i flashed cm9 modified by liumiao . i have read that it overclocks the processor speed to 806mhz . but its still showing only 600mhz for me ? any solution ?
The default setting is for 600Mhz.You have to change it yourself .Goto Settings>performance>Processor>Change the Maximum cpu frequency.Hope that helped
hassan89 said:
The default setting is for 600Mhz.You have to change it yourself .Goto Settings>performance>Processor>Change the Maximum cpu frequency.Hope that helped
Click to expand...
Click to collapse
Be careful about overclocking though, not every cpu comes out the factory alike. Some can handle overclocking better than others, if you experience any force closing of apps you should try lowering the max cpu figure. And while overclocking will give you a smoother UI experience, you may notice a reduced battery life. Good luck.
thanks mates it has helped me
Related
Hello there,
I've been flashing kernels since I was in LeeDroid Froyo and got no problems. However since I switched to GB based roms such as RCMix3D and TB Fusion, my phone always freezes when I try setting Kernel-Lee-V3.1.1-2.6.35.13-CALLREC or MDJs v19 to maximum overclock so I have no choice to but to stay on stock kernel. I have no ext3/ext4 partition on my SD card in case you ask.
Current ROM: TB Fusion 1.1.2
Radio: 12.54.60.25U_26.09.04.11_M2
Any idea what should I do to solve this issue?
golokipok said:
Hello there,
I've been flashing kernels since I was in LeeDroid Froyo and got no problems. However since I switched to GB based roms such as RCMix3D and TB Fusion, my phone always freezes when I try setting Kernel-Lee-V3.1.1-2.6.35.13-CALLREC or MDJs v19 to maximum overclock
Click to expand...
Click to collapse
uoooo this is sooo dangerous for your handset... u can "smoke" it...
Any idea what should I do to solve this issue?
Click to expand...
Click to collapse
yes, your handset freezes because the overclock that u do its too high... underclock it at 1200-1400mhz & try...
and configure SET CPU features... like the standby status, etc....but do it with common sense....
think about that DHD proccessor goes by default at 1gz, really when we overclock the processor we are putting in danger the security of our device
SERGI.3210 said:
uoooo this is sooo dangerous for your handset... u can "smoke" it...
yes, your handset freezes because the overclock that u do its too high... underclock it at 1200-1400mhz & try...
and configure SET CPU features... like the standby status, etc....but do it with common sense....
think about that DHD proccessor goes by default at 1gz, really when we overclock the processor we are putting in danger the security of our device
Click to expand...
Click to collapse
Haha! I know that overclocking is quite dangerous. Back on the froyo days, my phone is quite stable around 1.8ghz so I'm just wondering why is this happening (maybe my phone's processor is starting to fry up? ). Is there any effect if I'm using smartass profile on those kernels I've mentioned?
golokipok said:
Haha! I know that overclocking is quite dangerous. Back on the froyo days, my phone is quite stable around 1.8ghz so I'm just wondering why is this happening (maybe my phone's processor is starting to fry up? ).
i hope that the processor works or not works (don´t crashes a little bit...)
but the reason of your freezes maybe (almost sure) because froyo & gingerbread don´t works at the same form, and gingerbread need more resources & stability for to work correct... don´t forget that the kernel manages the hardware...
if u force it......... u know what can happen...
golokipok said:
there any effect if I'm using smartass profile on those kernels I've mentioned?
Click to expand...
Click to collapse
it´s possible, take this explanation, read and judge by yourself what´s the better cpu governor...
smartass (Best explanation i've found paraphrases to: based on interactive, but better.)
----
ondemand
Available in most kernels, and the default governor in most kernels. When the CPU load reaches a certain point (see "up threshold" in Advanced Settings), ondemand will rapidly scale the CPU up to meet demand, then gradually scale the CPU down when it isn't needed. - SetCPU website
conservative
Available in some kernels. It is similar to the ondemand governor, but will scale the CPU up more gradually to better fit demand. Conservative provides a less responsive experience than ondemand, but can save battery. - SetCPU website
performance
Available in most kernels. It will keep the CPU running at the "max" set value at all times. This is a bit more efficient than simply setting "max" and "min" to the same value and using ondemand because the system will not waste resources scanning for the CPU load. This governor is recommended for stable benchmarking. - SetCPU website
powersave
Available in some kernels. It will keep the CPU running at the "min" set value at all times. - SetCPU website
userspace
A method for controlling the CPU speed that isn't currently used by SetCPU. For best results, do not use the userspace governor. - SetCPU website
Interactive
The 'interactive' governor has a different approach. Instead of sampling the cpu
at a specified rate, the governor will scale the cpu frequency up when coming
out of idle. When the cpu comes out of idle, a timer is configured to fire
within 1-2 ticks. If the cpu is 100% busy from exiting idle to when the timer
fires then we assume the cpu is underpowered and ramp to MAX speed.
If the cpu was not 100% busy, then the governor evaluates the cpu load over the
last 'min_sample_rate' (default 50000 uS) to determine the cpu speed to ramp down
Click to expand...
Click to collapse
Thanks for the info
SERGI.3210 said:
because froyo & gingerbread don´t works at the same form, and gingerbread need more resources & stability for to work correct... don´t forget that the kernel manages the hardware...
if u force it......... u know what can happen...
Click to expand...
Click to collapse
You have mentioned about those "resources", is there any special measure that I need to do or what? I'm using the smartass profile on those kernels but still *sigh*
Anyway, I've observed on your sig that yours is overclocked @ 1.8ghz even though you're running GB, me envy
golokipok said:
have mentioned about those "resources", is there any special measure that I need to do or what? I'm using the smartass profile on those kernels but still *sigh*
Click to expand...
Click to collapse
you only should do a good over/underclock & set the correct cpu governor for your daily use....
well, you know ho is @MDeeJaay? the developer of MDJ kernels and roms...
he explained smartass with this words:
SMARTASS GOVERNOR - is based on the concept of the interactive governor.
I have always agreed that in theory the way interactive works - by taking over the idle loop - is very attractive. I have never managed to tweak it so it would behave decently in real life. Smartass is a complete rewrite of the code plus more. I think its a success. Performance is on par with the "old" minmax and I think smartass is a bit more responsive. Battery life is hard to quantify precisely but it does spend much more time at the lower frequencies.
Smartass will also cap the max frequency when sleeping to 245Mhz (or if your min frequency is higher than 245 - why?! - it will cap it to your min frequency). Lets take for example the 998/245 kernel, it will sleep at 245.
golokipok said:
, I've observed on your sig that yours is overclocked @ 1.8ghz even though you're running GB, me envy
Click to expand...
Click to collapse
no, no buddy... i only show the max speed nothing more... i set my cpu concretly like this;
CPU GOVERNOR:interactive
MAX SPEED:1113 MHZ
MIN SPEED:245 MHZ
PROFILE: screen off; 245 MHZ max.
245 MHZ min.
in adition i´m going to modify my syg LOL
haha..thanks again. I'm gonna try playing with the frequencies to see which will suit me
i hope someone can make a stable 1.8ghz kernel without the freeze
IT´S POSSIBLE but i don´t want to try it LOL
i love a lot my DHD
Hi guys,
I would like to tweak the voltage settings for high cpu settings eg. 2 Ghz on doomkernel but everytime I undervolt a little and I put the phone in sleep mode, it just turns off completely so there is definitely something wrong in my setting and I don't know how to set how much voltage for each cpu settings.
Can anyone give a recommended setting to undervolt?
Thank you.
spongerabbit said:
Hi guys,
I would like to tweak the voltage settings for high cpu settings eg. 2 Ghz on doomkernel but everytime I undervolt a little and I put the phone in sleep mode, it just turns off completely so there is definitely something wrong in my setting and I don't know how to set how much voltage for each cpu settings.
Can anyone give a recommended setting to undervolt?
Thank you.
Click to expand...
Click to collapse
It seems it's turning off because the clock frequency isn't getting enough power for that speed, try adjusting at 1.6ghz because 2.0ghz doesn't give that much benefit vs 1,6ghz
ff7fan4eva said:
It seems it's turning off because the clock frequency isn't getting enough power for that speed, try adjusting at 1.6ghz because 2.0ghz doesn't give that much benefit vs 1,6ghz
Click to expand...
Click to collapse
Hi thank you for the reply. So how much voltage do you recommend I set for the 1.6 ghz one? And how about the settings for the settings > 1.6 ghz?
Thank you.
Hi Everybody,
After v45 update, we all are facing huge drop in performance in our Redmi 1s.
One of my dear provided one patch by modifing some system files.
But that patch will yes revert back the performance BUT IT WILL ALSO BRING BACK THE OVERHEATING ISSUE.
So i am presenting you all with this patch.
It will restore your performance and also will control overheating.
NOTE: THIS MOD ONLY CONTROLS MAX CPU+GPU FREQUENCIES AT HIGHER BATTERY TEMPS. SO IT WONT HARM BATTERY PERFORMANCE AT ALL.
How to do:
NO ROOT IS NEEDED NOW.
JUST FLASH ZIPS EVEN THROUGH STOCK RECOVERY.
How to undo:
Just flash undo zip.
Download:
Updated in attachments as recovery flashable zips.
NOW IT CAN BE FLASHED THROUGH STOCK MIUI RECOVERY.
What have i done:
(1) somebody ask me to remove some of the line from the file but if we remove them our redmi will start overheating as it wont control the cpu.
So i have not removed them but i have set them to frequencies which will neither make phone overheat nor will hang it.
(2) file is patched with little help from my nexus.
(3) in the v45 update the cpu was limited to use less than 1ghz. It hangs the phone. So i changed it.
Now reboot and you device will go easy.
Please comment if you find any issue or suggestions.
A thanks will motivate me.
Also if you want to use my mod in any rom then plz give credits.
Credits:
Ryuinferno : for the wonderful script to sign zip files.
Notepad++
My Nexus
Update (17-11-14)
1. Removed density data from patch. Now only used cpu and gpu to control it.
2. Uploaded Hard Gaming, Power saving and Balanced patch for specific usage.
3. Cleaned and power saving based on original parameters.
What have i done :
Lets have a close look at the original \system\etc\thermal-engine-8226.conf file:
algo_type monitor
sensor batt_temp
sampling 1000
thresholds 380 390 420 500 550
thresholds_clr 370 380 400 450 500
actions cpu+hotplug_2+hotplug_3 cpu+hotplug_3 cpu+hotplug_3 cpu cpu
action_info 998400+1+0 998400+1 787200+1 600000 600000
In above lines, the sensor is batt_temp so here battery temperature is observed.
When the temperature of bettery reaches 380 (i.e. 38*C) then cpu+hotplug_2+hotplug_3 will be performed. Means cpu will clock at 998400 mhz and core2 will be hotpluged. Here your device will start hanging as 1.6 ghz cpu is asked to run at only 0.998 ghz with core2 hotpluged.
Similarly, at 390 (i.e. 39*C) core3 will also hotpluged.
35*C is normal temperature. But you will reach around 39-40*C even at light internet browsing/gaming.
At 42*C your cpu will die with only 0.787 ghz speed. This is less than half of 1.6 ghz.
Now what have i done is i have pushed the limits to little high level.
I have stopped hotplugging of cores and to low down the temp. i have used cpu & gpu both.
algo_type monitor
sensor batt_temp
sampling 1000
thresholds 390 410 420 450 550
thresholds_clr 380 400 410 440 500
actions cpu+gpu cpu+gpu cpu+gpu cpu+gpu cpu+gpu
action_info 1344000+450000000 1344000+320000000 1190400+320000000 787200+200000000 600000+200000000
Here at 39*C the cpu will go to 1.34 ghz but the gpu will remain at max of 450 mhz.
Then at 41*C the cpu will remain at 1.34 ghz but gpu will lower down to 320 mhz.
Likewise, at 420*C the cpu will go to 1.19 ghz and gpu will remain the same.
Above 45*C is too hot so the device is really needed to cool down. So above 45*C both cpu and gpu will lower down a lot for enough cooling.
Again when the temperature with lower down, you will start getting the normal speeds.
All the above information is also observed closely with the help of cpu-z apk.
is it really works ??????
why you didn't just simply configure the ondemand governor to do the same thing? Is more easy and can be done manually or using Trickster mod.
Thanks a ton for the patch but flashable zip file be a lot easier to install. So please make a flashable zip.
pgreed said:
why you didn't just simply configure the ondemand governor to do the same thing? Is more easy and can be done manually or using Trickster mod.
Click to expand...
Click to collapse
Ya but as per me if we have limited something in the thermal config file to behave at a specific battery temp. then we can not use any app or mod to change the cpu frequencies.. I have tried that also..
Also this mod controls cpu+gpu+dencity at specific battery temps...
sumitsrk123 said:
is it really works ??????
Click to expand...
Click to collapse
I also had same questions so me and my friend have tested it with the help of cpu-z app...
Cpu-z app gives you details of your battery temp. and your current cpu clock speeds. Set governor to performance and start playing games like need for speed... Then in between checked the temp of the battery and the cpu clock speed ...
It really works it changes the frequencies as per specific temps...
coolpepe said:
Thanks a ton for the patch but flashable zip file be a lot easier to install. So please make a flashable zip.
Click to expand...
Click to collapse
Yo bro... Signed flashable zips are up... Also added undo zip to revert to stock.
This is what i am using ...
I prefer little more performance over heating...
Nice....now i can use the phone @1.6Ghz without heating !!
Beast Mode Unlocked
Thanks Man for this
In a sense. But you cannot run your cpu at 1.6ghz continuously for a very long time.. Every cpu will get overheat.
Here i have tried to make some balance between the performance and heat.
What miui did.. They just tried to limit us to use at 0.99 ghz when temp is above 38.c so i have pushed that limit to high level with help of other factors like gpu and density etc.
So simple you will not be limited if you go at a high limit of temp.. After that slowly slowly cpu gpu and density will be limited and cpu will cool down...
ravinder0003 said:
In a sense. But you cannot run your cpu at 1.6ghz continuously for a very long time.. Every cpu will get overheat.
Here i have tried to make some balance between the performance and heat.
What miui did.. They just tried to limit us to use at 0.99 ghz when temp is above 38.c so i have pushed that limit to high level with help of other factors like gpu and density etc.
So simple you will not be limited if you go at a high limit of temp.. After that slowly slowly cpu gpu and density will be limited and cpu will cool down...
Click to expand...
Click to collapse
What i meant was this is smarted thermal control and i won't be having to manually underclock any more to prevent heating !
Also i can help my friends who are not aware of rooting and stuffs
No you dont need to do anything... this is balanced version..
If you prefer more power or more battery just tell me i will edit it for you according to ur needs..
ravinder0003 said:
No you dont need to do anything... this is balanced version..
If you prefer more power or more battery just tell me i will edit it for you according to ur needs..
Click to expand...
Click to collapse
Can you make it more reliable for hard gaming & multitasking??? Mod is working perfectly and really increased my battery backup and performance, No heat anymore. Thanks bro keep it up.:beer::thumbup:
Sent from my HM 1SW using XDA Premium 4 mobile app
ravinder0003 said:
Hi Everybody,
After v45 update, we all are facing huge drop in performance in our Redmi 1s.
One of my dear provided one patch by modifing some system files.
But that patch will yes revert back the performance BUT IT WILL ALSO BRING BACK THE OVERHEATING ISSUE.
So i am presenting you all with this patch.
It will restore your performance and also will control overheating.
How to do:
NO ROOT IS NEEDED NOW.
JUST FLASH ZIPS EVEN THROUGH STOCK RECOVERY.
How to undo:
Just flash undo zip.
Download:
Updated in attachments as recovery flashable zips.
NOW IT CAN BE FLASHED THROUGH STOCK MIUI RECOVERY.
What have i done:
(1) somebody ask me to remove some of the line from the file but if we remove them our redmi will start overheating as it wont control the cpu.
So i have not removed them but i have set them to frequencies which will neither make phone overheat nor will hang it.
(2) file is patched with little help from my nexus.
(3) in the v45 update the cpu was limited to use less than 1ghz. It hangs the phone. So i changed it.
Now reboot and you device will go easy.
Please comment if you find any issue or suggestions.
A thanks will motivate me.
Also if you want to use my mod in any rom then plz give credits.
Credits:
Ryuinferno : for the wonderful script to sign zip files.
Notepad++
My Nexus
Click to expand...
Click to collapse
HI Ravindar,
Thanks for your post it is helpful.
I tried it. Given better improvement.
Ram performance better
No heating
But
Battery life poor
Can u rectify
Please
What to do to RAM management with thermal control guys??
It have nothing to do with ram dear its totally cpu+gpu+density hack...
Also, this hack comes into action when you overuse your cpu and it starts heating... But at normal usage it only improves your performance at no extra battery cost...
Simple there is no use of having 1.6 ghz if you are limited to use only 0.988 ghz over 38 degrees... I have extended this limit only... As this limit is manadatory for cooling process...
For hard gaming !!! Will be uploading in some minutes...
Thanks for request...
For hard gaming !!! Will be uploading in some minutes...
Thanks for request...
Mod for hard gaming is up... Plz check the op or attachment...
My cpu is scaling to 900mhz, any one can help me to fix this at 300 mhz. I tried a lot of apps but nothing change, is there a tool to modify the cpu freq in the kernel ?
U hv to root ur phone and then install SetCPU...then set the min frequency as 300 mhz
prabhuinbar said:
U hv to root ur phone and then install SetCPU...then set the min frequency as 300 mhz
Click to expand...
Click to collapse
I tried a lot of cpu apps, look no frills cpu, set spu etc.. But nothing change, see the attachment
in general section there is a thread with Thermal Config to prevent lagging and overheating by ravinder003
Use that thermal config
SH3H1 said:
in general section there is a thread with Thermal Config to prevent lagging and overheating by ravinder003
Use that thermal config
Click to expand...
Click to collapse
I deleted the red lines in the thermal config too but now i just want to set my cpu min to 300, i juste want to modify the cpu freq in the kernel
What cpu frequency to set for gaming and also for battery saving
In No-frills Cpu set Governor to powersave and also go to nofrills cpu settings and check prevent changes from other apps.
However it may cause unexpected behaviour like hangs and slow down so better stay bit above of 300Mhz.
alok932 said:
In No-frills Cpu set Governor to powersave and also go to nofrills cpu settings and check prevent changes from other apps.
However it may cause unexpected behaviour like hangs and slow down so better stay bit above of 300Mhz.
Click to expand...
Click to collapse
I tried but the cpu freq is not changing in the scaling_min freq, cpu is min is always scaling on 900, thanks for reply
Ferhat78 said:
I tried but the cpu freq is not changing in the scaling_min freq, cpu is min is always scaling on 900, thanks for reply
Click to expand...
Click to collapse
Delete the thermal engine file. Then go to /sys/devices/system/cpu/cpu0/cpufreq/
There you'll see two files at the bottom ~ scaling_max_freq and scaling_min_freq
Change the values in them. See if it works.
EDIT: Seems like you already tried it.
alok932 said:
In No-frills Cpu set Governor to powersave and also go to nofrills cpu settings and check prevent changes from other apps.
However it may cause unexpected behaviour like hangs and slow down so better stay bit above of 300Mhz.
Click to expand...
Click to collapse
zTweaked said:
Delete the thermal engine file. Then go to /sys/devices/system/cpu/cpu0/cpufreq/
There you'll see two files at the bottom ~ scaling_max_freq and scaling_min_freq
Change the values in them. See if it works.
EDIT: Seems like you already tried it.
Click to expand...
Click to collapse
Thabks for reply, but i can change the value of the cpu min scaling, it's impossible to change, i changed but after a reboot a have always 900mhz min
Ferhat78 said:
Thabks for reply, but i can change the value of the cpu min scaling, it's impossible to change, i changed but after a reboot a have always 900mhz min
Click to expand...
Click to collapse
Check apply on boot in no frills cpu. However it wont always stay on 300 bcoz its based on performance. if you want it to stay near to 300 always then reduce max freq. If it still doesnt work and you are on miui then change your rom...Try using mokee rom.
alok932 said:
Check apply on boot in no frills cpu. However it wont always stay on 300 bcoz its based on performance. if you want it to stay near to 300 always then reduce max freq. If it still doesnt work and you are on miui then change your rom...Try using mokee rom.
Click to expand...
Click to collapse
Tried kernel tuner 2014 and now the cpu is scaling on 300, thanks for reply everybody, thanks a lot for yours answers kernel tuner work perfectly but no frills cpu or setcpu doesnt work perfectly look like kernel tuner
Need help or advice , last week i've been using lollipop rom, im not familiar to the new settings and setups on this so i explore and try the kernel settings. I set my kernel setting to maximum, like cpu which is about 1750 mhz all cores and gpu 450 thermal off etc. Because i hve been seen some comment that the lollipop rom reaches to about 27000 k antutu score . i tried it by my settings which is my phone crashed while testing it to about 25% of testing. Now i just go back to sling rom and try again to test with no modification with the kernel or any optimizing the performance and im surprise that it crashed too and tested with putting my phone on the freezer which i guess im having phone temperature problem but it crashed too. Now while charging and testing in the same time it completes the benchmarking of my phone.
I guess my battery is the reason my phone is crashing when on the heavy load of using
Or some hardware issues? Like cpu,gpu ??
Sorryto my bad english and explanation. Thanks
delacruzivancarlo25 said:
Need help or advice , last week i've been using lollipop rom, im not familiar to the new settings and setups on this so i explore and try the kernel settings. I set my kernel setting to maximum, like cpu which is about 1750 mhz all cores and gpu 450 thermal off etc. Because i hve been seen some comment that the lollipop rom reaches to about 27000 k antutu score . i tried it by my settings which is my phone crashed while testing it to about 25% of testing. Now i just go back to sling rom and try again to test with no modification with the kernel or any optimizing the performance and im surprise that it crashed too and tested with putting my phone on the freezer which i guess im having phone temperature problem but it crashed too. Now while charging and testing in the same time it completes the benchmarking of my phone.
I guess my battery is the reason my phone is crashing when on the heavy load of using
Or some hardware issues? Like cpu,gpu ??
Sorryto my bad english and explanation. Thanks
Click to expand...
Click to collapse
See this thread and check you PVS value of CPU....
http://forum.xda-developers.com/nexus-4/general/poll-cpu-binning-t2052496
If you are getting slower or slow PVS, try to increase the voltage of 1750mhz freq and run the benchmark...
Hope it helps
hasan4791 said:
See this thread and check you PVS value of CPU....
http://forum.xda-developers.com/nexus-4/general/poll-cpu-binning-t2052496
If you are getting slower or slow PVS, try to increase the voltage of 1750mhz freq and run the benchmark...
Hope it helps
Click to expand...
Click to collapse
Thank you . the result of my PVS is 4. I also suspect that i have low voltage to run the processor thats why when im doing benchmark it shutdown even playing COC.
How can i change my voltage and what is the default voltage ? Thank you again.
delacruzivancarlo25 said:
Thank you . the result of my PVS is 4. I also suspect that i have low voltage to run the processor thats why when im doing benchmark it shutdown even playing COC.
How can i change my voltage and what is the default voltage ? Thank you again.
Click to expand...
Click to collapse
trickster mod or faux clock app...