says Charging (AC). But it's still not enough apparently
Do you guys know any app or anything I can do to test how much the charger is actually providing?
As you can imagine, this is quite annoying.
Thanks
Click to expand...
Click to collapse
Hi, if you are looking for a best usb car charger for your device then i have a option for you. Please check my profile and fo to the link in my bio.. Thank you
I recall back with my old phone (Virgin Mobile LG Optimus V), the lead devs teamed up and made a flashable patch that allowed you to toggle fast charging on and off, basically telling the phone whether it should consider the power source a USB or Wall charger and it worked good. Maybe we can get some people to team up and build that for the S3?