Develop Bugs

[Q] Stuck in boot loader - Please check & correct steps

Hello,
I'm stuck in bootloader (I think). It's my first attempt to flash a kernel and ROM, so I may have done something stupid... please correct any mistakes in my workflow:
1) rooted phone (ZergRush) - OK
2) Unlocked the bootloader (lollylost100) - OK
3) Flashed DoomKernelv22 using fastboot
4) Doomkernel recommends baseband36(+patch), so used flashtool to flash baseband36 (note first time I tried this I tried using "Select Kernel to Flash" - but got an error messge "FAILED (remote: Image won't fit, partition too small!)". So then I tried using "Select System to Flash", and had success:
07/005/2012 00:05:03 - INFO - Selected system (system.img or system.sin): C:\Flashtool\LT15_LT18_36_Baseband.ftf
07/005/2012 00:05:03 - INFO - Flashing selected system
07/005/2012 00:05:03 - INFO - Please check the log before rebooting into system
07/005/2012 00:05:28 - INFO - Finished Fastboot Toolbox​5)Booted into recovery and flashed the following (all in one session):
- ARC-DooMKernel-v22-modules_CWM
- PatchBaseBand36Libs.zip
- update-Arconium-8.2.zip
- update-arconium-FBInside_Timescape-v5.zip
- update-arconium-Sounds.zip
5a) didn't flash these ones:
- update-arconium-StockModules.zip (this is only for reverting back to a stock ROM?)
- couldn't find doomlord wifi/BT update, assumed it was all part of arconium? Also assumed that if this was a problem it would only affect wifi/BT not the rest of the install.
6) Booted phone - but just get a a loop of the "booting doomkernal" graphic / blank screen/buzz.
7) booted into recovery and wiped dalvik cache (no change)
8) booted into recovery and did factory reset/clear cache (no change)
9) reloaded all of the above (no change - still boot loop)
Think that's all, tried to be comprehensive.
Thanks in advance. R.

r_southampton said:
Hello,
I'm stuck in bootloader (I think). It's my first attempt to flash a kernel and ROM, so I may have done something stupid... please correct any mistakes in my workflow:
1) rooted phone (ZergRush) - OK
2) Unlocked the bootloader (lollylost100) - OK
3) Flashed DoomKernelv22 using fastboot
4) Doomkernel recommends baseband36(+patch), so used flashtool to flash baseband36 (note first time I tried this I tried using "Select Kernel to Flash" - but got an error messge "FAILED (remote: Image won't fit, partition too small!)". So then I tried using "Select System to Flash", and had success:
07/005/2012 00:05:03 - INFO - Selected system (system.img or system.sin): C:\Flashtool\LT15_LT18_36_Baseband.ftf
07/005/2012 00:05:03 - INFO - Flashing selected system
07/005/2012 00:05:03 - INFO - Please check the log before rebooting into system
07/005/2012 00:05:28 - INFO - Finished Fastboot Toolbox​5)Booted into recovery and flashed the following (all in one session):
- ARC-DooMKernel-v22-modules_CWM
- PatchBaseBand36Libs.zip
- update-Arconium-8.2.zip
- update-arconium-FBInside_Timescape-v5.zip
- update-arconium-Sounds.zip
5a) didn't flash these ones:
- update-arconium-StockModules.zip (this is only for reverting back to a stock ROM?)
- couldn't find doomlord wifi/BT update, assumed it was all part of arconium? Also assumed that if this was a problem it would only affect wifi/BT not the rest of the install.
6) Booted phone - but just get a a loop of the "booting doomkernal" graphic / blank screen/buzz.
7) booted into recovery and wiped dalvik cache (no change)
8) booted into recovery and did factory reset/clear cache (no change)
9) reloaded all of the above (no change - still boot loop)
Think that's all, tried to be comprehensive.
Thanks in advance. R.
Click to expand...
Click to collapse
i think you should
make a factory reset,wipe dalvic cache,wipe cache in recovery
then again flash doomlord kernal
and then flash acronium8.2 in recovery
and then reboot your phone
after it reboots successfully
see your phone is working
if it is working then you should enter into recovery and then flash any other zip module u want to flash
it is recommended not flash the any other zip file at the same instance when you are flashing a custom rom in recovery

Thank you abhisheak.bansal
Just did Factory Reset / Wipe Cache
Then booted to Recovery and flashed doomkernel modules
Powered off
rebooted to recovery and flashed arconium8.2
Powered off / repowered
Still loops in boot.
Need to go out now, but will try repeat slowly one step at a time from the initial kernel image using fastboot. Will leave the baseband stuff until the end in case that's confused things.

i would reccommend if all doesnt work out at all
then flash the official ftf via flashtool

1. Flash an official stock 4.0.2.A.0.42/.58/.62 FW --> http://forum.xda-developers.com/showthread.php?p=22105604
2. Flash/install the baseband patch AND the baseband itself --> http://forum.xda-developers.com/showthread.php?t=1382657
3. Flash Doomkernel --> http://forum.xda-developers.com/showthread.php?t=1172885
4. Flash the Doomkernel modules (MODULES for DooMKernel (v22)) --> http://forum.xda-developers.com/showthread.php?t=1172885
5. Flash the Arconium ROM --> http://forum.xda-developers.com/showthread.php?t=1325640 (doesn't include doomkernel 22 modules, hence step 4)
6. Flash optional Arconium packs
Apply a reboot between all steps and read/apply instructions as written the listed threads.

Thank you to all who have offered advice.
Decided to go with ICS (Arconium 3.C) and Stock Kernel+CWM. & baseband70
Flashed the above and all started working.
Although I was still on baseband-56....
That was my problem, I hadn't been using Flashtool properly. Although it appeared to be flashing something... It was until I started trying to use it in "Flashmode" rather than "Fastboot" mode (and with the firmwares in the firmware directory - rather than browsing to them), that I then got prompted to install lots of drivers... and was then able to flash the baseband properly. For those of you still reading, the 4 INFO lines in the first post do not indicate a successful baseband flash. This was the successful log:
07/039/2012 18:39:21 - INFO - Selected LT15_LT18_70_Baseband.ftf
07/039/2012 18:39:21 - INFO - Preparing files for flashing
07/039/2012 18:39:21 - INFO - Please connect your device into flashmode.
07/039/2012 18:39:27 - INFO - Device connected in flash mode
07/039/2012 18:39:27 - INFO - Opening device for R/W
07/039/2012 18:39:27 - INFO - Reading device information
07/039/2012 18:39:27 - INFO - Phone ready for flashmode operations.
07/039/2012 18:39:27 - INFO - Start Flashing
07/039/2012 18:39:27 - INFO - Flashing loader
07/039/2012 18:39:30 - INFO - Loader : S1_Loader_Root_773f - Version : R4A066 / Bootloader status : ROOTED
07/039/2012 18:39:30 - INFO - Flashing fota0.sin
07/039/2012 18:39:31 - INFO - Flashing fota1.sin
07/039/2012 18:39:32 - INFO - Flashing adsp.sin
07/039/2012 18:39:35 - INFO - Flashing amss.sin
07/039/2012 18:39:44 - INFO - Flashing amss_fs_ayame.sin
07/039/2012 18:39:45 - INFO - Ending flash session
07/039/2012 18:39:45 - INFO - Flashing finished.
07/039/2012 18:39:45 - INFO - Please wait. Phone will reboot

I was wondering why you'd want to flash a GB rom instead of an ICS one
But glad you got it sorted out!
By the way, the steps I mentioned before (minus step 2) also work for the Arconium 3C release. And if you flash the official .431 FW in step 1, you'll have baseband .72

I was thinking that GB would probably be better on single core Arc... but it was a close call.
Anyway, so far ICS is doing nicely. Certainly faster than it used to be, but that's probably down to the increase in memory I got by going with a custom ROM.
Out of curiosity, what might BB 72 offer by way of improvement?

As far as I know, there's no difference between .70 and .72 basebands.
But I found it easyer, when I did the steps, to just flash the newest firmware, which included the .72

Brick recovery

Hello all, I am requesting help with my Xperia Play.
It was not working smoothly, so I decided to install a custom ROM. I installed the ICS beta and then attempted to install xDark ICS but it has failed.
Pretty sure its R800i, bought unlocked in the UK
I cannot see anything on screen when I turn the device on
When the power button is pressed it vibrates slightly
I can put it in recovery mode (Holding Back and plugging USB) -light appears green
I can put it in fastboot mode (Holding Search and plugging USB) -light appears blue
When I try to flash any .ftf files with Flashtool it either comes up with an error or stays on "retrieving device information"
I cannot work out how to repair with PC Companion
When I select the .ftf file, no files appear in the firmware content. (I have tried various firmware files but any more would be appreciated)
My flash tool logs: When selecting firmware or dragging firmware
22/001/2012 22:01:27 - INFO - <- This level is successfully initialized
22/001/2012 22:01:27 - INFO - Flashtool Version 0.9.0.0 built on 2012-07-19 22:57:15
22/001/2012 22:01:27 - INFO - You can drag and drop ftf files here to start flashing them
22/001/2012 22:01:33 - INFO - Device connected in flash mode
22/001/2012 22:01:33 - INFO - Selected R800i_4.0.2.A.0.42_Generic_UK.ftf
22/001/2012 22:01:33 - INFO - Flash canceled
Click to expand...
Click to collapse
22/004/2012 22:04:45 - INFO - Selected R800i_4.0.2.A.0.42_Generic_UK.ftf
22/004/2012 22:04:45 - INFO - Preparing files for flashing
22/004/2012 22:04:45 - INFO - Please connect your device into flashmode.
22/004/2012 22:04:45 - INFO - Opening device for R/W
22/004/2012 22:04:45 - INFO - Reading device information
22/005/2012 22:05:01 - INFO - Start Flashing
22/005/2012 22:05:01 - INFO - Flashing loader
22/005/2012 22:05:01 - INFO - Ending flash session
22/005/2012 22:05:01 - ERROR -
22/005/2012 22:05:01 - ERROR - Error flashing. Aborted
22/005/2012 22:05:01 - INFO - Device disconnected
Click to expand...
Click to collapse
This sometimes appears
22/010/2012 22:10:03 - INFO - Selected R800i_4.0.2.A.0.42_Generic_UK.ftf
22/010/2012 22:10:03 - INFO - Preparing files for flashing
22/010/2012 22:10:03 - INFO - Please connect your device into flashmode.
22/010/2012 22:10:04 - INFO - Opening device for R/W
22/010/2012 22:10:04 - INFO - Reading device information
22/010/2012 22:10:04 - INFO - Phone ready for flashmode operations.
22/010/2012 22:10:04 - INFO - Start Flashing
22/010/2012 22:10:04 - INFO - Flashing loader
22/010/2012 22:10:04 - INFO - Ending flash session
22/010/2012 22:10:04 - ERROR - ERR_SEVERITY="MAJOR";ERR_CLASS="SECURITY_CLASS";ERR_DYNAMIC="SIN header verification failed"
Click to expand...
Click to collapse
I'm not interested in what I did wrong I just want my phone functionality back.
I want the stock rom back on my phone. Thanks!

Do you know how to flash roms with flash tools?
Sure that your phon has unlock bootloader? (if don't, follow this http://unlockbootloader.sonymobile.com/instructions)
The same problem happened to me... I learn how to unlock bootloader and install roms with flashtools... now I'm running CM9 RC2...
If you know how to flsh see post #5 of this thread...http://forum.xda-developers.com/showthread.php?p=28977879#post28977879
if you don´t, Tell me!
cheers :good:

Alejandroch said:
Do you know how to flash roms with flash tools?
Sure that your phon has unlock bootloader? (if don't, follow this http://unlockbootloader.sonymobile.com/instructions)
The same problem happened to me... I learn how to unlock bootloader and install roms with flashtools... now I'm running CM9 RC2...
If you know how to flsh see post #5 of this thread...http://forum.xda-developers.com/showthread.php?p=28977879#post28977879
if you don´t, Tell me!
cheers :good:
Click to expand...
Click to collapse
Yeah I know how but I cant access the recovery menu.
Anyway, I resolved the issue by flashing the latest stock (.62) .ftf file from here and it seemed to work. Thanks

[Q] something gone wrong when flashing

So here's what I did so far... The bootloader was unlocked, so I rooted the phone, installed clockwork. I spent hours reading about kernels and the different roms but wasn' really getting anywhere. Since my phone needed to be taken to get repaired anyway I decided to just choose a rom and install it from the guide i was using.
I backed up using clockwork, formatted and installed, and it said it was fine. But when I reboot it just hangs on the Sony Ericsson screen, have to take battery out to turn it off....what can I do now? I can't load the backup image because it won't let me load clockwork. did this happen because I didn't install a custom kernel first?

renvaar said:
So here's what I did so far... The bootloader was unlocked, so I rooted the phone, installed clockwork. I spent hours reading about kernels and the different roms but wasn' really getting anywhere. Since my phone needed to be taken to get repaired anyway I decided to just choose a rom and install it from the guide i was using.
I backed up using clockwork, formatted and installed, and it said it was fine. But when I reboot it just hangs on the Sony Ericsson screen, have to take battery out to turn it off....what can I do now? I can't load the backup image because it won't let me load clockwork. did this happen because I didn't install a custom kernel first?
Click to expand...
Click to collapse
flash another kernel (supported for your rom always)
boot on cwm
factory reset
mounts and storage > format system
advanced > wipe dalvik cache
advanced > wipe battery stats
flash your desirable rom, flash wifi modules and try again fresh

renvaar said:
So here's what I did so far... The bootloader was unlocked, so I rooted the phone, installed clockwork. I spent hours reading about kernels and the different roms but wasn' really getting anywhere. Since my phone needed to be taken to get repaired anyway I decided to just choose a rom and install it from the guide i was using.
I backed up using clockwork, formatted and installed, and it said it was fine. But when I reboot it just hangs on the Sony Ericsson screen, have to take battery out to turn it off....what can I do now? I can't load the backup image because it won't let me load clockwork. did this happen because I didn't install a custom kernel first?
Click to expand...
Click to collapse
Your kernel is stock and bootloader locked? If so then download pc companion and do a repair and if your bootloader is unlocked then download a stock ftf file for your phone and flash it with flashtool. I had exactly same problem with flashing custom firmwares on my Arc s but after few tries I realized that i need to format every partition excluding sdcard in a "mounts and storage" sub-menu.
---------- Post added at 11:31 AM ---------- Previous post was at 11:29 AM ----------
Retrosid said:
flash another kernel (supported for your rom always)
boot on cwm
factory reset
mounts and storage > format system
advanced > wipe dalvik cache
advanced > wipe battery stats
flash your desirable rom, flash wifi modules and try again fresh
Click to expand...
Click to collapse
I think his bootloader is locked because he lost a recovery after flashing new rom. His CWM was probably installed with x-parts.

as I said... it wont let me go as far as being able to load up clockwork...
thanks pypcier, I'm trying flashtool now... but I get this error...
18/036/2013 18:36:40 - INFO - Device disconnected
18/036/2013 18:36:53 - INFO - Device connected in flash mode
18/037/2013 18:37:03 - INFO - Selected LT15i_4.0.2.A.0.42_Generic Global.ftf
18/037/2013 18:37:03 - INFO - Preparing files for flashing
18/037/2013 18:37:03 - INFO - Please connect your device into flashmode.
18/037/2013 18:37:03 - INFO - Opening device for R/W
18/037/2013 18:37:03 - INFO - Reading device information
18/037/2013 18:37:03 - INFO - Phone ready for flashmode operations.
18/037/2013 18:37:03 - INFO - Current device : LT15i - CB5A1FEFCM - 1247-1061_R7D - 1241-4324_4.0.2.A.0.42 - WORLD-1-8_4.0.2.A.0.42
18/037/2013 18:37:03 - INFO - Start Flashing
18/037/2013 18:37:03 - INFO - Processing loader
18/037/2013 18:37:03 - INFO - Checking header
18/037/2013 18:37:03 - INFO - Ending flash session
18/037/2013 18:37:03 - ERROR - ERR_SEVERITY="MAJOR";ERR_CLASS="SECURITY_CLASS";ERR_DYNAMIC="SIN header verification failed"

Can you tick a "no final verification" box and try again?

it changes to this if i check the button...
18/052/2013 18:52:28 - INFO - Selected LT15i_4.0.2.A.0.42_Generic Global.ftf
18/052/2013 18:52:28 - INFO - Preparing files for flashing
18/052/2013 18:52:28 - INFO - Please connect your device into flashmode.
18/052/2013 18:52:29 - INFO - Opening device for R/W
18/052/2013 18:52:29 - INFO - Reading device information
18/052/2013 18:52:45 - INFO - Unable to read from phone after having opened it.
18/052/2013 18:52:45 - INFO - trying to continue anyway
18/052/2013 18:52:45 - INFO - Start Flashing
18/052/2013 18:52:45 - INFO - Processing loader
18/052/2013 18:52:45 - INFO - Checking header
18/052/2013 18:52:45 - INFO - Ending flash session
18/052/2013 18:52:45 - ERROR - Error in processHeader : 2 : The system cannot find the file specified.
18/052/2013 18:52:45 - ERROR - Error flashing. Aborted
18/052/2013 18:52:45 - INFO - Device disconnected
EDIT: it did that the first time, then i try the same way again and it gives me the previous error. would an older ftf make a difference?

You are sure that your bootloader is unlocked? Have you ever flashed a custom kernel using fastboot? If yes then try to flash custom kernel with recovery. If this wont help then try to update and reinstall your flashtool and download newest stock ftf for your phone.

I'm pretty sure it is, as I remember having a similar problem a long time ago and flashing it. problem is I don't have the old files i used before, and I can't find any downloads that work in my country..

Error code from your flashtool log looks like there is a problem with acquiring permission to flash a firmware and that suggests that your bootloader is locked. Try to download pc companion from sony site and do a repair. If your bootloader is locked this will restore your phone to stock and if your bootloader is unlocked then pcc wont recognize your phone.

just tried pc companion. it asks me to swipe the bar down, but as I can't get past the logo it wont work. so repair just hangs there...

What bar... I don't understand what you are talking about. For a repair with pc companion you don't even need to turn on your phone you just click update button and then small blue "repair" text in a popup window then firmware is downloaded and you are asked to turn off your phone and connect usb cable while holding a back button.
I found your previous thread and It looks like your bootloader is unlocked because OTA update bricked your phone. I have a link to a ftf you used last time to repair your phone http://forum.xda-developers.com/showthread.php?t=1324707 (its inside of this archive with complete but outdated flashtool and drivers) but you should try a pcc first so we will be sure if your bootloader is locked or not.

renvaar said:
just tried pc companion. it asks me to swipe the bar down, but as I can't get past the logo it wont work. so repair just hangs there...
Click to expand...
Click to collapse
Use this http://developer.sonymobile.com/201...ocked-xperia-smartphones-video-beta-download/ if your bootloader is unlocked it will return it to stock if it does not connect it means your bootloader is locked.It is a new beta tool from sony for the arc:good:

tallman43 said:
Use this http://developer.sonymobile.com/201...ocked-xperia-smartphones-video-beta-download/ if your bootloader is unlocked it will return it to stock if it does not connect it means your bootloader is locked.It is a new beta tool from sony for the arc:good:
Click to expand...
Click to collapse
Wow its great I hadn't heard of this before.

pypcier said:
Wow its great I didn't heard of this before.
Click to expand...
Click to collapse
Yep it's a good tool to return to stock and also to check if your bootloader is unlocked (Because it only works on unlocked bootloaders) Arc & couple other devices are supported but they are going to make more devices available:good:

pypcier said:
Wow its great I hadn't heard of this before.
Click to expand...
Click to collapse
You would have had you browsed the stickys.

XperienceD said:
You would have had you browsed the stickys.
Click to expand...
Click to collapse
I'm not going to read through every new sticky just to make you happy.

pypcier said:
I'm not going to read through every new sticky just to make you happy.
Click to expand...
Click to collapse
Mines been there while, and People shouldn't read them to please anyone, they should read them, especially when new, to LEARN.
Sent from Myushi

[Help] I think I bricked my phone ?

Hey guys. I wanted to install CM 10 the Free Xperia one but it's stuck on the boot img. I flashed the kernel and when I try to install from recovery the zip it gives me an error. I wanted to connect my usb to copy the file again maybe it didn't copy right but I cant mount usb I get an error again. I tried to plug the usb when it's at boot and with Flashtool to flash the stock ftf the 58. And it gives me this.
21/016/2013 19:16:56 - INFO - <- This level is successfully initialized
21/016/2013 19:16:56 - INFO - Flashtool Version 0.9.10.1 built on 2013-01-09 19:49:47
21/016/2013 19:16:56 - INFO - You can drag and drop ftf files here to start flashing them
21/016/2013 19:16:58 - INFO - Device disconnected
21/017/2013 19:17:03 - INFO - Selected R800i_4.0.2.A.0.58_Enhanced.ftf
21/017/2013 19:17:03 - INFO - Preparing files for flashing
21/017/2013 19:17:04 - ERROR -

nakuk21
First turn off your phone and try with fastboot if it works !!

I mannaged to install doom kernel and nxt so I booted in. But still I have the same thing when I want to flash the stock tft ERROR-

The ftf file may be corrupted. Check if the md5 sum matches and/or download it again

[FIX] Restoring Flashmode

UPD: same fix for Xperia L (C2105)
Some phones (I mean only Xperia M of course) for unknown reason can't enter to Flashmode (Vol Down + USB)
This mode obliviously required to flash stock ROM via Flashtool / PC Companion / SEUS
When try to enter it phone just won't connect. But phone itself works fine (can boot).
Yeah, there is stock CWM-backups, but anyway broken mode is not good.
I did some research with user that had this problem and found cause.
Somehow 4th partition (s1sbl2) contain wrong data – it mismatch with OK phone.
Seems there stored loader for dealing with flashing.
After restoring good partition dump Flashmode works!
This helped 2 people, so I want to share this widely.
Do it on your own risk.
If you have custom recovery (CWM / TWRP)
1. Download attached ZIP
2. Copy it somewhere on phone
3. Flash it via recovery like any other ZIP
If you have only root
0. Not rooted? Use Towelroot for 4.3
1. Download attached file 1.img
2. Copy it into root of internal storage
3. Install app Terminal Emulator
4. Launch it and enter su
5. Allow root access
6. Carefully enter this (at the end not number 12, there small L and 2):
Code:
dd if=/sdcard/1.img of=/dev/block/platform/msm_sdcc.1/by-name/s1sbl2

i have this promblem where the green only blink once how can i fix it cause im already stucked at sony logo

nikko3214123 said:
how can i fix it cause im already stucked at sony logo
Click to expand...
Click to collapse
1. Copy that ZIP with fix to sdcard via cardreader
2. Unlock bootloader (required only fastboot, Google for tutorial)
3. Install via fastboot kernel with CWM (link in post)
4. Enter CWM: at Sony logo & purple LED press Vol Up (or Down?)
5. Flash that ZIP
6. Now flash stock ROM via Flashtool
Note: all your data on phone including internal storage will be erased (twice)
Please, write here about result.

Bonoboo said:
1. Copy that ZIP with fix to sdcard via cardreader
2. Unlock bootloader (required only fastboot, Google for tutorial)
3. Install via fastboot kernel with CWM (link in post)
4. Enter CWM: at Sony logo & purple LED press Vol Up (or Down?)
5. Flash that ZIP
6. Now flash stock ROM via Flashtool
Note: all your data on phone including internal storage will be erased (twice)
Please, write here about result.
Click to expand...
Click to collapse
sir i dont have cwm on the phone is there any way to fix this? thanks for the quick response

nikko3214 said:
i dont have cwm on the phone is there any way to fix this?
Click to expand...
Click to collapse
No.
You need install CWM via fastboot after unlocking bootloader.
I already described this.

Bonoboo said:
No.
You need install CWM via fastboot after unlocking bootloader.
I already described this.
Click to expand...
Click to collapse
im stucked at < waiting for device > my phone is already on fastboot mode
---------- Post added at 10:18 AM ---------- Previous post was at 10:04 AM ----------
and im having trouble with flashtool it says
13/016/2015 18:16:29 - INFO - Current device : C1905 - YT910HYWCB - 1274-5438_R3A - 1272-2325_15.1.C.1.17 - WORLD-i_15.1.C.1.17
13/016/2015 18:16:29 - INFO - Start Flashing
13/016/2015 18:16:29 - INFO - Processing loader.sin
13/016/2015 18:16:29 - INFO - Checking header
13/016/2015 18:16:29 - INFO - Flashing data
13/016/2015 18:16:29 - INFO - Processing of loader.sin finished.
13/016/2015 18:16:29 - INFO - Loader : S1_Root_dbe9 - Version : loader_MSM8X30_10 / Boot version : S1_Boot_MSM_8227_5 / Bootloader status : ROOTABLE
13/016/2015 18:16:30 - INFO - Processing partition-image.sin
13/016/2015 18:16:30 - INFO - Checking header
13/016/2015 18:16:30 - INFO - Flashing data
13/016/2015 18:16:30 - INFO - Processing of partition-image.sin finished.
13/016/2015 18:16:30 - INFO - No bootdelivery to send
13/016/2015 18:16:30 - INFO - Processing kernel.sin
13/016/2015 18:16:30 - INFO - Checking header
13/016/2015 18:16:30 - INFO - Flashing data
13/016/2015 18:16:30 - ERROR - Processing of kernel.sin finished with errors.
13/016/2015 18:16:30 - INFO - Ending flash session
13/016/2015 18:16:30 - ERROR -
13/016/2015 18:16:30 - ERROR - Error flashing. Aborted
13/016/2015 18:16:30 - INFO - Device connected in flash mode
13/016/2015 18:16:31 - INFO - Device disconnected

nikko3214 said:
Device connected in flash mode
Click to expand...
Click to collapse
So you don't need this fix if Flashtool recognize phone.
What actually happen with phone?
Suddenly rebooted and stuck and animation?
Log probably point to often problem with NAND chip - it just going broken, similar to HDD / SSD.

Bonoboo said:
So you don't need this fix if Flashtool recognize phone.
What actually happen with phone?
Suddenly rebooted and stuck and animation?
Log probably point to often problem with NAND chip - it just going broken, similar to HDD / SSD.
Click to expand...
Click to collapse
this phone suddenly reboots and then it got stucked to sony logo and when i put it on flashmode the green only blinks once then when i am flashing sometimes the loader.sin has error or the kerne.sin

nikko3214 said:
suddenly reboots and then it got stucked to sony logo ... sometimes the loader.sin has error or the kernel.sin
Click to expand...
Click to collapse
Unfortunately, very likely this is classic faulty NAND memory problem.
There's a lot people faced this on XDA and other forums.
Only replacing board, probably by warranty.

Bonoboo said:
Unfortunately, very likely this is classic faulty NAND memory problem.
There's a lot people faced this on XDA and other forums.
Only replacing board, probably by warranty.
Click to expand...
Click to collapse
ok thank you for helping sir

Plz Help
i have xperia m, after unlocking bootloader it stuck on bootlooping, i have not enable usb debugging...any way to fix it?

catmob said:
i have xperia m, after unlocking bootloader it stuck on bootlooping
Click to expand...
Click to collapse
It's normal, just flash stock via Flashtool
Or you can't due broken flashmode?

Bonoboo said:
It's normal, just flash stock via Flashtool
Or you can't due broken flashmode?
Click to expand...
Click to collapse
when i am going to flash...for disabling usb debugging previously, i cant flash my phone...please help me

catmob said:
when i am going to flash i cant flash my phone
Click to expand...
Click to collapse
Please, explain problem in details.
At what step you actually stuck?

Bonoboo said:
Please, explain problem in details.
At what step you actually stuck?
Click to expand...
Click to collapse
sir i have going to unlock my bootloader without enable usb debugging & also i have not installed any custom recovery mode.
now my phone stuck into bootloop...
now what will i do? i can go to fastboot mode and flashmode,
and i have read some instruction about flashing via flashtool...when i am going to flash my phone..it showing error that i have to enable usb debuging to flash the rom
sir plz help me

catmob said:
when i am going to flash my phone..it showing error that i have to enable usb debuging to flash the rom
Click to expand...
Click to collapse
You definitely just need flash stock via Flashtool.
Forget about USB debugging, it's totally unrelated here.
Just carefully follow flashing tutorial
You need flash not in fastboot mode, but in flashmode.

Bonoboo said:
You definitely just need flash stock via Flashtool.
Forget about USB debugging, it's totally unrelated here.
Just carefully follow flashing tutorial
You need flash not in fastboot mode, but in flashmode.
Click to expand...
Click to collapse
ok will my problem solved sir? following these steps?

catmob said:
ok will my problem solved sir? following these steps?
Click to expand...
Click to collapse
Again: yes.

Bonoboo said:
Again: yes.
Click to expand...
Click to collapse
Thnk you so much sir....you saved my life....my prblm has been solved

sir can i flash another rom (not official) like mi,cyaongen mod without root?