Develop Bugs

[q] voltage control boots up with settings? or.....

does the voltage control apply every reboot or do i have to run the program again?

shawayne21 said:
does the voltage control apply every reboot or do i have to run the program again?
Click to expand...
Click to collapse
if you save as boot it will otherwise u will have to change it everytime after reboots..
Make sure you know that the voltage works properly on your phone before setting on boot settings...

davidrules7778 said:
if you save as boot it will otherwise u will have to change it everytime after reboots..
Make sure you know that the voltage works properly on your phone before setting on boot settings...
Click to expand...
Click to collapse
and how do i know it works properly? by it still being as stable as before it was uv?
Im running Urban Regeneration 1.1.1
my settings on the Voltage Control App are:
cfq
1200/ -25
1120/ -50
1000/ -50
800/ -75
600/ -75
400/ -75
200/ -100
100/ -100
are these safe? this is the first time i tried this

shawayne21 said:
and how do i know it works properly? by it still being as stable as before it was uv?
Im running Urban Regeneration 1.1.1
my settings on the Voltage Control App are:
cfq
1200/ -25
1120/ -50
1000/ -50
800/ -75
600/ -75
400/ -75
200/ -100
100/ -100
are these safe? this is the first time i tried this
Click to expand...
Click to collapse
well just use them for awhile and see if you get any freezes or sleep of deaths or what not and if not then set them on boot

thanks a bunch. do mines sound good though?

shawayne21 said:
thanks a bunch. do mines sound good though?
Click to expand...
Click to collapse
let me compare them to mine

davidrules7778 said:
let me compare them to mine
Click to expand...
Click to collapse
they seem to be good, btw what app u using to show those voltages like that?

shawayne21 said:
thanks a bunch. do mines sound good though?
Click to expand...
Click to collapse
You can't compare to other users' settings. Thay are different on almost every Epic. Our phones our odd that way. You have to test what works for you.
Sent from my SPH-D700 using XDA Premium App

davidrules7778 said:
they seem to be good, btw what app u using to show those voltages like that?
Click to expand...
Click to collapse
Voltage Control.

I have a problem now ... Last night, i left it on 70% .. and when i woke up, i found it dead -__- ... is this due to the voltage control? or my rom?

Probably your voltage control settings. However, to rule out other possible issues run without undervolting and replicate the situation that caused your phone to die. If it dies again something else was the problem. If it doesn't, then it was your uv setup
Sent from the communications console of the NX-01 using a universal translator

Thanks .. I uninstalled the app this morning ad am gunna see how it treats the battery tonight.

[Q] SetCPU Settings/Questions

okay, so when everyone says that 800MHz should be on "-25mV" what the hell does that mean? i want to improve my battery life to the max possible, 1st time undervolting so yeah...
mines is set to 1025mV
I need a profile for voltages for SetCPU only
Running
Calk's Rom 2.8.1 n Gunslinger 1.4.1

kj13569 said:
okay, so when everyone says that 800MHz should be on "-25mV" what the hell does that mean? i want to improve my battery life to the max possible, 1st time undervolting so yeah...
mines is set to 1025mV
I need a profile for voltages for SetCPU only
Running
Calk's Rom 2.8.1 n Gunslinger 1.4.1
Click to expand...
Click to collapse
If you're using SetCPU, you have all the tools you need. I recommend UVing -50mV at each frequency 1200 & lower. Click apply, then use your phone. If it works well enough, don't be afraid to check the "Set on Boot" boxes

nibrwr said:
If you're using SetCPU, you have all the tools you need. I recommend UVing -50mV at each frequency 1200 & lower. Click apply, then use your phone. If it works well enough, don't be afraid to check the "Set on Boot" boxes
Click to expand...
Click to collapse
appreciate your reply, may be a dumb noob statement but...
it will not let me enter "-50mV" or "-" for that matter just "50mV' and isnt 50mV way too low to be stable? i tried just "25mV" and phone froze so.... please help...
Thanks so much.
PS. it will not let me add special characters... just numbers. numbers go all the way down to "0" but not negative numbers....

If you are running calk's 2.8.1, you are already undervolted by 50mV, so no need to mess with set cpu voltages. You can however mess with the underclock settings. I for example run at 800Mhz with the conservative governor and get great battery life. However if you must mess with the undervolting in set cpu, -50Mv means 50Mv less than default. So lets say ur voltage is 1025 at 800Mhz, to undervolt it by -50 you would change it to 975 (1025-50=975). HOWEVER, as I have mentioned already, you are already undervolted -50 by default when on CALKS rom.
EDIT: To prove that you are already undervolted, here are the STOCK voltages,
1704=1500
1600=1450
1504=1400
1400=1350
1200=1275
1000=1175
800=1075
500=975
200=950
Go into setspu and you will notice your values are all 50 less than the ones listed above.

meatwadathf said:
If you are running calk's 2.8.1, you are already undervolted by 50mV, so no need to mess with set cpu voltages. You can however mess with the underclock settings. I for example run at 800Mhz with the conservative governor and get great battery life. However if you must mess with the undervolting in set cpu, -50Mv means 50Mv less than default. So lets say ur voltage is 1025 at 800Mhz, to undervolt it by -50 you would change it to 975 (1025-50=975). HOWEVER, as I have mentioned already, you are already undervolted -50 by default when on CALKS rom.
EDIT: To prove that you are already undervolted, here are the STOCK voltages,
1704=1500
1600=1450
1504=1400
1400=1350
1200=1275
1000=1175
800=1075
500=975
200=950
Go into setspu and you will notice your values are all 50 less than the ones listed above.
Click to expand...
Click to collapse
Thanks for that, I needed to be schooled. So if i'm running at 800mhz all day, why is my battery being depleted so quickly? (I get a good 12hrs per charge)
What's the lowest I can go? (stable)

kj13569 said:
Thanks for that, I needed to be schooled. So if i'm running at 800mhz all day, why is my battery being depleted so quickly? (I get a good 12hrs per charge)
Click to expand...
Click to collapse
The lowest that is recommended (atleast by Calk) is -100 so 100 less for each of all the values I listed above. However, if -100 makes ur phone slow or restart, try -75, etc...
Battery all depends on your usage. There are a few things you can try to improve it even more. First of all, flash rogue's newest kernel found here:
http://forum.xda-developers.com/showthread.php?t=1341564
Second, make sure to calibrate your battery. The easiest way is to download the Battery Calibration app from the market and follow the directions in the app (its fairly simple). Finally, make sure your governor in setcpu is set to conservative.
EDIT: Also, make sure you manage your running applications. I like to use the stock manager widget that comes with the phone. Allows you to close apps you are not currently using. And finally, you can try running the script found here:
http://forum.xda-developers.com/showthread.php?t=991276
It changes the way your phone uses resources to make it more efficient so it MIGHT also help battery life.
EDIT2: FINALLY, I know you said you're running at 800Mhz all day, but make sure you have your max set at 800 and min at 200. (you never mentioned you were underclocked before so just want you to make sure you are).

meatwadathf said:
If you are running calk's 2.8.1, you are already undervolted by 50mV, so no need to mess with set cpu voltages. You can however mess with the underclock settings. I for example run at 800Mhz with the conservative governor and get great battery life. However if you must mess with the undervolting in set cpu, -50Mv means 50Mv less than default. So lets say ur voltage is 1025 at 800Mhz, to undervolt it by -50 you would change it to 975 (1025-50=975). HOWEVER, as I have mentioned already, you are already undervolted -50 by default when on CALKS rom.
EDIT: To prove that you are already undervolted, here are the STOCK voltages,
1704=1500
1600=1450
1504=1400
1400=1350
1200=1275
1000=1175
800=1075
500=975
200=950
Go into setspu and you will notice your values are all 50 less than the ones listed above.
Click to expand...
Click to collapse
Hey meatwadath, I am running calk's 2.8.1 and went to verify, via setcpu, that I was already undervolted by -50. However, my voltages read the same as what you referenced above. Any ideas?

jasone4gt said:
Hey meatwadath, I am running calk's 2.8.1 and went to verify, via setcpu, that I was already undervolted by -50. However, my voltages read the same as what you referenced above. Any ideas?
Click to expand...
Click to collapse
Means that you are running on stock voltages. That's strange as you should be at -50 by default. Either change the values manually in setcpu, or flash the zip located here:
http://forum.xda-developers.com/attachment.php?attachmentid=845028&d=1325871602
It is Calk's -50 undervolt script.

meatwadathf said:
Means that you are running on stock voltages. That's strange as you should be at -50 by default. Either change the values manually in setcpu, or flash the zip located here:
http://forum.xda-developers.com/attachment.php?attachmentid=845028&d=1325871602
It is Calk's -50 undervolt script.
Click to expand...
Click to collapse
Thanks bro, appreciate the help. Gave you a few thanks for it...

No problem. Any time.

Ok, where is the settings to undervolt in setCPU, because I looked everywhere in the program and cannot find it. I'm probably just retarded... I'm on UnNamed, Rogue Stock EL29 kernel.

beezar said:
Ok, where is the settings to undervolt in setCPU, because I looked everywhere in the program and cannot find it. I'm probably just retarded... I'm on UnNamed, Rogue Stock EL29 kernel.
Click to expand...
Click to collapse
Setcpu- Third button from the top says voltage, then click on the different voltages listed below Apply, pull the little bar to the left to undervolt...

jasone4gt said:
Setcpu- Third button from the top says voltage, then click on the different voltages listed below Apply, pull the little bar to the left to undervolt...
Click to expand...
Click to collapse
Ok, I don't have that button, only got "Main, Profiles, Advanced, Info, About"
I think it's because I'm on a stock kernel; looked it up and undervolting on setCPU only runs on certain kernels apparently. Not sure though.

beezar said:
Ok, I don't have that button, only got "Main, Profiles, Advanced, Info, About"
I think it's because I'm on a stock kernel; looked it up and undervolting on setCPU only runs on certain kernels apparently. Not sure though.
Click to expand...
Click to collapse
Thats probably it. WTH are you doin on stock?!? Get on gunslinger right now!

meatwadathf said:
Thats probably it. WTH are you doin on stock?!? Get on gunslinger right now!
Click to expand...
Click to collapse
I concur

Set CPU
For some reason setcpu isn't really helping out my battery life. When I use it I get the same results as if I wasn't using it.

dorejades said:
For some reason setcpu isn't really helping out my battery life. When I use it I get the same results as if I wasn't using it.
Click to expand...
Click to collapse
You're probably expecting too much. Its not gonna make your battery last for 2 days without a charge. It has to help if you are using it correctly.
There is just no way around it. Lower clockspeeds=less battery drain.

meatwadathf said:
The lowest that is recommended (atleast by Calk) is -100 so 100 less for each of all the values I listed above. However, if -100 makes ur phone slow or restart, try -75, etc...
Battery all depends on your usage. There are a few things you can try to improve it even more. First of all, flash rogue's newest kernel found here:
http://forum.xda-developers.com/showthread.php?t=1341564
Second, make sure to calibrate your battery. The easiest way is to download the Battery Calibration app from the market and follow the directions in the app (its fairly simple). Finally, make sure your governor in setcpu is set to conservative.
EDIT: Also, make sure you manage your running applications. I like to use the stock manager widget that comes with the phone. Allows you to close apps you are not currently using. And finally, you can try running the script found here:
http://forum.xda-developers.com/showthread.php?t=991276
It changes the way your phone uses resources to make it more efficient so it MIGHT also help battery life.
EDIT2: FINALLY, I know you said you're running at 800Mhz all day, but make sure you have your max set at 800 and min at 200. (you never mentioned you were underclocked before so just want you to make sure you are).
Click to expand...
Click to collapse
I just would like to say thanks so much for all the info and advice. You're Awesome!

beezar said:
Ok, I don't have that button, only got "Main, Profiles, Advanced, Info, About"
I think it's because I'm on a stock kernel; looked it up and undervolting on setCPU only runs on certain kernels apparently. Not sure though.
Click to expand...
Click to collapse
ditto. I'm on blazerROM v3.7. I think its using the stock kernel as well. I didn't have an undervolt tab. I did set up profiles similar to calks script:
100% - 85: 1200/200
84% - 35: 1000/200
34% and lower: 800/200
screen off: 800/200
The question is, do I need to undervolt? Or could I still be getting the same results if i'm on the stock kernel with this profile set up? I just set this up last night.

I was in the same boat... had Calk's v2.8.1 ROM with stock kernel... updated kernel to Gunslingers.. we will see how it goes... Noob myself, I thought Calk's ROM would take care of everything....
This leads me to think what else am I missing?? Anything I need to do/install/tweak??...
Calk's v2.8.1 with Gunslinger 1.4.1.
Thanks much!!
meatwadathf said:
Thats probably it. WTH are you doin on stock?!? Get on gunslinger right now!
Click to expand...
Click to collapse

Overclocking Instability

Hey I just bought a 32 GB Gnex and got it yesterday but it seems to be unstable at anything above the stock max frequency of 1230 MHz. I've tried Paranoid Android and last night's CM10 nightly and they would both freeze and immediately reboot upon setting it to 1305 MHz. I then flashed the Zen kernel on top of CM10 and I like that it can go up to 1.8 GHz but whenever I set anything beyond 1.23 GHz it starts to lag for about 1-3 seconds. When I knock it back down to 1.23 GHz everything is fine again.
This is the first OMAP device I have since I had the OG Droid back in 09, I loved how they were extremely overclockable and I'm going to be pretty sad if mine has to stay at stock speeds. I've tried using JRummy's ROM Toolbox Pro and the built in Performance settings to try and set the frequencies but it doesn't seem to make a difference on which one I use. I've been using the OnDemand and Interactive(x) Governors.
Is this a known problem or am I alone on this?

some CPUs have a higher tolerance than others for overclocking. looks like you got one of the super low tolerance ones.

I hope that's not the case :-/

brando56894 said:
Hey I just bought a 32 GB Gnex and got it yesterday but it seems to be unstable at anything above the stock max frequency of 1230 MHz. I've tried Paranoid Android and last night's CM10 nightly and they would both freeze and immediately reboot upon setting it to 1305 MHz. I then flashed the Zen kernel on top of CM10 and I like that it can go up to 1.8 GHz but whenever I set anything beyond 1.23 GHz it starts to lag for about 1-3 seconds. When I knock it back down to 1.23 GHz everything is fine again.
This is the first OMAP device I have since I had the OG Droid back in 09, I loved how they were extremely overclockable and I'm going to be pretty sad if mine has to stay at stock speeds. I've tried using JRummy's ROM Toolbox Pro and the built in Performance settings to try and set the frequencies but it doesn't seem to make a difference on which one I use. I've been using the OnDemand and Interactive(x) Governors.
Is this a known problem or am I alone on this?
Click to expand...
Click to collapse
you need to disable smart reflex mpu if you want to overclock. smart reflex doesnt know overclocking, so it sets your voltages to low for an overclocked cpu. thus, instant instability.
to disable smart reflex manually, use a terminal emulator. type su(press enter) then type these 3 lines and press enter after each..
*
echo "0" > /sys/kernel/debug/smartreflex/sr_mpu/autocomp
0 to disable, 1 to enable.
btw, some cpu control apps give you options to disable/enable smart reflex.

What three lines? I only see one...
I echo'd a value of "0" to the file but it was still unstable at 1.8 GHz, haven't tried lower frequencies yet, I don't have to reboot after setting the value, correct?
edit: still unstable at 1.42 GHz, also what apps would those be that allow this? Antutu CPU Master Pro only has an option to disable PerfLock.

the way to overclock is to keep moving in small increments upward and burn testing them to check for stability. Don't go straight for a 50% overclock. move up and find your threashold, and when you do start tweaking to see if you can slowly creep beyond that

brando56894 said:
What three lines? I only see one...
I echo'd a value of "0" to the file but it was still unstable at 1.8 GHz, haven't tried lower frequencies yet, I don't have to reboot after setting the value, correct?
Click to expand...
Click to collapse
The 3 lines would be:
Code:
echo "0" > /sys/kernel/debug/smartreflex/sr_mpu/autocomp
echo "0" > /sys/kernel/debug/smartreflex/sr_core/autocomp
echo "0" > /sys/kernel/debug/smartreflex/sr_iva/autocomp
Frankly, though, don't expect 1.8GHz to be stable.

Your particular device's components might not hold it together with that oc.
Sent from my i9250

Darunion said:
the way to overclock is to keep moving in small increments upward and burn testing them to check for stability. Don't go straight for a 50% overclock. move up and find your threashold, and when you do start tweaking to see if you can slowly creep beyond that
Click to expand...
Click to collapse
Yea I know (I used to OC the CPU on my PC), I just wanted to go for something big to see if it could handle it.
Edit: seems to be stable at 1.4 GHz, I'm going to keep increasing it to see what the limit is. I'm assuming i'd have to turn off smartreflex on each boot so I should probably put it in a script in /etc/init.d correct?

brando56894 said:
What three lines? I only see one...
I echo'd a value of "0" to the file but it was still unstable at 1.8 GHz, haven't tried lower frequencies yet, I don't have to reboot after setting the value, correct?
edit: still unstable at 1.42 GHz, also what apps would those be that allow this? Antutu CPU Master Pro only has an option to disable PerfLock.
Click to expand...
Click to collapse
the trinity kernel toolbox lets you disable/enable smart reflex. plus, extremely few gnex will oc to 1.8ghz. and on top of that, to oc even to 1.4 or 1.5ghz, youll need to adjust your voltages to get yourself stable. every device likes different voltages.

I had it stable at 1.4, 1.5, 1.6, 1.7 and told my GF that I could OC it now (because I told her before that I didn't think I could) ...and then it froze rock solid lol

brando56894 said:
I had it stable at 1.4, 1.5, 1.6, 1.7 and told my GF that I could OC it now (because I told her before that I didn't think I could) ...and then it froze rock solid lol
Click to expand...
Click to collapse
i can oc my gnex(using trinity kernel) to 1.803ghz.. but to use stable for every day, 1.689ghz is a good speed for my device. a majority of devices wont even oc that high and stable. stable being the key word.

brando56894 said:
I had it stable at 1.4, 1.5, 1.6, 1.7 and told my GF that I could OC it now (because I told her before that I didn't think I could) ...and then it froze rock solid lol
Click to expand...
Click to collapse
I'd find it surprising that you got 4 different overclock levels stable in 30 minutes. There's a difference between "it boots", "it boots and runs some apps", and "stable".

brando56894 said:
I had it stable at 1.4, 1.5, 1.6, 1.7 and told my GF that I could OC it now (because I told her before that I didn't think I could) ...and then it froze rock solid lol
Click to expand...
Click to collapse
Is she impressed by your turbo-nerd status?! :silly:

Haha she was an iSheep but I made her get an SGS3 and I turned her into an Android geek, now she flashes ROMs on her own lol
Cilraaz said:
I'd find it surprising that you got 4 different overclock levels stable in 30 minutes. There's a difference between "it boots", "it boots and runs some apps", and "stable".
Click to expand...
Click to collapse
Yea it wasn't stable in the true sense of the word, I meant it just didn't freeze every minute or so.
Sent from my Galaxy Nexus using Tapatalk 2

I'm running the 11/4 build of Paranoid Android with v3.0.51-ZenSeries v4 Tuna and I having problems setting CPU frequencies via Trinity Kernel Toolbox. The frequency will stick until I switch to another app, then when I come back to the app it will be at the stock max frequency. I am also unable to use the built in frequency tuner when using TKT.
I've tried stress testing it with stability test and even when the frequencies will stick in TKT (ex. 1.4 GHz) Stability Test will report that its at 1.1 GHz. WTF is going on here? I have all three of the smart reflex values disabled.

brando56894 said:
I'm running the 11/4 build of Paranoid Android with v3.0.51-ZenSeries v4 Tuna and I having problems setting CPU frequencies via Trinity Kernel Toolbox. The frequency will stick until I switch to another app, then when I come back to the app it will be at the stock max frequency. I am also unable to use the built in frequency tuner when using TKT.
I've tried stress testing it with stability test and even when the frequencies will stick in TKT (ex. 1.4 GHz) Stability Test will report that its at 1.1 GHz. WTF is going on here? I have all three of the smart reflex values disabled.
Click to expand...
Click to collapse
dont use PA cpu settings. do you have any other cpu control apps installed? make sure theres nothing enabled in PA cpu settings, nothing. then reboot. wait 2-3 after bootup then open tkt and try using it. is the problem still there?

It seems to be sticking now for the moment, but I haven't had anything in PA CPU settings before I rebooted anyway. I do not have any other CPU OC apps installed either. Stability test is reporting the correct frequency also. Thanks.

brando56894 said:
It seems to be sticking now for the moment, but I haven't had anything in PA CPU settings before I rebooted anyway. I do not have any other CPU OC apps installed either. Stability test is reporting the correct frequency also. Thanks.
Click to expand...
Click to collapse
sweet.
if you were checking before 3 minutes after bootup, then that was the issue. whatever it was, lets hope it doesnt come back.

I was setting the values after the phone had been up for hours, idk what the problem was :-\q

Unable to stick at lower CPU freq

I am currently using this rom http://forum.xda-developers.com/showthread.php?t=2306650 , but i doubt its the rom fault.
Using the MIUI settings, Antutu CPU master, or ROM ToolBox, applying a lower CPU max freq will not stick.
Ex: The max is 1890mhz, but i want it at 1566mhz for the max. After turning the phone off and on, the max CPU freq. goes back to the original 1890mhz. With a reboot, it sticks, half the time.
What do i do? Please reply ASAP, my S4 gets hot while playing games so i like to underclock it.

With many years of experience, the best thing I can tell you is to not place a MHz cap that is too high. Your phone can potentially be a potato if you're not careful.
Sent from my GT-I9505G using Tapatalk

HenryTheUnicorn said:
I am currently using this rom http://forum.xda-developers.com/showthread.php?t=2306650 , but i doubt its the rom fault.
Using the MIUI settings, Antutu CPU master, or ROM ToolBox, applying a lower CPU max freq will not stick.
Ex: The max is 1890mhz, but i want it at 1566mhz for the max. After turning the phone off and on, the max CPU freq. goes back to the original 1890mhz. With a reboot, it sticks, half the time.
What do i do? Please reply ASAP, my S4 gets hot while playing games so i like to underclock it.
Click to expand...
Click to collapse
Download CPU controller app from the market. It will reset your CPU upon screen on.
Sent from my SGH-M919 using Tapatalk

elesbb said:
Download CPU controller app from the market. It will reset your CPU upon screen on.
Sent from my SGH-M919 using Tapatalk
Click to expand...
Click to collapse
Everything I've ussed applies settings on boot, but it wont frickin work sometimes.

HenryTheUnicorn said:
Everything I've ussed applies settings on boot, but it wont frickin work sometimes.
Click to expand...
Click to collapse
SetCPU has different profiles to configure. And which ROM are you on? There might be an init.d script adjusting the frequencies. SetCPU will apply them AFTER any init.d scripts are ran so that should fix it. I loved SetCPU till ktoonsez made his own app.

elesbb said:
SetCPU has different profiles to configure. And which ROM are you on? There might be an init.d script adjusting the frequencies. SetCPU will apply them AFTER any init.d scripts are ran so that should fix it. I loved SetCPU till ktoonsez made his own app.
Click to expand...
Click to collapse
the rom i am on is in the first post.
How do i check the script if it is?
Meh, till i figure that out, time to use SetCPU. I MUCH prefer Antutu Cpu Master Pro, a profile for overheating? Hell yes, i set mine to 1.2ghz at 105 degrees F. and 1.5/1.6ghz when its normal. Helped ALOT

HenryTheUnicorn said:
the rom i am on is in the first post.
How do i check the script if it is?
Meh, till i figure that out, time to use SetCPU. I MUCH prefer Antutu Cpu Master Pro, a profile for overheating? Hell yes, i set mine to 1.2ghz at 105 degrees F. and 1.5/1.6ghz when its normal. Helped ALOT
Click to expand...
Click to collapse
I believe setCPU has that profile as well
Sent from my SGH-M919 using Tapatalk

elesbb said:
I believe setCPU has that profile as well
Sent from my SGH-M919 using Tapatalk
Click to expand...
Click to collapse
Oh darn. It worked for a bit. Now instead of going back to normal max frequency after a reboot or boot up, it does it when I'm using the phone.
Does PAC ROM have this issue? If not, I'll use pac rom instead. Or it may be a kernel problem? Idk much about android stuff

HenryTheUnicorn said:
Oh darn. It worked for a bit. Now instead of going back to normal max frequency after a reboot or boot up, it does it when I'm using the phone.
Does PAC ROM have this issue? If not, I'll use pac rom instead. Or it may be a kernel problem? Idk much about android stuff
Click to expand...
Click to collapse
Sounds like the kernel is overriding certain things in different scenarios. I'd try a different kernel.

why cant i underclock the CPU?

Every time I try to underclock the CPU as soon as I leave the app the sliders go back to where they were originally. Even after applying on boot. Am I doing something wrong?

BakedOnSomeSour said:
Every time I try to underclock the CPU as soon as I leave the app the sliders go back to where they were originally. Even after applying on boot. Am I doing something wrong?
Click to expand...
Click to collapse
Since you've given virtually no information, I will assume that your phone is unrooted and/or running with the stock kernel. You will need to address both to be able to underclock.

Because underclocking is silly.

Wakamatsu said:
Since you've given virtually no information, I will assume that your phone is unrooted and/or running with the stock kernel. You will need to address both to be able to underclock.
Click to expand...
Click to collapse
I am rooted and running elementalX kernel

BakedOnSomeSour said:
I am rooted and running elementalX kernel
Click to expand...
Click to collapse
I'm not running EX. Does it use init.d or config script? Those may overwrite whatever method you're using to underclock at boot.

Underclocking-saving battery
Is a BIG LYE
CPU will not use full power (max freq) when not need.
Dont forget what is Mhz (how MUCH things CPU can do in what TIME) the only deffrent bettwen underclocked and overclocked is TIME.312Mhz will do something in 5 mins,but 2 Ghz will do it in 1 second. It just do faster,but battery use is same,count yourself

1. You warmed up a dusty thread.
2. Battery-work isn't simply product of time and frequency: longer low tasks eats fewer capacity than shorter peak ones.