You may also call this reversed USB tether.
This might come in handy if you're near a computer (Win XP/Win7) and there's no Wifi to connect to etc..
So after some research and trying I've found some information on how to do this.
Requirements:
* Android 2.2 (or an older version with a root tethering app)
* ADB from Android SDK, or a rooted Android 2.2 with terminal in root mode
STEP 1:
Install USB drivers from Android SDK.
STEP 2:
Connect USB cable and activate USB Tethering.
You should see a new network interface. (On XP you might need to install the RNDIS driver manually, see below)
If you're also missing RNDIS driver on Win7, look here.
Win XP manual driver install Android USB Ethernet/RNDIS: (You can skip this if you're on Win 7)
1. Download the following configuration file inside the *.zip attached to this post (tetherxp.inf) to your Windows XP computer.
2. Use the USB cable that came with your phone to connect your phone to your computer.
3. On the Android phone, press Home > Menu > Settings to open the Settings application.
4. Press Wireless & networks > Tethering & portable hotspot.
5. Check USB tethering.
6. When Windows XP’s New Hardware Wizard opens, select No, not at this time and click Next.
7. Select Install from a list or specific location and click Next.
8. Click Browse to browse to the directory where you installed the configuration file you downloaded in Step 1 and click Next. Windows XP uses the configuration file to configure itself to support USB tethering with the Android phone. (This might take a while)
9. When Windows XP finishes installing the software for Android USB Ethernet/RNDIS, click Finish.
STEP 3:
Bridge the 2 network interfaces.
STEP 4:
Setup usb0 interface of your phone. You have to options:
1. From your computer, execute:
./adb shell netcfg usb0 dhcp
2. Or in a root terminal on your phone, type:
su
netcfg usb0 dhcp
You should now be able to connect to Internet on your phone using your computer's Internet connection.
Try to do a ping www.google.com to be sure.
STEP 5:
To shut down the reverse-tethering, first unbridge interfaces on your computer:
sudo ifconfig eth0 down
sudo ifconfig usb0 down
sudo ifconfig br0 down
sudo brctl delbr br0
sudo ifconfig eth0 up
sudo dhclient eth0
Then on your phone, uncheck the USB Tethering option.
Quote...
It is working now. After setting up ICS type in console emulator on your phone:
ifconfig usb1 192.168.2.2 netmask 255.255.255.0 up
route add default gw 192.168.2.1 dev usb0
iptables -F
iptables -F -t nat
setprop net.dns1 8.8.8.8
setprop "net.gprs.http-proxy" ""
Click to expand...
Click to collapse
Hope this helps some one who wants this to the right direction.
And maybe we're able to create an app to do this all automated.
Known issues but does not apply to all users:
1. Internet in browser application does not work.
2. Can't ping domain name.
For a little more info check out the sources, this includes the Linux version too.
Sources: Google android, Mycila
Nice info
Going to post a link on the hero forum where someone was wanting to do this. I wonder if this will work on a froyo hero too...
it would be cool if one of the devs could write a small app to switch this on n off great find tho shoemeistah
Thank you for the guide, It worked fine. There are several things not working though:
- can't download apps from market, they stuck on "downloading"
- my google account don't sync
- other apps don't update themselves. For example my twitter app won't show any new tweets until I open it and manually press "refresh"
I searched for this long time ago, even created a thread about it awhile back, didnt have luck like you did though
I gave up on it eventually, it would be nice to make an app out of it.
mind asking how did you confirm the net to be working on browser? by pinging google.com?
since i saw the last line you put "Internet in browser application does not work."
You can do that in the terminal
[U][B] Internet connection on your Android phone via your PC [/B][/U]
I think I found the best solution. Check it out connectify.me
I wanted to use my PC wired internet & I was astonished that this wasn't available in my HTC Desire & 1st Android device!. I looked over the net, I found many options but most asked for a rooted device! I didn't want to root my brand new Desire.
Connectify is an easy to use software router for Windows 7 computers. After downloading and installing the lightweight application, Connectify utilizes your computers' built in Wi-Fi card to wirelessly share any available Internet connection: a cable modem, a cellular card, or even another Wi-Fi network. Other Wi-Fi enabled devices including laptops, smart phones, music players, and gaming systems can see and join your Connectify hotspot just like any other Wi-Fi access point and are kept safe and secure by password-protected WPA2 Encryption.
I tried it & it's working perfectly for me .. It's a free app.
-----------
Phone: HTC Desire (SIM Free)
Type: Desire
Build: HTC Desire 2.2, 2.10 (kernel: htc 2.6.32.15)
Baseband: 5.09.05.30
Network: UMTS auto (EGY)
By me it didn't work. Using OpenDesire with Froyo 2.2
So I made it work, by edititng the .inf file.
Here the file for USB\VID_0BB4&PID_0C02.
For all which still have a problem(USB TETHERING ON DEVICE MUST BE ACTIVE, ALSO THE IDs DIFFERS BETWEEN CONNECTED WITH ADB OR NOT), go into the device manager -> open the device -> goto tab details -> choose device id
look at it, you see somewhere vid_XXXX and further pid_XXXX
open my file -> goto line 31 -> change vid_YYYY and pid_YYYY with what you see in your device dialog. the same you do on line 35. be careful with 0 or o.
Regards
Ralph
I am also using connectify, easy to install, set it up, connect with Desire, anything works fine.
Thanks GhostOfTheNet.
chrismast said:
I am also using connectify, easy to install, set it up, connect with Desire, anything works fine.
Click to expand...
Click to collapse
I appreciate the recommendations for other solutions.
But as you can see this thread is for a internet solution at places where is no Wifi available.
So please keep it on topic, thanks!
browser & webviews
Any idea why browser won't work?
I'm interested in testing against internal sites (of course no WAP here.. cuz they be scared i guess).. both Browser and embedded webviews.
connectify great program.works fine
its a default feature in hd roms but that doesnt work in all programs
Connectify doesn't work correctly with my Galaxy 5. It keeps connected for a short time then disconnects and then, connects again, connect, disconnect...
Does anyone know how to fix it?
Thanks Man
plz make a video tutroial of this
its difficult to under stand
does it actualy work?? anyone tried this and actualy worked??? just a simple yes or no.
thanks
small proble plz solve it
hi
I have a small problem in it when my device is not in usb tethering mode
i can see it in my adb devices
as soon as is start usbtethering it say no device found
plz help me
thanks a lot !!!
realy nice guide! Thanks!
As stated in the topic I'm looking for a rom with working (!!) VPN support.
I currently have cm7.0.3 installed and can't connect to my VPN via PPTP or OpenVPN. Actually that is not correct... The icon in the statusbar states that I'm connected but no data will get through. I.e. doing a 'ping google.com' from the terminal emulator gives me an 'unable to resolve ...' error. same with any url in the browser and so on (no data connection).
one additional detail: via pptp i have to use encrypted connection ...
thanks for your time reading
Ok, i found this tutorial.
ott.net/knowledge/htc-desire-adhoc/
Installed apk and trying to terminal adb shell command and getting error
abd: not found
what is wrong?
this terminal i runned from phone not from pc..
You have to run adb from pc. A guide for installing it can be found in my signature.
TouchPaled from Oxygen with Transparent XDA App
I started adb shell and when enter:
insmod /system/lib/modules/bcm4329.ko
I have this error:
insmod: init_module '/system/lib/modules/bcm4329.ko' failed (Operation not permitted)
atlantisu21 said:
I started adb shell and when enter:
insmod /system/lib/modules/bcm4329.ko
I have this error:
insmod: init_module '/system/lib/modules/bcm4329.ko' failed (Operation not permitted)
Click to expand...
Click to collapse
I have spent some time yesterday trying the exact same thing, I didn't succeed.
For your question:
Try using the command "su" before starting insmod.
Also remember to assign execute permissions to iwconfig, else it will not work either!
I probably did something wrong (or it just doesn't work on my ROM (I'm on redux2)) because i couldnt get it to work.
Also the app ad-hoc (follow the links on his page i think) fails for me. Wifi will go to error state and only reboot makes it work again.
If you succeed please tell us how you did it because I'm veeery interested!
Doesn't work with su command...
I trying to change bcm4329.ko permission with root explorer but nothing happening.
Maybe this is the problem?
And where is located iwconfig file?
Can I change file permission from adb shell and how?
Finaly WORKS!!!!!!!!!!!!!!
Because, I cant enable ad hoc on my Desire (I try many ways and nothinhg...),
I found another way to share wifi internet from pc to android phone.
This is my way:
Download VirtualRouter
Download fresh wifi drivers for Windows 7 64bit/32bit
Disable IP6 (if you have Windows 7 64bit)
After install VirtualRouter, reset your PC and VirtualRouter will start with your Windows in system tray.
In Network Connections, enable Microsoft Virtual WiFi Miniport Adapter if disabled.
Go to Local Area Connection (your default internet connection), properties -> sharing and check all box. Select home network connection -> Microsoft Virtual WiFi Miniport Adapter or Wireless Network Connection 2.
Run cmd as admin and type this:
netsh wlan set hostednetwork mode=allow ssid=Test key=password
netsh wlan start hostednetwork
VR automaticly write ssid and key and starting virtual network.
Desire CAN SEE this network, and you CAN CONNECT!
If you have problems go here.
atlantisu21 said:
Finaly WORKS!!!!!!!!!!!!!!
Because, I cant enable ad hoc on my Desire (I try many ways and nothinhg...),
I found another way to share wifi internet from pc to android phone.
[
Click to expand...
Click to collapse
I work in the same way (with connectify)>
Too bad you couldn't get ad-hoc to work, i would like to have that solution, it is more elegant.
Any one know how to use adb over bluetooth in this device ??
I tried 'pand' command from terminal and this doesn't work.
impossible...
try this, for linux pc.
http://fomori.org/blog/blog/2011/12/05/android-adb-over-bluetooth/
nfs1mw said:
try this, for linux pc.
http://fomori.org/blog/blog/2011/12/05/android-adb-over-bluetooth/
Click to expand...
Click to collapse
I already tried this but didn't work
pand gave some error "Failed to open control socket: Address family not supported.........."
then I thought this error may be due to lack of bluetooth module.so I compiled "bluetooth.ko" and loaded.
then the error disappeared but the thing didn't worked..
I think my bluetooth device is not detected by the module because '/sys/class/bluetooth' directory was empty
So still now i am seeking for a solution....
harish2704 said:
I already tried this but didn't work
pand gave some error "Failed to open control socket: Address family not supported.........."
then I thought this error may be due to lack of bluetooth module.so I compiled "bluetooth.ko" and loaded.
then the error disappeared but the thing didn't worked..
I think my bluetooth device is not detected by the module because '/sys/class/bluetooth' directory was empty
So still now i am seeking for a solution....
Click to expand...
Click to collapse
Well it actually is not impossible. I already had it working.
But your phone shouldn't have any issues with BLUETOOTH PAN profile. If having any issues maybe don't expect this to work. And it need not have mobile internet for both phone or PC. Its just phone-to-pc direct connection, no need for internet access point. Lets think there is no mobile internet enabled for the below HOW-to.
Ok here u go. Pair your phone and PC. Initiate BT PAN connection from PC to phone (right click on bluetooth device and select connect-via-access-point). This creates a local connection. Now u need to know local IP address on phone side. Install terminal emulator application and issue the command "netcfg" which lists all connections active. Note the IP address of the connection bnep0 (say ww.xx.yy.zz)
Now open your PC Command prompt and type the command
adb connect ww.xx.yy.zz:5555
it says connected. Enjoy.
Same goes for wireless connection through LOCAL WIFI (WLAN) without internet access point.
Lets think mobile internet is off.
Turn on the portable Wifi Hotspot on the android device and make ur PC to connect to that hotspot. Note down the local ip address of the connection. Then open pc command prompt and type same command as above
adb connect ww.xx.yy.zz:5555
connected . enjoy.
IMPORTANT: First of all u need to enable ADB OVER NETWORK option in phone. This option is present in latest roms like cm7.2 or cm9 or ics roms. If this option is not available u need to find terminal alternatives for this.
Noob here.
Is there any detail guide to do this ???
So, here it goes.
My goal is to connect to a network using certain MAC address. Wanted network is marked with "open" and I know that it allows access only to certain devices (according to MAC) on which the administrator have gave a permission to. Once your MAC passes the verification, device gets connected to the network and then I'm asked to enter username and password through WEB browser (well known for me, because it is a procedure that I do on my other device, as well as all my colleagues do).
For example, I was allowed to provide one personal MAC address to administrator to connect to this network. I would like to set the MAC address of my other personal device and set it on my I9195 so that I can access the same network.
So, what have I done so far: I9195 is rooted, it has Android 4.2.2 on it and Busybox installed. I have changed MAC on it using following apps: MacChanger (blue WIFI logo), MAC Address Ghost (green ghost logo), using Android Terminal Emulator commands and via MAC Spoofer (black circle with green text logo). What can I conclude: As soon as superuser has granted the access to these apps, all of them manage to change the MAC. I've done the verification using Terminal Emulator. I also have to add that the MAC remains original if viewed from WIFI advanced menu BUT this shouldn't be an issue because:
1.) Colleague of mine is using his S4 (rooted etc.), while using MAC Address Ghost that does not change the original address (viewed from WIFI advanced menu) but he manages to make a spoof (verified from the Android Terminal Emulator, as all of this apps actually do) and he manages to connect without any problems in the same way as I connect with another device that I have!
2.) I had time to make a small test at home which put a light on the idea that the problem should be focused on the Samsung (and not on the router, especially because I am unable to modify anything on the router on this facility, not even restarting it). My home network works in a similar way as the network that we are discussing about. My S4 Mini has been included in it with his original MAC and it connects to the network without any problems. My other device is also included to the network using its MAC (the one that I am using for spoofing). My other device is turned OFF, router has been reset and I am normally accessing the network with S4 Mini. Then I run the MAC Address Ghost to spoof the MAC on my S4 Mini. In that moment, I have lost the connection that I had which means that the MAC spoofer actually did something. I tried to reconnect to the network but then I am asked to enter the password for my network. I have checked and re-checked it many times, tried to forget the network and doing it all over again but it does not accept the CORRECT password. Changing my MAC back to the original one connects S4 Mini back to the network, while accepting the password immediately.
Problem is represented in a way that it either says “saved” and does not connect to the network or every few times displays a message “Authentication error occurred”.
I have tried I would say every possibility that I’ve seen over the internet. That includes:
1.) Installing WiFi Connection Manager (it provided some info regarding the network that I wish to connect to: IEEE 802.11g standard, 54 Mb link and CH:11). I’ve used its function to fix the WIFI (advanced fix (root required)) but it didn’t help.
2.) All sorts of staying close to the rooter, while enabling and disabling the Power save mode (accessed via *#0011# command) or while having GSM signal.
3.) Browsing through system, data etc. folders to try to find the file that contains the MAC address information (like it did on older android versions in the nvram file). I’ve been unable to find this file or any sort of file that displays my MAC for the purpose to modify it.
I have a plan to upgrade Android to version 4.4.2 later today and make a test.
Please, feel free to suggest anything else! If I do not succeed, I will have to replace my S4 Mini with something else.
Kind regards,
QUICK REPLY: After installing CyanoGEN MOD 4.4.2, the problem remains!
I think there could be a shorter solution! On Sony Xperia Acro S with 4.1.2 Android it was just a matter of changing the MAC address within the file data/etc/wifi/fw! One minute modification...
So, please, if somebody knows the path to the file that contains MAC on CyanoGEN MOD 4.4.2 or on Android 4.2.2, PLEASE HELP!
Kind regards!