I have an epic sitting at home that is useless as of right now because I no longer have a plan through sprint for it. I have a samsung replenish that I am using right now with Boost, and I am considering making it a donor phone and flashing the Epic over to Boost. Having this little thing really makes me realize just how awsome those Super AMOLED displays are. Anyway, I have a few questions before getting neck deep in this little endevour. First off, I don't want to be stuck on Eclair, but as I understand a Factory reset is necessary to get the 3G working, I read that people were abale to flash to Froyo using a few tricks, I was just wondering if the same works for Gingerbread. If anyone is running a Boost Epic on GB I would like to know how it is working out. Also, once the phone is flashed to said version of Android, can I just flash any rom on top of it through CMW without having to make tweaks?
And finally, I can not get either the Replenish or the Epic to read on CDMA Workshop, I have tried debug, non-debug, and diag modes and any combination, I have tried reading the phones in recovery mode, I have rebooted, restarted, unplugged, switched cables and ports....nothing...the phones both show up as modems and have their ports listed in device manager, but they absolutely refuse to show up, if anyone has any tricks that they could share regarding this issue it would be much oblidged
I know it's a lot but I figured I would try and cover all of my questions in one thread rather than making a bunch of seperate ones. BTW I have been researching for 2 days now, if there is something obvious that I missed, I apologize in advance, but I have tried other methods of resolution before creating this thread...Thanks in advance for any advice that you guys can offer...
We have a guide on here did you consult that? And I know that there is an alternative carrier fix for cm9 so you "could" get that puppy on android 4.0 =]. As for the computer not detecting... did you install the mobile drivers for the phones? I think you might need to if you haven't. I know when odining you need those I suppose the same for cdma workshop. Hope this helps at all =]. if you need the guide ill link it here.
Flashing Epic 4g to Boost Mobile Guide.
In this guide he is using the incognito but as long as you have a cdma phone to use as a donor phone you should be fine. If you havnet installed the drivers for either phones then this is most likely your issue. Also according to the guide you CAN flash other ROMs. The only thing that needs to be tweaked is the sms settings.
Yeah, I have looked at the guide, I was hoping to clarify on the few items that I wasn't clear on. I have installed the drivers for both phones and Odin does infact recognize each one, I use it to verify the Com ports that the phones are on...i'm baffled :/
After hours more of trying...and researching..I still can not get past the initial step of getting cdma to read my phones...either of them. Is there a section on this forum for requesting services? I dont care if I have to pay to get it done, I want my epic on boost...
bugzy3188 said:
After hours more of trying...and researching..I still can not get past the initial step of getting cdma to read my phones...either of them. Is there a section on this forum for requesting services? I dont care if I have to pay to get it done, I want my epic on boost...
Click to expand...
Click to collapse
I doubt it... but who knows. I dont see why they wont detect. They should if you have the drivers installed... maybe try just having one of the phones drivers installed at once... which ever phone you have to start off with have that phones drivers installed only. so unistall both then install just one that you need then unistall that one when the other one needs to be used... and you might want to reboot in between driver installations. drivers can be very picky. Or you could try another computer...
I'll give it a shot, its something new at least...I will post my results when I am done..
bugzy3188 said:
I'll give it a shot, its something new at least...I will post my results when I am done..
Click to expand...
Click to collapse
I know some having success doing this because they had their epic touch and epic 4g drivers installed once they unistalled both and just installed the epic 4g the computer would recognize it.
tried uninstalling all samsung mobile drivers and installing the drivers for each phone by themselves, still nothing...I am downloading a new set of drivers now, they are generic Samsung mobile drivers.I'm not expecting much but its all I got at this point...
bugzy3188 said:
tried uninstalling all samsung mobile drivers and installing the drivers for each phone by themselves, still nothing...I am downloading a new set of drivers now, they are generic Samsung mobile drivers.I'm not expecting much but its all I got at this point...
Click to expand...
Click to collapse
HMM i know which samsung drivers work great for the epic but i think you need device specific drivers for the replenish.
32 and 64 bit Drivers I know the drivers here work great and i have used them with every epic i've rooted... I just learned that the drivers im linking you to work for the replenish .
awesome, I am trying them as we speak...
ah crap, those were the same drivers that I downloaded for the Replenish, still a no go...the fact that neither phone works would tell me its on the PC end, and drivers would be the number one suspect, but alas...they just aren't making a difference in my results..
bugzy3188 said:
ah crap, those were the same drivers that I downloaded for the Replenish, still a no go...the fact that neither phone works would tell me its on the PC end, and drivers would be the number one suspect, but alas...they just aren't making a difference in my results..
Click to expand...
Click to collapse
Yeah you might need to try another computer. The usb ports could be bad/out on that one depending on how old it is. Or it could be the usb cable as well you'd be amazed at how much trouble is cause by those. Have you tried a brand new blackberry cable? those are the best cables at getting things recognized. What i dont get is that odin will COM the phone.... and this is in download mode right?
no, it coms both phones in debug mode, I have a few blackberry cables lying around that I have picked up on Amazon that I bought for Odin. Thats what kind of has me scratching my head too. It is an older laptop though, Id say about 4 years old, running windows 7 x64...I have checked QPCT as well just to see if it recognizes the phones and it doesnt either, so I guess it's some issue with my com port's compatibility with the mobile phone software....I will see if I can get away with doing this at work tomorrow, it may be tricky but my boss is old and senile lol
Well I tried it at work with no luck yet, which just leaves human error in to play...not sure what though, I've covered all of the options that I have come across. The replenish I could understand, but the Epic is documented to work just fine with CMDA WS...I just don't get it...
A couple things to try...
1. Connect the phone in normal mode (so it asks mass storage, etc) and let the drivers install.
2. Unplug, turn on USB debugging (Settings -> applictaions -> Development), plug the phone in and let it install ADB driver
3. With phone plugged in switch to dialer and hit ##8778#, then switch USB from PDA to Modem. Your PC should install another driver (Diag port).
Make sure you leave the Epic on this screen while accessing it via CDMAWS or any other program that uses the diag port.
I had major issues with the Epic, but that sequence finally got everything working. I still need to plug the phone in before enabling the diag port, otherwise stupid things happen.
This was all with an XP computer (three actually, before I figured out all the correct steps).
Thanks, I'll try that when I get home, I actually haven't tried putting it in diag mode while plugged in yet, I have always put it in diag and connected it...heres hoping..
ok, I finally got the replenish to connect, I found a way to root it and that worked like a charm....the epic however is still a no go...rooted running CWM 5, in diag mode, switched to modem, recognized as a modem....but still..failed...phone does not answer...any other suggestions guys?
Needs download mode not diag mode whatever that is... hold the 1 on the keyboard and the power button (yellow triangle) make sure is not in modem mode and you must flash the kernel from mkasick for ei22 search in xda "epic 4g gb kernel source" should me the first thread (ei22) kernel source with keyfix. Scroll to the bottom and find the gb3a.tar this is what you odin before cwm5 and it should stick. Then you can flash an su.zip and your done.
Sent from my SPH-D700 using xda premium
ÜBER™ said:
Needs download mode not diag mode whatever that is... hold the 1 on the keyboard and the power button (yellow triangle) make sure is not in modem mode and you must flash the kernel from mkasick for ei22 search in xda "epic 4g gb kernel source" should me the first thread (ei22) kernel source with keyfix. Scroll to the bottom and find the gb3a.tar this is what you odin before cwm5 and it should stick. Then you can flash an su.zip and your done.
Sent from my SPH-D700 using xda premium
Click to expand...
Click to collapse
I was on EL30, which from my understanding worked as well. I flashed the gb3a and I am rooted with CWM and I installed SU, I just still can't get cdmaws to see the phone...I tried fix permissions, in CWM, not even sure what that does, but I tried it...i'm desperate lol. I have tried tether mode, switching ports, attempting while in recovery, and I get nadda....EL30 was what I had factory reset to, are you saying that I should flash back to ei22 for cdma or were you saying to do that to get it rooted?
No my appologies I, just read you rooted correctly. I'm not sure why it refuses to recognize the epic. Other than a better cable, or different usb port. I dunno. That or there is gunk in the epics usb port or in the computers. Should be in modem mode I'm assuming if your messing with the phoney. Stuff ='[ sorry.
Sent from my SPH-D700 using xda premium
Related
I've been trying to root my epic 2.2 with gingerbreak and it doesn't work. I've done It before and now it says "Not sure what happened.exploit failed or reboot failed. Reboot manually and see if you have Superuser" I did everything right
Does anyone know how to fix this?
mummer96 said:
I've been trying to root my epic 2.2 with gingerbreak and it doesn't work. I've done It before and now it says "Not sure what happened.exploit failed or reboot failed. Reboot manually and see if you have Superuser" I did everything right
Does anyone know how to fix this?
Click to expand...
Click to collapse
Use the 1 click
Sent from marcusantrom v5
marcusant said:
Use the 1 click
Sent from marcusantrom v5
Click to expand...
Click to collapse
Which one?
The one for cwm 3.0.2.5
if you cant live large, look big in the coffin!!!
Also, supposedly, gingerbreak only works on phones that have odined to ec05. That's the consensus at least.
Sent from my perfect epic
musclehead84 said:
The one for cwm 3.0.2.5
if you cant live large, look big in the coffin!!!
Click to expand...
Click to collapse
I keep getting "phone not connected" any suggestions
I have tried all available options for troubleshooting and can not figure it out. The drivers are good, different cords, different Root techniques, I mean everything ... but my phone won't connect even after re-installing the samsung drivers.
Windows Vista
64 bit
phone EC05
firmware 2.2.1
stock everything
hooover said:
I keep getting "phone not connected" any suggestions
I have tried all available options for troubleshooting and can not figure it out. The drivers are good, different cords, different Root techniques, I mean everything ... but my phone won't connect even after re-installing the samsung drivers.
Windows Vista
64 bit
phone EC05
firmware 2.2.1
stock everything
Click to expand...
Click to collapse
Did you try a different usb port or a different pc, if available?
Sent from my perfect epic
zanderman112 said:
Did you try a different usb port or a different pc, if available?
Sent from my perfect epic
Click to expand...
Click to collapse
I have tried all ports on my PC, no I haven't tried to use another PC though.
I just Rooted my friends brand new epic 10 days ago. I just can't figure out how to make my device connect as itself instead of "unknown"
Try the Bonsai MasterKey Unlocker, you will like it better than the stock CWM 3.0.2.5
Sent from Bonsai 7.1.1.1
I am also going thru the same senerial a you... if you find a "fix" for this will you please reply....like wise from me. I have even tried putting th e epic in "DL" mode. But odin does not acknowlege my phone. Hit me up . Thnx.
Sent from my SPH-D700 using XDA App
Get a better usb cable radioshack has gold tip usb cables they always work. Or go too verizon and buy the usb cable for the droid pro
Top Nurse said:
Try the Bonsai MasterKey Unlocker, you will like it better than the stock CWM 3.0.2.5
Sent from Bonsai 7.1.1.1
Click to expand...
Click to collapse
I second this
pacoz said:
I am also going thru the same senerial a you... if you find a "fix" for this will you please reply....like wise from me. I have even tried putting th e epic in "DL" mode. But odin does not acknowlege my phone. Hit me up . Thnx.
Sent from my SPH-D700 using XDA App
Click to expand...
Click to collapse
Before Odin can detect it you must first make sure your computer can detect your phone. That way you'll know if the drivers work fine. If it does then get a new USB cable to connect it while using odin. I got a rocketfish usb cable and it works better than the samsung one...or any usb cable such as a blackberry's works fine.
hooover said:
I have tried all ports on my PC, no I haven't tried to use another PC though.
I just Rooted my friends brand new epic 10 days ago. I just can't figure out how to make my device connect as itself instead of "unknown"
Click to expand...
Click to collapse
When trying to root make sure you aren't using a stock samsung usb cable. Some have been successful using them while rooting but for most it sucks. Are you enabling usb debugging?
I am having the same problem. Gingerbreak failed to run with the same error, and no amount of different cable or port (tried three of each) will avoid the phone not connected message when attempting one click root. I'd love to hear ideas to resolve either of these or other rooting options.
Update - tried the Bonsai unlocker mentioned in this thread, and tried the one click method on a second machine to which I had never connected my device. In all cases, got a phone connection failure. And yes, I have enabled USB debugging, and when I disable it, I am able to mount the phone just fine and see the external memory card, so there's nothing wrong with the USB port or cable. I have a relatively new replacement phone that came preloaded with Froyo. Maybe something has been done to newer devices to disable this ability? Can't imagine what else could be wrong.
thanks,
-- robert
rmingee said:
I am having the same problem. Gingerbreak failed to run with the same error, and no amount of different cable or port (tried three of each) will avoid the phone not connected message when attempting one click root. I'd love to hear ideas to resolve either of these or other rooting options.
Update - tried the Bonsai unlocker mentioned in this thread, and tried the one click method on a second machine to which I had never connected my device. In all cases, got a phone connection failure. And yes, I have enabled USB debugging, and when I disable it, I am able to mount the phone just fine and see the external memory card, so there's nothing wrong with the USB port or cable. I have a relatively new replacement phone that came preloaded with Froyo. Maybe something has been done to newer devices to disable this ability? Can't imagine what else could be wrong.
thanks,
-- robert
Click to expand...
Click to collapse
My bad - apparently I didn't have the right drivers installed. I assumed since I could connect in USB mode without debugging I had the right drivers, but apparently not. Sorry to bother. In case anyone else runs into this, I apparently can't post a URL to help you, so go look for a post on the Epic "All Things Root" forum on Android Forums,
It appears I am successfully rooted after having to reboot the phone once after a failure the first time I ran. Woohoo! Now I can do a true full backup.
-- robert
The only way I could get mine to work (I would get the same errors using gingerbreak) I restored the phone to factory settings using the samsung recovery mode. Press power volume down and camera button. Your volume buttons are used to highlight the text and the home key is used to select. Wipe cache 3 times, and wipe the dalvick (spelled wrong) 3 times, then reset phone back to factory settings through here. Remember you will lose everything so back up your apps using AppBrain. I ran GingerBreak again and it worked perfectly. I would also get the same errors when trying to odin. Its been that way everysince I updated to 2.2. By the way I am EC05, did that before I updated because I was running midNight Rom.
Sent from my SPH-D700 using XDA App
*First of all, let me say that this is a repost from here (http://forum.xda-developers.com/showthread.php?t=1153310&page=27), and I apologize for that fact. I have been severely neglecting food and sleep trying to fix my phone, and I really, really didn't feel like typing the whole damned story up again. Any assistance or insight would be deeply appreciated...
-------------------------------------------------------------------------------
Well, I did it this time I think. I've hacked, modded, wiped, and flashed my phone since I got it last year, and although I've gotten to places where I thought I had totally fuxored things up beyond recovery, every single time in the past I've been able to bring it back from the brink of oblivion. I am exceedingly resourceful and tenacious, which can be both a good and bad thing. Good thing when I am able to fix things that seem unfixable. Bad when I forget about things like eating or sleeping.
Here's the present situation: 4 days ago I was trying to flash a new modem (FB15)(something I know well how to do as I've done it many, many times before) through Odin, when it stalled out near the beginning of the process. This is not unusual with Odin, so I've gotten into the habit of closing it, pulling the battery, and starting again. This time, however, no matter what I've tried, I cannot get Odin to successfully flash. It fails every single time. Either that or it stalls yet again.
At the moment I can only get into 2 modes on my phone: download mode (which can't actually download anything apparently) and the very unpleasant computer--!--phone screen when I try to boot it up or go into recovery. This is the longest my phone has been unusable. I've been intensely focused on fixing it since it was semi-bricked. The ridiculously frustrating and annoying thing is that the computer I'm using (and I've used multiple to try to fix this across Windows, Linux, and Mac) usually says "USB device not recognized" when I plug my phone in while in download mode, no matter the state of the drivers, and when it does recognize it and it is visible in Odin, it means nothing because Odin fails no matter what file I'm trying to flash. When the computer and Odin DO recognize the phone, and when Odin doesn't hang, very occasionally it will give me some odd error message like "PIT mapping not found" or "cannot open COM port". I've tried so many of the things I've tried in the past that have worked: changing USB ports, rebooting the computer between attempts, uninstalling and reinstalling drivers, going into download mode with the SD-card and battery out and in, loading Odin after or before putting the phone into download mode, trying on different computers with different versions of Windows (I even tried one Mac with iOS 10.4 and a Linux notebook with Ubuntu), trying different USB cables, flashing with the battery and SD card out, trying to flash different files (besides the original modem.bin which stalled), running Odin as administrator, yadda, yadda, yadda...on and on, for days. I even just went out and bought a high-performance, super-short USB cable (6-inches) and a USB 3.0 PCI card so I'd have dedicated USB. Nada.
Basically my phone seems to have a broken download mode with potentially wonky USB (Samsung USB has never been good). I've been seeing if I can get Heimdall to work, though there is a bit of a learning curve with that program, no matter how easy people say it is. I've never even tried flashing it with it yet since I haven't gotten together all of the apparently necessary files. I also just found One-Click Unbrick, and while I was excited originally, it seems that the same outcome is the result. No matter what I do to get everything just right to be able to succeed, it fails. Java is installed, Heimdall is apparently installed, and the One-Click Unbrick drivers have been installed every time I've tried to run it. Nada again.
If my phone is able to get into download mode, yet that seems to be borked, what is my recourse? I'm at the end of my rope...*sinks into a depressed lump on the floor*.
ANY assistance would be immensely appreciated. Thank you all in advance. I'm not incredibly hopeful at this point, but I am (fortunately or unfortunately) still tenacious as hell. :-/
Setup:
Phone: Samsung Epic 4g
ROM: SleeperROM 2.0.04 EL30/MTD (Gingerbread 2.3.6)
Kernel: The last available Samurai kernel
Recovery: ClockworkMod Recovery 5.0.2.7
Filemap/Filesystem: MTD/Yaffs2
Present Computer: Windows Vista Home Premium 32-bit/AMD desktop
Modes available on phone: download and computer--!--phone screens
Issue: cannot flash anything in download mode via Odin on present computer
Wow im glad i didnt have to go through this i was trying to flash the fb15 modem recently as well and it wouldnt go through all i did was go and find the el30modem tar and flashed that and i was all good again. ... youve tried literally every suggestion i was going to say. other than try flashing the el30modem.tar? I know for sure its good its in android development if you can get odin to COM im sure it will work...
http://forum.xda-developers.com/showthread.php?t=1501424
add me on gtalk
crystylizd[email protected] and ill see if i cant help you out.
Big Goron said:
Wow im glad i didnt have to go through this i was trying to flash the fb15 modem recently as well and it wouldnt go through all i did was go and find the el30modem tar and flashed that and i was all good again. ... youve tried literally every suggestion i was going to say. other than try flashing the el30modem.tar? I know for sure its good its in android development if you can get odin to COM im sure it will work...
http://forum.xda-developers.com/showthread.php?t=1501424
add me on gtalk
[email protected] and ill see if i cant help you out.
Click to expand...
Click to collapse
I thank you much for your suggestion. I've tried flashing the EC05 modem tar and both the tar.md5 and the straight tar file of the stock EL ROM, though surprisingly I haven't tried the straight EL30 modem tar yet. I'll try when I get home. The main problem is not getting Odin to COM, but getting it to flash anything. It either stalls, fails, or doesn't see the phone...download mode seems to be basically useless.
homam_france said:
@+Que ppc really your BA downgrade and upgrade is long story,did u finish it?i hope the answer is yes,about the hexaguns we cannot return back to it,but i can make modification to the new components of the new build,capish
Click to expand...
Click to collapse
If you get it to recognize still then Odin with the battery and sd card out.
Sent from my SPH-D700 using xda premium
kennyglass123 said:
If you get it to recognize still then Odin with the battery and sd card out.
Sent from my SPH-D700 using xda premium
Click to expand...
Click to collapse
I usually flash in Odin with the battery and SD card out. No go.
tydynrain said:
I usually flash in Odin with the battery and SD card out. No go.
Click to expand...
Click to collapse
It is possible you have some crap in your phone's port. Or even the new cable is flaky. Get a bright light and magnifying glass and look in your phone's port. Also try fresh downloads of the files.
Sent from my SPH-D700 using xda premium
kennyglass123 said:
It is possible you have some crap in your phone's port. Or even the new cable is flaky. Get a bright light and magnifying glass and look in your phone's port. Also try fresh downloads of the files.
Sent from my SPH-D700 using xda premium
Click to expand...
Click to collapse
I'l check the USB/charging port when I get home from work. Most of the files I've used, including the various versions of Odin, came from my synched Dropbox folder. I'm wondering now if Dropbox synches files accurately. I'll try redownloading every file I use to flash to see if it has a beneficial effect. Thanks for the suggestion.
hope this helps
tydynrain said:
I'l check the USB/charging port when I get home from work. Most of the files I've used, including the various versions of Odin, came from my synched Dropbox folder. I'm wondering now if Dropbox synches files accurately. I'll try redownloading every file I use to flash to see if it has a beneficial effect. Thanks for the suggestion.
Click to expand...
Click to collapse
Let me find you some reliable files
Odin 1.85
Stock El30
Windows 32 bit and 64bit drivers
This should be enough to get you on your way. Oh and if you can at all possible reinstall windows prior to loading these drivers. i know someone who had to do it before their computer would recognize their phone. I've been in this kind of situation i had someone root my phone and is computer was fubar'd and it took him 3 days to unbrick my phone. This is what helped him he kept recieving unknown device. This is what helped is what helped him id advice the same. Once you have windows reinstalled download the three things and install the drivers and give it a shot.
Big Goron said:
Let me find you some reliable files
Odin 1.85
Stock El30
Windows 32 bit and 64bit drivers
This should be enough to get you on your way. Oh and if you can at all possible reinstall windows prior to loading these drivers. i know someone who had to do it before their computer would recognize their phone. I've been in this kind of situation i had someone root my phone and is computer was fubar'd and it took him 3 days to unbrick my phone. This is what helped him he kept recieving unknown device. This is what helped is what helped him id advice the same. Once you have windows reinstalled download the three things and install the drivers and give it a shot.
Click to expand...
Click to collapse
Thank you so much for the time. I'll see about reinstalling Windows, though since it's not my computer I'm not too sure how that will go...hehe. I may be able to restore from the backup partition if he doesn't have a CD.
well you can do it over a virtual machine but unsure how to do this and if this will work entirely it might it might not im not too fluent with virtual machines.. but it simulates a working computer so id imagine you can install drivers and see if it will then recognize your phone.
Big Goron said:
well you can do it over a virtual machine but unsure how to do this and if this will work entirely it might it might not im not too fluent with virtual machines.. but it simulates a working computer so id imagine you can install drivers and see if it will then recognize your phone.
Click to expand...
Click to collapse
So interesting that you mention running a virtual machine, as since I can't reinstall Windows Vista on this system, I was considering partitioning the hard drive and installing a version of Linux, then running WINE under that.
Lol try that... or windows i think windows might be your best bet...
Sent from my SPH-D700 using xda premium
Whoa whoa, tdy...queston. have u manually installed ur driers directly from samsung website?
Sent from my SPH-D700 using xda premium
Kies drivers worked for me
Sent from my SPH-D700 on CM9 beta0 using xda premium
I FIXED IT! My phone which has been dead for 5 days lives again! Resurrected!
I thank you all for your time and assistance. It was very deeply appreciated.
I fixed it by circumventing Winblows entirely. I created a second partition on my friend's hard drive, installed Ubuntu Linux 11.10, then went through the pretty simple process of setting up Android SDK/ADB and Heimdall, and all of the dependencies that they required. The ridiculous thing is that I fixed it without even trying. I was simply seeing if Heimdall could detect my phone (which I had connected and in DL mode), which I noticed that it did. I had no idea what Download PIT did, so I pressed it, and lo and behold, it did something amazing, and rebooted my phone. I am elated, exhausted, triumphant!
WHOOT!!!
I kNEW I would figure it out. I always do...lol.
In messing up my phone so many times, I have gotten VERY good at fixing whatever nonsense happens to arise.
Thanks again all.
Tydyn.
EDIT: I meant PRINT PIT, not Download PIT. ;-)
YAY!
tydynrain said:
I FIXED IT! My phone which has been dead for 5 days lives again! Resurrected!
I thank you all for your time and assistance. It was very deeply appreciated.
I fixed it by circumventing Winblows entirely. I created a second partition on my friend's hard drive, installed Ubuntu Linux 11.10, then went through the pretty simple process of setting up Android SDK/ADB and Heimdall, and all of the dependencies that they required. The ridiculous thing is that I fixed it without even trying. I was simply seeing if Heimdall could detect my phone (which I had connected and in DL mode), which I noticed that it did. I had no idea what Download PIT did, so I pressed it, and lo and behold, it did something amazing, and rebooted my phone. I am elated, exhausted, triumphant!
WHOOT!!!
I kNEW I would figure it out. I always do...lol.
In messing up my phone so many times, I have gotten VERY good at fixing whatever nonsense happens to arise.
Thanks again all.
Tydyn.
Click to expand...
Click to collapse
CONGRATS im happy you got your phone back i know how you feel finally getting your phone back i went through the same deal cept it was with someone else. Oh and im jealous you have 11.10 working i couldnt get it working right with my laptop gpu drivers.. fail. anyways glad you got it
Big Goron said:
CONGRATS im happy you got your phone back i know how you feel finally getting your phone back i went through the same deal cept it was with someone else. Oh and im jealous you have 11.10 working i couldnt get it working right with my laptop gpu drivers.. fail. anyways glad you got it
Click to expand...
Click to collapse
Thank you brother! I am practically jumping around the house singing...lol. Ubuntu 11.10 is freaking gorgeous! It is the most amazing operating system I have ever used. I am in love!
tydynrain said:
Thank you brother! I am practically jumping around the house singing...lol. Ubuntu 11.10 is freaking gorgeous! It is the most amazing operating system I have ever used. I am in love!
Click to expand...
Click to collapse
Yeah i love it as well im sadly stuck with 10.04 which isnt bad but i like the newest ones UI its just so much more appealing than 10.04 but 11.10 doesnt like my GPU and is incompatible i do know a work around but have already got settled in 10.04
Big Goron said:
Yeah i love it as well im sadly stuck with 10.04 which isnt bad but i like the newest ones UI its just so much more appealing than 10.04 but 11.10 doesnt like my GPU and is incompatible i do know a work around but have already got settled in 10.04
Click to expand...
Click to collapse
My housemate is running 10.04, so I'm familiar with how it looks. If it makes ya feel any better 11.10 doesn't like my new usb wireless network adapter (Netgear N900 Dual Band), which is MUCH better than the one to which I had to revert to get internet access, though I'm hoping that I can get it working somehow soon.
tydynrain said:
My housemate is running 10.04, so I'm familiar with how it looks. If it makes ya feel any better 11.10 doesn't like my new usb wireless network adapter (Netgear N900 Dual Band), which is MUCH better than the one to which I had to revert to get internet access, though I'm hoping that I can get it working somehow soon.
Click to expand...
Click to collapse
I had alot of trouble even getting internet to comply... i finally got it to speed up using wifi and even that was a pain in the arse luckily other people had my same issue and had a resolution for it. I know you have to have the drivers for said wireless adapter installed for it to work correctly otherwise its not going to work
Hi, I am new to the epic touch. I had a rooted epic 4g. I know how to use odin and I've downloaded the .Tar files for the root acess and the drivers for samsung. It is also a brand new USB cable. I need help because odin doesn't see my phone when it is plugged in and in download mode. When the phone is on and i plug it into the computer Windows reconizes my phone fine. I am so ready to root this thing but I can't. Can someone tell me what I'm doing wrong or point me in the right direction?
New phone: epic 4g touch Stock
Old phone: epic 4g, CWM Recovery, Thunderhawk V ROM, Samuria Kernel, And OC'd 1.2 GHz
g_ding84 said:
Hi, I am new to the epic touch. I had a rooted epic 4g. I know how to use odin and I've downloaded the .Tar files for the root acess and the drivers for samsung. It is also a brand new USB cable. I need help because odin doesn't see my phone when it is plugged in and in download mode. When the phone is on and i plug it into the computer Windows reconizes my phone fine. I am so ready to root this thing but I can't. Can someone tell me what I'm doing wrong or point me in the right direction?
New phone: epic 4g touch Stock
Old phone: epic 4g, CWM Recovery, Thunderhawk V ROM, Samuria Kernel, And OC'd 1.2 GHz
Click to expand...
Click to collapse
I would make sure that no other Samsung software or drivers are installed. Also, check your device manager to make sure that the drivers installed for your phone when you plugged it in.
Thank you. I will try this when I get home tonite.
g_ding84 said:
Thank you. I will try this when I get home tonite.
Click to expand...
Click to collapse
Goodluck and let us know what happens.
Try to run Odin as administrator.
Sent from my SPH-D710 using XDA
Second everything said already. 1st uninstall/remove ANY samsung drivers on your PC. You may have to look in device manager for 'hidden devices' too. Redownload and install (as administrator) the Samsung drivers. Reboot your system. sfhub has the links for everything here http://forum.xda-developers.com/showthread.php?t=1705730 . When running the One-click make sure you also run that as Administrator too. Also do try another USB cable and/or USB port too.
This might be kinda obvious but have you tried a different usb port? Sometimes just switching to a new port will get it to recognize it.
Sent from my SPH-D710 using XDA
Thank you huys so much. Ill try another USB port as well. But that is the same port that I have always used. I have a few cables so ill try that as well.
Edit, I had the wrong Samsung drivers. Success, fully rooted! Thank you everyone
just install skies
re
I thought I did install it. but I had the epic 4g drivers from my old phone. Guess I got confused.
g_ding84 said:
I thought I did install it. but I had the epic 4g drivers from my old phone. Guess I got confused.
Click to expand...
Click to collapse
Glad to hear you got it working. It's usually the simple things that's why I mentioned the drivers because you mentioned the previous phone. I've seen that happen before. Stick around, do loads of reading and you'll find this is a fantastic community. Enjoy your phone.
leaderbuilder said:
Glad to hear you got it working. It's usually the simple things that's why I mentioned the drivers because you mentioned the previous phone. I've seen that happen before. Stick around, do loads of reading and you'll find this is a fantastic community. Enjoy your phone.
Click to expand...
Click to collapse
This is an ae community. I just learned about this site back in may. And issues or new roms, kernels or themes I got from here. Everyone is very helpful. Lol, I just need to learn this phone now.
Okay, so, yes I'm a noob. I've been up literally all night trying to figure out why my signal did not connect after flashing Synergy for my SGH-T999.
So I read a thread saying to do a full wipe, back up then reflash the rom. (I still did custom installation with zigggy kernel, so i'm unsure if it is the kernel or not)
My second time flashing the Synergy Rom I have signal but says 3G and H+ ... i have a 4G data connecton and it does browse pretty fast but the most bars I get in my house at 1-3 and normally i get atleast 4, and constant 4G connection.
I'm unsure if it is necessary to flash a Radio. In the past I've bricked my phone and screwed up the signal permanently by flashing the wrong radio, lost my RSA keys etc.
I dont want to make the same mistake twice so here I am.
EDIT: After all that time I find http://forums.androidcentral.com/sa...e-why-dose-my-new-rom-say-h-h-instead-4g.html
From what i understand H+ doesnt mean anything? Its just the Rom being more accurate instead of saying 4G? Is this true?
It also does seem like my signal is weaker then before, could flashing a new radio/modem fix this?
The rom showing H is probably ok. Check in the rom thread but some devs did this because its more accurate.
As for signal, as long as you have a T999 model, you can safely flash any modem in my thread. Ive yet to find someone reporting a bricked S3 so long as they read the OPs and follow directions.
Many of us have flashed dozens of times!
Sent from my SGH-T999 using xda premium
Thank you so much sir I didnt expect such a quick reply. I will definitely check some modems out, any specific one you recommend? like a universal choice? i might turn into a rom flashaholic x)
EDIT: Wait a minute, i dont have the Wind T999, i have the regular T999. Your thread says "Only flash if you have T999V." Will this affect anything?
Actually the thread is for both the T999 and T999V. The T999V modems are towards the bottom and clearly labeled for each of the Canadian carriers.
Dont flash those. Just the ones under the T999 heading. Theres a bunch.
As far as best one. There is no universal one. Different ones are better for different people. Depends mostly on location which is what the map is there for. See if anyone in your area has posted any results.
Sent from my SGH-T999 using xda premium
DocHoliday77 said:
Actually the thread is for both the T999 and T999V. The T999V modems are towards the bottom and clearly labeled for each of the Canadian carriers.
Dont flash those. Just the ones under the T999 heading. Theres a bunch.
As far as best one. There is no universal one. Different ones are better for different people. Depends mostly on location which is what the map is there for. See if anyone in your area has posted any results.
Sent from my SGH-T999 using xda premium
Click to expand...
Click to collapse
Will do! i came upon the UVLI8 and UVMD5, i'll be trying all kinds of them.
But upon trying to put this onto my phone via USB. My computer is not detecting my phone, this was working the first time i flashed the Synergy rom. -_- Do i have to reflash again? I have all samsung drives, kies, debugging enabled. ive tried it in different ports and with debugging off and on, rebooted my pc and phone. Definitely an after effect of reflashing.Any advice? Im searching all over currently, if i find anything ill post here
I've had something similar happen on my phone. After a flash, it started failing to detect the phone correctly.
Try disconnecting your phone from your PC, uninstall the Samsung USB driver on PC, then re-connect your phone.
It should start installing a new set of drivers for your phone and get it running again.
I would uninstall kies from the compyter and install the USB drivers only. See the link in my sig if you need them.
Personally I forego the cable and use a wireless ftp transfer app. My favorite one used to be called SwiFTP. Its now in the store just cslled FTP Server. Theres a fully functional demo you can try too.
Sent from my SGH-T999 using xda premium
DocHoliday77 said:
I would uninstall kies from the compyter and install the USB drivers only. See the link in my sig if you need them.
Personally I forego the cable and use a wireless ftp transfer app. My favorite one used to be called SwiFTP. Its now in the store just cslled FTP Server. Theres a fully functional demo you can try too.
Sent from my SGH-T999 using xda premium
Click to expand...
Click to collapse
Advice taken from both of you i now have AirDroid and will be looking up SwiFTP as soon as my phone boots.
I had just fixed the issue, upon this thread http://androidforums.com/samsung-galaxy-s3/626480-s3-charges-via-usb-but-not-recognised-pc.html
KUDOS AND CREDITS TO Nacos from xda!
"1. Uninstall any previous instance of Kies/USB driver
2. Download the latest Kies, specific to your S3.
3. Download Samsung USB drivers 1.4.6.0 (I've tried newer versions but they all failed)
4. REBOOT
5. Disconnect from internet (VERY IMPORTANT!!! - forcing Windows to install local drivers ONLY)
6. With the phone disconnected, install Kies + USB drivers downloaded in steps 2,3
7. Connect the phone and let Windows install the drivers.
8. Reestablish the internet connection. "
Also as a bonus i was told to power off my device, take out the battery, SD and SIM and insert again and reboot.
Upon all these steps phone fully detected on windows as soon as drivers installed (with internet connection disabled)
P.S. No matter if i restored from a backup created before this problem, it would not be detected thats how i knew it was a driver issue.
Okay i have seen similar posts around, and I apologize if this bothers anyone but when I post a thread asking for help, its because I've tried most solutions and have gotten nowhere. I recently bought one.of.these devices and I have to say for an old 1GHz device, its pretty darn smooth! (Got it for my girl who broke her phone. Cost $20 MINT screen, and some scuffs.on the trim believe it or not, fully functional, clean ESN)
I love for all devices in the house to be rooted and off that dreaded Gingerbread android. I have been stuck since i got it trying to use ODIN to flash CWM, and root it to flash a JB based rom. Problem is i installed the drivers, got the ODIN version required, have the CWM tar file, etc, the phone gets detected while on in ADB, normal file transfer way and so on. BUT Download Mode? Nope, i get the dreaded "Unknown Device" issue.
Now as I always read before annoying others, I read that switching the USB cable helps. I've tried 8 USB cables, and no go. 2 Samsungs (i read those are #1 NO GOs), 3 LG cables (device doesnt appear at all), and 3 non brand. No good.
I know Mobile Odin wont work, I rooted it using Framaroot.apk for now, but I need CWM for the rom flashing part.
So now that its 2013, is there really no other way other than ODIN? I tried using ROM Manager, it flashes but doesnt do a thing except boot into stock recovery (miracle no bricks or bootlooping). If I had Linux on my PC, will it get detected or its just the darn cable?
OR is there a specific USB cable brand I should go for that is guaranteed to work? I dont mind buying it just have been waiting to make sure.
Any help or advice is greatly appreciated.
Most people recommend using a BlackBerry cable
Sent from my SPH-D700 using Tapatalk 2
jeffreyjicha said:
Most people recommend using a BlackBerry cable
Sent from my SPH-D700 using Tapatalk 2
Click to expand...
Click to collapse
Thank GOSH I read your response in time! I am currently at BestBuy and was going to buy a totally different brand USB. Hopefully they have them here.
Crossvxm said:
Thank GOSH I read your response in time! I am currently at BestBuy and was going to buy a totally different brand USB. Hopefully they have them here.
Click to expand...
Click to collapse
I use this cable and have had zero issues. http://www.monoprice.com/products/p...=10303&cs_id=1030307&p_id=5458&seq=1&format=2
Well there's good news and bad.
Got an official BlackBerry USB cable.
Bad is the device is STILL not recognized.
The drivers have been properly installed, there is no updating the drivers manually, effing Windows won't let me. What the hell can I do now?
If only Mobile Odin worked, or there were other methods, I wouldn't be going thru this mess...
Like where did I go wrong?
I would swap out Windows to Linux, but I don't see how that will get the device detected.
Matter of fact I was trying to install a Linux based OS from my flash drivd, and it corrupted it. Theres 8gb Ill never see again...
Any other ideas? Will Linux pick up the device?
EDIT: This USB unlike the others BRIEFLY detects it as a USB Device, then goes back to unknown when I uninstall it thru Device Manager
Crossvxm said:
Well there's good news and bad.
Got an official BlackBerry USB cable.
Bad is the device is STILL not recognized.
The drivers have been properly installed, there is no updating the drivers manually, effing Windows won't let me. What the hell can I do now?
If only Mobile Odin worked, or there were other methods, I wouldn't be going thru this mess...
Like where did I go wrong?
I would swap out Windows to Linux, but I don't see how that will get the device detected.
Matter of fact I was trying to install a Linux based OS from my flash drivd, and it corrupted it. Theres 8gb Ill never see again...
Any other ideas? Will Linux pick up the device?
EDIT: This USB unlike the others BRIEFLY detects it as a USB Device, then goes back to unknown when I uninstall it thru Device Manager
Click to expand...
Click to collapse
Are you plugging into a port directly on the motherboard? (IE: A port on the back of the machine.) Using an emulated port or hub can cause this at times.
FYI, there are 2 drivers. One is for when the phone is fully booted in Android. The other is the driver when in download mode. Have you tried using another machine?
Sent from my Nexus 7 using Tapatalk 2
I think your issue is driver related. I had similiar issues and updated the wiki with the drivers that ended up working for me.
Sent from my SPH-D700 using xda app-developers app