Since few days my dataconnection gets lost, when I try to use it. For example when I start Messenger and try to login, TP2 connects then it says Dataconnection is not available check your connection settings. After several attempts it connects stays stable for one or two minutes then again connection breaks down. I also tryed to reset the data connection via connection-wizard, nothing helps. I think something in the registry is messed up...
I don't want to do a hardreset and install all the programs again. Does someone have a good advice for me?
My Rhodium is the same situation. I am a Japanese, and mopera of Docomo is used.
[Understand now]
Cellular Line IP address & Default Gateway is same.
Primary DNS & Secondary DNS is active. I receive PING.
I can't receive PING form other site (mail server etc).
I did hardreset. But my Rhodium is not connect to Internet.
It investigates for a while. If you have good idea, then advice to me.
Same here with MTS Serbia.
I check data connection settings and all adjustment are same like automatic configuration setup but i cant get back data connections.
Hello every one.
I have understood the cause of this problem.
Perhaps, every one set WiFi's DNS server at manual.
If it's possible, set DHCP. Then DNS server is active and you can get e-mail and you can access to Internet.
I think this problem is WM network access process.
I will not use DHCP. I research other process for GPRS.
Thanks msaf, your advice resolve my problem!
I set WiFi's DNS server at manual and when i set on default i got gprs connection again
Hi,
This is an unusual problem as the wireless network card shouldn't have anything to do with GPRS!! Anyway, it seems having automatic DNS for wifi does solve the problem of GPRS but my Wifi connection will not work unless I specify the DNS manually. Therefore, it is a hassle to change between these 2 options whenever I need to change between WIFI and GPRS.
Any way to fix this once and for all??
I looked around the forum and searched on Google but was still skeptical how to connect my Evo to my home internet connection. I turn on my Evo WiFi, it shows my connection so I push connect. Then I see I am unable to to browse from my phone. I have a speedstream 5200 that is connected to my airlink wireless router. I would like to use my home internet so I can browse on my phone. I have a username and password that I have to put in, in order to log on such as my laptop.
Any help will be gratefully appreciated.
Also does this have to do anything with vpn?
Using my HTC Evo phone which I'm using Xda app to post
If your router has a password, the phone should prompt you to enter that. If not, your router could be using a weird security profile, maybe just try switching to WEP. Also, try unplugging the router's power for a minute, then plug it in. That usually fixes any problems with the router itself.
Ill try that and see. If anyone else has this type of issue and somewhat knows how to resolve this pls post. But thank you sitlet Ill give that a shot and respond back asap.
WEP/WPA/WPA2 will all prompt for a password when you try to connect.
A few things to check:
1) The SSID must be set to broadcast
2) make sure there isn't a MAC address filter turned on on the router.
3) if you have entered a password to connect, re-enter it to make sure it is correct.
HTC Evo
Rooted, but still stock...for now
----------------------------------------
The program is designed to work, if it's not, we have a problem.
Ok I did everything mentioned above and I can get into my router settings but I still can't figure out why my Evo won't use my att service. I see the "connect to, my router " but still can't actually connect to use the internet. Am I suppose to use a VPN? please help again my friends, thanks.
Using my HTC Evo phone which I'm using Xda app to post
OP, it sounds like your modem is passing on the PPPoE authentication to the connected client (your computer). What you need to do is have the modem do the PPPoE handshaking and pass a pure public IP back to your router, which then via NAT shares the internet connection across connected devices.
Reference page 21 (not pdf page, but actual page # printed at the bottom of the pages in the pdf) of your modem's owner's manual to provide your login credentials to the modem.
http://www2.windstream.net/downloads/links/SpeedStream211.pdf
On page 38, refer to configuring the modem for client mode.
You should configure your router for DHCP wan mode. You may need to adjust your MTU setting if there is one. I don't recall the exact procedure for dsl setups, but google "optimal mtu dsl" for information.
Finally, your computer should be set up for dhcp as well. When everything is working properly, you should not need to run any additional software on your computer to gain internet access. When this becomes so, your evo should be able to connect successfully to your wifi. Once you're able to do this, you can start implementing wireless security (wep/wpa/wpa2).
Edit: You're not clear what you're typing in when you reference logging in in one of the posts above. Are you supplying windows credentials, or your isp credentials ([email protected] or [email protected] or similar and password)?
Hi, I cant get Wif-Ace to work( it just goes to a black screen when i open it) and when it works I dont know how to set it up so i can use wifi! Can you help?!
Try this version from google code. It works fine on my TP2. As far as settings, I basically turned off everything except WEP password. It depends on how your wireless router is set up. Just match wifi-ace settings to what is on your router.
http://code.google.com/p/android-wifi-ace/downloads/detail?name=WiFiACE-0.10-20100924.apk
WEP is EXTREMELY insecure. If you have any option, get rid of WEP. If it's not your router, tell whoever owns the router that it is a very insecure protocol and any script kiddie with a laptop can bust into it in less than 2 minutes.
Don't use WEP!!!!
But i need WEP so i can download apps faster!!!
x12CHRIS18x said:
But i need WEP so i can download apps faster!!!
Click to expand...
Click to collapse
Uh... what? You really think it's that much faster than WPA? Might as well just run an open network. I seriously doubt that WPA/2 adds that much overhead...
di what i do change my modem to wpa2 more fast and more secure before wep easy hack
wep i have ap rogram with the madem of you modem i now you speedtouch password
how do you change it to WPA2
x12CHRIS18x said:
how do you change it to WPA2
Click to expand...
Click to collapse
How did you change it to WEP?
The security settings are in your router. Kinda outside of the scope of not just XDAndroid, but xda-devs in general.
I didnt change it to WEP, it just came that way when i bought internet and i dont think i can change it to WPA2 cause i have 2WIRE
x12CHRIS18x said:
I didnt change it to WEP, it just came that way when i bought internet and i dont think i can change it to WPA2 cause i have 2WIRE
Click to expand...
Click to collapse
Tell your provider then.
i use is wpa2-psk and work with everything waring when you have to this key you have to reconnect everything to the router (put the password again to every equipment). one time i used wpa2 the first some with the modem and docent work very well
Originally Posted by x12CHRIS18x View Post
I didnt change it to WEP, it just came that way when i bought internet and i dont think i can change it to WPA2 cause i have 2WIRE
http://www.pauldavidolson.com/blog/...s-router-from-wep-to-wpa2-network-encryption/ search google
http://www.google.com/search?q=wpa2...org.mozilla:en-US:unofficial&client=firefox-a
2WIRE gateways support WPA/2.
Thanks emanuelrv, I changed it to WPA2
Hey,
I want to connect to a 802.1x security wifi network on my school, it does connect.
It sais I am connected but I can't browse the web and all my apps dont refresh either.
Is there anyway I can fix this? Maybe with some setting or change in root?
work fine on mine
I'll install cm9 as soon as I can, and see if it fixes my probs. Otherwise it could be a chipset problem, that it just doesnt support. Some other people on my school also cant connect (budget phones).
I think its weird that some devices can connect and others not, on my school, some galaxy s or galaxy ace will connect while others can't. I have cyanogenmod 7.2 with android 2.3.7! I think it should work but someway it keeps connected, so I am connected to the router, but I can't browse the net. Maybe it cant open default gateway in someway?
maybe that router is not compatible .. i have the same problem in some places..
I think it's weird some devices connect and other do not, maybe it has to due with diffrence in android versions? I use cyanogenmod 7.2, android gingerbread 2.3.7
Oi, there is so much that could be going on here...
Its an Atheros AR6003G chip, which as far as i know, supports 802.11 A/B/G/N, and hardware encryption for WEP/WPA...
Odds are, if its an 802.1x type network, the chip will do the encrypting/decrypting after the handshake is completed, provided its set up correctly. WEP and WPA are set up by using a Pre-shared Key that all users need to have... If you study how to recover the key, you'll find that the hash is created by taking the plaintext passkey, running it through the specified algorithm, then salting it with the name of the network. So long as all devices have the correct network name and the correct plaintext password, any device can connect to the network, because they'll all end up with the same hash.
802.1x encryption is different. It uses an authentication server. This makes it similar to any modern computer you log onto. You provide the computer with your credentials, and it checks it against the server. If they match, then you are allowed access. If they don't you get an error message. Which means, that if anything is broken, it won't work. If you don't use the correct authentication protocol, it won't work. If you don't have the right certificates, it won't work.
Best advice I can give is, double check everything. Make sure your Gio has the correct certificates and that its using the correct protocols. Double check your IP/Subnet Mask/Gateway addresses. If you don't have an IP address, you'll have to manually configure it. If the Subnet Mask is incorrect or the Gateway address is incorrect, it won't work either. Also, check your DNS server addresses. If those aren't correct it won't load any webpages using URLs. It will only load them using the IP address of the server. Which means, telling the browser to go to www.google.com won't work, but if you tell it to go to 173.194.67.99:80, it will load the Google homepage.
Hopefully this will give you somewhere to start...
Yes true, only problem is that static IP's dont work, otherwise I could just copy the DNS and gateway numbers from a device it does work on. It uses DHCP and I think that I have the problem you told about.I dont think our school uses certificates cause a friend of my (Galaxy S) can connect without having installed certificates or something.
I think its an hardware isue and it cant decrypt the code well, my WIFI indicator stays white, with internet acces it should turn blue or green.
runedegroot said:
Yes true, only problem is that static IP's dont work, otherwise I could just copy the DNS and gateway numbers from a device it does work on. It uses DHCP and I think that I have the problem you told about.I dont think our school uses certificates cause a friend of my (Galaxy S) can connect without having installed certificates or something.
I think its an hardware isue and it cant decrypt the code well, my WIFI indicator stays white, with internet acces it should turn blue or green.
Click to expand...
Click to collapse
What if you go to wifi settings- menu button - advanced settings- 'regulier domein' I know you are dutch, dont know how it is called in english, something like regular domain I guess.
Then set it to 11 13 or 14 try them out, fixes my wifi, also at school with 8.11x connection mode
Sent from my GT-S5660 using xda premium
runedegroot said:
Yes true, only problem is that static IP's dont work, otherwise I could just copy the DNS and gateway numbers from a device it does work on. It uses DHCP and I think that I have the problem you told about.I dont think our school uses certificates cause a friend of my (Galaxy S) can connect without having installed certificates or something.
I think its an hardware isue and it cant decrypt the code well, my WIFI indicator stays white, with internet acces it should turn blue or green.
Click to expand...
Click to collapse
That is very very odd... I use a Linksys WRT54G2 router at home, and its set up for DHCP. Its address is the standard 192.168.1.1, and it can address 50 clients between the addresses of 192.168.1.100 and 192.168.1.149. However, if i set my computer up to use static settings, it works just fine... Granted the networks are probably set up differently.... but the theory should work just fine...
Code:
IP: 192.168.1.4
Subnet Mask: 255.255.255.0
Gateway 192.168.1.1
DNS: 64.59.160.13, 64.59.160.15
Are you positive it doesn't work?
If you can get me the encryption type, IP address, Subnet Mask and Gateway address your friends phone uses, I may be able to help more... The more information you can get me, the better.
The only reason I can think of that would cause it to not work is that the IP address is already in use, or the Subnet mask is incorrect... It shouldn't matter what IP address you use, so long as the subnet mask and gateway are correct... In theory anyway...
I'll gather them and put them in a post!
Thanks for your help so far,
Im on the same school as runedegroot but the neteork does work for me, and i dont think a stattic ip will work cause the network is spread over a lot of routers so if any other phone gets that ip via dhcp it wont work anymore
Sent from my GT-I9000 using xda premium
Well, apparently DHCP doesn't work for him, so whats he have to loose?
Although that's quite interesting... What phone do you use, and whats the network information you have when you're connected to your school's network?
voetbalremco said:
What if you go to wifi settings- menu button - advanced settings- 'regulier domein' I know you are dutch, dont know how it is called in english, something like regular domain I guess.
Then set it to 11 13 or 14 try them out, fixes my wifi, also at school with 8.11x connection mode
Sent from my GT-S5660 using xda premium
Click to expand...
Click to collapse
I'll try, it didn't give me positive feedback when I tried it on MC 7.2, I'll try monday.
Btw, voetbalremco is a dutch name, you also have a dutch thumbnail, but you aint dutch?
atirox said:
Well, apparently DHCP doesn't work for him, so whats he have to loose?
Although that's quite interesting... What phone do you use, and whats the network information you have when you're connected to your school's network?
Click to expand...
Click to collapse
I use galaxy gio, gt-s5660. Maybe willie1001 knows it, I can't see it when I'm at home.
I have the same problem
runedegroot said:
I'll try, it didn't give me positive feedback when I tried it on MC 7.2, I'll try monday.
Btw, voetbalremco is a dutch name, you also have a dutch thumbnail, but you aint dutch?
Click to expand...
Click to collapse
Im dutch, but the forum is english so I also post in english, I dont like it neither if people post in polish or whatever I cant read..
Sent from my GT-S5660 using xda premium
runedegroot said:
I use galaxy gio, gt-s5660. Maybe willie1001 knows it, I can't see it when I'm at home.
Click to expand...
Click to collapse
Actually that was for willie1001...
And its possible that changing the reguatory domain could work. If you're running software designed for the states, it would disable any channel above 11... But then again, if you can "see" the wireless network in the settings menu, it would make sense that its programmed to use a channel isn't above channel 11... Which would mean that changing the regulatory domain wouldn't help it at all...
Come to think of it, if your MAC address is blocked, it wouldn't allow you access... But then again, you'd have to do something for the school to block your MAC address. And if the other students can access it, then it would have to be specifically you who did something to piss off a teacher.
Also, any information you can get me about the router would help greatly. By figuring out the manufacturer of the router and the model number of the router, its possible to narrow down the likely IP addresses that the router would use..
atirox said:
Actually that was for willie1001...
And its possible that changing the reguatory domain could work. If you're running software designed for the states, it would disable any channel above 11... But then again, if you can "see" the wireless network in the settings menu, it would make sense that its programmed to use a channel isn't above channel 11... Which would mean that changing the regulatory domain wouldn't help it at all...
Come to think of it, if your MAC address is blocked, it wouldn't allow you access... But then again, you'd have to do something for the school to block your MAC address. And if the other students can access it, then it would have to be specifically you who did something to piss off a teacher.
Also, any information you can get me about the router would help greatly. By figuring out the manufacturer of the router and the model number of the router, its possible to narrow down the likely IP addresses that the router would use..
Click to expand...
Click to collapse
Haha no, I didn't piss of a teacher
I think it's a gio problem, willie1001 has the galaxy s with cyanogenmod 9.
I have gio with cyanogenmod 9. But it also didnts work with stock or cyanogenmod 7.
I will send you some information I can see on my phone, if I won't forget it
runedegroot said:
Haha no, I didn't piss of a teacher
I think it's a gio problem, willie1001 has the galaxy s with cyanogenmod 9.
I have gio with cyanogenmod 9. But it also didnts work with stock or cyanogenmod 7.
I will send you some information I can see on my phone, if I won't forget it
Click to expand...
Click to collapse
Man, thats odd... I assume you aren't on the North American continent... Where did you pick your Gio up from?
You know... Its possible that the issue you have was fixed in a base band (modem) update... You could try flashing the phone to the latest OE firmware (Not necessarily the one that came with your carrier as branded firmware tends to take forever to get updated), and see if that works...
Hi I can't connect with my wifi connection: i set the password, i press "connect", but nothing happens, no errors, but the wifi doesn't connect!
With other wifi's this phone works. What can I do?
Sounds like a router problem then.
If your router is broadcasting at a high channel, try setting the router to broadcast on a low channel, maybe 4, 5, or 6.
martonikaj said:
Sounds like a router problem then.
Click to expand...
Click to collapse
Yes I think It's that, how can i solve it?
TheSignal said:
Yes I think It's that, how can i solve it?
Click to expand...
Click to collapse
If you’re using a Linksys router, you’ll need to browse to the address of your router, which is probably set to http://192.168.1.1 but could be assigned to another address. You can run a quick ipconfig command at the command prompt to check.
In my case the address is different (because I changed it, of course), but what you’re looking for is the Default Gateway for your Wireless connection, and then go to http://<Default Gateway> in your browser. Enter in the password that you hopefully remember, and head to the Wireless –> Basic Wireless Settings tab.