Sprint store replaced my screen. - EVO 4G Q&A, Help & Troubleshooting

I am pretty new here and have loves the source of all things EVO!
I flashed my first rom, broke the screen two days later, and reflashed it to stock so sprint would fix it. They replaced the front half of the phone. The glass, LCD, digitizer, bezel, and buttons. Here is my question: Now when i press firmly on the glass the LCD distorts like a computer monitor. It only happens when I press pretty hard while putting on my 3 layer case as one piece, so I am pressing pretty hard. I know thats probably how I wrecked the first screen, so I've stopped that. However I do not remember the origional screen doing that. Is sprint using lower grade glass screens?? Has anyone else noticed this?

Related

Broken LCD Screen, replaced it, now touch doesn't work

OK, so I dropped my phone and the LCD went out, I hooked the phone up to the laptop and the phone still works fine, even the touch screen works. ( I used My MObiler to see phone screen on the pc).
I bought a new LCD screen off of Ebay and replace it, now, the LCD screen works, but for some reason, the touch screen stopped working.
When I took the LCD apart from the touch screen, there seem to be a layer of grease of some sort between the touch screen and the LCD. I wiped it off with a lens cloth, don't know if that caused any problem.
Also there is a dark film (tinted) glued to the touch screen when looking from the back, what is that for? I looked at replacement touch screen on Ebay but none of them have the tinted film layer. I've search all over the internet for instructions but can't find any.
So my question is, what are the correct procedures for replacing the LCD screen and the touch screen (digitizer) ? Also after I installed the new LCD screen, the screen is very reflective and the glare is really bad, how do I fix that problem?
Thank you experts!!
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
bojangle said:
You should have replaced both the LCD screen and the Digitizer. There are complete kits on ebay as well as instructions/tools to complete the replacement. Did you purchase the digitizer also?
Click to expand...
Click to collapse
I went ahead and purchased the digitizer by itself after the original stopped working. Hopefully, it will get my phone back to normal. Thanks for your reply!
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
fone_fanatic said:
in the wiki theres disassebly instructions of the device that should help you (but you probably already know that since you've already switched out the LCD)
In my experience, i have never replaced either the digitizer, or the LCD by themselves, i've always bought LCD+Digitizer and replaced them as one. Seems like the Digitizer is usually glued onto the LCD and i never wanted to mess with that.
Click to expand...
Click to collapse
I should have ordered the kit instead of just the LCD. What lead me to order just the LCD is when I hooked the phone to my pc and confirmedthe digitizer still worked. And since this is the first time ever I disassemble a phone, I assumed the two things were separated.
But my digitizer should come in tomorrow so I'll just have to wait and see. Thanks for the info.
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone pad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing my in the car door as I got in....it feel out of my pocket the exact moment i was closing the door....
My screen is shot, but other than that the device appears to work. I can power on, and try to dial after I press the hard key for the phone bad. The touch portion seems to work, but from your luck, I guess I am looking at having to replace both...
anyhow...any advice on guides and how to find the stuff on the ebay would be apperciated.
I still have 18 months of a 2 yr contract....sucks....and it sucks doubly becuase i just took the insurance off last month....grr..
Click to expand...
Click to collapse
Here's a photo guide of the disassembly of a Rhodium (TP2), it might give you some insight. There's also been a number of threads in this section about hardware parts and the screen/digitizer in particular, listing places where people found/ordered replacement parts.
forcemac said:
where did you find a guide to take apart the TP2? I just had the unfortuante luck of smashing mine in the car door as I got in....it fell out of my pocket the exact moment i was closing the door....
Click to expand...
Click to collapse
The disassembly instructions are here: http://translate.google.co.uk/trans...ka/htc_touch_pro2/&sl=ru&tl=en&hl=en&ie=UTF-8
I did not follow those instructions since I did not want to open the back of the phone.
What i did was I tilted up the phone and used a very small screwdriver and unscrewed the two screws from an angle (it worked).
Then I pried the back of the tilting part of the phone all around to reveal the inside. Be careful not to pull too hard on the flat cable since it's still attached to the back (body) of the phone.
The LCD and touch screen are glued together (I didn't know that before). At this point I would remove the tape that is attaching the flat cable to the back of the LCD, and also lift up the clear yellow tape and detach the three connections.
The widest ribbon is from the LCD, the medium one is for the 4 hard buttons in the front, and the little one is for the touch screen.
I would suggest wearing some sort of anti-static wrist strap (I think I fried my touch screen along with the flat ribbon that is attached to the phone while trying to replace the LCD without anti-static wrist strap).
Once the whole tilting part is freed from the phone, I would carefully push the whole screen (digitizer + lcd) out from the frame, again, they are glued to the frame but can be removed fairly easy.
That's it, the install is reversed of removal and hopefully yours will work again.
Like I said, I think I fried my flat ribbon so after replacing the Digitizer (it came in today), the touch screen still doesn't work, so now I'm looking for that part, I'd appreciate a link to it if anybody knows where to get one.
Oh, and for the parts, just do a search on ebay for "touch pro 2 lcd" or touch pro 2 lcd + digitizer"
Gook luck with your phone!
What tape to use to stick digitizer back to inner bezel/chassis?
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
zedii.co.uk/DSC_0002.JPG
^some of that tape is left on the digitizer... it's the black spongy stuff...
zedii.co.uk/DSC_0003.JPG
^i cleaned (removed residue of sticky tape) in the inner part of the bezel where the digitizer would stick...
Any specific tape to use that anyone knows of?
zedii said:
Hi - i got as far as trying to replace my Digitizer only to find that the LCD was stuck to it too. So as clever as i am (not) - i tried to remove the LCD off the digitizer - but that just ended up cracking it.
So i'm in the process of ordering a LCD with the digitizer - pre-stuck together (i hope!) - but my question is:
When i removed the digitizer off the front bezel, there was this spongy sort of double sided tape... i assume it was used for a reason and not just any ordinary double sided tape (presumably to allow a bit of leway between the digitizer and the bezel when pressure is applied to the touch screen)...
Any thoughts on what sort of tape this is? - here's some photos of my digitizer and the bezel:
Any specific tape to use that anyone knows of?
Click to expand...
Click to collapse
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
adp9626 said:
I wish you had asked before you ordered the digitizer + LCD, since I ordered mine separately, and they seem to both working ok. The digitizer does not have to be glued to the LCD. But anyway, I just used plain old Gel superglue to glue the digitizer to the bezel. I used Gel superglue so it won't run into the electronics beneath. Things seems to work just fine now.
One thing to consider when you crack open the whole phone though. Be careful not to loose any part from within the phone, because apparently, I lost something, now my accelerometer doesn't work, and my screen doesn't rotate when you slide out the keyboard. Hope it works out for you!
Click to expand...
Click to collapse
Thanks for the advice adp9626! Well in summary I think I've just been messing about too much and being stupid really.
In the end, I managed to just remove the top part of the screen without actually having to break into the bottom section of the phone.
I was a bit concerned about the whole sticking of the LCD to the Digitizer part. I actually did purchase them separately, however I was not sure what kind of glue was used to stick them both together - as I recall it was a nightmare to try and remove the LCD off the old Digitizer.
So I returned both separate parts (got a full refund as I didn't use them) - and now I am looking to purchase both parts stuck together.
I'm waiting on the guy on eBay to confirm that they are both stuck together. I'm also thinking of using double sided sticky tape to stick the Digitizer back to the inner bezel...
So that's the final plan! I've been a bit silly in rushing with ordering parts etc. but I just want to be on the safe side now - well - at least with the LCD stuck to the Digitizer part.
I will take your advice on the gel superglue if the double sided sticky tape doesn't prove it's stickyness!
Thanks
Zayd.
Can anyone help me find the lcd screen and digitizer as a single unit for Sprint? Everyone I find states not for CDMA.
Thanks
Anyone ??? I spent an hour on google and still came up with no leads.
hyghlndr said:
Anyone ??? I spent an hour on google and still came up with no leads.
Click to expand...
Click to collapse
I ordered one from this guy and it works great. it comes with the entire top half of the phone and the keyboard. There is only one left so you may want to hurry. Link: http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&Item=270583335455&Category=20336&_trkparms=algo%3DLVI%26its%3DI%26otn%3D2
Edit: I wanted to add that they're are slightly used so there will be scratches. The one i received is a little more scratched than my original then again the scratches aren't noticeable when the back light is on and you're getting a working screen.
Just my experience, I had a faulty LCD, digitizer was OK. Bought a replacement LCD off ebay, delivered from China but only cost me £20 inc delivery. Arrived with tools as well (T5, T6, philiips, and pry tool). Followed a couple of disassembly instructions online, took me a while to get all apart but managed it. None of the instructions online go through actually taking the screen out, I thought I'd messed it up as I took the back half of the LCD off and left the front bit on, and I couldnt get it off at first. I ended up using a very sharp scalpel to slide between the LCD and digitizer and got them apart eventually, as I didnt realise that they were glued.
Anyway, I just placed the screen on, no glue as there is a ring of sticky tape around the back of the digitizer which holds the screen in. Connected everything back in the end and its working fine. Only prob is I think I damaged the power/standby button, so be careful when around this area.
Touch Screen not responding after replacement
Recently, I replaced a glass screen on a SGH-M919 Galaxy S4. Previously, during the process of cleaning the glue residues off the LCD screen; I rubbed it with rubbing alcohol and it removed a small streak of the adhesive glue off left side of LCD screen and bottom right corner. After installed the new glass screen, I noticed a few spots of the glass screen wasn't sticking onto the sticky layer. So it looked like it has big air bubble between the glass screen and LCD. And I could see the rubbed off streak on the LCD screen. Everything worked fine with the new glass screen, with the exception of seeing the streak and bottom right corner rubbed off.
A few days ago, I had a table clock fell on top of the phone and broke a piece of glass. Nothing happened to the LCD screen and still functional 100%. So I got a replacement glass screen - the same as the first time replacement. With noticing of the rubbed off streak and corner of the adhesive layer on the LCD screen - I decided to rub off all of the adhesive layer from the LCD. I sprayed some Goof Off liquid on the adhesive layer and left it over night. Next morning I continued scraping off the glue with a small plastic card. Cleaned off all glue residues and examined the LCD screen for any scratches or damage. There was none. Re-installed new glass screen - but now the touch screen does not respond to the touching on the icons. Only the Home, Menu & Back touch button work. I was baffled after this.
Could it be that because I left some the Goof Off liquid on top of the LCD screen over night and it might have leaked to the other side and shorted out something? I saw a few forums that suggested a Factory Reset. I did that - but still didn't work. Please advise on what I need to do to fix this problem.
Thank you in advance for the advise or suggestion.
So you know that these are the TP2 forums, and no one has used this thread in the last 3 years....right?
LCD digitizer replacement.. now black screen
I saw the for replacing the LCD-digitizer of my nexus 4 phone, and followed the steps carefully. After I placed the battery, I checked to see if the phone turns ON and the display is working before I complete the last step of putting the back coverplate. I successfully switched it ON, saw a perfectly working screen, and browsed through my apps. To complete the assembly, I put the back cover by gently pressing the frame along the edges, but suddenly I saw some yellow green lines in the middle of the screen. I switched it off and again switched in ON, but now the entire screen had light with no display.
To fix this, I tried again checking all connections but no luck. What could be the reason for the sudden loss of display when it worked perfectly fine moments ago? Is there a possibility that I damaged the LCD while putting the back cover on the phone?
I am also not sure about one of the ribbon connectors of the digitizer. There are 2 big ones which are prominent and has ports to connect. However, there is a little third one which also has to come through the gap but doesn’t connect anywhere. Has anyone also experienced this while replacing the screen? Any help will be appreciated.

[Q] Shattered glass

So, I shattered the glass on my Galaxy S3 today. It's pretty messed up (see the attached picture), but the touch works, even in the damaged areas. So it seems it's only the glass that needs to be replaced, with something like this:
http://www.ebay.co.uk/itm/Blue-Fron...K_Replacement_Parts_Tools&hash=item417515ee67
Correct?
Yep, goodluck. Replaced the same on my Galaxy Note 2. all good now.
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
1slow4G said:
Yeah.... if i were you and have the funds, I would replace the complete assembly ($100-$150 on ebay) and be happy.
I shattered the screen on mine and replaced the digitizer alone and now the screen has freezing/unresponsive issues. I should of known better and replaced the complete assembly, I got what i payed for, literally less than that actually. Now i have a semi-new gs3 collecting dust until i save up for a complete lcd.
Click to expand...
Click to collapse
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
MadsBen said:
The screen seems to work fine, touch/responsiveness is working fine in the areas. I have no intention of spending the £100-120 on a complete new screen (again...). I'd rather save that for a Nexus 5.
I'll post again when I receive the part and it's been replaced.
Click to expand...
Click to collapse
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Actually the glass on an s3 is just that, glass. The digitizer is fused together with the LCD. However glass is glued to the LCD which can make it very difficult to replace. If you've never taken on the repair of a screen before then I would say you'll be more likely to break the LCD than not in your replacement of the glass. But again it is possible if you are very slow and very careful. As someone else mentioned though it's much easier to replace the whole assembly.
It didn't went well. I wasn't too carefull. In the bottom, the glass was too shattered, so when I tried to lift it, a piece with glue got stock and lifted the digitizer. So now that don't work. I'm not gonna spend £100-120 on a new digitizer, I'm gonna settle for my good old Nokia 6300i (and Nexus 7...) and wait for the Nexus 5.
I would wait for the n5.. gs3 is a dying trend already.
Its hard like everyone said , if your really gunna do it watch videos online and be prepared. If you know anyone that has done it successfully ask for help or tips
ouch didnt see u tried it already
the same happened to me on my wife's white sgs3 trying to be the savior of the day turned out to be an expensive digitizer replacement of $200 instead of the $8 glass replacement. I rushed the glass removal and cracked the lcd screen. I could have ordered one on ebay for $100 but wife needs the phone the next day so i decided to get it repaired locally.
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
My 2 cents
bidibull14 said:
Just replace the glass. A lot of care for changing it, but it is not so hard to do. I did it 2 weeks ago, and all is all right.
Click to expand...
Click to collapse
Wanted to warn that changing the glass is not for everyone. It takes patience and zen. If you rush it, you will likely break LCD and spend even more $$$ that you would have otherwise. Also following notes:
1. Watch at least a couple of youtube videos before starting.
2. Heavy duty heat blower works much better than a hair dryer. Of course, don't go crazy, as it's possible to melt the phone with it
3. S III has a wire at the bottom (the one which goes to the buttons). If you damage it, you will need to replace whole LCD, there is [almost] no chance you will be able to fix this wire. So, always start removing glass starting with the top of the phone
4. Heavily cracked glass is hard to remove, as it crumbles. To make it easier, a) put a scotch tape on top of glass, so that the small pieces stick to it, and b) use a lot of heat
5. Everybody advises to use plastic tools, personally I used swiss army knife with high level of success, and never had a problem scratching LCD. Your mileage may vary, but using metal blade certainly makes life much easier, especially in heavily cracked glass situation.
6. If you do use blade, it often is enough to get blade just a little bit under a glass, and then simply apply heat. Big chunks will unglue all by themselves.
7. Remember, that failure is always an option. Don't use it on the phone, if you know that you desperately need it working right this day, if you don't have a plan B.
1slow4G said:
Mine was working fine with cracked digitizer as well. The problems started with new digitizer. Seems that when typing hard enough the digitizer touches LCD and causes to freeze up. Anyways, Good luck.
Sent from my neXus⁴ using Tapatalk 2
Click to expand...
Click to collapse
same freezing issue on mine... apparently the hardness of Gorilla2 is much greater than the knockoff glass replacements. The replacement glass on ebay and kijiji may not be authentic and that is why it bends slightly when pressed harder (in fact mine cracked completely when I applied too much pressure)
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
hani93 said:
i replaced my glass too (about month ago), and discovered that , the "freezing issue" come's when you press too hard.. that the glass touches lcd.
after quick google-ing , i've found that they suggest to apply uv glue (octa glue) , to fix that.
have somebody tried that ? is it worth that much effort to mess with liquid glue ?
Click to expand...
Click to collapse
I've heard about that glue too. I'm considering switching mine, because when I repaired I reused the glue of the original glass, and know I had dust between the glass and the lcd -.-
My concern is about the uv light, don't know if we could put in the sun to substitute it.
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
m1batt1 said:
I was researching how to replace the glass on an iPhone not too long ago and watched a video where the guy used the UV bonding agent. Long story short he said you can use sunlight to cure it but it takes substantially longer than using a UV lamp. I don't know exact time for sunlight but apparently it would work.
Also it appeared to be a long delicate process of removing the current glue from the digitizer and LCD without damaging it. But I'm sure anyone who has already replaced the glass knows how tedious the process is.
Click to expand...
Click to collapse
it's not that hard to remove factory gle there..
for example, i removed mine, by rolling the glue with fingers.
just make sure, that you don't apply too much pressure to lcd.
and after that, clean up lcd form dust/fingerprints, and you are good to go.
and for removing glass, i used usual/ stronger kitchen knife (attached picture).
i replaced my glass 3 months ago.
i use normal hair dryer to remove glass and glass comes out almost as whole except for small broken pieces.
i think my scratch guard help in that.
i didnt use any additional glue or uv light.
nonresponsive screen is issue but only when you press too hard and press of power button resolve this issue.
but whole process of replacing galss took 2hrs

[Q] Touch screen issues after replacing glass

I broke my screen a while ago, and decided recently to go ahead and change it myself. I ordered a glass for 10$ on Ebay and when it arrived, I followed a tutorial on Youtube where I had to heat the front of my phone, then with a knife or something sharp lift the glass, then put the net one after I was sure everything was properly cleaned.
The problem is my screen was so shattered in some places that it was really hard to remove everything so I ended up applying more pressure on the AMOLED to remove the remaining glass pieces.
So I cleaned it afterwards, and placed the new one. Booted, and VICTORY, everything works... Or so I thought.
I noticed my touch screen now behaves oddly. For example if I type too fast it will miss some letters. If I press to hard on the screen it will become like it's completely unbalanced, registering toush inputs anywhere until I close I turn the screen off and back on.
If I try to draw on the screen (in Draw Something, for example) it won't be accurate, to the point I can't really play the game anymore.
My question is : do you think I broke something when applying heat (I didn't apply that much so I don't think so) or when removing the hard-to-remove last glass pieces? Or did I simply made some mistake when replacing the glass and it's not correctly in place (I noticed it's a little higher relatively to the bezel, compared to what it was before)? Maybe it's not perfectly in place...
Thank you for your advice! I'm a noob hardware-wise so I have no idea at all what's the problem!

[Q] Screen Repair - Motherboard doesn't fit right

It looks like I should have done a little more research!
I have a Sprint Galaxy S3 and I dropped it on pavement and cracked a little bit of the corner of my screen. This is where I should have said "okay, the touch screen works, just don't mess with it any more because you know how this ends."
But I didn't... I got replacement glass first and totally screwed up that repair and left the phone in worse shape than it started. Now with the LCD and digitizer it became a slightly more expensive repair but still something I thought I could handle.
So I bought a whole LCD assembly off ebay and installed it with few problems. I bought a Samsung Galaxy S3 R530 Metro LCD Screen Touch Digitizer Frame. I stripped my phone down, moved all of the parts to the new frame and started to install the motherboard. Then's when my problems begin...
The new frame has a slightly different placement of the motherboard screw and doesn't seem to fit quite right in line with the power button. Everything else is fine and fits just right, it's just that something isn't fitting quite right. Any suggestions?
Also, my home button doesn't work any more (that's the only thing, though, so it's still a vaguely successful repair).
It sounds like I should have done some more research and I would have found that a black frame can't possibly work fully for a Sprint phone because Sprint S3s are unique for whatever reason. I'm just hoping maybe someone has a solution? A part of the frame to file down or other suggestion?
At this point I would suggest taking it somewhere to be repaired properly. Especially if you are not comfortable with the process.

Anyone ever replaced their LCD screen?

Hi all-
My MZF went for a swim a couple weeks back. Put it in a bag with some DO NOT EAT desiccant packets for a few days, actually got it to turn back on, except the Power Button didn't work and the camera crashed every time I tried to open it.
I replaced the camera module and volume rocker/power strip with OEM used parts from eBay. Phone came back on, power button and camera worked, and everything actually seemed good until I plugged the phone in to charge.
I came back a little while later and the screen is black. Phone still vibrated on fingerprint touch, and when trying to power up/down with the power button. Did not come back on reboot, and every so often can see a very brief flash on the screen. No sound either. Thinking I somehow fried the display when I plugged it back in. Thinking about getting a replacement, but all the used ones on eBay are scratchy and/or burned in, and all the "new" "OEM" ones just seem shady.
Anybody ever done anything like this? Looking for any insight!
get a scratched screen and lay a glass screen protector on it this will hide some imperfections and prevent more. i replaced my screen once already and it waqs a pain but my moto branded part works great it came from a bad imei number
Found a decent OEM screen on eBay, didn't appear to be in too bad of shape. Definitely going to put a screen protector on it to help with any scratches. Sitting in my PO box right now, and and gonna try installing it this evening!
I am debating replacing mine. The screen scratched at the FFC and made any front pictures blurry. Did some rigging as a temp fix, but the camera sensor is now not covered by the plastic. If I do replace of, I'll do a tear down video. The screen isn't too hard to remove. Of almost came of when I ripped the protector off.

Categories

Resources