Tonnes of us have problems with the USB board.
I ordered an OEM one and I'm gonna get it next month, but in the mean time, is there a guide for installing the board onto your phone?
I have successfully opened up my phone, exposing all it's inner glory. I just don't know how to remove the old usb board.
Do I solder off the connections and solder back on the new board?
Related
Hello all.
I dropped my phone pretty hard the other day. I dropped it many times before so I didn't think there would be any damage besides that the battery popped out.
Once I got home and wanted to charge my Artemis I noticed that my USB connector is gone!
Well, I found myself a spare one on eBay, but as I looked at the connections on the circuit board of my Artemis I started to doubt the possibility to put another USB connector in there.
Some pins seem to be damaged real bad but not all of them, and then again I only want to be able to charge my phone and will not use the USB connector for syncing or using a headphone.
Can someone take a look at the picture I took and see if its still possible to attach a new USB connector to my Artemis and if it will at least be able to charge the battery?
Photo of circuit board:
Many thanks!
Repair of the USB mini port
Hey,
Could you send a picture with more sharpness, because i can't see it that well.
I already see that you have been soldering on top (close to your serial number).
Kind Regards
Bramatus
As long as you have got the correct connector then the way you do it is to remove the solder that is on the pads on the board and apply solder PASTE to the pins of the connector, then with a very COOL soldering iron gently touch the pins just long enough to flow the solder on.
A few month's ago I'd ordered a LCD screen replacement for my incredible, and so when I got back from work o immediately took out the LCD from the package and started taking out my old broken. For me it was my first time experience replacing an LCD phone screen, anyways back to what I was going to say was when I unplugged the connector for the screen and the motherboard itself, after attempt to plug the connectors back together; the display connector plugged in perfect while the connector for the motherboard didn't do so well. The white piece that covers the PCB Connector, it tears a little bit off and I'd tried to power on the phone, meanwhile it didn't I tried again and things got worst. So I search online for a PCB Connector and see one, so I decided to and try to rip off the PCB Connector and plan to order the PCB Connector. So the part to attempt ripping off the PCB Connector didn't go so well, and stop there before things got worst. Any suggestions how I can replace that? I can't just leave my phone in my room and have to cover in dust. I need my phone back, how can I fix these? I know this thread seems long but I tries but it details for you guys.
Seems my USB port needs replacing, I first thought I may have had some lint or something inside there as it wouldn't charge but after checking with a flashlight one of the pins had bent completely.
The only thing I can find for the original desire is eBay ID 380759842289
Can anyone confirm if this is right, or where I could purchase one from the UK.
Are they hard to replace? Would it just be the case of removing the 2 lower t5 screws, taking the antenna out of way and then what? Are they soldered on or ribbon cable?
Cheers
I had a similar problem, my device couldn't connect via usb but it was able to charge, so my first thought was the same as yours (about the lint). I tried to clean it and I found something like a little wire which was out of its place.
I ordered a usb port (about 1.50 euros) for that model and I followed this guide on youtube to disassemble the device /watch?v=8sYB_AM_jHE
You have to dissolder the old one and then solder the new which is a little bit tricky. It Worked!
For the replacement parts you can search on ebay for htc desire g7 its the same or use google you will find a bunch of them.
This person posted this about kindle fire not working
At first my Fire wouldn't charge unless it was placed in a particular way, then it stopped altogether. I pronounced it dead, and left it stowed away for a few months, but then decided to try and fix it. I think this guide may be useful for anyone who wants to fix a kindle with dead charging. Note that you may damage your kindle in the process so if you are still under warranty, use it.
1. Take off the back cover. You may need to use a guitar pick or something similar.
2. Take off the two battery leads. One has a locking mechanism which needs to be lifted before the ribbon cable can be taken out.
3. Take out all screws connected motherboard to rest of device. There are connections underneath the board so be careful when lifting it.
4. When I lifted it, I found the USB connector had broken off the entire board (if it was even attached in the first place) and this was obviously causing the problems, as the USB connector could now only connect to the motherboard if pressure was applied so that it was being held on somehow by it. To fix this, I could have tried to solder the tiny USB connections onto the board, but instead I used a different way which is working perfectly for many weeks now.
5. Get a rubber band and tie a not in it numerous times until the knot is about 3-4mm thick. Cut off remaining rubber band and superglue the knot onto the bottom side of the USB connector (the side that faces the display when assembled). Then insert the USB connector into it's little holder under the board, with the rubber band firm beneath it and replace the motherboard. Redo all the screws, reconnect any connectors you've disconnected (you may have had to disconnect some to remove/move the motherboard - always undo battery cables before you work on the innards of any device).
6. If you've done this correctly, the round rubber band knot should press the USB connector continuously on to the board. Test using your stock charger before you put it back together because the back cover is pretty hard to get off.
7. Replace the back cover and enjoy!
Notes: My rubber band knot was actually a little too large, which meant that to connect the USB plug I had to press the kindle together to insert the cable, but charging is reliable and working so far, so I'm happy about that.
If you found this post helpful, please click the Thanks button!
And I think he's long gone it's an old post and I need help what does he mean by connect the rubber band to the usb where do you put the rubber band where do you super glue it the motherboard kindle or the usb and what does he mean by tie it how do you tie a rubber band
Now the pixel 2 xl support ended i am trying to root and install custom rom. But my device is not debugging...
When connected to pc only charging.. no usb options.
I can connect the usb drive and other peripherals
Usb debugging enabled in developer option.
Tried different cables.. different port.. different pc..
Is it usb c port problem or some software problem?
Any help advice!!!
Thanks in advance
I've got the same problem. Many have said they had success with different USB cables, but I've tried dozens without any luck.
I'm thinking hardware at this point, since I finally got the last OTA update and it made no difference.
I'll order the internal USB replacement part off ebay and see if it makes a difference.
I just replaced the internal USB assembly and nothing has changed. The old connector was definitely worn though.
I'll go back to trying more cables and ports. I ordered a cable that another poster claimed worked for them, but I had no luck with it.
For anyone wanting to replace their USB ass'y, here's what I learned from doing it. The service manual on ifixit is a good guide but leaves out a couple of important steps.
Heat is your friend. I used a clothes iron adjusted to 160F. The phone dissipates heat quickly so you may need to heat it several times. Place a towel over the screen and set the iron on it. I used guitar picks to pry up the screen and keep it separated while I heated the other sides.
The screen cable connection covers are hard to remove and you'll probably need a to use a metal spudger.
Heat the back of the phone to help remove the loudspeaker ass'y without damaging it, and again to remove the old cable ass'y.
The replacement ass'y I got had adhesive applied for the center of the cable, but not the adhesive foam pad under the antenna connector, so heat and scrape between the pad and phone body to remove it intact for reuse.
My old antenna connector partially came off in the white antenna connector and it was very hard to see what was wrong even under strong magnification.
You'll need a new screen adhesive sheet to reattach the screen securely.
Both parts came from a seller on ebay. Dougsgadgets was the only one that had both parts in stock. I think I paid $11 and they shipped quickly.
Good luck!