Develop Bugs

Diag mode

I need to enter in diag mode to use CDMATools. I didn't find any metod for this phone. Can you help me?

When your phone is power on it is already in diag mode I think, but I am not expert

Water damaged OP3 only shows Tux at boot for 3 seconds (hard brick?)

Hello,
I've got a water damaged OP3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a Linux Logo (a small Tux in the middle of the screen) and then turns off after 3 seconds. If I connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could I try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
best regards and thanks in advance!

Contact a software technician
juuz said:
hello,
i've got a water damaged op3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a linux logo (a small tux in the middle of the screen) and then turns off after 3 seconds. If i connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could i try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
Best regards and thanks in advance!
Click to expand...
Click to collapse
you better avoid doing experiments on op3. Symptoms you have mentioned in your thread, tells that your has been flashed (don't have usb drivers,no os,no firmware). I have faced same problem with my letv le 1s. It is a software problem. Your phone is totally empty. So do contact with any software technician, he uses sp flash tool to wake up the device. Download sp flash tool and follow procedure. If sp flash tool is detecting your device then it means your device hardware is fine.

juuz said:
Hello,
I've got a water damaged OP3 (it was in a pool for about 1min). Now after a few days having it in a pot of rice and cleaning the logic board with 100% isopropanol it finally woke up when pressing power button.
My problem now: It just shows up with a Linux Logo (a small Tux in the middle of the screen) and then turns off after 3 seconds. If I connect it with a charger, the screen persists for the moment.
When pressing + holding volume up button, windows recognizes it as "unknown usb device" and screen stays black.
I only need to access the flash to rescue some of my recent (of course not backed up) data.
What do you suggest? Could I try the unbrick the phone or do these symptons point to a irreversible hardware damage?
Is there a way to read the flash without flashing (or with flashing a minimum set of) stock image?
best regards and thanks in advance!
Click to expand...
Click to collapse
Have you installed the necessary drivers in Windows for the phone to show up as Qualcom HS-USB..........Loader9008? Otherwise your phone will not be recognised when you do volume press for 10 seconds and connect. Even if it is recognised in this "service" mode, you may be able to unbrick/restore your phone but in the process, the entire phone would be wiped clean. (I know since I have done it).

tnsmani said:
Have you installed the necessary drivers in Windows for the phone to show up as Qualcom HS-USB..........Loader9008? Otherwise your phone will not be recognised when you do volume press for 10 seconds and connect. Even if it is recognised in this "service" mode, you may be able to unbrick/restore your phone but in the process, the entire phone would be wiped clean. (I know since I have done it).
Click to expand...
Click to collapse
I've tried to get the phone into EDL Mode (Qualcomm chip), but had no success, phone vibrates and windows recognizes an "unknown usb device" (pressed Volume Up and connected to USB, phone was definitely turned off). But I am not able to get the device recognized as "QHSUSB_BULK" which - afaik - is the prerequisite to install the Qualcomm USB Driver und go on with the unbrick procedure..
I hope anyone got some idea how to get the phone back to life..

juuz said:
I've tried to get the phone into EDL Mode (Qualcomm chip), but had no success, phone vibrates and windows recognizes an "unknown usb device" (pressed Volume Up and connected to USB, phone was definitely turned off). But I am not able to get the device recognized as "QHSUSB_BULK" which - afaik - is the prerequisite to install the Qualcomm USB Driver und go on with the unbrick procedure..
I hope anyone got some idea how to get the phone back to life..
Click to expand...
Click to collapse
Your understanding of the unbrick steps is not correct. Initially the phone will not show up at all or may show up as unknown or something else. It is only when you install the EDL mode drivers and then hold the power button down for 40 seconds and the hold down the volume up button for 10 seconds and connect to PC, will it show up in the EDL mode. Ofcourse you will have to disable the driver signature verification before installing the drivers.
Read the Unbrick Guide again and install the drivers before trying to connect.

tnsmani said:
Your understanding of the unbrick steps is not correct. Initially the phone will not show up at all or may show up as unknown or something else. It is only when you install the EDL mode drivers and then hold the power button down for 40 seconds and the hold down the volume up button for 10 seconds and connect to PC, will it show up in the EDL mode. Ofcourse you will have to disable the driver signature verification before installing the drivers.
Read the Unbrick Guide again and install the drivers before trying to connect.
Click to expand...
Click to collapse
Thanks so far, but being a software developer myself I am not a totally beginner. I followed the guide, also read it twice etc.. Also tried another USB cable including the original Oneplus cable.
When plugging it in while pressing Volume Up my Linux laptop reports this:
Code:
[40474.458362] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426231] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426354] usb usb3-port2: attempt power cycle
[40476.710061] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.677934] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.678051] usb usb3-port2: unable to enumerate USB device
On my windows machine the device manager reports "Windows has stopped the device because it has reported problems. (Code 43)".
Any suggestions? It seems that the device has lost all firmware etc. and there is no EDL left on the device.
EDIT:
With holding Vol(-) and Power I could get rid of the Tux Penguin and enter fastboot and recovery of the phone.. NAND seems to be okay, can decrypt my internal storage.. The USB port doesn't work in recovery (same error like I had with the EDL mode, unknown device)..
I hope I can now charge the battery a bit and recovery my data...
Thanks so far guys..

juuz said:
Thanks so far, but being a software developer myself I am not a totally beginner. I followed the guide, also read it twice etc.. Also tried another USB cable including the original Oneplus cable.
When plugging it in while pressing Volume Up my Linux laptop reports this:
Code:
[40474.458362] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426231] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40475.426354] usb usb3-port2: attempt power cycle
[40476.710061] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.677934] usb usb3-port2: Cannot enable. Maybe the USB cable is bad?
[40477.678051] usb usb3-port2: unable to enumerate USB device
On my windows machine the device manager reports "Windows has stopped the device because it has reported problems. (Code 43)".
Any suggestions? It seems that the device has lost all firmware etc. and there is no EDL left on the device.
EDIT:
With holding Vol(-) and Power I could get rid of the Tux Penguin and enter fastboot and recovery of the phone.. NAND seems to be okay, can decrypt my internal storage.. The USB port doesn't work in recovery (same error like I had with the EDL mode, unknown device)..
I hope I can now charge the battery a bit and recovery my data...
Thanks so far guys..
Click to expand...
Click to collapse
Sorry if I had sounded condescending, but I had no way of knowing your level of expertise.
Best of luck for restoring your phone or for saving the data.

tnsmani said:
Sorry if I had sounded condescending, but I had no way of knowing your level of expertise.
Best of luck for restoring your phone or for saving the data.
Click to expand...
Click to collapse
No need to worry.. Of course, you couldn't know and there are a lot of people asking dump questions..
My phone is back a life, I guess the data transfer via USB is not working anymore, charging works although I needed to take my Oneplus One's battery (identical connector, just need to take care of the pin layout [+/-]) because my OP3 battery is pretty low and I don't know if I can reactivate it.. It has about 3,4V at the moment and charges very slow..
Finally, if anyone else faces this issue and can't boot his phone:
Try different button combinations and keep holding the buttons several seconds/minutes..

LG G8 STUCK IN Qualcomm HS-USM QDLoader 9008

Today I Bricked My LG820Qm
I was updating my Lg g8 using LG UP, When the Process on 64% my PC power off
After that my phone stuck in Qualcomm HS-USM QDLoader 9008
Any solution to come out from this mode to Downloaded Mode so that i can update using LG up.
I was updating G820QM10i_00_NAO_US_OP_0401 to G820QM20b_00_NAO_US_OP_1224
My LG up LGUP_Lab_Frame_Ver_1_16_0_3

Can you try to switch to download mode by press&hold VOL+ while inserting the USB cable (connected to PC). Phone needs to be off while doing so.

tron1 said:
Can you try to switch to download mode by press&hold VOL+ while inserting the USB cable (connected to PC). Phone needs to be off while doing so.
Click to expand...
Click to collapse
I tried not working
If i press&hold VOL+ while inserting the USB cable still my phone come with Qualcomm HS-USB Mode
thanks for your reply

What happens if you press&hold VOL- (furing the whole procedure) push the power button until the phone vibrates, release the button und press&hold the power button?

tron1 said:
What happens if you press&hold VOL- (furing the whole procedure) push the power button until the phone vibrates, release the button und press&hold the power button?
Click to expand...
Click to collapse
Which ever combination, Vol- + power phone power of
with in sec it boot to Qualcomm mode

I don't know where to ask so I'm gonna try here. My G820N is stuck on Android 10 beta. Whenever I flash an official kdz, it only allows for emergency calls. Can't do anything. Any help would be appreciated

Following, in right here with ya.

atsuisofu said:
Following, in right here with ya.
Click to expand...
Click to collapse
Try entering download mode with phone disconnected from USB cable.
Also try to see if it gets recognized by LG-UP or by LG Bridge. These 2 softwares don't need download mode to be able to flash, just the phone to be recognized on some PORT.
Try also factory reset hard menu. Also try switching between Slot A and Slot B. There is also this backup method. Phone is not dead on one of those slots.
If nothing works (but slot a slot b should 100% work) , wait for the firehose, it's just around the corner. That will restore the phone back 100%.
For more info search v50thinq on telegram app. :good:

I can t get to download as it freezes and without the USB cable it doesn't even try and enter. I appreciate the recommendations. I was thinking of the a/b seit hbut without the use of fastboot I am at a loss of how to switch between the two as I thought the system chose and the switch happened upon rebooting once a system had been selected ie as in turning the unit off after loading the os set a flag to go to the opposite system upon completing the inftframs and boot sequence.

vikramanananda said:
Which ever combination, Vol- + power phone power of
with in sec it boot to Qualcomm mode
Click to expand...
Click to collapse
Hi, i'm facing the same problem today, my QM will not go into any mode other than the Qualcomm mode. Were you able to recover your phone finally ?

vikramanananda said:
Which ever combination, Vol- + power phone power of
with in sec it boot to Qualcomm mode
Click to expand...
Click to collapse
did you ever get it fixed. im having the same problem.

johnnycm77 said:
did you ever get it fixed. im having the same problem.
Click to expand...
Click to collapse
me too, do you fix it?

vikramanananda said:
Today I Bricked My LG820Qm
I was updating my Lg g8 using LG UP, When the Process on 64% my PC power off
After that my phone stuck in Qualcomm HS-USM QDLoader 9008
Any solution to come out from this mode to Downloaded Mode so that i can update using LG up.
I was updating G820QM10i_00_NAO_US_OP_0401 to G820QM20b_00_NAO_US_OP_1224
My LG up LGUP_Lab_Frame_Ver_1_16_0_3
Click to expand...
Click to collapse
So, if the device, as you say, lost power during an update like that, then almost assuredly you have at least one, if not numerous corrupted partitions.
And, it's specific partitions on the device that allow it to enter download mode. One of these most know about or have heard of is the laf partition. But other have to be there also for it to work, I don't remember exactly what the others off the top of my head, but that info is easily found.
The key thing you need (or any others commenting same prob), is to be able to enter EDL mode and have qfil installed and recognizing the device. If you can get that far, it would be easy to find the correct partitions you could flash with qfil and then immediately go from qfil to download mode.
Many many people have done this. Just get qfil set up (see guides section) and get the device recognized. that takes some effort but it's def doable.

Sp flash tools advanced mode

I'm only using all caps in hopes that more people will see what i write while in sp flash tools if you hold down ctrl alt plus v it will enter into an advanced mode which gives you considerably more flashing options plus recognition options for the device and computer i've never seen anyone mention this advanced mode before it baffles me using this method of advanced mode is what got my phone to flash without an authorized account i hope this helps other people thank you

Sherfield41 said:
I'm only using all caps in hopes that more people will see what i write while in sp flash tools if you hold down ctrl alt plus v it will enter into an advanced mode which gives you considerably more flashing options plus recognition options for the device and computer i've never seen anyone mention this advanced mode before it baffles me using this method of advanced mode is what got my phone to flash without an authorized account i hope this helps other people thank you
Click to expand...
Click to collapse
What version of my flash?

Geison Bourne said:
What version of my flash?
Click to expand...
Click to collapse
I used file "SP_Flash_Tool-5.1924_Win.zip"
And once I ran the file using administrator privileges I press Ctrl alt + v to enter advanced mode be advised that yes my phone was hard bricked, no fastboot no recovery no vibration when holding power plus volume or minus volume I only had LED light when hooked up to computer I had to remove battery but it did flash completely without the need for activated or upgraded deep flash xiaomi account or whatever you call the account

Bro, my pc can't detect my phone without battery

Sherfield41 said:
I'm only using all caps in hopes that more people will see what i write while in sp flash tools if you hold down ctrl alt plus v it will enter into an advanced mode which gives you considerably more flashing options plus recognition options for the device and computer i've never seen anyone mention this advanced mode before it baffles me using this method of advanced mode is what got my phone to flash without an authorized account i hope this helps other people thank you
Click to expand...
Click to collapse
Ok Bro I just entered that advanced mode in MiFlash Pro / SP Flash tool but what next, can you give us some little tutorial?

adrian1234a said:
Bro, my pc can't detect my phone without battery
Click to expand...
Click to collapse
what version of windows are you using? Try not to get frustrated or offended from the questions I ask I'm just trying to figure out where you are and where your computer is as far as preparedness. What drivers did you install for detection of the phone? when you installed those drivers did you install them while your computer was booted into disable driver signature verification mode? When you have SP flash tools open also open device manager and move it to the side so you can see actions in real time. What happens when you plug in the phone while holding button combinations? Do you see any changes in the device manager? If so what com's come up? There should be at least 2 variantes each with a different port number/com possibly up to 4.
As far as what should be selected once you're in advanced mode for the SP flash tools that's impossible for me to give definite answer for every single computer due to setup variance, hardware implications, and even computer brand names that treat different devices unfairly. But obviously under configuration go to connection if your battery is connected then check with battery if you have disconnected the battery then check without battery sometimes USB 3 can cause issues with flashing if you only have USB 3 then try the full speed option instead of high speed.

kamyk70 said:
Ok Bro I just entered that advanced mode in MiFlash Pro / SP Flash tool but what next, can you give us some little tutorial?
Click to expand...
Click to collapse
please be more specific with your questions and requests because I would be here all your long trying to type out every possible scenario with my own mind making the scenario so I'm happy to answer any questions but just please try to be more to the point don't be offended by that comment I'm just an a****** when it comes to trying to figure out how to say things politely.
what version of windows are you using? Try not to get frustrated or offended from the questions I ask I'm just trying to figure out where you are and where your computer is as far as preparedness. What drivers did you install for detection of the phone? when you installed those drivers did you install them while your computer was booted into disable driver signature verification mode? When you have SP flash tools open also open device manager and move it to the side so you can see actions in real time. What happens when you plug in the phone while holding button combinations? Do you see any changes in the device manager? If so what com's come up? There should be at least 2 variantes each with a different port number/com possibly up to 4.
As far as what should be selected once you're in advanced mode for the SP flash tools that's impossible for me to give definite answer for every single computer due to setup variance, hardware implications, and even computer brand names that treat different devices unfairly. But obviously under configuration go to connection if your battery is connected then check with battery if you have disconnected the battery then check without battery sometimes USB 3 can cause issues with flashing if you only have USB 3 then try the full speed option instead of high speed.

It won't work without an approved account ... absolutely ...

moto z2 on "press any key to shutdown" potential hardbrick

I was clearing the sde partitions and my phone suddenly went blank and it is not starting any more.
if I plug it to the laptop it shows charging symbol and "press any key to shutdown" message on left top corner.
It is not getting detected as qualcom or anything it is not booting to bootloader. sometimes it is showing tmobile boot image.
Phone model XT1789-04
Please help , how can blankfash and get the bootloader back? how to go to EDL mode from here ?

latadswapnil said:
I was clearing the sde partitions and my phone suddenly went blank and it is not starting any more.
if I plug it to the laptop it shows charging symbol and "press any key to shutdown" message on left top corner.
It is not getting detected as qualcom or anything it is not booting to bootloader. sometimes it is showing tmobile boot image.
Phone model XT1789-04
Please help , how can blankfash and get the bootloader back? how to go to EDL mode from here ?
Click to expand...
Click to collapse
The phone is unbrickable unless the hardware issue.
Sent from my LG-LS997 using Tapatalk

cgigate said:
The phone is unbrickable unless the hardware issue.
Sent from my LG-LS997 using Tapatalk
Click to expand...
Click to collapse
Can you please suggest a way to get into bootloader ? because currently whenever I switch on phone it shows tmobile logo(boot screen) and nothing happens and there is a message in left top corner "press any key to shutdown" . I tried to switch it on with volume down and power key but nothing happens blank screen.
Also it is not getting detected on my laptop not even as unknown device.

latadswapnil said:
Can you please suggest a way to get into bootloader ? because currently whenever I switch on phone it shows tmobile logo(boot screen) and nothing happens and there is a message in left top corner "press any key to shutdown" . I tried to switch it on with volume down and power key but nothing happens blank screen.
Also it is not getting detected on my laptop not even as unknown device.
Click to expand...
Click to collapse
Have you tried holding vol up and pwr to boot into bootloader?

41rw4lk said:
Have you tried holding vol up and pwr to boot into bootloader?
Click to expand...
Click to collapse
Yes I did try that and it only shows the Tmobile boot screen and "press any key to shutdown" on left top of screen as attached in the picture. :crying:

latadswapnil said:
Yes I did try that and it only shows the Tmobile boot screen and "press any key to shutdown" on left top of screen as attached in the picture. :crying:
Click to expand...
Click to collapse
Make sure you're using a 2.0 port from your mobo, not a hub and not a 3.0+ port.
Unplug your phone and try entering these commands one at a time, you might need to unplug before each command.
This all depends on whether you had your bootloader unlocked, adb enabled, etc. You put yourself in a weird state.
Unplug, open cmd prompt and enter
fastboot reboot bootloader it should say waiting for device
plug in your phone and hopefully it'll get you there. If not, repeat above and try
adb reboot bootloader
following the same procedure
fastboot reboot recovery
like above
adb reboot recovery
Hopefully one of those will get you somewhere where you can try to reflash the phone, factory reset, whatever it takes.
Since your pc doesn't recognize your device... who knows.
Last resort
Fastboot oem blankflash
If that works you should be ready to blankflash

41rw4lk said:
Make sure you're using a 2.0 port from your mobo, not a hub and not a 3.0+ port.
Unplug your phone and try entering these commands one at a time, you might need to unplug before each command.
This all depends on whether you had your bootloader unlocked, adb enabled, etc. You put yourself in a weird state.
Unplug, open cmd prompt and enter
fastboot reboot bootloader it should say waiting for device
plug in your phone and hopefully it'll get you there. If not, repeat above and try
adb reboot bootloader
following the same procedure
fastboot reboot recovery
like above
adb reboot recovery
Hopefully one of those will get you somewhere where you can try to reflash the phone, factory reset, whatever it takes.
Since your pc doesn't recognize your device... who knows.
Last resort
Fastboot oem blankflash
If that works you should be ready to blankflash
Click to expand...
Click to collapse
Yes bootloader was unlocked and adb was enabled also phone was rooted.
I am trying what you have suggested but its not working till now. I tried on USB 2.0 ports and 3.0 as well but nothing happens. neither blankflash executes nor any of fastboot or adb commands executes.
will linux OS help ?

latadswapnil said:
Yes bootloader was unlocked and adb was enabled also phone was rooted.
I am trying what you have suggested but its not working till now. I tried on USB 2.0 ports and 3.0 as well but nothing happens. neither blankflash executes nor any of fastboot or adb commands executes.
will linux OS help ?
Click to expand...
Click to collapse
Never hurts to try, the thing is your phone is in some limbo state and your pc doesn't doesn't see it. I can't imagine that linux will help much. Have you tried holding the power button for a minute or so? I don't know what the sde partition is honestly, but obviously you shouldn't have messed with it. What lead you to that partition and what exactly did you do?
You might uninstall your moto drivers, adb drivers, and fastboot drivers and see if plugging your phone in will detect on your pc as new hardware. Might try installing qualcomm diag drivers to see it it will recognize your phone. I afraid that until your pc sees it, any command is pointless since it can't communicate with your phone.

41rw4lk said:
Never hurts to try, the thing is your phone is in some limbo state and your pc doesn't doesn't see it. I can't imagine that linux will help much. Have you tried holding the power button for a minute or so? I don't know what the sde partition is honestly, but obviously you shouldn't have messed with it. What lead you to that partition and what exactly did you do?
You might uninstall your moto drivers, adb drivers, and fastboot drivers and see if plugging your phone in will detect on your pc as new hardware. Might try installing qualcomm diag drivers to see it it will recognize your phone. I afraid that until your pc sees it, any command is pointless since it can't communicate with your phone.
Click to expand...
Click to collapse
SDE are mobile partitions and I was trying to delete modem partitions as I had installed pie modem on my device and I might have accidentally deleted the bootloader partition or something like that.
after holding power button for a minute nothing happens same screen appears and disappears as I have attached in my previous reply.
is there a button combination which can direct this device in edl mode?
laptop is not reading my device yet, I tried different laptops different ports and different cables. linux is also not reading the device.
please let me know if you know any way I can boot this in edl mode to blankflash. I tried that cable way green and black cable short thats not working either on this device.

latadswapnil said:
SDE are mobile partitions and I was trying to delete modem partitions as I had installed pie modem on my device and I might have accidentally deleted the bootloader partition or something like that.
after holding power button for a minute nothing happens same screen appears and disappears as I have attached in my previous reply.
is there a button combination which can direct this device in edl mode?
laptop is not reading my device yet, I tried different laptops different ports and different cables. linux is also not reading the device.
please let me know if you know any way I can boot this in edl mode to blankflash. I tried that cable way green and black cable short thats not working either on this device.
Click to expand...
Click to collapse
There is no key combo as far as I know to enter edl mode on this phone, and most likely it wouldn't solve your problem. You flashed pie modems on a TMO device, that has been done before and no one has been able to recover from that. Even if you were to somehow get your phone booting, you wouldn't have a baseband or any cell service.

41rw4lk said:
There is no key combo as far as I know to enter edl mode on this phone, and most likely it wouldn't solve your problem. You flashed pie modems on a TMO device, that has been done before and no one has been able to recover from that. Even if you were to somehow get your phone booting, you wouldn't have a baseband or any cell service.
Click to expand...
Click to collapse
While if the OP is correct, and the problem is that they replaced their bootloader, then that's exactly what edl mode is for. However, you're definitely right that there's no key combination. I've been trying to get my moto into edl for days. I even got the battery to die. It just makes other diagnostics more annoying when I need to charge. So far, from what I can tell, the MSM8998 in a Z2 force first of all plays by different rules, uses a different programmer, and is generally not going to respond to the stock "qualcomm unbrick" tutorials. If it gets into edl, then you might be able to blankflash. But I guess keep trying different things, from what I've read the drivers and usb ports are finicky even with phones where this is known to work. It is not known to work with TX1789, at least not with the ease it works in other snapdragon phones. It's actually a massive security vulnerability (if it works it allows arbitrary read/write from the lowest level of the chain of trust, bypassing most security by default. It's a total backdoor), it's just unfortunate we're on that side of the fence. It doesn't have to be that way, but it was designed to see all unsigned software as equally malicious.

latadswapnil said:
I was clearing the sde partitions and my phone suddenly went blank and it is not starting any more.
if I plug it to the laptop it shows charging symbol and "press any key to shutdown" message on left top corner.
It is not getting detected as qualcom or anything it is not booting to bootloader. sometimes it is showing tmobile boot image.
Phone model XT1789-04
Please help , how can blankfash and get the bootloader back? how to go to EDL mode from here ?
Click to expand...
Click to collapse
Does anybody have any new suggestion how I can get into EDL mode?
my phone is still stuck on to the screen where it says press any key to shutdown. It doesn't get detected at all on any USB port or with different cables.
Does anybody know if there are any EDL short points on motherboard or deep flashing cable?
although I tried cutting regular USB C cable for trying to short the two cables and force put it in edl mode but nothing worked yet.
If anybody has any suggestion please throw some light.